Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
Shrink Polymer Systems high voltage (HV) heat shrink cable joints, cable terminations and busbar tape and tubings for 6.6kV, 11kV, 24kV and 33kV.
SPS HV Cable Joints - Straight, transition, pot-end, trifurcating and branch cable joints for both polymeric and paper cables, 11kV-33kV.
SPS HV Cable Terminations - Single and 3 core, indoor and outdoor high voltage cable terminations for both polymeric and paper cables, 11kV-33kV.
SPS 6.6kV, 11kV and 33kV heat shrink cable joint kits and cable termination kits are quick and easy to install by trained HV jointers providing high reliability and excellent performance for high voltage cable circuits. SPS heat shrink cable termination and joint kits are suitable for three and single core XLPE, EPR and PILC cables, including utility specification Triplex cables 11kV-33kV.
SPS heat shrink cable joints and cable terminations are Tested to International Standards outlined in Cenelec HD 628 S1 and 629.1 S2 : 2006 - encompassing VDE 0278 and IEC 60502 - peace of mind performance.
THORNE & DERRICK UK are Exclusive UK Distributors for SPS Shrink Polymer Systems. T&D SPS provide the most competitive prices, largest stocks and first class service for LV-HV cable joints, cable terminations and accessories up to 33kV.
Tested to Cenelec, VDE, IEC Standards - save time and money without compromising high voltage cable installations.
T&D supply LV-HV Cable Accessories, Cable Jointing & Electrical Eqpt - we service UK and global contractors involved in cable installations, cable jointing, substation and electrical construction at LV, 11kV, 33kV and EHV. We export to utilities, power, construction, rail, mining, offshore, oil, gas and petrochemical industries.
SPS High Voltage Cable Termination Kit List (Typical) - Three Core Cables
XLPE EPR HV Termination Kits
Anti-track heat shrink 3 core tubes x 3
Stress control heat shrink 3 core tubes x 3
Yellow stress relief tape for screen ends x 3
3 core heat shrink cable breakout boot x 1
Red mastic sealing tape x 1
Cable cleaning and de-greasing wipes x 3
Box, label, jointing instructions x 1
HV Termination Kits Optional Extras, 3 Core 6.6-7.2kV - Solderless Earth Kit for Copper Tape Screen Cables, Insulating Bushing Boots (Straight, Right Angled, Universal), HV Cable Glands for SWA Cable (Bolt-on Top Hat), Outdoor Armour Earthing Kit, Outdoor Stand-off Brackets + Insulators, High Voltage HV Cable Lugs (Crimp or Mechanical Shearbolt Lugs).
SPS High Voltage Heat Shrink Cable Termination Kits, 6.6-7.2kV - Testing
SPS high voltage heat shrink termination kits for 3 core HV cables (XLPE and EPR) are Tested and Certified to latest International Test Standards as outlined in Cenelec standards HD 628 S1 and 629.1 S2 : 2006 - high voltage cable termination kit testing also encompasses VDE 0278 and IEC 60502.
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
Shrink Polymer Systems high voltage (HV) heat shrink cable joints, cable terminations and busbar tape and tubings for 6.6kV, 11kV, 24kV and 33kV.
SPS HV Cable Joints - Straight, transition, pot-end, trifurcating and branch cable joints for both polymeric and paper cables, 11kV-33kV.
SPS HV Cable Terminations - Single and 3 core, indoor and outdoor high voltage cable terminations for both polymeric and paper cables, 11kV-33kV.
SPS 6.6kV, 11kV and 33kV heat shrink cable joint kits and cable termination kits are quick and easy to install by trained HV jointers providing high reliability and excellent performance for high voltage cable circuits. SPS heat shrink cable termination and joint kits are suitable for three and single core XLPE, EPR and PILC cables, including utility specification Triplex cables 11kV-33kV.
SPS heat shrink cable joints and cable terminations are Tested to International Standards outlined in Cenelec HD 628 S1 and 629.1 S2 : 2006 - encompassing VDE 0278 and IEC 60502 - peace of mind performance.
THORNE & DERRICK UK are Exclusive UK Distributors for SPS Shrink Polymer Systems. T&D SPS provide the most competitive prices, largest stocks and first class service for LV-HV cable joints, cable terminations and accessories up to 33kV.
Tested to Cenelec, VDE, IEC Standards - save time and money without compromising high voltage cable installations.
T&D supply LV-HV Cable Accessories, Cable Jointing & Electrical Eqpt - we service UK and global contractors involved in cable installations, cable jointing, substation and electrical construction at LV, 11kV, 33kV and EHV. We export to utilities, power, construction, rail, mining, offshore, oil, gas and petrochemical industries.
SPS High Voltage Cable Termination Kit List (Typical) - Three Core Cables
XLPE EPR HV Termination Kits
Anti-track heat shrink 3 core tubes x 3
Stress control heat shrink 3 core tubes x 3
Yellow stress relief tape for screen ends x 3
3 core heat shrink cable breakout boot x 1
Red mastic sealing tape x 1
Cable cleaning and de-greasing wipes x 3
Box, label, jointing instructions x 1
HV Termination Kits Optional Extras, 3 Core 6.6-7.2kV - Solderless Earth Kit for Copper Tape Screen Cables, Insulating Bushing Boots (Straight, Right Angled, Universal), HV Cable Glands for SWA Cable (Bolt-on Top Hat), Outdoor Armour Earthing Kit, Outdoor Stand-off Brackets + Insulators, High Voltage HV Cable Lugs (Crimp or Mechanical Shearbolt Lugs).
SPS High Voltage Heat Shrink Cable Termination Kits, 6.6-7.2kV - Testing
SPS high voltage heat shrink termination kits for 3 core HV cables (XLPE and EPR) are Tested and Certified to latest International Test Standards as outlined in Cenelec standards HD 628 S1 and 629.1 S2 : 2006 - high voltage cable termination kit testing also encompasses VDE 0278 and IEC 60502.
600 Series Interface D Compact Elastimold Cable Connectors and Bushings connect and terminate HV cables to Interface D bushings on switchgear and transformers. Elastimold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F. Elastimold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
600 Series Interface D, Elastimold Bushings
* Bushing Voltage Range 12kV-24kV
* Bushing Current Rating 800Amps
* Bushing Type 5/8"
Bolted Aluminium Stud Elastimold separable elbow connectors are high voltage cable terminations used to connect polymeric (XLPE or EPR insulated) power cables to HV equipment including transformers, switchgear, capacitors and motors. 600 Series Connectors - 676LRA Tee Connectors, 12-24kV 1250Amps 35-630sqmm Slip on cable connectors - quick to install to high voltage switchgear and transformers (oil, air and gas insulated) Touchproof cable terminations - made from conductive EPDM rubber, fully screened HV termination for safety One part cable termination - built-in stress relief, insulation and outer semi-conductive layers Maintenance friendly - readily disconnectable cable connector for high voltage maintenance work Compact cable connectors - space-saving HV cable terminations for SF6 gas insulated switchgear (GIS) EPDM rubber cable connectors - resistant to ozone, corona, chemicals, water and atmospheric pollutants Flexibility - Elastimold cable connectors are disconnectable and re-useable. Re-use of the high voltage cable connector permits site re-location of HV electrical equipment without requiring cable re-termination.
Elastimold - HV High Voltage Joints, Terminations, Loadbreak & Deadbreak Connectors.
Load Break Elbows
A load break elbow when used with a hot stick can be connected or disconnected at high voltage under load, but can only be used with up to a 250kcmil cable. At 100% insulation level, a 250kcmil is good for 345A in underground duct, so you would be de-rating your system by using a 200A elbow with a 250kcmil cable, but they are still widely used due to the flexibility given to the high voltage distribution system at the equipment. Think about it…if you had a critical application where power disruptions were extremely costly and maintenance was required on up-stream equipment in, let’s say a non critical area, this product would be great. You could disconnect the load without disturbing the critical portions, perform the maintenance and then reconnect it. Just make sure to take safety precautions, making and breaking electrical connections under load is very dangerous. The load break elbow is typically not used in man-holes, because it does not allow expansion like the dead break elbow. The construction of the load break elbow does not allow it to be connected to other elbows, but the dead break does.
Dead Break Elbows
A dead break or “hammerhead” elbow can only be disconnected when not under load, this is because you need to actually unscrew a pin to detach it. It would be pretty tough to unscrew the pin with a hot stick and the arc from the disconnected load, if under load, would be pretty substantial. A dead break elbow allows an increased current rating (up to 600A) and can be used on basically all cable types. At 100% insulation level a 750kcmil cable is rated 610A in underground duct. When would you use a 750kcmil? In most non-utility cases you would design or install sets of 500kcmil or smaller if you needed more than one 500kcmil could handle. Even from a 1200A breaker, two sets of 500kcmil per phase would be sufficient for distribution (about 1000A), if the load was even that high. Most of the time you set the relays down to the actual load in order to limit the copper used. A dead break when used in man-holes for splicing cables allows the flexibility of connecting more than two cables together as well as future expansion if required. Say another building was added that needed power, you could just connect that building to the existing array of dead break elbows. This also works great when temporary power is needed for construction or even if the circus is in town and they need medium voltage (it happens!). They can pick up power from the man-hole with the dead break elbows or from a piece of equipment with dead break elbows. I’ve heard that ships are now starting to use medium voltage shore power, I wonder what kind of connections they use.
Datamate is the field-proven high-reliability range of choice for many industries, designed with aerospace, military and other “high-end” applications in mind and proven in many years of successful service. It is successfully and internationally utilised in COTS programs. To assist in these fields, Harwin has included a Metal Backshell accessory option, designed to give 360 degree shielding when mated.
400 Series Interface C Compact Nexans Euromold Cable Connectors and Bushings connect and terminate HV cables to Interface C bushings on switchgear and transformers.
Nexans Euromold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F.
Nexans Euromold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
Heat shrink cable joints to suit PVC, EPR (BS6883) and XLPE (BS5467) multi-core cables up to 3.3kV - the heat shrink cable joint comprises of adhesive lined connector insulation tubes, heavy duty steel wire armour earth cage, armour support rings and clamps and an outer thick wall adhesive lined heat shrink tube.
SPS Heat Shrink Cable Joints & Cable Terminations - Quality Performance Testing : Shrink Polymer Systems heat shrink cable joints and cable termination kits are tested to BS7888 which incorporates Cenelec Standards HD 628 S1 and 629.1 S2 : 2006, DIN VDE0279 and IEC60502.
600 Series Interface D Compact Elastimold Cable Connectors and Bushings connect and terminate HV cables to Interface D bushings on switchgear and transformers. Elastimold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F. Elastimold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
600 Series Interface D, Elastimold Bushings
* Bushing Voltage Range 12kV-24kV
* Bushing Current Rating 800Amps
* Bushing Type 5/8"
Bolted Aluminium Stud Elastimold separable elbow connectors are high voltage cable terminations used to connect polymeric (XLPE or EPR insulated) power cables to HV equipment including transformers, switchgear, capacitors and motors. 600 Series Connectors - 676LRA Tee Connectors, 12-24kV 1250Amps 35-630sqmm Slip on cable connectors - quick to install to high voltage switchgear and transformers (oil, air and gas insulated) Touchproof cable terminations - made from conductive EPDM rubber, fully screened HV termination for safety One part cable termination - built-in stress relief, insulation and outer semi-conductive layers Maintenance friendly - readily disconnectable cable connector for high voltage maintenance work Compact cable connectors - space-saving HV cable terminations for SF6 gas insulated switchgear (GIS) EPDM rubber cable connectors - resistant to ozone, corona, chemicals, water and atmospheric pollutants Flexibility - Elastimold cable connectors are disconnectable and re-useable. Re-use of the high voltage cable connector permits site re-location of HV electrical equipment without requiring cable re-termination.
Elastimold - HV High Voltage Joints, Terminations, Loadbreak & Deadbreak Connectors.
Load Break Elbows
A load break elbow when used with a hot stick can be connected or disconnected at high voltage under load, but can only be used with up to a 250kcmil cable. At 100% insulation level, a 250kcmil is good for 345A in underground duct, so you would be de-rating your system by using a 200A elbow with a 250kcmil cable, but they are still widely used due to the flexibility given to the high voltage distribution system at the equipment. Think about it…if you had a critical application where power disruptions were extremely costly and maintenance was required on up-stream equipment in, let’s say a non critical area, this product would be great. You could disconnect the load without disturbing the critical portions, perform the maintenance and then reconnect it. Just make sure to take safety precautions, making and breaking electrical connections under load is very dangerous. The load break elbow is typically not used in man-holes, because it does not allow expansion like the dead break elbow. The construction of the load break elbow does not allow it to be connected to other elbows, but the dead break does.
Dead Break Elbows
A dead break or “hammerhead” elbow can only be disconnected when not under load, this is because you need to actually unscrew a pin to detach it. It would be pretty tough to unscrew the pin with a hot stick and the arc from the disconnected load, if under load, would be pretty substantial. A dead break elbow allows an increased current rating (up to 600A) and can be used on basically all cable types. At 100% insulation level a 750kcmil cable is rated 610A in underground duct. When would you use a 750kcmil? In most non-utility cases you would design or install sets of 500kcmil or smaller if you needed more than one 500kcmil could handle. Even from a 1200A breaker, two sets of 500kcmil per phase would be sufficient for distribution (about 1000A), if the load was even that high. Most of the time you set the relays down to the actual load in order to limit the copper used. A dead break when used in man-holes for splicing cables allows the flexibility of connecting more than two cables together as well as future expansion if required. Say another building was added that needed power, you could just connect that building to the existing array of dead break elbows. This also works great when temporary power is needed for construction or even if the circus is in town and they need medium voltage (it happens!). They can pick up power from the man-hole with the dead break elbows or from a piece of equipment with dead break elbows. I’ve heard that ships are now starting to use medium voltage shore power, I wonder what kind of connections they use.
Datamate is the field-proven high-reliability range of choice for many industries, designed with aerospace, military and other “high-end” applications in mind and proven in many years of successful service. It is successfully and internationally utilised in COTS programs. To assist in these fields, Harwin has included a Metal Backshell accessory option, designed to give 360 degree shielding when mated.
400 Series Interface C Compact Nexans Euromold Cable Connectors and Bushings connect and terminate HV cables to Interface C bushings on switchgear and transformers.
Nexans Euromold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F.
Nexans Euromold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
Heat shrink cable joints to suit PVC, EPR (BS6883) and XLPE (BS5467) multi-core cables up to 3.3kV - the heat shrink cable joint comprises of adhesive lined connector insulation tubes, heavy duty steel wire armour earth cage, armour support rings and clamps and an outer thick wall adhesive lined heat shrink tube.
SPS Heat Shrink Cable Joints & Cable Terminations - Quality Performance Testing : Shrink Polymer Systems heat shrink cable joints and cable termination kits are tested to BS7888 which incorporates Cenelec Standards HD 628 S1 and 629.1 S2 : 2006, DIN VDE0279 and IEC60502.
Nexans Euromold Separable Elbow Connectors 158LR are designed to terminate and connect high voltage polymeric cables to electrical equipment including motors, switchgear and transformers with Type A 250Amp interface as described by CENELEC EN50180 and 50181.
Nexans Euromold Elbow Connectors type 158LR meet the requirements of CENELEC HD 629.1.
Nexans Euromold separable elbow connectors are designed to terminate high voltage polymeric (XLPE EPR) screened (copper wire or copper tape) cables to CENELEC Interface Type A (250amp) bushings with 7.9mm plug-in pins, 11kV-24kV.
Nexans Euromold 158LR/G and Nexans Euromold 158LR seperable connectors are approved for terminating 11kV/12kV polymeric (XLPE EPR) cables into gas insulated (SF6) switchgear, including ABB Safe Ring Ring Main Units (RMU's) and ABB Safe Plus Switchgear. Euromold 158LR/G connectors include earthing leads.
Kraus & naimer main switches and maintenance switches kn500 gb1214Dien Ha The
Catalog Kraus Naimer, Catalog,
Catalog Thiết Bị Điện Kraus Naimer, Catalog Thiết Bị Điện,
Catalog Biến Tần Kraus Naimer, Catalog Điện Công Nghiệp,
http://dienhathe.com,
Chi tiết các sản phẩm khác của Kraus Naimer tại https://dienhathe.com
Xem thêm các Catalog khác của Kraus Naimer tại https://dienhathe.info
Để nhận báo giá sản phẩm Kraus Naimer vui lòng gọi: 0907.764.966
Kraus & naimer main switches and maintenance switches kn500 gb1214-dienha...Dien Ha The
Khoa Học - Kỹ Thuật & Giải Trí: http://phongvan.org
Tài Liệu Khoa Học Kỹ Thuật: http://tailieukythuat.info
Thiết bị Điện Công Nghiệp - Điện Hạ Thế: http://dienhathe.org
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
Isolation Procedures for Safe Working on Electrical Systems and Equipment by the JIB | solation Procedures for Safe Working on Electrical Systems and Equipment
This chart shows the safe isolation procedure that you should use when working on electrical systems and equipment.
You'll receive a printed copy of this from your Training Provider, but it's also here as a handy reference to keep electronically.
THE RULES OF SAFE ISOLATION ARE:
Obtain permission to start work (a Permit may be required in some situations)
Identify the source(s) of supply using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Isolate the supply(s)
Secure the isolation
Prove the system/equipment is DEAD using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Put up warning signs to tell other people that the electrical installation has been isolated
Once the system/equipment is proved DEAD, work can begin
Uploaded by THORNE & DERRICK LV HV Jointing, Earthing, Substation & Electrical Eqpt | Explosive Atmosphere Experts & ATEX IECEx.
THORNE & DERRICK based in the UK are international distributors of LV, MV & HV Cable Installation, Jointing, Substation & Electrical Equipment.
Since 1985, T&D have established an international reputation based on SERVICE | INTEGRITY | TRUST.
Contact us for 3M, ABB, Alroc, AN Wallis, CATU, Cembre, Centriforce, CMP, CSD, Elastimold, Ellis Patents, Emtelle, Euromold, Filoform , Furse, Lucy Electric & Zodion, Nexans, Pfisterer, Polypipe, Prysmian, Roxtec, Sicame, WT Henley.
Smart TV Buyer Insights Survey 2024 by 91mobiles.pdf91mobiles
91mobiles recently conducted a Smart TV Buyer Insights Survey in which we asked over 3,000 respondents about the TV they own, aspects they look at on a new TV, and their TV buying preferences.
GraphRAG is All You need? LLM & Knowledge GraphGuy Korland
Guy Korland, CEO and Co-founder of FalkorDB, will review two articles on the integration of language models with knowledge graphs.
1. Unifying Large Language Models and Knowledge Graphs: A Roadmap.
https://arxiv.org/abs/2306.08302
2. Microsoft Research's GraphRAG paper and a review paper on various uses of knowledge graphs:
https://www.microsoft.com/en-us/research/blog/graphrag-unlocking-llm-discovery-on-narrative-private-data/
Le nuove frontiere dell'AI nell'RPA con UiPath Autopilot™UiPathCommunity
In questo evento online gratuito, organizzato dalla Community Italiana di UiPath, potrai esplorare le nuove funzionalità di Autopilot, il tool che integra l'Intelligenza Artificiale nei processi di sviluppo e utilizzo delle Automazioni.
📕 Vedremo insieme alcuni esempi dell'utilizzo di Autopilot in diversi tool della Suite UiPath:
Autopilot per Studio Web
Autopilot per Studio
Autopilot per Apps
Clipboard AI
GenAI applicata alla Document Understanding
👨🏫👨💻 Speakers:
Stefano Negro, UiPath MVPx3, RPA Tech Lead @ BSP Consultant
Flavio Martinelli, UiPath MVP 2023, Technical Account Manager @UiPath
Andrei Tasca, RPA Solutions Team Lead @NTT Data
DevOps and Testing slides at DASA ConnectKari Kakkonen
My and Rik Marselis slides at 30.5.2024 DASA Connect conference. We discuss about what is testing, then what is agile testing and finally what is Testing in DevOps. Finally we had lovely workshop with the participants trying to find out different ways to think about quality and testing in different parts of the DevOps infinity loop.
Epistemic Interaction - tuning interfaces to provide information for AI supportAlan Dix
Paper presented at SYNERGY workshop at AVI 2024, Genoa, Italy. 3rd June 2024
https://alandix.com/academic/papers/synergy2024-epistemic/
As machine learning integrates deeper into human-computer interactions, the concept of epistemic interaction emerges, aiming to refine these interactions to enhance system adaptability. This approach encourages minor, intentional adjustments in user behaviour to enrich the data available for system learning. This paper introduces epistemic interaction within the context of human-system communication, illustrating how deliberate interaction design can improve system understanding and adaptation. Through concrete examples, we demonstrate the potential of epistemic interaction to significantly advance human-computer interaction by leveraging intuitive human communication strategies to inform system design and functionality, offering a novel pathway for enriching user-system engagements.
Encryption in Microsoft 365 - ExpertsLive Netherlands 2024Albert Hoitingh
In this session I delve into the encryption technology used in Microsoft 365 and Microsoft Purview. Including the concepts of Customer Key and Double Key Encryption.
Climate Impact of Software Testing at Nordic Testing DaysKari Kakkonen
My slides at Nordic Testing Days 6.6.2024
Climate impact / sustainability of software testing discussed on the talk. ICT and testing must carry their part of global responsibility to help with the climat warming. We can minimize the carbon footprint but we can also have a carbon handprint, a positive impact on the climate. Quality characteristics can be added with sustainability, and then measured continuously. Test environments can be used less, and in smaller scale and on demand. Test techniques can be used in optimizing or minimizing number of tests. Test automation can be used to speed up testing.
Removing Uninteresting Bytes in Software FuzzingAftab Hussain
Imagine a world where software fuzzing, the process of mutating bytes in test seeds to uncover hidden and erroneous program behaviors, becomes faster and more effective. A lot depends on the initial seeds, which can significantly dictate the trajectory of a fuzzing campaign, particularly in terms of how long it takes to uncover interesting behaviour in your code. We introduce DIAR, a technique designed to speedup fuzzing campaigns by pinpointing and eliminating those uninteresting bytes in the seeds. Picture this: instead of wasting valuable resources on meaningless mutations in large, bloated seeds, DIAR removes the unnecessary bytes, streamlining the entire process.
In this work, we equipped AFL, a popular fuzzer, with DIAR and examined two critical Linux libraries -- Libxml's xmllint, a tool for parsing xml documents, and Binutil's readelf, an essential debugging and security analysis command-line tool used to display detailed information about ELF (Executable and Linkable Format). Our preliminary results show that AFL+DIAR does not only discover new paths more quickly but also achieves higher coverage overall. This work thus showcases how starting with lean and optimized seeds can lead to faster, more comprehensive fuzzing campaigns -- and DIAR helps you find such seeds.
- These are slides of the talk given at IEEE International Conference on Software Testing Verification and Validation Workshop, ICSTW 2022.
LF Energy Webinar: Electrical Grid Modelling and Simulation Through PowSyBl -...DanBrown980551
Do you want to learn how to model and simulate an electrical network from scratch in under an hour?
Then welcome to this PowSyBl workshop, hosted by Rte, the French Transmission System Operator (TSO)!
During the webinar, you will discover the PowSyBl ecosystem as well as handle and study an electrical network through an interactive Python notebook.
PowSyBl is an open source project hosted by LF Energy, which offers a comprehensive set of features for electrical grid modelling and simulation. Among other advanced features, PowSyBl provides:
- A fully editable and extendable library for grid component modelling;
- Visualization tools to display your network;
- Grid simulation tools, such as power flows, security analyses (with or without remedial actions) and sensitivity analyses;
The framework is mostly written in Java, with a Python binding so that Python developers can access PowSyBl functionalities as well.
What you will learn during the webinar:
- For beginners: discover PowSyBl's functionalities through a quick general presentation and the notebook, without needing any expert coding skills;
- For advanced developers: master the skills to efficiently apply PowSyBl functionalities to your real-world scenarios.
Observability Concepts EVERY Developer Should Know -- DeveloperWeek Europe.pdfPaige Cruz
Monitoring and observability aren’t traditionally found in software curriculums and many of us cobble this knowledge together from whatever vendor or ecosystem we were first introduced to and whatever is a part of your current company’s observability stack.
While the dev and ops silo continues to crumble….many organizations still relegate monitoring & observability as the purview of ops, infra and SRE teams. This is a mistake - achieving a highly observable system requires collaboration up and down the stack.
I, a former op, would like to extend an invitation to all application developers to join the observability party will share these foundational concepts to build on:
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...SOFTTECHHUB
The choice of an operating system plays a pivotal role in shaping our computing experience. For decades, Microsoft's Windows has dominated the market, offering a familiar and widely adopted platform for personal and professional use. However, as technological advancements continue to push the boundaries of innovation, alternative operating systems have emerged, challenging the status quo and offering users a fresh perspective on computing.
One such alternative that has garnered significant attention and acclaim is Nitrux Linux 3.5.0, a sleek, powerful, and user-friendly Linux distribution that promises to redefine the way we interact with our devices. With its focus on performance, security, and customization, Nitrux Linux presents a compelling case for those seeking to break free from the constraints of proprietary software and embrace the freedom and flexibility of open-source computing.
UiPath Test Automation using UiPath Test Suite series, part 4DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 4. In this session, we will cover Test Manager overview along with SAP heatmap.
The UiPath Test Manager overview with SAP heatmap webinar offers a concise yet comprehensive exploration of the role of a Test Manager within SAP environments, coupled with the utilization of heatmaps for effective testing strategies.
Participants will gain insights into the responsibilities, challenges, and best practices associated with test management in SAP projects. Additionally, the webinar delves into the significance of heatmaps as a visual aid for identifying testing priorities, areas of risk, and resource allocation within SAP landscapes. Through this session, attendees can expect to enhance their understanding of test management principles while learning practical approaches to optimize testing processes in SAP environments using heatmap visualization techniques
What will you get from this session?
1. Insights into SAP testing best practices
2. Heatmap utilization for testing
3. Optimization of testing processes
4. Demo
Topics covered:
Execution from the test manager
Orchestrator execution result
Defect reporting
SAP heatmap example with demo
Speaker:
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
Transcript: Selling digital books in 2024: Insights from industry leaders - T...BookNet Canada
The publishing industry has been selling digital audiobooks and ebooks for over a decade and has found its groove. What’s changed? What has stayed the same? Where do we go from here? Join a group of leading sales peers from across the industry for a conversation about the lessons learned since the popularization of digital books, best practices, digital book supply chain management, and more.
Link to video recording: https://bnctechforum.ca/sessions/selling-digital-books-in-2024-insights-from-industry-leaders/
Presented by BookNet Canada on May 28, 2024, with support from the Department of Canadian Heritage.
The Art of the Pitch: WordPress Relationships and SalesLaura Byrne
Clients don’t know what they don’t know. What web solutions are right for them? How does WordPress come into the picture? How do you make sure you understand scope and timeline? What do you do if sometime changes?
All these questions and more will be explored as we talk about matching clients’ needs with what your agency offers without pulling teeth or pulling your hair out. Practical tips, and strategies for successful relationship building that leads to closing the deal.
A tale of scale & speed: How the US Navy is enabling software delivery from l...sonjaschweigert1
Rapid and secure feature delivery is a goal across every application team and every branch of the DoD. The Navy’s DevSecOps platform, Party Barge, has achieved:
- Reduction in onboarding time from 5 weeks to 1 day
- Improved developer experience and productivity through actionable findings and reduction of false positives
- Maintenance of superior security standards and inherent policy enforcement with Authorization to Operate (ATO)
Development teams can ship efficiently and ensure applications are cyber ready for Navy Authorizing Officials (AOs). In this webinar, Sigma Defense and Anchore will give attendees a look behind the scenes and demo secure pipeline automation and security artifacts that speed up application ATO and time to production.
We will cover:
- How to remove silos in DevSecOps
- How to build efficient development pipeline roles and component templates
- How to deliver security artifacts that matter for ATO’s (SBOMs, vulnerability reports, and policy evidence)
- How to streamline operations with automated policy checks on container images
1. T e c h n i c a l D a t a S h e e t
London Underground Station Upgrade - 40A Die-cast Isolators
Craig & Derricott Ltd
Hall Lane, Walsall Wood,
Walsall, West Midlands WS9 9DP
t: +44(0)1543 375541 f: +44(0)1543 361619
e: sales@craigandderricott.com
craigandderricott.com
page 1
40A Switch Disconnectors
Die-cast Enclosures Finished in Dark Admiralty Grey
The die-cast range of switch disconnectors from Craig &
Derricott provides the ultimate in strength and flexibility for
today's industrial installations.
Available in both 25A and 40A ratings, the options available
will cover the majority of applications found in a typical site
project.
Years of being at the forefront of switch disconnector
manufacture has enabled us to provide the very best in
quality and reliability.
• Ratings to BS EN 60947-3
Ithe 40A, AC23A : 15.0kW at 415V.
• Base mounting switch interiors.
• Standard items available in 2, 3, 4 and 6 poles.
3 and 6 pole options with 2 early break (E/B)
auxiliaries.
• Neutral links form part of the switch interior.
• 2 x M20 tapped cable entries (1 off plugged)
• Enclosure material - Aluminium (LM6).
• Sealing to IP65.
• Paint finish:-
Copon 35TR or 38TR system
Colour - Dark Admiralty Grey* BS 381C 632HG
• Supplied with pre-finished steel mounting brackets.
• Captive lid fixing screws with security head.
• Padlocking cast lever.
• Positive break contacts.
• A maximum of 8 contacts available in the 40A size.
(Additional with cast extensions to increase depth)
• Earthing points on both lid and enclosure base plus
external M10 earth terminal.
• Padlocking in both ‘On’ & ‘Off’ positions
• Labels - Engraved traffolyte labels in various
colours can be mounted on the enclosure lid, or
supplied loose for mounting adjacent to the isolator.
• Second product label supplied loose for fitting by
contractor where original label may be obscured.
Features:-
Configuration Catalogue Number
2 Pole DCG402LUL10
3 Pole DCG403LUL10
3 Pole + 2 E/B Aux. DCG403EBLUL10
4 Pole DCG404LUL10
6 Pole DCG406LUL10
6 Pole + 2 E/B Aux. DCG406EBLUL10
Ordering Information:-
To order a neutral link please include in ref as follows:-
Example 3 pole + Neutral Link
DCG403NLLUL10
*To order the enclosurefinished RED, please replace
the Gw ith R eg:- DCR406LUL10
Spares
To order spare switch interiors, add suffix
/INT to the part number as follows:-
Example 3 pole
RTB4021/HPD10/GY/LUL/INT
Set of 4 off security lid fixing screws
Order code R40/SEC/FIX
Security screwdriver bit
Order code R40/SEC/SCREWBIT
Touch-up paint
Order code COPON/LUL/DAGRY
Dimensions:-
Termination - M4
Maximum Cable Size - 6 mm2
External Fixings - M6
Weight - Approx. 2.5kg
Overall Depth - 140
WWW.CABLEJOINTS.CO.UK
THORNE & DERRICK UK
TEL 0044 191 490 1547 FAX 0044 477 5371
TEL 0044 117 977 4647 FAX 0044 977 5582
WWW.THORNEANDDERRICK.CO.UK