EDEN - Acumentrics Comparison Chart
•Download as DOC, PDF•
1 like•413 views
The document summarizes the Acumentrics 5 kW SOFC system. It provides details on the system specifications including gas and electric power outputs. It also lists references from previous field trials. The technology uses Acumentrics tubular stacks with partial oxidation reforming without recirculation. Advantages include experience, low cost per kW, and development of power systems up to MW size. Disadvantages include requiring maintenance training and replacement of stacks only by technicians from the US. The system is suitable for demonstration projects and 31 units have been delivered with over 3,000 hours of field experience. Cost estimates are provided for delivery, start-up, monitoring, operation, maintenance, and warranty terms.
Report
Share
Report
Share
Recommended
Revisiting the Model Parameters of an Existing System Using the Photovoltaic ...
Presented at the IEEE Photovoltaic Specialists Conference (PVSC) in June 2015. The software PVSAT is introduced and the impacts of parameter true-up are discussed. This version of the slides was produced at the same time Amplify Energy was spun off from Yingli Americas (just prior to public announcement of the spin-off).
Gas turbine advisors review of a 9 e.03 ccgt power plant
we were asked to study the feasibility of a 9E.03 CCGT application for a potential project in Myanmar. In short : doesnt makes sense. No redundancy and high heat rate due to limited gas volume.
65 sutterlueti using_advanced_pv_and_bo_s_modelling_and_algorithms_to_optimiz...
65 sutterlueti using_advanced_pv_and_bo_s_modelling_and_algorithms_to_optimiz...Sandia National Laboratories: Energy & Climate: Renewables
Using advanced PV and BoS modeling and algorithms to optimize the performance of large scale utility applicationsArticle_Power Plant_ISO 50001
1) The document discusses the need to consider additional factors when establishing baselines and measuring performance for power plants under the ISO 50001 energy management standard.
2) These factors include things like fuel availability, scheduling, ambient conditions, planned/forced outages that can impact a plant's loading and efficiency.
3) The document uses a case study of a gas-fired power plant to show how unaccounted factors led to its reported performance deteriorating against its baseline, though the plant operator argued external factors lowered its loading.
Ect dielsel-engine-whr-gmr
This document discusses a waste heat recovery turbine project at a 200 MW diesel engine power plant in Chennai, India. The plant recovers heat from engine exhaust using a heat recovery steam generator and steam turbine to generate 600 kW of additional power. Installed in 2011, the turbine saves $300,000 per year in energy costs and will save $4.5 million over its 15-year lifetime. The project has an payback period of less than 2 years and provides environmental benefits like reduced carbon emissions.
Ect captive-power
This document discusses the installation of a 425 kW energy conservation turbine (ECT) at the captive power plant of Ballarpur Industries Limited, one of the largest paper producers in the region. The ECT was installed in parallel with the pressure reducing valve upstream of the deaerator to generate power from steam throttling. Over its expected 15 year lifetime, the ECT is projected to save $3.4 million in capital costs with a payback period of less than 2 years, while also improving process efficiency and reducing the plant's carbon footprint and energy consumption.
2014 PV Performance Modeling Workshop: Optimizing PV Designs with HelioScope:...
2014 PV Performance Modeling Workshop: Optimizing PV Designs with HelioScope:...Sandia National Laboratories: Energy & Climate: Renewables
2014 PV Performance Modeling Workshop: Optimizing PV Designs with HelioScope: Paul Gibbs, Folsom Labs12 02 lima - gccsi - why invest in ccs - final
SaskPower has been involved in carbon capture and storage (CCS) initiatives due to regulations requiring emissions reductions from coal and natural gas power units. SaskPower has implemented CCS at its Boundary Dam power station unit 3, capturing over 100,000 tonnes of CO2 since start-up in 2014. This project captures 80-90% of CO2 from the unit and demonstrates CCS technology on a commercial scale, with potential for worldwide application to reduce CO2 emissions from power generation.
Recommended
Revisiting the Model Parameters of an Existing System Using the Photovoltaic ...
Presented at the IEEE Photovoltaic Specialists Conference (PVSC) in June 2015. The software PVSAT is introduced and the impacts of parameter true-up are discussed. This version of the slides was produced at the same time Amplify Energy was spun off from Yingli Americas (just prior to public announcement of the spin-off).
Gas turbine advisors review of a 9 e.03 ccgt power plant
we were asked to study the feasibility of a 9E.03 CCGT application for a potential project in Myanmar. In short : doesnt makes sense. No redundancy and high heat rate due to limited gas volume.
65 sutterlueti using_advanced_pv_and_bo_s_modelling_and_algorithms_to_optimiz...
65 sutterlueti using_advanced_pv_and_bo_s_modelling_and_algorithms_to_optimiz...Sandia National Laboratories: Energy & Climate: Renewables
Using advanced PV and BoS modeling and algorithms to optimize the performance of large scale utility applicationsArticle_Power Plant_ISO 50001
1) The document discusses the need to consider additional factors when establishing baselines and measuring performance for power plants under the ISO 50001 energy management standard.
2) These factors include things like fuel availability, scheduling, ambient conditions, planned/forced outages that can impact a plant's loading and efficiency.
3) The document uses a case study of a gas-fired power plant to show how unaccounted factors led to its reported performance deteriorating against its baseline, though the plant operator argued external factors lowered its loading.
Ect dielsel-engine-whr-gmr
This document discusses a waste heat recovery turbine project at a 200 MW diesel engine power plant in Chennai, India. The plant recovers heat from engine exhaust using a heat recovery steam generator and steam turbine to generate 600 kW of additional power. Installed in 2011, the turbine saves $300,000 per year in energy costs and will save $4.5 million over its 15-year lifetime. The project has an payback period of less than 2 years and provides environmental benefits like reduced carbon emissions.
Ect captive-power
This document discusses the installation of a 425 kW energy conservation turbine (ECT) at the captive power plant of Ballarpur Industries Limited, one of the largest paper producers in the region. The ECT was installed in parallel with the pressure reducing valve upstream of the deaerator to generate power from steam throttling. Over its expected 15 year lifetime, the ECT is projected to save $3.4 million in capital costs with a payback period of less than 2 years, while also improving process efficiency and reducing the plant's carbon footprint and energy consumption.
2014 PV Performance Modeling Workshop: Optimizing PV Designs with HelioScope:...
2014 PV Performance Modeling Workshop: Optimizing PV Designs with HelioScope:...Sandia National Laboratories: Energy & Climate: Renewables
2014 PV Performance Modeling Workshop: Optimizing PV Designs with HelioScope: Paul Gibbs, Folsom Labs12 02 lima - gccsi - why invest in ccs - final
SaskPower has been involved in carbon capture and storage (CCS) initiatives due to regulations requiring emissions reductions from coal and natural gas power units. SaskPower has implemented CCS at its Boundary Dam power station unit 3, capturing over 100,000 tonnes of CO2 since start-up in 2014. This project captures 80-90% of CO2 from the unit and demonstrates CCS technology on a commercial scale, with potential for worldwide application to reduce CO2 emissions from power generation.
Energy conservation sachivalaya part 2
This is second part of the presentation on Energy conservation efforts made in secretariat building in Gandhinagar. Presentation was made on Energy Conservation Day at Gujarat State Center, The Institution of Engineers (India) at Ahmedabad.
Energy management 101
This document discusses basics of energy management for schools, including ways to reduce rising utility costs and carbon footprint. It provides information on obtaining energy data, converting voltage to kilowatts, calculating heating and cooling degree days, and sizing buildings. Methods outlined for managing energy use include controlling demand, optimizing HVAC equipment and set points, collecting data, and utilizing backup generation and variable frequency drives. The document also discusses lighting improvements and alternative energy options.
COOP training-Bokhari
The document provides information about a refinery including:
- It started operating in 1984 as a joint venture and now processes 400,000 BPD of crude oil.
- Its main product yields are gasoline, diesel, jet fuel, and fuel oil.
- It has technical, operations, maintenance, and financial departments.
- Case studies examine crude distillation unit stream flows over 10 years and calculate heat exchanger fouling rates to predict cleaning needs.
- An experience overview discusses the refinery's induction program and a heat exchanger bundle replacement and testing project.
Energy analysis using computer aided design
A quick presentation from my 3rd year project in college based on a BIM model, utilizing the model as a tool to gauge the energy and carbon footprint for a large residential area.
T ptsch brochure_didsolit
This document summarizes a project to develop and implement decentralized solar energy systems for cooling and heating public buildings in Mediterranean countries. The system would consist of parabolic trough solar collectors with a power rating of 20-60 kW that provides high temperature oil to an absorption chiller. It would have sensors for tracking, temperatures, wind speed and PLC controls. The goal is to identify small scale solar systems that are modular, efficient, easily integrated into buildings and have low operation and maintenance costs.
2014 PV Performance Modeling Workshop: Optimization strategies with Pvsyst fo...
2014 PV Performance Modeling Workshop: Optimization strategies with Pvsyst fo...Sandia National Laboratories: Energy & Climate: Renewables
2014 PV Performance Modeling Workshop: Optimization strategies with Pvsyst for large scale PV installations: Bruno Wittmer, PvsystKK Wind Solutions presentation on Control System Retrofit
1) A presentation was given on retrofitting control systems in wind turbines. Retrofitting control systems can improve power output, availability, and reduce operation and maintenance costs.
2) A case study was presented on retrofitting the control systems on 50 Bonus 1.3MW turbines. The retrofit improved the power curve, replaced pitch and main controllers, and added remote monitoring capabilities.
3) The retrofit paid for itself in less than 3 years through increased revenue from higher output and reduced operation costs from improvements like fewer yaw motor replacements. Retrofitting control systems was shown to be more profitable than other wind turbine upgrades.
What does wind really cost? Modeling Wind Resources In AURORAxmp.
Ray Bliven, Power Rates Manager for Bonneville Power Administration, describes the practical pitfalls of developing wind resources, how to model wind generation through the EPIS AURORAxmp modeling software, and discusses the issues surrounding wind generation.
New Wave EXECUITIVE PRESENTATION KHPP
The document proposes an investment project to generate hydrokinetic power using a system that combines pressurized water and air to create mechanical movement and inertia to power generators, providing pollution-free electricity continuously. It describes 5MW, 40MW and 100MW power plant systems that require small plots of land and use neodymium magnet generators to produce electricity at competitive costs with quick returns on investment. Contact information is provided for Jean M Lacroix, the CEO, regarding additional details on the hydrokinetic power technology.
REC 275w peak energy 60 cell
REC Peak Energy Series solar panels are high-performance panels designed for reliability. They combine quality materials and manufacturing with a durable design to produce high power output under all sunlight conditions. REC uses leading standards in design and production to ensure uncompromising quality and reliability. The panels come with a 10-year product warranty and 25-year linear power output warranty.
IBM Spectrum Control creating a heat map with Cognos
The document provides steps to create a heat map showing processor utilization for nodes in an SVC storage system over time. It explains how to generate the heat map report within the IBM Spectrum Control (TPC) Cognos tool by selecting the appropriate metrics, creating sections by storage system and node, and then configuring cell colors based on utilization ranges. The final heat map report gives a visual overview of processor usage across nodes and clusters in the SVC.
Optimisation of Balance of System (BOS) for Solar Projects
The document discusses trends in the balance of systems (BOS) costs for solar photovoltaic projects. Key points include:
- BOS costs, which include components beyond the solar panels, have decreased from around 35% to 30% of total project costs from 2013-2017 due to innovations like larger block sizes and more efficient inverters and mounting systems.
- Increasing solar panel efficiency from 10% to 17% over the last 10 years has also reduced BOS costs by allowing the use of fewer panels and less cabling/land for the same energy output.
REC Peak Energy 275W
REC Peak Energy Series solar panels are high-performance panels designed for reliability. They combine quality materials and manufacturing with a durable design to produce high power output under all sunlight conditions. The panels come with a 10-year product warranty and 25-year linear power output warranty.
25 ben duck_improved_prediction_of_site_spectral_impact
25 ben duck_improved_prediction_of_site_spectral_impactSandia National Laboratories: Energy & Climate: Renewables
This document discusses improved methods for predicting the spectral impact on PV systems based on commonly available data. It presents a modified CREST model that uses the true spectral response rather than a useful fraction to better account for variations due to cloudy conditions. Evaluation shows this modified CREST-WUF model significantly outperforms existing models in predicting daily spectral impact factors for different module types. While this approach captures more variation than previous models, further work is still needed to fully characterize the relationship between site properties and spectral offset to enable general predictions of spectral impact.Cost Components in a MW Scale Solar Power Project
This document discusses the key cost components and considerations for a 25 MW scale solar power project in India. It outlines that the major cost components are solar modules (60% of costs), inverters (8% of costs), mounting structures (5% of costs), and balance of system equipment (12% of costs). Land costs account for 2% of total costs. The document then provides a breakdown of estimated costs per MW for different project components and scales from 25MW to 100MW, showing economies of scale. It also discusses factors that can impact execution costs and ways to optimize costs through rate contracts, backward integration, and prior land acquisition.
B4 - Theistareykir Geothermal Power Plant An update on successful project
Valur Knútsson, Chief project manager, Landsvirkjun
Iceland Geothermal Conference 2018 - Breaking the Barriers
24 - 27 April, 2018, Harpa, Reykjavík
Solar power sector: Technology, BoS, Pre Feasbility and phase of project dev...
This document provides a summary of key aspects of solar power projects including technology, costs and project development phases. Some key points from the document include:
- The basic schematic and components of a solar power system are described, including how solar energy is converted to DC and then AC current for transmission to the grid.
- Key solar technologies like polycrystalline and thin film solar modules are discussed as well as manufacturing processes. Historical and projected future increases to solar cell efficiencies are presented.
- The cost structures and trends for solar modules and balance of system components are analyzed, showing modules now account for 65% of project costs on average. Factors driving further cost reductions are also outlined.
-
ERU CEP.pptx
This document summarizes the methodology used to analyze the cooling load inside a truck cabin and size a photovoltaic system to meet the load. HAP software was used to calculate the monthly cooling loads based on weather data for Karachi, Pakistan from April to September. PVsyst software then sized the solar panels, batteries, and other system components needed to meet the cooling load. The maximum cooling load of 8.8 MBH occurred in the southwest direction in September. A 16 panel, 23 battery system with a total cost of 118,161.5 rupees was designed, which would pay for itself in about 2.2 years based on estimated annual savings.
Opportunities in the Wind Industry Supply Chain
Ports-to-Plains Energy Summit
Omni Interlocken Resort
Broomfield, CO
April 7, 2011
The Ports-to-Plains Corridor runs through the middle of North America’s wind corridor. Learn about the issues affecting this growing industry throughout the region.
Fall Final Presentation
This document summarizes a student project to develop an alternative automotive air conditioning system using thermoelectric materials. It presents the problem statement, key factors for the design including functional performance, human factors, economic considerations, and pollution limits. It describes testing a lab model and prototypes in vehicles. The system uses thermoelectric modules, an aluminum mounting block, cooling pipes, reservoir, electric pump, and wiring harness. Data shows it can remove 60-75 BTUs of heat. An economic analysis and recommendations are provided. In conclusion, it is a good alternative for cars without AC currently but thermoelectrics are only suitable for mild cooling and too large for most vehicles.
Modern farmers mini-design_project
This document discusses a proposed vertical farming system that integrates three technologies - Tesla Powerpacks, Thermenex temperature control system, and Climate Manager sensors - to improve upon an existing vertical farm system. The proposed system is estimated to have a total operating cost of $11,165, setup cost of $8,060,517, and production capacity of 650 tons per year of leafy greens using a 54,000 square foot facility. Testing of the proposed system would involve analytical modeling, building a smaller scaled prototype, and validating that performance meets requirements for key metrics like production capacity, energy consumption, and profitability.
Drivers and Barriers in the current CSP market
This webinar will provide a general view of drivers and barriers for CSP development, with a particular focus on the structure of the CSP Value Chain. From a technical point of view, the main key performances will be reviewed for the different technologies.
More Related Content
What's hot
Energy conservation sachivalaya part 2
This is second part of the presentation on Energy conservation efforts made in secretariat building in Gandhinagar. Presentation was made on Energy Conservation Day at Gujarat State Center, The Institution of Engineers (India) at Ahmedabad.
Energy management 101
This document discusses basics of energy management for schools, including ways to reduce rising utility costs and carbon footprint. It provides information on obtaining energy data, converting voltage to kilowatts, calculating heating and cooling degree days, and sizing buildings. Methods outlined for managing energy use include controlling demand, optimizing HVAC equipment and set points, collecting data, and utilizing backup generation and variable frequency drives. The document also discusses lighting improvements and alternative energy options.
COOP training-Bokhari
The document provides information about a refinery including:
- It started operating in 1984 as a joint venture and now processes 400,000 BPD of crude oil.
- Its main product yields are gasoline, diesel, jet fuel, and fuel oil.
- It has technical, operations, maintenance, and financial departments.
- Case studies examine crude distillation unit stream flows over 10 years and calculate heat exchanger fouling rates to predict cleaning needs.
- An experience overview discusses the refinery's induction program and a heat exchanger bundle replacement and testing project.
Energy analysis using computer aided design
A quick presentation from my 3rd year project in college based on a BIM model, utilizing the model as a tool to gauge the energy and carbon footprint for a large residential area.
T ptsch brochure_didsolit
This document summarizes a project to develop and implement decentralized solar energy systems for cooling and heating public buildings in Mediterranean countries. The system would consist of parabolic trough solar collectors with a power rating of 20-60 kW that provides high temperature oil to an absorption chiller. It would have sensors for tracking, temperatures, wind speed and PLC controls. The goal is to identify small scale solar systems that are modular, efficient, easily integrated into buildings and have low operation and maintenance costs.
2014 PV Performance Modeling Workshop: Optimization strategies with Pvsyst fo...
2014 PV Performance Modeling Workshop: Optimization strategies with Pvsyst fo...Sandia National Laboratories: Energy & Climate: Renewables
2014 PV Performance Modeling Workshop: Optimization strategies with Pvsyst for large scale PV installations: Bruno Wittmer, PvsystKK Wind Solutions presentation on Control System Retrofit
1) A presentation was given on retrofitting control systems in wind turbines. Retrofitting control systems can improve power output, availability, and reduce operation and maintenance costs.
2) A case study was presented on retrofitting the control systems on 50 Bonus 1.3MW turbines. The retrofit improved the power curve, replaced pitch and main controllers, and added remote monitoring capabilities.
3) The retrofit paid for itself in less than 3 years through increased revenue from higher output and reduced operation costs from improvements like fewer yaw motor replacements. Retrofitting control systems was shown to be more profitable than other wind turbine upgrades.
What does wind really cost? Modeling Wind Resources In AURORAxmp.
Ray Bliven, Power Rates Manager for Bonneville Power Administration, describes the practical pitfalls of developing wind resources, how to model wind generation through the EPIS AURORAxmp modeling software, and discusses the issues surrounding wind generation.
New Wave EXECUITIVE PRESENTATION KHPP
The document proposes an investment project to generate hydrokinetic power using a system that combines pressurized water and air to create mechanical movement and inertia to power generators, providing pollution-free electricity continuously. It describes 5MW, 40MW and 100MW power plant systems that require small plots of land and use neodymium magnet generators to produce electricity at competitive costs with quick returns on investment. Contact information is provided for Jean M Lacroix, the CEO, regarding additional details on the hydrokinetic power technology.
REC 275w peak energy 60 cell
REC Peak Energy Series solar panels are high-performance panels designed for reliability. They combine quality materials and manufacturing with a durable design to produce high power output under all sunlight conditions. REC uses leading standards in design and production to ensure uncompromising quality and reliability. The panels come with a 10-year product warranty and 25-year linear power output warranty.
IBM Spectrum Control creating a heat map with Cognos
The document provides steps to create a heat map showing processor utilization for nodes in an SVC storage system over time. It explains how to generate the heat map report within the IBM Spectrum Control (TPC) Cognos tool by selecting the appropriate metrics, creating sections by storage system and node, and then configuring cell colors based on utilization ranges. The final heat map report gives a visual overview of processor usage across nodes and clusters in the SVC.
Optimisation of Balance of System (BOS) for Solar Projects
The document discusses trends in the balance of systems (BOS) costs for solar photovoltaic projects. Key points include:
- BOS costs, which include components beyond the solar panels, have decreased from around 35% to 30% of total project costs from 2013-2017 due to innovations like larger block sizes and more efficient inverters and mounting systems.
- Increasing solar panel efficiency from 10% to 17% over the last 10 years has also reduced BOS costs by allowing the use of fewer panels and less cabling/land for the same energy output.
REC Peak Energy 275W
REC Peak Energy Series solar panels are high-performance panels designed for reliability. They combine quality materials and manufacturing with a durable design to produce high power output under all sunlight conditions. The panels come with a 10-year product warranty and 25-year linear power output warranty.
25 ben duck_improved_prediction_of_site_spectral_impact
25 ben duck_improved_prediction_of_site_spectral_impactSandia National Laboratories: Energy & Climate: Renewables
This document discusses improved methods for predicting the spectral impact on PV systems based on commonly available data. It presents a modified CREST model that uses the true spectral response rather than a useful fraction to better account for variations due to cloudy conditions. Evaluation shows this modified CREST-WUF model significantly outperforms existing models in predicting daily spectral impact factors for different module types. While this approach captures more variation than previous models, further work is still needed to fully characterize the relationship between site properties and spectral offset to enable general predictions of spectral impact.Cost Components in a MW Scale Solar Power Project
This document discusses the key cost components and considerations for a 25 MW scale solar power project in India. It outlines that the major cost components are solar modules (60% of costs), inverters (8% of costs), mounting structures (5% of costs), and balance of system equipment (12% of costs). Land costs account for 2% of total costs. The document then provides a breakdown of estimated costs per MW for different project components and scales from 25MW to 100MW, showing economies of scale. It also discusses factors that can impact execution costs and ways to optimize costs through rate contracts, backward integration, and prior land acquisition.
B4 - Theistareykir Geothermal Power Plant An update on successful project
Valur Knútsson, Chief project manager, Landsvirkjun
Iceland Geothermal Conference 2018 - Breaking the Barriers
24 - 27 April, 2018, Harpa, Reykjavík
Solar power sector: Technology, BoS, Pre Feasbility and phase of project dev...
This document provides a summary of key aspects of solar power projects including technology, costs and project development phases. Some key points from the document include:
- The basic schematic and components of a solar power system are described, including how solar energy is converted to DC and then AC current for transmission to the grid.
- Key solar technologies like polycrystalline and thin film solar modules are discussed as well as manufacturing processes. Historical and projected future increases to solar cell efficiencies are presented.
- The cost structures and trends for solar modules and balance of system components are analyzed, showing modules now account for 65% of project costs on average. Factors driving further cost reductions are also outlined.
-
ERU CEP.pptx
This document summarizes the methodology used to analyze the cooling load inside a truck cabin and size a photovoltaic system to meet the load. HAP software was used to calculate the monthly cooling loads based on weather data for Karachi, Pakistan from April to September. PVsyst software then sized the solar panels, batteries, and other system components needed to meet the cooling load. The maximum cooling load of 8.8 MBH occurred in the southwest direction in September. A 16 panel, 23 battery system with a total cost of 118,161.5 rupees was designed, which would pay for itself in about 2.2 years based on estimated annual savings.
Opportunities in the Wind Industry Supply Chain
Ports-to-Plains Energy Summit
Omni Interlocken Resort
Broomfield, CO
April 7, 2011
The Ports-to-Plains Corridor runs through the middle of North America’s wind corridor. Learn about the issues affecting this growing industry throughout the region.
Fall Final Presentation
This document summarizes a student project to develop an alternative automotive air conditioning system using thermoelectric materials. It presents the problem statement, key factors for the design including functional performance, human factors, economic considerations, and pollution limits. It describes testing a lab model and prototypes in vehicles. The system uses thermoelectric modules, an aluminum mounting block, cooling pipes, reservoir, electric pump, and wiring harness. Data shows it can remove 60-75 BTUs of heat. An economic analysis and recommendations are provided. In conclusion, it is a good alternative for cars without AC currently but thermoelectrics are only suitable for mild cooling and too large for most vehicles.
What's hot (20)
2014 PV Performance Modeling Workshop: Optimization strategies with Pvsyst fo...
2014 PV Performance Modeling Workshop: Optimization strategies with Pvsyst fo...
KK Wind Solutions presentation on Control System Retrofit
KK Wind Solutions presentation on Control System Retrofit
What does wind really cost? Modeling Wind Resources In AURORAxmp.
What does wind really cost? Modeling Wind Resources In AURORAxmp.
IBM Spectrum Control creating a heat map with Cognos
IBM Spectrum Control creating a heat map with Cognos
Optimisation of Balance of System (BOS) for Solar Projects
Optimisation of Balance of System (BOS) for Solar Projects
25 ben duck_improved_prediction_of_site_spectral_impact
25 ben duck_improved_prediction_of_site_spectral_impact
B4 - Theistareykir Geothermal Power Plant An update on successful project
B4 - Theistareykir Geothermal Power Plant An update on successful project
Solar power sector: Technology, BoS, Pre Feasbility and phase of project dev...
Solar power sector: Technology, BoS, Pre Feasbility and phase of project dev...
Similar to EDEN - Acumentrics Comparison Chart
Modern farmers mini-design_project
This document discusses a proposed vertical farming system that integrates three technologies - Tesla Powerpacks, Thermenex temperature control system, and Climate Manager sensors - to improve upon an existing vertical farm system. The proposed system is estimated to have a total operating cost of $11,165, setup cost of $8,060,517, and production capacity of 650 tons per year of leafy greens using a 54,000 square foot facility. Testing of the proposed system would involve analytical modeling, building a smaller scaled prototype, and validating that performance meets requirements for key metrics like production capacity, energy consumption, and profitability.
Drivers and Barriers in the current CSP market
This webinar will provide a general view of drivers and barriers for CSP development, with a particular focus on the structure of the CSP Value Chain. From a technical point of view, the main key performances will be reviewed for the different technologies.
Slide 1_Arpita
The document provides energy usage and portfolio information for the Prescott Service Center building. It details the building size, energy sources, current energy consumption, improvement opportunities in building envelop, solar power, and lighting. Implementing improvements in building envelop, installing solar panels, and switching to LED lighting can reduce annual energy consumption by over 342,000 kWh and save over $37,000 per year while achieving payback periods of less than 10 years for the investments.
shagufta-final review
This document provides a summary of a research project on modeling the degradation of solar photovoltaic modules over time. It examines modules installed at two solar power plants in India - a 1 MW plant on an ash dyke and a 1 MW canal top plant. Testing showed canal top modules had lower temperatures and higher performance. The project developed loss models and found polycrystalline modules degraded 1.73-3.89% annually at one plant and 0.17-1.95% at the other. Regular cleaning can avoid a 1.61% efficiency loss from soiling. The models matched simulated results within a few percent.
Thesis Presentation
Flexible international exchanges: a possible solution for large – scale wind power integration within the future power system
Solar 101 - Franklin 8/20/14
The 'solar 101' presentation made at the Solar Challenge meeting held in Franklin, MA on Aug 20, 2014
Design and Simulation of Divided Wall Column - Design of the Column
The document summarizes the design and simulation of a divided wall column for separating reformate into benzene, toluene, and p-xylene. It includes the reformate composition, literature review on divided wall columns, material and energy balances, minimum number of trays calculation, Aspen simulation, materials selection, and a cost analysis. The divided wall column consists of a prefractionator with 13 trays separating to a side draw and a main column with 9 + 10 trays achieving high purity products within specifications. The simulation matches the material balances with less than 1% difference. The total capital cost is estimated at $1.67 billion with a payback period of 2.8 years.
IEA DSM Task 17: Integration of DSM, DG, RES and ES – Outcome of Phase 1 and ...
IEA DSM Task 17: Integration of DSM, DG, RES and ES – Outcome of Phase 1 and ...IEA DSM Implementing Agreement (IA)
Presented by René Kamphuis, TNO NL and Matthias Stifter, AIT Energy Department, Austria at the IEA DSM workshop in Lucerne, Switzerland on 16 October 2013.Mayfair homes-lg-smart-net-zero-energy-home-concept-compressed
Net zero energy program is energy sustainable home building program by the Canadian government. Mayfair home also building energy efficient home for their clients in Toronto.
A practical approach to pharmaceutical HVAC energy reduction
This document outlines strategies for reducing energy use in pharmaceutical HVAC systems. It identifies common areas with high energy savings potential, such as reducing air change rates and implementing night/weekend setbacks. Barriers to energy reduction like lack of funding and QA approval are discussed. The presentation recommends hosting team-based "energy kaizens" to identify opportunities and gain stakeholder buy-in. Case studies show projects at pharmaceutical plants that cut HVAC energy use up to 66% by optimizing air flow and implementing variable speed controls.
Renewable Energy Laboratory group project.pdf
This report presents an evaluation of the feasibility of a hybrid system combining
solar and biomass energy sources. The evaluation is conducted using HOMER
Pro software, a powerful tool for analyzing and optimizing hybrid power systems.
The main objectives of this study are to assess the technical and economic
viability of the proposed hybrid system, as well as its potential environmental
benefits. The results obtained from HOMER Pro simulations provide valuable
insights into the system's performance, cost-effectiveness, and sustainability,
enabling informed decision-making for implementing hybrid energy systems.
The depletion of conventional energy sources and the need for sustainable energy
alternatives have led to the exploration of hybrid energy systems. This report
focuses on evaluating the feasibility of a hybrid solar and biomass system, which
combines two renewable energy sources to provide reliable and clean power
generation. The HOMER Pro software is utilized to simulate and analyze the
system's technical and economic aspects, including component sizing, energy
production, and cost optimization
Stephen O'Rourke | PV Status and Pathways
The document discusses the solar photovoltaic (PV) industry and projections for cost reductions and growth. It finds that:
1) The levelized cost of electricity from solar PV is becoming competitive with electricity from the grid and other sources as costs continue to decline for PV technologies like cadmium telluride and copper indium gallium selenide.
2) By the next 6 years, the costs of different PV technologies are projected to converge, with thin film technologies like cadmium telluride maintaining an advantage over crystalline silicon at the module level.
3) Periodic oversupply of solar modules is inevitable as capacity growth outpaces demand, which will put downward pressure on prices.
Cuf vs pr
This document discusses the difference between CUF (Capacity Utilization Factor) and PR (Performance Ratio) as metrics for evaluating the performance of solar PV systems. CUF compares actual output to theoretical maximum output without considering external factors like weather, while PR takes these factors into account. PR is considered a better metric as it provides insights into how external conditions impact performance and allows for quality control. The benefits of PR over CUF for developers, investors and EPCs are that PR enables comparison of plant output to what could be achieved given site conditions, early identification of performance issues, and limits liability to only factors within direct control.
CUF vs PR
This document discusses the difference between CUF (Capacity Utilization Factor) and PR (Performance Ratio) as metrics for evaluating the performance of solar PV systems. CUF compares actual output to theoretical maximum output without considering external factors like weather, while PR takes these factors into account. PR is considered a better metric as it provides insights into how external conditions impact performance and allows for quality control. The benefits of PR over CUF for developers, investors and EPCs are that PR enables comparison of plant output to what could be achieved given site conditions, early identification of performance issues, and limits liability to only factors within direct control.
Poster Board_v8
The document presents a proposal for the Electron Garden on the Green (EGG) project at Western Carolina University. The objectives are to raise awareness of renewable energy on campus through an educational solar energy project that stays within a $65,000 budget. A team of 4 students and their mentor propose a 10kW solar photovoltaic system using 280W solar panels and an overloaded inverter to increase efficiency. Installation of the system is estimated to eliminate 5 tons of annual CO2 emissions and pay for itself within 39 years through energy cost savings.
Dns Smartcool Telecom
The document introduces the Energy Savings Module (ESM) and ESM ECO3, energy saving devices developed by Smartcool Technology to reduce energy consumption in air conditioning and refrigeration systems. The ESM and ECO3 utilize proprietary software and control algorithms to optimize compressor run times, achieving energy savings averaging 20% without impacting equipment performance or warranties. Case studies on installations in China, Australia, and the Philippines demonstrate annual energy savings ranging from 8,395 to 121,224 kWh.
Energy Storage: New Capabilities for the Electric Grid – The Tehachapi Energy...
The Tehachapi Energy Storage Project (TSP) is a 32 megawatt-hour battery energy storage system located in California that was jointly funded by Southern California Edison and the US Department of Energy. The project tested the battery storage system for 13 grid support applications. Initial testing showed the system could discharge 32 megawatt-hours over 4 hours as required and had an average round-trip efficiency of 90.6% during continuous cycling. However, the project faced challenges including replacing power conversion system transformers after one failed due to an unmet design requirement.
A sample of shoppers was selected and asked questions regarding co.docx
A sample of shoppers was selected and asked questions regarding consumer behavior. One of the questions asked was "Do you enjoy shopping for clothing?" Information regarding the responses is below:
· Total Responses: 500
· Males: 136 responded "yes" and 104 responded "no"
· Females: 224 responded "yes" and 36 responded "no"
Construct a contingency table summarizing the above results and answer the following questions:
1. What is the probability a shopper likes to shop for clothing?
2. Given a shopper is male, what is the probability the shopper likes to shop for clothing?
3. Given a shopper is male, what is the probability the shopper does not like to shop for clothing?
4. Given a shopper is female, what is the probability a shopper does not like to shop?
Renewable Energy 28 (2003) 873–886
www.elsevier.com/locate/renene
Technical and economical evaluation of solar
thermal power generation
Theocharis Tsoutsosa,∗, Vasilis Gekasb, Katerina Marketakib
a Centre for Renewable Energy Sources (CRES), 19th km Marathon Avenue, 19009 Pikermi, Greece
b Department of Environmental Engineering, Technical University of Crete, Crete, Greece
Received 23 July 2002; accepted 24 July 2002
Abstract
This article presents a feasibilty on a solar power system based on the Stirling dish (SD)
technology, reviews and compares the available Stirling engines in the perspective of a solar
Stirling system.
The system is evaluated, as a parameter to alleviate the energy system of the Cretan island
while taking care of the CO2 emissions. In the results a sensitivity analysis was implemented,
as well as a comparison with conventional power systems.
In the long-term, solar thermal power stations based on a SD can become a competitive
option on the electricity market, if a concerted programme capable of building the forces of
industry, finance, insurance and other decision makers will support the market extension for
this promising technology.
2002 Elsevier Science Ltd. All rights reserved.
Keywords: Technical and economical evaluation; Solar electricity generation; Solar thermal power; Stir-
ling engine
1. Introduction
The electrical generating demand has increased in the island of Crete due to the
economic growth during recent years. The rate of this increase becomes dramatical
during the summer. Conventional fossil fuel plants generate the electricity and this
∗ Corresponding author. Tel.:+30-1603-9900; fax:+30-1603-9904.
E-mail address: [email protected] (T. Tsoutsos).
0960-1481/03/$ - see front matter 2002 Elsevier Science Ltd. All rights reserved.
PII: S 0 9 6 0 -1 4 8 1 ( 0 2 ) 0 0 1 5 2 - 0
874 T. Tsoutsos et al. / Renewable Energy 28 (2003) 873–886
energy production cost is very high (Table 1); this cost can be higher in other Greek
islands [1].
The power generation should be increased over the next years in order to satisfy
the power demand. The new power plants should be environmentally since there
already exist some conventional foss.
Q Plus
The document provides technical specifications for the Q.PLUS-G3 270-280 solar photovoltaic module from Q CELLS. It summarizes the module's electrical characteristics under standard and normal operating conditions, performance warranty details, mechanical specifications, temperature coefficients, and certifications. The module features Q CELLS' Q.ANTUM cell technology for high performance even under low light conditions. It has a 12-year product warranty and 25-year linear performance warranty.
NREL_Poster_DCrouse
This study analyzed reducing electrical loads in idling long-haul trucks through improved cab insulation and orientation. Simulations of various cab configurations in 161 US cities found:
1) Facing north during rest periods can reduce annual cooling loads up to 26% while increasing heating loads up to 11%.
2) The most insulated cab configuration reduced annual cooling loads up to 55% in western cities and 40% in eastern cities, while reducing heating loads up to 35% in northern areas and 26% in southern areas.
3) This optimally insulated configuration required only around 10 kWh of battery power annually, allowing trucks to eliminate idling solely for air conditioning.
Similar to EDEN - Acumentrics Comparison Chart (20)
Design and Simulation of Divided Wall Column - Design of the Column
Design and Simulation of Divided Wall Column - Design of the Column
IEA DSM Task 17: Integration of DSM, DG, RES and ES – Outcome of Phase 1 and ...
IEA DSM Task 17: Integration of DSM, DG, RES and ES – Outcome of Phase 1 and ...
Mayfair homes-lg-smart-net-zero-energy-home-concept-compressed
Mayfair homes-lg-smart-net-zero-energy-home-concept-compressed
A practical approach to pharmaceutical HVAC energy reduction
A practical approach to pharmaceutical HVAC energy reduction
Energy Storage: New Capabilities for the Electric Grid – The Tehachapi Energy...
Energy Storage: New Capabilities for the Electric Grid – The Tehachapi Energy...
A sample of shoppers was selected and asked questions regarding co.docx
A sample of shoppers was selected and asked questions regarding co.docx
More from h2portugal
Lisbon Statement On Hydrogen
The Lisbon Statement on Hydrogen and Clean Energies proposes policies and actions to promote hydrogen as a clean energy source and transition to a hydrogen economy. It recommends that governments (1) boost implementation of hydrogen technologies, (2) balance reducing carbon emissions with funding research on hydrogen, and (3) establish university departments focused on energy to educate and conduct research. Adopting these policies could help assure a carbon-free energy future and competitive low-carbon economy through collaboration between industry, research, and new university programs.
Weto H2 2050 Com Europeia Jan07[1]
This document presents projections for global energy development and CO2 emissions from 2006 to 2050 made using the POLES energy-economic model. It considers a reference case with moderate climate policies and a carbon constraint case with more stringent CO2 reduction targets. A third case explores the potential role of hydrogen.
Key findings include:
- In the reference case, global CO2 emissions continue rising strongly due to energy demand growth in developing nations.
- The carbon constraint case requires advanced low-carbon technologies and behavioral changes to achieve over 50% reduction in global CO2 emissions by 2050 compared to 1990 levels.
- Hydrogen produced from low-carbon sources could enable deep decarbonization of transport and other hard-
Final Programme Hypothesisviii.Doc[1]
This document provides the programme for the Hypothesis VIII conference taking place from April 1-3, 2009 at the Hotel Corinthia in Lisbon, Portugal. The programme includes opening sessions, plenary lectures on hydrogen energy systems and metallic to complex hydrides. It also lists parallel sessions on topics like hydrogen production and storage, fuel cells, national/international projects, and mobility applications. The programme includes presentations, poster sessions, and a closing session with chairpersons from Portugal and the USA.
Workshop Ap2 H2 Conclusoes
Resumo das sessões temáticas do Workshop ECONOMIA DO HIDROGÉNIO, UM DESAFIO PARA PORTUGAL (Novembro 2008)
EDEN - Tarefa E 3.7 Purificacao
Este relatório descreve a tecnologia de purificação de hidrogênio por adsorção por oscilação de pressão (PSA). O PSA é um processo versátil para separação e purificação de misturas gasosas que envolve a adsorção seletiva de impurezas em um adsorvente sob alta pressão e a dessorção das mesmas sob baixa pressão. O relatório discute as vantagens, aplicações, parâmetros de otimização, adsorventes e processos PSA comerciais para a purificação de hidrogênio.
EDEN - Tarefa E3 6 Termolise
Este relatório descreve diferentes métodos de termólise para produzir hidrogénio a partir da água, incluindo decomposição direta a altas temperaturas, decomposição catalítica usando zeólitos, e ciclos termoquímicos que usam temperaturas mais baixas. Analisa os desafios técnicos e económicos de cada método e conclui que os ciclos termoquímicos são a abordagem mais promissora.
EDEN - Scoping Report Eden V1
This document provides an overview of the methodology for PPS6 EDEN activity 1 on the impact analysis of integrating hydrogen technologies into the Portuguese energy system. The analysis will cover 2020-2050, examining transportation and stationary applications of hydrogen in Portugal. Four scenarios will be examined that combine two learning curves (high and moderate) with two penetration rates (high and moderate) for hydrogen technologies. Key inputs to the analysis, like transportation demand projections and heating demands, are obtained from other modeling exercises and policy documents. The analysis will be performed using the TIMES modeling framework.
EDEN - Regulamento Senergia
Este documento descreve o regulamento de um concurso sobre sistemas sustentáveis de energia. O objetivo é estimular a comunidade a procurar novos modelos de produção e uso de energia limpa, com foco em hidrogênio. Podem participar equipes de estudantes e pessoas individuais. Serão premiados os três melhores trabalhos com base em critérios como originalidade, estratégia de transição e aplicabilidade.
EDEN - Reciclagem 57 Pps2 26 04 2007
1) O documento discute um projeto de demonstração para instalar uma pilha de combustível de 5 kW alimentada a biogás de aterro sanitário.
2) Serão entregues relatórios em junho sobre o estado da arte, pré-qualificação de fornecedores e especificações técnicas.
3) A reunião define as tarefas dos parceiros no projeto e agenda a próxima reunião.
EDEN - Portugal Vision 28 05 07
This document provides a vision for developing hydrogen energy in Portugal from 2020 to 2050. It outlines general energy challenges and policy goals for Portugal. Over time, hydrogen demand is expected to increase and be met through various production methods. In the early phase to 2020, small-scale production like electrolysis and gasification will provide hydrogen primarily for transportation. From 2020-2030, production will expand through larger electrolysis and gasification facilities to meet growing demand. After 2030, massive hydrogen production is envisioned using various domestic and imported resources to fuel transportation and heat buildings via a growing pipeline network and refueling stations.
EDEN - Pps2 26 04 2007
O documento descreve um projeto (PPS2) que tem como objetivo promover a transferência de tecnologia de pilhas de combustível para empresas portuguesas através da instalação e operação de uma pilha de combustível de óxido sólido (SOFC) de 5 kW alimentada a biogás. O projeto inclui análise do estado da arte, pré-qualificação de fornecedores, instalação da demonstração e avaliação de oportunidades futuras.
EDEN - Pps6 Eden Project Description
This document provides an overview of the tasks and timeline for the PPS6 EDEN project. The project aims to develop a roadmap and action plan for Portugal's transition to a hydrogen economy. Key tasks include developing energy scenarios and a long-term vision, analyzing pathways and impacts through modeling, assessing infrastructure needs and niche markets, and synthesizing results into a roadmap and action plan. The work is divided into three phases with workshops, meetings, and deliverables scheduled throughout 2007-2008 to engage stakeholders and document findings. Quantitative modeling will analyze economic, social, and environmental impacts while qualitative work will examine challenges, opportunities, and necessary actors. The vision and roadmap development process is meant to be iterative, with modeling and analysis
EDEN -Projectoverview
The document outlines the agenda and objectives of the Second Workshop PPS6 EDEN project in Lisbon, Portugal. The project aims to create a roadmap for integrating hydrogen into Portugal's energy system through stakeholder engagement. The workshop will focus on refining an initial vision for hydrogen's role, and receiving feedback on preliminary impact, transition and synthesis analyses to develop the final roadmap and action plan. The document provides background on hydrogen technologies, the project methodology, and a draft vision that outlines increasing roles for hydrogen production, distribution and use through 2020-2050.
EDEN - Minuta 2workshop
O documento apresenta a agenda do segundo workshop do projeto EDEN sobre a introdução do hidrogénio em Portugal. A agenda inclui sessões sobre os impactos tecnológicos e ambientais da introdução do hidrogénio, as oportunidades e desafios, e as infraestruturas necessárias. Os resultados preliminares indicam que a produção de hidrogénio dependerá principalmente de gás natural e biomassa, e que a introdução de veículos movidos a hidrogénio pode reduzir significativamente as emissões de gases com efeito de estufa dos transport
EDEN - Kcam
- Apresentação da Metodologia KCAM ("Key Changes and Actor Mapping") para análise qualitativa de dados;
- KCAM identifica as principais barreiras ("key changes") e mapeia os atores envolvidos na implementação de sistemas de hidrogénio;
- Validar dados recolhidos com os participantes do workshop.
EDEN - Lucis Project
The document summarizes the Lucis/Demtec project which aims to demonstrate the use of hydrogen fuel cells for energy applications in Portugal. Specifically, it will validate the reliability of PEM fuel cells for practical uses, evaluate their advantages over conventional solutions, and assess the economic, social and logistical impacts of their wider adoption. Two demonstration projects are described: using fuel cells for backup power for communications systems and to power traffic lights in Torres Vedras. The technology uses involves PEM fuel cells powered by hydrogen produced from renewable sources to cleanly generate electricity.
EDEN - Formularioinscricao10
Este documento é um formulário de inscrição para um concurso de sistemas sustentáveis de energia. Ele solicita informações sobre a candidatura, incluindo o nome do projeto, detalhes da instituição envolvida e descrições dos membros da equipe, como seus nomes, escolas, contatos e endereços.
Eden Pps 2
Esta tarefa analisou a informação disponível sobre os diferentes tipos de células de combustível e modelos comercializados. Caracterizou os tipos PEMFC, DMFC, AFC, PAFC, MCFC e SOFC, e levantou informações técnicas e comerciais disponibilizadas por fornecedores sobre produtos PEMFC, SOFC, AFC, PAFC e MCFC. Concluiu que as PEMFC e SOFC são as tecnologias mais maduras, enquanto AFC, PAFC e MCFC ainda requerem melhorias para aplicações móveis e
Eden Pps6 Workshop Agenda
Este documento fornece a agenda para um workshop sobre o projeto EDEN PPS6 que irá discutir cenários e taxas de penetração do hidrogênio em Portugal, analisar cadeias de abastecimento de hidrogênio e apresentar o projeto EDEN PPS6.
More from h2portugal (20)
Recently uploaded
Building Your Employer Brand with Social Media
Presented at The Global HR Summit, 6th June 2024
In this keynote, Luan Wise will provide invaluable insights to elevate your employer brand on social media platforms including LinkedIn, Facebook, Instagram, X (formerly Twitter) and TikTok. You'll learn how compelling content can authentically showcase your company culture, values, and employee experiences to support your talent acquisition and retention objectives. Additionally, you'll understand the power of employee advocacy to amplify reach and engagement – helping to position your organization as an employer of choice in today's competitive talent landscape.
Income Tax exemption for Start up : Section 80 IAC
A presentation on the concept of Exemption of Profits of Start ups from Income Tax
Business storytelling: key ingredients to a story
Storytelling is an incredibly valuable tool to share data and information. To get the most impact from stories there are a number of key ingredients. These are based on science and human nature. Using these elements in a story you can deliver information impactfully, ensure action and drive change.
ModelingMarketingStrategiesMKS.CollumbiaUniversitypdf
Implicitly or explicitly all competing businesses employ a strategy to select a mix
of marketing resources. Formulating such competitive strategies fundamentally
involves recognizing relationships between elements of the marketing mix (e.g.,
price and product quality), as well as assessing competitive and market conditions
(i.e., industry structure in the language of economics).
Top mailing list providers in the USA.pptx
Discover the top mailing list providers in the USA, offering targeted lists, segmentation, and analytics to optimize your marketing campaigns and drive engagement.
2024-6-01-IMPACTSilver-Corp-Presentation.pdf
IMPACT Silver is a pure silver zinc producer with over $260 million in revenue since 2008 and a large 100% owned 210km Mexico land package - 2024 catalysts includes new 14% grade zinc Plomosas mine and 20,000m of fully funded exploration drilling.
How MJ Global Leads the Packaging Industry.pdf
MJ Global's success in staying ahead of the curve in the packaging industry is a testament to its dedication to innovation, sustainability, and customer-centricity. By embracing technological advancements, leading in eco-friendly solutions, collaborating with industry leaders, and adapting to evolving consumer preferences, MJ Global continues to set new standards in the packaging sector.
2022 Vintage Roman Numerals Men Rings
Discover timeless style with the 2022 Vintage Roman Numerals Men's Ring. Crafted from premium stainless steel, this 6mm wide ring embodies elegance and durability. Perfect as a gift, it seamlessly blends classic Roman numeral detailing with modern sophistication, making it an ideal accessory for any occasion.
https://rb.gy/usj1a2
Taurus Zodiac Sign: Unveiling the Traits, Dates, and Horoscope Insights of th...
Dive into the steadfast world of the Taurus Zodiac Sign. Discover the grounded, stable, and logical nature of Taurus individuals, and explore their key personality traits, important dates, and horoscope insights. Learn how the determination and patience of the Taurus sign make them the rock-steady achievers and anchors of the zodiac.
Creative Web Design Company in Singapore
At Techbox Square, in Singapore, we're not just creative web designers and developers, we're the driving force behind your brand identity. Contact us today.
Structural Design Process: Step-by-Step Guide for Buildings
The structural design process is explained: Follow our step-by-step guide to understand building design intricacies and ensure structural integrity. Learn how to build wonderful buildings with the help of our detailed information. Learn how to create structures with durability and reliability and also gain insights on ways of managing structures.
一比一原版新西兰奥塔哥大学毕业证（otago毕业证）如何办理
一模一样【微信：A575476】【新西兰奥塔哥大学毕业证（otago毕业证）成绩单Offer】【微信：A575476】（留信学历认证永久存档查询）采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
【业务选择办理准则】
一、工作未确定，回国需先给父母、亲戚朋友看下文凭的情况，办理一份就读学校的毕业证【微信：A575476】文凭即可
二、回国进私企、外企、自己做生意的情况，这些单位是不查询毕业证真伪的，而且国内没有渠道去查询国外文凭的真假，也不需要提供真实教育部认证。鉴于此，办理一份毕业证【微信：A575476】即可
三、进国企，银行，事业单位，考公务员等等，这些单位是必需要提供真实教育部认证的，办理教育部认证所需资料众多且烦琐，所有材料您都必须提供原件，我们凭借丰富的经验，快捷的绿色通道帮您快速整合材料，让您少走弯路。
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
→ 【关于价格问题（保证一手价格）
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
选择实体注册公司办理，更放心，更安全！我们的承诺：可来公司面谈，可签订合同，会陪同客户一起到教育部认证窗口递交认证材料，客户在教育部官方认证查询网站查询到认证通过结果后付款，不成功不收费！
Industrial Tech SW: Category Renewal and Creation
Every industrial revolution has created a new set of categories and a new set of players.
Multiple new technologies have emerged, but Samsara and C3.ai are only two companies which have gone public so far.
Manufacturing startups constitute the largest pipeline share of unicorns and IPO candidates in the SF Bay Area, and software startups dominate in Germany.
Mastering B2B Payments Webinar from BlueSnap
B2B payments are rapidly changing. Find out the 5 key questions you need to be asking yourself to be sure you are mastering B2B payments today. Learn more at www.BlueSnap.com.
Understanding User Needs and Satisfying Them
https://www.productmanagementtoday.com/frs/26903918/understanding-user-needs-and-satisfying-them
We know we want to create products which our customers find to be valuable. Whether we label it as customer-centric or product-led depends on how long we've been doing product management. There are three challenges we face when doing this. The obvious challenge is figuring out what our users need; the non-obvious challenges are in creating a shared understanding of those needs and in sensing if what we're doing is meeting those needs.
In this webinar, we won't focus on the research methods for discovering user-needs. We will focus on synthesis of the needs we discover, communication and alignment tools, and how we operationalize addressing those needs.
Industry expert Scott Sehlhorst will:
• Introduce a taxonomy for user goals with real world examples
• Present the Onion Diagram, a tool for contextualizing task-level goals
• Illustrate how customer journey maps capture activity-level and task-level goals
• Demonstrate the best approach to selection and prioritization of user-goals to address
• Highlight the crucial benchmarks, observable changes, in ensuring fulfillment of customer needs
Organizational Change Leadership Agile Tour Geneve 2024
Organizational Change Leadership at Agile Tour Geneve 2024
Recently uploaded (20)
Income Tax exemption for Start up : Section 80 IAC
Income Tax exemption for Start up : Section 80 IAC
ModelingMarketingStrategiesMKS.CollumbiaUniversitypdf
ModelingMarketingStrategiesMKS.CollumbiaUniversitypdf
Taurus Zodiac Sign: Unveiling the Traits, Dates, and Horoscope Insights of th...
Taurus Zodiac Sign: Unveiling the Traits, Dates, and Horoscope Insights of th...
Structural Design Process: Step-by-Step Guide for Buildings
Structural Design Process: Step-by-Step Guide for Buildings
The Influence of Marketing Strategy and Market Competition on Business Perfor...
The Influence of Marketing Strategy and Market Competition on Business Perfor...
Organizational Change Leadership Agile Tour Geneve 2024
Organizational Change Leadership Agile Tour Geneve 2024
EDEN - Acumentrics Comparison Chart
- 1. ACUMENTRICS 5 KW System Sstem description: Gas supply 0,84 Nm3/h NG (8.5kW) Electric power DC 3.5kW AC 3kW (not grid connected!!!) Heat recovery 3kW Efficiency (on ) Electrical 34% Overall 70% Technology Stack Acumentrics (tubular, non pressurized, POX reforming without recirculation) System Acumentrics References (field trials) Dr. Dennis Witmer Director, Arctic Energy Technology Development Laboratory (AETDL) Tel: 1-907-474-7082 Email: ffdew@uaf.edu James Buckley President, Energy Alternatives Mobile: 1-907-227-7191 Email: jimbuckley@gci.net Daniel West (suggested contact) ELCO-MTS Groupy Tel: 49 (0) 7471 187 427 Email: Daniel.west@de.elco.net State of art Product development Future market UPS, power generation, residential, military (several kW) Gary Allen Luis Leyda teqma,s.l. leyda@teqma.com Apdo. 116. 08810 Sant Pere de Ribes (Barcelona) tf.- 93 896 4852 fax.- 93 896 4272 639 385601 leyda@aiqs.es TECHNICAL ADVICE Technology Advantages: - Large experince - Inherent strength and tolerance to rapid temperature change - Lowest cost per kW - System development for system up to MW - POX reforming without recirculation, no operating problems with the high CO2 in the form of carbon (Steam reforming and recirculation option for the end of this year) - Inverter and other parts of the BOP were also developed by Acumentrics Disadvantages: - Maintenance; training for client. Replacement of the stack, only technician from US Experience SOFC systems 31 units delivered to the field, 16 for 2007 Field Demonstrations operating now for over 3.000 hours (cells proven at 14.000 hours)
- 2. Experience with biogas Little experience in operating on biogas. Some adjustments can be made to run the system on a fuel different from natural gas. System suitable for demo yes ITEM COST / TIME INCLUDED NOT INCLUDED DELIVERY COST EVALUATION System US$210.000 Freight rate Freight charges and other shipping costs shall be paid by Buyer. Shipping of Equipment returned to Acumentrics shall be at Buyer's expense. The risk of loss or damage to Equipment in transit shall be upon Buyer. Insurances Delivery Time Q3 2007 Terms of payment Either (a) 50% pre-pay and 50% NET 30 upon delivery with Acumentrics credit approval OR (b) C.O.D. OPERATION COSTS EVALUATION Start-up US$10.500 Also commissioning Travel & living expenses Monitoring US$2.500/month minimum 6 months Operation costs Operating costs can be determined based on local fuel costs. Maintenance Estimate only: US $5000/yr. Warranty 6 months or 1.000 operating hours or 25 thermal cycles Only covers faulty parts Replacement parts and warranty labor After-sales service (logistics) System support provided by Acumentrics Corp. and represented by TEQMA, Spain.