Usually a STATCOM is installed to support power
system networks that have a poor power factor and often poor
voltage regulation. It is based on a power electronics voltagesource
converter. Various PWM techniques make selective
harmonic elimination possible, which effectively control the
harmonic content of voltage source converters. The distribution
systems have to supply unbalanced nonlinear loads transferring
oscillations to the DC-side of the converter in a realistic
operating condition. Thus, additional harmonics are modulated
through the STATCOM at the point of common coupling
(PCC). This requires more attention when switching angles are
calculated offline using the optimal PWM technique. This
paper, therefore, presents the artificial neural network model
for defining the switching criterion of the VSC for the
STATCOM in order to reduce the total harmonic distortion
(THD) of the injected line current at the PCC. The model takes
into the account the dc capacitor effect, effects of other possible
varying parameters such as voltage unbalance as well as
network harmonics. A reference is developed for offline
prediction and then implemented with the help of back
propagation technique.
Fuzzy Logic Controller Based High Frequency Link AC-AC Converter For Voltage ...IJTET Journal
Abstract—In this paper, an advanced high frequency link AC-AC Push-pull cycloconverter for the voltage compensation is proposed in order to maintain the power quality in electric grid. The proposed methodology can be achieve arbitrary output voltage without using large energy storage elements. So that the system is more steadfast and less costly compared with the conventional inverter topology. Additionally, the proposed converter does not contain any line frequency transformer, which reduces the cost further. The control scheme for the push pull cycloconverter employs the fuzzy logic controller based sinusoidal pulse width modulation (SPWM) to accomplish better performance on voltage compensation, like unbalanced voltage harmonics elimination. The simulation results are given to show the effectiveness of the proposed high frequency link AC-AC converter and fuzzy logic controller based SPWM technology
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Small Signal Modeling Of Controller For Statcom Used In Distribution System F...IJERA Editor
In this paper non-linear model of the STATCOM is linearized and the following strategies have been adopted .
Hence, a small signal model is adopted here. Here, the grid voltage lags the fundamental component of the
STATCOM converter terminal voltage with a phase angle difference
' '
. Small signal modeling of the phase
angle
' '
and modulation index
' m '
is also done. A single PI-controller for the reactive component current of
the STATCOM has been designed. In this model, the DC-link capacitor voltage is held constant without using a
separate controller. The STATCOM are designed using SVPWM technique. Through adjustment of the
modulation index, fast modulation of the STATCOM reactive power output can be achieved due to high
sensitivity of the same with respect to the output voltage of the STATCOM VSC. The model, with PI controllers
has been simulated in MATLAB/SIMULINK environment with variation of the pre-charge voltage on the DClink
capacitor with linear loads (inductive). Improvement of the power factor of the grid current is achieved for
linear loads.
Torque Ripple Minimization of a BLDC Motor Drive by Using Electronic Commutat...AI Publications
Brushless DC motors are having a major problem with harmonics in torque. The variations in speed and production of noise should be minimized by using proper topologies. BLDC motors have been gaining attention from different Industrial and domestic appliance manufacturers, because of their high efficiency, high power density and easy maintenance and low cost. This paper presents a three phase BLDC motor with low cost drive to be driven without DC link capacitor. The proposed technique uses an electronic commutation and operates the machine exclusive of the intermediate DC link capacitor. The designing of Brushless DC motor drive system along with control system for torque ripple minimization, speed controller and current controllers are presented using MATLAB / SIMULINK and results are evaluated.
Simulation of Five Level Diode Clamped Multilevel Inverterrahulmonikasharma
The power electronics device which converts DC power to AC power at required output voltage and frequency level is known as inverter. The voltage source inverters produce an output voltage or a current with levels either 0 or +ve or-ve V dc. They are known as two-level inverters. Multilevel inverter is to synthesize a near sinusoidal voltage from several levels of dc voltages. Multilevel inverter has advantage like minimum harmonic distortion. Multi-level inverters are emerging as the new breed of power converter options for high power applications. They typically synthesize the stair-case voltage waveform (from several dc sources) which has reduced harmonic content. Multi-level inverters have many attractive features, high voltage capability, reduced common mode voltages near sinusoidal outputs, low dv/dt, and smaller or even no output filter; sometimes no transformer is required at the input side, called the transformer-less solution, making them suitable for high power applications In this paper a 5-level Diode clamped multilevel inverter is developed by IGBTS using Simulink. Gating signals for these IGBTS have been generated by designing comparators. In order to maintain the different voltage levels at appropriate intervals, the conduction time intervals of IGBT have been maintained by controlling the pulse width of gating pulses[6] (by varying the reference signals magnitude of the comparator). The simulation results for 5-level and THD for the output have been identified by MATLAB/SIMULINK.
Simulation of D-STATCOM to study Voltage Stability in Distribution systemijsrd.com
This paper presents the simulation of D-statcom to understand the improvement of voltage stability [1] of distribution system. The power circuits of the D-STATCOM and distribution networks are made up of simpower system blocks, while the control circuits made with the simulink blocks The STATCOM is applied to regulate transmission voltage to allow greater power flow in a voltage limited transmission network, in the same manner as a static var compensator (SVC), the STATCOM has further potential by giving an inherently faster response and greater output to a system with depressed voltage and offers improved quality of supply. The main applications of the STATCOM are; Distribution STATCOM (D-STATCOM) exhibits high speed control of reactive power to provide voltage stabilization and other type of system control. The DSTATCOM protects the utility transmission or distribution system from voltage sag and /or flicker caused by rapidly varying reactive current demand. During the transient conditions the D-STATCOM provides leading or lagging reactive power to active system stability, power factor correction and load balancing.
Fuzzy Logic Controller Based High Frequency Link AC-AC Converter For Voltage ...IJTET Journal
Abstract—In this paper, an advanced high frequency link AC-AC Push-pull cycloconverter for the voltage compensation is proposed in order to maintain the power quality in electric grid. The proposed methodology can be achieve arbitrary output voltage without using large energy storage elements. So that the system is more steadfast and less costly compared with the conventional inverter topology. Additionally, the proposed converter does not contain any line frequency transformer, which reduces the cost further. The control scheme for the push pull cycloconverter employs the fuzzy logic controller based sinusoidal pulse width modulation (SPWM) to accomplish better performance on voltage compensation, like unbalanced voltage harmonics elimination. The simulation results are given to show the effectiveness of the proposed high frequency link AC-AC converter and fuzzy logic controller based SPWM technology
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Small Signal Modeling Of Controller For Statcom Used In Distribution System F...IJERA Editor
In this paper non-linear model of the STATCOM is linearized and the following strategies have been adopted .
Hence, a small signal model is adopted here. Here, the grid voltage lags the fundamental component of the
STATCOM converter terminal voltage with a phase angle difference
' '
. Small signal modeling of the phase
angle
' '
and modulation index
' m '
is also done. A single PI-controller for the reactive component current of
the STATCOM has been designed. In this model, the DC-link capacitor voltage is held constant without using a
separate controller. The STATCOM are designed using SVPWM technique. Through adjustment of the
modulation index, fast modulation of the STATCOM reactive power output can be achieved due to high
sensitivity of the same with respect to the output voltage of the STATCOM VSC. The model, with PI controllers
has been simulated in MATLAB/SIMULINK environment with variation of the pre-charge voltage on the DClink
capacitor with linear loads (inductive). Improvement of the power factor of the grid current is achieved for
linear loads.
Torque Ripple Minimization of a BLDC Motor Drive by Using Electronic Commutat...AI Publications
Brushless DC motors are having a major problem with harmonics in torque. The variations in speed and production of noise should be minimized by using proper topologies. BLDC motors have been gaining attention from different Industrial and domestic appliance manufacturers, because of their high efficiency, high power density and easy maintenance and low cost. This paper presents a three phase BLDC motor with low cost drive to be driven without DC link capacitor. The proposed technique uses an electronic commutation and operates the machine exclusive of the intermediate DC link capacitor. The designing of Brushless DC motor drive system along with control system for torque ripple minimization, speed controller and current controllers are presented using MATLAB / SIMULINK and results are evaluated.
Simulation of Five Level Diode Clamped Multilevel Inverterrahulmonikasharma
The power electronics device which converts DC power to AC power at required output voltage and frequency level is known as inverter. The voltage source inverters produce an output voltage or a current with levels either 0 or +ve or-ve V dc. They are known as two-level inverters. Multilevel inverter is to synthesize a near sinusoidal voltage from several levels of dc voltages. Multilevel inverter has advantage like minimum harmonic distortion. Multi-level inverters are emerging as the new breed of power converter options for high power applications. They typically synthesize the stair-case voltage waveform (from several dc sources) which has reduced harmonic content. Multi-level inverters have many attractive features, high voltage capability, reduced common mode voltages near sinusoidal outputs, low dv/dt, and smaller or even no output filter; sometimes no transformer is required at the input side, called the transformer-less solution, making them suitable for high power applications In this paper a 5-level Diode clamped multilevel inverter is developed by IGBTS using Simulink. Gating signals for these IGBTS have been generated by designing comparators. In order to maintain the different voltage levels at appropriate intervals, the conduction time intervals of IGBT have been maintained by controlling the pulse width of gating pulses[6] (by varying the reference signals magnitude of the comparator). The simulation results for 5-level and THD for the output have been identified by MATLAB/SIMULINK.
Simulation of D-STATCOM to study Voltage Stability in Distribution systemijsrd.com
This paper presents the simulation of D-statcom to understand the improvement of voltage stability [1] of distribution system. The power circuits of the D-STATCOM and distribution networks are made up of simpower system blocks, while the control circuits made with the simulink blocks The STATCOM is applied to regulate transmission voltage to allow greater power flow in a voltage limited transmission network, in the same manner as a static var compensator (SVC), the STATCOM has further potential by giving an inherently faster response and greater output to a system with depressed voltage and offers improved quality of supply. The main applications of the STATCOM are; Distribution STATCOM (D-STATCOM) exhibits high speed control of reactive power to provide voltage stabilization and other type of system control. The DSTATCOM protects the utility transmission or distribution system from voltage sag and /or flicker caused by rapidly varying reactive current demand. During the transient conditions the D-STATCOM provides leading or lagging reactive power to active system stability, power factor correction and load balancing.
For the up-coming generations of power-supply systems, the load located area power-supply sources are an effective one, in terms of our requirements: simplicity, integrity, battery-backup, etc. This could follow the Normalization of power factor & Reducing THD% values on input current, which makes us to add an essential to include a power-factor correction unit at supply side in these new typical topologies. This Proposed architecture presents an integrated battery manage system which can also offers PF correction along with Galvanic-Isolation of battery in a humble single structure. [3] The proposed scheme has the reliable characters like increased efficiency, compact circuit and reduced costs associated with a traditional standalone multiple-stages UPS with PFC. This paper addresses the UPS action, the analysis and simulation results of Proposed UPS scheme.
This paper presents the application of modular multilevel converter (MMC) as a static compensator (STATCOM) for reactive current control. The current control is mostly achieved using proportional controller, proportional-integral (PI) controller, and hysteresis controller among others. PI controllers have the advantage of low harmonics and small variations. However, due to the PI controller’s dependency on the system parameters and also due to the variations within the MMC during capacitors voltage control, variation in the MMC performance during the STATCOM non-ideal operations occur. To mitigate this, an improved performance of MMC will be presented using vector-based compensation concept. The proposed control will be introduced to depress the effect of the dynamics of the MMC based STATCOM non-ideal variations considering the impact of the voltage disturbance. This will be achieved by the introduction of voltage variables to subtract the transient variations from PI controllers’ outputs at the grid-interface; thus, improving the performance.
Brushless DC motor is a synchronous machine that makes use of electronic commutation instead of mechanical commutator. Brushless DC motors makes use of inverter encompassing static switches for its operation. A simple bridge converter when used for BLDC drive as front end converter makes input source power factor to get reduced which is unacceptable in the power system. To avoid the distortions in the source voltage and source currents, Buck converter which was used as power factor correction (PFC) converter in this paper to improve the power factor. Presence of power electronic converters deteriorates system power factor effecting overall system performance. This paper presents buck converter for power factor correction in brushless DC motor drive system. Buck converter is operated with current control strategy rather to conventional voltage follower control. Simulation model was obtained using MATLAB/SIMULINK software and the brushless DC motor performance characteristics were shown for conditions with different DC link voltages and step variation in DC link voltage. Total harmonic distortion in source current was also presented.
This paper presents combinations of level shifted pulse-width modulation algorithm with conventional discontinuous pulse-width modulation methods for cascaded multilevel inverters. In the proposed DPWM a zero sequence signal is injected in sinusoidal reference signal to generate various modulators with easier implementation. The analysis four various control strategies namely Common Carrier (CC), Inverted Carrier (IC), Phase Shifted (PS) and Inverted Phase Shift (IPS) for cascaded multilevel inverter fed induction motor drive has been illustrated. To validate the proposed work experimental tests has been carried out using dSPACE controller. Experimental study proves that using proposed algorithms reduction in common-mode voltage with fewer harmonics along with reduced switching loss for a cascaded multilevel inverter fed motor drive has been achieved.
Distribution Static Synchronous Compensator (DSTATCOM) is a shunt compensating device which is used
to improve current profile by exchanging of reactive power with unbalanced and nonlinear load. DSTATCOM is a
shunt compensating device used for power quality improvement in distribution systems. Relevant solutions are
applied for harmonics, fluctuation of voltage, voltage deviation, unbalance of three phase voltage and current and
frequency deviation. Different controlling schemes such as Phase Control Method (PCM), Fryze Power Theory
(FPT), Synchronous Reference Frame Theory (SRFT) and Instantaneous Reactive Power Theory (IRPT) are used
for reactive power compensation with the help of Voltage source Inverter (VSI). In this project we are going to
balance the source current using different control schemes. The results of different source currents are compared
with a different control schemes in terms of active and reactive power and in terms of Total Harmonic Distortion
(THD) for nonlinear load using Fryze Power Theory (FPT) and Instantaneous Reactive Power Theory (IRPT).
Reference currents are generated by the different control schemes have been dynamically traced in a hysteresis
current controller. The performance of DSTATCOM for different control schemes is validated for load balancing
and harmonic elimination by using simulation models in MATLAB/SIMULINK
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
International Journal of Engineering Research and Applications (IJERA) is a team of researchers not publication services or private publications running the journals for monetary benefits, we are association of scientists and academia who focus only on supporting authors who want to publish their work. The articles published in our journal can be accessed online, all the articles will be archived for real time access.
Our journal system primarily aims to bring out the research talent and the works done by sciaentists, academia, engineers, practitioners, scholars, post graduate students of engineering and science. This journal aims to cover the scientific research in a broader sense and not publishing a niche area of research facilitating researchers from various verticals to publish their papers. It is also aimed to provide a platform for the researchers to publish in a shorter of time, enabling them to continue further All articles published are freely available to scientific researchers in the Government agencies,educators and the general public. We are taking serious efforts to promote our journal across the globe in various ways, we are sure that our journal will act as a scientific platform for all researchers to publish their works online.
STATCOM can provide fast and efficient reactive power support to maintain power system voltage stability. In the literature, various STATCOM control methods have been discussed including many applications of proportional-integral (PI) controllers. However, these previous works obtain the PI gains via a trial-and-error approach or extensive studies with a tradeoff of performance and applicability. Hence, control parameters for the optimal performance at a given operating point may not be effective at a different operating point. This paper proposes a new control model based on adaptive PI control, which can self-adjust the control gains during a disturbance such that the performance always matches a desired response, regardless of the change of operating condition. Since the adjustment is autonomous, this gives the plug-and-play capability for STATCOM operation. In the simulation test, the adaptive PI control shows consistent excellence under various operating conditions, such as different initial control gains, different load levels, change of transmission network, consecutive disturbances, and a severe disturbance. In contrast, the conventional STATCOM control with tuned, fixed PI gains usually perform fine in the original system, but may not perform as efficient as the proposed control method when there is a change of system conditions.
Ieee 2014 2015 matlab power system projects titles list globalsoft technologiesIEEEJAVAPROJECTS
To Get any Project for CSE, IT ECE, EEE Contact Me @ 09666155510, 09849539085 or mail us - ieeefinalsemprojects@gmail.com-Visit Our Website: www.globalsofttechnologies.org
For the up-coming generations of power-supply systems, the load located area power-supply sources are an effective one, in terms of our requirements: simplicity, integrity, battery-backup, etc. This could follow the Normalization of power factor & Reducing THD% values on input current, which makes us to add an essential to include a power-factor correction unit at supply side in these new typical topologies. This Proposed architecture presents an integrated battery manage system which can also offers PF correction along with Galvanic-Isolation of battery in a humble single structure. [3] The proposed scheme has the reliable characters like increased efficiency, compact circuit and reduced costs associated with a traditional standalone multiple-stages UPS with PFC. This paper addresses the UPS action, the analysis and simulation results of Proposed UPS scheme.
This paper presents the application of modular multilevel converter (MMC) as a static compensator (STATCOM) for reactive current control. The current control is mostly achieved using proportional controller, proportional-integral (PI) controller, and hysteresis controller among others. PI controllers have the advantage of low harmonics and small variations. However, due to the PI controller’s dependency on the system parameters and also due to the variations within the MMC during capacitors voltage control, variation in the MMC performance during the STATCOM non-ideal operations occur. To mitigate this, an improved performance of MMC will be presented using vector-based compensation concept. The proposed control will be introduced to depress the effect of the dynamics of the MMC based STATCOM non-ideal variations considering the impact of the voltage disturbance. This will be achieved by the introduction of voltage variables to subtract the transient variations from PI controllers’ outputs at the grid-interface; thus, improving the performance.
Brushless DC motor is a synchronous machine that makes use of electronic commutation instead of mechanical commutator. Brushless DC motors makes use of inverter encompassing static switches for its operation. A simple bridge converter when used for BLDC drive as front end converter makes input source power factor to get reduced which is unacceptable in the power system. To avoid the distortions in the source voltage and source currents, Buck converter which was used as power factor correction (PFC) converter in this paper to improve the power factor. Presence of power electronic converters deteriorates system power factor effecting overall system performance. This paper presents buck converter for power factor correction in brushless DC motor drive system. Buck converter is operated with current control strategy rather to conventional voltage follower control. Simulation model was obtained using MATLAB/SIMULINK software and the brushless DC motor performance characteristics were shown for conditions with different DC link voltages and step variation in DC link voltage. Total harmonic distortion in source current was also presented.
This paper presents combinations of level shifted pulse-width modulation algorithm with conventional discontinuous pulse-width modulation methods for cascaded multilevel inverters. In the proposed DPWM a zero sequence signal is injected in sinusoidal reference signal to generate various modulators with easier implementation. The analysis four various control strategies namely Common Carrier (CC), Inverted Carrier (IC), Phase Shifted (PS) and Inverted Phase Shift (IPS) for cascaded multilevel inverter fed induction motor drive has been illustrated. To validate the proposed work experimental tests has been carried out using dSPACE controller. Experimental study proves that using proposed algorithms reduction in common-mode voltage with fewer harmonics along with reduced switching loss for a cascaded multilevel inverter fed motor drive has been achieved.
Distribution Static Synchronous Compensator (DSTATCOM) is a shunt compensating device which is used
to improve current profile by exchanging of reactive power with unbalanced and nonlinear load. DSTATCOM is a
shunt compensating device used for power quality improvement in distribution systems. Relevant solutions are
applied for harmonics, fluctuation of voltage, voltage deviation, unbalance of three phase voltage and current and
frequency deviation. Different controlling schemes such as Phase Control Method (PCM), Fryze Power Theory
(FPT), Synchronous Reference Frame Theory (SRFT) and Instantaneous Reactive Power Theory (IRPT) are used
for reactive power compensation with the help of Voltage source Inverter (VSI). In this project we are going to
balance the source current using different control schemes. The results of different source currents are compared
with a different control schemes in terms of active and reactive power and in terms of Total Harmonic Distortion
(THD) for nonlinear load using Fryze Power Theory (FPT) and Instantaneous Reactive Power Theory (IRPT).
Reference currents are generated by the different control schemes have been dynamically traced in a hysteresis
current controller. The performance of DSTATCOM for different control schemes is validated for load balancing
and harmonic elimination by using simulation models in MATLAB/SIMULINK
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
International Journal of Engineering Research and Applications (IJERA) is a team of researchers not publication services or private publications running the journals for monetary benefits, we are association of scientists and academia who focus only on supporting authors who want to publish their work. The articles published in our journal can be accessed online, all the articles will be archived for real time access.
Our journal system primarily aims to bring out the research talent and the works done by sciaentists, academia, engineers, practitioners, scholars, post graduate students of engineering and science. This journal aims to cover the scientific research in a broader sense and not publishing a niche area of research facilitating researchers from various verticals to publish their papers. It is also aimed to provide a platform for the researchers to publish in a shorter of time, enabling them to continue further All articles published are freely available to scientific researchers in the Government agencies,educators and the general public. We are taking serious efforts to promote our journal across the globe in various ways, we are sure that our journal will act as a scientific platform for all researchers to publish their works online.
STATCOM can provide fast and efficient reactive power support to maintain power system voltage stability. In the literature, various STATCOM control methods have been discussed including many applications of proportional-integral (PI) controllers. However, these previous works obtain the PI gains via a trial-and-error approach or extensive studies with a tradeoff of performance and applicability. Hence, control parameters for the optimal performance at a given operating point may not be effective at a different operating point. This paper proposes a new control model based on adaptive PI control, which can self-adjust the control gains during a disturbance such that the performance always matches a desired response, regardless of the change of operating condition. Since the adjustment is autonomous, this gives the plug-and-play capability for STATCOM operation. In the simulation test, the adaptive PI control shows consistent excellence under various operating conditions, such as different initial control gains, different load levels, change of transmission network, consecutive disturbances, and a severe disturbance. In contrast, the conventional STATCOM control with tuned, fixed PI gains usually perform fine in the original system, but may not perform as efficient as the proposed control method when there is a change of system conditions.
Ieee 2014 2015 matlab power system projects titles list globalsoft technologiesIEEEJAVAPROJECTS
To Get any Project for CSE, IT ECE, EEE Contact Me @ 09666155510, 09849539085 or mail us - ieeefinalsemprojects@gmail.com-Visit Our Website: www.globalsofttechnologies.org
Design & Implementation of Controller Based Buck-Boost Converter for Small Wi...iosrjce
This paper propose to design a controller based buck boost converter for the effective utilization of
the wind machine. By implementing a controller based Buck-Boost converter, the voltage produced at the lower
wind speeds can also be utilized effectively by boosting it to the rated charging voltage of the battery. Also if the
wind speed is high, the DC output voltage will increase then the converter bucks this high voltage to the
nominal battery charging voltage (48V), thereby protecting the battery from over charging voltage. Thus the
effective utilization of the wind machine has been achieved by the use of the proposed controller based buck
boost converter.
Investigation of Integrated Rectangular SIW Filter and Rectangular Microstrip...IJASCSE
This paper presents an investigation based on the resonant circuit approach to characterize an integrated microwave filter and antenna from a lumped element prototype. This approach is used to design an integrated filter and antenna to reduce the overall size of the physical dimensions of the RF/microwave front-end subsystem. This study focuses on the integration of a rectangular Substrate Integrated Waveguide (SIW) filter with a rectangular microstrip patch antenna to produce a filtering and radiating element in a single device. The physical layouts of the SIW filter and rectangular microstrip patch antenna based on single- and dual-mode will be developed. To prove the concept, the integrated microwave filter and antenna at a center frequency of 2 GHz is demonstrated and validated through simulation and laboratory experiments. The experimental performance yielded promising results that were in good agreement with the simulated results. This study is beneficial for microwave systems, given that the reduction of the complexity of design and physical dimension as well as cost are important for applications such as base stations and multiplexers in wireless communication systems.
Low-power Innovative techniques for Wearable ComputingOmar Elshal
A presentation i did for the Ubiquitous and Wearable Computing seminar during my senior year in university.
The presentation introduces many research papers on the field then discusses one of them thoroughly.
Centralised hybrid renewable power generation using diso buck boost converter...Naresh K
The DISO-Dual Input Single Output converter combines the two energy sources. The converter is designed considering double input, in which same or different type of two inputs can be used individually or simultaneously.
Pantech provide supports on antenna design projects for final year students.. We guide you to implement both on simulation and hardware design.www.pantech proed.com
Swing, voltage stability and power transfer capability in transmission system...eSAT Journals
Abstract In modern era, the increasing size of the power system, to maximize the use of existing systems and to provide adequate voltage support is an emphasis on finding solutions. This flexibility is needed electricity. Better placed than the Flexible AC Transmission Systems (FACTS) to control the flow of electricity, and to provide voltage support can be effective in turn resulting in less damage. The impact of these tools on line flow and bus voltage profile at random algorithm to determine the optimal number of ratings have been studied by keeping them better . The FACTS devices are expensive cause of that FACTS type, number and location of the FACTS devices is very important, for decide the optimal location and parameters of FACTS devices. FACTS are used in the following purposes: Transmission pricing issues by maximizing social welfare with or without consideration of FACTS’ costs; Better utilization of FACT by maximizing FACTS devices total transferred power; Reactive power or voltage control by minimizing transmission losses, or voltage fluctuation. Increase system’s security under emergency by minimizing transmission lines loadability. Power flow control, a current long transmission line, plays an important role within the energy system. The letter swings, long-distance transmission line voltage and power flow control in unified power flow controller (UPFC) based compensation associated series or shunt FACTS devices are employed. Devices such as the proposed transmission line, between the end of the sending and receiving end to the transmission line is used in places as different. Here also deals with determining the optimum placement of Flexible AC Transmission Systems (FACTS) damping out swings, voltage and improves power transfer devices for a long transmission line. Here the concept of compensation mid-point of facts is presented for optimal placement. Keywords: Stability, first swings, rotor angle, power transfer, Flexible AC Transmission Systems (FACTS), Unified Power Flow Controller (UPFC), reactive power
Lclr filter design and modelling for harmonic mitigation in interconnected mi...eSAT Journals
Abstract Today many people are attracted towards distribution generation (DG) because of low energy cost power supply, local generation, highly reliable system, supply with good power quality. Increasing attention and investment in renewable energy that is DG energy sources give rise to rapid development of high penetration renewable energy sources like solar energy, wind energy, hydro energy. Out of this most important and best is the solar energy. There are multiple ways to interface PV arrays with the power grid, but in there is problem of power quality. Today’s important concern of the power system is the power quality in case of renewable energy sources. The power quality improvement in the interconnected micro grid systems and grid interconnection with Distribution Generation (DGs) is the challenging task and to overcome the power quality problem passive filters are the best and cost effective solution. In this paper the LCLR filter is implemented between inverter and grid. The complete system consists of photovoltaic cell (PV), DC-DC boost converter, DC-AC inverter, LCLR filter and the grid. This paper also consists of complete MATLAB simulation of PV cell, DC-DC boost converter and inverter with LCLR filter. Key Words: Renewable energy, PV module, DC-DC boost converter, DGs, LCLR filter, power quality, micro grid (MG) and THD
A Voltage Controlled Dstatcom for Power Quality Improvementiosrjce
Due to increasing complexity in the power system, voltage sag is becoming one of the most significant
power quality problems. Voltage sag is a short reduction voltage from nominal voltage, occurs in a short time.
If the voltage sags exceed two to three cycles, then manufacturing systems making use of sensitive electronic
equipments are likely to be affected leading to major problems. It ultimately leads to wastage of resources (both
material and human) as well as financial losses. This is possible only by ensuring that uninterrupted flow of
power is maintained at proper voltage levels. This project tends look at the solving the sag problems by using
custom power devices such as Distribution Static compensator (D-STATCOM).Proposed scheme follows a new
algorithm to generate reference voltage for a distribution static compensator (DSTATCOM) operating in
voltage-control mode. The proposed scheme ensures that unity power factor (UPF) is achieved at the load
terminal during nominal operation, which is not possible in the traditional method. Also, the compensator
injects lower currents therefore, reduces losses in the feeder and voltage-source inverter. Further, a saving in
the rating of DSTATCOM is achieved which increases its capacity to mitigate voltage sag. Nearly UPF is
maintained, while regulating voltage at the load terminal, during load change. The state-space model of
DSTATCOM is incorporated with the deadbeat predictive controller for fast load voltage regulation during
voltage disturbances. With these features, this scheme allows DSTATCOM to tackle power-quality issues by
providing power factor correction, harmonic elimination, load balancing, and voltage regulation based on the
load requirement.
Droop control method for parallel dc converters used in standalone pv wind po...eSAT Journals
Abstract The rising rate of consumption and price of fossil fuel along with environmental pollution by conventional power generation draw global attention to renewable energy sources and technology. Paper gives analysis study on current sharing issues of parallel DC converters in standalone photovoltaic (PV) WIND system. Solar wind power generating system with maximum power point tracking (MPPT) technique – incremental conductance method is used for the simulation analysis. The main drawbacks of parallel converters used in system are poor power sharing and voltage drop. The paper describes about instantaneous droop calculation considering effect of cable resistance using droop index to improve the power sharing performance. The control technique is simulated using MATLAB/SIMULINK in PV- wind power generating system with MPPT and case study has been done on the control strategy and verifies the effectiveness of adaptive droop control on output converter voltage. Key Words: Microgrid; droop method; incremental conductance (Incond); maximum power point tracking (MPPT).
Mitigation of Voltage Sag/Swell with Fuzzy Control Reduced Rating DVRIJERD Editor
Power quality has been an issue that is becoming increasingly pivotal in industrial electricity
consumers point of view in recent times. Modern industries employ Sensitive power electronic equipments,
control devices and non-linear loads as part of automated processes to increase energy efficiency and
productivity. Voltage disturbances are the most common power quality problem due to this the use of a large
numbers of sophisticated and sensitive electronic equipment in industrial systems is increased. This paper
discusses the design and simulation of dynamic voltage restorer for improvement of power quality and
reduce the harmonics distortion of sensitive loads. Power quality problem is occurring at non-standard
voltage, current and frequency. Electronic devices are very sensitive loads. In power system voltage sag,
swell, flicker and harmonics are some of the problem to the sensitive load. The compensation capability
of a DVR depends primarily on the maximum voltage injection ability and the amount of stored
energy available within the restorer. This device is connected in series with the distribution feeder at
medium voltage. A fuzzy logic control is used to produce the gate pulses for control circuit of DVR and the
circuit is simulated by using MATLAB/SIMULINK software.
FOUR QUADRANT SPEED CONTROL OF DC MOTOR USING AT89S52 MICROCONTROLLERJournal For Research
Speed control of a machine is the most vital and important part in any industrial organization. This paper is designed to develop a four quadrant speed control system for a DC motor using microcontroller. The motor is operated in four quadrants i.e. clockwise, counter clock-wise, forward brake and reverse brake. It also has a feature of speed control. The four quadrant operation of the dc motor is best suited for industries where motors are used and as per requirement they can rotate in clockwise, counter-clockwise and also apply brakes immediately in both the directions. In case of a specific operation in industrial environment, the motor needs to be stopped immediately. In such scenario, this proposed system is very apt as forward brake and reverse brake are its integral features. Instantaneous brake in both the directions happens as a result of applying a reverse voltage across the running motor for a brief period and the speed control of the motor can be achieved with the PWM pulses generated by the microcontroller. The microcontroller used in this project is from 8051 family. Push buttons are provided for the operation of the motor which are interfaced to the microcontroller that provides an input signal to it and controls the speed of the motor through a motor driver IC. The speed and direction of DC motor has been observed on digital CRO. Microcontroller programming has been written in assembly language by using notepad and it has been converted in hex file by using micro vision Kiel. The burning of programming in the 8051 microcontroller chip has been done by using positron boot loader software.
Shunt Compensation for Power Quality Improvement using a STATCOM ControllerIDES Editor
This paper addresses the issue of the modeling
and analysis of STATCOM controller. The transient
analysis and modeling is performed with the state-of-theart
digital simulator PSCAD 4.2.1. Simulation were
carried out for both cases where, STATCOM was
connected into the system and not, with simulation
interval 3-5 sec. The aim of the STATCOM is to provide
good power quality at the point of common coupling
(PCC). Some simulation results are presented, which
shows the compensation effectiveness of the STATCOM
controller at the connected bus.
IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Enhancement of Power System Dynamics Using a Novel Series Compensation SchemeIJMER
Phase imbalanced capacitive compensation is a “hybrid” series compensation scheme, where the
series capacitive compensation in one phase is created using a single-phase TCSC in series with a fixed capacitor
(Cc), and the other two phases are compensated by fixed series capacitors (C). The TCSC control is initially set
such that its equivalent compensations at the power frequency combined with the fixed capacitor yield a
resultant compensation equal to the other two phases. Thus, the phase balance is maintained at the power
frequency while at any other frequency, a phase imbalance is created. The effectiveness of the scheme in damping
power system oscillations for various network conditions, namely different system faults and tie-line power flows is
evaluated using the MATLAB/SIMULINK Software
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
POWER QUALITY IMPROVEMENT BY SSSC AND STATCOM USING PI CONTROLLERJournal For Research
This paper presents the enhancement of voltage stability using Static Synchronous compensator (STATCOM) and Static Synchronous series compensator (SSSC). In recent past years, along with the rapid increasing electrical power requirement has caused system to be heavily loaded leading to voltage instability. Under this condition there may be insufficient reactive power causing voltage to drop at various buses. The result would be the occurrence of voltage collapse which leads to total blackout of the whole system. FACT controllers have been used for solving various stability control problems. In this paper, SSSC and STATCOM are used to investigate the effect of these devices in controlling active and reactive powers to maintain voltage stability. The PI Controller is used to tune the circuit and to provide the zero signal error. Simulation results have been presented in MATLAB/Simulink environment for two machines four buses system.
International Journal of Engineering Research and Development (IJERD)IJERD Editor
We would send hard copy of Journal by speed post to the address of correspondence author after online publication of paper.
We will dispatched hard copy to the author within 7 days of date of publication
Voltage Sag Mitigation in Utility Connected System Using Current Source Conve...IDES Editor
This paper discusses the implementation of current
source converter based distribution type static synchronous
compensator. For eliminating the lower order harmonics, the
power semiconductors are switched by pulse width modulation
technique. Current source converter, input filter, dc link
reactor are combined to design the proposed CSC based
STATCOM. Since the STATCOM is a current injection
device, the performance of the device is improved by a currentsource
converter (CSC) combination. So a controllable current
is generated at the output terminals of the device. Filter circuit
at the input terminal is designed to eliminate the higher order
harmonics. The proposed D- STATCOM is simulated and the
results are validated using MATLAB.
International Journal of Engineering Research and Development is an international premier peer reviewed open access engineering and technology journal promoting the discovery, innovation, advancement and dissemination of basic and transitional knowledge in engineering, technology and related disciplines.
We follow "Rigorous Publication" model - means that all articles appear on IJERD after full appraisal, effectiveness, legitimacy and reliability of research content. International Journal of Engineering Research and Development publishes papers online as well as provide hard copy of Journal to authors after publication of paper. It is intended to serve as a forum for researchers, practitioners and developers to exchange ideas and results for the advancement of Engineering & Technology.
International Journal of Engineering Research and Development is an international premier peer reviewed open access engineering and technology journal promoting the discovery, innovation, advancement and dissemination of basic and transitional knowledge in engineering, technology and related disciplines.
We follow "Rigorous Publication" model - means that all articles appear on IJERD after full appraisal, effectiveness, legitimacy and reliability of research content. International Journal of Engineering Research and Development publishes papers online as well as provide hard copy of Journal to authors after publication of paper. It is intended to serve as a forum for researchers, practitioners and developers to exchange ideas and results for the advancement of Engineering & Technology.
Power System State Estimation - A ReviewIDES Editor
The aim of this article is to provide a comprehensive
survey on power system state estimation techniques. The
algorithms used for finding the system states under both static
and dynamic state estimations are discussed in brief. The
authors are opinion that the scope of pursuing research in the
area of state estimation with PMU and SCADA measurements
is the state of the art and timely.
Artificial Intelligence Technique based Reactive Power Planning Incorporating...IDES Editor
Reactive Power Planning is a major concern in the
operation and control of power systems This paper compares
the effectiveness of Evolutionary Programming (EP) and
New Improved Differential Evolution (NIMDE) to solve
Reactive Power Planning (RPP) problem incorporating
FACTS Controllers like Static VAR Compensator (SVC),
Thyristor Controlled Series Capacitor (TCSC) and Unified
power flow controller (UPFC) considering voltage stability.
With help of Fast Voltage Stability Index (FVSI), the critical
lines and buses are identified to install the FACTS controllers.
The optimal settings of the control variables of the generator
voltages,transformer tap settings and allocation and parameter
settings of the SVC,TCSC,UPFC are considered for reactive
power planning. The test and Validation of the proposed
algorithm are conducted on IEEE 30–bus system and 72-bus
Indian system.Simulation results shows that the UPFC gives
better results than SVC and TCSC and the FACTS controllers
reduce the system losses.
Design and Performance Analysis of Genetic based PID-PSS with SVC in a Multi-...IDES Editor
Damping of power system oscillations with the help
of proposed optimal Proportional Integral Derivative Power
System Stabilizer (PID-PSS) and Static Var Compensator
(SVC)-based controllers are thoroughly investigated in this
paper. This study presents robust tuning of PID-PSS and
SVC-based controllers using Genetic Algorithms (GA) in
multi machine power systems by considering detailed model
of the generators (model 1.1). The effectiveness of FACTSbased
controllers in general and SVC-based controller in
particular depends upon their proper location. Modal
controllability and observability are used to locate SVC–based
controller. The performance of the proposed controllers is
compared with conventional lead-lag power system stabilizer
(CPSS) and demonstrated on 10 machines, 39 bus New England
test system. Simulation studies show that the proposed genetic
based PID-PSS with SVC based controller provides better
performance.
Optimal Placement of DG for Loss Reduction and Voltage Sag Mitigation in Radi...IDES Editor
This paper presents the need to operate the power
system economically and with optimum levels of voltages has
further led to an increase in interest in Distributed
Generation. In order to reduce the power losses and to improve
the voltage in the distribution system, distributed generators
(DGs) are connected to load bus. To reduce the total power
losses in the system, the most important process is to identify
the proper location for fixing and sizing of DGs. It presents a
new methodology using a new population based meta heuristic
approach namely Artificial Bee Colony algorithm(ABC) for
the placement of Distributed Generators(DG) in the radial
distribution systems to reduce the real power losses and to
improve the voltage profile, voltage sag mitigation. The power
loss reduction is important factor for utility companies because
it is directly proportional to the company benefits in a
competitive electricity market, while reaching the better power
quality standards is too important as it has vital effect on
customer orientation. In this paper an ABC algorithm is
developed to gain these goals all together. In order to evaluate
sag mitigation capability of the proposed algorithm, voltage
in voltage sensitive buses is investigated. An existing 20KV
network has been chosen as test network and results are
compared with the proposed method in the radial distribution
system.
Line Losses in the 14-Bus Power System Network using UPFCIDES Editor
Controlling power flow in modern power systems
can be made more flexible by the use of recent developments
in power electronic and computing control technology. The
Unified Power Flow Controller (UPFC) is a Flexible AC
transmission system (FACTS) device that can control all the
three system variables namely line reactance, magnitude and
phase angle difference of voltage across the line. The UPFC
provides a promising means to control power flow in modern
power systems. Essentially the performance depends on proper
control setting achievable through a power flow analysis
program. This paper presents a reliable method to meet the
requirements by developing a Newton-Raphson based load
flow calculation through which control settings of UPFC can
be determined for the pre-specified power flow between the
lines. The proposed method keeps Newton-Raphson Load Flow
(NRLF) algorithm intact and needs (little modification in the
Jacobian matrix). A MATLAB program has been developed to
calculate the control settings of UPFC and the power flow
between the lines after the load flow is converged. Case studies
have been performed on IEEE 5-bus system and 14-bus system
to show that the proposed method is effective. These studies
indicate that the method maintains the basic NRLF properties
such as fast computational speed, high degree of accuracy and
good convergence rate.
Study of Structural Behaviour of Gravity Dam with Various Features of Gallery...IDES Editor
The size and shape of opening in dam causes the
stress concentration, it also causes the stress variation in the
rest of the dam cross section. The gravity method of the analysis
does not consider the size of opening and the elastic property
of dam material. Thus the objective of study is comprises of
the Finite Element Method which considers the size of
opening, elastic property of material, and stress distribution
because of geometric discontinuity in cross section of dam.
Stress concentration inside the dam increases with the opening
in dam which results in the failure of dam. Hence it is
necessary to analyses large opening inside the dam. By making
the percentage area of opening constant and varying size and
shape of opening the analysis is carried out. For this purpose
a section of Koyna Dam is considered. Dam is defined as a
plane strain element in FEM, based on geometry and loading
condition. Thus this available information specified our path
of approach to carry out 2D plane strain analysis. The results
obtained are then compared mutually to get most efficient
way of providing large opening in the gravity dam.
Assessing Uncertainty of Pushover Analysis to Geometric ModelingIDES Editor
Pushover Analysis a popular tool for seismic
performance evaluation of existing and new structures and is
nonlinear Static procedure where in monotonically increasing
loads are applied to the structure till the structure is unable
to resist the further load .During the analysis, whatever the
strength of concrete and steel is adopted for analysis of
structure may not be the same when real structure is
constructed and the pushover analysis results are very sensitive
to material model adopted, geometric model adopted, location
of plastic hinges and in general to procedure followed by the
analyzer. In this paper attempt has been made to assess
uncertainty in pushover analysis results by considering user
defined hinges and frame modeled as bare frame and frame
with slab modeled as rigid diaphragm and results compared
with experimental observations. Uncertain parameters
considered includes the strength of concrete, strength of steel
and cover to the reinforcement which are randomly generated
and incorporated into the analysis. The results are then
compared with experimental observations.
Secure Multi-Party Negotiation: An Analysis for Electronic Payments in Mobile...IDES Editor
This paper is an attempt to base on auctions which
presents a frame work for the secure multi-party decision
protocols. In addition to the implementations which are very
light weighted, the main focus is on synchronizing security
features for avoiding agreements manipulations and reducing
the user traffic. Through this paper one can understand that
this different auction protocols on top of the frame work can
be collaborated using mobile devices. This paper present the
negotiation between auctioneer and the proffered and this
negotiation shows that multiparty security is far better than
the existing system.
Selfish Node Isolation & Incentivation using Progressive ThresholdsIDES Editor
The problems associated with selfish nodes in
MANET are addressed by a collaborative watchdog approach
which reduces the detection time for selfish nodes thereby
improves the performance and accuracy of watchdogs[1]. In
the related works they make use of credit based systems, reputation
based mechanisms, pathrater and watchdog mechanism
to detect such selfish nodes. In this paper we follow an approach
of collaborative watchdog which reduces the detection
time for selfish nodes and also involves the removal of such
selfish nodes based on some progressively assessed thresholds.
The threshold gives the nodes a chance to stop misbehaving
before it is permanently deleted from the network.
The node passes through several isolation processes before it
is permanently removed. Another version of AODV protocol
is used here which allows the simulation of selfish nodes in
NS2 by adding or modifying log files in the protocol.
Various OSI Layer Attacks and Countermeasure to Enhance the Performance of WS...IDES Editor
Wireless sensor networks are networks having non
wired infrastructure and dynamic topology. In OSI model each
layer is prone to various attacks, which halts the performance
of a network .In this paper several attacks on four layers of
OSI model are discussed and security mechanism is described
to prevent attack in network layer i.e wormhole attack. In
Wormhole attack two or more malicious nodes makes a covert
channel which attracts the traffic towards itself by depicting a
low latency link and then start dropping and replaying packets
in the multi-path route. This paper proposes promiscuous mode
method to detect and isolate the malicious node during
wormhole attack by using Ad-hoc on demand distance vector
routing protocol (AODV) with omnidirectional antenna. The
methodology implemented notifies that the nodes which are
not participating in multi-path routing generates an alarm
message during delay and then detects and isolate the
malicious node from network. We also notice that not only
the same kind of attacks but also the same kind of
countermeasures can appear in multiple layer. For example,
misbehavior detection techniques can be applied to almost all
the layers we discussed.
Responsive Parameter based an AntiWorm Approach to Prevent Wormhole Attack in...IDES Editor
The recent advancements in the wireless technology
and their wide-spread deployment have made remarkable
enhancements in efficiency in the corporate and industrial
and Military sectors The increasing popularity and usage of
wireless technology is creating a need for more secure wireless
Ad hoc networks. This paper aims researched and developed
a new protocol that prevents wormhole attacks on a ad hoc
network. A few existing protocols detect wormhole attacks but
they require highly specialized equipment not found on most
wireless devices. This paper aims to develop a defense against
wormhole attacks as an Anti-worm protocol which is based on
responsive parameters, that does not require as a significant
amount of specialized equipment, trick clock synchronization,
no GPS dependencies.
Cloud Security and Data Integrity with Client Accountability FrameworkIDES Editor
The Cloud based services provide much efficient
and seamless ways for data sharing across the cloud. The fact
that the data owners no longer possess data makes it very
difficult to assure data confidentiality and to enable secure
data sharing in the cloud. Despite of all its advantages this
will remain a major limitation that acts as a barrier to the
wider deployment of cloud based services. One of the possible
ways for ensuring trust in this aspect is the introduction of
accountability feature in the cloud computing scenario. The
Cloud framework requires promotion of distributed
accountability for such dynamic environment[1]. In some
works, there‘s an accountable framework suggested to ensure
distributed accountability for data sharing by the generation
of only a log of data access, but without any embedded feedback
mechanism for owner permission towards data
protection[2].The proposed system is an enhanced client
accountability framework which provides an additional client
side verification for each access towards enhanced security of
data. The integrity of content of data which resides in the
cloud service provider is also maintained by secured
outsourcing. Besides, the authentication of JAR(Java Archive)
files are done to ensure file protection and to maintain a safer
environment for data sharing. The analysis of various
functionalities of the framework depicts both the
accountability and security feature in an efficient manner.
Genetic Algorithm based Layered Detection and Defense of HTTP BotnetIDES Editor
A System state in HTTP botnet uses HTTP protocol
for the creation of chain of Botnets thereby compromising
other systems. By using HTTP protocol and port number 80,
attacks can not only be hidden but also pass through the
firewall without being detected. The DPR based detection
leads to better analysis of botnet attacks [3]. However, it
provides only probabilistic detection of the attacker and also
time consuming and error prone. This paper proposes a Genetic
algorithm based layered approach for detecting as well as
preventing botnet attacks. The paper reviews p2p firewall
implementation which forms the basis of filtering.
Performance evaluation is done based on precision, F-value
and probability. Layered approach reduces the computation
and overall time requirement [7]. Genetic algorithm promises
a low false positive rate.
Enhancing Data Storage Security in Cloud Computing Through SteganographyIDES Editor
in cloud computing data storage is a significant issue
because the entire data reside over a set of interconnected
resource pools that enables the data to be accessed through
virtual machines. It moves the application software’s and
databases to the large data centers where the management of
data is actually done. As the resource pools are situated over
various corners of the world, the management of data and
services may not be fully trustworthy. So, there are various
issues that need to be addressed with respect to the
management of data, service of data, privacy of data, security
of data etc. But the privacy and security of data is highly
challenging. To ensure privacy and security of data-at-rest in
cloud computing, we have proposed an effective and a novel
approach to ensure data security in cloud computing by means
of hiding data within images following is the concept of
steganography. The main objective of this paper is to prevent
data access from cloud data storage centers by unauthorized
users. This scheme perfectly stores data at cloud data storage
centers and retrieves data from it when it is needed.
The main tasks of a Wireless Sensor Network
(WSN) are data collection from its nodes and communication
of this data to the base station (BS). The protocols used for
communication among the WSN nodes and between the WSN
and the BS, must consider the resource constraints of nodes,
battery energy, computational capabilities and memory. The
WSN applications involve unattended operation of the network
over an extended period of time. In order to extend the lifetime
of a WSN, efficient routing protocols need to be adopted. The
proposed low power routing protocol based on tree-based
network structure reliably forwards the measured data towards
the BS using TDMA. An energy consumption analysis of the
WSN making use of this protocol is also carried out. It is
found that the network is energy efficient with an average
duty cycle of 0:7% for the WSN nodes. The OmNET++
simulation platform along with MiXiM framework is made
use of.
Permutation of Pixels within the Shares of Visual Cryptography using KBRP for...IDES Editor
The security of authentication of internet based
co-banking services should not be susceptible to high risks.
The passwords are highly vulnerable to virus attacks due to
the lack of high end embedding of security methods. In order
for the passwords to be more secure, people are generally
compelled to select jumbled up character based passwords
which are not only less memorable but are also equally prone
to insecurity. Multiple use of distributed shares has been
studied to solve the problem of authentication by algorithms
based on thresholding of pixels in image processing and visual
cryptography concepts where the subset of shares is considered
for the recovery of the original image for authentication using
correlation function[1][2].The main disadvantage in the above
study is the plain storage of shares and also one of the shares
is being supplied to the customer, which will lead to the
possibility of misuse by a third party. This paper proposes a
technique for scrambling of pixels by key based random
permutation (KBRP) within the shares before the
authentication has been attempted. Total number of shares to
be created is dependent on the multiplicity of ownership of
the account. By this method the problem of uncertainty among
the customers with regard to security, storage, retrieval of
holding of half of the shares is minimized.
This paper presents a trifocal Rotman Lens Design
approach. The effects of focal ratio and element spacing on
the performance of Rotman Lens are described. A three beam
prototype feeding 4 element antenna array working in L-band
has been simulated using RLD v1.7 software. Simulated
results show that the simulated lens has a return loss of –
12.4dB at 1.8GHz. Beam to array port phase error variation
with change in the focal ratio and element spacing has also
been investigated.
Band Clustering for the Lossless Compression of AVIRIS Hyperspectral ImagesIDES Editor
Hyperspectral images can be efficiently compressed
through a linear predictive model, as for example the one
used in the SLSQ algorithm. In this paper we exploit this
predictive model on the AVIRIS images by individuating,
through an off-line approach, a common subset of bands, which
are not spectrally related with any other bands. These bands
are not useful as prediction reference for the SLSQ 3-D
predictive model and we need to encode them via other
prediction strategies which consider only spatial correlation.
We have obtained this subset by clustering the AVIRIS bands
via the clustering by compression approach. The main result
of this paper is the list of the bands, not related with the
others, for AVIRIS images. The clustering trees obtained for
AVIRIS and the relationship among bands they depict is also
an interesting starting point for future research.
Microelectronic Circuit Analogous to Hydrogen Bonding Network in Active Site ...IDES Editor
A microelectronic circuit of block-elements
functionally analogous to two hydrogen bonding networks is
investigated. The hydrogen bonding networks are extracted
from â-lactamase protein and are formed in its active site.
Each hydrogen bond of the network is described in equivalent
electrical circuit by three or four-terminal block-element.
Each block-element is coded in Matlab. Static and dynamic
analyses are performed. The resultant microelectronic circuit
analogous to the hydrogen bonding network operates as
current mirror, sine pulse source, triangular pulse source as
well as signal modulator.
Texture Unit based Monocular Real-world Scene Classification using SOM and KN...IDES Editor
In this paper a method is proposed to discriminate
real world scenes in to natural and manmade scenes of similar
depth. Global-roughness of a scene image varies as a function
of image-depth. Increase in image depth leads to increase in
roughness in manmade scenes; on the contrary natural scenes
exhibit smooth behavior at higher image depth. This particular
arrangement of pixels in scene structure can be well explained
by local texture information in a pixel and its neighborhood.
Our proposed method analyses local texture information of a
scene image using texture unit matrix. For final classification
we have used both supervised and unsupervised learning using
K-Nearest Neighbor classifier (KNN) and Self Organizing
Map (SOM) respectively. This technique is useful for online
classification due to very less computational complexity.
Dev Dives: Train smarter, not harder – active learning and UiPath LLMs for do...UiPathCommunity
💥 Speed, accuracy, and scaling – discover the superpowers of GenAI in action with UiPath Document Understanding and Communications Mining™:
See how to accelerate model training and optimize model performance with active learning
Learn about the latest enhancements to out-of-the-box document processing – with little to no training required
Get an exclusive demo of the new family of UiPath LLMs – GenAI models specialized for processing different types of documents and messages
This is a hands-on session specifically designed for automation developers and AI enthusiasts seeking to enhance their knowledge in leveraging the latest intelligent document processing capabilities offered by UiPath.
Speakers:
👨🏫 Andras Palfi, Senior Product Manager, UiPath
👩🏫 Lenka Dulovicova, Product Program Manager, UiPath
UiPath Test Automation using UiPath Test Suite series, part 3DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 3. In this session, we will cover desktop automation along with UI automation.
Topics covered:
UI automation Introduction,
UI automation Sample
Desktop automation flow
Pradeep Chinnala, Senior Consultant Automation Developer @WonderBotz and UiPath MVP
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
Key Trends Shaping the Future of Infrastructure.pdfCheryl Hung
Keynote at DIGIT West Expo, Glasgow on 29 May 2024.
Cheryl Hung, ochery.com
Sr Director, Infrastructure Ecosystem, Arm.
The key trends across hardware, cloud and open-source; exploring how these areas are likely to mature and develop over the short and long-term, and then considering how organisations can position themselves to adapt and thrive.
Epistemic Interaction - tuning interfaces to provide information for AI supportAlan Dix
Paper presented at SYNERGY workshop at AVI 2024, Genoa, Italy. 3rd June 2024
https://alandix.com/academic/papers/synergy2024-epistemic/
As machine learning integrates deeper into human-computer interactions, the concept of epistemic interaction emerges, aiming to refine these interactions to enhance system adaptability. This approach encourages minor, intentional adjustments in user behaviour to enrich the data available for system learning. This paper introduces epistemic interaction within the context of human-system communication, illustrating how deliberate interaction design can improve system understanding and adaptation. Through concrete examples, we demonstrate the potential of epistemic interaction to significantly advance human-computer interaction by leveraging intuitive human communication strategies to inform system design and functionality, offering a novel pathway for enriching user-system engagements.
Securing your Kubernetes cluster_ a step-by-step guide to success !KatiaHIMEUR1
Today, after several years of existence, an extremely active community and an ultra-dynamic ecosystem, Kubernetes has established itself as the de facto standard in container orchestration. Thanks to a wide range of managed services, it has never been so easy to set up a ready-to-use Kubernetes cluster.
However, this ease of use means that the subject of security in Kubernetes is often left for later, or even neglected. This exposes companies to significant risks.
In this talk, I'll show you step-by-step how to secure your Kubernetes cluster for greater peace of mind and reliability.
GraphRAG is All You need? LLM & Knowledge GraphGuy Korland
Guy Korland, CEO and Co-founder of FalkorDB, will review two articles on the integration of language models with knowledge graphs.
1. Unifying Large Language Models and Knowledge Graphs: A Roadmap.
https://arxiv.org/abs/2306.08302
2. Microsoft Research's GraphRAG paper and a review paper on various uses of knowledge graphs:
https://www.microsoft.com/en-us/research/blog/graphrag-unlocking-llm-discovery-on-narrative-private-data/
Accelerate your Kubernetes clusters with Varnish CachingThijs Feryn
A presentation about the usage and availability of Varnish on Kubernetes. This talk explores the capabilities of Varnish caching and shows how to use the Varnish Helm chart to deploy it to Kubernetes.
This presentation was delivered at K8SUG Singapore. See https://feryn.eu/presentations/accelerate-your-kubernetes-clusters-with-varnish-caching-k8sug-singapore-28-2024 for more details.
DevOps and Testing slides at DASA ConnectKari Kakkonen
My and Rik Marselis slides at 30.5.2024 DASA Connect conference. We discuss about what is testing, then what is agile testing and finally what is Testing in DevOps. Finally we had lovely workshop with the participants trying to find out different ways to think about quality and testing in different parts of the DevOps infinity loop.
Essentials of Automations: Optimizing FME Workflows with ParametersSafe Software
Are you looking to streamline your workflows and boost your projects’ efficiency? Do you find yourself searching for ways to add flexibility and control over your FME workflows? If so, you’re in the right place.
Join us for an insightful dive into the world of FME parameters, a critical element in optimizing workflow efficiency. This webinar marks the beginning of our three-part “Essentials of Automation” series. This first webinar is designed to equip you with the knowledge and skills to utilize parameters effectively: enhancing the flexibility, maintainability, and user control of your FME projects.
Here’s what you’ll gain:
- Essentials of FME Parameters: Understand the pivotal role of parameters, including Reader/Writer, Transformer, User, and FME Flow categories. Discover how they are the key to unlocking automation and optimization within your workflows.
- Practical Applications in FME Form: Delve into key user parameter types including choice, connections, and file URLs. Allow users to control how a workflow runs, making your workflows more reusable. Learn to import values and deliver the best user experience for your workflows while enhancing accuracy.
- Optimization Strategies in FME Flow: Explore the creation and strategic deployment of parameters in FME Flow, including the use of deployment and geometry parameters, to maximize workflow efficiency.
- Pro Tips for Success: Gain insights on parameterizing connections and leveraging new features like Conditional Visibility for clarity and simplicity.
We’ll wrap up with a glimpse into future webinars, followed by a Q&A session to address your specific questions surrounding this topic.
Don’t miss this opportunity to elevate your FME expertise and drive your projects to new heights of efficiency.
Software Delivery At the Speed of AI: Inflectra Invests In AI-Powered QualityInflectra
In this insightful webinar, Inflectra explores how artificial intelligence (AI) is transforming software development and testing. Discover how AI-powered tools are revolutionizing every stage of the software development lifecycle (SDLC), from design and prototyping to testing, deployment, and monitoring.
Learn about:
• The Future of Testing: How AI is shifting testing towards verification, analysis, and higher-level skills, while reducing repetitive tasks.
• Test Automation: How AI-powered test case generation, optimization, and self-healing tests are making testing more efficient and effective.
• Visual Testing: Explore the emerging capabilities of AI in visual testing and how it's set to revolutionize UI verification.
• Inflectra's AI Solutions: See demonstrations of Inflectra's cutting-edge AI tools like the ChatGPT plugin and Azure Open AI platform, designed to streamline your testing process.
Whether you're a developer, tester, or QA professional, this webinar will give you valuable insights into how AI is shaping the future of software delivery.