This document provides product information for the TD 145 dry pre-assembled cable termination for outdoor use. It can be used for fixed connections and in installations with high creepage currents. The termination meets IEC 60840 standards and contains a prefabricated termination, top bolt, and other components. It has a minimum creepage distance of 4650mm, fulfilling Pollution Class IV requirements. The pre-assembled termination reduces installation time and can be installed horizontally or vertically without on-site filling.

1. Product information, Kabeldon cable accessories, December 2014
Dry pre-assembled dry cable termination, outdoor
TD 145
Use
For installations in which the cable termination is to be used
as a fixed connection point and in installations where there is
a risk of very high continuous creepage currents.
Standard
Meets the requirements of:
− IEC 60840
Design
TD 145 contains of: a prefabricated cable termination, top
bolt and bolt clamp in the top fitting and also cable clamp and
earth clamp.
The cable termination consists of a composite insulator with
integrated base part, stress cone, support pipe and dry
electricl insulating silicone compound.
Both the support pipe and the cable clamp are made of fiber-glass
reinforced polyester that provides insulated installation.
The field control component is a premolded stress cone.
The termination has a minimum creepage distance of
4650 mm, which means it fulfills Pollution class IV according
to IEC 60815-3.
A bolt clamp for the cable conductor and a top bolt is inclu-ded
in the kit.
Installation
The termination comes pre-assembled from the factory which
remarkably reduces installation time after cable preparation.
Installation can be made horizontally or vertically. No filling
of insulating medium at site.
When ordering, please state the following data:
− Diameter across prepared insulation
− Conductor cross section
− Screen, cross section and type
− Outer diameter of cable
− If optical fibers in screen
− Diameter and material of the top bolt, Cu or Al for connec-ting
to overhead power line
Voltage Designation Creepage
distance
Net weight
min
kV mm kg unit
145 TD 145 4650 100
Ø
XLPE-diameter Outer
sheath
top bolt
Bolt clamp
Cable clamp
Earth clamp
Premolded cable termination
Max conductor
cross section
min max max Ø
mm mm mm²
53 102 150 2500

2. Document ID: 7ABA102520
1630
For additional information please contact:
ABB AB
Kabeldon
Box 531
SE-441 15, Alingsås, Sweden
Tel: +46 322 770 00
e-mail: info.sedon@se.abb.com
www.abb.se/cableaccessories
© Copyright 2013 ABB. All rights reserved.
140 345–350
345–350
Ø 18.5
min 280
45°
Max. permissible
forces acting on the
top bolt, horizontally
and vertically: 2000 N.
Ø 40/50/54/60
~ 130
Creepage distance min 4650 mm
325
Ø 380
Installation cone
Installation cone.
RKM 145
Installation tool.
Dimensions in mm
Technical specification, applications and accessories
TD 145
Fixing to bracket
Insulated or non-insulated: four
18.5 mm holes for M16 bolts.
Opto kit
Optical fiber kit for cables with
integrated optical fibers in the
earth screen.
Inclination up to 45°.
Accessories, to be ordered separately
Designation Description
RKM 145 Installation tool
Installation cone Installation cone, see table.
Opto kit Optical fiber kit for optical fibers in the screen of the cable
JSA Earthing kit for cable with metallic sheath, e.g. lead. Not
needed if cable has only Cu wire screen.
SCK Screen connection for Al-foil radial waterproof cable. Not
needed if cable has only Cu wire screen.
Selection table for installation cone
Inner
diameter
Outer
diameter
Installation
cone
mm mm Article number
20 53 4209.2384
22 55 4209.2385
22 58 4209.2386
29 61 4209.2387
38 64 4209.2388
28 67 4209.2331
32 70 4209.2332
36 73 4209.2333
43 78 4209.2334
48 84 4209.2335
51 93 4209.2336
57 102 4209.2337
57 105 4209.2400