The document summarizes the design and construction of the foundations for the Rion Antirion Bridge in Greece. Key points:
- The foundations had to withstand severe environmental conditions like weak soil, earthquakes, and tectonic movements. An innovative concept was adopted using large diameter caissons resting on reinforced natural ground with steel pipe inclusions.
- Under each caisson, 150-200 steel pipe inclusions 2m in diameter were driven into the soil in a 7m grid to reinforce it. A 2.8m thick gravel layer separated the caisson from the inclusions.
- This concept provided capacity design by allowing sliding at the gravel interface during large seismic forces, limiting forces on the super
The Rion Antirion bridge in Greece connects the Peloponnese peninsula to the mainland across the Gulf of Corinth. Its foundations had to withstand severe environmental conditions including weak soils, earthquakes up to magnitude 7.0, and long-term tectonic movements. The innovative foundation concept adopted reinforced the natural ground with steel tubular piles and included a gravel layer between the piles and foundation raft. This provided capacity to resist the large seismic forces while minimizing differential settlement hazards. Extensive site investigations characterized the poor soil properties to ensure compatible design of seismic demand and foundation capacity.
The document summarizes the design and construction of the foundations for the Rion Antirion Bridge in Greece. An innovative foundation concept was adopted using steel tubular piles driven into the seabed to reinforce the soil, with a gravel layer between the piles and the concrete caisson foundation. This concept provided seismic capacity and minimized differential settlement risks. Close cooperation between designers, contractors, and reviewers was essential to developing and implementing this challenging foundation solution.
The document summarizes the design and construction of the foundations for the Rion Antirion Bridge in Greece. Key points:
1) The foundations used an innovative design of large diameter gravity caissons resting on reinforced natural ground, with steel tubular inclusions and a gravel layer, to address weak soil conditions, seismic activity, and tectonic movements.
2) Subsurface investigations found deep alluvial deposits with low strength and shear wave velocities, posing challenges for the large bridge piers.
3) The foundation concept used capacity design principles, with the gravel layer absorbing inelastic deformations and inclusions providing overstrength to prevent deep failures, allowing sliding if design loads were exceeded.
(2010) - Yates M, Krzeminski M, Berthier D, Hamidi B - The Application of Jet...Michal Krzeminski
Jet grouting was used to construct the Runway End Safety Area for Sydney International Airport. It was needed to bridge over existing structures in a way that stabilized the ground, provided bearing capacity, and created an impermeable barrier. A complex design of jet grout columns with varying diameters, lengths, and reinforcement was implemented based on detailed modeling. Over 1,600 jet grout columns totaling over 13,000 meters in length and 5,100 cubic meters in volume were constructed using a double fluid system to meet the project's geotechnical requirements.
Challenges of Tunneling-- A Peep Into The Exciting World of TunnellingIEI GSC
By Shri Manoj Verman, President, Indian National Group of ISRM
President, International Commission on Hard Rock Excavation
Vice President, Indian Society of Engineering Geology
at 31st National Convention of Civil Engineering
organised by
Gujarat State Center, The Institution of Engineers (India)
at Ahmedabad
1. Careful geological studies are important for selecting dam and reservoir sites to reduce costs and ensure safety and stability.
2. Ideal dam sites have narrow river valleys, competent bedrock like igneous or metamorphic rock near the surface, and favorable geological structures like horizontal or mildly tilted strata.
3. Faults and steeply dipping or folded strata are less desirable as they can compromise the stability and impermeability of the foundation rocks.
1. The document describes the failure of pit slopes at the Deilmann Tailings Management Facility (DTMF) due to collapse of loose outwash sand deposits when resaturated during flooding.
2. Finite element modeling was used to model the stress paths in the sand and ensure stresses did not reach the collapse surface during remediation activities or final flooding. A designed rock buttress was added to prevent triggering of collapse.
3. Geotechnical analyses including limit equilibrium and finite element modeling were used to design slope remediation including flattening slopes and adding a rock buttress to achieve long-term stability with factors of safety over 1.3 and prevent localized collapse triggering.
The document discusses various geological factors that must be considered when constructing tunnels, including: conducting subsurface exploration using pits, adits, drilling, and pilot tunnels; using core drilling and geophysical investigations to interpret geological features; addressing issues related to joint orientation, weathering, faults, rock bursts, and more. Pilot tunnels can help explore critical geological conditions ahead of main excavation and drain rock. The ideal tunnel cross-section depends on the type of rock and purpose of the tunnel.
The Rion Antirion bridge in Greece connects the Peloponnese peninsula to the mainland across the Gulf of Corinth. Its foundations had to withstand severe environmental conditions including weak soils, earthquakes up to magnitude 7.0, and long-term tectonic movements. The innovative foundation concept adopted reinforced the natural ground with steel tubular piles and included a gravel layer between the piles and foundation raft. This provided capacity to resist the large seismic forces while minimizing differential settlement hazards. Extensive site investigations characterized the poor soil properties to ensure compatible design of seismic demand and foundation capacity.
The document summarizes the design and construction of the foundations for the Rion Antirion Bridge in Greece. An innovative foundation concept was adopted using steel tubular piles driven into the seabed to reinforce the soil, with a gravel layer between the piles and the concrete caisson foundation. This concept provided seismic capacity and minimized differential settlement risks. Close cooperation between designers, contractors, and reviewers was essential to developing and implementing this challenging foundation solution.
The document summarizes the design and construction of the foundations for the Rion Antirion Bridge in Greece. Key points:
1) The foundations used an innovative design of large diameter gravity caissons resting on reinforced natural ground, with steel tubular inclusions and a gravel layer, to address weak soil conditions, seismic activity, and tectonic movements.
2) Subsurface investigations found deep alluvial deposits with low strength and shear wave velocities, posing challenges for the large bridge piers.
3) The foundation concept used capacity design principles, with the gravel layer absorbing inelastic deformations and inclusions providing overstrength to prevent deep failures, allowing sliding if design loads were exceeded.
(2010) - Yates M, Krzeminski M, Berthier D, Hamidi B - The Application of Jet...Michal Krzeminski
Jet grouting was used to construct the Runway End Safety Area for Sydney International Airport. It was needed to bridge over existing structures in a way that stabilized the ground, provided bearing capacity, and created an impermeable barrier. A complex design of jet grout columns with varying diameters, lengths, and reinforcement was implemented based on detailed modeling. Over 1,600 jet grout columns totaling over 13,000 meters in length and 5,100 cubic meters in volume were constructed using a double fluid system to meet the project's geotechnical requirements.
Challenges of Tunneling-- A Peep Into The Exciting World of TunnellingIEI GSC
By Shri Manoj Verman, President, Indian National Group of ISRM
President, International Commission on Hard Rock Excavation
Vice President, Indian Society of Engineering Geology
at 31st National Convention of Civil Engineering
organised by
Gujarat State Center, The Institution of Engineers (India)
at Ahmedabad
1. Careful geological studies are important for selecting dam and reservoir sites to reduce costs and ensure safety and stability.
2. Ideal dam sites have narrow river valleys, competent bedrock like igneous or metamorphic rock near the surface, and favorable geological structures like horizontal or mildly tilted strata.
3. Faults and steeply dipping or folded strata are less desirable as they can compromise the stability and impermeability of the foundation rocks.
1. The document describes the failure of pit slopes at the Deilmann Tailings Management Facility (DTMF) due to collapse of loose outwash sand deposits when resaturated during flooding.
2. Finite element modeling was used to model the stress paths in the sand and ensure stresses did not reach the collapse surface during remediation activities or final flooding. A designed rock buttress was added to prevent triggering of collapse.
3. Geotechnical analyses including limit equilibrium and finite element modeling were used to design slope remediation including flattening slopes and adding a rock buttress to achieve long-term stability with factors of safety over 1.3 and prevent localized collapse triggering.
The document discusses various geological factors that must be considered when constructing tunnels, including: conducting subsurface exploration using pits, adits, drilling, and pilot tunnels; using core drilling and geophysical investigations to interpret geological features; addressing issues related to joint orientation, weathering, faults, rock bursts, and more. Pilot tunnels can help explore critical geological conditions ahead of main excavation and drain rock. The ideal tunnel cross-section depends on the type of rock and purpose of the tunnel.
The pattern of Slopes Pattern in Rock Media
By: Omitogun Solomon T.
Student(MSc. Geology-Engineering Geology/Hydrogeology-2018/2019 set) University of Lagos, Nigeria
solotosin6@gmail.com
The document discusses various types of loads and pressures that act on underground tunnels, including:
1) Earth/rock pressures and water pressure are the most important potential loads. Live loads from surface traffic can usually be neglected.
2) Dimensions of tunnel sections must account for overburden weight (geostatic pressure) or loosening pressure (weight of loosened rock zone).
3) Lateral pressures, bottom pressures, and rock pressures are discussed. Several theories for estimating vertical and lateral loads are presented, including those by Bierbaumer, Terzaghi, and Tsimbaryevitch.
4) Rock pressures depend on factors like the quality of rock, stresses/strains around the
1. The document examines the use of Tunnel Stability Factor (TSF) to estimate convergence and face stability in weak rock tunnels. TSF considers rock mass strength, overburden height, and tunnel size.
2. Parametric numerical analyses were conducted on 74 tunnels varying in size, depth, and rock mass quality. Dimensionless plots of plastic zone radius and convergence vs TSF showed good correlation despite varying conditions.
3. Guidelines for criticality of stability were developed based on convergence-to-radius ratio ranges associated with TSF levels, indicating severe squeezing for TSF < 0.2 and increased risk of collapse below 0.3 without support.
Auvinet exc foundations and geotechnical hazards cfpbolivia
The document provides an overview of geotechnical hazards and challenges for excavations and foundations in Mexico City, where the soft lacustrine clays are highly compressible and susceptible to subsidence. Three key points:
1) The subsoil of Mexico City can be divided into three zones (foothills, transition, lake) with the lake zone containing the most compressible clays. Subsidence rates in some areas exceed 1m per year due to groundwater extraction.
2) Excavations require lateral support systems like sheet piles, diaphragm walls, or precast walls due to the low shear strength of the clays. Design must consider failures of slopes, walls, or the excav
- The document provides information about tunnels and tunneling, including background on some of the earliest tunnels constructed by ancient Egyptians and Babylonians.
- Tunnels can be classified based on their purpose, geological location/condition, and cross-sectional shape. Examples of different tunnel types and shapes are given.
- Key geological conditions that influence tunnel planning and construction are discussed, including rock properties, groundwater conditions, and fault zones. The importance of site investigations is emphasized.
- Methods of tunnel construction in soft ground, dealing with water and gases in tunnels, and controlling temperature are outlined. Excavation methods like cut-and-cover, sequential excavation (drill-and-blast), and tunnel boring
Practices in Planning, Design and Construction of Head Race Tunnel of a Hydro...Mohit Shukla
This paper has been selected for oral presentation as well as inclusion in the conference proceedings of the ICCCGE 2016 : 18th International Conference on Civil,Construction and Geological Engineering held in Toronto, Canada during June,
13-14, 2016. This paper was also able to find a position in the international conference of Dams and Hydropower held at Laos in May 2016.
This document discusses key aspects of engineering geology and its importance in modern development. It provides examples of how poor subsurface conditions, lack of safety measures, and lack of studies can lead to infrastructure failures. It emphasizes the role of engineering geology in properly studying soil and subsurface conditions before construction to select the best design and safety remedies. Methods discussed include field and laboratory investigations to understand rock quality and recommend appropriate structural support.
Detailed Slope Stability Analysis and Assessment of the Original Carsington E...Dr.Costas Sachpazis
A 1225 m long, 35 m high zone earth filled embankment was being constructed from 1981 to 1984 from a British Regional Water Authority to regulate flows in the River Derwent in England. The Carsington Dam was planned to be one of the largest earth filled dams in Britain. Its reservoir capacity was 35 million m3 and the watertight element was Rolled Clay Core with an upstream extension of boot shaped and shoulders of compacted mudstone with horizontal drainage layers of crushed limestone about 4 metres apart and a cut-off grout curtain (Davey and Eccles, 1983).
The downstream slope was 1:2.5 and the upstream slope 1:3. Fill placing began in May 1982 and took three summers, with winter shutdowns. In August 1983 a small berm was placed at the upstream toe to compensate for a faster rate of construction. Earth filling restarted in April 1984 and was one metre below the final crest level on 4 June 1984 when the upstream slope slipped (Skempton, 1985). Observations of pore pressure and settlement were made during construction at four sections and horizontal displacements were observed from August 1983. The Carsington Dam was almost completed on 1984.
However, at the beginning of June 1984, a 400-m length of the upstream shoulder of the embankment dam slipped some 11 m and failed. At the time of the failure, embankment construction was virtually complete with the dam approaching its maximum height of 35 m. Horizontal drainage blankets were incorporated in both the upstream and the downstream shale fill shoulders. Piezometers had been installed and pore pressures were being monitored in the foundation, in the clay core, and in the shoulder fill. The failure surface passed through the boot shaped rolled clay core and a relatively thin layer of surface clay in the foundation of the dam. Investigation of the events at Carsington has made important contributions to the fundamental understanding of the behaviour of large earthworks of this type (Vaughan et al., 1989; Dounias et al., 1996).
The objective of this research is to evaluate a detailed slope stability assessment of the Carsington Earth Embankment Dam in the UK used to retain mine tailings.
By using and applying advanced geotechnical engineering analysis tools and modelling techniques the Carsington Earth Embankment Dam, which is considered a particular geotechnical structure, is analysed.
In the current detailed slope stability analyses the total and effective stress state soil properties / parameters were used, and the most critical slip circle centre according to Fellenius - Jumikis method was initially determined. Subsequently, the Carsington Earth Embankment Dam and its foundation was analysed and examined against failure by slope instability. Considerations of loading conditions which may result to instability for all likely combinations of reservoir and tailwater levels, seepage conditions, both after and during construction were made, and hence three construction and / or loading condit
Analysis and Design Aspects of Support Measures of Main Caverns of Karuma Hyd...IOSRJMCE
The Power house complex of Karuma Hydropower project comprises three main caverns i.e Power house, Transformer Hall and Tailrace surge gallery set at a depth of about 80m in mainly granitic gneiss rock medium. The cavern has been oriented in a N141° direction based on engineering considerations. The principle stress direction is also found nearly parallel to the axis of the caverns and thus the present orientation satisfies both engineering and geotechnical criteria. The support by way of rock anchors and SFRS/ Plain shotcrete has been provided based on analysis using phase 2 software. The underground caverns lie in low geostress field and therefore numerical simulation of excavation of these caverns were done to understand the rock mass behavior during excavation and thus help in design of excavation sequence and rock support. The excavation of all three caverns has since been completed and concrete works are in progress. This paper sums up the 3D simulation analysis of the rock medium and the proposed rock support system for the three caverns.
The document discusses the foundation engineering assessment for installing the world's largest jack-up rig offshore Norway. Based on site investigations, the soil conditions varied across the site and consisted of bedrock overlaid by soft silt/clay and a shallow sand layer. Conventional and finite element analyses proposed constructing sand banks to provide a stable foundation. Three-dimensional finite element modeling of the integrated jack-up structure, skirted spudcan foundations, and soil was used to determine the optimal sand bank geometry. The modeling showed structural forces would remain acceptable during installation, preloading, and storm conditions. The rig was successfully installed, validating the engineering predictions.
1) A magnitude 7.6 earthquake struck Gujarat, India in 2001 near the city of Bachau, causing widespread damage.
2) Two embankment dams, Chang Dam and Fatehgadh Dam, within 150 km of the epicenter were examined. Chang Dam experienced almost a complete collapse likely due to liquefaction of its shallow foundation soils, while Fatehgadh Dam experienced less severe but still significant damage.
3) Analysis of the foundation soils beneath the dams found they were susceptible to liquefaction when saturated, which likely contributed to the observed damage during the earthquake when reservoir levels were low but foundation soils remained saturated.
Mine water risk in open pit slope stabilitySafdar Ali
The document discusses mine water risk and its impact on open pit slope stability. It analyzes the slope stability of a chromite mine in India under three conditions: dry, drained, and undrained. Slope stability analysis was performed using the SLOPE/W software. The factor of safety was highest for the dry condition (1.277) and lowest for the undrained condition (1.230). Proper drainage is required to maintain stability as water can reduce shear strength and increase pore pressure.
ROLE OF GEOLOGY IN SELECTION OF CONSTRUCTION SITE of Mega ProjectsEhsan Ahmed khan
The document discusses the role of geology in selecting construction sites for mega projects. Mega projects are defined as those costing over $1 billion that gain large public attention, such as bridges, tunnels, highways, airports, power plants, and dams. Site selection for mega projects is based on geological factors like geological surveys, bearing capacity, slope stability, water tables, rock type, seismic activity, soil erosion, altitude, and climatic parameters. Geological surveys are needed to understand the site conditions and features. Bearing capacity, seismic activity, slope stability, water content, rock type, soil erosion, soil type, and climatic parameters must all be considered for safe construction and foundation.
The document discusses various theories and approaches for estimating loads and pressures on underground structures like tunnels. It describes how earth/rock pressures, water pressure, and loosening of rock masses can load tunnels. Several theories are explained that take different approaches to estimating vertical loads, lateral pressures, and bottom pressures on tunnels based on factors like depth, soil/rock properties, excavation method, and structural support. Key theorists discussed include Bierbäumer, Terzaghi, Tsimbaryevitch, and others and their formulas for calculating various pressure types on tunnels.
The Rion-Antirion Bridge in Greece connects the Peloponnese peninsula and western Greece over the Gulf of Corinth. It presents significant engineering challenges due to deep and weak soil, large water depths of up to 65 meters, and high seismic activity. The innovative design features 90 meter diameter foundations reinforced with steel inclusions resting on soil and a 2,252 meter continuous cable-stayed deck fully suspended from pylons. Unconventional construction methods were required such as building foundation components in a dry dock and using a tension-leg barge for underwater work.
Post Earthquack Slope Stability Analysis of Rubble Mound BreakwaterIJERA Editor
Rubble mound breakwaters are structures built mainly of quarried rock. Generally armourstone or artificial concrete armour units are used for the outer armour layer,which should protect the structure againist wave attack. Armour stones and concrete armoure unites in this outer layer are usually placed with care to obtain effective interlocking and consequently better stability
Groundwater can affect engineering structures through several mechanisms:
- It can erode foundations, cause settlement or collapse through volume changes in soil/rock.
- Increase moisture in slopes, reducing stability and increasing landslide risk.
- Impact excavation and construction by flowing towards work sites.
- Reduce bearing capacity and shear strength of soils.
- Cause uplift pressures that can lead to failure of structures.
Proper site investigation is needed to understand subsurface water conditions and mitigate risks.
This document discusses the importance of engineering geology in dam construction. There are three main types of dams - arc or buttress dams, gravity dams, and embankment dams - which experience different forces. Proper geological investigations are required to ensure the stability and safety of the dam foundation, the water-tightness of the reservoir, and slope stability. Preliminary geological investigations include topographical studies, reservoir location analysis, petrology studies, structural geology studies, and examining foundation conditions. Detailed investigations involve making a detailed geological map, studying rock types, structures, seismic data, and interpreting core drill samples to understand the engineering geological properties of the area.
This document discusses ground investigation for tunnelling projects. It covers objectives of ground investigation planning including suitability assessment, design, construction planning and environmental impact determination. Key risks like water ingress, ground collapse and obstructions are highlighted. Common ground conditions like dykes, wedges and timber piles are shown. Strategies and techniques for ground investigation planning, during design and construction stages are outlined. Methods for different ground types like soft ground, hard rock and karst deposits are also described. The document emphasizes comprehensive planning and supervision of ground investigation works for tunnelling projects.
A presentation about roads and highways- it's study and also some problems after the construction of roads.the presentation also contains pictures of complicated regions for road construction.
This document describes 4 autonomic function tests used to assess the cardiovascular system: 1) Heart rate variation during respiration measures vagal control of heart rate, 2) Heart rate variation during postural change assesses parasympathetic response, 3) The Valsalva maneuver evaluates sympathetic and parasympathetic function through blood pressure and heart rate responses in 4 phases, 4) The cold pressor test increases blood pressure through sympathetic discharge triggered by cold stress. These tests are used to evaluate autonomic nervous system function.
Neuromuscular junction blockers are useful in general anesthesia and surgery by causing muscle paralysis. The earliest known muscle relaxant was curare, used as arrow poison by indigenous peoples in South America. Modern neuromuscular blockers include atracurium and tubocurarine. There are two main types - non-depolarizing blockers that compete with acetylcholine for receptors, and depolarizing blockers that act like acetylcholine but resist breakdown.
The pattern of Slopes Pattern in Rock Media
By: Omitogun Solomon T.
Student(MSc. Geology-Engineering Geology/Hydrogeology-2018/2019 set) University of Lagos, Nigeria
solotosin6@gmail.com
The document discusses various types of loads and pressures that act on underground tunnels, including:
1) Earth/rock pressures and water pressure are the most important potential loads. Live loads from surface traffic can usually be neglected.
2) Dimensions of tunnel sections must account for overburden weight (geostatic pressure) or loosening pressure (weight of loosened rock zone).
3) Lateral pressures, bottom pressures, and rock pressures are discussed. Several theories for estimating vertical and lateral loads are presented, including those by Bierbaumer, Terzaghi, and Tsimbaryevitch.
4) Rock pressures depend on factors like the quality of rock, stresses/strains around the
1. The document examines the use of Tunnel Stability Factor (TSF) to estimate convergence and face stability in weak rock tunnels. TSF considers rock mass strength, overburden height, and tunnel size.
2. Parametric numerical analyses were conducted on 74 tunnels varying in size, depth, and rock mass quality. Dimensionless plots of plastic zone radius and convergence vs TSF showed good correlation despite varying conditions.
3. Guidelines for criticality of stability were developed based on convergence-to-radius ratio ranges associated with TSF levels, indicating severe squeezing for TSF < 0.2 and increased risk of collapse below 0.3 without support.
Auvinet exc foundations and geotechnical hazards cfpbolivia
The document provides an overview of geotechnical hazards and challenges for excavations and foundations in Mexico City, where the soft lacustrine clays are highly compressible and susceptible to subsidence. Three key points:
1) The subsoil of Mexico City can be divided into three zones (foothills, transition, lake) with the lake zone containing the most compressible clays. Subsidence rates in some areas exceed 1m per year due to groundwater extraction.
2) Excavations require lateral support systems like sheet piles, diaphragm walls, or precast walls due to the low shear strength of the clays. Design must consider failures of slopes, walls, or the excav
- The document provides information about tunnels and tunneling, including background on some of the earliest tunnels constructed by ancient Egyptians and Babylonians.
- Tunnels can be classified based on their purpose, geological location/condition, and cross-sectional shape. Examples of different tunnel types and shapes are given.
- Key geological conditions that influence tunnel planning and construction are discussed, including rock properties, groundwater conditions, and fault zones. The importance of site investigations is emphasized.
- Methods of tunnel construction in soft ground, dealing with water and gases in tunnels, and controlling temperature are outlined. Excavation methods like cut-and-cover, sequential excavation (drill-and-blast), and tunnel boring
Practices in Planning, Design and Construction of Head Race Tunnel of a Hydro...Mohit Shukla
This paper has been selected for oral presentation as well as inclusion in the conference proceedings of the ICCCGE 2016 : 18th International Conference on Civil,Construction and Geological Engineering held in Toronto, Canada during June,
13-14, 2016. This paper was also able to find a position in the international conference of Dams and Hydropower held at Laos in May 2016.
This document discusses key aspects of engineering geology and its importance in modern development. It provides examples of how poor subsurface conditions, lack of safety measures, and lack of studies can lead to infrastructure failures. It emphasizes the role of engineering geology in properly studying soil and subsurface conditions before construction to select the best design and safety remedies. Methods discussed include field and laboratory investigations to understand rock quality and recommend appropriate structural support.
Detailed Slope Stability Analysis and Assessment of the Original Carsington E...Dr.Costas Sachpazis
A 1225 m long, 35 m high zone earth filled embankment was being constructed from 1981 to 1984 from a British Regional Water Authority to regulate flows in the River Derwent in England. The Carsington Dam was planned to be one of the largest earth filled dams in Britain. Its reservoir capacity was 35 million m3 and the watertight element was Rolled Clay Core with an upstream extension of boot shaped and shoulders of compacted mudstone with horizontal drainage layers of crushed limestone about 4 metres apart and a cut-off grout curtain (Davey and Eccles, 1983).
The downstream slope was 1:2.5 and the upstream slope 1:3. Fill placing began in May 1982 and took three summers, with winter shutdowns. In August 1983 a small berm was placed at the upstream toe to compensate for a faster rate of construction. Earth filling restarted in April 1984 and was one metre below the final crest level on 4 June 1984 when the upstream slope slipped (Skempton, 1985). Observations of pore pressure and settlement were made during construction at four sections and horizontal displacements were observed from August 1983. The Carsington Dam was almost completed on 1984.
However, at the beginning of June 1984, a 400-m length of the upstream shoulder of the embankment dam slipped some 11 m and failed. At the time of the failure, embankment construction was virtually complete with the dam approaching its maximum height of 35 m. Horizontal drainage blankets were incorporated in both the upstream and the downstream shale fill shoulders. Piezometers had been installed and pore pressures were being monitored in the foundation, in the clay core, and in the shoulder fill. The failure surface passed through the boot shaped rolled clay core and a relatively thin layer of surface clay in the foundation of the dam. Investigation of the events at Carsington has made important contributions to the fundamental understanding of the behaviour of large earthworks of this type (Vaughan et al., 1989; Dounias et al., 1996).
The objective of this research is to evaluate a detailed slope stability assessment of the Carsington Earth Embankment Dam in the UK used to retain mine tailings.
By using and applying advanced geotechnical engineering analysis tools and modelling techniques the Carsington Earth Embankment Dam, which is considered a particular geotechnical structure, is analysed.
In the current detailed slope stability analyses the total and effective stress state soil properties / parameters were used, and the most critical slip circle centre according to Fellenius - Jumikis method was initially determined. Subsequently, the Carsington Earth Embankment Dam and its foundation was analysed and examined against failure by slope instability. Considerations of loading conditions which may result to instability for all likely combinations of reservoir and tailwater levels, seepage conditions, both after and during construction were made, and hence three construction and / or loading condit
Analysis and Design Aspects of Support Measures of Main Caverns of Karuma Hyd...IOSRJMCE
The Power house complex of Karuma Hydropower project comprises three main caverns i.e Power house, Transformer Hall and Tailrace surge gallery set at a depth of about 80m in mainly granitic gneiss rock medium. The cavern has been oriented in a N141° direction based on engineering considerations. The principle stress direction is also found nearly parallel to the axis of the caverns and thus the present orientation satisfies both engineering and geotechnical criteria. The support by way of rock anchors and SFRS/ Plain shotcrete has been provided based on analysis using phase 2 software. The underground caverns lie in low geostress field and therefore numerical simulation of excavation of these caverns were done to understand the rock mass behavior during excavation and thus help in design of excavation sequence and rock support. The excavation of all three caverns has since been completed and concrete works are in progress. This paper sums up the 3D simulation analysis of the rock medium and the proposed rock support system for the three caverns.
The document discusses the foundation engineering assessment for installing the world's largest jack-up rig offshore Norway. Based on site investigations, the soil conditions varied across the site and consisted of bedrock overlaid by soft silt/clay and a shallow sand layer. Conventional and finite element analyses proposed constructing sand banks to provide a stable foundation. Three-dimensional finite element modeling of the integrated jack-up structure, skirted spudcan foundations, and soil was used to determine the optimal sand bank geometry. The modeling showed structural forces would remain acceptable during installation, preloading, and storm conditions. The rig was successfully installed, validating the engineering predictions.
1) A magnitude 7.6 earthquake struck Gujarat, India in 2001 near the city of Bachau, causing widespread damage.
2) Two embankment dams, Chang Dam and Fatehgadh Dam, within 150 km of the epicenter were examined. Chang Dam experienced almost a complete collapse likely due to liquefaction of its shallow foundation soils, while Fatehgadh Dam experienced less severe but still significant damage.
3) Analysis of the foundation soils beneath the dams found they were susceptible to liquefaction when saturated, which likely contributed to the observed damage during the earthquake when reservoir levels were low but foundation soils remained saturated.
Mine water risk in open pit slope stabilitySafdar Ali
The document discusses mine water risk and its impact on open pit slope stability. It analyzes the slope stability of a chromite mine in India under three conditions: dry, drained, and undrained. Slope stability analysis was performed using the SLOPE/W software. The factor of safety was highest for the dry condition (1.277) and lowest for the undrained condition (1.230). Proper drainage is required to maintain stability as water can reduce shear strength and increase pore pressure.
ROLE OF GEOLOGY IN SELECTION OF CONSTRUCTION SITE of Mega ProjectsEhsan Ahmed khan
The document discusses the role of geology in selecting construction sites for mega projects. Mega projects are defined as those costing over $1 billion that gain large public attention, such as bridges, tunnels, highways, airports, power plants, and dams. Site selection for mega projects is based on geological factors like geological surveys, bearing capacity, slope stability, water tables, rock type, seismic activity, soil erosion, altitude, and climatic parameters. Geological surveys are needed to understand the site conditions and features. Bearing capacity, seismic activity, slope stability, water content, rock type, soil erosion, soil type, and climatic parameters must all be considered for safe construction and foundation.
The document discusses various theories and approaches for estimating loads and pressures on underground structures like tunnels. It describes how earth/rock pressures, water pressure, and loosening of rock masses can load tunnels. Several theories are explained that take different approaches to estimating vertical loads, lateral pressures, and bottom pressures on tunnels based on factors like depth, soil/rock properties, excavation method, and structural support. Key theorists discussed include Bierbäumer, Terzaghi, Tsimbaryevitch, and others and their formulas for calculating various pressure types on tunnels.
The Rion-Antirion Bridge in Greece connects the Peloponnese peninsula and western Greece over the Gulf of Corinth. It presents significant engineering challenges due to deep and weak soil, large water depths of up to 65 meters, and high seismic activity. The innovative design features 90 meter diameter foundations reinforced with steel inclusions resting on soil and a 2,252 meter continuous cable-stayed deck fully suspended from pylons. Unconventional construction methods were required such as building foundation components in a dry dock and using a tension-leg barge for underwater work.
Post Earthquack Slope Stability Analysis of Rubble Mound BreakwaterIJERA Editor
Rubble mound breakwaters are structures built mainly of quarried rock. Generally armourstone or artificial concrete armour units are used for the outer armour layer,which should protect the structure againist wave attack. Armour stones and concrete armoure unites in this outer layer are usually placed with care to obtain effective interlocking and consequently better stability
Groundwater can affect engineering structures through several mechanisms:
- It can erode foundations, cause settlement or collapse through volume changes in soil/rock.
- Increase moisture in slopes, reducing stability and increasing landslide risk.
- Impact excavation and construction by flowing towards work sites.
- Reduce bearing capacity and shear strength of soils.
- Cause uplift pressures that can lead to failure of structures.
Proper site investigation is needed to understand subsurface water conditions and mitigate risks.
This document discusses the importance of engineering geology in dam construction. There are three main types of dams - arc or buttress dams, gravity dams, and embankment dams - which experience different forces. Proper geological investigations are required to ensure the stability and safety of the dam foundation, the water-tightness of the reservoir, and slope stability. Preliminary geological investigations include topographical studies, reservoir location analysis, petrology studies, structural geology studies, and examining foundation conditions. Detailed investigations involve making a detailed geological map, studying rock types, structures, seismic data, and interpreting core drill samples to understand the engineering geological properties of the area.
This document discusses ground investigation for tunnelling projects. It covers objectives of ground investigation planning including suitability assessment, design, construction planning and environmental impact determination. Key risks like water ingress, ground collapse and obstructions are highlighted. Common ground conditions like dykes, wedges and timber piles are shown. Strategies and techniques for ground investigation planning, during design and construction stages are outlined. Methods for different ground types like soft ground, hard rock and karst deposits are also described. The document emphasizes comprehensive planning and supervision of ground investigation works for tunnelling projects.
A presentation about roads and highways- it's study and also some problems after the construction of roads.the presentation also contains pictures of complicated regions for road construction.
This document describes 4 autonomic function tests used to assess the cardiovascular system: 1) Heart rate variation during respiration measures vagal control of heart rate, 2) Heart rate variation during postural change assesses parasympathetic response, 3) The Valsalva maneuver evaluates sympathetic and parasympathetic function through blood pressure and heart rate responses in 4 phases, 4) The cold pressor test increases blood pressure through sympathetic discharge triggered by cold stress. These tests are used to evaluate autonomic nervous system function.
Neuromuscular junction blockers are useful in general anesthesia and surgery by causing muscle paralysis. The earliest known muscle relaxant was curare, used as arrow poison by indigenous peoples in South America. Modern neuromuscular blockers include atracurium and tubocurarine. There are two main types - non-depolarizing blockers that compete with acetylcholine for receptors, and depolarizing blockers that act like acetylcholine but resist breakdown.
This document contains information about Sri Lankan artist Vajira Gunawardena and lists some of their artworks. It provides titles, dimensions, materials and collection locations for 13 paintings created between 2010-2015. It also mentions a large acrylic painting commissioned for the Chaaya Tranz Hotel Lobby in Sri Lanka and a 2002 cement monument titled "Monument for Peace". The document concludes by listing "Paper articles" among the artist's other works.
The document summarizes key aspects of cerebrospinal fluid (CSF) including its formation, circulation, composition, and functions such as cushioning the brain. CSF is produced in the choroid plexuses at a rate of 500 ml per day, circulates around the brain and spinal cord in ventricles and subarachnoid spaces, and is absorbed by arachnoid villi. It has a similar composition to plasma but contains less protein and glucose. The blood-brain and blood-CSF barriers regulate passage of substances between blood and CSF. Increased CSF pressure can occur if absorption is blocked.
The document summarizes several aspects of regional circulations, including the coronary, cutaneous, cerebral, skeletal muscle, splanchnic, and renal circulations. Specific details provided on the coronary circulation include its high blood flow even at rest, regulation of flow through metabolic and neural mechanisms, and implications for conditions like myocardial infarction and heart failure. Key aspects of the cutaneous circulation discussed are its role in temperature regulation through sympathetic nervous system control of arterioles and anastomoses, and local vasodilation or constriction in response to heating and cooling.
The motor nervous system is comprised of several components that work together in a hierarchical manner to control movement. At the highest level are secondary motor areas like the supplementary motor area and premotor cortex that plan movements. Lower levels include the primary motor cortex, corticospinal tract, lower motor neurons, and skeletal muscles. Other components that assist in motor control are the cerebellum for coordination, basal ganglia for movement execution, and spinal cord for reflexes. Damage at different levels of this hierarchy can result in different motor impairments.
This document summarizes several key aspects of cerebral circulation:
1) The brain has the highest blood flow of any organ and is least tolerant of ischemia, relying on a dual internal carotid and vertebral arterial supply forming the Circle of Willis to maintain constant blood flow.
2) Cerebral circulation has unique features like being enclosed in the rigid skull, maintaining a constant volume through autoregulation of blood flow in response to pressure changes.
3) Local cerebral blood flow is tightly regulated by a combination of myogenic and metabolic mechanisms to ensure adequate oxygen and nutrient delivery to brain tissue.
The stretch reflex is a monosynaptic reflex where stimulation of muscle spindles by muscle stretch leads to contraction of the same muscle. When the muscle is stretched, Ia afferents are activated and signal the spinal cord to stimulate alpha motor neurons, contracting the muscle. The inverse stretch reflex detects undue muscle tension via Golgi tendon organs and relaxes the muscle through Ib afferent inhibition of alpha motor neurons. Deep tendon reflexes like the knee jerk test spinal cord integrity by examining reflexes at different levels. Primitive reflexes are present in infants and assess development.
There are three main levels of control involved in maintaining posture: spinal, brainstem, and cortical. At the spinal level, stretch reflexes and supporting reactions maintain static stability. At the brainstem level, labyrinthine reflexes and tonic neck reflexes react to gravitational pull and head position. At the cortical level, visual and proprioceptive cues integrate to allow for complex postural adjustments.
This document discusses the human sensory system, including sensory receptors, pathways, and cortex. It describes the different sensory modalities and sensations. The main sensory pathways are the dorsal column-medial lemniscus pathway and spinothalamic pathway, which transmit signals from receptors to the thalamus and sensory cortex. Within the cortex, different body regions are represented in a distorted map called a sensory homunculus. The document provides details on various mechanoreceptors, transduction of stimuli to action potentials, and coding of sensory information.
The Rion Antirion Bridge project involves constructing a 3 km long multi-cable stayed bridge across the Gulf of Corinth in western Greece. It will be one of the largest bridges of its type in the world. The project faces significant engineering challenges due to high seismic activity in the region, deep weak soil layers, and the potential for fault displacements. Sophisticated dynamic analyses and foundation designs were required to develop a structure that can withstand strong earthquakes while maintaining serviceability. The bridge design utilizes seismic isolation of the deck and innovative reinforced soil foundations to improve bearing capacity and control failure modes under high seismic loads.
This document discusses the seismic design of foundations for the Rion Antirion Bridge in Greece. It describes the challenging soil and seismic conditions at the site, which required innovative foundation design. The foundations consist of large diameter caissons resting on top of reinforced natural ground, with steel tubular inclusions driven into the soil to increase its strength. Three of the four bridge piers use this reinforced foundation solution, while the fourth pier's caisson rests directly on a thick gravel layer without inclusions. The document outlines the design process and considerations, which aimed to ensure the foundations could adequately resist the large earthquake and ship impact loads expected at the seismically active site with poor soil conditions.
The Rion-Antirion Bridge in Greece connects the Peloponnese peninsula to the western mainland via a 2252m long cable-stayed main bridge that spans the Corinth Strait. It was designed to withstand the severe seismic activity and possible fault movements in the area. The main bridge uses four pylons supported by large reinforced soil foundations to distribute seismic forces to the deep weak soil layers. Dynamic analysis showed that during major earthquakes, the reinforced soil and pylon foundations would yield and slide as designed to dissipate energy without compromising the structure. The continuous suspended deck acts as a flexible element that can accommodate displacements without damage. The bridge's innovative design allows all components to work together to resist earthquake forces through
This document discusses the foundation design processes for two major bridge projects - the Vasco da Gama Bridge in Lisbon, Portugal and the Rion-Antirion Bridge in Greece. For the Vasco da Gama Bridge, the foundations consisted of vertical large diameter bored concrete piles due to favorable soil conditions and design requirements. For the Rion-Antirion Bridge, the soil conditions were less favorable so an innovative foundation concept was developed and implemented, which allowed for some permanent displacement under seismic loading. The additional time for design of the Rion-Antirion Bridge was crucial to developing and validating this new foundation solution.
The document discusses literature related to longwall mining geo-technical studies conducted at Ramagundam region in SCCL, India. It summarizes the key findings from 9 completed longwall panels at GDK.10A incline mine including production trends, geological conditions, equipment specifications, and analyses of caving behavior and periodic weighting distances for different panel lengths. Face length was found to influence main and periodic fall spans, with main fall varying between 63-78m for face lengths from 90-170m.
This document summarizes the design and construction of the Rion-Antirion Bridge in Greece. Some key points:
- The bridge spans 2,252 meters over the Gulf of Corinth and connects the Peloponnese to mainland Greece. It was completed in 2004.
- The environment presented challenges like deep water, weak soil, seismic activity, and strong winds. Foundations consisted of large caissons on reinforced soil with steel inclusions.
- The cable-stayed bridge has a continuous and fully suspended steel-concrete deck. It is equipped with seismic dissipation systems including hydraulic dampers to absorb energy from earthquakes.
- Innovative designs like the soil reinforcement and seismic protection
DYNAMIC ANALYSIS OF CONCRETE GIRDER BRIDGES UNDER STRONG EARTHQUAKES: THE EFF...IAEME Publication
This paper presents the dynamic analysis of concrete girder bridges taking into account the effect of collision on parapet wall. In addition, adopting of seismic isolation rubber on pier structure and wing wall on parapet were analyzed. Two spans concrete girder bridges with variation of gap were examined in theoretically by 3D FEM model of ABAQUS. The abutment was simplified by parapet wall which was modeled by 3D reinforced concrete structure. In order to examine the seismic behavior of bridge, six different inputs of seismic ground accelerations were applied at footing of pier structure.
The document provides details about the Mumbai Coastal Road Project which includes construction of India's first undersea tunnel. Some key points:
1) A 2.07 km long twin tunnel is being constructed as part of the project, with 1 km being under the sea, making it unique from other tunnels worldwide.
2) India's largest Tunnel Boring Machine (TBM) named 'Mavala' has been deployed to excavate the tunnel and broke excavation records.
3) The tunnels will be 11 meters in diameter and constructed using concrete segmental lining for structural support and stability.
4) Numerical analysis of stress redistribution during various construction stages and the long-term condition will be conducted
1. The document discusses applying the convergence-confinement approach to analyze rock-lining interaction in tunnels using the Shimizu Tunnel case study.
2. It constructs ground reaction and support characteristic curves for different support systems - steel ribs, shotcrete, and rock bolts used in Shimizu Tunnel.
3. By intersecting the curves, it determines the design load carried by each support system when the ground and lining reach equilibrium after tunnel excavation.
This document discusses various topics related to seismic design, including:
- Seismicity and plate tectonics, which show that most earthquakes occur at plate boundaries.
- Different types of earthquakes like intraplate and reservoir-induced seismicity. Reservoir-induced seismicity can occur due to rapid reservoir filling or fluctuations in water level.
- Effects of soil conditions like basin effects that can amplify seismic ground motions. Soft soils in large basins like Mexico City significantly amplified motions from a distant earthquake, contributing to extensive damage.
- Key geotechnical aspects impacting seismic design like liquefaction, plasticity index, and shear wave velocity and how they relate to soil behavior during earthquakes
Explosive Compaction of Foundation Soils Seymour Falls DamDario Gnoato
The document summarizes the explosive compaction project used to densify foundation soils for the seismic upgrade of the Seymour Falls Dam in Vancouver, BC. Explosive compaction involved drilling over 800 blast holes and detonating sequential charges to induce compaction through liquefaction and reconsolidation of soils. Strict limits were placed on explosives selection, blast designs, and monitoring to minimize impacts to nearby structures and fish hatchery. The project successfully achieved the targeted 2-5% volumetric strain in soils through a bottom-up sequence of three blast passes across 18 panels using electronic detonators and emulsion explosives.
High-Resolution 3D Seismic: Coal Mines FieldsAli Osman Öncel
1. CONSOL developed a robust coal geophysics program between 1985-2000 that utilized various seismic and non-seismic methods to address exploration, engineering, and environmental challenges.
2. A key case study involved using high-resolution 3D surface seismic data to detect a complex geologic anomaly called a "roll" in a coal seam, which showed up as amplitude anomalies.
3. Interpretation of the 3D seismic data found that the roll meandered into the property from the north and turned southeast, allowing mine plans to be adjusted to account for more difficult mining conditions on the roll's western flank.
The document discusses piles and their application in building tall structures like the Burj Khalifa. It describes how 192 piles that were 47 meters long supported the Burj Khalifa's foundation. The piles transmitted loads to hard rock 50 meters below through friction and end bearing. Challenges included weak soil and groundwater, which required using a polymer slurry during excavation to keep boreholes open until concrete was pumped in.
Main objective of the executed researches was justification of the location of entry
providing its maintenance in a bearing pressure zone. Researches were carried out for
conditions of the Prokopyevsk and Kiselevsky field of the Kuznetsk coal basin
(Russia). Researches were conducted by a finite element method. When performing
researches the provision entry relative of a regional part of the massif and property of
coal changed. As a result of researches influence of strength of coal and the location
of entry on the stress and strain state of the massif is established and the conclusion is
drawn on need of increase in height of a slice up to 10 m. Recommendations of
increase in height of each subsequent slice at mining of soft coals are also made. The
novelty of work consists in establishment of dependences of the stress and strain state
of the massif on height of the mining slice.
“DYNAMIC ANALYSIS OF GRAVITY RETAINING WALL WITH SOIL STRUCTURE INTERACTION”IRJET Journal
This document presents a study on the dynamic analysis of gravity retaining walls considering soil-structure interaction. It discusses how the interaction between retaining walls and surrounding soil becomes complex under dynamic loads like earthquakes. It develops a numerical model using finite element methods to simulate the coupled behavior of the retaining wall and underlying soil. The soil is modeled using constitutive models that capture its nonlinear and dynamic properties, while the retaining wall is modeled as either rigid or flexible. It analyzes the effects of soil-structure interaction on the dynamic response of gravity retaining walls under different heights and profiles. The maximum and minimum deformations and stresses obtained from the analysis are plotted against the height ratio to study their variations.
The document discusses tunnelling and geological aspects of tunnelling. It provides details on the history and types of tunnels, benefits of tunnels, tunnel construction equipment, and geological considerations for tunnel design including rock mass characterization, structural mapping, discontinuity analysis, and instability mechanisms. Key blocks and maximum wedge theories are described for evaluating potential rock failures around tunnel excavations.
The document summarizes a project to construct a 5.4km sewer tunnel passing under rail lines and a motorway in an urban area of Glasgow with a complex geotechnical environment due to historic mining. A detailed ground investigation program was implemented, encountering two incidents of mine workings requiring remediation. A complex geotechnical model was developed to quantify risks like mine shafts, compressible soil, and variable bedrock. The GBR-B and GBR-C will form the basis for contractor pricing and compensation for issues encountered during construction.
This document discusses earthquake geotechnical engineering and its practices. It describes various earthquake hazards such as ground shaking, liquefaction, landslides, and retaining structure failure. It then discusses how earthquake damage depends on factors like magnitude, distance from epicenter, site properties, and structure properties. Specific failure modes are explored like soft first story collapse, foundation detachment, and bridge abutment failure. The document examines geomorphological changes caused by earthquakes and various techniques for ground improvement to mitigate liquefaction hazards.
This document describes the development of an original testing apparatus for conducting rapid pull-out tests on geotextile reinforcements embedded in soil. The testing apparatus allows investigating shear velocities of 0.1 to 1.2 m/s to simulate dynamic loadings on soil-geotextile interfaces, such as those found in rockfall protection structures. Preliminary tests were conducted using a free-falling weight to pull a geotextile strip out of a soil-filled tank. Measurements of pull-out force, and displacements of the geotextile head and rear, allowed calculating parameters like shear stress and friction length. The results provide initial insights into the soil-geotextile interface response under rapid
Full Paper - Ratcheting Uplift of Buried Pipelines in Sand (P. Chitas)Pagkratios Chitas
This document summarizes an experimental study on the ratcheting failure mechanism of buried offshore pipelines in sand. Small-scale laboratory tests were conducted using a pipe section buried in dry silica sand at various densities and embedment depths. Both monotonic and cyclic (load-controlled) pull-out tests were performed to simulate upheaval buckling and ratcheting failure. The test results were analyzed to investigate controlling parameters, validate prediction methods, and determine adequate soil cover required to resist ratcheting. The experimental setup, soil sample preparation, and testing procedure are described in detail.
La Unión Europea ha acordado un embargo petrolero contra Rusia en respuesta a su invasión de Ucrania. El embargo prohibirá la mayoría de las importaciones de petróleo ruso a la UE y se implementará de manera gradual durante los próximos seis meses. La medida es la sanción económica más dura contra Rusia hasta la fecha y tiene como objetivo aumentar la presión sobre el gobierno de Putin para que ponga fin a la guerra.
The Rion-Antirion Bridge connects Greece across a strait prone to earthquakes. Its 2,252 meter long deck is suspended from four pylons by stay cables. To protect the bridge from seismic events, innovative energy dissipation systems were used, including viscous dampers and fuse restraints. Extensive testing of full-scale prototypes confirmed the design assumptions and behavior of the seismic protection system. The dampers and restraints limit deck movement during earthquakes while dissipating seismic energy. The fuse restraints fail under strong quakes, allowing the dampers to control deck oscillations. Similar systems isolate the approach viaducts from ground motions.
This document discusses ground reinforcement in seismic areas to improve the bearing capacity of shallow foundations. It presents the yield design theory framework for evaluating seismic bearing capacity, which defines a bounding surface delimiting allowable load combinations. This framework has been extended to a new design concept using soil reinforcement with inclusions to significantly improve foundation seismic bearing capacity. Numerical studies and experiments have validated this concept and the theoretical tools.
Patras 4th congress on steel structuresgefyra-rion
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive function. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms.
This document summarizes wind tunnel experiments investigating rain-wind induced vibration of inclined bridge stays. Key findings include:
1) Vibration occurred over a narrow wind speed range and was dependent on the presence of a thin water film on the stay surface.
2) Pressure and water thickness sensors on a model stay measured lift forces and water movement correlated with vibration. Lift force peaks preceded increases in vibration amplitude.
3) A physical model was developed explaining how small changes in water film thickness could alter boundary layer flow and pressure fields, driving vibration.
4) Tests on two larger stay diameters validated the model, showing vibration control through surface texturing that disrupted water flow without drag penalties.
This document discusses centrifuge tests that were conducted to validate an innovative foundation concept for the Rion Antirion bridge in Greece. The tests were conducted at a scale of 1/100 to simulate the behavior of the foundation system under various loading conditions. The tests validated the theoretical predictions of the foundation's bearing capacity and identified its failure mechanism under combined shear and overturning loads. Key results showed the development of pore pressures and bending moments in the foundation inclusions under cyclic loading, as well as a critical shear force of around 45 MN where bending moments increased rapidly. The centrifuge tests proved the validity of the innovative foundation concept and the design tools used.
On January 27, 2005, a lightning strike caused a fire on a stay cable of a cable-stayed bridge, leading to the failure of the cable. Tests and investigations were conducted to understand the failure mechanism and develop protection solutions. It was found that the lightning struck near a metallic collar, igniting a small fire that did not self-extinguish due to wind and rain. To prevent future failures, stretch wires were installed above stay cables to intercept strikes, and pylon protection was enhanced according to new standards to reduce direct strikes to cables.
The Rion-Antirion bridge in Greece experienced vibrations in its lightning protection cables after their installation. Wind tunnel testing revealed that the vibrations were due to galloping caused by the compact arrangement of the three stainless steel ropes. Reconfiguring the ropes with spacers to separate them was found to suppress the galloping without additional damping. Alternative solutions like adding viscous dampers would only work if a high level of damping could be achieved. It was decided to change the rope arrangement with spacers to provide both separation and additional damping to resolve the vibration issues.
The document discusses the benefits of exercise for mental health. Regular physical activity can help reduce anxiety and depression and improve mood and cognitive function. Exercise causes chemical changes in the brain that may help protect against mental illness and improve symptoms.
The document describes the seismic protection systems for the Rion-Antirion Bridge in Greece, which crosses an active seismic strait. The main bridge's continuous deck is suspended from four tall pylons and protected using fluid viscous dampers and fuse restraints connecting the deck to pylons. The dampers dissipate energy during earthquakes after the restraints fail at a predetermined force. Similar dampers and elastomeric isolators protect the approach viaducts. Full-scale tests on prototype dampers and restraints were conducted at laboratories in Italy and the US to verify the devices could withstand accelerations up to 0.48g as designed.
Fib2010 article269 june 2008 eq case study_rev_agefyra-rion
The Rion-Antirion Bridge in Greece withstood the 2008 Mw 6.5 Achaia-Ilia earthquake without structural damage. The bridge's seismic design included energy dissipation devices and sacrificial fuses that were activated during the quake as intended. Post-earthquake inspections confirmed yielding of all lateral fuses while minor non-structural damage occurred. Data from the bridge's monitoring system was analyzed to evaluate the bridge's response and performance of the seismic design elements during the strong shaking event.
1) The concrete durability strategy for the Rion-Antirion Bridge project focused on controlling corrosion of embedded steel by reducing chloride penetration through proper definition of exposure zones, concrete covers, and characterization of concrete mixes.
2) Specific tests were performed on concrete mixes to evaluate durability parameters such as rapid chloride penetration, water penetration, chloride diffusion coefficient, and oxygen permeability.
3) Strict quality assurance/quality control procedures were followed during construction to ensure the in-situ concrete quality matched specifications and laboratory results.
Skybuffer AI: Advanced Conversational and Generative AI Solution on SAP Busin...Tatiana Kojar
Skybuffer AI, built on the robust SAP Business Technology Platform (SAP BTP), is the latest and most advanced version of our AI development, reaffirming our commitment to delivering top-tier AI solutions. Skybuffer AI harnesses all the innovative capabilities of the SAP BTP in the AI domain, from Conversational AI to cutting-edge Generative AI and Retrieval-Augmented Generation (RAG). It also helps SAP customers safeguard their investments into SAP Conversational AI and ensure a seamless, one-click transition to SAP Business AI.
With Skybuffer AI, various AI models can be integrated into a single communication channel such as Microsoft Teams. This integration empowers business users with insights drawn from SAP backend systems, enterprise documents, and the expansive knowledge of Generative AI. And the best part of it is that it is all managed through our intuitive no-code Action Server interface, requiring no extensive coding knowledge and making the advanced AI accessible to more users.
Main news related to the CCS TSI 2023 (2023/1695)Jakub Marek
An English 🇬🇧 translation of a presentation to the speech I gave about the main changes brought by CCS TSI 2023 at the biggest Czech conference on Communications and signalling systems on Railways, which was held in Clarion Hotel Olomouc from 7th to 9th November 2023 (konferenceszt.cz). Attended by around 500 participants and 200 on-line followers.
The original Czech 🇨🇿 version of the presentation can be found here: https://www.slideshare.net/slideshow/hlavni-novinky-souvisejici-s-ccs-tsi-2023-2023-1695/269688092 .
The videorecording (in Czech) from the presentation is available here: https://youtu.be/WzjJWm4IyPk?si=SImb06tuXGb30BEH .
This presentation provides valuable insights into effective cost-saving techniques on AWS. Learn how to optimize your AWS resources by rightsizing, increasing elasticity, picking the right storage class, and choosing the best pricing model. Additionally, discover essential governance mechanisms to ensure continuous cost efficiency. Whether you are new to AWS or an experienced user, this presentation provides clear and practical tips to help you reduce your cloud costs and get the most out of your budget.
Skybuffer SAM4U tool for SAP license adoptionTatiana Kojar
Manage and optimize your license adoption and consumption with SAM4U, an SAP free customer software asset management tool.
SAM4U, an SAP complimentary software asset management tool for customers, delivers a detailed and well-structured overview of license inventory and usage with a user-friendly interface. We offer a hosted, cost-effective, and performance-optimized SAM4U setup in the Skybuffer Cloud environment. You retain ownership of the system and data, while we manage the ABAP 7.58 infrastructure, ensuring fixed Total Cost of Ownership (TCO) and exceptional services through the SAP Fiori interface.
How to Interpret Trends in the Kalyan Rajdhani Mix Chart.pdfChart Kalyan
A Mix Chart displays historical data of numbers in a graphical or tabular form. The Kalyan Rajdhani Mix Chart specifically shows the results of a sequence of numbers over different periods.
Trusted Execution Environment for Decentralized Process MiningLucaBarbaro3
Presentation of the paper "Trusted Execution Environment for Decentralized Process Mining" given during the CAiSE 2024 Conference in Cyprus on June 7, 2024.
Fueling AI with Great Data with Airbyte WebinarZilliz
This talk will focus on how to collect data from a variety of sources, leveraging this data for RAG and other GenAI use cases, and finally charting your course to productionalization.
Programming Foundation Models with DSPy - Meetup SlidesZilliz
Prompting language models is hard, while programming language models is easy. In this talk, I will discuss the state-of-the-art framework DSPy for programming foundation models with its powerful optimizers and runtime constraint system.
Unlock the Future of Search with MongoDB Atlas_ Vector Search Unleashed.pdfMalak Abu Hammad
Discover how MongoDB Atlas and vector search technology can revolutionize your application's search capabilities. This comprehensive presentation covers:
* What is Vector Search?
* Importance and benefits of vector search
* Practical use cases across various industries
* Step-by-step implementation guide
* Live demos with code snippets
* Enhancing LLM capabilities with vector search
* Best practices and optimization strategies
Perfect for developers, AI enthusiasts, and tech leaders. Learn how to leverage MongoDB Atlas to deliver highly relevant, context-aware search results, transforming your data retrieval process. Stay ahead in tech innovation and maximize the potential of your applications.
#MongoDB #VectorSearch #AI #SemanticSearch #TechInnovation #DataScience #LLM #MachineLearning #SearchTechnology
TrustArc Webinar - 2024 Global Privacy SurveyTrustArc
How does your privacy program stack up against your peers? What challenges are privacy teams tackling and prioritizing in 2024?
In the fifth annual Global Privacy Benchmarks Survey, we asked over 1,800 global privacy professionals and business executives to share their perspectives on the current state of privacy inside and outside of their organizations. This year’s report focused on emerging areas of importance for privacy and compliance professionals, including considerations and implications of Artificial Intelligence (AI) technologies, building brand trust, and different approaches for achieving higher privacy competence scores.
See how organizational priorities and strategic approaches to data security and privacy are evolving around the globe.
This webinar will review:
- The top 10 privacy insights from the fifth annual Global Privacy Benchmarks Survey
- The top challenges for privacy leaders, practitioners, and organizations in 2024
- Key themes to consider in developing and maintaining your privacy program
Digital Marketing Trends in 2024 | Guide for Staying AheadWask
https://www.wask.co/ebooks/digital-marketing-trends-in-2024
Feeling lost in the digital marketing whirlwind of 2024? Technology is changing, consumer habits are evolving, and staying ahead of the curve feels like a never-ending pursuit. This e-book is your compass. Dive into actionable insights to handle the complexities of modern marketing. From hyper-personalization to the power of user-generated content, learn how to build long-term relationships with your audience and unlock the secrets to success in the ever-shifting digital landscape.
GraphRAG for Life Science to increase LLM accuracyTomaz Bratanic
GraphRAG for life science domain, where you retriever information from biomedical knowledge graphs using LLMs to increase the accuracy and performance of generated answers
Ocean lotus Threat actors project by John Sitima 2024 (1).pptxSitimaJohn
Ocean Lotus cyber threat actors represent a sophisticated, persistent, and politically motivated group that poses a significant risk to organizations and individuals in the Southeast Asian region. Their continuous evolution and adaptability underscore the need for robust cybersecurity measures and international cooperation to identify and mitigate the threats posed by such advanced persistent threat groups.
Let's Integrate MuleSoft RPA, COMPOSER, APM with AWS IDP along with Slackshyamraj55
Discover the seamless integration of RPA (Robotic Process Automation), COMPOSER, and APM with AWS IDP enhanced with Slack notifications. Explore how these technologies converge to streamline workflows, optimize performance, and ensure secure access, all while leveraging the power of AWS IDP and real-time communication via Slack notifications.
Let's Integrate MuleSoft RPA, COMPOSER, APM with AWS IDP along with Slack
Athens pecker 2005
1. DESIGN AND CONSTRUCTION OF THE RION ANTIRION BRIDGE
FOUNDATIONS
A. Pecker
Géodynamique et Structure, Bagneux, France
Abstract
The choice of a design concept for a bridge foundation is guided by various factors; several
of these factors are indeed of technical origin, like the environmental conditions in a broad
sense, but others non technical factors may also have a profound impact on the final design
concept. The foundations solutions adopted for the Rion Antirion bridge are described and
an attempt is made to pinpoint the major factors that have guided the final choices. The
Rion Antirion bridge is exemplar in that respect: the foundation concept combines the
simplicity of capacity design, the conceptual facility of construction and enhances the
foundation safety. The design of these foundations was a very challenging task which
required full cooperation and close interaction with all the parties involved: concessionaire,
contractor, designers and design checker.
INTRODUCTION
The Rion-Antirion bridge project is a BOT contract
granted by the Greek Government to a consortium
led by the French company Vinci Construction
(formerly Dumez-GTM). It is located in Greece, near
Patras, will constitute a fixed link between the
Peloponese and the Continent across the western
end of the gulf of Corinth and is intended to replace
an existing ferry system (Fig. 1). The solution
adopted for this bridge is a multiple spans cable
stayed bridge with four main piers; the three central
spans are 560 m long each and are extended by two
adjacent spans (one on each side) 286 m long. The
total length of the bridge, with the approach viaducts,
is approximately 2.9 kilometers (Fig. 2). The call for
tender was launched in 1992, the contract, awarded
to the consortium in 1996, took effect in December
1997. Construction started in 1998 and has been
completed in summer 2004 and opened to traffic on
the 11th
of August, five months ahead of schedule.
The bridge has to be designed for severe
environmental conditions (e.g., Teyssandier et al.
2000; Teyssandier 2002): weak alluvium deposits,
high water depth, highly seismic area, possible
occurrence of large tectonic displacements. Very
early in the design process it turned out that design
was mainly controlled by the seismic demand
imposed to the foundations.
Fig. 1: Location of the bridge
In order to alleviate potential damage to the structure
due to the above adverse conditions and to carry the
large earthquake forces brought to the foundation
(shear force of the order of 500 MN and overturning
moment of the order of 18 000 MNm for a vertical
buoyant pier weight of 750 MN), an innovative
foundation concept was finally adopted which
consists of a gravity caisson (90 m in diameter at the
sea bed level) resting on top of the reinforced natural
ground (Combault et al. 2000). The ground
reinforcement is composed of steel tubular pipes, 2
m in diameter, 20 mm thick, 25 to 30 m long driven
1
2. at a grid of 7 m x 7 m below and outside the
foundation, covering a circular area of approximately
8 000 m2
. The total number of inclusions under each
foundation is of the order of 150 to 200. In addition,
the safety of the foundation is greatly enhanced by
interposing a gravel bed layer, 2.8 m thick, on top of
the inclusions just below the foundation raft with no
structural connection between the raft and the
inclusions heads. This concept (inclusions plus
gravel layer), in addition to minimizing the hazards
related to differential settlements, enforces a
capacity design philosophy in the seismic foundation
design, (Pecker 1998).
In the following we will focus on the foundations of
the main bridge, because the foundations of the
approach viaducts (pile foundations) do not deserve
much comments.
Fig. 2: Bridge elevation
GEOLOGICAL AND GEOTECHNICAL
ENVIRONMENT
The site has been subjected to extensive offshore
soil investigations performed either from floating
barges or from a ship, controlled with a dynamic
positioning system; these investigations included
cored boreholes, static Cone Penetration Tests with
pore pressure measurements (CPTU), Standard
Penetration tests (SPT), vane tests and dilatometer
tests, seismic cone tests and sampling of intact soil
samples for laboratory testing. All the borings
reached depths ranging from 60 m to 100 m below
the sea bed. Under each of the main bridge pier
three continuous boreholes, three CPTU, two
seismic cones, one SPT/dilatometer boring have
been drilled. Approximately 300 samples have been
retrieved and subjected to advanced laboratory
testing. Based on the results of these investigations
representative soil profiles have been defined at the
locations of the main bridge piers and ranges of soil
mechanical characteristics have been derived.
The water depth in the middle of the strait reaches
65 m. The soil profile consists of weak alluvial strata
deposited in alternate layers, with individual
thickness of a few meters, of silty sands, sandy clays
and medium plasticity clays. In the top hundred
meters investigated by the soil survey, the clay, or
silty clay, layers predominate (Fig. 3). No bedrock
was encountered during the investigations and
based on geological studies and geophysical
surveys its depth is believed to be greater than
500 m.
65
m
RIO
N
ANTI
ON
65
m
65 m
RIO
N
ANTI
ON
CLAY
SILT
SAND-GRAVEL
Fig. 3: Soil profile
The mechanical characteristics of the offshore layers
are rather poor with undrained shear strengths of the
cohesive strata increasing slowly with depth from
approximately 30-50 kN/m2
at the sea bed level to
80-100 kN/m2
at 50 m depth (Fig. 4). A major
difference occurs in the cohesionless strata: some of
these layers are prone to significant pore pressure
buildup, even possibly to liquefaction, under the
design earthquake. Accordingly, the undrained
strengths of the cohesionless layers are taken equal
either to their cyclic undrained shear strengths or to
their residual strengths.
Based on the results of the laboratory one
dimensional compressibility tests and of correlations
with CPT results or with the undrained shear
strengths, a slight overconsolidation, of the order of
150 kN/m2
, of the upper strata was evidenced.
The shear wave velocities are also small, increasing
from 100-150 m/s at the ground surface to 350-
400 m/s at 100 m depth (Fig. 5).
It is worth noting that for design, as shown in Fig.4
and Fig.5, two sets of soil characteristics have been
used instead of a single set based on characteristic
values; this decision is guided by the fundamental
necessity to maintain compatibility in the whole
seismic design process: the seismic demand is
calculated assuming one set of properties
(successively lower bound and upper bound) and
the foundation capacity is checked with the
associated strengths (respectively lower bound and
upper bound); the capacity is never checked with
low properties when the forces are calculated with
high properties and vice versa. In addition, given the
large foundation dimensions, special attention has
been paid to the spatial variability of the soil
properties across anyone foundation; this variability
3. may have an impact on the differential settlement
and tilt of a pylon. Fig. 6 gives an example of the
variability of the cone point resistance across a
foundation, variability which is obviously reflected by
variability in the shear strength and compressibility
of the soil strata.
Fig. 4: Undrained shear strength
ENVIRONMENTAL CONDITIONS
The environmental conditions are defined by three
major possible events likely to occur during the
bridge life time: ship impact on a main bridge pier,
occurrence of a major earthquake in the vicinity of
the bridge, long term tectonic movements.
Ship impact
The hazard represented by this impact corresponds
to 160 000 Mg tanker hitting one pier at a speed of
16 knots (8.2 m/s). This impact induces an
horizontal shear force of 480 MN acting at 70 m
above the foundation level; at the foundation level
the
corresponding forces are: shear force of 480 MN
and overturning moment of 34 000 MNm.
Earthquake event
The bridge is located in one of the most seismic area
in Europe. In the past 35 years three earthquakes
exceeding 6.5 on the Richter scale have occurred in
the Gulf of Corinth. The 1995 Aigion earthquake
took place less than 30 km east of the site. Fig. 7
presents the epicenters of the major earthquakes felt
in the Gulf of Corinth along with the major tectonic
faults. The contract fixed for the design motion a
return period of 2 000 years. A comprehensive
seismic hazard analysis has defined the governing
event as a 7.0 surface wave magnitude earthquake
originating on the Psathopyrgos fault (shown with an
arrow in Fig. 7) only 8.5 km east of the site (circle in
Fig. 7).
Fig. 5 : Shear wave velocity
0
20
40
60
80
100
0 100 200 300 400 500 600
Shear wave velocity (m/s)
Depthbelowgroundsurface(m)
Depthbelowseabed
Distance
-60
-80
-120
40-60 600 20
65
55
45
25
15
5
35
-100
-40 -20
0
20
40
60
80
100
0 100 200 300 400 500
Undrained shear strength (kN/m2
)
Depthbelowgroundsurface(m)
Fig. 6 : Spatial variability of cone resistance
In recognition of the influence of the soil
characteristics on the ground surface motion, the
design response spectrum at the sea bed elevation
is defined from specific site response analyses
based on the actual soil characteristics and on the
design rock motion defined by the seismic hazard
analysis. The 5% damped response spectrum is
shown in Fig. 8: the peak ground acceleration is
equal to 0.5g, the plateau at 1.2 g is extending from
0.2 s to 1.1 s and at 2 s the spectral acceleration is
still high, equal to 0.62 g.
Tectonic movements
The seismic threat arises from the prehistoric drift in
the earth's crust that shifted the Peloponese away
from mainland Greece. The peninsula continues to
move away from the mainland by a few millimeters
each year. As a result the bridge must
accommodate a 2 m differential tectonic
4. displacement in any direction and between any two
piers.
Fig. 7: Locations of major earthquakes
0.00
0.25
0.50
0.75
1.00
1.25
1.50
- 1.0 2.0 3.0 4.0 5.0
Period(s)
Pseudoacceleration(g)
Fig. 8: Design ground surface response
spectrum
MAIN BRIDGE FOUNDATIONS
Very soon during the design stage it appeared that
the foundations design will be a major issue. On the
one hand, the unfavorable geotechnical conditions
with no competent layer at shallow depth, the large
water depth, typical of depths currently encountered
in offshore engineering and the high seismic
environment represent a combination of challenging
tasks. It was also realized that the earthquake
demand will govern the concept and dimensioning of
the foundations. On the other hand, the time
allowed for design turned out to be a key factor:
thanks to the contractor who decided to anticipate
the difficulties, the design studies started one year
ahead of the official effective date. Advantage was
taken of this time lapse to fully investigate alternative
foundation solutions, to develop and to validate the
innovative concept that was finally implemented.
The amount of time spent initially for the
development of the design concept was worthwhile
and resulted in a substantial saving for the
foundation. In addition, the close cooperation that
existed from the beginning within the design team
between structural and geotechnical engineers,
between the design team and the construction team
on one hand, and between the design team and the
design checker on the other hand, was a key to the
success.
Investigated foundation solutions
After a careful examination of all the environmental
factors listed above, no solution seems to dominate.
Several solutions were investigated: piled
foundation, caisson foundation, surface foundation.
Piles were quickly abandoned for two reasons: the
difficulty to realize the structural connection between
the slab and the piles in a deep water depth, and the
rather poor behavior of floating piles in seismic areas
as observed in Mexico city during the 1985
Michoacan earthquake. Caissons foundations were
hazardous due to the presence of a gravel layer at
the ground surface (Fig. 3), which may induce some
difficulties during penetration of the caisson.
Surface foundation was clearly impossible in view of
the poor foundation bearing capacity and of the high
anticipated settlements. However, it was quickly
realized that surface foundation was the only viable
alternative from a construction point of view:
construction techniques used for offshore gravity
base structures are well proven and could easily be
implemented for the Rion-Antirion bridge.
The problem posed by the poor soil conditions still
remains to be solved. Soil improvement is required
in order to ensure an adequate bearing capacity and
to limit the settlements to acceptable values for the
superstructure. Several techniques were
contemplated from soil dredging and backfilling (soil
substitution), to in situ treatment with stone columns,
grouted stone columns, lime columns. The need for
a significant high shear resistance of the improved
soil and for a good quality control of the achieved
treatment led to the use of driven steel pipes, a
technique derived from offshore engineering, to
reinforce the soil beneath the foundations. To
prevent any confusion with piles foundations, which
behave differently than steel pipes, those are named
inclusions.
5. Adopted foundation concept
In order to alleviate potential damage to the structure
due to the adverse environmental conditions and to
carry the large earthquake forces brought to the
foundation (shear force of the order of 500 MN and
overturning moment of the order of 18 000 MNm for
a vertical buoyant pier weight of 750 MN), the
innovative foundation design concept finally adopted
(Fig. 9) consists of a gravity caisson (90 m in
diameter at the sea bed level) resting on top of the
reinforced natural ground (Teyssandier 2002,
Teyssandier 2003). The ground reinforcement (Fig.
10) is composed of steel tubular pipes, 2 m in
diameter, 20 mm thick, 25 to 30 m long driven at a
grid of 7 m x 7 m below and outside the foundation
covering a circular area of approximately 8 000 m2
The total number of inclusions under each
foundation is therefore of the order of 150 to 200. In
addition, as shown below, the safety of the
foundation is greatly enhanced by interposing a
gravel bed layer, 2.8 m thick, on top of the inclusions
just below the foundation raft with no structural
connection between the raft and the inclusions
heads (Fig. 10). The reinforcement scheme is
implemented under three of the four piers: M1, M2
and M3. Under pier M4, which rests on a 20 m thick
gravel layer, soil reinforcement is not required and
the caisson rests directly on a 1 m thick ballast layer
without inclusions.
65m
90m
230m
65m
90m
230m
Fig. 9: View of one pylon of the Rion-Antirion
bridge
The concept (inclusions plus gravel layer) enforces a
capacity design philosophy in the foundation design
(Pecker 1998). The gravel layer is equivalent to the
"plastic hinge" where inelastic deformation and
energy dissipation take place and the "overstrength"
is provided by the ground reinforcement which
prevents the development of deep seated failure
mechanisms involving rotational failure modes of the
foundation. These rotational failure modes would be
very detrimental to the high rise pylon (230 m). If the
design seismic forces were exceeded the "failure"
mode would be pure sliding at the gravel-foundation
interface; this "failure mechanism" can be
accommodated by the bridge, which is designed for
much larger tectonic displacements than the
permanent seismically induced ones. The concept
is also somehow similar to a base isolation system
with a limitation of the forces transmitted to the
superstructure whenever sliding occurs.
Fig. 10: Foundation reinforcement
JUSTIFICATION OF THE FOUNDATIONS
The foundations have to be designed with respect to
static loads (dead loads, live loads and tectonic
differential movements) and with respect to dynamic
loads (ship impact and earthquake). With regards to
the static loads, the main issue is the settlements
evaluation: absolute settlement and differential
settlements inducing tilt, to which the 230 m high
pylon is very sensitive. With regards to the
earthquake loads, several problems have to be
solved: evaluation of the seismic demand, i.e. the
forces transmitted to the foundation during an
earthquake, and check of the foundation capacity,
i.e. calculation of the ultimate bearing capacity and
earthquake induced permanent displacements.
Static loads
The immediate settlement of the foundation is not a
major concern since approximately 80% of the total
permanent load (750 MN) is brought by the pier
below the deck level. More important are the
consolidation settlements of the clay strata which
induces differed settlements. The settlements are
computed with the classical one dimensional
consolidation theory but the stress distribution in the
soil is computed from a three dimensional finite
element analysis in which the inclusions are
modeled. It is found that the total load is shared
between the inclusions for approximately 35 to 45 %
6. and the soil for the remaining 55 to 65 %. The
average total settlement varies from 17 cm to 28 cm
for Piers M1 to M3. For Pier M4 the computed
settlement is much smaller, of the order of 2cm. The
figures given above are the maximum settlements
predicted before construction; they were computed
assuming the most conservative soil characteristics,
neglecting for instance the slight overconsolidation
of the upper strata. Consolidation settlements were
estimated to last for 6 to 8 months after completion
of the pier.
The differential settlements are evaluated on the
basis of the spatial variability of the compressibility
characteristics assessed from the variability of the
point cone resistances (Fig. 6). The computed
foundation tilts range from 7. 10-4
to 1.8 10-3
radians,
smaller than those that would have been computed
without inclusions: the inclusions homogenize the
soil properties in the top 25 m and transfer part of
the loads to the deeper, stiffer, strata.
0
200
400
600
800
1000
0 200 400 600 800
Fréquence (Hz)
TotalLoad(MN)
-12.0
-10.0
-8.0
-6.0
-4.0
-2.0
0.0
2.0
Elapsed time (days)
Settlement(cm)
Fig. 11: Settlement versus time – Pier M3
Although the previous figures were acceptable, it
was decided, in order to increase the safety of the
structure, to preload the pier during construction.
This preloading was achieved by filling the central
part of the cone pier (Fig. 9) with water during
construction to a total weight slightly larger than the
final pier weight. Deballasting was carried out as
construction proceeded, maintaining the total weight
approximately at its final value. The beneficial effect
of this preloading is readily apparent in Fig. 11,
which shows the recorded settlement and applied
load versus time during construction. The final
settlement amounts to 8 cm as compared to 22 cm
originally anticipated, and occurred more rapidly.
This is clearly a beneficial effect of the
overconsolidation, as back calculations have shown.
More important the foundation tilts are almost
negligible, less than 3 10-4
.
Seismic loads
The evaluation of the seismic behavior of the
foundation requires that the seismic demand and the
seismic capacity be calculated. However, as for any
seismic design, it is important to first define the
required performance of the structure. For the Rion
Antirion bridge this performance criterion was clearly
stated in the technical specifications: "The
foundation performance under seismic loading is
checked on the basis of induced displacements and
rotations being acceptable for ensuring reusability of
the bridge after the seismic event". In other words, it
is accepted that the foundation experiences
permanent displacements after a seismic event,
provided the induced displacements remain limited
and do not impede future use of the bridge. Full
advantage of this allowance was taken in the
definition of the design concept: sliding of the pier on
the gravel layer is possible (and tolerated) but
rotational mode of failures are prevented (and
forbidden).
Seismic capacity
Because of the innovative concept and therefore of
its lack of precedence in seismic areas, its
justification calls for the development of new design
tools and extensive validation. A very efficient three
stages process was implemented to this end:
• Development of design tools based on a limit
analysis theory to estimate the ultimate capacity
of the foundation system and to define the
inclusions layout: length and spacing. As any
limit analysis method, this tool cannot give any
indication on the induced displacements and
rotations.
• Verification of the final layout with a non linear
two, or three, dimensional finite element analysis.
These analyses provide non only a check of the
ultimate capacity but also the non linear stress
strain behavior of the foundation that will be
included in the structural model for the seismic
calculations of the bridge.
• Experimental verification of the design tools
developed in step 1 with centrifuge model tests.
As shown below all three approaches give results
which are within ±15% of each other, which
increases the confidence in the analyses performed
for design.
The design tools are based on the Yield Design
theory (Salençon 1983), further extended to
reinforced earth media, (de Buhan and Salençon
1990). The kinematic approach of the Yield Design
theory applied to mechanisms of the type shown in
Fig. 12, (Pecker and Salençon 1999), permits the
determination, for a wrench of forces (N vertical
force, V horizontal force and M overturning moment)
applied to the foundation, of the sets of allowable
7. loads; this set defines in the loading space
parameters a bounding surface with an equation:
( , , ) 0N V MΦ = (1)
Any set of loads located within the bounding surface
can be safely supported by the foundation, whereas
any set located outside corresponds to an unsafe
situation, at least for permanently imposed loads.
Ω
ω
B
λΒ
ε''
α µ
δ
F
Fig. 12: Kinematic mechanism
Fig. 13 presents a cross section of the bounding
surface by a plane N=constant, corresponding to the
vertical weight of one pier. Two domains are
represented in the figure: the smallest one
correspond to the soil without the inclusions, the
largest one to the soil reinforced with the inclusions.
The increase in capacity due to the inclusions is
obvious and allows the foundation to support
significantly larger loads (V and M). Furthermore,
the vertical ascending branch on the bounding
surface, on the right of the figure, corresponds to
sliding at the soil-foundation interface in the gravel
bed layer. When moving on the bounding surface
from the point (M=0, V=560 MN), sliding at the
interface is the governing failure mechanism until the
overturning moment reaches a value of
approximately 20 000 MN; for larger values of the
overturning moment, rotational mechanisms tend to
be the governing mechanisms and the maximum
allowable horizontal force decreases. The height of
the vertical segment, corresponding to a sliding
mechanism, is controlled by the inclusions layout
and can therefore be adjusted as necessary. The
design philosophy is based on that feature: for a
structure like the pylon with a response governed by
the fundamental mode, there is proportionality
between M and V, the coefficient of proportionality
being equal to the height of the center of gravity
above the foundation. When V increases the point
representative of the loads moves in the plane of
Fig. 13 along a straight line passing through the
origin, assuming that the vertical force is constant; it
eventually reaches the bounding surface defining
foundation failure.
0
5000
10000
15000
20000
25000
30000
35000
0 100 200 300 400 500 600 700
Horizontal force at foundation level (MN)
Overturningmoment(MN-m)
Fig. 13: Cross section of the bounding
surface: Doted line without inclusions; solid line with
inclusions
The inclusions layout is then determined in a way
such that this point be located on the vertical
ascending branch of the bounding surface.
The previous analysis provides the ultimate capacity
of the foundation but no information on the
displacements developed at that stage. These
displacements are calculated from a non linear finite
element analysis. Most of the calculations are
performed with a 2D model, but some additional
checks are made with a 3D model. For those
calculations, the parameters entering the non linear
elastoplastic soil constitutive model are determined
from the laboratory tests carried out on the
undisturbed soil samples; interface elements with
limiting shear resistance and zero tensile capacity
are introduced between, on one hand, each
inclusion and the soil and, on the other hand, the raft
and the soil. These models are loaded to failure
under increasing monotonic loads such that
M/V=constant (Fig. 14). Results are compared to
those obtained from the Yield Design theory in Fig.
13; a very good agreement is achieved with
differences of the order of ±12% for all the
calculations made for the project. However, it is
worth noting that the finite element analyses,
because of the large computer time demand, could
not have been used to make the preliminary design;
the Yield Design theory is, in that respect, a more
efficient tool: to establish the full cross section of the
bounding surface represented in Fig. 10 requires
only 10 to 15 minutes on a PC; a non linear finite
element analysis, i.e. a single point of the curve,
requires more than 4 hours of computing in 2D and
15 hours in 3D on a workstation with 4 parallel
processors.
This totally innovative concept, at least in seismic
areas, clearly calls for extensive theoretical analyses
and experimental validation. As sophisticated as
8. they can be, the theoretical and numerical tools do
not have the capacity for modeling all the details of
the behavior of this complex scheme during an
earthquake. Centrifuge model tests were therefore
undertaken with a three-fold objective:
• To validate the theoretical predictions of the
ultimate bearing capacity of the foundation under
monotonically increasing shear force and
overturning moment,
• To identify the failure mechanism of the
foundation under these combined loads,
• To assess the behavior of the foundation under
various cyclic load paths.
0
100
200
300
400
500
600
700
0.00 0.05 0.10 0.15 0.20 0.25 0.30
Displacement at foundation level (m)
Horizontalforce(MN)
M = 50 V
M = 30 V
0
5000
10000
15000
20000
25000
30000
0.0E+00 1.0E-03 2.0E-03 3.0E-03 4.0E-03 5.0E-03
Rotation at foundation level (rd)
Overturningmoment(MN-m)
M = 50 V
M = 30 V
Fig. 14: Finite element analyses: force-
displacement curves
Four tests have been performed in the 200 g-ton
geotechnical centrifuge at the LCPC Nantes center,
(Pecker and Garnier 1999). It is designed to carry a
2000 kg payload to 100 g accelerations, the bucket
surface is at a radius of 5.5 m and the platform has a
working space of 1.4 m by 1.1 m. All tests have
been carried out at 100 g on models at a scale of
1/100. The dimensions of the corresponding
prototype are as follows:
• radius of the circular footing: Bf = 30 m,
• inclusions length and diameter: L = 8.5 m and
B=0.67 m,
• Wall thickness t = 6.7 mm (steel), Stiffness EI =
158 MN.m2
,
• Thickness of the ballast layer: 1.2 m.
The soil material has been sampled at the location of
pier N17 of the Antirion approach viaduct and sent to
the laboratory where it was reconsolidated prior to
the tests to reproduce the in situ shear strength
profile. The loads applied to the foundation consist
of a constant vertical force and of a cyclic shear
force and overturning moment; at the end of the
tests the specimens are loaded to failure under
monotonically increasing loads with a constant ratio
M/V. The main findings of the test are summarized
in Fig. 15 which compares the theoretical predictions
of the failure loads (class A prediction according to
the terminology introduced by Whitman) to the
measured failure loads. Disregarding the
preliminary tests that were carried out with another
equipment (CESTA centrifuge in Bordeaux), all four
tests yield values within ±15% of the predictions
obtained with the Yield Design theory.
The centrifuge tests not only provide the ultimate
loads but also valuable information on factors that
either could not be easily apprehended by the
analysis or need experimental verification. Of
primary interest is the fact that, even under several
cycles of loading at amplitudes representing 75% of
the failure load, the foundation system does not
degrade; no tendency for increased displacement
with the number of cycles is noted. The equivalent
damping ratios calculated from the hysteresis loops
recorded during the tests are significant with values
as high as 20%; it is interesting to note that these
values have been confirmed by numerical analyses
and can be attributed, to a large extent, to the
presence of the inclusions (Dobry et al. 2003).
Finally, a more quantitative information is given by
the failure mechanisms observed in the centrifuge,
which compare favorably either with the
mechanisms assumed a priori in the Yield Design
theory (Fig. 12), or with those computed from the
non linear finite element analyses (Fig. 16).
The approach explained above takes care of the
justification of the inclusions. Another important
issue is the behavior of the gravel bed layer; a
fundamental requirement for this layer is to exhibit a
well defined and controlled shear resistance, which
defines the ultimate capacity for the sliding modes of
failure. This requirement can only be achieved if no
pore pressure buildup occurs in the layer during the
earthquake; the development of any excess pore
pressure means that the shear resistance is
governed by the soil undrained cyclic shear strength,
a parameter highly variable and difficult to assess
with accuracy. The grain size distribution of the
gravel bed layer (10-80 mm) is therefore chosen to
ensure a fully drained behavior (Pecker and al
2001). Furthermore, the friction coefficient between
the slab and the gravel has been measured on site
with friction tests using a concrete block pushed on
top of the gravel bed layer; a rather stable value
(0.53 to 0.57) has been measured for that
coefficient.
9. 0
20
40
60
80
100
120
0 50 100
Measured horizontal failure load (MN)
Computedhorizontalfailureload(MN)
Fig. 15: Computed versus measured failure
loads in the centrifuge tests:
Preliminary tests (diamonds); final tests (triangles)
Fig. 16: Failure mechanisms: centrifuge test
(upper left), FE analysis (lower right)
Seismic demand
For the seismic analyses it is mandatory to take into
account soil structure interaction, which is obviously
significant given the soft soil conditions and large
pier mass. In the state of practice, the action of the
underlying soil is represented with the so-called
impedance functions, the simplified version of them
consisting, for each degree of freedom, of constant
springs and dashpots. In the calculation of these
springs and dashpots the soil modulus is calibrated
on the free field strains, neglecting any further non
linearity developed in the vicinity of the foundation
(Pecker and Pender 2000). Such an approach may
be inadequate because it implicitly assumes that the
forces generated on the foundation are independent
of its yielding. Therefore there is some
inconsistency in checking the foundation capacity for
those forces. Recent studies, (e.g., Paoluci 1997,
Pedretti 1998, Cremer et al. 2001, Cremer et al.
2002), throw some light on this assumption and
clearly show that close to the ultimate capacity it is
no longer valid. This is typically the situation faced
for the foundation of the Rion-Antirion bridge.
Therefore it was decided to implement a more
realistic approach which closely reflects the physics
of the interaction. Since numerous parametric
studies are necessary for the design, a dynamic non
linear soil finite element model is not the proper tool.
In the same spirit as the impedance functions, the
action of the soil (and inclusions) below the
foundation slab is represented by what is called a
macro-element (Cremer and al 2001, Cremer and al
2002). The concept of macro-element is based on a
partitioning of the soil foundation into (Fig. 17):
• A near field in which all the non linearities linked
to the interaction between the soil, the inclusions
and the slab are lumped; these non linearities are
geometrical ones (sliding, uplift of the foundation)
or material ones (soil yielding). The energy
dissipation is of hysteretic nature.
• A far field in which the non linearities are
governed by the propagation of the seismic
waves; the energy dissipation is essentially of a
viscous type.
In its more complete form the macro-element model
couples all the degrees of freedom (vertical
displacement, horizontal displacement and rotation)
(Cremer et al. 2001). For the design studies of the
bridge a simplified version of it, in which the degrees
of freedom are uncoupled, is used. Conceptually
this element can be represented by the rheological
model shown at the bottom of Fig.17; it consists of
an assemblage of springs and Coulomb sliders for
the near field and of a spring and a dashpot for the
far field. One such model is connected in each
direction at the base of the structural model; the
parameters defining the rheological model are
calibrated on the monotonic force-displacement and
moment-rotation curves computed from the non
linear static finite element analyses (Fig. 14). For
unloading-reloading a Masing type behavior is
assumed; the validity of this assumption is backed
up by the results of the centrifuge tests (Pecker and
Garnier 1999) and of cyclic finite element analyses
(Dobry et al. 2003). The adequacy of the macro-
element to correctly account for the complex non
linear soil structure interaction is checked by
comparison with few dynamic non linear finite
element analyses including a spatial modeling of the
foundation soil and inclusions.
Fig. 18 compares the overturning moment at the
foundation elevation calculated with both models; a
very good agreement is achieved, not only in terms
of amplitudes but also in terms of phases.
10. A
λ4
λ3λ2λ1C0
FoundationNear FieldFar Field
K0
K1 K2 K3
NEAR FIELD
M
FAR FIELD
θ
K0 C0
Fig. 17: Macro element for soil structure
interaction
This model has been subsequently used by the
structural design team for all the seismic analyses of
the bridge. It allows for the calculations of the cyclic
and permanent earthquake displacements; Fig.19
shows the displacement of the foundation center
(bottom) and the variation of the forces in the (N-V)
plane (top); sliding in the gravel bed layer occurs at
those time steps when tanV N φ= .
-16000
-8000
0
8000
16000
0 5 10 15 20 25 30 35 40 45 50
Time (s)
Overturningmoment(MN-m)
Simplified model
Finite element
Fig. 18: Time history of foundation
overturning moment
CONSTRUCTION METHODS
The construction methods for the foundations,
described in details by Teyssandier (2002 and
2003), are those commonly used for the construction
of offshore concrete gravity base structures:
• construction of the foundation footings in a dry
dock up to a height of 15 m in order to provide
sufficient buoyancy;
• towing and mooring of these footings at a wet
dock site;
• construction of the conical part of the foundations
at the wet dock site;
• towing and immersion of the foundations at its
final position.
However some features of this project make the
construction process of its foundations quite
exceptional.
The dry dock has been established near the site. It
was 200 m long, 100 m wide, 14m deep, and could
accommodate the simultaneous construction of two
foundations. It had an unusual closure system: the
first foundation was built behind the protection of a
dyke, but once towed out, the second foundation,
the construction of which had already started, was
floated to the front place and used as a dock gate.
Verticalforce(MN)
1200
800
400
0 2000 6004000
0
V
H = V tgφ
Horizontal force (MN)
tanV N φ=
Uy(m)
-- 0.15
-- 0.10
-- 0.05
00.05
00.10
00.15
-0.35 -0.25 -0.15 -0.05
Ux
y
Ux (m)
Fig. 19: Time history of foundation
displacement
Top – variation of forces in the (N-V) plane
Bottom - displacement of foundation center
Dredging the seabed, driving of inclusions, placing
and levelling the gravel layer on the top, with a water
depth reaching 65 m, was a major marine operation
which necessitated special equipment and
procedures. In fact, a tension-leg barge has been
custom-made, based on the well known concept of
tension-leg platforms but used for the first time for
movable equipment.
11. This concept was based on active vertical
anchorage to dead weights lying on the seabed (Fig.
20). The tension in these vertical anchor lines was
adjusted in order to give the required stability to the
barge with respect to sea movements and loads
handled by the crane fixed on its deck. By increasing
the tension in the anchor lines, the buoyancy of the
barge allowed the anchor weights to be lifted from
the seabed, then the barge, including its weights,
could be floated away to a new position.
As already stated, once completed the foundations
are towed then sunk at their final position.
Compartments created in the footings by the radial
beams can be used to control tilt by differential
ballasting. Then the foundations are filled with water
to accelerate settlements. This pre-loading was
maintained during pier shaft and pier head
construction, thus allowing a correction for potential
differential settlements before erecting pylons.
The deck of the main bridge is erected using the
balance cantilever technique, with prefabricated
deck elements 12 m long comprising also their
concrete slab (another unusual feature).
Fig. 20: Tension-leg barge
ACKNOWLEDGMENTS
The development of this original foundation concept
was made possible thanks to the full cooperation
between all the parties involved in the project: the
Concessionaire (Gefyra SA), the Contractor (Gefyra
Kinopraxia), the Design JV and the Design Checker
(Buckland & Taylor Ltd). The author is indebted to
Mr. Teyssandier from Gefyra SA, Mr De Maublanc
and Morand from Gefyra Kinopraxia, Mr Tourtois
from the Design JV and Dr. Taylor for their long term
collaboration and confidence. He also wishes to
specially thank Dr Peck, Dr. Dobry and Dr Gohl,
consultants to the Checker, for their invaluable
contribution through their constant willingness to
help him clarify and develop the concept.
More information on the project can be found on the
web site www.gefyra.gr.
REFERENCES
Combault, J., Morand, P., Pecker, A. (2000).
"Structural response of the Rion Antirion Bridge."
Proc. of the 12th World Conf. on Earthq. Eng.,
Auckland, Australia.
Cremer, C., Pecker, A., Davenne L. (2001). "Cyclic
macro-element for soil structure interaction - Material
and geometrical non linearities." Num. Methods in
Geomech., 25, 1257-1284.
Cremer, C., Pecker, A., Davenne L. (2002).
"Modelling of non linear dynamic behaviour of a
shallow strip foundation with macro-element." J. of
Earthq. Eng., 6(2), 175-212.
de Buhan, P., Salençon, J. (1990). "Yield strength of
reinforced soils as anisotropic media." in Yielding,
Damage and Failure of Anisotropic Solids; EGF5,
Mechanical Engineering Publications, London.
Dobry, T., Abdoun, T., O'Rourke, T.D., Goh, S.H.
(2003). "Single piles in lateral spreads: Field bending
moment evaluation". J. Geotech. and Geoenv. Eng.,
ASCE, 129(110), 879-889.
Dobry, R., Pecker, A., Mavroeidis, G., Zeghal, M.,
Gohl, B., Yang, D. (2003). "Damping/Global Energy
Balance in FE Model of Bridge Foundation Lateral
Response." J. of Soil Dynamics and Earthq. Eng.,
23(6), 483-495.
Paolucci, R. (1997). "Simplified evaluation of
earthquake induced permanent displacement of
shallow foundations." J. of Earthq. Eng., 1(3), 563-
579.
Pecker, A. (1998). "Capacity Design Principles For
Shallow Foundations In Seismic Areas." Proc. 11th
European. Conf.. on Earthq. Eng., A.A. Balkema
Publishing.
Pecker, A., Salençon, J. (1999). "Ground
Reinforcement In Seismic Area." Proc. of the XI
Panamerican Conf. on Soil Mech. and Geotech.
Eng., Iguasu, 799-808.
12. Pecker, A., Garnier, J. (1999). "Use of Centrifuge
Tests for the Validation of Innovative Concepts in
Foundation Engineering." Proc. 2nd
Int. Conf. on
Earthq. Geotech. Eng., Lisbon, 433-439.
Pecker, A., Pender, M.J. (2000). "Earthquake
resistant design of foundations : new construction."
GeoEng2000 , 1, 313-332.
Pecker, A., Prevost, J.H., Dormieux, L. (2001).
"Analysis of pore pressure generation and
dissipation in cohesionless materials during seismic
loading." J. of Earthq. Eng., 5(4), 441-464.
Pedretti, S. (1998). "Nonlinear seismic soil-
foundation interaction: analysis and modeling
method." PhD Thesis, Politecnico di Milano, Milan.
Salençon, J. (1983). "Introduction to the yield
design theory." European Journal of Mechanics
A/Solids 9(5), 477-500.
Teyssandier, J.P., Combault, J., Pecker, A. (2000).
"Rion Antirion: le pont qui défie les séismes." La
Recherche, 334, 42-46.
Teyssandier, J.P. (2002). "Corinthian Crossing." Civil
Engineering, 72(10), 43 -49.
Teyssandier, J.P. (2003). "The Rion-Antirion bridge,
Design and construction." ACI International
Conference on Seismic Bridge Design and Retrofit.
La Jolla, California.