Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
SPS High Voltage Cable Termination Kit List (Typical) - Three Core Cables
XLPE EPR HV Termination Kits
Anti-track heat shrink 3 core tubes x 3
Stress control heat shrink 3 core tubes x 3
Yellow stress relief tape for screen ends x 3
3 core heat shrink cable breakout boot x 1
Red mastic sealing tape x 1
Cable cleaning and de-greasing wipes x 3
Box, label, jointing instructions x 1
HV Termination Kits Optional Extras, 3 Core 6.6-7.2kV - Solderless Earth Kit for Copper Tape Screen Cables, Insulating Bushing Boots (Straight, Right Angled, Universal), HV Cable Glands for SWA Cable (Bolt-on Top Hat), Outdoor Armour Earthing Kit, Outdoor Stand-off Brackets + Insulators, High Voltage HV Cable Lugs (Crimp or Mechanical Shearbolt Lugs).
SPS High Voltage Heat Shrink Cable Termination Kits, 6.6-7.2kV - Testing
SPS high voltage heat shrink termination kits for 3 core HV cables (XLPE and EPR) are Tested and Certified to latest International Test Standards as outlined in Cenelec standards HD 628 S1 and 629.1 S2 : 2006 - high voltage cable termination kit testing also encompasses VDE 0278 and IEC 60502.
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
SPS High Voltage Cable Termination Kit List (Typical) - Three Core Cables
XLPE EPR HV Termination Kits
Anti-track heat shrink 3 core tubes x 3
Stress control heat shrink 3 core tubes x 3
Yellow stress relief tape for screen ends x 3
3 core heat shrink cable breakout boot x 1
Red mastic sealing tape x 1
Cable cleaning and de-greasing wipes x 3
Box, label, jointing instructions x 1
HV Termination Kits Optional Extras, 3 Core 6.6-7.2kV - Solderless Earth Kit for Copper Tape Screen Cables, Insulating Bushing Boots (Straight, Right Angled, Universal), HV Cable Glands for SWA Cable (Bolt-on Top Hat), Outdoor Armour Earthing Kit, Outdoor Stand-off Brackets + Insulators, High Voltage HV Cable Lugs (Crimp or Mechanical Shearbolt Lugs).
SPS High Voltage Heat Shrink Cable Termination Kits, 6.6-7.2kV - Testing
SPS high voltage heat shrink termination kits for 3 core HV cables (XLPE and EPR) are Tested and Certified to latest International Test Standards as outlined in Cenelec standards HD 628 S1 and 629.1 S2 : 2006 - high voltage cable termination kit testing also encompasses VDE 0278 and IEC 60502.
600 Series Interface D Compact Elastimold Cable Connectors and Bushings connect and terminate HV cables to Interface D bushings on switchgear and transformers. Elastimold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F. Elastimold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
600 Series Interface D, Elastimold Bushings
* Bushing Voltage Range 12kV-24kV
* Bushing Current Rating 800Amps
* Bushing Type 5/8"
Bolted Aluminium Stud Elastimold separable elbow connectors are high voltage cable terminations used to connect polymeric (XLPE or EPR insulated) power cables to HV equipment including transformers, switchgear, capacitors and motors. 600 Series Connectors - 676LRA Tee Connectors, 12-24kV 1250Amps 35-630sqmm Slip on cable connectors - quick to install to high voltage switchgear and transformers (oil, air and gas insulated) Touchproof cable terminations - made from conductive EPDM rubber, fully screened HV termination for safety One part cable termination - built-in stress relief, insulation and outer semi-conductive layers Maintenance friendly - readily disconnectable cable connector for high voltage maintenance work Compact cable connectors - space-saving HV cable terminations for SF6 gas insulated switchgear (GIS) EPDM rubber cable connectors - resistant to ozone, corona, chemicals, water and atmospheric pollutants Flexibility - Elastimold cable connectors are disconnectable and re-useable. Re-use of the high voltage cable connector permits site re-location of HV electrical equipment without requiring cable re-termination.
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Euromold elbow connectors, Euromold tee connectors, Euromold bushings (oil insulated) and Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series, 400TB 440TB Features :
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
T&D UK with the support of Nexans provide installation training and certification for experienced high voltage cable jointers up to 33kV.
Hellermann Tyton Heat Shrink Cable Boots, Transitions & Moulded Shapes
Hellermann Tyton Helashrink heatshrink boots and moulded shapes in conjunction with specialist heatshrink tubing make it easy to fabricate complete jacketed wire and cable harnessing and interconnection systems.
Hellermann Tyton Helashrink heatshrink boots (straight and right-angled) and moulded shapes are available for the complete range of electrical and electronic harnessing applications. Heat shrink boots and shapes can be sealed with special adhesives and encapsulants to ensure the proper degree of mechanical support, strain relief and environmental protection. Encapsulating the complete harnessing and interconnection system to the desired configuration is easily and neatly accomplished with minimum weight and bulk using Hellermann Tyton Helashrink heat shrink components.
Hellermann Tyton Heat Shrink Moulded Shapes & Boots - Overview....
Hellermann Tyton Helashrink heat shrinkable shapes, end caps and cable break-out boots with and without inner adhesive. Hellermannn Tyton heat shrink backshells, 2-way outlet shapes, 3-way outlet shapes, 4-way outlet shapes, 5-way outlet shapes up to 6-way outlet shapes. Hellermann Tyton heat shrink right angle boot 90°, 45°C angle, T-shapes, Y-outlet, VG-style shapes. Heat shrink cable end caps for low voltage applications, two components epoxy adhesive and hot melt tape.
Heat shrink cable joints to suit PVC, EPR (BS6883) and XLPE (BS5467) multi-core cables up to 3.3kV - the heat shrink cable joint comprises of adhesive lined connector insulation tubes, heavy duty steel wire armour earth cage, armour support rings and clamps and an outer thick wall adhesive lined heat shrink tube.
SPS Heat Shrink Cable Joints & Cable Terminations - Quality Performance Testing : Shrink Polymer Systems heat shrink cable joints and cable termination kits are tested to BS7888 which incorporates Cenelec Standards HD 628 S1 and 629.1 S2 : 2006, DIN VDE0279 and IEC60502.
Elastimold - HV High Voltage Joints, Terminations, Loadbreak & Deadbreak Connectors.
Load Break Elbows
A load break elbow when used with a hot stick can be connected or disconnected at high voltage under load, but can only be used with up to a 250kcmil cable. At 100% insulation level, a 250kcmil is good for 345A in underground duct, so you would be de-rating your system by using a 200A elbow with a 250kcmil cable, but they are still widely used due to the flexibility given to the high voltage distribution system at the equipment. Think about it…if you had a critical application where power disruptions were extremely costly and maintenance was required on up-stream equipment in, let’s say a non critical area, this product would be great. You could disconnect the load without disturbing the critical portions, perform the maintenance and then reconnect it. Just make sure to take safety precautions, making and breaking electrical connections under load is very dangerous. The load break elbow is typically not used in man-holes, because it does not allow expansion like the dead break elbow. The construction of the load break elbow does not allow it to be connected to other elbows, but the dead break does.
Dead Break Elbows
A dead break or “hammerhead” elbow can only be disconnected when not under load, this is because you need to actually unscrew a pin to detach it. It would be pretty tough to unscrew the pin with a hot stick and the arc from the disconnected load, if under load, would be pretty substantial. A dead break elbow allows an increased current rating (up to 600A) and can be used on basically all cable types. At 100% insulation level a 750kcmil cable is rated 610A in underground duct. When would you use a 750kcmil? In most non-utility cases you would design or install sets of 500kcmil or smaller if you needed more than one 500kcmil could handle. Even from a 1200A breaker, two sets of 500kcmil per phase would be sufficient for distribution (about 1000A), if the load was even that high. Most of the time you set the relays down to the actual load in order to limit the copper used. A dead break when used in man-holes for splicing cables allows the flexibility of connecting more than two cables together as well as future expansion if required. Say another building was added that needed power, you could just connect that building to the existing array of dead break elbows. This also works great when temporary power is needed for construction or even if the circus is in town and they need medium voltage (it happens!). They can pick up power from the man-hole with the dead break elbows or from a piece of equipment with dead break elbows. I’ve heard that ships are now starting to use medium voltage shore power, I wonder what kind of connections they use.
瑞侃工具包电缆终端-阿克巴交易
케이블 종단-거
TERMINAZIONE DEL CAVO - AKBAR TRADING
TERMINACIÓN DE CABLE - AKBAR TRADING
KABELABSCHLUSS
TERMINACIÓN DE CABLE
KABLO SONLANDIRMA
600 Series Interface D Compact Elastimold Cable Connectors and Bushings connect and terminate HV cables to Interface D bushings on switchgear and transformers. Elastimold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F. Elastimold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
600 Series Interface D, Elastimold Bushings
* Bushing Voltage Range 12kV-24kV
* Bushing Current Rating 800Amps
* Bushing Type 5/8"
Bolted Aluminium Stud Elastimold separable elbow connectors are high voltage cable terminations used to connect polymeric (XLPE or EPR insulated) power cables to HV equipment including transformers, switchgear, capacitors and motors. 600 Series Connectors - 676LRA Tee Connectors, 12-24kV 1250Amps 35-630sqmm Slip on cable connectors - quick to install to high voltage switchgear and transformers (oil, air and gas insulated) Touchproof cable terminations - made from conductive EPDM rubber, fully screened HV termination for safety One part cable termination - built-in stress relief, insulation and outer semi-conductive layers Maintenance friendly - readily disconnectable cable connector for high voltage maintenance work Compact cable connectors - space-saving HV cable terminations for SF6 gas insulated switchgear (GIS) EPDM rubber cable connectors - resistant to ozone, corona, chemicals, water and atmospheric pollutants Flexibility - Elastimold cable connectors are disconnectable and re-useable. Re-use of the high voltage cable connector permits site re-location of HV electrical equipment without requiring cable re-termination.
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Euromold elbow connectors, Euromold tee connectors, Euromold bushings (oil insulated) and Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series, 400TB 440TB Features :
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
T&D UK with the support of Nexans provide installation training and certification for experienced high voltage cable jointers up to 33kV.
Hellermann Tyton Heat Shrink Cable Boots, Transitions & Moulded Shapes
Hellermann Tyton Helashrink heatshrink boots and moulded shapes in conjunction with specialist heatshrink tubing make it easy to fabricate complete jacketed wire and cable harnessing and interconnection systems.
Hellermann Tyton Helashrink heatshrink boots (straight and right-angled) and moulded shapes are available for the complete range of electrical and electronic harnessing applications. Heat shrink boots and shapes can be sealed with special adhesives and encapsulants to ensure the proper degree of mechanical support, strain relief and environmental protection. Encapsulating the complete harnessing and interconnection system to the desired configuration is easily and neatly accomplished with minimum weight and bulk using Hellermann Tyton Helashrink heat shrink components.
Hellermann Tyton Heat Shrink Moulded Shapes & Boots - Overview....
Hellermann Tyton Helashrink heat shrinkable shapes, end caps and cable break-out boots with and without inner adhesive. Hellermannn Tyton heat shrink backshells, 2-way outlet shapes, 3-way outlet shapes, 4-way outlet shapes, 5-way outlet shapes up to 6-way outlet shapes. Hellermann Tyton heat shrink right angle boot 90°, 45°C angle, T-shapes, Y-outlet, VG-style shapes. Heat shrink cable end caps for low voltage applications, two components epoxy adhesive and hot melt tape.
Heat shrink cable joints to suit PVC, EPR (BS6883) and XLPE (BS5467) multi-core cables up to 3.3kV - the heat shrink cable joint comprises of adhesive lined connector insulation tubes, heavy duty steel wire armour earth cage, armour support rings and clamps and an outer thick wall adhesive lined heat shrink tube.
SPS Heat Shrink Cable Joints & Cable Terminations - Quality Performance Testing : Shrink Polymer Systems heat shrink cable joints and cable termination kits are tested to BS7888 which incorporates Cenelec Standards HD 628 S1 and 629.1 S2 : 2006, DIN VDE0279 and IEC60502.
Elastimold - HV High Voltage Joints, Terminations, Loadbreak & Deadbreak Connectors.
Load Break Elbows
A load break elbow when used with a hot stick can be connected or disconnected at high voltage under load, but can only be used with up to a 250kcmil cable. At 100% insulation level, a 250kcmil is good for 345A in underground duct, so you would be de-rating your system by using a 200A elbow with a 250kcmil cable, but they are still widely used due to the flexibility given to the high voltage distribution system at the equipment. Think about it…if you had a critical application where power disruptions were extremely costly and maintenance was required on up-stream equipment in, let’s say a non critical area, this product would be great. You could disconnect the load without disturbing the critical portions, perform the maintenance and then reconnect it. Just make sure to take safety precautions, making and breaking electrical connections under load is very dangerous. The load break elbow is typically not used in man-holes, because it does not allow expansion like the dead break elbow. The construction of the load break elbow does not allow it to be connected to other elbows, but the dead break does.
Dead Break Elbows
A dead break or “hammerhead” elbow can only be disconnected when not under load, this is because you need to actually unscrew a pin to detach it. It would be pretty tough to unscrew the pin with a hot stick and the arc from the disconnected load, if under load, would be pretty substantial. A dead break elbow allows an increased current rating (up to 600A) and can be used on basically all cable types. At 100% insulation level a 750kcmil cable is rated 610A in underground duct. When would you use a 750kcmil? In most non-utility cases you would design or install sets of 500kcmil or smaller if you needed more than one 500kcmil could handle. Even from a 1200A breaker, two sets of 500kcmil per phase would be sufficient for distribution (about 1000A), if the load was even that high. Most of the time you set the relays down to the actual load in order to limit the copper used. A dead break when used in man-holes for splicing cables allows the flexibility of connecting more than two cables together as well as future expansion if required. Say another building was added that needed power, you could just connect that building to the existing array of dead break elbows. This also works great when temporary power is needed for construction or even if the circus is in town and they need medium voltage (it happens!). They can pick up power from the man-hole with the dead break elbows or from a piece of equipment with dead break elbows. I’ve heard that ships are now starting to use medium voltage shore power, I wonder what kind of connections they use.
瑞侃工具包电缆终端-阿克巴交易
케이블 종단-거
TERMINAZIONE DEL CAVO - AKBAR TRADING
TERMINACIÓN DE CABLE - AKBAR TRADING
KABELABSCHLUSS
TERMINACIÓN DE CABLE
KABLO SONLANDIRMA
Craig and Derricott Isolators
Isolation Equipment and Switch Disconnectors
Moulded Plastic Isolators & Switch Disconnectors IP65 20A-63A
Mild Steel Isolators & Switch Disconnectors IP65 20A-63A
Stainless Steel Isolators & Switch Disconnectors IP65 20A-63A
Die Cast Isolators & Switch Disconnectors IP65 20A-63A
Sheet Steel Isolators & Switch Disconnectors IP41 32A-630A
Sheet Steel Isolators & Switch Disconnectors IP65 32A-1000A
ATEX Zone 22 Isolators& Switch Disconnectors Cat 3D
Fire Rated Isolators & Switch Disconnectors 20A-125A
Isolation Equipment and Switch Disconnectors
Craig & Derricott Section 12 London Underground Isolators
Craig & Derricott Stainless Steel Water Utility Isolators
Lucy Lighting Street Lighting Trojan Isolators
Switch Disconnectors (Isolators) provide the means to safely disconnect or isolate an item of electrical equipment from the power supply - primarily designed to provide a means of local isolation when an elecrical item may need maintenance or repair. Switch Disconnectors also i) provide an effective clearance between the supply and the electrical load appropriate to the voltage applied, ii) provide a means of "locking off" (padlocking), iii) provide true indication of contact state, iv) provide a safe electrical disconnection from the power supply even under fault conditions.
Shrink Polymer Systems high voltage (HV) heat shrink cable joints, cable terminations and busbar tape and tubings for 6.6kV, 11kV, 24kV and 33kV.
SPS HV Cable Joints - Straight, transition, pot-end, trifurcating and branch cable joints for both polymeric and paper cables, 11kV-33kV.
SPS HV Cable Terminations - Single and 3 core, indoor and outdoor high voltage cable terminations for both polymeric and paper cables, 11kV-33kV.
SPS 6.6kV, 11kV and 33kV heat shrink cable joint kits and cable termination kits are quick and easy to install by trained HV jointers providing high reliability and excellent performance for high voltage cable circuits. SPS heat shrink cable termination and joint kits are suitable for three and single core XLPE, EPR and PILC cables, including utility specification Triplex cables 11kV-33kV.
SPS heat shrink cable joints and cable terminations are Tested to International Standards outlined in Cenelec HD 628 S1 and 629.1 S2 : 2006 - encompassing VDE 0278 and IEC 60502 - peace of mind performance.
THORNE & DERRICK UK are Exclusive UK Distributors for SPS Shrink Polymer Systems. T&D SPS provide the most competitive prices, largest stocks and first class service for LV-HV cable joints, cable terminations and accessories up to 33kV.
Tested to Cenelec, VDE, IEC Standards - save time and money without compromising high voltage cable installations.
T&D supply LV-HV Cable Accessories, Cable Jointing & Electrical Eqpt - we service UK and global contractors involved in cable installations, cable jointing, substation and electrical construction at LV, 11kV, 33kV and EHV. We export to utilities, power, construction, rail, mining, offshore, oil, gas and petrochemical industries.
Kraus & naimer main switches and maintenance switches kn500 gb1214Dien Ha The
Catalog Kraus Naimer, Catalog,
Catalog Thiết Bị Điện Kraus Naimer, Catalog Thiết Bị Điện,
Catalog Biến Tần Kraus Naimer, Catalog Điện Công Nghiệp,
http://dienhathe.com,
Chi tiết các sản phẩm khác của Kraus Naimer tại https://dienhathe.com
Xem thêm các Catalog khác của Kraus Naimer tại https://dienhathe.info
Để nhận báo giá sản phẩm Kraus Naimer vui lòng gọi: 0907.764.966
Kraus & naimer main switches and maintenance switches kn500 gb1214-dienha...Dien Ha The
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.org
3M Earthing Kits & Constant Force Springs | AKBAR TRADING EST. - mail@akbart...AKBAR TRADING
3M™ AC Series - Armour Continuity Kits
This Scotchcast™ Armour Continuity Kit is designed to provide complete electrical
continuity across the joint position on 2, 3 or 4 core armoured power cables for inline, tee
or branch configurations.
The AC kits contain two interlocking contact rings and two lengths of steel band with preassembled
buckles. Used in conjunction with an ACC kit containing the required length of
copper cord.
The JO20 ‘Pok-It’ Tool is used to assemble the components and ensure low contact
Band it Pok it Tool
Pok-It II Tool J020 is a lightweight pocket sized tool for use with 3M AC Series Kit. Applies
tension and includes built-in cutter. Weight 1.1lbs (.5kg).
Electrical Grounding Braid
Bonding Kits
Constant Force Springs
RAYCHEM SAUDI ARABIA LTD. (TYCO ELECTRONICS) |AKBAR TRADING EST. SAUDI ARABIA...AKBAR TRADING
te connectivity saudi arabia
TYCO TERMINATION KIT IN ALL VOLTAGE
Raychem terminations for polymeric and MIND
paper insulated cables from 7.2 kV up to 36 kV
System Designer
케이블 종단-거-瑞侃工具包电缆终端-阿克巴交易
ชุด การเลิกจ้าง
RAYCHEM SAUDI ARABIA LTD. (TYCO ELECTRONICS)
11kV-33kV Medium Voltage Heat Shrink Cable Joints & Cable Terminations
11kV and 33kV heat shrink cable joints and cable terminations for medium voltage power cables - SPS heat shrink cable joints and cable terminations are suitable for installation at indoors and outdoors in the Middle East countries, this includes salt laden and dusty atmospheres associated with the Middle East oil, gas and petrochemical industries. Cable terminations and cable joints are suitable for XLPE and paper insulated single core and three 3 core cables of 11kV and 33kV voltages, 3 phase, 50HZ type electrical systems with highest system voltages of 12kV and 36kV. Cable joints are suitable for connecting two XLPE insulated cables of same size or dissimilar sizes and for transition between XLPE and paper insulated lead covered (PILC) medium voltage cables.
Isolation Procedures for Safe Working on Electrical Systems and Equipment by the JIB | solation Procedures for Safe Working on Electrical Systems and Equipment
This chart shows the safe isolation procedure that you should use when working on electrical systems and equipment.
You'll receive a printed copy of this from your Training Provider, but it's also here as a handy reference to keep electronically.
THE RULES OF SAFE ISOLATION ARE:
Obtain permission to start work (a Permit may be required in some situations)
Identify the source(s) of supply using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Isolate the supply(s)
Secure the isolation
Prove the system/equipment is DEAD using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Put up warning signs to tell other people that the electrical installation has been isolated
Once the system/equipment is proved DEAD, work can begin
Uploaded by THORNE & DERRICK LV HV Jointing, Earthing, Substation & Electrical Eqpt | Explosive Atmosphere Experts & ATEX IECEx.
THORNE & DERRICK based in the UK are international distributors of LV, MV & HV Cable Installation, Jointing, Substation & Electrical Equipment.
Since 1985, T&D have established an international reputation based on SERVICE | INTEGRITY | TRUST.
Contact us for 3M, ABB, Alroc, AN Wallis, CATU, Cembre, Centriforce, CMP, CSD, Elastimold, Ellis Patents, Emtelle, Euromold, Filoform , Furse, Lucy Electric & Zodion, Nexans, Pfisterer, Polypipe, Prysmian, Roxtec, Sicame, WT Henley.
Elevating Tactical DDD Patterns Through Object CalisthenicsDorra BARTAGUIZ
After immersing yourself in the blue book and its red counterpart, attending DDD-focused conferences, and applying tactical patterns, you're left with a crucial question: How do I ensure my design is effective? Tactical patterns within Domain-Driven Design (DDD) serve as guiding principles for creating clear and manageable domain models. However, achieving success with these patterns requires additional guidance. Interestingly, we've observed that a set of constraints initially designed for training purposes remarkably aligns with effective pattern implementation, offering a more ‘mechanical’ approach. Let's explore together how Object Calisthenics can elevate the design of your tactical DDD patterns, offering concrete help for those venturing into DDD for the first time!
Kubernetes & AI - Beauty and the Beast !?! @KCD Istanbul 2024Tobias Schneck
As AI technology is pushing into IT I was wondering myself, as an “infrastructure container kubernetes guy”, how get this fancy AI technology get managed from an infrastructure operational view? Is it possible to apply our lovely cloud native principals as well? What benefit’s both technologies could bring to each other?
Let me take this questions and provide you a short journey through existing deployment models and use cases for AI software. On practical examples, we discuss what cloud/on-premise strategy we may need for applying it to our own infrastructure to get it to work from an enterprise perspective. I want to give an overview about infrastructure requirements and technologies, what could be beneficial or limiting your AI use cases in an enterprise environment. An interactive Demo will give you some insides, what approaches I got already working for real.
LF Energy Webinar: Electrical Grid Modelling and Simulation Through PowSyBl -...DanBrown980551
Do you want to learn how to model and simulate an electrical network from scratch in under an hour?
Then welcome to this PowSyBl workshop, hosted by Rte, the French Transmission System Operator (TSO)!
During the webinar, you will discover the PowSyBl ecosystem as well as handle and study an electrical network through an interactive Python notebook.
PowSyBl is an open source project hosted by LF Energy, which offers a comprehensive set of features for electrical grid modelling and simulation. Among other advanced features, PowSyBl provides:
- A fully editable and extendable library for grid component modelling;
- Visualization tools to display your network;
- Grid simulation tools, such as power flows, security analyses (with or without remedial actions) and sensitivity analyses;
The framework is mostly written in Java, with a Python binding so that Python developers can access PowSyBl functionalities as well.
What you will learn during the webinar:
- For beginners: discover PowSyBl's functionalities through a quick general presentation and the notebook, without needing any expert coding skills;
- For advanced developers: master the skills to efficiently apply PowSyBl functionalities to your real-world scenarios.
Encryption in Microsoft 365 - ExpertsLive Netherlands 2024Albert Hoitingh
In this session I delve into the encryption technology used in Microsoft 365 and Microsoft Purview. Including the concepts of Customer Key and Double Key Encryption.
Neuro-symbolic is not enough, we need neuro-*semantic*Frank van Harmelen
Neuro-symbolic (NeSy) AI is on the rise. However, simply machine learning on just any symbolic structure is not sufficient to really harvest the gains of NeSy. These will only be gained when the symbolic structures have an actual semantics. I give an operational definition of semantics as “predictable inference”.
All of this illustrated with link prediction over knowledge graphs, but the argument is general.
Essentials of Automations: Optimizing FME Workflows with ParametersSafe Software
Are you looking to streamline your workflows and boost your projects’ efficiency? Do you find yourself searching for ways to add flexibility and control over your FME workflows? If so, you’re in the right place.
Join us for an insightful dive into the world of FME parameters, a critical element in optimizing workflow efficiency. This webinar marks the beginning of our three-part “Essentials of Automation” series. This first webinar is designed to equip you with the knowledge and skills to utilize parameters effectively: enhancing the flexibility, maintainability, and user control of your FME projects.
Here’s what you’ll gain:
- Essentials of FME Parameters: Understand the pivotal role of parameters, including Reader/Writer, Transformer, User, and FME Flow categories. Discover how they are the key to unlocking automation and optimization within your workflows.
- Practical Applications in FME Form: Delve into key user parameter types including choice, connections, and file URLs. Allow users to control how a workflow runs, making your workflows more reusable. Learn to import values and deliver the best user experience for your workflows while enhancing accuracy.
- Optimization Strategies in FME Flow: Explore the creation and strategic deployment of parameters in FME Flow, including the use of deployment and geometry parameters, to maximize workflow efficiency.
- Pro Tips for Success: Gain insights on parameterizing connections and leveraging new features like Conditional Visibility for clarity and simplicity.
We’ll wrap up with a glimpse into future webinars, followed by a Q&A session to address your specific questions surrounding this topic.
Don’t miss this opportunity to elevate your FME expertise and drive your projects to new heights of efficiency.
JMeter webinar - integration with InfluxDB and GrafanaRTTS
Watch this recorded webinar about real-time monitoring of application performance. See how to integrate Apache JMeter, the open-source leader in performance testing, with InfluxDB, the open-source time-series database, and Grafana, the open-source analytics and visualization application.
In this webinar, we will review the benefits of leveraging InfluxDB and Grafana when executing load tests and demonstrate how these tools are used to visualize performance metrics.
Length: 30 minutes
Session Overview
-------------------------------------------
During this webinar, we will cover the following topics while demonstrating the integrations of JMeter, InfluxDB and Grafana:
- What out-of-the-box solutions are available for real-time monitoring JMeter tests?
- What are the benefits of integrating InfluxDB and Grafana into the load testing stack?
- Which features are provided by Grafana?
- Demonstration of InfluxDB and Grafana using a practice web application
To view the webinar recording, go to:
https://www.rttsweb.com/jmeter-integration-webinar
Slack (or Teams) Automation for Bonterra Impact Management (fka Social Soluti...Jeffrey Haguewood
Sidekick Solutions uses Bonterra Impact Management (fka Social Solutions Apricot) and automation solutions to integrate data for business workflows.
We believe integration and automation are essential to user experience and the promise of efficient work through technology. Automation is the critical ingredient to realizing that full vision. We develop integration products and services for Bonterra Case Management software to support the deployment of automations for a variety of use cases.
This video focuses on the notifications, alerts, and approval requests using Slack for Bonterra Impact Management. The solutions covered in this webinar can also be deployed for Microsoft Teams.
Interested in deploying notification automations for Bonterra Impact Management? Contact us at sales@sidekicksolutionsllc.com to discuss next steps.
Accelerate your Kubernetes clusters with Varnish CachingThijs Feryn
A presentation about the usage and availability of Varnish on Kubernetes. This talk explores the capabilities of Varnish caching and shows how to use the Varnish Helm chart to deploy it to Kubernetes.
This presentation was delivered at K8SUG Singapore. See https://feryn.eu/presentations/accelerate-your-kubernetes-clusters-with-varnish-caching-k8sug-singapore-28-2024 for more details.
AI for Every Business: Unlocking Your Product's Universal Potential by VP of ...
Craig & Derricott 25A Disconnectors - 2,3,4,6 Pole
1. T e c h n i c a l D a t a S h e e t
London Underground Station Upgrade - 25A Die-cast Isolators
Craig & Derricott Ltd
Hall Lane, Walsall Wood,
Walsall, West Midlands WS9 9DP
t: +44(0)1543 375541 f: +44(0)1543 361619
e: sales@craigandderricott.com
craigandderricott.com
page 1
25A Switch Disconnectors
Die-cast Enclosures Finished in Dark Admiralty Grey
The die-cast range of switch disconnectors from Craig &
Derricott provides the ultimate in strength and flexibility for
today's industrial installations.
Available in both 25A and 40A ratings, the options available
will cover the majority of applications found in a typical site
project.
Years of being at the forefront of switch disconnector
manufacture has enabled us to provide the very best in
quality and reliability.
• Ratings to BS EN 60947-3
Ithe 25A, AC23A : 9.5kW at 415V.
• Standard items available in 2, 3, 4 and 6 poles.
3 and 6 pole options with 2 early break (E/B)
auxiliaries.
• Captive lid fixing screws with security head.
• 2 x M20 tapped cable entries (1 off plugged)
• Enclosure material - Aluminium (LM6).
• Sealing to IP65.
• Paint Finishes -
Copon 35TR or 38TR systems
Colour - Dark Admiralty Grey* 381 C632HG
• Supplied with pre-finished steel mounting brackets
• Neutral links form part of the switch interior.
• Padlocking cast lever.
• Positive break contacts.
• A maximum of 8 contacts available in the 20A size.
• Earthing points in both lid and enclosure base plus
external M6 earth terminal.
• Padlocking in both ‘On’ & ‘Off’ positions
• Labels - Engraved traffolyte labels in various colours
can be supplied attached to the side of the
enclosure, or supplied loose for fitting adjacent to
the isolator.
• Second product label supplied loose for fitting by
contractor where original label may be obscured.
Features:-
Configuration Catalogue Number
2 Pole DCG252LUL10
3 Pole DCG253LUL10
3 Pole + 2 E/B Aux. DCG253EBLUL10
4 Pole DCG254LUL10
6 Pole DCG256LUL10
6 Pole + 2 E/B Aux. DCG256EBLUL10
Ordering Information:-
"
Dimensions:-
Termination - M4
Maximum Cable Size - 2.5 to 6.0mm2
External Fixings - M6
Weight - Approx. 1.4kg
Overall Depth - 120
2 off M20 Entries
WWW.CABLEJOINTS.CO.UK
THORNE & DERRICK UK
TEL 0044 191 490 1547 FAX 0044 477 5371
TEL 0044 117 977 4647 FAX 0044 977 5582
WWW.THORNEANDDERRICK.CO.UK