Ocean Thermal Energy Conversion (OTEC) is a technology by which thermal energy from the ocean is harnessed and converted into electricity. It is one of the renewable energy technologies being researched into, as part of solutions to the challenge of global warming and climate change. A major setback of this technology, however, is that it has a very low cycle efficiency. In this work a cogeneration cycle is proposed which is driven by the temperature difference between the warm surface layer and the cold bottom layer of the ocean. The work is aimed at improving the overall cycle efficiency of OTEC systems by reducing the depth at which cold water is captured from the ocean. To achieve this, the cycle employs a binary mixture of ammonia and water as the working fluid and uses the mechanism of absorption to obtain the liquid phase of the working fluid after expansion through the turbine. The effects of varying cycle parameters such as the depth of cold-water capture, heat source temperature and mixture composition of the working fluid were investigated. With a basic solution mixture concentration of 0.40 kg/kg NH3/H2O, and under operating conditions of 30oC as the warm surface water temperature and a cold water temperature of 10oC, captured at a depth of 600m the proposed cycle produced a net power output of 42 kW, and a refrigeration capacity of 370 kW. The thermal efficiency computed was 1.94% and the exergy efficiency was 13.78%, both higher than the case where the depth of cold water capture was 1000m.
This document discusses various thermodynamic power cycles including:
- The Carnot cycle, which is the most efficient but impractical cycle.
- Rankine cycles, which are more practical vapor power cycles that use steam as the working fluid.
- Simple Rankine cycles involve heating water to steam then expanding it in a turbine before condensing it back to water.
- Rankine cycles with superheated steam, which increase efficiency by heating steam above its saturation temperature.
- The efficiencies of different cycles are calculated and compared in examples. Superheated steam cycles have higher efficiencies than simple Rankine cycles due to higher average temperatures.
Seminar Report on Automobile Air-Conditioning based on VAC using Exhaust HeatBhagvat Wadekar
The theoretical analysis, the feasibility of such a system in a positive frame. It can be summarized that: In the exhaust gases of motor vehicles, there is enough heat energy that can be utilized to power an air-conditioning system. Therefore, if air-conditioning is achieved without using the engine’s mechanical output, there will be a net reduction in fuel consumption and emissions. Once a secondary fluid such as water or glycol is used, the aqua-ammonia combination appears to be a good candidate as a working fluid for an absorption car air-conditioning system. This minimizes any potential hazard to the passengers. The low COP value is an indication that improvements to the cycle are necessary. A high purity refrigerant would give a higher refrigeration effect, while the incorporation of a solution heat exchanger would reduce the input heat to the generator. The present system has both a reflux condenser and a heat exchanger. However, the reflux condenser is proved inadequate to provide high purity of the refrigerant and needs to be re-addressed. The evaluation of the COP, with and without the heat exchanger also proves that unless there is a high purity refrigerant, the effect of the heat exchanger to the generator’s heat is small.
Investigating The Performance of A Steam Power PlantIJMERJOURNAL
ABSTRACT: The performance analysis of Shobra El-Khima power plant in Cairo, Egypt is presented based on energy and exergy analysis to determine the causes , the sites with high exergy destruction , losses and the possibilities of improving the plant performance. The performance of the plant was evaluated at different loads (Full, 75% and, 50 %). The calculated thermal efficiency based on the heat added to the steam was found to be 41.9 %, 41.7 %, 43.9% , while the exergetic efficiency of the power cycle was found to be 44.8%, 45.5% and 48.8% at max, 75% and, 50 % load respectively. The condenser was found to have the largest energy losses where (54.3%, 55.1% and 56.3% at max, 75% and, 50 % load respectively) of the added energy to the steam is lost to the environment. The maximum exergy destruction was found to be in the turbine where the percentage of the exergy destruction was found to be (42%, 59% and 46.1% at max, 75% and, 50 % load respectively). The pump was found to have the minimum exergy destruction. It was also found that the exergy destruction in feed water heaters and in the condenser together represents the maximum exergy destruction in the plant (about 52%). This means that the irreversibilities in the heat transfer devices in the plant have a significant role on the exergy destruction. So, it is thought that the improvement in the power plant will be limited due to the heat transfer devices.
This document provides information on entropy and thermodynamics concepts including:
1. Entropy is a measure of irreversibilities and increases for all actual processes, being conserved only for idealized reversible processes.
2. Processes can only occur in the direction that complies with the increase of entropy principle.
3. Gas turbine cycles including Brayton, jet propulsion, and modifications like regeneration, intercooling and reheating are discussed. The efficiency and performance of these cycles depends on parameters like pressure and temperature ratios.
This document provides information about the Thermal Engineering course ME6404 for 4th semester mechanical engineering students at RMK College of Engineering and Technology. It was compiled by Assistant Professor Bibin C. The course covers gas power cycles, internal combustion engines, steam nozzles and turbines, air compressors, and refrigeration and air conditioning systems. It lists the course objectives, units of study, textbooks, and references. The document also provides definitions and explanations of key concepts in thermal engineering such as work, heat, entropy, and processes like isothermal, adiabatic, throttling and free expansion.
The document analyzes the thermodynamic performance of a lithium bromide (LiBr) and water based vapor absorption air conditioning system that utilizes waste exhaust heat from a diesel engine. The system consists of a generator, condenser, evaporator, absorber, and solution heat exchanger. The effects of varying the temperatures of these components on the system's coefficient of performance (COP) and exergy efficiency are examined. The results show that COP increases with higher evaporator temperature but decreases with higher condenser and absorber temperatures. Exergy analysis indicates the condenser and absorber have higher exergy losses than the generator and evaporator. A small-scale LiBr-water system can feasibly operate using exhaust heat from
Thermal engineering concepts are summarized in three sentences: Thermodynamics is the study of heat, work, and energy in systems and their transformations. The first law of thermodynamics states that energy is conserved in any process. The second law indicates that entropy increases in closed systems, limiting the conversion of heat into work and establishing an irreversible direction for spontaneous change. Various power plants including thermal, hydroelectric, nuclear, solar and wind are described that convert heat or other energy sources into electricity using thermodynamic cycles and principles.
This document provides information about gas turbine and steam power plant cycles. It describes the Brayton cycle used in gas turbines and the Rankine cycle used in steam power plants. It discusses components, processes, thermal efficiencies and improvements to the cycles such as regeneration, intercooling and reheating. Examples are provided to calculate efficiency, work and heat inputs/outputs for simple and improved cycles.
This document discusses various thermodynamic power cycles including:
- The Carnot cycle, which is the most efficient but impractical cycle.
- Rankine cycles, which are more practical vapor power cycles that use steam as the working fluid.
- Simple Rankine cycles involve heating water to steam then expanding it in a turbine before condensing it back to water.
- Rankine cycles with superheated steam, which increase efficiency by heating steam above its saturation temperature.
- The efficiencies of different cycles are calculated and compared in examples. Superheated steam cycles have higher efficiencies than simple Rankine cycles due to higher average temperatures.
Seminar Report on Automobile Air-Conditioning based on VAC using Exhaust HeatBhagvat Wadekar
The theoretical analysis, the feasibility of such a system in a positive frame. It can be summarized that: In the exhaust gases of motor vehicles, there is enough heat energy that can be utilized to power an air-conditioning system. Therefore, if air-conditioning is achieved without using the engine’s mechanical output, there will be a net reduction in fuel consumption and emissions. Once a secondary fluid such as water or glycol is used, the aqua-ammonia combination appears to be a good candidate as a working fluid for an absorption car air-conditioning system. This minimizes any potential hazard to the passengers. The low COP value is an indication that improvements to the cycle are necessary. A high purity refrigerant would give a higher refrigeration effect, while the incorporation of a solution heat exchanger would reduce the input heat to the generator. The present system has both a reflux condenser and a heat exchanger. However, the reflux condenser is proved inadequate to provide high purity of the refrigerant and needs to be re-addressed. The evaluation of the COP, with and without the heat exchanger also proves that unless there is a high purity refrigerant, the effect of the heat exchanger to the generator’s heat is small.
Investigating The Performance of A Steam Power PlantIJMERJOURNAL
ABSTRACT: The performance analysis of Shobra El-Khima power plant in Cairo, Egypt is presented based on energy and exergy analysis to determine the causes , the sites with high exergy destruction , losses and the possibilities of improving the plant performance. The performance of the plant was evaluated at different loads (Full, 75% and, 50 %). The calculated thermal efficiency based on the heat added to the steam was found to be 41.9 %, 41.7 %, 43.9% , while the exergetic efficiency of the power cycle was found to be 44.8%, 45.5% and 48.8% at max, 75% and, 50 % load respectively. The condenser was found to have the largest energy losses where (54.3%, 55.1% and 56.3% at max, 75% and, 50 % load respectively) of the added energy to the steam is lost to the environment. The maximum exergy destruction was found to be in the turbine where the percentage of the exergy destruction was found to be (42%, 59% and 46.1% at max, 75% and, 50 % load respectively). The pump was found to have the minimum exergy destruction. It was also found that the exergy destruction in feed water heaters and in the condenser together represents the maximum exergy destruction in the plant (about 52%). This means that the irreversibilities in the heat transfer devices in the plant have a significant role on the exergy destruction. So, it is thought that the improvement in the power plant will be limited due to the heat transfer devices.
This document provides information on entropy and thermodynamics concepts including:
1. Entropy is a measure of irreversibilities and increases for all actual processes, being conserved only for idealized reversible processes.
2. Processes can only occur in the direction that complies with the increase of entropy principle.
3. Gas turbine cycles including Brayton, jet propulsion, and modifications like regeneration, intercooling and reheating are discussed. The efficiency and performance of these cycles depends on parameters like pressure and temperature ratios.
This document provides information about the Thermal Engineering course ME6404 for 4th semester mechanical engineering students at RMK College of Engineering and Technology. It was compiled by Assistant Professor Bibin C. The course covers gas power cycles, internal combustion engines, steam nozzles and turbines, air compressors, and refrigeration and air conditioning systems. It lists the course objectives, units of study, textbooks, and references. The document also provides definitions and explanations of key concepts in thermal engineering such as work, heat, entropy, and processes like isothermal, adiabatic, throttling and free expansion.
The document analyzes the thermodynamic performance of a lithium bromide (LiBr) and water based vapor absorption air conditioning system that utilizes waste exhaust heat from a diesel engine. The system consists of a generator, condenser, evaporator, absorber, and solution heat exchanger. The effects of varying the temperatures of these components on the system's coefficient of performance (COP) and exergy efficiency are examined. The results show that COP increases with higher evaporator temperature but decreases with higher condenser and absorber temperatures. Exergy analysis indicates the condenser and absorber have higher exergy losses than the generator and evaporator. A small-scale LiBr-water system can feasibly operate using exhaust heat from
Thermal engineering concepts are summarized in three sentences: Thermodynamics is the study of heat, work, and energy in systems and their transformations. The first law of thermodynamics states that energy is conserved in any process. The second law indicates that entropy increases in closed systems, limiting the conversion of heat into work and establishing an irreversible direction for spontaneous change. Various power plants including thermal, hydroelectric, nuclear, solar and wind are described that convert heat or other energy sources into electricity using thermodynamic cycles and principles.
This document provides information about gas turbine and steam power plant cycles. It describes the Brayton cycle used in gas turbines and the Rankine cycle used in steam power plants. It discusses components, processes, thermal efficiencies and improvements to the cycles such as regeneration, intercooling and reheating. Examples are provided to calculate efficiency, work and heat inputs/outputs for simple and improved cycles.
The document provides information on several thermodynamic cycles used in power plants and engines, including:
1) The Carnot, Stirling, Ericsson, Brayton, Rankine, and Otto cycles. Equations for calculating efficiency are provided for some cycles.
2) Diagrams show the pressure-volume or temperature-entropy processes involved in each cycle. The Carnot cycle involves two isothermal and two adiabatic processes. The Stirling cycle has four processes: two isothermal and two isochoric.
3) The Rankine cycle closely describes the steam power cycle. It involves isobaric heating of liquid to steam, isentropic expansion in a turbine, isobar
The document provides information about thermodynamics and various types of power plants. It discusses key concepts in thermodynamics including systems, properties, laws of thermodynamics, and heat engines. It also describes different power plant technologies like thermal, hydroelectric, nuclear, solar, and wind power plants. Their basic working principles and components are explained along with the advantages and disadvantages of each type of power plant.
This document provides information about a lecture on reheat and intercooling in gas turbine systems. It includes:
- An explanation of the concepts and purposes of using reheat and intercooling in gas turbines.
- An example problem calculating efficiency and mass flow rate for a gas turbine cycle with reheat and intercooling.
- Diagrams of gas turbine cycles with the different enhancements labeled.
Automobile air conditioning based on VAC using exhaust heatBhagvat Wadekar
The theoretical analysis, the feasibility of such a system in a positive frame. It can be summarized that: In the exhaust gases of motor vehicles, there is enough heat energy that can be utilized to power an air-conditioning system. Therefore, if air-conditioning is achieved without using the engine’s mechanical output, there will be a net reduction in fuel consumption and emissions. Once a secondary fluid such as water or glycol is used, the aqua-ammonia combination appears to be a good candidate as a working fluid for an absorption car air-conditioning system. This minimizes any potential hazard to the passengers. The low COP value is an indication that improvements to the cycle are necessary. A high purity refrigerant would give a higher refrigeration effect, while the incorporation of a solution heat exchanger would reduce the input heat to the generator. The present system has both a reflux condenser and a heat exchanger. However, the reflux condenser is proved inadequate to provide high purity of the refrigerant and needs to be re-addressed. The evaluation of the COP, with and without the heat exchanger also proves that unless there is a high purity refrigerant, the effect of the heat exchanger to the generator’s heat is small.
This document provides a mid-term review covering three topics: 1) energy analysis of closed systems, 2) mass and energy analysis of control volumes, and 3) the second law of thermodynamics. For the first topic, it provides examples of energy balance calculations for constant pressure processes in closed systems. For the second topic, it discusses the energy balance equation for control volumes and provides examples of its application to turbines, compressors, and throttling valves. For the third topic, it defines thermal efficiency and the coefficient of performance and discusses heat engines, refrigerators, and heat pumps.
The document discusses thermal power cycles. It begins by explaining that a thermal power plant involves heating water to create steam that spins a turbine and generates electricity.
The basic energy flow in a thermal power plant is: chemical energy is converted to mechanical energy by the steam turbine, which is then converted to electrical energy. Various fuel sources can be used.
It then discusses the key power cycles used in thermal plants like the Carnot, Rankine, Diesel, Otto, and Brayton cycles. It also covers the laws of thermodynamics and important thermodynamic processes.
The Rankine cycle most closely models actual steam power plants. It involves pumping water, boiling it to create steam, expanding the steam
The document discusses the second law of thermodynamics. It explains that the first law has limitations and does not determine whether a process is possible. The second law states that heat cannot spontaneously flow from a cold body to a hot body. It presents two common statements of the second law by Kelvin and Clausius. The document also discusses entropy, ideal gas entropy changes, and the reversible Carnot cycle.
Eg 261 - 2-4 laws of thermodynamics and thermodynamic efficiencyLTECEng SwanseaUni
This document contains information from a thermodynamics lecture on heat engines and the laws of thermodynamics. It discusses key concepts like system boundaries, heat vs work, the first law of conservation of energy, and the second law regarding the direction of energy transfer and limits on converting heat fully to work. Examples are provided comparing performance of car engines and jet engines. Students are given a problem calculating properties of a jet engine experiment. The maximum theoretical fuel efficiencies of jet engines and all heat engines are discussed.
The document discusses thermal power cycles and the Rankine cycle in particular. It provides details on:
- The basic energy flow in a thermal power plant from chemical to mechanical to electrical energy.
- The Rankine cycle most closely models the steam power cycle used in most power plants. It involves heating water to steam to drive a turbine and then condensing the steam to recycle the water.
- Ways to improve the efficiency of the Rankine cycle include increasing the average temperature of heat addition by superheating steam or increasing boiler pressure, and decreasing the average temperature of heat rejection by lowering the condenser pressure.
Download Link (Copy URL):
https://sites.google.com/view/varunpratapsingh/teaching-engagements
Syllabus:
Availability and Irreversibility
Availability Function
Second Law Efficiencies
Work Potential Associated with Internal Energy
Waste Heat Recovery
Heat Losses – Quality vs. Quantity
Principle of Heat Recovery Units
Classification of WHRS on Temperature Range Bases
Commercial Viable Waste Heat Recovery Devices
Benefits of Waste Heat Recovery
Development of a Waste Heat Recovery System
Commercial Waste Heat Recovery Devices
West Heat Recovery Boiler (WHRB)
Recuperators- Regenerative, Ceramic, Regenerative Heat Exchanger
Thermal wheel/ Heat Wheel
Heat Pipe
Economiser
Feed Water
Heat Pump
Shell and Tube Heat Exchanger
Plate Heat Exchanger
Run-around coil
Direct Contact Heat Exchanger
Advantages and Limitations of WHRD’s
This document presents information on the Rankine cycle. It contains the following key points:
1. The Rankine cycle converts heat into work through a closed loop that uses water as the working fluid. It generates about 90% of the world's electric power.
2. An ideal Rankine cycle involves isothermal and isobaric processes, while a real cycle involves non-reversible and isentropic compression and expansion.
3. Variations like the reheat cycle and regeneration cycle can improve the efficiency by reheating steam before the turbine or preheating feedwater, but increase costs.
This document discusses the reheat cycle in thermodynamics. The reheat cycle is a modification of the Rankine cycle that is used in steam power plants. It works by reheating the steam after it expands in the high-pressure turbine and before it expands further in the low-pressure turbine. This increases the efficiency by raising the mean temperature of heat addition and reducing moisture content in the steam. Reheating allows for higher turbine work extraction and thermal efficiency compared to the basic Rankine cycle. The document examines the working of reheat cycles in steam turbines and thermal power plants, and their advantages in improving efficiency and reducing blade erosion.
This document discusses various thermodynamic cycles used in power generation applications including vapor power cycles, gas power cycles, and gas turbine cycles. It describes the basic processes and assumptions of cycles like the Rankine, Otto, diesel, and Brayton cycles. Methods to improve the performance of these cycles are also covered, such as increasing boiler pressure, superheating, reheating, and regeneration. The key applications of thermodynamics discussed are steam power plants, internal combustion engines, and gas turbine engines.
The document discusses Heat Recovery Steam Generators (HRSGs). HRSGs recover heat from gas turbine exhaust to produce steam. They operate in either combined cycle mode, where steam drives a turbine, or cogeneration mode where steam is used for industrial processes. HRSGs contain evaporator, economizer, and superheater sections to produce steam. They can also include reheaters, deaerators, and preheaters. HRSGs come in natural circulation, forced circulation, or once-through designs and can be unfired, fired, supplementary fired, or exhaust fired depending on heat input. HRSGs vary in operation pressure as either single or multi-pressure. Post-combustion emission controls like
This document provides an overview of various gas power cycles used in thermal engineering. It discusses the Otto, Diesel, dual, Brayton, and other cycles. For each cycle, it describes the key processes on P-V and T-S diagrams, such as isentropic compression and expansion and constant volume or pressure heat addition/rejection. It also provides the efficiency equations for ideal versions of the Otto, Diesel, and Brayton cycles. Real-world examples of engines using different cycles are given at the end.
Hrsg & turbine as run energy efficiency assessmentD.Pawan Kumar
The document provides measurements and performance data from an assessment of a heat recovery steam generator (HRSG) and steam turbine system. Key findings include:
- The HRSG achieved an overall thermal efficiency of 84.43% based on measured temperature and flow data.
- Heat was recovered across multiple components, with the high pressure evaporator recovering the most at 41.95% of total heat.
- The steam turbine achieved an overall efficiency of 78.40% based on measured steam and electrical output values.
The document provides information about the Brayton cycle used in gas turbines. It begins with an introduction to the Brayton cycle and gas turbines. It then describes the key components of a gas turbine system using the Brayton cycle, including the compressor, combustion chamber, and turbine. It also discusses the classifications of gas turbines as open cycle or closed cycle. Methods to improve the efficiency of the Brayton cycle like intercooling, reheating, and regeneration are covered. Applications of gas turbines and the advantages and disadvantages are summarized at the end.
This article investigates the thermal performance of a heat pipe heat exchanger for heat recovery in air conditioning applications. Experiments were conducted with ratios of return to fresh air mass flow rates of 1, 1.5, and 2.3. The fresh air inlet temperature was varied from 32°C to 40°C while the return air temperature was kept at 26°C. The results show that the temperature changes and effectiveness of both the evaporator and condenser sections increase with higher fresh air inlet temperatures. The enthalpy ratio between heat recovery and conventional air mixing also increases with fresh air inlet temperature, reaching 85% at 40°C.
This document provides lecture notes on gas power cycles from a mechanical engineering course. It covers the ideal gas relation, specific heats of gases, and the first law of thermodynamics as they relate to closed systems. Formulas are presented for the ideal gas law in various forms, as well as specific heat capacities for air. The notes also define important terms used in analyzing thermodynamic cycles, such as pressure ratio, compression ratio, and cutoff ratio. An example problem is included to demonstrate calculating maximum pressure, net specific work, and thermal efficiency for a diesel engine cycle.
This document analyzes the performance of different ocean thermal energy conversion cycles, including single-stage Rankine, double-stage Rankine, and Kalina cycles. It finds that double-stage Rankine and Kalina cycles, which use multiple heat exchangers or working fluid mixtures, can improve power output over a single-stage Rankine cycle by reducing irreversible losses during heat exchange. The analysis applies a simple method to evaluate temperature differences between working fluids and seawater in order to compare the system characteristics and effectiveness of reducing these losses across cycle types.
Review of enhancement for ocean thermal energy conversion system.pdfIreneKoronaki1
This document provides a review of enhancement strategies for ocean thermal energy conversion (OTEC) systems. It discusses various closed thermodynamic cycles that can be used in OTEC, including the basic Rankine cycle. Different working fluids are described, such as ammonia and ammonia-water mixtures, and how they affect cycle efficiency. The document also examines the impact of the ejector on cycle performance. Several methods to improve thermal efficiency are presented, such as intermediate extraction, heat recovery, reheating, and two-stage cycles. The most effective approaches are evaluated under identical operating conditions to determine which strategy provides the highest efficiency for OTEC.
The document provides information on several thermodynamic cycles used in power plants and engines, including:
1) The Carnot, Stirling, Ericsson, Brayton, Rankine, and Otto cycles. Equations for calculating efficiency are provided for some cycles.
2) Diagrams show the pressure-volume or temperature-entropy processes involved in each cycle. The Carnot cycle involves two isothermal and two adiabatic processes. The Stirling cycle has four processes: two isothermal and two isochoric.
3) The Rankine cycle closely describes the steam power cycle. It involves isobaric heating of liquid to steam, isentropic expansion in a turbine, isobar
The document provides information about thermodynamics and various types of power plants. It discusses key concepts in thermodynamics including systems, properties, laws of thermodynamics, and heat engines. It also describes different power plant technologies like thermal, hydroelectric, nuclear, solar, and wind power plants. Their basic working principles and components are explained along with the advantages and disadvantages of each type of power plant.
This document provides information about a lecture on reheat and intercooling in gas turbine systems. It includes:
- An explanation of the concepts and purposes of using reheat and intercooling in gas turbines.
- An example problem calculating efficiency and mass flow rate for a gas turbine cycle with reheat and intercooling.
- Diagrams of gas turbine cycles with the different enhancements labeled.
Automobile air conditioning based on VAC using exhaust heatBhagvat Wadekar
The theoretical analysis, the feasibility of such a system in a positive frame. It can be summarized that: In the exhaust gases of motor vehicles, there is enough heat energy that can be utilized to power an air-conditioning system. Therefore, if air-conditioning is achieved without using the engine’s mechanical output, there will be a net reduction in fuel consumption and emissions. Once a secondary fluid such as water or glycol is used, the aqua-ammonia combination appears to be a good candidate as a working fluid for an absorption car air-conditioning system. This minimizes any potential hazard to the passengers. The low COP value is an indication that improvements to the cycle are necessary. A high purity refrigerant would give a higher refrigeration effect, while the incorporation of a solution heat exchanger would reduce the input heat to the generator. The present system has both a reflux condenser and a heat exchanger. However, the reflux condenser is proved inadequate to provide high purity of the refrigerant and needs to be re-addressed. The evaluation of the COP, with and without the heat exchanger also proves that unless there is a high purity refrigerant, the effect of the heat exchanger to the generator’s heat is small.
This document provides a mid-term review covering three topics: 1) energy analysis of closed systems, 2) mass and energy analysis of control volumes, and 3) the second law of thermodynamics. For the first topic, it provides examples of energy balance calculations for constant pressure processes in closed systems. For the second topic, it discusses the energy balance equation for control volumes and provides examples of its application to turbines, compressors, and throttling valves. For the third topic, it defines thermal efficiency and the coefficient of performance and discusses heat engines, refrigerators, and heat pumps.
The document discusses thermal power cycles. It begins by explaining that a thermal power plant involves heating water to create steam that spins a turbine and generates electricity.
The basic energy flow in a thermal power plant is: chemical energy is converted to mechanical energy by the steam turbine, which is then converted to electrical energy. Various fuel sources can be used.
It then discusses the key power cycles used in thermal plants like the Carnot, Rankine, Diesel, Otto, and Brayton cycles. It also covers the laws of thermodynamics and important thermodynamic processes.
The Rankine cycle most closely models actual steam power plants. It involves pumping water, boiling it to create steam, expanding the steam
The document discusses the second law of thermodynamics. It explains that the first law has limitations and does not determine whether a process is possible. The second law states that heat cannot spontaneously flow from a cold body to a hot body. It presents two common statements of the second law by Kelvin and Clausius. The document also discusses entropy, ideal gas entropy changes, and the reversible Carnot cycle.
Eg 261 - 2-4 laws of thermodynamics and thermodynamic efficiencyLTECEng SwanseaUni
This document contains information from a thermodynamics lecture on heat engines and the laws of thermodynamics. It discusses key concepts like system boundaries, heat vs work, the first law of conservation of energy, and the second law regarding the direction of energy transfer and limits on converting heat fully to work. Examples are provided comparing performance of car engines and jet engines. Students are given a problem calculating properties of a jet engine experiment. The maximum theoretical fuel efficiencies of jet engines and all heat engines are discussed.
The document discusses thermal power cycles and the Rankine cycle in particular. It provides details on:
- The basic energy flow in a thermal power plant from chemical to mechanical to electrical energy.
- The Rankine cycle most closely models the steam power cycle used in most power plants. It involves heating water to steam to drive a turbine and then condensing the steam to recycle the water.
- Ways to improve the efficiency of the Rankine cycle include increasing the average temperature of heat addition by superheating steam or increasing boiler pressure, and decreasing the average temperature of heat rejection by lowering the condenser pressure.
Download Link (Copy URL):
https://sites.google.com/view/varunpratapsingh/teaching-engagements
Syllabus:
Availability and Irreversibility
Availability Function
Second Law Efficiencies
Work Potential Associated with Internal Energy
Waste Heat Recovery
Heat Losses – Quality vs. Quantity
Principle of Heat Recovery Units
Classification of WHRS on Temperature Range Bases
Commercial Viable Waste Heat Recovery Devices
Benefits of Waste Heat Recovery
Development of a Waste Heat Recovery System
Commercial Waste Heat Recovery Devices
West Heat Recovery Boiler (WHRB)
Recuperators- Regenerative, Ceramic, Regenerative Heat Exchanger
Thermal wheel/ Heat Wheel
Heat Pipe
Economiser
Feed Water
Heat Pump
Shell and Tube Heat Exchanger
Plate Heat Exchanger
Run-around coil
Direct Contact Heat Exchanger
Advantages and Limitations of WHRD’s
This document presents information on the Rankine cycle. It contains the following key points:
1. The Rankine cycle converts heat into work through a closed loop that uses water as the working fluid. It generates about 90% of the world's electric power.
2. An ideal Rankine cycle involves isothermal and isobaric processes, while a real cycle involves non-reversible and isentropic compression and expansion.
3. Variations like the reheat cycle and regeneration cycle can improve the efficiency by reheating steam before the turbine or preheating feedwater, but increase costs.
This document discusses the reheat cycle in thermodynamics. The reheat cycle is a modification of the Rankine cycle that is used in steam power plants. It works by reheating the steam after it expands in the high-pressure turbine and before it expands further in the low-pressure turbine. This increases the efficiency by raising the mean temperature of heat addition and reducing moisture content in the steam. Reheating allows for higher turbine work extraction and thermal efficiency compared to the basic Rankine cycle. The document examines the working of reheat cycles in steam turbines and thermal power plants, and their advantages in improving efficiency and reducing blade erosion.
This document discusses various thermodynamic cycles used in power generation applications including vapor power cycles, gas power cycles, and gas turbine cycles. It describes the basic processes and assumptions of cycles like the Rankine, Otto, diesel, and Brayton cycles. Methods to improve the performance of these cycles are also covered, such as increasing boiler pressure, superheating, reheating, and regeneration. The key applications of thermodynamics discussed are steam power plants, internal combustion engines, and gas turbine engines.
The document discusses Heat Recovery Steam Generators (HRSGs). HRSGs recover heat from gas turbine exhaust to produce steam. They operate in either combined cycle mode, where steam drives a turbine, or cogeneration mode where steam is used for industrial processes. HRSGs contain evaporator, economizer, and superheater sections to produce steam. They can also include reheaters, deaerators, and preheaters. HRSGs come in natural circulation, forced circulation, or once-through designs and can be unfired, fired, supplementary fired, or exhaust fired depending on heat input. HRSGs vary in operation pressure as either single or multi-pressure. Post-combustion emission controls like
This document provides an overview of various gas power cycles used in thermal engineering. It discusses the Otto, Diesel, dual, Brayton, and other cycles. For each cycle, it describes the key processes on P-V and T-S diagrams, such as isentropic compression and expansion and constant volume or pressure heat addition/rejection. It also provides the efficiency equations for ideal versions of the Otto, Diesel, and Brayton cycles. Real-world examples of engines using different cycles are given at the end.
Hrsg & turbine as run energy efficiency assessmentD.Pawan Kumar
The document provides measurements and performance data from an assessment of a heat recovery steam generator (HRSG) and steam turbine system. Key findings include:
- The HRSG achieved an overall thermal efficiency of 84.43% based on measured temperature and flow data.
- Heat was recovered across multiple components, with the high pressure evaporator recovering the most at 41.95% of total heat.
- The steam turbine achieved an overall efficiency of 78.40% based on measured steam and electrical output values.
The document provides information about the Brayton cycle used in gas turbines. It begins with an introduction to the Brayton cycle and gas turbines. It then describes the key components of a gas turbine system using the Brayton cycle, including the compressor, combustion chamber, and turbine. It also discusses the classifications of gas turbines as open cycle or closed cycle. Methods to improve the efficiency of the Brayton cycle like intercooling, reheating, and regeneration are covered. Applications of gas turbines and the advantages and disadvantages are summarized at the end.
This article investigates the thermal performance of a heat pipe heat exchanger for heat recovery in air conditioning applications. Experiments were conducted with ratios of return to fresh air mass flow rates of 1, 1.5, and 2.3. The fresh air inlet temperature was varied from 32°C to 40°C while the return air temperature was kept at 26°C. The results show that the temperature changes and effectiveness of both the evaporator and condenser sections increase with higher fresh air inlet temperatures. The enthalpy ratio between heat recovery and conventional air mixing also increases with fresh air inlet temperature, reaching 85% at 40°C.
This document provides lecture notes on gas power cycles from a mechanical engineering course. It covers the ideal gas relation, specific heats of gases, and the first law of thermodynamics as they relate to closed systems. Formulas are presented for the ideal gas law in various forms, as well as specific heat capacities for air. The notes also define important terms used in analyzing thermodynamic cycles, such as pressure ratio, compression ratio, and cutoff ratio. An example problem is included to demonstrate calculating maximum pressure, net specific work, and thermal efficiency for a diesel engine cycle.
This document analyzes the performance of different ocean thermal energy conversion cycles, including single-stage Rankine, double-stage Rankine, and Kalina cycles. It finds that double-stage Rankine and Kalina cycles, which use multiple heat exchangers or working fluid mixtures, can improve power output over a single-stage Rankine cycle by reducing irreversible losses during heat exchange. The analysis applies a simple method to evaluate temperature differences between working fluids and seawater in order to compare the system characteristics and effectiveness of reducing these losses across cycle types.
Review of enhancement for ocean thermal energy conversion system.pdfIreneKoronaki1
This document provides a review of enhancement strategies for ocean thermal energy conversion (OTEC) systems. It discusses various closed thermodynamic cycles that can be used in OTEC, including the basic Rankine cycle. Different working fluids are described, such as ammonia and ammonia-water mixtures, and how they affect cycle efficiency. The document also examines the impact of the ejector on cycle performance. Several methods to improve thermal efficiency are presented, such as intermediate extraction, heat recovery, reheating, and two-stage cycles. The most effective approaches are evaluated under identical operating conditions to determine which strategy provides the highest efficiency for OTEC.
OPTIMIZATION OF AN ORGANIC RANKINE CYCLE IN ENERGY RECOVERY FROM EXHAUST GASE...IAEME Publication
This paper describes thermal analysis and optimization of an organic Rankine cycle (ORC) integrated with a power generating stationary diesel engine. A simple ORC, with a regenerator, is considered here as a bottoming cycle for producing additional power by recovering waste energy
from the exhaust gases of the engine. Taking evaporation pressure and condensation temperature as two decision variables, a genetic algorithm is used for simultaneously maximizing three objective functions - exergy efficiency, thermal efficiency, and specific network.
POWER GENERATION BASED ON WASTE HEAT RECOVERYIRJET Journal
This document discusses power generation using waste heat recovery with the Kalina cycle. It begins with an introduction to the challenges of generating electricity from low-grade heat sources. The Kalina cycle is proposed as a solution, using ammonia and water as a working fluid that allows for heat recovery from flue gases. Simulation of the Kalina cycle was performed using Aspen Plus software. The simulation varied the ammonia fraction and calculated the generated power and efficiency. Previous studies on the Kalina cycle are also summarized that found it can increase efficiency over Rankine cycles for waste heat sources.
This document analyzes the performance of a transcritical refrigeration cycle (TRC) enhanced with a dedicated mechanical subcooling system. Three refrigerants are considered: CO2, N2O, and ethane. Results show that while N2O has the highest COP and exergy performance, CO2 has the best economic performance. Adding a subcooler improves the system COP by 30.74% for CO2, 26.48% for N2O, and 36.1% for ethane, while increasing the unit product cost by 9.04%, 8.37%, and 10.63%, respectively. The subcooling is deemed an effective and economical way to improve refrigeration system performance.
A description of how my optimization of carbon dioxide and propane mixture ratio as a working fluid helps reduce operating pressure by 33%, levelized cost of electricity (LCOE) by 6.36% and total power output from a diesel powered plant by 8% through waste heat recovery.
Seminar Report On OCEAN THERMAL ENERGY CONVERSIONAnik Samaddar
This document summarizes a seminar report on Ocean Thermal Energy Conversion (OTEC) presented by two students. It discusses the working principle of OTEC, which uses the temperature difference between warm surface water and cold deep ocean water to run a heat engine and generate electricity. There are two types of OTEC systems - closed-cycle which uses working fluids like ammonia, and open-cycle which uses seawater directly. OTEC plants can be land-based, floating, or offshore. The document provides a brief history of OTEC and discusses its future potential as a renewable energy source.
This document provides a seminar report on Ocean Thermal Energy Conversion (OTEC) presented by two students. It discusses the working principle of OTEC, which uses the temperature difference between warm surface ocean water and cold deep water to run a heat engine and generate electricity. It classifies OTEC plants as either closed-cycle or open-cycle, and as either land-based or floating/offshore. It then reviews the history of OTEC development from the 1880s to recent projects. The future potential of OTEC and its benefits are also mentioned.
วารสารวิชาการเทคโนโลยีพลังงานและสิ่งแวดล้อม บัณฑิตวิทยาลัย วิทยาลัยเทคโนโลยีสยาม
Journal of Energy and Environment Technology of Graduate School Siam Technology College
This paper describes an experimental study of using the waste heat from a Panasonic Under-
Ceiling split room air - conditioner had a rated capacity of 3.51 kW (12,000 Btu/h). An under – ceiling
split type air conditioning for heating domestic water in private homes. Energy recovery improved the
performance, and the recovered energy could replace electricity completely for heating domestic water
use. An extra charge of refrigerant in the air-conditioner could prevent its compressor from over heating
during energy recovery. The experimental conducted on varies capacity of the range from 22.5 litres to
120 litres storage tank. Results show the water temperature increased lies in the range of 50 OC to 65
OC. It was found that, when the initial water temperature in the 22.5 litres storage tank 27 OC, the water
temperature reached 65 OC in 105 minutes. For 120 litres water, temperature increased from 27 OC to 62
OC,5 in 240 minutes.
Effect of temperature on the performance of a closed-cycle ocean thermal ener...NUR FARAH
Ocean Thermal Energy Conversion (OTEC) is a process that can produce electricity by using the temperature difference between deep cold ocean water and warm tropical surface waters. OTEC pump large quantities of deep cold seawater and surface seawater to run a power cycle and produce electricity. There are 3 types of OTEC systems which are closed-cycle, open-cycle, and hybrid cycle. Solar thermal collector is used to heat up a fluid. Generally for water or a mixture of glycol and water depending of the configuration of the solar thermal system. The principles are to capture solar radiation, converting it to useful heat and transferring it to a working fluid.
Refrigeration and air conditioning (full note)shone john
Principles of refrigeration: Thermodynamics of refrigeration - Carnot cycle,
reversed carnot cycle, heat pump, and refrigerating machine- coefficient of
performance - unit of refrigeration - refrigeration methods- conventional
refrigeration systems. Air refrigeration system- Bell Coleman cycle - C.O.P.
capacity work and refrigerant flow requirements in Bell - Coleman cycle.
Module 2
Vapour compression system: simple cycle -comparison with Carnot cycle -
theoretical, actual and reactive - COP effect of operating parameters on
COP - wet, dry and superheated compression - under cooling - actual cycle
representation on TS and PH diagrams simple problems. Advanced
vapour compression systems - multistage vapour compression systems -
flash chamber multiple compression and evaporation systems cascading -
simple problems.
Module 3
Vapour absorption systems: simple, cycles - actual cycle - ammonia water
and lithium bromide water systems - COP - electrolux system. Refrigerant
and their properties: Nomenclature - suitability of refrigerants for various
applications - unconventional refrigeration methods- Vortex tube, steamjet, magnetic (cryogenics) refrigeration and thermoelectric refrigeration -
applied refrigeration house hold refrigerators - unit air conditioners andModule 4
Refrigeration system components: condensers - water and air cooled
condensers - evaporative condensers - expansion devises - capillary tubeconstant pressure expansion valve - thermostatic expansion valve - float
valve and solenoid valve - evaporators - natural convection coils - flooded
evaporators - direct expansion coils. Reciprocating compressors: single
stage and multistage compressors - work done optimum pressure ratioeffect of interfolding - volumetric efficiency -effect of clearance -
isothermal and adiabatic efficiency - compressed air motors. Rotodynamic
compressors: Screw and vane type compressors - principle of operation -
hermetic, semihermetic and open type refrigeration compressors.
Module 5
Principles of air conditioning: Psychrometry and psychrometric chart
thermodynamics of human comfort - effective temperature - comfort chart
applied psychrometry - sensible heat factor - psychometric processproblems. Winter air conditioning: heating load calculations humidifiers
and humidistat. Summer air conditioning: cooling load calculations - year
round air conditioning - unitary and central systems - principles of air
distribution - design of air duct systems.
References
1. Refrigeration and air conditioning - Ballaney P. L.
2. Refrigeration and air conditioning - Stocker W. F.
3. Refrigeration and air conditioning - Jordan and Protester
4. Principles of Refrigeration - Roy J. Dossat
Ocean thermal energy conversion (OTEC) harnesses the temperature difference between warm surface waters and cold deep ocean waters to generate electricity. The tropical oceans have about a 20°C difference between these waters that can power an OTEC system. OTEC systems pump warm surface water and cold deep water through a heat exchanger and turbine to produce electricity with minimal environmental impact. While capital costs are high currently, OTEC has potential for baseload renewable power due to the constant solar heating of ocean waters.
This document discusses waste heat recovery through the use of a reverse refrigeration cycle or organic Rankine cycle (ORC). It begins by outlining the problem of inefficient production processes that lose a significant amount of heat. The document then provides an overview of how a reverse refrigeration cycle works using a lower boiling point fluid to convert low-temperature waste heat into electricity. It discusses some key components of the cycle like the evaporator, turbine, condenser and pump. The document outlines the methodology that will be used to analyze implementing a reverse refrigeration cycle for waste heat recovery, including specifying the problem, evaluating heat sources, selecting a working fluid, calculating the ideal cycle, sizing heat exchangers, and calculating the real cycle
The document describes a water cooling system that uses engine exhaust heat from a two-wheeler engine. The system uses an adsorber bed filled with activated carbon to adsorb R134a refrigerant. Exhaust from the engine passes through the adsorber bed, heating it and causing the refrigerant to evaporate. The evaporated refrigerant then passes through a coil that acts as an evaporator, cooling water passed through it. After condensing, the refrigerant is expanded through a valve and re-adsorbed in the bed, completing the cycle. Experimental results showed the system could cool 2 liters of water to 19°C within 30 minutes, using only waste heat from the engine exhaust. The system provides
Ocean thermal energy conversion utilizes the temperature difference between warm surface waters and cooler deep ocean waters to generate electricity. It has the potential to be a renewable source of energy. The document discusses the types of ocean energy including ocean thermal energy. It describes the components and working of open and closed cycle OTEC systems and their applications in producing electricity, freshwater, refrigeration, and mineral extraction. The efficiency of OTEC plants depends on the temperature difference between the source and sink waters. While renewable, OTEC also has disadvantages such as high capital costs and low conversion efficiency.
This document presents a theoretical and experimental analysis of a direct-fired double effect lithium bromide/water absorption chiller located at a lighting technology company in Egypt. The chiller has a cooling capacity of 500 tons and uses a parallel flow configuration. Temperature measurements were taken at various points in the chiller components in July 2013 and July 2014. Mathematical equations were developed to model the chiller and estimate the coefficient of performance and heat transfer rates based on temperature and flow rate data. Theoretical and experimental analyses were conducted to evaluate how the COP is affected by factors like heat exchanger effectiveness and circulation ratio. The results show that the chiller's COP was lower in 2014 compared to 2013, possibly due to degradation of the heat ex
performance analysis of steam power plants using ideal reheat rankin cycleIJAEMSJORNAL
In this paper, a hypothetical examination has been done to assess the execution of the power plants that are chipping away at Reheat-Rankin cycle. The execution of cycle was dissected for various (warm, evaporator, condenser weights) values and also warm temperature qualities to demonstrate its impact on cycle warm proficiency. In this work, the heater weights qualities was accepted limited between (10to 26 MPa), the pressure proportion (warm stage weight to evaporator weight) was expected fluctuated in wide range from (0.1 to 1.0), while the condenser weight was accepted shifted between (5 to 25 kPa). And, a variety in warm temperature esteem was done between scopes of (400-600oC) at low weight turbine. The outcomes demonstrate that the warm productivity is considerably upgraded when the pressure proportion lies between (0.25-0.35) and the ideal proficiency is gotten when the pressure proportion and evaporator weight are equivalent to( 0.33 and 26MPa) separately .
This PowerPoint presentation discusses electricity production in thermal power plants using the Rankine cycle. It explains the basic processes involved in the Rankine cycle, including isentropic compression, constant pressure heat addition, isentropic expansion, and constant pressure heat rejection. Modifications to the Rankine cycle like reheat cycles and regenerative cycles are also presented. The document then discusses the organic Rankine cycle, which uses organic working fluids to recover heat from lower temperature sources. Key advantages of the organic Rankine cycle include higher efficiency and the ability to generate electricity from renewable sources like biomass, geothermal, and waste heat. Specific applications of organic Rankine cycle units in solar, biomass, geothermal, and waste heat
Review of Modified Vapor Absorption Refrigeration CyclesIRJET Journal
This document reviews various modifications made to vapor absorption refrigeration cycles to improve their performance. It discusses cycles that use an ejector, generator-absorber heat exchanger, booster compressor, or multiple absorption stages. The ejector cycle is found to have a 30% higher COP than a single-effect cycle. Generator-absorber heat exchanger cycles like the hybrid GAX cycle can achieve a COP as high as 0.98. A cycle with a booster compressor between the evaporator and absorber reaches a maximum COP of 0.645. The triple effect cycle demonstrates up to 132% higher COP than a single effect cycle. In general, modified cycles offer benefits like reduced losses, increased performance, and decreased energy consumption
Similar to Energy and Exergy Analysis of a Cogeneration Cycle, Driven by Ocean Thermal Energy Conversion (OTEC) (20)
Batteries -Introduction – Types of Batteries – discharging and charging of battery - characteristics of battery –battery rating- various tests on battery- – Primary battery: silver button cell- Secondary battery :Ni-Cd battery-modern battery: lithium ion battery-maintenance of batteries-choices of batteries for electric vehicle applications.
Fuel Cells: Introduction- importance and classification of fuel cells - description, principle, components, applications of fuel cells: H2-O2 fuel cell, alkaline fuel cell, molten carbonate fuel cell and direct methanol fuel cells.
Advanced control scheme of doubly fed induction generator for wind turbine us...IJECEIAES
This paper describes a speed control device for generating electrical energy on an electricity network based on the doubly fed induction generator (DFIG) used for wind power conversion systems. At first, a double-fed induction generator model was constructed. A control law is formulated to govern the flow of energy between the stator of a DFIG and the energy network using three types of controllers: proportional integral (PI), sliding mode controller (SMC) and second order sliding mode controller (SOSMC). Their different results in terms of power reference tracking, reaction to unexpected speed fluctuations, sensitivity to perturbations, and resilience against machine parameter alterations are compared. MATLAB/Simulink was used to conduct the simulations for the preceding study. Multiple simulations have shown very satisfying results, and the investigations demonstrate the efficacy and power-enhancing capabilities of the suggested control system.
Using recycled concrete aggregates (RCA) for pavements is crucial to achieving sustainability. Implementing RCA for new pavement can minimize carbon footprint, conserve natural resources, reduce harmful emissions, and lower life cycle costs. Compared to natural aggregate (NA), RCA pavement has fewer comprehensive studies and sustainability assessments.
ACEP Magazine edition 4th launched on 05.06.2024Rahul
This document provides information about the third edition of the magazine "Sthapatya" published by the Association of Civil Engineers (Practicing) Aurangabad. It includes messages from current and past presidents of ACEP, memories and photos from past ACEP events, information on life time achievement awards given by ACEP, and a technical article on concrete maintenance, repairs and strengthening. The document highlights activities of ACEP and provides a technical educational article for members.
DEEP LEARNING FOR SMART GRID INTRUSION DETECTION: A HYBRID CNN-LSTM-BASED MODELgerogepatton
As digital technology becomes more deeply embedded in power systems, protecting the communication
networks of Smart Grids (SG) has emerged as a critical concern. Distributed Network Protocol 3 (DNP3)
represents a multi-tiered application layer protocol extensively utilized in Supervisory Control and Data
Acquisition (SCADA)-based smart grids to facilitate real-time data gathering and control functionalities.
Robust Intrusion Detection Systems (IDS) are necessary for early threat detection and mitigation because
of the interconnection of these networks, which makes them vulnerable to a variety of cyberattacks. To
solve this issue, this paper develops a hybrid Deep Learning (DL) model specifically designed for intrusion
detection in smart grids. The proposed approach is a combination of the Convolutional Neural Network
(CNN) and the Long-Short-Term Memory algorithms (LSTM). We employed a recent intrusion detection
dataset (DNP3), which focuses on unauthorized commands and Denial of Service (DoS) cyberattacks, to
train and test our model. The results of our experiments show that our CNN-LSTM method is much better
at finding smart grid intrusions than other deep learning algorithms used for classification. In addition,
our proposed approach improves accuracy, precision, recall, and F1 score, achieving a high detection
accuracy rate of 99.50%.
Literature Review Basics and Understanding Reference Management.pptxDr Ramhari Poudyal
Three-day training on academic research focuses on analytical tools at United Technical College, supported by the University Grant Commission, Nepal. 24-26 May 2024
Harnessing WebAssembly for Real-time Stateless Streaming PipelinesChristina Lin
Traditionally, dealing with real-time data pipelines has involved significant overhead, even for straightforward tasks like data transformation or masking. However, in this talk, we’ll venture into the dynamic realm of WebAssembly (WASM) and discover how it can revolutionize the creation of stateless streaming pipelines within a Kafka (Redpanda) broker. These pipelines are adept at managing low-latency, high-data-volume scenarios.
KuberTENes Birthday Bash Guadalajara - K8sGPT first impressionsVictor Morales
K8sGPT is a tool that analyzes and diagnoses Kubernetes clusters. This presentation was used to share the requirements and dependencies to deploy K8sGPT in a local environment.
Manufacturing Process of molasses based distillery ppt.pptx
Energy and Exergy Analysis of a Cogeneration Cycle, Driven by Ocean Thermal Energy Conversion (OTEC)
1. The International Journal of Engineering and Science (IJES)
|| Volume || 6 || Issue || 3 || Pages || PP 32-41 || 2017 ||
ISSN (e): 2319 – 1813 ISSN (p): 2319 – 1805
DOI: 10.9790/1813-0603022131 www.theijes.com Page 32
Energy and Exergy Analysis of a Cogeneration Cycle, Driven by
Ocean Thermal Energy Conversion (OTEC)
Jeffrey Ofosu-Adarkwa1
, Tang Hao2
1
College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics Nanjing
210016, China
2
College of Energy and Power Engineering, Nanjing University of Aeronautics and Astronautics Nanjing
210016, China
--------------------------------------------------------ABSTRACT-----------------------------------------------------------
Ocean Thermal Energy Conversion (OTEC) is a technology by which thermal energy from the ocean is
harnessed and converted into electricity. It is one of the renewable energy technologies being researched into,
as part of solutions to the challenge of global warming and climate change. A major setback of this technology,
however, is that it has a very low cycle efficiency. In this work a cogeneration cycle is proposed which is driven
by the temperature difference between the warm surface layer and the cold bottom layer of the ocean. The work
is aimed at improving the overall cycle efficiency of OTEC systems by reducing the depth at which cold water is
captured from the ocean. To achieve this, the cycle employs a binary mixture of ammonia and water as the
working fluid and uses the mechanism of absorption to obtain the liquid phase of the working fluid after
expansion through the turbine. The effects of varying cycle parameters such as the depth of cold-water capture,
heat source temperature and mixture composition of the working fluid were investigated. With a basic solution
mixture concentration of 0.40 kg/kg NH3/H2O, and under operating conditions of 30o
C as the warm surface
water temperature and a cold water temperature of 10o
C, captured at a depth of 600m the proposed cycle
produced a net power output of 42 kW, and a refrigeration capacity of 370 kW. The thermal efficiency computed
was 1.94% and the exergy efficiency was 13.78%, both higher than the case where the depth of cold water
capture was 1000m.
Keywords – cogeneration, combined cooling and power, efficiency, exergy, OTEC, vapor absorption cycles
-------------------------------------------------------------------------------------------------------------------------------------
Date of Submission: 12 March 2017 Date of Accepted: 31 March 2017
--------------------------------------------------------------------------------------------------------------------------------------
I. INTRODUCTION
The primary source of power generation in the world
today is derived from the combustion of fossil fuels
such as oil, coal and natural gas. Increasing global
population and technological advancement have lead
to an ever-increasing energy demand. An adverse
effect of the burning of fossil fuels is the emission of
gases which are harmful to the environment. As a
consequence, global warming has increased in the last
decade. As a result, there have been frantic efforts
from a wide range of stakeholders, from scientists to
politicians to curb the situation and reduce the impact
of global warming and climate change. These
developments have lead to the intensification of
investigation of alternative energy resources and
technologies which produce very little or zero
emissions that contribute to global warming. Ocean
Thermal Energy Conversion (OTEC) is one of the
renewable technologies which is increasingly gaining
worldwide recognition. OTEC is a renewable energy
technology that converts heat energy into electricity
and other useful forms by making use of the
temperature difference between the warm upper
surface layer and the cold bottom layer of the ocean.
The OTEC technology employs the thermodynamic
concept of placing a heat engine between two
reservoirs (hot and cold), such that the hot reservoir
supplies heat to a thermodynamic cycle which
produces work and then rejects the heat to the cold
reservoir. In the case of OTEC, the upper layer (about
100m deep) of the ocean at a temperature of
approximately 25-30o
C serves as the heat source (hot
reservoir) and cold water drawn from the bottom of
the ocean (about 700 – 1000 m deep) at a temperature
of approximately 5-10o
C serves as the heat sink (cold
reservoir)[1]. The ability of this technology to achieve
power generation with thermal energy from the ocean
without the burning of any fuel is what makes it very
appealing especially with respect to environmental
impact, and the use of a constantly renewable
resource. However, a major setback of OTEC
technology is that, the temperature difference ∆T,
between the surface layer and the bottom layer of the
ocean, which is the driving force for OTEC, is very
small (~20o
) and as such leads to a very low thermal
efficiency, which is a constraint to its economic
viability[1].
2. Energy and Exergy Analysis of a Cogeneration Cycle, Driven by Ocean Thermal Energy Conversion
DOI: 10.9790/1813-0603022131 www.theijes.com Page 33
The basic configuration of a closed-cycle OTEC
system operates on the same principle of the Rankine
Cycle which is operated by conventional steam-driven
thermal power plants. The difference lies in the
operating temperatures. Whereas steam thermal plants
require a heat source temperature of over 100o
C to
operate efficiently, the heat source temperature for
OTEC is just about 25o
C to 30o
C supplied by the
surface layer of the ocean. As a result of this operating
temperature, the suitable working fluids for OTEC are
organic fluids and other working fluids which have
low saturation temperatures. Thus the thermodynamic
cycle that is usually operated by closed cycle OTEC
systems is the Organic Rankine Cycle. Sun et al.[2]
performed an exergy analysis and evaluated the cycle
performance, comparing results for an OTEC-driven
Organic Rankine Cycle, in which R717 and R134a
were used as the working fluids. the cycle was
optimized to achieve maximum net power output and
the working fluid R717 produced highly desirable
results as the most suitable working fluid. an
experimental study of the closed-cycle OTEC system
was carried out by Faizal and Ahmed[3].Results from
their study indicated a maximum thermal efficiency of
approximately 1.5% when R134a was used as the
working fluid. The net power output and efficiency
increased proportionally with the ratio of warm water
to cold water flowrates. Their study also pointed out
that both the thermal efficiency and the power output
of the system increased by increasing the temperature
difference between warm and cold seawater. One way
of increasing this temperature difference is by
increasing the temperature of the heat by using solar
heat energy [4, 5] and the waste heat from the
condenser of existing thermal power plants.
Another technique that is effective in improving cycle
efficiency involves the integration of other
components such as a regenerator to the cycle to
maximize the utilization of the available heat resource.
Wang et al.[6] carried out experiments using a
regenerative ORC system with R-123 as the working
fluid and geothermal heat source at 130o
C, and
compared the performance to that of a basic ORC
system. The results showed that the regenerative
system had an efficiency about 1.3 times higher than
that of the basic ORC.
Further improvements to the organic rankine cycle
lead to the development of other thermodynamic
cycles such as the Kalina cycle and the Goswami
cycle. The main distinguishing feature of the Kalina
cycle is the use of a binary mixture as the working
fluid. The advantage of a binary mixture working fluid
is that the phase transitions during the evaporation and
condensation process occur at a variable range of
temperatures. The individual boiling and condensation
temperatures of the mixture components are different,
and as such, during evaporation at a constant pressure
and a particular composition, the more volatile
component starts to vaporize. The vaporization starts
from the saturation temperature of the more volatile
component and then continues through to the
saturation temperature of the less volatile component.
This creates what is referred to as a temperature glide
and provides a better thermal matching between the
heat source and the working fluid. This reduces the
heat transfer irreversibility, thereby contributing to
improved cycle thermal efficiency. The use of binary
mixture working fluids in absorption power cycles
such as the Maloney-Robertson cycle and the Kalina
cycle, as well as vapor-absorption refrigeration cycles
inspired a new type of combined power and cooling
cycle, proposed by Dr. Yogi Goswami. In the
Goswami cycle, the feed stream of the working fluid is
obtained through absorption of the vapor by a liquid
solution rather than the usual type of condensation
used in conventional cycles. When the usual mode of
condensation is used, the minimum pressure and
temperature at which the expanding vapor exits the
turbine is limited by the temperature at which
condensation occurs for the working fluid. On the
other hand, when absorption-condensation is used, the
vapor exiting the turbine can be expanded to
temperatures below ambient pressure, with
corresponding low temperatures, without necessarily
being limited by the condensing temperature, resulting
in very cool vapor. This technique when applied to
OTEC systems would provide the benefit of not
having to go as deep as 1000m for cold deep seawater.
In essence, pumping cold deep seawater from as deep
as 1000m consumes a very large amount of the energy
produced (about one-third) and also requires
equipment which come at very huge costs. This work
presents a cogeneration cycle that will reduce the
depth of cold water capture, which will in effect
reduce pump energy consumption and improve overall
cycle efficiency.
II. MATERIALS AND METHODS
1.1 Modelling of Proposed Cycle
A model of the proposed cycle was simulated to
provide a basis for the evaluation of the various
performance indicators of the system. The simulation
was performed using ASPEN Plus®, which is a
commercial computer program that is used to model
thermodynamic processes. The properties of the
ammonia-water mixture and other fluids used in this
study were obtained from the NIST database which is
also available on the ASPEN Plus® program. The
fluid properties were also verified from REFPROP®
and the Soave-Redlich-Kwong (SRK) Equation of
State was employed as the property method.
3. Energy and Exergy Analysis of a Cogeneration Cycle, Driven by Ocean Thermal Energy Conversion
DOI: 10.9790/1813-0603022131 www.theijes.com Page 34
Figure 1 A schematic diagram of the proposed cogeneration cycle
A schematic diagram of the proposed cycle
configuration is shown in Fig.1. It can be described as
a combination of a vapor absorption power cycle and
a vapor absorption refrigeration cycle. The system is
controlled by two pressure levels i.e. the high pressure
at the boiler and the low pressure at the absorber. The
high pressure and the low pressure represent the
pressures at which the phase transition processes of
vaporization and condensation take place respectively.
The cycle begins with a mixture of ammonia and
water (NH3/H2O) with a specific composition. This is
referred to as the basic solution (state 1). A solution
pump is used to increase its pressure to the system
high pressure (state 2). This stream then passes
through an internal heat exchanger (IHE) where it
recovers heat from the weak solution (state 41) that
returns from the separator after the separation of rich
NH3 vapor. The preheated stream (state 3) goes
through the boiler, where it is boiled by the heat
source which is the surface sea water. Partial
vaporization occurs in the boiler, which results in a
two-phase, vapor-liquid mixture (state 4), which is
then further separated in the separator. The separation
process results two streams. One is a vapor stream
which has a very high concentration of NH3 (state 5),
and the other is the weak solution (state 41). The weak
solution is throttled to the system low pressure and
subsequently to the absorber.
The rich NH3 vapor on the other hand, is split into two
streams, (state 51) and (state 6). The stream with
parameters as at state 6 is the stream that drives the
power generation part of the cycle. It is expanded to
low pressure (state 7) through the turbine, thereby
generating a power output. The other NH3-rich vapor
stream (state 51), on the other hand drives the
refrigeration part of the combined cycle. It is first
condensed (state 52) after which it is throttled to the
system low pressure (state 53). At this state it is very
cold liquid which serves as the refrigerant when
passed through an evaporator. At the evaporator, the
cold sea water which has a relatively higher
temperature than the ammonia-rich refrigerant is made
to provide sensible heating to vaporize the ammonia-
rich refrigerant (state 54). The vapor streams (state 7)
and (state 54) mix together and are absorbed by the
weak solution (state 43) to reform the basic solution
(state 1) in the absorber.
1.2 Mass and Energy Balance
The simulation of the proposed cycle and the
subsequent thermodynamic analyses are based on
energy and mass balance equations as well as
assumption of certain conditions which simplify the
equations. The key operating conditions and
assumptions that were made with respect to the
simulation of the proposed cycle are as follows.
Energy and mass balance calculations are done on the
components by taking each component as a control
volume under steady state operation. The conditions
for boiling are specified by entering boiling
temperature, pressure, and basic solution
concentration as inputs. The minimum absorption
temperature and the concentration of the basic
solution are also specified. The pump and turbine are
assumed to have isentropic efficiencies of 0.85 each,
and heat losses and pressure drops are neglected. The
reference temperature, To is taken to be 298.15 K. The
mass balance and energy balance equations are
represented by the equations (1) – (12).
(1)
(2)
(3)
(4)
(5)
(5)
(6)
4. Energy and Exergy Analysis of a Cogeneration Cycle, Driven by Ocean Thermal Energy Conversion
DOI: 10.9790/1813-0603022131 www.theijes.com Page 35
(7)
(8)
(9)
(10)
(11)
(12)
1.3 Performance Evaluation of Cogeneration
Cycle
Since the output of the combined cycle consists of two
different quantities, i.e. power and refrigeration,
whose efficiencies are computed differently.
Evaluating the efficiency of the combined cycle
simply as a ratio of the sum of outputs to the heat
input would be erroneous and would overestimate the
efficiency of the cycle. In order to address this issue,
Vijayaraghavan and Goswami [7] developed new
expressions which are more appropriate and
thermodynamically consistent in representing the
efficiency of the combined power and cooling cycle.
These new expressions account for the quality of heat
available for the refrigeration part of the cycle. This is
accomplished by replacing the cooling output of the
cycle by the exergy associated with the cooling output,
thus making it possible to add the refrigeration output
to the power output in a single efficiency expression
as follows:
(13)
(14
)
(15
)
The performance of the combined cycle can be
evaluated consistently using the expressions in (13)
and (14). However, these definitions, in themselves
are not appropriate when we need to compare the
combined cycle to other thermodynamic cycles. For
instance, to compare this combined cycle to a power
cycle, we would have to configure the combined cycle
to operate as a power cycle, and as such, the
refrigeration output would have to be weighted
differently in order to be able to make a valid
comparison. One way to achieve this, is by dividing
the exergy of cooling by the COP of a reversible
refrigeration cycle, which is a Lorentz cycle in this
case. This implies replacing the cooling output by the
minimum mechanical power required to produce the
same amount of cooling that would be achieved by a
reversible refrigeration cycle. The resulting
expression, as reported by Vijayaraghavan and
Goswami, is referred to as effective efficiency, shown
below [8-10]:
(16)
(17)
In practical applications, however, the same cooling
output would require relatively higher amount of
power input due to certain internal and external
irreversibilities associated with real refrigeration
cycles. A more realistic approach would be to divide
the exergy of cooling by a reasonable second law
efficiency for a refrigeration cycle. This is equivalent
to dividing by a practical COP rather than the
reversible COP.
1.4 Exergy Analysis
Exergy analysis was performed on the combined cycle
in order to determine the sources of irreversibility
which leads to losses in the cycle. This was done by
modelling each component as a control volume and
then using the exergy balance equation to calculate the
exergy destruction (irreversibility) for each
component. The exergy destroyed represents the
energy that could have been converted to work but
was rather wasted, thus it is desirable to keep the
exergy destroyed as minimal as possible. The
determination of the exergy destruction at various
components of the cycle is important as it points one
to aspects of the cycle that need to be improved in
order to reduce losses and improve the overall
efficiency of the cycle. The overall exergy balance is
expressed by the equation:
(18)
The term To (Sgen ) ̇ is what is termed the
irreversibility or the exergy destroyed and is denoted
Ed, for purposes of this study. The exergy destroyed at
the various components of the system were computed
from simplifying the above expression (18) using the
assumptions listed in section 2.2. for the
thermodynamic analysis.
III. RESULTS AND DISCUSSION
1.5 Effect of Heat Source Temperature
In the basic configuration of the proposed cycle, the
heat source which is warm surface seawater is
supplied to the evaporator at an inlet temperature of
25o
C. However, this inlet temperature can be
increased by other techniques such as using solar
collectors or using effluent heat streams from existing
thermal plants as mentioned previously. Simulations
were performed to evaluate the cycle’s performance
and observe the effect of increasing the heat source
temperature. The key operating conditions that were
used in simulating the proposed cycle are summarized
in Table 1. These simulations were done with the
assumption that the temperature of the warm sea water
was increased to 30, 35 and 40o
C, by one of the
techniques mentioned earlier. The results produced
are summarized in Table 2 and shows an increasing
5. Energy and Exergy Analysis of a Cogeneration Cycle, Driven by Ocean Thermal Energy Conversion
DOI: 10.9790/1813-0603022131 www.theijes.com Page 36
trend for the cycle’s performance as the heat source
temperature increased. A plot to illustrate this
relationship is shown on Fig. 2. The work output (net
power) as well as the cooling output increased as the
heat source temperature was increased.
Table 1 Summary Of Operating Conditions for
Simulation
Parameter Unit Value
Reference Temperature (To)
Evaporator pressure (PEVAP)
Absorber pressure (Pabs)
Mass flowrate of working fluid (m)
Ammonia mass fraction (X) of basic
solution
Warm water inlet temperature (Tww)
Cold water inlet temperature (Tcw)
Pump Isentropic efficiency
Turbine Isentropic efficiency
K
bar
bar
kg/s
kg/kg
NH3
o
C
o
C
298.1
5
8.0
5.0
10
0.40
30
10
0.85
0.85
Table 2 Cycle Performance Summary at Heat Source
Temperature of 30o
C
Parameter Unit CASE I CASE II
Depth of Ocean m 1000 600
Turbine Work output
(W)
kW 137 137
Pump work (Wpump) kW 134 95
Net Power output
(Wnet)
kW 3 42
Refrigeration output
(Qc)
kW 370 370
Exergy of Cooling
(Ec)
kW 26 26
Evaporator Heat
input (Qh)
MW 3.5 3.5
Exergy at evaporator
(Ehs)
kW 534 534
Thermal efficiency
( )
% 0.38 1.94
Exergy efficiency
( )
% 3.81 13.78
Figure 2 Effect of The Heat Source Temperature on
The Cycle Outputs
1.6 Effect of Mixture Composition
A very important characteristic for all binary-mixture
working fluids is the concentration of the mixture.
This characteristic has a direct impact on the
saturation temperatures as well as the temperature
glide of the working fluid. As has been explained in
the previous sections, the construction of the bubble
and dew point lines, which represent the phase
transition from the liquid state to the vapor state and
vice versa, depend on the concentration of the mixture
and the pressures at which the process take place.
Similar to the pressure at which boiling occurs, the
mixture concentration has lower and upper limits. The
lowest possible concentration corresponds to the
concentration that saturation occurs at the given
temperature and pressure. This implies that a mixture
having a concentration below the lower limit will not
be able to boil at the specified temperature. In a
similar manner, the concentration of the basic solution
determines the absorption pressure. At a point where
the saturation pressure becomes equal to the boiling
pressure, the mixture concentration would have
attained its maximum value.
For this study, the concentration of the basic solution
was varied from 0.36 to 0.50 kg/kg NH3/H2O. The
simulation results indicated a general increase in the
cycle outputs as the composition of ammonia in the
mixture was varied incrementally from 0.36. This is
mainly due to the fact that increasing the mass fraction
of ammonia in the mixture implies increasing the mass
fraction of the more-volatile substance. Since the
more-volatile substance has a lower boiling point, the
higher its composition, the higher the amount of vapor
that is formed (Fig. 3 and Fig. 4), and since it is the
formation of the vapor that drives the cycle’s outputs,
the increase in the formation of vapor corresponds to
an increase in the cycle outputs.
Figure 3 Effect of Mixture Concentration on The
Cycle Outputs
6. Energy and Exergy Analysis of a Cogeneration Cycle, Driven by Ocean Thermal Energy Conversion
DOI: 10.9790/1813-0603022131 www.theijes.com Page 37
Figure 4 Effect of Composition on The Vapor
Fraction at Varying Heat Source Temperatures
1.7 Pump Power Input
Two cases were simulated with respect to the depth of
the ocean and their performance characteristics were
evaluated. Case I represented the situation where the
cold water is captured at a depth of 1000m beneath the
ocean surface. This depth corresponded to a cold
water temperature of approximately 5o
C. Case II on
the other hand represented the situation whereby the
proposed cogeneration cycle makes it possible for the
depth of cold water capture to be reduced to 600m
beneath the ocean surface layer. Comparison between
the simulation results of these two cases indicated that
Case II produced higher net power outputs and cycle
efficiencies than Case I. This is explained by Fig. 5
which shows the effect of the depth of cold water
capture on the power input required by the pump. The
figure is plotted from (19) and shows a directly
proportional relationship between the ocean depth and
the power required to pump water from the
corresponding depth to the ocean surface layer where
the OTEC plant is installed.
6
3 .6 * 1 0
h
q g h
P
(19)
Where Ph is the hydraulic power in kilowatts (kW), q
is the flow capacity in cubic meters per hour (m3
/h), ρ
is the density of water in kilograms per cubic meters
(kg/m3
), g is the acceleration due to gravity (9.81
m/s2
) and h is the ocean differential head in meters
(m).
Figure 5 Relationship between Ocean Depth of Cold
Water Capture and Pump Power Input
1.8 Effect of Split Fraction
The splitter serves the primary purpose of splitting the
ammonia-rich vapor into two streams which are the
driving forces behind the absorption power and the
absorption refrigeration parts of the cycle. Since the
cycle employs the use of a splitter to obtain the two
vapor streams, the split fraction that is used plays an
important role in determining how much power or
cooling output is obtained. As such, the split ratio was
varied according to a:b = 0.5:0.5, a:b = 0.4:0.6, a:b =
0.3:0.7, a:b = 0.2:0.8 and a:b = 0.1:0.9, where “a”
represents the fraction of vapor that goes to
refrigeration part and “b” represents the fraction of
vapor that goes to the power generation part. The
identifications SPL_F1, SPL_F2, SPL_F3, SPL_F4,
and SPL_F5 were given for the various split fractions
which correspond to 0.5:0.5, 0.4:0.6, 0.3:0.7, 0.2:0.8
and 0.1:0.9 respectively. The Fig. 6a shows that as the
fraction “a” which corresponds to the vapor set aside
for the refrigeration part decreased from 0.5 to 0.1, the
refrigeration output decreased.While “a” decreased,
“b” increased from 0.5 to 0.9 which corresponds to an
increase in the fraction of the vapor designated to
expand in the turbine to generate the power output.
This lead to an increase in the power output (Fig. 6b)
The optimum split ratio for the cycle was chosen to be
a:b = 0.1:0.9, since this ratio gave the maximum
power output.
7. Energy and Exergy Analysis of a Cogeneration Cycle, Driven by Ocean Thermal Energy Conversion
DOI: 10.9790/1813-0603022131 www.theijes.com Page 38
Figure 6 Effect of Split Fractions on The Cycle Outputs
1.9 Overall Cycle Efficiency
3.5.1 Thermal Efficiency
A very important parameter for every device that
makes use of thermal energy is the thermal efficiency,
ηth. Often referred to as “1st Law efficiency” or simply
efficiency, it is a straightforward representation of the
cycle’s performance based on the conditions of the
heat transfer mechanisms in the cycle’s heat
exchangers. For power cycles, it gives an indication of
the extent to which the heat energy provided to the
cycle is converted to the net work output. For
absorption refrigeration cycles, on the other hand, it
gives an indication of the amount of cooling that is
produced from the heat added to the cycle and is
referred to as the coefficient of performance (COP).
The thermal efficiency of the proposed combined
cycle was computed according to (13) and (15), using
results from the simulation. Different concentrations
of the basic solution of the binary mixture working
fluid were investigated to observe the effect on the
thermal efficiency. The heat source temperature was
also varied to observe the effect it has on the thermal
efficiency. Also, the trend for the thermal efficiency
was observed for different split fractions of the
ammonia-rich vapor. Fig. 7 shows that the thermal
efficiency of the cycle portrays a steady increase as
the heat source temperature increases. This is due to
the fact that there is an increase in the extent to which
vapor formation in the evaporator occurs when the
heat source temperature is increased.
3.5.2 Exergy Efficiency
A limitation of the first law (thermal) efficiency, is its
inability to reflect all the irreversible losses due to the
fact that it does not account for the quality of heat
through the cycle. The 2nd law of thermodynamics,
however, accounts for the increase in entropy that
takes place during temperature change. The increase
in entropy leads to irreversibility and as such lead to
energy losses in a process. The term exergy is a
consequence of the 2nd Law and refers to the
maximum useful work that is possible to be done by a
process that brings a system into equilibrium with a
heat reservoir. In this regard, exergy efficiency or
second law efficiency refers to a ratio of the desired
output to the useful input and thus a measure of the
fraction of the exergy going into the cycle that comes
out as useful output.
The expressions for the exergy efficiency of the
proposed combined cycle (14) and (15) were used to
compute the exergy efficiency using the results from
the simulation. The influence of cycle parameters such
as heat source temperature, basic solution
concentration and split fraction on the exergy
efficiency was investigated. When different heat
source temperatures were applied to the cycle, the
exergy efficiency increased with increasing heat
source temperature. In comparison with the thermal
efficiency, the exergy efficiency of the cycle indicated
higher values as expected (Fig.7). The influence of the
variation in concentration of the basic solution on the
exergy efficiency was also investigated. Fig. 8 shows
that as the composition is increased, the exergy
efficiency increases steeply until a concentration of
0.40 NH3, after which the increment is gradual. This is
mainly due the nature of the NH3-H2O enthalpy-
concentration diagram (Fig. 9). The figure shows that
at a fixed pressure, and with an increasing
concentration, the liquid enthalpy gradually decreases
initially, and then reaches a point of inflection where it
starts to increase. The initial compositions at which
there is a decrease in the enthalpy lead to a
corresponding decrease in the exergy of the heat
source (Ehs). From (14), since and are
inversely proportional, when the exergy change of the
heat source decreases, the exergy efficiency increases
and vice versa.
8. Energy and Exergy Analysis of a Cogeneration Cycle, Driven by Ocean Thermal Energy Conversion
DOI: 10.9790/1813-0603022131 www.theijes.com Page 39
Figure 7 Effect of The Heat Source Temperature on
The Cycle Efficiency
Figure 8 Effect of The Mixture Concentration on The
Exergy Efficiency of The Cycle
Figure 9 Effect of Enthalpy-Concentration Curves of
NH3/H2O Mixture (5 – 8 bar)
1.10 Exergy Analysis
The Exergy analysis performed on the combined cycle
enabled the determination of sources of irreversibility
in the cycle. Each component was assumed as a
control volume and then exergy balance equations
were used to calculate the exergy destruction
(irreversibility) for each component. Fig. 10 shows a
comparison between the exergy destruction rates of
the components of the proposed cogeneration system
and a conventional power cycle. As illustrated in the
chart, the highest rate of exergy destroyed is at the
turbine of the conventional power cycle. This can be
attributed to the fact that the working fluid which is
highly rich in NH3 in this case is not allowed to
expand to pressures below ambient conditions. That
would require extremely low temperatures for
condensation to occur. This situation is avoided at the
expense of the power output that could be produced if
the vapor were allowed to expand further to low
pressures. This contributes to a large amount of
exergy destruction. It can be seen that this is not the
case for the turbine in the cogeneration cycle, since
the process of absorption helps to deal with this issue.
The absorber is the component with the second
highest rate of exergy destruction, followed by the
evaporator. Generally, the components of the
cogeneration cycle contributed less to the total exergy
destroyed than those of the conventional power cycle.
The importance of exergy analyses with the
determination of the exergy destruction at various
components of the cycle is evident in the fact that it
highlights the parts of the cycle that generate very
high irreversibilities, such that if modifications need to
be made to improve the performance of the system,
those areas that contribute the highest irreversibilities
are the first places to look at.
Figure 10 Exergy Losses by Component
1.11 Comparison between the Proposed Cycle and
Conventional Absorption Power Cycle
A simulation of a conventional absorption power-only
cycle was performed to serve as a basis for
comparison with the proposed combined absorption
power and refrigeration cycle. In order to obtain a
more valid comparison, between these two different
types of cycles, the combined cycle would have to be
configured in such a way as to imitate operating as a
power cycle. This was easily achieved by dividing the
exergy of cooling by the COP of a reversible
refrigeration cycle, which is a Lorentz cycle in this
case. By so doing, we would be replacing the cooling
output by the minimum mechanical power required to
produce the same amount of cooling that would be
9. Energy and Exergy Analysis of a Cogeneration Cycle, Driven by Ocean Thermal Energy Conversion
DOI: 10.9790/1813-0603022131 www.theijes.com Page 40
achieved by a reversible refrigeration cycle. For non-
ideal situations, however, this is termed as the
practical COP since a reasonable COP rather than that
of the reversible refrigeration cycle is used. The
COPRev in equation 3.53 and equation 3.54 are
replaced by COP practical the effective efficiencies take
the form:
(20)
(21)
The equations (20) and (21) were used to obtain the
effective thermal efficiency and effective exergy
efficiencies of the combined cycle that provided a
more valid basis for comparison with the power-only
cycle. The results of effective thermal efficiency of the
combined cycle was compared to the thermal
efficiency of the power cycle based on parameters
such as varying heat source temperature, and
concentration of the basic solution. Fig.11 shows that
the cogeneration cycle gives higher thermal efficiency
than the power-only cycle, and this is the case for the
entire range of hat source temperatures that were
applied. Fig.12 also indicates that the exergy
efficiency for the combined cycle is higher than that of
the power cycle for all the heat source temperatures
that were applied.
Figure 11 Comparing the Thermal Efficiency of The
Cogeneration Cycle and A Power Cycle
Figure 12 Comparing the Exergy Efficiency of The
Cogeneration Cycle and A Power Cycle
IV. CONCLUSIONS
The minimum temperature difference (∆T) between
the warm surface and the cold bottom layers of the
ocean that is applicable to OTEC systems is 20o
. The
performance of OTEC systems is dependent on the
temperature of the heat source (warm surface sea
water) as well as the temperature of the cold reservoir
(cold sea water). The NH3/H2O mixture working fluid
makes it possible for absorption-condensation, which
in effect, makes it possible to obtain cold water at a
reduced depth of about 600m. The refrigeration output
of the cogeneration system makes it possible to
increase ∆T by providing further cooling at the
absorber. Two cases were presented with respect to
the depth of cold water capture. Case I and Case II
represented configurations of the OTEC-cogeneration
cycle in which the cold water is captured at 1000m
and 600m respectively. Under simulation conditions
of 30o
C warm surface sea water temperature, 10o
C
cold sea water temperature captured at a depth of
600m, and an optimum working fluid basic solution
concentration of 0.40 NH3/H2O Case II produced a net
power output of 31 kW and a refrigeration output of
360 kW. The thermal efficiency and exergy efficiency
under those conditions were 1.94% and 13.78%
respectively. Case I, on the other hand produced a net
power output of 3 kW with thermal efficiency of 0.4%
and an exergy efficiency of 3.8%. The low net power
output of the Case I cycle is attributed to the high rate
of energy consumption that accompanies the drawing
of cold water from the ocean depths, which reduces
the net power output of the cycle.
The temperature of the heat source was also varied
from 25o
C to 30o
C, 35o
C and 40o
C based on the
assumption that the temperature of the warm surface
sea water can be increased by using external methods
to heat up the warm sea water in order to achieve
higher cycle outputs. At a heat source temperature of
30o
C, the cycle for Case II produced a net power
output of 42 kW, a refrigeration output of 370 kW, a
10. Energy and Exergy Analysis of a Cogeneration Cycle, Driven by Ocean Thermal Energy Conversion
DOI: 10.9790/1813-0603022131 www.theijes.com Page 41
thermal efficiency of 1.87% and an exergy efficiency
of 13.69%. When the heat source temperature was
increased to 35o
C, the cycle produced a net power
output of 60 kW, a refrigeration output of 402 kW, a
thermal efficiency of 2.38% and an exergy efficiency
of 13.98%. Finally, at a heat source temperature of
40o
C, the cycle produced a net power output of 69
kW, a refrigeration output of 417 kW, a thermal
efficiency of 2.61% and an exergy efficiency of
14.91%. Although the thermal efficiency of OTEC
systems is generally low, it is important to take note
that seawater, which is the “fuel” which drives the
system, is virtually free. It is therefore, more
appropriate to evaluate the cycle’s performance using
the concept of exergy efficiency. The reason being
that an evaluation based on the concept of exergy
efficiency takes into consideration the availability of
the heat source i.e. the amount of thermal energy from
the warm surface sea water that is used up by the cycle
and not the entire heat input.
Nomenclature
Symbols
E Change in exergy, kW
Ec Change in exergy of cooling, kW
g Acceleration due to gravity, ms-2
h enthalpy, kJkg-1
h height, m
m mass, kg
Mass flow rate, kgs-1
p Pressure, bar
Ph Pump Hydraulic Power, kW
Q Heat transfer, kW
S Entropy, kJkg-1
K-1
T Temperature, o
C
To Absolute temp. of reference point, K
Wnet net power output, kW
Wp pump work input, kW
Subscripts
ABS Absorber
CW cold seawater
CWP cold seawater pump
EVAP evaporator
IHEX internal heat exchanger
REVAP refrigeration evaporator
SEP flash separator
SPL splitter
TURB turbine
VLV throttling valve
WFP working fluid pump
WW warm seawater
WWP warm seawater pump
REFERENCES
[1]. Masutani, S.M. and P.K. Takahashi, Ocean Thermal
Energy Conversion. Fuel and Energy Abstracts, 1999.
37(3): p. 201.
[2]. Faizal, M. and M.R. Ahmed, Experimental studies on a
closed cycle demonstration OTEC plant working on small
temperature difference. Renewable Energy, 2013. 51: p.
234-240.
[3]. Yang, M. and R. Yeh, Analysis of optimization in an
OTEC plant using organic Rankine cycle. Renewable
Energy, 2014. 68: p. 25-34.
[4]. Yamada, N., A. Hoshi, and Y. Ikegami, Performance
simulation of solar-boosted ocean thermal energy
conversion plant. Renewable Energy, 2009. 34(7): p.
1752-1758.
[5]. Bombarda, P., C. Invernizzi, and M. Gaia, Performance
Analysis of OTEC Plants With Multilevel Organic Rankine
Cycle and Solar Hybridization. Journal of Engineering for
Gas Turbines and Power-transactions of The Asme, 2013.
135(4): p. 042302.
[6]. Li, M., et al., Construction and preliminary test of a low-
temperature regenerative Organic Rankine Cycle (ORC)
using R123. Renewable Energy, 2013. 57: p. 216-222.
[7]. Vijayaraghavan, S. and D.Y. Goswami, On Evaluating
Efficiency of a Combined Power and Cooling Cycle.
Journal of Energy Resources Technology-transactions of
The Asme, 2003. 125(3): p. 221-227.
[8]. Ayou, D.S., et al., Analysis and simulation of modified
ammonia/water absorption cycle for power and cooling
applications. International Journal of Low-carbon
Technologies, 2013. 8.
[9]. Tamm, G., et al., Novel Combined Power and Cooling
Thermodynamic Cycle for Low Temperature Heat
Sources, Part I: Theoretical Investigation. Journal of Solar
Energy Engineering-transactions of The Asme, 2003.
125(2): p. 218-222.
[10]. Sadrameli, S.M. and D.Y. Goswami, Optimum operating
conditions for a combined power and cooling
thermodynamic cycle. Applied Energy, 2007. 84(3): p.
254-265.