This summary provides the key details about an experiment conducted to test the effectiveness of an exoskeleton device.
1) The experiment tested an exoskeleton device, called a personal ergonomic device (PED), on welders and painters at a manufacturing facility to see if it reduced fatigue and increased productivity.
2) The experiment aimed to test the hypothesis that using the exoskeleton device would increase productivity and quality of tasks by reducing operator fatigue and soreness.
3) The results of the experiment and effectiveness of the exoskeleton device were evaluated based on prior studies that examined fatigue in welders' muscles from overhead work and tests for measuring functional performance and fatigue in patients
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
reACT Article National Fitness Trade JournalGreg Maurer
Learn how the reACT Trainer improves outcomes for athletes; physical therapy patients; fall prevention and active aging; and healthy gym goers looking for increased strength, power, rapid lower body and core conditioning and toning.
An exoskeleton revolution is set to make the bionic builder a reality. Because construction workers have started packing that kind of kit. In some cases the construction is a bit late for the party - body suits and add-on limbs are already supporting the military, helping to regroup with spinal cord injuries.
Link - http://exoskeleton360.com/index.php/category/exoskeleton-revolution/
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
reACT Article National Fitness Trade JournalGreg Maurer
Learn how the reACT Trainer improves outcomes for athletes; physical therapy patients; fall prevention and active aging; and healthy gym goers looking for increased strength, power, rapid lower body and core conditioning and toning.
An exoskeleton revolution is set to make the bionic builder a reality. Because construction workers have started packing that kind of kit. In some cases the construction is a bit late for the party - body suits and add-on limbs are already supporting the military, helping to regroup with spinal cord injuries.
Link - http://exoskeleton360.com/index.php/category/exoskeleton-revolution/
Intervention of Ergonomics in Hand Driven Cotton Spinning OperationWaqas Tariq
Cotton spinning is an important operation in small scale and cottage textile industries in India. A large number of women workers in these industries perform cotton spinning task adopting squatting posture in traditional workshops.. Forty operators were questioned regarding work related musculoskeletal disorders WMSDs. Among the operators, severe cervical and lumber joint problems along with knee, joint pains and shoulders were more prevalent compared to other body regions. Based on the problems found, a new workstation was developed and ten operators were asked to work in the same workstation. Certain aspects regarding the ergonomic evaluation for those workers are discussed in this study. They were observed and evaluated with the RULA technique and there opinion on the improvement was asked based on the task, most frequent, they performed. It is revealed that the suggested workstation improves working posture and results in reduced postural stress on operators’ bodies and, consequently, reduce prevalence of MSDs symptoms.
Ergonomic Design Principles - Case Study “Computer Laboratory"Esraa Fathy
Project | Applying Ergonomic Design Principles (2012_2013) Under supervision of Dr.Reem ElKadeem.
Project Objective:
The goal of the project is to exercise the application of ergonomic design principles combined with our creative talent in solving or preventing current problems in real case study. Sometimes minor ergonomic changes in the design of equipment, workstations or job tasks can make significant improvements in worker’s comfort, health, safety and productivity.
Our team was required to select one of workstations in the college and make a comparison between two workstations of the same category. Our case study was about “Computer Laboratory” (Production Workshop / Mechanical Building).
Project Deliverables:
Our team was required to document both the activities performed throughout the project and the application of the mechanism in industry in the form of a Technical Report. The report contains: Workstation Description _Workstation Assessment: through observation and NIOSH & OSHA surveys. _Workstation Measurements:Measuring of necessary workstation dimensions. _ Workstation Analysis: Identifying of risk factors causing WMSD, suggesting of modifications.
Results and conclusion: Criticizing both workstations and showing result of comparison.
And to present the activities performed throughout the project in the form of a PowerPoint Presentation.
Few things can have a worse impact on the efficiency and profitability of a business than poor worker safety. While much employer focus on the common factors like retention making sure that your workers are comfortable and happy by providing proper standing surfaces and safety concerns.
Background
Traditionally, metallic interference screws were considered to have increased resistance to load than bio absorbable screws in anterior cruciate ligament (ACL) reconstruction. We did a comparative evaluation of biodegradable and metallic interference screws for tibial sided ACL reconstruction and also analysed complications, compared clinical outcome, did imaging study of ACL single bundle reconstruction by using titanium & newer poly–L-lactic acid (PLLA) bio absorbable screws to determine as to whether bio absorbable screw which costs double the metallic screw, is functionally better than standard metallic screws.
Methods
This is a prospective comparative study conducted among 50 patients aged between 15 and 55 years with clinical and MRI confirmation of complete ACL tear, treated arthroscopically with ACL reconstruction with either bio absorbable (group 1) or metallic (group 2) interference screw and both the groups were compared on follow up for an average duration of 12 months. Lysholm and Gillquist Knee Scoring Scale were used and outcome scores were divided into excellent, good, fair and poor.
Results
In our study 41 patients were males and 9 were females. Bio screw was used in 24 males and 6 female patients. Metallic screw was used in 17 males and 3 females. Outcome score was excellent in 26 (52 %) cases, good in 18 (36 %) cases, fair in 4 (8 %) cases, poor in 2 (4 %) cases. The mean Lysholm score in bio absorbable group was 93.13 and in metallic group was 89.70. Knee effusion was higher in bio screw group and infection rate was higher in metallic group.
Conclusions
In our study, the difference between bio absorbable screw group and metallic screw group was insignificant with regard to final patient outcome. Final osseointegration was better with bio absorbable screw, but increased cost of implant and almost same results compared to metallic screw does not make the bio absorbable screw superior to its counterpart.
General Formula for Optimum Location of Chip Breaker in Tool Inserts for Indu...YogeshIJTSRD
Metal cutting process depends on chip generation for its effectiveness. It is a measurable quantity which largely depends on the nature of chips generated and its effect on the tool performance. This paper shall consider occupational health and safety to address the concept of chip breakers used in machining of ductile materials. The mechanics of metal cutting shall be the basis for the said derivation with the premise being that of fracture on account of a combined state of bending and shear stresses during the chip propagation. This can be effective to design tool inserts with optima in perspective so that the end users being machine operators are ensured with a safe working zone without the presence of long continuous chips that can cause hazards like bodily injury or severing of delicate organs thereby meeting the international standard requirements. Towards the end, various health and safety aspects shall be summarized and a conclusion shall be drawn accordingly. Gourav Vivek Kulkarni | Ajay Parulkar "General Formula for Optimum Location of Chip Breaker in Tool Inserts for Industrial Safety" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-3 , April 2021, URL: https://www.ijtsrd.com/papers/ijtsrd39814.pdf Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/39814/general-formula-for-optimum-location-of-chip-breaker-in-tool-inserts-for-industrial-safety/gourav-vivek-kulkarni
Graphite may prevent complications caused by the devicedepuysettlements
Among the symptoms of flawed hip devices are pain on the hip area, pain on the thigh or groin area, pain while walking, pain when rising from a seated position, pain bearing weight and swelling.
Legal observers say that the DePuy hip replacement lawsuit should be a learning example to other manufacturing companies to ensure safety of their products. For more inputs just visit here at this webiste: www.depuysettlements.com
There is a higher potentiality for hip implant failure, causing more health complications, in women than in men, revealed by one of the largest hip replacement study in the US. The Stryker Hip Replacement Lawsuit Center helps you learn more about hip replacements and its potential side effects.
OrthoXel Apex Tibial Nailing System SummaryAlanna Carty
Overview of new orthopaedic trauma intramedullary nailing sytem with unique micromotion locking from OrthoXel an innovative new company in the orthopaedic space. Visit www.orthoxel.net for more information or to contact us.
Ergonomic furniture is a contented substitute to your normal office furniture. Ergonomic office furniture is a great investment in your work and the health of you and your employees. Here are some benefits of Ergonomic Office Furniture… These will help you to organize your office in better way.
The interface pressure between foot plantar surface and shoe soles is an important parameter frequently measured during gait analysis. This foot pressure measurement has wide applications, for example screening for high-risk diabetic foot ulceration, the design of orthotics for diabetes mellitus and peripheral neuropathy, footwear design improvement of
balance, sports injury prevention in athletes plus much more. It is, therefore, crucial to devise techniques to accurately and efficiently measure this type of foot pressure.
In-shoe foot plantar sensors have paved the way to better efficiency, flexibility, mobility and reduced cost measurement systems. For the system to be mobile and wearable for monitoring activities of daily life, the system should be wireless with low power consumption.
Intervention of Ergonomics in Hand Driven Cotton Spinning OperationWaqas Tariq
Cotton spinning is an important operation in small scale and cottage textile industries in India. A large number of women workers in these industries perform cotton spinning task adopting squatting posture in traditional workshops.. Forty operators were questioned regarding work related musculoskeletal disorders WMSDs. Among the operators, severe cervical and lumber joint problems along with knee, joint pains and shoulders were more prevalent compared to other body regions. Based on the problems found, a new workstation was developed and ten operators were asked to work in the same workstation. Certain aspects regarding the ergonomic evaluation for those workers are discussed in this study. They were observed and evaluated with the RULA technique and there opinion on the improvement was asked based on the task, most frequent, they performed. It is revealed that the suggested workstation improves working posture and results in reduced postural stress on operators’ bodies and, consequently, reduce prevalence of MSDs symptoms.
Ergonomic Design Principles - Case Study “Computer Laboratory"Esraa Fathy
Project | Applying Ergonomic Design Principles (2012_2013) Under supervision of Dr.Reem ElKadeem.
Project Objective:
The goal of the project is to exercise the application of ergonomic design principles combined with our creative talent in solving or preventing current problems in real case study. Sometimes minor ergonomic changes in the design of equipment, workstations or job tasks can make significant improvements in worker’s comfort, health, safety and productivity.
Our team was required to select one of workstations in the college and make a comparison between two workstations of the same category. Our case study was about “Computer Laboratory” (Production Workshop / Mechanical Building).
Project Deliverables:
Our team was required to document both the activities performed throughout the project and the application of the mechanism in industry in the form of a Technical Report. The report contains: Workstation Description _Workstation Assessment: through observation and NIOSH & OSHA surveys. _Workstation Measurements:Measuring of necessary workstation dimensions. _ Workstation Analysis: Identifying of risk factors causing WMSD, suggesting of modifications.
Results and conclusion: Criticizing both workstations and showing result of comparison.
And to present the activities performed throughout the project in the form of a PowerPoint Presentation.
Few things can have a worse impact on the efficiency and profitability of a business than poor worker safety. While much employer focus on the common factors like retention making sure that your workers are comfortable and happy by providing proper standing surfaces and safety concerns.
Background
Traditionally, metallic interference screws were considered to have increased resistance to load than bio absorbable screws in anterior cruciate ligament (ACL) reconstruction. We did a comparative evaluation of biodegradable and metallic interference screws for tibial sided ACL reconstruction and also analysed complications, compared clinical outcome, did imaging study of ACL single bundle reconstruction by using titanium & newer poly–L-lactic acid (PLLA) bio absorbable screws to determine as to whether bio absorbable screw which costs double the metallic screw, is functionally better than standard metallic screws.
Methods
This is a prospective comparative study conducted among 50 patients aged between 15 and 55 years with clinical and MRI confirmation of complete ACL tear, treated arthroscopically with ACL reconstruction with either bio absorbable (group 1) or metallic (group 2) interference screw and both the groups were compared on follow up for an average duration of 12 months. Lysholm and Gillquist Knee Scoring Scale were used and outcome scores were divided into excellent, good, fair and poor.
Results
In our study 41 patients were males and 9 were females. Bio screw was used in 24 males and 6 female patients. Metallic screw was used in 17 males and 3 females. Outcome score was excellent in 26 (52 %) cases, good in 18 (36 %) cases, fair in 4 (8 %) cases, poor in 2 (4 %) cases. The mean Lysholm score in bio absorbable group was 93.13 and in metallic group was 89.70. Knee effusion was higher in bio screw group and infection rate was higher in metallic group.
Conclusions
In our study, the difference between bio absorbable screw group and metallic screw group was insignificant with regard to final patient outcome. Final osseointegration was better with bio absorbable screw, but increased cost of implant and almost same results compared to metallic screw does not make the bio absorbable screw superior to its counterpart.
General Formula for Optimum Location of Chip Breaker in Tool Inserts for Indu...YogeshIJTSRD
Metal cutting process depends on chip generation for its effectiveness. It is a measurable quantity which largely depends on the nature of chips generated and its effect on the tool performance. This paper shall consider occupational health and safety to address the concept of chip breakers used in machining of ductile materials. The mechanics of metal cutting shall be the basis for the said derivation with the premise being that of fracture on account of a combined state of bending and shear stresses during the chip propagation. This can be effective to design tool inserts with optima in perspective so that the end users being machine operators are ensured with a safe working zone without the presence of long continuous chips that can cause hazards like bodily injury or severing of delicate organs thereby meeting the international standard requirements. Towards the end, various health and safety aspects shall be summarized and a conclusion shall be drawn accordingly. Gourav Vivek Kulkarni | Ajay Parulkar "General Formula for Optimum Location of Chip Breaker in Tool Inserts for Industrial Safety" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-5 | Issue-3 , April 2021, URL: https://www.ijtsrd.com/papers/ijtsrd39814.pdf Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/39814/general-formula-for-optimum-location-of-chip-breaker-in-tool-inserts-for-industrial-safety/gourav-vivek-kulkarni
Graphite may prevent complications caused by the devicedepuysettlements
Among the symptoms of flawed hip devices are pain on the hip area, pain on the thigh or groin area, pain while walking, pain when rising from a seated position, pain bearing weight and swelling.
Legal observers say that the DePuy hip replacement lawsuit should be a learning example to other manufacturing companies to ensure safety of their products. For more inputs just visit here at this webiste: www.depuysettlements.com
There is a higher potentiality for hip implant failure, causing more health complications, in women than in men, revealed by one of the largest hip replacement study in the US. The Stryker Hip Replacement Lawsuit Center helps you learn more about hip replacements and its potential side effects.
OrthoXel Apex Tibial Nailing System SummaryAlanna Carty
Overview of new orthopaedic trauma intramedullary nailing sytem with unique micromotion locking from OrthoXel an innovative new company in the orthopaedic space. Visit www.orthoxel.net for more information or to contact us.
Ergonomic furniture is a contented substitute to your normal office furniture. Ergonomic office furniture is a great investment in your work and the health of you and your employees. Here are some benefits of Ergonomic Office Furniture… These will help you to organize your office in better way.
The interface pressure between foot plantar surface and shoe soles is an important parameter frequently measured during gait analysis. This foot pressure measurement has wide applications, for example screening for high-risk diabetic foot ulceration, the design of orthotics for diabetes mellitus and peripheral neuropathy, footwear design improvement of
balance, sports injury prevention in athletes plus much more. It is, therefore, crucial to devise techniques to accurately and efficiently measure this type of foot pressure.
In-shoe foot plantar sensors have paved the way to better efficiency, flexibility, mobility and reduced cost measurement systems. For the system to be mobile and wearable for monitoring activities of daily life, the system should be wireless with low power consumption.
Để xem full tài liệu Xin vui long liên hệ page để được hỗ trợ
:
https://www.facebook.com/garmentspace/
https://www.facebook.com/thuvienluanvan01
HOẶC
https://www.facebook.com/thuvienluanvan01
https://www.facebook.com/thuvienluanvan01
tai lieu tong hop, thu vien luan van, luan van tong hop, do an chuyen nganh
Aula realizada no Centro Espírita
Kardecian Spiritist Society of Florida
Ciclo I - Conhecendo o Espiritismo - Aula 6
Data: Maio 2014
Web: www.kardecian.org
Facebook: KSSF Kardecian Spiritist Society of Florida
This paper of finite element analysis of the rib cage model is applied to recognize stress distributions and to determine the rate of bone fractures(especially for pathologically changed bones). Also to determine the load and stress to occurs on the human rib cage at any accident. Also find the maximum load sustain capacity of human rib cage and according to the load sustain capacity of the human rib cage by finite element analysis and search a material as like a bone cement and it take on a rib fracture and see the result . This paper is only of to nullify the rib fracture as present medical treatment give the elastic belt but due to respiration, the human ribs are contract and relax that’s the rib fracture are only minimize not a nullify. The human models are considered in between age 15 to 40 year. The Simulation result shows a good agreement with the cadaver test data.
A study on push pull analysis associated with awkward posture among workers i...eSAT Journals
Abstract In aerospace industries, many working tasks required their workers to perform works in push-pull activity. It is associated with an awkward posture. The awkward posture is a practical working posture when joints are not in neutral position. Furthermore, the workers need to push or pull the mould in a long distance into a workplace. If the workers perform the activity continuously throughout the working hours, they may be experienced back pain problem. The objective of this study is to measure the maximum acceptable initial force and sustained force for push-pull activity while workers perform their tasks. Besides that, this study also wants to identify which activity can endure longer between push or pull activity. Moreover, this study measures the comfort level of working posture. The acceptable initial force and sustained force were measured using Push-Pull Analysis, expressed in Newton, N. The comfort level is measured using Rapid Upper Limb Assessment (RULA) Analysis, expressed in scoring level. Both of these assessments are analysis tools Computer-Aided Three-Dimensional Interactive Application (CATIA) software. Six production workers from manufacturing department were participated as subjects. The results show the maximum acceptable initial force for push task is 433.942N and pull task is 396.691N. While, the sustained force for push task is 333.465N and pull task is 318.317N. Referring to the results, pushing activity can endure longer than pulling activity while workers perform their tasks. While the comfort level for this working posture is seven. Based on this study, the authors concluded that push-pull activity can lead to the back pain problem for workers in aerospace industry. It’s was influenced by the work activity, work load, work duration of awkward posture and distance between workplace. Keywords:Push-pull activity, awkward posture, Acceptable initial force, Acceptable sustained force, Comfort level
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
“Multi-Purpose Manually Operated Cart” is a cart which is designed ergonomically to improve the working conditions of laborers and workers at
construction sites, factories, ports, railway stations, etc. The main objective is to prevent various occupational hazards and improve the quality of life for
workers everywhere. The simple, durable, light weight and cost effective carrier is intended to reduce the pressure put on the spine when load is carried
on the head. There is also a good hand grip which reduces stress on the spine when load is carried on the back or while pushing a cart. In due course of
our study we analyzed working condition of laborers and people living around our city, usually they carry goods or materials on their head, back,
shoulders which make the task more difficult for them and they are more prone to injuries thereby aroused the need of an ergonomic push cart which
would help them to carry materials easy and without injuries. The easily usable carrier, made up of cane which underwent bending process for giving it a
designed shape. This cane structure weighs 1 kg which is provided with cushions and belt. The main objective of the design is to prevent various
occupational hazards and improve the quality of life of the laborer. This product will help them in their work. The carrier can be used into three different
forms. This allows the user to carry lighter loads on the head, medium loads at the back and heavier loads on a trolley. Ergonomically the load is
distributed on the shoulder and at the lumber support by softer material.
Basic Hazard AwarenessThis material was produced under the gr.docxjasoninnes20
Basic Hazard Awareness
“This material was produced under the grant SH-20839-SHO from the Occupational Safety and Health Administration, U.S. Department of Labor. It does not necessarily reflect the views or policies of the U.S. Department of Labor, nor does mention of trade names, commercial products, or organizations imply endorsement by the U.S. Government.”
Objectives
By the end of this workshop, you will:
Identify how workplace injuries or illnesses can affect your everyday life.
Identify common symptoms, aches/pains, illnesses and injuries that are associated with your work.
Identify and recognize the exposures and hazards linked to work-related illnesses and injuries.
Develop solutions and strategies to address these identified hazards.
CHEMICAL & DUST HAZARDS
(cleaning products, pesticides, asbestos, etc.)
BIOLOGICAL HAZARDS
(mold, insects/pests, communicable diseases, etc.)
ERGONOMIC HAZARDS
(repetition, lifting, awkward postures, etc.)
WORK ORGANIZATION HAZARDS
Things that cause STRESS!
SAFETY HAZARDS
(slips, trips and falls, faulty equipment, etc.)
PHYSICAL HAZARDS
(noise, temperature extremes, radiation, etc.)
3
Hierarchy of Controls
Requires a physical change to the workplace
Requires worker to wear something
Elimination/Substitution
Requires worker or employer to do something
Most Effective
Least Effective
These are referred to as the hierarchy of controls, how you prevent or control a hazard:
Elimination/Substitution: The main goal for any fix to a hazard or exposure is to eliminate it altogether or substitute a product or method of doing the work to a less hazardous alternative. (e.g. green cleaning products)
4
CONTROLS: Engineering
CONTROL AT THE SOURCE!
Limits the hazard but doesn’t entirely remove it.
Local Exhaust
Other Examples:
Mechanical Guards
Wet Methods for Dust
Enclosures/Isolation
Dilution Ventilation
Proper equipment
Re-designed Tools
Image: by Kare_Products
Image: by JohnRH4's photostream
Image: by purpleslog’s photostream
5
The basic concept behind engineering controls is that, to the extent feasible, the work environment and the job itself should be designed to eliminate hazards or reduce exposure to hazards. While this approach is called engineering controls, it does not necessarily mean that an engineer is required to design the control. Engineering controls are the "first line of defense" against injury/illness, because they have the potential to completely eliminate a hazard, and do not rely on human behavior to be effective. For instance, rather than require employees to wear respiratory protection which must be monitored, inspected, trained, managed, it's much more effective to install a ventilation system that does not require any of those management activities or, better yet, find an alternative substitute that is less hazardous.
Images from: Creative Commons:
You are free:
to Share — to copy, distribute and transmit the work
to Remix — to adapt the work
Under t ...
Design Requirements For a Tendon Rehabilitation Robot: Results From a Survey ...ertekg
Download Link > https://ertekprojects.com/gurdal-ertek-publications/blog/design-requirements-for-a-tendon-rehabilitation-robot-results-from-a-survey-of-engineers-and-health-professionals/
Exoskeleton type finger rehabilitation robots are helpful in assisting the treatment of tendon injuries. A survey has been carried out with engineers and health professionals to further develop an existing finger exoskeleton prototype. The goal of the study is to better understand the relative importance of several design criteria through the analysis of survey results and to improve the finger exoskeleton accordingly. The survey questions with strong correlations are identified and the preferences of the two respondent groups are statistically compared. The results of the statistical analysis are interpreted and insights obtained are used to guide the design process. The answers to the qualitative questions are also discussed together with their design implications. Finally, Quality Function Deployment (QFD) has been employed for visualizing these functional requirements in relation to the customer requirements.
Design Requirements For a Tendon Rehabilitation Robot: Results From a Survey ...
Butler_0916
1. 32 ProfessionalSafety september 2016 www.asse.org
Ergonomics
Peer-Reviewed
Terry R. Butler, CSP, is president of Lean Steps Consulting Inc. He has previ-
ously worked in global manufacturing for Archer Daniel Midlands and Sheaffer
Pen Co., and most recently vice president of facilities and EH&S for Vermeer
Corp. in Pella, IA. Butler holds B.S. degrees in Occupational Safety Engineering
and Industrial Technology from Illinois State University. He is a past member
of the Iowa Emergency Response Commission and Safeguard Partnership, and
currently serves on the Governor’s Iowa Occupational Safety and Health Advisory
Council board and Safe Water International Ministries board. He is a professional
member of ASSE’s Hawkeye Chapter.
IN BRIEF
•This article discusses the use of
exoskeleton technology to ergonomi-
cally reduce shoulder overexertion
in employees who extend and raise
their arms.
•It presents some potential benefits
and safety challenges of using such
technology to simultaneously protect
workers and increase productivity.
•The benefits presented are quantified
from real-life field testing conducted
at a large manufacturing facility and
should help the reader understand the
level of testing and research neces-
sary to properly evaluate an exoskel-
eton technology before introducing it
into a workplace.
E
xoskeleton technology comes in many
forms, some of which can be powered by bat-
teries and some with the use of stored energy
within mechanical components. This article focuses
on the latter, as its application is more universal and
affordable for a broader range
of industries. The exoskeleton
technology discussed in this
article is a lightweight, strictly
mechanical device that will er-
gonomically reduce shoulder
overexertion in persons who
extend and raise their arms.
This exoskeleton consists
of a frame, armrests and a
system of mechanical compo-
nents that transfer the weight
of the arms from the shoulders
to the core body. The body-
worn exoskeleton moves with
the user while not intruding
into the user’s workspace and
while giving the user full range
of motion, akin to wearing a
backpack around the upper
body. The exoskeleton uses
mechanical arm-support tech-
nology that is inactive until the arms raise. It progres-
sively activates as the arms lift and gradually releases
as the arms return to a resting state.
The device can be configured to a specified
range of motion over which the support mecha-
nism is active, as well as a specified level of sup-
port for the arm. For example, assembly workers
often use tools that weigh as much as 15 lb. These
workers may require the device to support 70% of
arm weight. Alternatively, welders and painters
who typically work with lighter-weight equipment,
such as a weld gun or paint gun, may require the
device to support 50% of arm weight.
In a 2015 article, Panasonic spokesperson Mio
Yamanaka is quoted as saying, “We expect that
exoskeletons, or power-assist suits, will be widely
used in people’s lives in 15 years” (Knight, 2015).
Fifteen years is not long for OSH professionals to
prepare for the deployment of these devices in the
workplace. The physical and psychological effects
of wearing an exoskeleton device are but a few of
the considerations, depending on the device and
its intended application.
Due to exoskeleton technology’s perceived ben-
efits to productivity and quality, pressure may be
placed on safety professionals to allow workers to
wear such devices. As with all forms of PPE, safety
professionals must assess the care, use and limita-
tions of each device introduced to the workplace.
Exoskeletons will vary greatly in complexity as
each will have a specific purpose, so assessing their
limitations will be key to protecting workers who
choose to wear one.
This article presents some potential benefits and
safety challenges of using such technology to si-
multaneously protect workers and increase pro-
ductivity. The benefits presented are quantified
from real-life field testing conducted at a large
manufacturing facility and should help the reader
understand the level of testing and research neces-
sary to properly evaluate an exoskeleton technol-
ogy before introducing it into a workplace.
According to Encyclopedia Britannica for Kids:
Making Workers Safer
and More Productive
By Terry Butler
Exoskeleton
Technology
2. www.asse.org september 2016 ProfessionalSafety 33
An exoskeleton is a hard covering that sup-
ports and protects the bodies of some types of
animals. The word exoskeleton means “outside
skeleton.” Many invertebrates, or animals with-
out backbones, have exoskeletons. Insects are
the largest group of animals that have an exo-
skeleton. (Exoskeleton, 2016)
When researching exoskeleton technology, it
appears inventors are focusing their efforts in three
areas of use: rehabilitation, military applications,
and maneuvering heavy loads or performing re-
petitive motion tasks in various industries.
In the movie Iron Man, the title character invents
and wears an exoskeleton that enables him to fly,
fight villains and ultimately save the world. People
are fascinated with the concept of a suit that can be
worn on the outside of our body to make us super-
human, or if nothing else help us do our jobs and
live life without so much pain from inflamed or
worn out joints.
This article presents the results obtained from
testing an exoskeleton device known as a personal
ergonomic device (PED) with welders and electro-
static painters at Vermeer Corp. in Pella, IA, Aug.
24-28, 2015. Dave Landon, 2015 American Weld-
ing Society president, believes that “exoskeleton
devices can and will be part of our everyday op-
tions for PPE in the coming years as this technol-
ogy is further refined.”
According to Bureau of Labor Statistics (BLS,
2014), the U.S. is seeing an increase of older work-
ers in the active job market. People are not retiring
in their 50s as they did 20 years ago; from 2000 to
2012, the number of people age 45 and older in the
workforce swelled from 34% to 44%. In fact, the 65
and older age group has more than doubled in the
same 12-year period (BLS, 2014).
Aging employees bring to work physical changes
that are not always immediately recognized or ac-
commodated for in the work environment. In fact
as they enter the mid-40s and 50s, workers start
to experience physical and mental changes with
vision, hearing, cognitive ability, mental health,
stress levels and movement control. With age,
these changes often continue to accelerate. Because
of the increase in aging workers, it is no surprise
that sprains and strains continue to lead the trends
of reportable injuries in almost every job sector.
The field test design team intended to prove or
disprove the following hypothesis regarding the
use of an exoskeleton device: “The use of an exo-
skeleton PED increases productivity and quality of
dynamitic (electrostatic painting) and static (MIG
welding) tasks because operator fatigue and asso-
ciated soreness are reduced.”
Field Test Research
In preparation for the field testing, the Herberts
and Kadefors (1976) study of painful shoulders in
welders was evaluated. This study was collaborative
between the departments of otrhopaedic surgery
and clinical nurophysiology at Sahlgren Hospital in
Gothenburg, Sweden. The study is worth reading
in its entirety, as it clearly shows and explains the
physical impact of moderate and severe ergonomic
work positions on the shoulder and its surrounding
tissue over time.
Interesting and applicable to the field test de-
sign team, Herberts and Kadefors’ (1976) study re-
vealed that one of the four rotator cuff muscles (the
supraspinatus muscle) of the upper back that runs
over the shoulder was shown to be consistently
fatigued during moderate and severe ergonomic
stress (overhead) welding. Herberts and Kadefors
(1976) referenced studies that showed “interfer-
ence with the blood supply to the muscle results in
‘localized muscle fatigue.’”
This study was important to the assessment
of exoskeleton device use by welders and paint-
ers because it clearly demonstrates that localized
muscle fatigue occurs with both inexperienced
and experienced welders. Because the study used
both surface electromyography (EMG) electrodes
(Medelec Ltd.) that were applied to pick up EMG
PhotosbyTerryButler
3. 34 ProfessionalSafety september 2016 www.asse.org
signals from the trapezius and deltoid muscles,
and monopolar fine wire (Karma) electrodes were
inserted by means of a tube (cannula) into the su-
praspinatus muscle, the exoskeleton field test team
could gain a complete understanding of fatigue in
welders’ muscles while doing moderate and severe
ergonomic stress type work.
This is particularly important because, should
the use of an exoskeleton device be proven to
minimize welder fatigue, one must understand
why and how. Even with an exoskeleton device, it
is important to prevent fatigue from setting in and
restricting blood flow. In general terms, fatigue is
the decline in the ability of a muscle to generate
force. If an exoskeleton device permits a welder to
work longer but the worker reaches the same level
of fatigue, what has been gained by protecting the
worker? Knowing how fatigue occurs and how
long it takes is important in establishing the use
and limitations of such a device in the workplace.
The team also examined a study by MacDermid,
Ghobrial, Quirion, et al. (2007), that describes the
development of a new test for measuring function-
al performance of the upper extremity and neck,
and assesses reliability and concurrent validity in
patients with shoulder pathology. The relevant
factors of this study to the testing of subjects, with
and without an exoskeleton device, were the test
design and the stopping criteria used to determine
when a patient was fatigued. These details are im-
portant because neither surface EMG monitors nor
monopolar fine wire electrodes were permitted for
use at the test site.
The protocol test criteria from the MacDermid,
et al. (2007), study—the functional impairment
test-head and neck/shoulder/arm (FIT-HaNSA)
protocol—formed the basis for the exoskeleton
test protocol this article’s design team used to
select the severe and moderate ergonomic stress
positions to be used in the exoskeleton test to ac-
celerate fatigue. This test further helped the team
specify the sequencing of tasks so they varied
from moderate to severe and back to moderate
tasks while welding and painting. The goal was
to replicate moving pegs or bottles up and down
on shelves, as well as manipulating nuts and
bolts overhead, as done in the MacDermid, et al.,
study. The ergonomic stress positions used to ac-
celerate fatigue and the stopping criteria of the
MacDermid, et al., study were identified as the
most important elements to use in the field test of
the exoskeleton device.
Field Test Design Overview:
Quality & Productivity Measurements
It was the goal of the field test protocol to en-
sure that the test subjects performed their work in
similar ergonomic stress positions as those found
in the studies cited previously. They were asked
to perform moderate to severe ergonomic tasks
repeatedly until the test subject was fatigued and
there was a decline in the ability of his/her muscles
to generate enough force or control to maintain an
acceptable quality level.
Photos 1 and 2:
Vermeer welders
during testing with
the exoskeleton.
Photo 3 (bottom):
Vermeer painter
during testing with
the exoskeleton.
PhotosbyTerryButler
4. www.asse.org september 2016 ProfessionalSafety 35
Quality and productivity were measured using
state-of-the-art weld and paint simulators that
recorded test performance in real time. The weld
simulator captures quantitative quality and pro-
ductivity data throughout the weld by recording
position, contact tip work distance, work angle,
travel angle and travel speed, and total weld time,
all of which are critical to weld quality.
The weld simulator scored the performance for
each category and provided a total score as well.
Anything less than a cumulative score of 80 pro-
duces an unacceptable weld. The paint simulator
captures quantitative quality and productivity per-
formance data throughout the painting test by re-
cording visual defects such as light pain and runs,
real-time film thickness, transfer efficiency, aver-
age/minimum/maximum film thickness, average/
minimum/maximum dry thickness, and time to
paint each part. Anything below a cumulative score
of 83 produces a part that does not meet finish and
performance quality standards.
Vermeer uses paint and weld simulators daily
when training all welders and painters. For paint-
ing, the team used a 2-D paint simulator designed
by University of Northern Iowa. For welding, the
team used a Lincoln Electric VRTEX 360 3-D weld
simulator. Both simulators allowed the collection
of quantitative quality and productivity data, both
in real time and downloaded to a memory stick
for inclusion in the test analysis. In addition, both
simulators allow the instructor to vary the degree
of difficulty and ergonomic stress by selecting from
a menu of various parts, sizes, shapes and heights.
For the 2-D paint simulator, the painter se-
quenced between five flat parts of varying levels of
height, width, length and difficulty to paint (rect-
angle, key, circle, duck, hood). Each part received
a primer coat and a topcoat. For the 3-D welding
simulator, a 1G V-groove four-pass weld was se-
lected to add duration of the weld time and vary
the angle the welder had to hold the weld gun and
position the body, arm and shoulder while oper-
ating. This weld was performed at two different
height positions. This is an advanced weld that
only experienced welders can perform consistently.
Mark Doyle, founder of Levitate Technolo-
gies, invented the exoskeleton PED used in this
study. According to Doyle, “It was designed to
minimize fatigue and soreness associated with
surgeons performing surgical procedures.” He
continues, “It was designed to help prevent in-
flammation of the muscle, thereby improving
blood flow, reducing fatigue and improving pro-
ductivity and quality.” The ultimate goal, he says,
is “to help prevent injury and discomfort to the
shoulder, neck and back.”
Field Testing
The exoskeleton field test kicked off Monday,
Aug. 24, 2015. The 5-day field test of the exoskel-
eton device was specifically designed to prove or
disprove whether such a device has a place in a re-
al-world work environment. The field-test design
team started by reviewing the final test protocol
with test subjects. The two most experienced weld-
ers and the two most experienced painters were
selected and fitted with the device. The field-test
team requested the most experienced personnel to
minimize test variables from those less experienced
at welding and painting.
On Monday, each welder and painter was per-
mitted to try out the exoskeleton unit while prac-
ticing on welds and parts to be painted during the
test. On Tuesday, the two welders repeatedly per-
formed the moderate to severe ergonomic stress
weld positions on the weld simulator without the
aid of the exoskeleton device. This established a
baseline for quality and duration prior to reaching
fatigue or their inability to maintain an acceptable
quality level. On Wednesday, the two painters per-
formed moderate to severe ergonomic stress paint-
ing positions repeatedly until they were fatigued or
unable to maintain an acceptable quality level. This
gave the welders a day to recover between testing
with and without the exoskeleton device.
On Thursday, the welders performed the same
test as was conducted on Tuesday, but this time
with the aid of an exoskeleton device. On Friday,
the painters repeated the same test conducted on
Wednesday, but this time with the aid of the exo-
skeleton device.
To measure when fatigue set in and when there
was a noticeable decline in the ability of a muscle
to generate enough force or control to maintain
an acceptable quality level, the team used the fol-
lowing criteria to stop the test. Each welding task
was continued until the quality reached an unac-
ceptable level as noted by the simulator results,
cumulative score of less than 85, but the test could
also be terminated mid-test based on the following
stopping rules:
1) The subject stops or reports that it is too pain-
ful to continue (subjective pain 8 out of 10).
2) The subject is severely off pace and the qual-
ity drops below an 80 overall score as shown by
the computer simulator to the extent that subject is
unable to complete or correct the pace after a brief
pause of less than 10 seconds.
3) The subject substitutes using trunk/whole
body movement and cannot correct with feedback
within 10 seconds while performing the task.
4) The examiner believes the subject is at risk of
injury or other adverse complication if tests were
to continue.
The four stopping rules noted for the welder
were the same for the painter. The only difference
was the simulator used a cumulative score of less
than 83 for more than one test out of each set of 25
painting task repetitions for when to stop the test.
If the painter was unable to complete or correct the
pace after a brief pause of less than 10 seconds, the
test was stopped.
Test Results
The results of the testing performed with-
out, then with an exoskeleton device confirm the
original hypothesis. The painter test subject’s pro-
ductivity was improved with the use of the exoskel-
An added
hypoth-
esized but
unforeseen
benefit
revealed
by the
testing
was relief
of existing
shoulder
discomfort
with the
use of the
exoskele-
ton device.
5. 36 ProfessionalSafety september 2016 www.asse.org
eton PED. One painter’s productivity improved by
26.79% and the other by 53.13% while performing
a dynamitic, moderate to severe ergonomic, repeti-
tive job.
The welder performance without, then with an
exoskeleton device showed that productivity im-
proved 86%. Both welders’ and painters’ quantita-
tive computer data showed quality was maintained
at a higher level for the duration of the painting
and weld tests while wearing an exoskeleton de-
vice. It is believed by the consistency of the qual-
ity scores in both welders and painters that this is
due to improved hand steadiness. Both welders
and painters were able to maintain an acceptable
quality level for a longer period with the aid of the
exoskeleton PED.
An added hypothesized but unforeseen benefit
revealed by the testing was relief of existing shoul-
der discomfort with the use of the exoskeleton de-
vice. This was confirmed with the comments made
by one weld test subject who was still experiencing
shoulder pain after 1 day of rest. At the start of the
second test, the subject reported that his shoulder
felt better after donning the exoskeleton device.
In August 2015, just prior to starting the testing at
the Vermeer site, the same exoskeleton device was
evaluated in a laboratory setting at the University of
San Diego. That test aimed to determine exoskel-
etons’ objective and subjective impact on a group
of volunteers. EMG data were collected by Bradley
Chase (of Chase Consulting) and the university’s
ergonomics lab director. The results were presented
in an unpublished white paper. The results of the
study are illustrated as a percent maximal voluntary
contraction (%MVC). Chase’s test protocol followed
the Vermeer test protocol, which mirrored the Pur-
due Peg Board Task, Minnesota Manual Dexterity
Task, and the MacDermid, et al. (2007), FIT-HaNSA
task protocols.
Chase’s EMG results show the percentage ra-
tio of the applied force to the MVC, for the same
muscle group, in the same posture and expressed
in the same units, to be lower when wearing an
exoskeleton device. The significance of this study
is that it explains why the welders and painters in
this article’s field test were able to weld and paint
longer, and maintain a higher degree of accuracy.
According to Chase, “the EMG data show partici-
pants exhibited a significantly lower %MVC while
wearing the exoskeleton device during physical
tasks compared to the %MVC while not wearing
the device.” Chase continues, “A lower %MVC
implies lower risk for injury due to task demands.”
Further, Chase’s test confirms Herberts and Kade-
fors’ (1976) finding that “the constant traction in
the tendon probably accelerates the degeneration
by circulatory impairment.”
Conclusion
Although the exoskeleton testing proves welders
and painters can perform at a higher quality level
for longer periods (improved productivity) with the
aid of an exoskeleton device, eventually humans
will reach a level of fatigue at which they need to
stop and rest. The perceived benefit is that with
regularly scheduled breaks and lunch, welders and
painters may not reach a level of fatigue that could
be considered dangerous to their safety and health
with the use of an exoskeleton device.
As shown in results of Chase’s EMG study, the use
of an exoskeleton PED helps to prevent fatigue by
slowing muscle contractions that lead to the decline
in a muscle’s ability to generate force. In addition, the
improved productivity and quality as found in this
field test is a potential game-changer for many busi-
nesses whose workforce continues to age.
Add to this the positive effect on the bottom line
by using exoskeleton technology to help newer,
inexperienced workers perform at an acceptable
quality level, faster and more consistently, and Ya-
manaka’s (Knight, 2015) prediction that exoskele-
tons will be widely used in people’s lives in 15 years,
may be the latest we can expect to see exoskeletons
in the workplace. Safety professionals should get
ready as “the exoskeletons are coming.” PS
References
Bureau of Labor Statistics (BLS). (2014, Jan. 6). Labor
force participation projected to fall for people under
age 55 and rise for older age groups. The Economics
Daily. Retrieved from www.bls.gov/opub/ted/2014/
ted_20140106.htm
Chase, B. The Levitate difference: Analysis of the Lev-
itate personal ergonomic device (PED) during various
physical work-related tasks (Unpublished white paper).
San Diego, CA: Levitate Technologies.
Exoskeleton. (2016). In Encyclopedia Britannica Kids.
Retrieved from http://kids.britannica.com/elementary/
article-399448/exoskeleton
Herberts, P. & Kadefors, R. (1976). A study of painful
shoulder in welders. Acta Orthopaedica Scandinavica,
47(4), 381-387. doi:10.3109/17453677608988705
Knight, W. (2015, July 16). The exoskeletons are com-
ing. MIT Technology Review. Retrieved from www
.technologyreview.com/news/539251/the-exoskeletons
-are-coming
MacDermid, J.C., Ghobrial, M., Quirion, K.B., et al.
(2007). Validation of a new test that assesses functional
performance of the upper extremity and neck (FIT-HaNSA)
in patients with shoulder pathology. BMC Musculoskeletal
Disorders, 8(42). doi:10.1186/1471-2474-8-42
Acknowledgments
The Vermeer Corp. test site in Pella, IA, is a
2,500-employee facility that manufactures
industrial and agricultural equipment. The
company employs more than 500 welders,
and operates 16 paint facilities with more
than 50 painters. Special thanks to the com-
pany’s management for giving the field-test
team access to employees, their expertise and
equipment.
For More Information
To learn more about the exoskeleton device
tested in this article, contact Levitate’s Joseph
Zawaideh at josephz@levitatetech.com.