2 tutor pressure 1
•
2 likes•1,401 views
The document contains 8 questions about pressure and fluid mechanics concepts involving hydraulic presses, U-tube manometers, tanks, and piping systems. The questions provide diagrams of systems and ask the reader to calculate pressures, loads, depths, or pressure differentials based on given values like areas, forces, densities, and manometer readings. Sample calculations are not shown.
Report
Share
Report
Share
Download to read offline
Recommended
Midterm review
This document provides a mid-term review covering three topics: 1) energy analysis of closed systems, 2) mass and energy analysis of control volumes, and 3) the second law of thermodynamics. For the first topic, it provides examples of energy balance calculations for constant pressure processes in closed systems. For the second topic, it discusses the energy balance equation for control volumes and provides examples of its application to turbines, compressors, and throttling valves. For the third topic, it defines thermal efficiency and the coefficient of performance and discusses heat engines, refrigerators, and heat pumps.
Unit 5 Fluid Mechanics
The document discusses fluid dynamics and Bernoulli's equation. It provides:
1) Objectives of understanding measurements of fluids in motion and applying Bernoulli's equation to calculate energy in pipes, venturi meters, and orifices.
2) An explanation of Bernoulli's equation and its components of potential, pressure, and kinetic energy.
3) Examples of applying the equation to calculate discharge in a horizontal venturi meter using measurements of pressure and height differences.
Nozzle
The document discusses nozzle thermodynamics. Some key points:
1. A nozzle is a duct with varying cross-sectional area used to accelerate fluid flow through a pressure drop. Common applications include jet engines, rockets, and flow measurement.
2. Nozzle shape is determined using the steady flow energy equation. For an ideal, frictionless case the process is isentropic. Area varies to maintain constant mass flow rate.
3. The throat is the minimum cross-sectional area point. Flow is sonic at the throat for designed operating conditions. Critical pressure ratio is when sonic velocity is first reached.
4. Nozzle performance is affected by operating above or below design back pressure. Maximum
Thermo problem set no. 2
This document contains a 16 question multiple choice mechanical engineering review problem set. It covers topics including: specific weight calculations, changes in weight due to elevation, pressure and force calculations for scuba diving, determining height using barometer readings, properties of gas mixtures, heat transfer between materials, gas turbine processes, combustion calculations, and thermodynamic processes including changes in temperature, pressure, volume, entropy and heat/work.
Fluid ans t_2
This document contains 11 multi-step physics problems involving fluid mechanics concepts like pressure, viscosity, density, and fluid flow. The problems are solved with relevant equations for ideal gases, compressible fluids, laminar flow, and viscometry. Key values are calculated, such as mass, pressure, shear stress, drag force, velocity, and viscosity.
Sheet 1 pressure measurments
The document contains 7 problems involving the use of manometers and pressure calculations:
1) Calculating pressure differences using the formula for pressure as a function of depth and density.
2) Finding the pressure at the bottom of a lake using atmospheric pressure and the lake depth.
3) Calculating a pressure difference using a U-tube manometer filled with water and connected between two points in a pipe carrying air.
4) Determining the additional pressure needed to raise the liquid interface in a complicated U-tube manometer system containing two liquids of different densities.
5) Using a U-tube manometer containing mercury to determine the pressure reading of a pressure gauge, given column heights of
005 basic properties of fuels
The document provides information on the basic properties of fuel used in diesel engines, including mass density of fuel at standard and other temperatures, and heating or calorific values including higher heating value (HHV) and lower heating value (LHV). It also gives sample problems calculating engine properties like indicated power, brake power, mechanical efficiency, and thermal efficiency based on fuel consumption, heating value, temperature and other engine operating parameters.
Answers assignment 2 fluid statics-fluid mechanics
1. The document contains worked examples calculating hydrostatic forces and pressures on submerged objects of various shapes, including a ball plugging a hole, portholes on a ship, gates, and a steel pipe.
2. Key concepts covered include calculating hydrostatic pressure as a function of depth, determining buoyant forces, calculating net forces and moments, and sizing structural elements based on allowable stresses.
3. Formulas used include those for pressure, buoyancy, force, moment, stress, and thickness required for a given safety factor.
Recommended
Midterm review
This document provides a mid-term review covering three topics: 1) energy analysis of closed systems, 2) mass and energy analysis of control volumes, and 3) the second law of thermodynamics. For the first topic, it provides examples of energy balance calculations for constant pressure processes in closed systems. For the second topic, it discusses the energy balance equation for control volumes and provides examples of its application to turbines, compressors, and throttling valves. For the third topic, it defines thermal efficiency and the coefficient of performance and discusses heat engines, refrigerators, and heat pumps.
Unit 5 Fluid Mechanics
The document discusses fluid dynamics and Bernoulli's equation. It provides:
1) Objectives of understanding measurements of fluids in motion and applying Bernoulli's equation to calculate energy in pipes, venturi meters, and orifices.
2) An explanation of Bernoulli's equation and its components of potential, pressure, and kinetic energy.
3) Examples of applying the equation to calculate discharge in a horizontal venturi meter using measurements of pressure and height differences.
Nozzle
The document discusses nozzle thermodynamics. Some key points:
1. A nozzle is a duct with varying cross-sectional area used to accelerate fluid flow through a pressure drop. Common applications include jet engines, rockets, and flow measurement.
2. Nozzle shape is determined using the steady flow energy equation. For an ideal, frictionless case the process is isentropic. Area varies to maintain constant mass flow rate.
3. The throat is the minimum cross-sectional area point. Flow is sonic at the throat for designed operating conditions. Critical pressure ratio is when sonic velocity is first reached.
4. Nozzle performance is affected by operating above or below design back pressure. Maximum
Thermo problem set no. 2
This document contains a 16 question multiple choice mechanical engineering review problem set. It covers topics including: specific weight calculations, changes in weight due to elevation, pressure and force calculations for scuba diving, determining height using barometer readings, properties of gas mixtures, heat transfer between materials, gas turbine processes, combustion calculations, and thermodynamic processes including changes in temperature, pressure, volume, entropy and heat/work.
Fluid ans t_2
This document contains 11 multi-step physics problems involving fluid mechanics concepts like pressure, viscosity, density, and fluid flow. The problems are solved with relevant equations for ideal gases, compressible fluids, laminar flow, and viscometry. Key values are calculated, such as mass, pressure, shear stress, drag force, velocity, and viscosity.
Sheet 1 pressure measurments
The document contains 7 problems involving the use of manometers and pressure calculations:
1) Calculating pressure differences using the formula for pressure as a function of depth and density.
2) Finding the pressure at the bottom of a lake using atmospheric pressure and the lake depth.
3) Calculating a pressure difference using a U-tube manometer filled with water and connected between two points in a pipe carrying air.
4) Determining the additional pressure needed to raise the liquid interface in a complicated U-tube manometer system containing two liquids of different densities.
5) Using a U-tube manometer containing mercury to determine the pressure reading of a pressure gauge, given column heights of
005 basic properties of fuels
The document provides information on the basic properties of fuel used in diesel engines, including mass density of fuel at standard and other temperatures, and heating or calorific values including higher heating value (HHV) and lower heating value (LHV). It also gives sample problems calculating engine properties like indicated power, brake power, mechanical efficiency, and thermal efficiency based on fuel consumption, heating value, temperature and other engine operating parameters.
Answers assignment 2 fluid statics-fluid mechanics
1. The document contains worked examples calculating hydrostatic forces and pressures on submerged objects of various shapes, including a ball plugging a hole, portholes on a ship, gates, and a steel pipe.
2. Key concepts covered include calculating hydrostatic pressure as a function of depth, determining buoyant forces, calculating net forces and moments, and sizing structural elements based on allowable stresses.
3. Formulas used include those for pressure, buoyancy, force, moment, stress, and thickness required for a given safety factor.
Hydro electric power plant
This document summarizes different types of hydroelectric power plants and turbines. It describes impulse and reaction turbines, including Pelton, Francis, and Kaplan turbines. It provides diagrams of hydroelectric and pump storage plants. Key concepts covered include gross and net heads, discharge, water power, brake power, efficiency, and speed. Fundamental equations for hydroelectric systems are given. Common terms are defined. Sample problems demonstrate calculations for hydroelectric plant design and performance analysis.
Unit2 fluid static
The document discusses fluid pressure and its relationship to depth. It introduces Pascal's law and how it applies to hydraulic systems. Specifically:
1) Pressure increases with depth in fluids due to the weight of the fluid above pushing down. Pascal's law states that pressure increases are equal throughout a confined fluid.
2) Hydraulic systems use this principle to multiply forces. A small force applied to a piston with a small surface area can create a much larger force when transmitted through fluid to a piston with a larger surface area.
3) An example is given of a hydraulic car lift, where 1 kg applied to a small piston creates enough pressure to lift 10 kg with a larger piston, multiplying the applied
Continuity Equation
1. The document discusses the continuity equation, which states that the flow rate of an incompressible fluid is constant at any point in a fluid system with no accumulation.
2. The formula for continuity equation is given as: ρ1A1v1 = ρ2A2v2, where ρ is density, A is cross-sectional area, and v is velocity.
3. Examples of applications include calculating water velocity changes in pipes or rivers of varying diameters, and a sample problem is worked out calculating velocities at different pipe positions.
Fluid Mechanics Chapter 5. Dimensional Analysis and Similitude
Introduction, Dimensional homogeneity, Buckingham pi theorem, Non dimensionalization of basic equations, Similitude, Significance of non-dimensional numbers in fluid flows
Specific volume of steam
This document discusses key concepts related to the specific volume and internal energy of steam. It defines specific volume as the volume occupied by 1 kg of a substance. It then defines specific volumes for saturated water, dry saturated steam, wet steam, and superheated steam. The specific volume of steam increases with temperature. It also discusses how to calculate the internal energy of dry steam, wet steam, and superheated steam using enthalpy, pressure, and specific volume. Finally, it defines internal latent heat as the difference between enthalpy of evaporation and work of evaporation.
Fluid Mechanics Chapter 7. Compressible flow
Introduction, Speed of sound, Steady flow, Flow with area change- Nozzles and Diffusers, Normal shock wave, Duct flow with friction
Thermo problem set no. 1
This document contains 20 multiple choice problems related to mechanical engineering. The problems cover topics such as fluid mechanics, thermodynamics, heat transfer, and other mechanical engineering principles. They involve calculations related to things like tank volumes, pressure differences, flow rates, heat transfer between substances, and more. The questions provide relevant equations, known values, and ask the reader to determine unknown values or temperatures based on the given information.
Unit7
The document discusses the application of the steady flow energy equation to various flow processes including turbines, nozzles, throttles, and pumps. It explains that for turbines, the steady flow energy equation relates the enthalpy drop of the fluid to the work produced. For nozzles, the equation shows the relationship between the enthalpy drop and the kinetic energy increase of the fluid. For throttles, the equation indicates that the enthalpy remains constant. And for pumps, the equation relates the enthalpy rise to the work input into the system. Examples are provided to demonstrate how to use the steady flow energy equation to analyze different flow processes.
Fluid Mechanics - Fluid Dynamics
Topics:
1. Introduction to Fluid Dynamics
2. Surface and Body Forces
3. Equations of Motion
- Reynold’s Equation
- Navier-Stokes Equation
- Euler’s Equation
- Bernoulli’s Equation
- Bernoulli’s Equation for Real Fluid
4. Applications of Bernoulli’s Equation
5. The Momentum Equation
6. Application of Momentum Equations
- Force exerted by flowing fluid on pipe bend
- Force exerted by the nozzle on the water
7. Measurement of Flow Rate
a). Venturimeter
b). Orifice Meter
c). Pitot Tube
8. Measurement of Flow Rate in Open Channels
a) Notches
b) Weirs
Fluid Mechanics Chapter 2. Fluid Statics
Introduction, Pressure specifications, Hydrostatic pressure distributions, Manometer, Hydrostatic Forces on plane surfaces, Hydrostatic forces on curved surfaces, Buoyancy and Stability, Pressure variation with rigid body motion
Fluid discharge
1) The document discusses fluid flow through orifices and mouthpieces. It describes the theory of small orifices discharging fluid using Bernoulli's equation and defines relevant terms like coefficient of velocity and coefficient of discharge.
2) Torricelli's theorem states the velocity of a discharging jet is proportional to the square root of the head producing flow. The theoretical discharge can be calculated using the orifice area and velocity.
3) Examples are provided to demonstrate calculating coefficients of velocity, discharge, and contraction for given orifice dimensions and fluid flow values.
MICROSCOPIC & MACROSCOPIC POINT OF VIEW , THERMODYNAMIC SYSTEM & CONTROL VO...
Thermodynamics is science of energy transfer and its effects on properties.
Main aim is to convert disorganized form of energy into organized form of energy in an efficient manner. Based on the macroscopic approach which does not require knowledge of behavior of individual particles and is called classical thermodynamics.
compressor notes.pdf
The document summarizes key concepts about reciprocating air compressors:
1) It describes the basic components and working of a single-stage, double-acting reciprocating air compressor using a labeled diagram. The compressor consists of a piston that reciprocates in a cylinder driven by a crankshaft, with inlet and outlet valves.
2) It explains the ideal thermodynamic cycle on p-V and T-S diagrams, involving constant-pressure intake, adiabatic compression, and constant-pressure discharge processes.
3) It defines mechanical efficiency and indicated power for reciprocating compressors, and describes calculations for work of compression and various efficiencies like isothermal efficiency.
PROCESS GAS COMPRESSOR AND PT OVERHAULING
Overhauling of a machine is defined as a process of general maintenance performed on a machine or other industrial equipment. The goal of overhauling is to keep the system in serviceable condition. Regular checks can prevent all kinds of critical damage.
Overhauling is the effective maintenance program should be such that the basic objective is achieved with minimum possible expenditure. The availability of turbine, and mainly the operating reliability, depends on the satisfactory operation of its control, protection of ancillary equipment such as pumps etc. The study deals with the tests and maintenance necessary to ensure good operating reliability for the turbine. The Turbine Overhauling work is generally done during a planned shutdown. An overhauling is a detailed inspection and overhaul of the entire gas turbine set including the turbine casing, rotor, seals, and bearings; the generator; and auxiliaries such as the gear, couplings, lubrication system, and controls.
AFD - Incompressible Flow - Introduction
This document provides an overview of an online course on applied fluid mechanics for incompressible flow. The course is divided into two parts, with part 1 focusing on incompressible flow (constant density fluids) and part 2 on compressible flow (variable density fluids). Part 1 covers topics like the mechanic energy equation, piping systems, pumps, flow measurement devices, and their applications to problems involving incompressible fluids. The course content is presented through online modules containing theory, examples, practice problems and quizzes. The goal is to teach students and engineers how to apply fluid mechanics concepts to real-world engineering problems involving the movement and processing of incompressible liquids and gases.
Flow In Pipes
This document discusses laminar and turbulent flow in pipes. It defines the critical Reynolds number that distinguishes between the two flow regimes. For non-circular pipes, it introduces the hydraulic diameter to characterize the pipe geometry. The document then covers topics such as the developing flow region, fully developed flow profiles and pressure drop, the friction factor, minor losses, pipe networks, and pump selection.
Venturimeter : Working,Construction,Applications ,Numerical
Here are the steps to solve this problem:
1. Given:
Inlet diameter (d1) = 200 mm = 0.2 m
Throat diameter (d2) = 100 mm = 0.1 m
Specific gravity of oil (Sf) = 0.9
2. Calculate the areas:
Inlet area (A1) = πr12 = π(0.1)2 = 0.0314 m2
Throat area (A2) = πr22 = π(0.05)2 = 0.00785 m2
3. Use the venturimeter discharge equation:
Q = Cd * A1*
TURBINE PERFORMANCE CURVES
This presentation deals with CONSTANT HEAD,CONSTANT SPEED,CONSTANT EFFICIENCY & CAVITATION in hydraulic turbines
Hydraulic Turbines
1. The document discusses various topics related to hydraulic turbines including their classification, selection, design principles of Pelton, Francis and Kaplan turbines, draft tubes, surge tanks, governing, unit quantities, characteristic curves, similitude analysis and cavitation.
2. Hydraulic turbines are classified based on the type of energy at the inlet, direction of flow through the runner, head at the inlet, and specific speed. Pelton wheels are impulse turbines suitable for high heads while Francis and Kaplan turbines are reaction turbines for lower heads.
3. The design of each turbine type involves guidelines related to jet ratio, speed ratio, velocities, discharge, power and efficiency calculations. Characteristic curves show the performance of a
Fluid mechanics question bank
Muhammed Fuad Rashid
Petroleum Engineering Department at Koya University
Fluid Mechanics Question bank by Dr. Jafar Dalo
2020
220228718-Engineering-Thermodynamics-Tutorial.pdf
This document contains tutorial sheets on thermodynamic properties, energy transfer, and properties of common substances from the Department of Mechanical Engineering at the Institute of Engineering Pulchowk Campus. The tutorials include examples calculating thermodynamic properties like pressure, volume, temperature and phase changes for systems undergoing various processes. They provide the fundamental concepts and equations needed to understand thermodynamics and heat transfer.
MET212-Assignment 2
This document provides instructions for Assignment 2 in a fluid mechanics and machines course. It includes 4 problems to solve: 1) calculating the maximum water depth and moment on a rectangular gate, 2) calculating the absolute pressure at a point in a pipe using a double U-tube manometer, 3) determining the value of h1 using a manometer to measure tank pressure, and 4) calculating the pressure difference between two pipes connected by an inverted U-tube manometer. Students are to submit their individual work on the problems by the specified due dates.
More Related Content
What's hot
Hydro electric power plant
This document summarizes different types of hydroelectric power plants and turbines. It describes impulse and reaction turbines, including Pelton, Francis, and Kaplan turbines. It provides diagrams of hydroelectric and pump storage plants. Key concepts covered include gross and net heads, discharge, water power, brake power, efficiency, and speed. Fundamental equations for hydroelectric systems are given. Common terms are defined. Sample problems demonstrate calculations for hydroelectric plant design and performance analysis.
Unit2 fluid static
The document discusses fluid pressure and its relationship to depth. It introduces Pascal's law and how it applies to hydraulic systems. Specifically:
1) Pressure increases with depth in fluids due to the weight of the fluid above pushing down. Pascal's law states that pressure increases are equal throughout a confined fluid.
2) Hydraulic systems use this principle to multiply forces. A small force applied to a piston with a small surface area can create a much larger force when transmitted through fluid to a piston with a larger surface area.
3) An example is given of a hydraulic car lift, where 1 kg applied to a small piston creates enough pressure to lift 10 kg with a larger piston, multiplying the applied
Continuity Equation
1. The document discusses the continuity equation, which states that the flow rate of an incompressible fluid is constant at any point in a fluid system with no accumulation.
2. The formula for continuity equation is given as: ρ1A1v1 = ρ2A2v2, where ρ is density, A is cross-sectional area, and v is velocity.
3. Examples of applications include calculating water velocity changes in pipes or rivers of varying diameters, and a sample problem is worked out calculating velocities at different pipe positions.
Fluid Mechanics Chapter 5. Dimensional Analysis and Similitude
Introduction, Dimensional homogeneity, Buckingham pi theorem, Non dimensionalization of basic equations, Similitude, Significance of non-dimensional numbers in fluid flows
Specific volume of steam
This document discusses key concepts related to the specific volume and internal energy of steam. It defines specific volume as the volume occupied by 1 kg of a substance. It then defines specific volumes for saturated water, dry saturated steam, wet steam, and superheated steam. The specific volume of steam increases with temperature. It also discusses how to calculate the internal energy of dry steam, wet steam, and superheated steam using enthalpy, pressure, and specific volume. Finally, it defines internal latent heat as the difference between enthalpy of evaporation and work of evaporation.
Fluid Mechanics Chapter 7. Compressible flow
Introduction, Speed of sound, Steady flow, Flow with area change- Nozzles and Diffusers, Normal shock wave, Duct flow with friction
Thermo problem set no. 1
This document contains 20 multiple choice problems related to mechanical engineering. The problems cover topics such as fluid mechanics, thermodynamics, heat transfer, and other mechanical engineering principles. They involve calculations related to things like tank volumes, pressure differences, flow rates, heat transfer between substances, and more. The questions provide relevant equations, known values, and ask the reader to determine unknown values or temperatures based on the given information.
Unit7
The document discusses the application of the steady flow energy equation to various flow processes including turbines, nozzles, throttles, and pumps. It explains that for turbines, the steady flow energy equation relates the enthalpy drop of the fluid to the work produced. For nozzles, the equation shows the relationship between the enthalpy drop and the kinetic energy increase of the fluid. For throttles, the equation indicates that the enthalpy remains constant. And for pumps, the equation relates the enthalpy rise to the work input into the system. Examples are provided to demonstrate how to use the steady flow energy equation to analyze different flow processes.
Fluid Mechanics - Fluid Dynamics
Topics:
1. Introduction to Fluid Dynamics
2. Surface and Body Forces
3. Equations of Motion
- Reynold’s Equation
- Navier-Stokes Equation
- Euler’s Equation
- Bernoulli’s Equation
- Bernoulli’s Equation for Real Fluid
4. Applications of Bernoulli’s Equation
5. The Momentum Equation
6. Application of Momentum Equations
- Force exerted by flowing fluid on pipe bend
- Force exerted by the nozzle on the water
7. Measurement of Flow Rate
a). Venturimeter
b). Orifice Meter
c). Pitot Tube
8. Measurement of Flow Rate in Open Channels
a) Notches
b) Weirs
Fluid Mechanics Chapter 2. Fluid Statics
Introduction, Pressure specifications, Hydrostatic pressure distributions, Manometer, Hydrostatic Forces on plane surfaces, Hydrostatic forces on curved surfaces, Buoyancy and Stability, Pressure variation with rigid body motion
Fluid discharge
1) The document discusses fluid flow through orifices and mouthpieces. It describes the theory of small orifices discharging fluid using Bernoulli's equation and defines relevant terms like coefficient of velocity and coefficient of discharge.
2) Torricelli's theorem states the velocity of a discharging jet is proportional to the square root of the head producing flow. The theoretical discharge can be calculated using the orifice area and velocity.
3) Examples are provided to demonstrate calculating coefficients of velocity, discharge, and contraction for given orifice dimensions and fluid flow values.
MICROSCOPIC & MACROSCOPIC POINT OF VIEW , THERMODYNAMIC SYSTEM & CONTROL VO...
Thermodynamics is science of energy transfer and its effects on properties.
Main aim is to convert disorganized form of energy into organized form of energy in an efficient manner. Based on the macroscopic approach which does not require knowledge of behavior of individual particles and is called classical thermodynamics.
compressor notes.pdf
The document summarizes key concepts about reciprocating air compressors:
1) It describes the basic components and working of a single-stage, double-acting reciprocating air compressor using a labeled diagram. The compressor consists of a piston that reciprocates in a cylinder driven by a crankshaft, with inlet and outlet valves.
2) It explains the ideal thermodynamic cycle on p-V and T-S diagrams, involving constant-pressure intake, adiabatic compression, and constant-pressure discharge processes.
3) It defines mechanical efficiency and indicated power for reciprocating compressors, and describes calculations for work of compression and various efficiencies like isothermal efficiency.
PROCESS GAS COMPRESSOR AND PT OVERHAULING
Overhauling of a machine is defined as a process of general maintenance performed on a machine or other industrial equipment. The goal of overhauling is to keep the system in serviceable condition. Regular checks can prevent all kinds of critical damage.
Overhauling is the effective maintenance program should be such that the basic objective is achieved with minimum possible expenditure. The availability of turbine, and mainly the operating reliability, depends on the satisfactory operation of its control, protection of ancillary equipment such as pumps etc. The study deals with the tests and maintenance necessary to ensure good operating reliability for the turbine. The Turbine Overhauling work is generally done during a planned shutdown. An overhauling is a detailed inspection and overhaul of the entire gas turbine set including the turbine casing, rotor, seals, and bearings; the generator; and auxiliaries such as the gear, couplings, lubrication system, and controls.
AFD - Incompressible Flow - Introduction
This document provides an overview of an online course on applied fluid mechanics for incompressible flow. The course is divided into two parts, with part 1 focusing on incompressible flow (constant density fluids) and part 2 on compressible flow (variable density fluids). Part 1 covers topics like the mechanic energy equation, piping systems, pumps, flow measurement devices, and their applications to problems involving incompressible fluids. The course content is presented through online modules containing theory, examples, practice problems and quizzes. The goal is to teach students and engineers how to apply fluid mechanics concepts to real-world engineering problems involving the movement and processing of incompressible liquids and gases.
Flow In Pipes
This document discusses laminar and turbulent flow in pipes. It defines the critical Reynolds number that distinguishes between the two flow regimes. For non-circular pipes, it introduces the hydraulic diameter to characterize the pipe geometry. The document then covers topics such as the developing flow region, fully developed flow profiles and pressure drop, the friction factor, minor losses, pipe networks, and pump selection.
Venturimeter : Working,Construction,Applications ,Numerical
Here are the steps to solve this problem:
1. Given:
Inlet diameter (d1) = 200 mm = 0.2 m
Throat diameter (d2) = 100 mm = 0.1 m
Specific gravity of oil (Sf) = 0.9
2. Calculate the areas:
Inlet area (A1) = πr12 = π(0.1)2 = 0.0314 m2
Throat area (A2) = πr22 = π(0.05)2 = 0.00785 m2
3. Use the venturimeter discharge equation:
Q = Cd * A1*
TURBINE PERFORMANCE CURVES
This presentation deals with CONSTANT HEAD,CONSTANT SPEED,CONSTANT EFFICIENCY & CAVITATION in hydraulic turbines
Hydraulic Turbines
1. The document discusses various topics related to hydraulic turbines including their classification, selection, design principles of Pelton, Francis and Kaplan turbines, draft tubes, surge tanks, governing, unit quantities, characteristic curves, similitude analysis and cavitation.
2. Hydraulic turbines are classified based on the type of energy at the inlet, direction of flow through the runner, head at the inlet, and specific speed. Pelton wheels are impulse turbines suitable for high heads while Francis and Kaplan turbines are reaction turbines for lower heads.
3. The design of each turbine type involves guidelines related to jet ratio, speed ratio, velocities, discharge, power and efficiency calculations. Characteristic curves show the performance of a
Fluid mechanics question bank
Muhammed Fuad Rashid
Petroleum Engineering Department at Koya University
Fluid Mechanics Question bank by Dr. Jafar Dalo
2020
What's hot (20)
Fluid Mechanics Chapter 5. Dimensional Analysis and Similitude
Fluid Mechanics Chapter 5. Dimensional Analysis and Similitude
MICROSCOPIC & MACROSCOPIC POINT OF VIEW , THERMODYNAMIC SYSTEM & CONTROL VO...
MICROSCOPIC & MACROSCOPIC POINT OF VIEW , THERMODYNAMIC SYSTEM & CONTROL VO...
Venturimeter : Working,Construction,Applications ,Numerical
Venturimeter : Working,Construction,Applications ,Numerical
Similar to 2 tutor pressure 1
220228718-Engineering-Thermodynamics-Tutorial.pdf
This document contains tutorial sheets on thermodynamic properties, energy transfer, and properties of common substances from the Department of Mechanical Engineering at the Institute of Engineering Pulchowk Campus. The tutorials include examples calculating thermodynamic properties like pressure, volume, temperature and phase changes for systems undergoing various processes. They provide the fundamental concepts and equations needed to understand thermodynamics and heat transfer.
MET212-Assignment 2
This document provides instructions for Assignment 2 in a fluid mechanics and machines course. It includes 4 problems to solve: 1) calculating the maximum water depth and moment on a rectangular gate, 2) calculating the absolute pressure at a point in a pipe using a double U-tube manometer, 3) determining the value of h1 using a manometer to measure tank pressure, and 4) calculating the pressure difference between two pipes connected by an inverted U-tube manometer. Students are to submit their individual work on the problems by the specified due dates.
Me 12 quiz no. 3
1. The document contains 4 problems involving compressed gases and thermodynamic processes. Problem 1 involves determining the pressure reading of a manometer connected to a tank containing compressed air and oil. Problem 2 involves determining the air pressure in a storage tank using the pressure reading in a pipe containing a different fluid. Problem 3 involves calculating the work done and heat transferred during an isothermal expansion process of air in a piston cylinder device. Problem 4 involves sketching and analyzing an isothermal compression followed by a constant pressure compression process of air on PV and TS diagrams.
MET212-Assinment 2
This document contains 7 questions related to fluid mechanics and machines. Question 1 asks to determine the heights of water and oil in the arms of a U-tube manometer. Question 2 asks to calculate the load that can be lifted by a hydraulic jack with given piston areas and an applied force. Question 3 asks to calculate pressure heads of different liquids corresponding to a given pressure. Question 4 asks to calculate the pressure at the bottom of a tank partially filled with glycerin. Questions 5-7 ask calculation questions related to pressure differences and forces in fluid systems.
Manometers.pptx
Here are the solutions to the assignment problems:
1. Given: Pressure = 40 m of oil of specific gravity 0.6
Density of oil (ρo) = 0.6 x 1000 = 600 kg/m3
Density of mercury (ρm) = 13,600 kg/m3
Using the formula: ρ1h1 = ρ2h2
ρoh = ρmh
600 x 40 = 13,600 h
h = 40 x 13,600/600 = 68 m of mercury
2. Given pressures:
(a) 150 kPa
(b) 1800 millibars
(c) 20 m of water
(d) 1240 mm
Flow around a bent duct theory
The document summarizes an experiment investigating flow around a 90-degree bend in a rectangular duct. Pressure measurements were taken along the inner and outer curved walls and across a radial section of the bend. The measurements showed that pressure decreases around the inner wall and increases around the outer wall, as predicted by assuming a free vortex velocity distribution in the bend. The pressure distribution across the radial section also closely matched the calculated values. The loss coefficient for pressure loss around the bend was determined to be 0.15 based on the change in pressure coefficient from the inlet to outlet sections.
Unit7 nozzles
This document discusses nozzles and provides objectives and information about different types of nozzles. It defines nozzles and diffusers, describes convergent and convergent-divergent nozzle shapes. It also defines critical pressure ratio and maximum mass flow, and provides equations to calculate properties like area, temperature, and velocity at different points in a nozzle. An example calculation is provided to demonstrate determining the throat and exit areas of a convergent-divergent nozzle.
Buku bab 2
This document provides information about fluid mechanics concepts including fluid statics, pressure measurement, buoyancy, and examples. It begins with definitions of key terms like pressure, density, and height in fluid statics. It then gives examples of calculating pressure at various depths. Next, it discusses pressure measurement tools like manometers and bourdon gauges. It defines buoyancy force and provides an example calculation. Finally, it gives several example problems calculating quantities like buoyant force, draught, and liquid levels based on densities, dimensions, and weights.
Unit 3 Fluid Static
This document provides objectives and information about pressure measurement techniques. It discusses piezometers, barometers, bourdon gauges, and several types of manometers. The key points are:
- Piezometers, barometers, bourdon gauges, and manometers can be used to measure pressure.
- Piezometers use the height of liquid in a tube to determine pressure. Barometers measure atmospheric pressure using the height of a mercury column.
- Bourdon gauges use the deflection of a curved tube to indicate pressure differences over 1 bar.
- Manometers like the simple and differential types utilize the relationship between pressure and liquid height to measure pressures.
MET 212 Assignment-2
This document contains an assignment for a fluid mechanics and machines course. It includes 7 questions related to fluid properties, hydraulic jacks, pressure differences, and forces on submerged structures. The questions are presented along with the assignment instructions, which specify the student name, ID number, section, and date. Diagrams are included to illustrate some of the systems described in the questions.
MET 212 Cw 2
This document contains 5 fluid mechanics questions and diagrams related to determining pressures using manometers, fluid columns, and specific gravities. Question 1 asks to determine the gauge pressure for a multi-fluid open container connected to a U-tube given specific gravities and fluid column heights. Question 2 asks to determine the differential height of a mercury column for a given air pressure in a tank. Question 3 asks to find the gauge pressure reading for a mercury manometer connected to a closed tank containing mercury. Question 4 asks to determine the gauge pressure for a tank containing compressed air and oil connected to a mercury U-tube manometer given various fluid column heights. Question 5 asks to determine the heights of oil and water in the right arm of
Minor losses valve
Muhammed Fuad Rashid
Petroleum Engineering Department at Koya Universiy
Fluid Mechanics Laboratory
2020
Tutorial # 3 +solution
This document contains 6 practice problems related to fluid mechanics:
1) Calculating the specific gravity of a fluid given tank pressures
2) Finding the angle of tilt of a tube open to the atmosphere
3) Calculating pressures at different points in a system of connected containers and cavities
4) Determining the differential height of a mercury column given an air pressure
5) Finding air pressure and equilibrium mercury levels in a tank with multiple fluids
6) Calculating the amplification factor of a manometer setup using oil instead of water.
Flow measurement basics
This document describes different flow measurement devices including the venturi meter, orifice plate, and rotameter. It provides details on how each device works based on pressure differences caused by a flow restriction. The objectives are to study and compare the characteristics of venturi meters and orifice plates, calculate flow rates using measured pressure drops, and understand how rotameters operate based on the position of a float. An apparatus is described that can be used to collect pressure and flow rate data from each device to analyze flow measurement principles.
Pressure Calibrations and Standard
No definition of pressure is really useful to the engineer until it is translated into measurable characteristics.
Pressure standards are the basis of all pressure measurements.
Pneumatic c5
A basic hydraulic circuit consists of a power supply, pump, reservoir, relief valve and control valve. Common control valves include mechanically or solenoid operated valves, open or closed center valves. Common pumps include gear, piston, vane, and tandem pumps. Additional components are flow control valves, selector valves, flow dividers, check valves, and relief valves. Proper interaction of these components allows for control of hydraulic cylinders, motors, and remote fluid distribution.
Laboratorio final artículo
1. A homemade manometer was constructed to measure the pressure of air stored in a balloon and calculate the density of oil using pressure ratios.
2. Air pressure and volume measurements from the balloon were taken at different volumes and followed the ideal gas law relationship.
3. Oil density calculations from manometer height differences matched literature values for olive oil density, though some error was present from measurement imprecision.
03 1 bsb 228 pressure and pressure measurement
03 1 bsb 228 pressure and pressure measurementBotswana University of Agriculture and Natural Resources
The document provides information about pressure measurement devices. It discusses the barometer and how it is used to measure atmospheric pressure by measuring the height of a mercury column. It also discusses manometers, which are commonly used to measure small and moderate pressure differences by using different fluids in a U-tube configuration. Differential manometers can be used to measure pressure drops across sections in a flow system by connecting the legs of the manometer to the two points of interest.Engineering Fluid Mechanics 11th Edition Elger Solutions Manual
Full download : https://alibabadownload.com/product/engineering-fluid-mechanics-11th-edition-elger-solutions-manual/ Engineering Fluid Mechanics 11th Edition Elger Solutions Manual
Minor losses elbow
1. The document describes an experiment to calculate the loss coefficient (K) for different pipe components, including pipe bends, branches, and changes in cross-section.
2. Tests were conducted to measure the minor losses through pipe elbows at various angles, double elbows, and a single elbow.
3. The loss coefficients were calculated based on measurements of pressure difference, flow velocity, and component geometry. Loss coefficients ranged from 0.548 to 2.345 depending on the pipe component.
Similar to 2 tutor pressure 1 (20)
Engineering Fluid Mechanics 11th Edition Elger Solutions Manual
Engineering Fluid Mechanics 11th Edition Elger Solutions Manual
Recently uploaded
What do the symbols on vehicle dashboard mean?
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Catalytic Converter theft prevention - NYC.pptx
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
快速办理(napier毕业证书)英国龙比亚大学毕业证在读证明一模一样
学校原件一模一样【微信：741003700 】《(napier毕业证书)英国龙比亚大学毕业证》【微信：741003700 】学位证，留信认证（真实可查，永久存档）原件一模一样纸张工艺/offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原。
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
【主营项目】
一.毕业证【q微741003700】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【q/微741003700】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
EV Charging at Multifamily Properties by Kevin Donnelly
Kevin Donnelly gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill Roads
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Here's Why Every Semi-Truck Should Have ELDs
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
一比一原版(WashU文凭证书)圣路易斯华盛顿大学毕业证如何办理
一模一样【微信：176555708】【(WashU文凭证书)圣路易斯华盛顿大学毕业证成绩单Offer】【微信：176555708】（留信学历认证永久存档查询）采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
【业务选择办理准则】
一、工作未确定，回国需先给父母、亲戚朋友看下文凭的情况，办理一份就读学校的毕业证【微信：176555708】文凭即可
二、回国进私企、外企、自己做生意的情况，这些单位是不查询毕业证真伪的，而且国内没有渠道去查询国外文凭的真假，也不需要提供真实教育部认证。鉴于此，办理一份毕业证【微信：176555708】即可
三、进国企，银行，事业单位，考公务员等等，这些单位是必需要提供真实教育部认证的，办理教育部认证所需资料众多且烦琐，所有材料您都必须提供原件，我们凭借丰富的经验，快捷的绿色通道帮您快速整合材料，让您少走弯路。
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
→ 【关于价格问题（保证一手价格）
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
选择实体注册公司办理，更放心，更安全！我们的承诺：可来公司面谈，可签订合同，会陪同客户一起到教育部认证窗口递交认证材料，客户在教育部官方认证查询网站查询到认证通过结果后付款，不成功不收费！
EV Charging at MFH Properties by Whitaker Jamieson
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa Warheit
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
原版制作(Exeter毕业证书)埃克塞特大学毕业证完成信一模一样
学校原件一模一样【微信：741003700 】《(Exeter毕业证书)埃克塞特大学毕业证》【微信：741003700 】学位证，留信认证（真实可查，永久存档）原件一模一样纸张工艺/offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原。
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
【主营项目】
一.毕业证【q微741003700】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【q/微741003700】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
一比一原版(Columbia文凭证书)哥伦比亚大学毕业证如何办理
一模一样【微信：176555708】【(Columbia文凭证书)哥伦比亚大学毕业证成绩单Offer】【微信：176555708】（留信学历认证永久存档查询）采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
【业务选择办理准则】
一、工作未确定，回国需先给父母、亲戚朋友看下文凭的情况，办理一份就读学校的毕业证【微信：176555708】文凭即可
二、回国进私企、外企、自己做生意的情况，这些单位是不查询毕业证真伪的，而且国内没有渠道去查询国外文凭的真假，也不需要提供真实教育部认证。鉴于此，办理一份毕业证【微信：176555708】即可
三、进国企，银行，事业单位，考公务员等等，这些单位是必需要提供真实教育部认证的，办理教育部认证所需资料众多且烦琐，所有材料您都必须提供原件，我们凭借丰富的经验，快捷的绿色通道帮您快速整合材料，让您少走弯路。
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
→ 【关于价格问题（保证一手价格）
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
选择实体注册公司办理，更放心，更安全！我们的承诺：可来公司面谈，可签订合同，会陪同客户一起到教育部认证窗口递交认证材料，客户在教育部官方认证查询网站查询到认证通过结果后付款，不成功不收费！
Hand Gesture Control Robotic Arm using image processing.pptx
Hand Gesture Control Robotic Arm using image processing
AadiShakti Projects ( Asp Cranes ) Raipur
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Recently uploaded (17)
EV Charging at Multifamily Properties by Kevin Donnelly
EV Charging at Multifamily Properties by Kevin Donnelly
Globalfleet - global fleet survey 2021 full results
Globalfleet - global fleet survey 2021 full results
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill Roads
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill Roads
53286592-Global-Entrepreneurship-and-the-Successful-Growth-Strategies-of-Earl...
53286592-Global-Entrepreneurship-and-the-Successful-Growth-Strategies-of-Earl...
EV Charging at MFH Properties by Whitaker Jamieson
EV Charging at MFH Properties by Whitaker Jamieson
Expanding Access to Affordable At-Home EV Charging by Vanessa Warheit
Expanding Access to Affordable At-Home EV Charging by Vanessa Warheit
Hand Gesture Control Robotic Arm using image processing.pptx
Hand Gesture Control Robotic Arm using image processing.pptx
2 tutor pressure 1
- 1. PROBLEMS FOR CHAPTER 2 - PRESSURE Question 1 The basic elements of a hydraulic press are shown in Figure 1. The plunger has an area of 3-cm2 , and a force, F1, can be applied to the plunger through a lever mechanism having a mechanical advantage of 8 to 1. If the large piston has an area of 150 cm2 , what load, F2, can be raised by a force of 30 N applied to the lever? Neglect the hydrostatic pressure variation. Figure 1 Question 2 A U-tube manometer is connected to a closed tank containing air and water as shown in Figure 2. At the closed end of the manometer the absolute air pressure is 140kPa. Determine the reading on the pressure gage for a differential reading of 1.5-m on the manometer. Express your answer in gage pressure value. Assume standard atmospheric pressure and neglect the weight of the air columns in the manometer. Figure 2 1
- 2. Question 3 A closed cylindrical tank filled with water has a hemispherical dome and is connected to an inverted piping system as shown in Figure 3. The liquid in the top part of the piping system has a specific gravity of 0.8, and the remaining parts of the system are filled with water. If the pressure gage reading at A is 60 kPa, determine: (a) the pressure in pipe B, and (b) the pressure head, in millimeters of mercury, at the top of the dome (point C). Figure 3 Question 4 A U-tube manometer contains oil, mercury, and water as shown in Figure 4. For the column heights indicated what is the pressure differential between pipes A and B? Figure 4 2
- 3. Question 5 A U-tube manometer is connected to a closed tank as shown in Figure 5. The air pressure in the tank is 120 Pa and the liquid in the tank is oil (γ = 12000 N/m3 ). The pressure at point A is 20 kPa. Determine: (a) the depth of oil, z, and (b) the differential reading, h, on the manometer. Figure 5 Question 6 The inverted U-tube manometer of Figure 6 contains oil (SG = 0.9) and water as shown. The pressure differential between pipes A and B, pA − pB, is −5 kPa. Determine the differential reading, h. Figure 6 3
- 4. Question 7 A piston having a cross-sectional area of 0.07 m2 is located in a cylinder containing water as shown in Figure 7. An open U-tube manometer is connected to the cylinder as shown. For h1 = 60 mm and h = 100 mm, what is the value of the applied force, P, acting on the piston? The weight of the piston is negligible. Figure 7 Question 8 For the inclined-tube manometer of Figure 8, the pressure in pipe A is 8 kPa. The fluid in both pipes A and B is water, and the gage fluid in the manometer has a specific gravity of 2.6. What is the pressure in pipe B corresponding to the differential reading shown? Figure 8 4
- 5. Answer : 1. 12 kN 2. 66.8 kPa 3. (a) 103.2 kPa (b) 229 mm 4. -20.7 kPa 5. z = 1.66 m h = 1.37 m 6. 0.46 mm 7. 892.7 N 8. 5508.3 Pa 5