This thesis summarizes an optimization study performed on a connecting rod for an internal combustion engine. Finite element analysis was used to analyze stress from tensile and compressive forces. The highest stress occurred at the top of the shank fillet. Various fillet sizes and materials were analyzed, with a 10mm fillet and low alloy steel reducing stress the most. Manufacturing methods like forging and powder metallurgy were considered for cost effectiveness, with powder metallurgy chosen. The optimization reduced weight by 9.38% while increasing the safety factor over 50%.
In our country we are facing tremendous problems because of electricity shortage and the J&K state is on top. We are considered rich in production of electricity but the truth is we are not getting the desired. The solution is implementation of latest and emerging technologies like IOT and Microcontrollers in electrical domain. The paper describes the need of technology for load shedding process. Itika Sharma | Shavet Sharma"Load Shedding Management" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-2 | Issue-5 , August 2018, URL: http://www.ijtsrd.com/papers/ijtsrd18364.pdf http://www.ijtsrd.com/engineering/electrical-engineering/18364/load-shedding-management/itika-sharma
Shape memory alloys are metal alloys that can be deformed at one temperature but return to their original shape when heated or cooled. The most common alloys are nickel-titanium (Nitinol), copper-zinc-aluminum, and copper-aluminum-nickel. Nitinol was discovered in the 1960s and is now used widely in applications such as medical devices, aircraft, and household appliances. Shape memory alloys work through a solid state phase change between martensite and austenite phases - deforming occurs in the martensite phase while heating triggers shape recovery in the austenite phase. They provide advantages like biocompatibility and diverse applications but also
This study encapsulated equine endothelial progenitor cells and mesenchymal stem cells alone and in co-culture within a PEG-fibrinogen hydrogel scaffold to assess neovascularization. Equine EPCs formed tubules within 1 day when encapsulated alone or with MSCs, and vascularization increased over 4 days. Tubules did not form with MSCs alone. The hydrogel scaffold supported long-term cell viability and vascular structure formation, demonstrating its potential for tissue engineering and wound healing applications in horses. Future work will quantify vessel formation to determine scaffold thickness and MSC effects.
This document discusses corrosion resistant materials for extreme environments. It begins with an introduction that defines corrosion and extreme environments. It then reviews literature on the corrosion properties of various nickel alloys, high entropy alloys, and MCrAlY coatings. Next, it describes various corrosion resistant metals like stainless steels, nickel and aluminum alloys. It discusses recent developments in high entropy alloys and metal coatings. Finally, it provides two case studies on corrosion issues in nuclear power plants and gas turbine blades.
The Assembly Line and Mass Production Presentationerinlord
The assembly line and mass production transformed industry in the United States through increased efficiency, lower production costs, and higher profits. An assembly line divides the production process into sequential steps with different workers performing specialized tasks, allowing products like Ford's Model T to be mass produced. This innovation utilized unskilled labor, interchangeable parts, and mechanization to build custom products on a large scale, driving down costs and prices while increasing availability to consumers.
This document presents a rolling mechanism based piezoelectric vibration energy harvester. It begins with an introduction to energy harvesting, describing it as gathering energy from ambient sources like motion and converting it into electricity. It then discusses piezoelectric energy harvesting techniques and describes the basic structure of the rolling mechanism harvester. The harvester is designed to convert oscillating vibrations into rolling motion in order to amplify force and increase harvested energy output. Experimental results show the harvester is able to generate a stable DC voltage regardless of vibration frequency or amplitude.
Magnetorheological fluids are liquids that can change from liquid to solid when exposed to a magnetic field. They consist of magnetizable particles suspended in a carrier fluid like oil or water. As a magnetic field is applied, the particles form chains and structures that increase the fluid's viscosity and yield stress. MR fluids have applications in vehicle suspension dampers and transmissions where they allow precise control and fast response times to dampen vibrations or control torque transmission. Their properties can be controlled electronically and they require low power levels compared to similar smart fluids.
This document provides examples and uses of smart materials. It begins by defining smart materials as materials that react quickly to a stimulus in a specific manner. Examples given include materials that change color or shape in response to temperature, contact with water, electrical current, or light. Common uses of smart materials are in sensors, transducers, printers, and medical applications. Shape memory alloys, magnetorheological fluids, and thermochromic materials are also discussed along with various applications. The document concludes by mentioning some modern smart materials like thermochromic sheets, polymorphs, and quantum tunneling composites.
In our country we are facing tremendous problems because of electricity shortage and the J&K state is on top. We are considered rich in production of electricity but the truth is we are not getting the desired. The solution is implementation of latest and emerging technologies like IOT and Microcontrollers in electrical domain. The paper describes the need of technology for load shedding process. Itika Sharma | Shavet Sharma"Load Shedding Management" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-2 | Issue-5 , August 2018, URL: http://www.ijtsrd.com/papers/ijtsrd18364.pdf http://www.ijtsrd.com/engineering/electrical-engineering/18364/load-shedding-management/itika-sharma
Shape memory alloys are metal alloys that can be deformed at one temperature but return to their original shape when heated or cooled. The most common alloys are nickel-titanium (Nitinol), copper-zinc-aluminum, and copper-aluminum-nickel. Nitinol was discovered in the 1960s and is now used widely in applications such as medical devices, aircraft, and household appliances. Shape memory alloys work through a solid state phase change between martensite and austenite phases - deforming occurs in the martensite phase while heating triggers shape recovery in the austenite phase. They provide advantages like biocompatibility and diverse applications but also
This study encapsulated equine endothelial progenitor cells and mesenchymal stem cells alone and in co-culture within a PEG-fibrinogen hydrogel scaffold to assess neovascularization. Equine EPCs formed tubules within 1 day when encapsulated alone or with MSCs, and vascularization increased over 4 days. Tubules did not form with MSCs alone. The hydrogel scaffold supported long-term cell viability and vascular structure formation, demonstrating its potential for tissue engineering and wound healing applications in horses. Future work will quantify vessel formation to determine scaffold thickness and MSC effects.
This document discusses corrosion resistant materials for extreme environments. It begins with an introduction that defines corrosion and extreme environments. It then reviews literature on the corrosion properties of various nickel alloys, high entropy alloys, and MCrAlY coatings. Next, it describes various corrosion resistant metals like stainless steels, nickel and aluminum alloys. It discusses recent developments in high entropy alloys and metal coatings. Finally, it provides two case studies on corrosion issues in nuclear power plants and gas turbine blades.
The Assembly Line and Mass Production Presentationerinlord
The assembly line and mass production transformed industry in the United States through increased efficiency, lower production costs, and higher profits. An assembly line divides the production process into sequential steps with different workers performing specialized tasks, allowing products like Ford's Model T to be mass produced. This innovation utilized unskilled labor, interchangeable parts, and mechanization to build custom products on a large scale, driving down costs and prices while increasing availability to consumers.
This document presents a rolling mechanism based piezoelectric vibration energy harvester. It begins with an introduction to energy harvesting, describing it as gathering energy from ambient sources like motion and converting it into electricity. It then discusses piezoelectric energy harvesting techniques and describes the basic structure of the rolling mechanism harvester. The harvester is designed to convert oscillating vibrations into rolling motion in order to amplify force and increase harvested energy output. Experimental results show the harvester is able to generate a stable DC voltage regardless of vibration frequency or amplitude.
Magnetorheological fluids are liquids that can change from liquid to solid when exposed to a magnetic field. They consist of magnetizable particles suspended in a carrier fluid like oil or water. As a magnetic field is applied, the particles form chains and structures that increase the fluid's viscosity and yield stress. MR fluids have applications in vehicle suspension dampers and transmissions where they allow precise control and fast response times to dampen vibrations or control torque transmission. Their properties can be controlled electronically and they require low power levels compared to similar smart fluids.
This document provides examples and uses of smart materials. It begins by defining smart materials as materials that react quickly to a stimulus in a specific manner. Examples given include materials that change color or shape in response to temperature, contact with water, electrical current, or light. Common uses of smart materials are in sensors, transducers, printers, and medical applications. Shape memory alloys, magnetorheological fluids, and thermochromic materials are also discussed along with various applications. The document concludes by mentioning some modern smart materials like thermochromic sheets, polymorphs, and quantum tunneling composites.
The document discusses the memristor, which is the fourth fundamental circuit element along with the resistor, capacitor, and inductor. A memristor is a two-terminal device whose resistance depends on the amount of electric charge that has passed through it. This allows it to remember the value of electric current or voltage over time. Memristors have potential applications for non-volatile memory and neuromorphic computing due to their ability to mimic synaptic behavior in neurons. However, challenges remain in developing memristor technology, including a lack of design standards and issues with heat dissipation during writing and reading.
This document is a project report submitted by 6 students for their Bachelor of Engineering degree. It describes the design and fabrication of a hydraulic sheet metal punching machine using leverage principles. The report contains 4 chapters that introduce hydraulics systems and components, describe punching machines, present the design of the machine parts, and include drawings of the machine assembly. It was guided by a professor and submitted to fulfill degree requirements.
DESIGN AND ANALYSIS OF COMPOSITE PISTON BY USING SOFTWAREvignesh waran
Composite materials are made from two or more materials combined to produce unique properties different from the individual components. Metal matrix composites (MMCs) consist of a metal matrix reinforced with ceramic particles or fibers. This chapter discusses MMCs made of a magnesium matrix reinforced with silicon carbide particles. It provides background on the materials, properties of magnesium, silicon carbide, and pistons. Design of MMCs involves modeling in CAD software, finite element analysis in ANSYS to simulate stresses and strains, and validating models through testing.
Lithium-ion batteries are rechargeable batteries commonly used in consumer electronics. They work by using lithium ions shuttling between the anode and cathode during charging and discharging. The lithium ions are inserted into and extracted from the crystalline structures of the electrode materials without changing their structure. This allows the batteries to be recharged many times. Some advantages of lithium-ion batteries are their high energy density, lack of memory effect, and lack of liquid electrolyte which prevents leaking. They are used widely in electric vehicles, power tools, and consumer electronics due to their lightweight and high voltage output.
Piezoelectric materials generate an electric charge when subjected to mechanical stress. They have applications in sensors, transducers, crystal oscillators, and energy harvesting from vibrations. Microwaves heat food by causing polar molecules like water to rotate rapidly and generate heat through dielectric heating. Superconductors enable applications like maglev trains, power cables, magnetic energy storage, particle accelerators, and medical imaging tools like MRI machines.
Magnets produce magnetic fields and attract ferromagnetic materials like iron. There are permanent magnets, which maintain their magnetism, and electromagnets, which are temporarily magnetic when near an electric current. The strongest permanent magnets are made from neodymium alloy and have high remanence and coercivity, allowing them to maintain strong magnetic fields.
THERMAL AND STRUCTURAL ANALYSIS OF AN EXHAUST MANIFOLD OF A MULTI CYLINDER EN...IAEME Publication
This document describes a thermal and structural analysis of an exhaust manifold for a multi-cylinder engine. A 3D model of the exhaust manifold was created in NX CAD software. Thermal analysis was performed to determine the temperature distribution, and coupled field analysis was conducted to calculate deflections and stresses under pressure and thermal loads. Modal analysis identified six natural frequencies between 0-1500Hz and their corresponding mode shapes. Harmonic analysis generated displacement-frequency graphs and calculated peak deflections and stresses at resonance frequencies. The analyses showed a maximum deflection of 0.1mm and Von Mises stress of 115MPa, below the yield strength, confirming the design can withstand operating loads.
This document discusses shape memory alloys (SMAs), specifically focusing on nickel-titanium (Ni-Ti) alloys. It defines SMAs as materials that can return to a predetermined shape after deformation through heating or cooling. SMAs exist in two phases, austenite and martensite, and transition between the phases through temperature changes, allowing the material to change shape. Common applications of Ni-Ti SMAs include uses in biomedical devices, robotics, and sensors due to properties like biocompatibility and high strain recovery. The document compares Ni-Ti SMAs to other materials like copper-based SMAs and stainless steel.
Organic electronics is a branch of electronics dealing with conductive polymers and small molecules. Conductive polymers are lighter, more flexible, and less expensive than inorganic conductors, making them desirable for many applications. Significant developments include the discovery that doping polyacetylene with iodine increases its conductivity by 12 orders of magnitude, and the invention of the organic light-emitting diode and organic photovoltaic cell. Organic electronics utilize carbon-based materials and offer advantages over traditional silicon-based electronics such as lower cost, mechanical flexibility, and lower processing temperatures.
Organic electronics is an emerging field with an unimaginable future.I have included nutshell of applications and future scope in this field.Think it will be helpful for engineering aspirants.
This document discusses using lead magnesium niobate-lead titanate (PMN-PT) for piezoelectric MEMS due to its giant piezoelectric properties. PMN-PT thin films were grown epitaxially on silicon substrates using a strontium titanate buffer layer. This resulted in atomically sharp interfaces and preserved the material's giant piezoelectric coefficients after microfabrication into cantilevers. Exploiting the high piezoelectric response of relaxor ferroelectrics like PMN-PT could enable smaller, more sensitive MEMS devices with lower power consumption.
This document discusses smart materials, specifically shape memory alloys. It defines smart materials as materials that can dramatically change properties in response to external stimuli like heat. Shape memory alloys are described as being able to "remember" their original shape when heated above a transition temperature. Examples of applications include orthodontic wires, eyeglass frames, and aircraft components. While smart materials show potential, issues like fatigue and cost need further study.
A memristor is a semiconductor device that can remember the amount of charge that has previously flowed through it. It was theorized in 1971 but was not physically realized until 2008. A memristor behaves similarly to a resistor but its resistance depends on the charge that has flowed through the circuit in the past. This "memory" property allows memristors to store information non-volatily without power, making them promising for applications like fast and efficient memory storage. However, memristor technology still needs improvements in areas like defect engineering and standard design rules before it can be commercially viable.
This slide describes the smart materials that are commonly used in civil engineering infrastructure like bridge, road, building etc for measurement of deflection, crack and seismic protection.
The memristor is a newly discovered passive circuit element that maintains a relationship between the electric charge and magnetic flux linkage. It acts as a variable resistor whose resistance depends on the amount of charge that has passed through it. Memristors can store data non-volatilely like flash memory but without requiring standby power. They have potential applications in low-power electronics, neural networks, analog computing and replacing transistors, which could dramatically change circuit design in the future as transistors did in the 20th century. The memristor was first theorized in 1971 and was experimentally realized in 2008 using a thin film of titanium dioxide.
Material Science - Short Answer Type Questions from AMIE ExamsAMIE(I) Study Circle
This document contains short questions and answers from AMIE exams on material science. It includes questions about stainless steel compositions, isomorphous systems, cold working of copper, definitions of remanence and coercivity in magnetic materials, TD nickel alloy containing thoria, and stress corrosion cracking in corrosive environments under tensile stress. The questions are followed by concise answers explaining the key concepts and terminology.
Shape memory alloys are smart materials that can remember their original shape and return to it when heated after being deformed. The most common shape memory alloys are nickel-titanium, copper-zinc-aluminum, and copper-aluminum-nickel alloys. Shape memory alloys exhibit the shape memory effect and pseudoelasticity/superelasticity, allowing deformation without permanent deformation. They have applications in orthodontics, aircraft components, civil structures, robotics and more due to their unique properties. Research continues to enhance shape memory alloy properties and develop new alloys.
Connecting Rods are practically generally used in all varieties of automobile engines. Acting as an
intermediate link between the piston and the crankshaft of an engine. It is responsible for transmission of the up
and down motion of the piston to the crankshaft of the engine, by converting the reciprocating motion of the
piston to the rotary motion of crankshaft. Thus, this study aims to carry out for the load, strain and stress analysis
of the crank end of the connecting rod of different materials. Based on which the High Strength Carbon Fiber
connecting rod will be compared with connecting rod made up of Stainless Steel and Aluminum Alloy. The
results can be used for optimization for weight reduction and for design modification of the connecting rod. Pro-E
software is used for modeling and analyses are carried out in ANSYS software. The results archived can also help
us identify the spot or section where chances of failure are high due to stress induced. Also the results obtained
can be used to modify the existing designs so that better performance and longer life cycle can be archived.
Keywords —Connecting Rod, Pro-E, FEA, ANSYS Workbench, Crank, Crankshaft, Piston, Carbon Fiber,
Stainless Steel, Aluminum Alloy.
This document summarizes the design project of a connecting rod made from either stainless steel or aluminum alloy. It analyzes the materials' chemical compositions, stresses and strains, safety factors, weight and stiffness, and fatigue life. Stainless steel was found to have lower deformation, higher safety factor and stiffness, and a longer fatigue life than aluminum alloy, but aluminum alloy is lighter. Stainless steel is also cheaper. The conclusion is that stainless steel is a better material for the connecting rod based on its performance characteristics.
The document discusses the memristor, which is the fourth fundamental circuit element along with the resistor, capacitor, and inductor. A memristor is a two-terminal device whose resistance depends on the amount of electric charge that has passed through it. This allows it to remember the value of electric current or voltage over time. Memristors have potential applications for non-volatile memory and neuromorphic computing due to their ability to mimic synaptic behavior in neurons. However, challenges remain in developing memristor technology, including a lack of design standards and issues with heat dissipation during writing and reading.
This document is a project report submitted by 6 students for their Bachelor of Engineering degree. It describes the design and fabrication of a hydraulic sheet metal punching machine using leverage principles. The report contains 4 chapters that introduce hydraulics systems and components, describe punching machines, present the design of the machine parts, and include drawings of the machine assembly. It was guided by a professor and submitted to fulfill degree requirements.
DESIGN AND ANALYSIS OF COMPOSITE PISTON BY USING SOFTWAREvignesh waran
Composite materials are made from two or more materials combined to produce unique properties different from the individual components. Metal matrix composites (MMCs) consist of a metal matrix reinforced with ceramic particles or fibers. This chapter discusses MMCs made of a magnesium matrix reinforced with silicon carbide particles. It provides background on the materials, properties of magnesium, silicon carbide, and pistons. Design of MMCs involves modeling in CAD software, finite element analysis in ANSYS to simulate stresses and strains, and validating models through testing.
Lithium-ion batteries are rechargeable batteries commonly used in consumer electronics. They work by using lithium ions shuttling between the anode and cathode during charging and discharging. The lithium ions are inserted into and extracted from the crystalline structures of the electrode materials without changing their structure. This allows the batteries to be recharged many times. Some advantages of lithium-ion batteries are their high energy density, lack of memory effect, and lack of liquid electrolyte which prevents leaking. They are used widely in electric vehicles, power tools, and consumer electronics due to their lightweight and high voltage output.
Piezoelectric materials generate an electric charge when subjected to mechanical stress. They have applications in sensors, transducers, crystal oscillators, and energy harvesting from vibrations. Microwaves heat food by causing polar molecules like water to rotate rapidly and generate heat through dielectric heating. Superconductors enable applications like maglev trains, power cables, magnetic energy storage, particle accelerators, and medical imaging tools like MRI machines.
Magnets produce magnetic fields and attract ferromagnetic materials like iron. There are permanent magnets, which maintain their magnetism, and electromagnets, which are temporarily magnetic when near an electric current. The strongest permanent magnets are made from neodymium alloy and have high remanence and coercivity, allowing them to maintain strong magnetic fields.
THERMAL AND STRUCTURAL ANALYSIS OF AN EXHAUST MANIFOLD OF A MULTI CYLINDER EN...IAEME Publication
This document describes a thermal and structural analysis of an exhaust manifold for a multi-cylinder engine. A 3D model of the exhaust manifold was created in NX CAD software. Thermal analysis was performed to determine the temperature distribution, and coupled field analysis was conducted to calculate deflections and stresses under pressure and thermal loads. Modal analysis identified six natural frequencies between 0-1500Hz and their corresponding mode shapes. Harmonic analysis generated displacement-frequency graphs and calculated peak deflections and stresses at resonance frequencies. The analyses showed a maximum deflection of 0.1mm and Von Mises stress of 115MPa, below the yield strength, confirming the design can withstand operating loads.
This document discusses shape memory alloys (SMAs), specifically focusing on nickel-titanium (Ni-Ti) alloys. It defines SMAs as materials that can return to a predetermined shape after deformation through heating or cooling. SMAs exist in two phases, austenite and martensite, and transition between the phases through temperature changes, allowing the material to change shape. Common applications of Ni-Ti SMAs include uses in biomedical devices, robotics, and sensors due to properties like biocompatibility and high strain recovery. The document compares Ni-Ti SMAs to other materials like copper-based SMAs and stainless steel.
Organic electronics is a branch of electronics dealing with conductive polymers and small molecules. Conductive polymers are lighter, more flexible, and less expensive than inorganic conductors, making them desirable for many applications. Significant developments include the discovery that doping polyacetylene with iodine increases its conductivity by 12 orders of magnitude, and the invention of the organic light-emitting diode and organic photovoltaic cell. Organic electronics utilize carbon-based materials and offer advantages over traditional silicon-based electronics such as lower cost, mechanical flexibility, and lower processing temperatures.
Organic electronics is an emerging field with an unimaginable future.I have included nutshell of applications and future scope in this field.Think it will be helpful for engineering aspirants.
This document discusses using lead magnesium niobate-lead titanate (PMN-PT) for piezoelectric MEMS due to its giant piezoelectric properties. PMN-PT thin films were grown epitaxially on silicon substrates using a strontium titanate buffer layer. This resulted in atomically sharp interfaces and preserved the material's giant piezoelectric coefficients after microfabrication into cantilevers. Exploiting the high piezoelectric response of relaxor ferroelectrics like PMN-PT could enable smaller, more sensitive MEMS devices with lower power consumption.
This document discusses smart materials, specifically shape memory alloys. It defines smart materials as materials that can dramatically change properties in response to external stimuli like heat. Shape memory alloys are described as being able to "remember" their original shape when heated above a transition temperature. Examples of applications include orthodontic wires, eyeglass frames, and aircraft components. While smart materials show potential, issues like fatigue and cost need further study.
A memristor is a semiconductor device that can remember the amount of charge that has previously flowed through it. It was theorized in 1971 but was not physically realized until 2008. A memristor behaves similarly to a resistor but its resistance depends on the charge that has flowed through the circuit in the past. This "memory" property allows memristors to store information non-volatily without power, making them promising for applications like fast and efficient memory storage. However, memristor technology still needs improvements in areas like defect engineering and standard design rules before it can be commercially viable.
This slide describes the smart materials that are commonly used in civil engineering infrastructure like bridge, road, building etc for measurement of deflection, crack and seismic protection.
The memristor is a newly discovered passive circuit element that maintains a relationship between the electric charge and magnetic flux linkage. It acts as a variable resistor whose resistance depends on the amount of charge that has passed through it. Memristors can store data non-volatilely like flash memory but without requiring standby power. They have potential applications in low-power electronics, neural networks, analog computing and replacing transistors, which could dramatically change circuit design in the future as transistors did in the 20th century. The memristor was first theorized in 1971 and was experimentally realized in 2008 using a thin film of titanium dioxide.
Material Science - Short Answer Type Questions from AMIE ExamsAMIE(I) Study Circle
This document contains short questions and answers from AMIE exams on material science. It includes questions about stainless steel compositions, isomorphous systems, cold working of copper, definitions of remanence and coercivity in magnetic materials, TD nickel alloy containing thoria, and stress corrosion cracking in corrosive environments under tensile stress. The questions are followed by concise answers explaining the key concepts and terminology.
Shape memory alloys are smart materials that can remember their original shape and return to it when heated after being deformed. The most common shape memory alloys are nickel-titanium, copper-zinc-aluminum, and copper-aluminum-nickel alloys. Shape memory alloys exhibit the shape memory effect and pseudoelasticity/superelasticity, allowing deformation without permanent deformation. They have applications in orthodontics, aircraft components, civil structures, robotics and more due to their unique properties. Research continues to enhance shape memory alloy properties and develop new alloys.
Connecting Rods are practically generally used in all varieties of automobile engines. Acting as an
intermediate link between the piston and the crankshaft of an engine. It is responsible for transmission of the up
and down motion of the piston to the crankshaft of the engine, by converting the reciprocating motion of the
piston to the rotary motion of crankshaft. Thus, this study aims to carry out for the load, strain and stress analysis
of the crank end of the connecting rod of different materials. Based on which the High Strength Carbon Fiber
connecting rod will be compared with connecting rod made up of Stainless Steel and Aluminum Alloy. The
results can be used for optimization for weight reduction and for design modification of the connecting rod. Pro-E
software is used for modeling and analyses are carried out in ANSYS software. The results archived can also help
us identify the spot or section where chances of failure are high due to stress induced. Also the results obtained
can be used to modify the existing designs so that better performance and longer life cycle can be archived.
Keywords —Connecting Rod, Pro-E, FEA, ANSYS Workbench, Crank, Crankshaft, Piston, Carbon Fiber,
Stainless Steel, Aluminum Alloy.
This document summarizes the design project of a connecting rod made from either stainless steel or aluminum alloy. It analyzes the materials' chemical compositions, stresses and strains, safety factors, weight and stiffness, and fatigue life. Stainless steel was found to have lower deformation, higher safety factor and stiffness, and a longer fatigue life than aluminum alloy, but aluminum alloy is lighter. Stainless steel is also cheaper. The conclusion is that stainless steel is a better material for the connecting rod based on its performance characteristics.
The document summarizes research conducted to optimize the design of a connecting rod for a vehicle engine. The connecting rod was modeled using Pro-E software and analyzed using ANSYS to compare stresses and strength between the original aluminum design and an optimized design made of PEEK composite material. The analysis found the PEEK design reduced weight by approximately 46.7% while improving strength, with von Mises stress reduced by 0.18% and factor of safety increased by 23.76%. The optimized connecting rod design demonstrated improvements in weight and strength.
The document describes the mechanical design of a connecting rod for a Ferrari F136 F engine. An analytical load analysis was performed using MATLAB to determine loads on the connecting rod. A beam theory analysis found maximum stresses and buckling safety factors. A preliminary 2D design was modeled and analyzed using finite element analysis in COMSOL, finding a yield safety factor of 1.19. Design iterations increased this to 2.62 and improved fatigue life. A final 3D model analyzed in Abaqus yielded a safety factor of 1.97 against static yield.
DESIGN AND ANALYSIS OF CONNECTING ROD USING ALUMINIUM ALLOY 7068 T6, T6511 IAEME Publication
The connecting rod is the intermediate member between the piston and the Crankshaft. Its primary function is to transmit the push and pull from the piston pin to the crank pin, thus converting the reciprocating motion of the piston into rotary motion of the crank. This thesis describes designing
and Analysis of connecting rod. Currently existing connecting rod is manufactured by using Forged steel. In this drawing is drafted from the calculations.
3D Scanning and Digitizing
Exascan.is The High Resolution Scanner From The Handyscan 3d Line
Of Truly Portable, Self Positioning Handheld Laser Scanners By
Creaform.
Examines Every Details
The Exascan Selfpositioning Handheld Scanner Offers Increased
Resolution And Accuracy.
Exact 3d Representation
The Exascan Makes It Possible To Carry Out Exact 3d Scanning
Projects With A Level Of Detail And Accuracy That No Other Handheld
Scanning System Can Achieve.
The Exascan Is Definitely The Most Flexible, Free form Inspection
Device On The Market.applications And Solutions.
Reverse Engineering & Styling, Design & Analysis
Get Best Quote 1. Include 3D scanning of existing objects
2. 3D archiving
3. Complex shape acquisition
4. Damage assessment
5. Clay model digitizing
6. Facilitates surface reconstruction
7. Class A surfacing
8. 3D modelling
9. Mockups
10. Packaging design
11. Rapid prototyping.
12. Mechanical design (tooling & jigs, maintenance, repair &
overhaul)
Inspection
1. Noncontact inspection
2. First article inspection
3. Supplier quality inspection
4. ParttoCAD inspection (2D INSPECTION)
5. Conformity assessment of 3D models against the original
parts/production tooling
6. Conformity assessment of manufactured parts against originals
Static Stress Analysis of Connecting Rod Using Finite Element ApproachIOSR Journals
Every vehicle which equipped with internal combustion engine requires connecting rod. In this paper a static stress analysis of connecting rod made up of SS 304 used in Cummins NTA 885 BC engine is conducted, using finite element method. After measuring the dimension of connecting rod, model is developed in CATIA V5 software and imported to ANSYS WORKBENCH 14.0 software. Static analysis is done by fixing the smaller end and load is applied at bigger end of connecting rod. Stress developed at four different sections is used for analysis. Maximum stress point and section prone to failure is finding out by this analysis. Graph between stress and load is plotted at section prone to failure and result of stress analysis is shown with the help of image.
This document is a thesis submitted by Pravardhan S. Shenoy to the University of Toledo in partial fulfillment of a Master of Science degree in Mechanical Engineering. The thesis, advised by Dr. Ali Fatemi, involves dynamic load analysis and optimization of a connecting rod. The study performs load analysis on the connecting rod to determine dynamic loads over time. Finite element analysis is conducted under quasi-dynamic and static loads. The connecting rod is then optimized for weight and cost subject to constraints like fatigue life.
Design and Construction of a Connecting rodFaisal Niloy
The document describes the design and construction of a connecting rod. It begins with the objectives of studying the connecting rod, understanding its function, designing it using CAD, and constructing a physical model. It then provides an introduction to connecting rods, explaining that they connect the piston to the crankshaft and transmit reciprocating motion to rotational motion. The document discusses different manufacturing processes for connecting rods and compares technologies. It presents the design process for the connecting rod, showing calculations for dimensions. Finally, it includes the CAD model and photos of the constructed physical connecting rod.
Group 3's presentation discusses the manufacturing of connecting rods. It compares the forging and casting processes, outlining the advantages of forging such as higher dimensional accuracy, lower costs for high production volumes, and smoother engine running. The presentation then details the specific forging and machining steps used to manufacture connecting rods, including heating, piercing, trimming, shot peening, fracturing, assembly, and inspection. Limitations discussed include the need for an environmentally friendly process and cost-effective finished product with limited mass deviation. Forging is considered more economical than casting for production volumes above 20,000 pieces.
Stress Analysis of I.C.Engine Connecting Rod by FEM and PhotoelasticityIOSR Journals
Abstract: The automobile engine connecting rod is a high volume production critical component. Every vehicle
that uses an internal combustion engine requires at least one connecting rod .From the viewpoint of
functionality, connecting rods must have the highest possible rigidity at the lowest weight. The major stress
induced in the connecting rod is a combination of axial and bending stresses in operation. The axial stresses are
produced due to cylinder gas pressure (compressive only) and the inertia force arising in account of
reciprocating action (both tensile as well as compressive), where as bending stresses are caused due to the
centrifugal effects. The result of which is, the maximum stresses are developed at the fillet section of the big and
the small end.Hence, the paper deals with the stress analysis of connecting rod by Finite Element Method using
Pro/E Wildfire 4.0 and ANSYS WORKBENCH 11.0 software. The comparison and verification of the results
obtained in FEA is done experimentally by the method of Photo elasticity(Optical Method). The method of
Photoelasticity includes the casting of Photoelastic sheet using Resin AY103 and Hardner HY951, preparation
of the model from Photoelastic sheet calibration of the sheet to determine material fringe value.
Keywords - Big End fillet section ,Connecting Rod, Compressive Stresses , Failure of Connecting Rod, FEA,
Photoelasticity, Small End fillet section, Tensile Stresses.
Modeling and Analysis of Two Wheeler Connecting Rod by Using AnsysIOSR Journals
Connecting rod is a major link inside of a internal combustion engine. It is the intermediate member
between the piston and the crankshaft. Its primary function is to transmit the push and pull from the piston pin
to the crank pin thus converting the reciprocating motion of piston in to rotary motion of the crank. In this paper
a static analysis is conducted on a connecting rod of a single cylinder 4-stroke petrol engine. The model is
developed using Solid modeling software i.e. PRO/E (creo-parametric). Further finite element analysis is done
to determine the von-misses stresses shear stress and strains for the given loading conditions.
STRESS LIFE BASED FATIGUE ANALYSIS ON AUTOMOTIVE CONNECTING RODVishnu R
This document summarizes the setup and results of a static structural analysis and fatigue analysis performed on a connecting rod model (A4). The model includes the geometry, mesh, materials, loads, and boundary conditions. The static structural analysis calculates stress, strain, and deformation results. Two fatigue analyses are then performed to calculate fatigue life, safety factors, and damage based on the static results and a load history file. Charts of fatigue sensitivity and rainflow/damage matrices are presented.
This document summarizes a study that evaluated the design of an automobile connecting rod using finite element analysis to optimize it for high cycle fatigue strength. The study developed a 3D model of a connecting rod, analyzed stresses under different loading conditions using FEA software, and identified areas of high stress concentration. Six different load cases were considered for the analysis, including bolt preload, inertial forces at various engine speeds, and combined gas and inertial forces. The maximum and minimum bolt preloads were identified as critical parameters for the high cycle fatigue analysis. The study aimed to establish a systematic procedure to evaluate and optimize connecting rod design for fatigue life using finite element modeling.
A Project Submitted to the Materials Engineering Department / University of Technology (Baghdad -Iraq )in partial fulfillment of the requirements for the degree of b.sc in Materials Engineering
Analysis and Structural Optimization of a Mechanical Component for the Heavy ...Alessandro Musu
This document presents an introduction to structural optimization. It discusses how structural optimization aims to design mechanical components to best withstand applied loads by minimizing weight or maximizing stiffness, while satisfying constraints. It outlines the typical formulation of a structural optimization problem, including defining an objective function and design variables. Two main topology optimization methods are described: minimum compliance design and bi-directional evolutionary structural optimization (BESO). The document also introduces the software Inspire, which will be used to conduct a practical structural optimization example of a mechanical component for the heavy industry sector in the subsequent chapters.
This document discusses corrosion control engineering for gas pipelines. Corrosion causes degradation of pipeline materials over time. Two main methods for mitigating corrosion are protective coatings and cathodic protection using sacrificial anodes. Various tests are performed on coating materials to evaluate properties like strength, density, and volatile content. Proper coating selection and corrosion protection techniques can help minimize corrosion and extend pipeline lifespan, but factors like material type, location, and costs must be considered. The goal is to harness the adverse effects of corrosion to safely deliver gas to customers.
This document discusses corrosion control engineering and summarizes various techniques used to mitigate corrosion in gas pipelines. It describes how corrosion occurs via electrochemical reactions between the pipe material and the surrounding environment. Common mitigation methods used by SNGPL include protective coatings and cathodic protection using sacrificial anodes. The document then summarizes various tests and equipment used to inspect coatings, such as tests to evaluate properties of primers, coatings, and anodes used in corrosion protection systems.
Avoidance of Thermal Damage During Grinding.Shaun Edwards
This document provides details about a student project examining two thermal models for avoiding thermal damage during grinding. It includes an abstract, acknowledgements, nomenclature, and outlines the introduction, research, methodology, expected results, discussion and conclusion sections. The introduction discusses the importance of avoiding thermal damage in grinding and the aims of comparing existing thermal models against experimental data to identify an improved model.
A design for a car park barrier was created using Solidworks to withstand wind speeds up to 105MPH and have an actuation cycle life of over 107 cycles. Initial hand calculations determined stresses from self-weight and wind loads. These identified maximum stresses of 80MPa for the boom arm and 398MPa for the motor shaft. An intentionally weak material was selected to initially fail the design. Subsequent FEA analysis and material selection iterations were performed to optimize the design, validating it could withstand the required loads with suitable safety factors.
Experimental investigation of the crashworthiness performance of laminated co...IRJET Journal
This document presents the results of an experimental investigation into the crashworthiness performance of laminated composites made of CPVC pipe and woven carbon fiber mat. Crashworthiness indicators like energy absorption, specific energy absorption, maximum force, mean crushing force, and crushing force efficiency were used to evaluate the performance of test specimens under compression loading. Specimens with increasing numbers of carbon fiber mat laminations were tested and compared to an unreinforced CPVC pipe specimen. Both experimental and finite element analysis results showed that additional carbon fiber laminations led to decreased deformation and increased crushing force efficiency when subjected to the same load, indicating improved crashworthiness performance. The finite element analysis results from ANSYS software agreed with the trends observed in
This document is a thesis submitted by Andrew Bell for the degree of Masters of Science in Mechanical Engineering at the University of Toronto. The thesis investigates the design of a catalytic combustor to burn pure methanol or waste gas from a high-temperature proton exchange membrane fuel cell for heat. Key parameters affecting fuel-air premixing and their impact on temperature distribution and emissions are examined. The experimental setup includes a moveable block swirl generator, evaporator, mixing chamber, catalytic monolith module, and sensors to analyze performance. Results are discussed to evaluate the design and combustion characteristics.
The document summarizes the internship report of Imtiaz Ahmed at United Refrigeration Industries Limited Dawlance (URIL-Dawlance). It discusses the objectives of familiarizing with the industrial processes and covers the key production departments - plastic moulding, sheet metal works, painting, pre-forming and forming. It also describes the quality control processes to ensure customer specifications are met. The internship provided valuable insights into refrigeration manufacturing and will help in future career preparation.
The document discusses the design of a simulant solution to model the non-Newtonian viscosity behavior of coatings. Various combinations of clay and polyethylene glycol (PEG) in water were tested. A solution of 2.2% clay and 0.25% PEG with a cure time of 64 hours was found to best match the target non-Newtonian behavior, falling within the desired ranges for consistency index (m value) and recovery gap (R value). The simulant solution aims to replicate the shear thinning and thixotropic properties of coatings to enable further mixing studies.
This thesis examines the development of a carbon fiber-stainless steel laminate composite material. The goal is to improve the bearing strength of carbon fiber composites by adding thin stainless steel strips. The author conducts preliminary tests on different laminate configurations to determine optimal production methods. Initial and final bearing tests are then performed to evaluate how the steel additions affect bearing strength. The results confirm that bearing strength can be improved by adding steel strips, but the effect depends on the specific steel and composite used. Cross-ply laminates perform better than uni-directional ones. While steel increases weight, benefits are seen for thicker laminates experiencing high loads, as thickness reductions over 35% are possible without adding weight. The main findings are
Design and Analysis of Composite CylinderIRJET Journal
This document describes the design and analysis of a composite cylinder using ANSYS software. It begins with an introduction to pressure vessels and the benefits of using composite materials instead of steel, including lower weight. It then details the modeling and analysis process in ANSYS to optimize the winding angle and thickness of the composite cylinder. The results of the ANSYS analysis are compared to experimental data and the structural efficiency of the composite cylinder is evaluated against a steel cylinder of the same dimensions.
The document describes the design, manufacturing and testing of a steam-powered model car for educational purposes. Key points:
- A steam engine was designed and built using CAD software and various manufacturing methods like machining and 3D printing.
- Components included a boiler, firebox, piston, cylinder and model car chassis. Testing evaluated the boiler's ability to withstand pressure and the engine's function.
- The finished model provides a hands-on teaching tool for students to apply thermodynamics and engineering calculations from lectures. Testing validated the design's ability to safely demonstrate steam engine operations and calculations.
The motivation behind the project and research is to present a new characteristic for temperature profile estimation in modelling of Rotary Friction Welding Process. For the first time, a unified model has been exhibited, with an implementation of phase transformation of similar and dissimilar materials and plastics too. The model was generated on ANSYS 15.0, thermal and structural modules were used to plot the temperature curve with which I make a compression. The curve for welding of dissimilar metals was analyzed with that of practical curves already acquired and then the effect of varying parameters on the welding of similar metals was studied.
Prepreg technology has enabled the evolution of high-speed transportation like trains and ships. This document explains prepreg technology, including how prepregs are made and their properties. Prepregs consist of fibers reinforced with a resin or matrix. They are used in aerospace, marine, sports, and other industries due to benefits like lower weight, higher strength and stiffness than conventional materials. Common prepreg processing methods include vacuum bagging and autoclaving.
This thesis examines modifications to transformer design to reduce temperature rise. The thesis identifies causes of heat generation in transformer windings and cores. It also discusses methods to reduce heat generated and dissipate heat efficiently. A prototype transformer is designed and tested based on the optimal design. Test results show the modifications successfully reduced heat losses and temperature rise compared to the existing design, which will slow insulation deterioration and increase transformer lifespan.
This document describes the design and fabrication of a wear test specimen die for metal matrix composite materials. It provides details of the project, including the equipment used for wear testing, die specifications designed using NX8 software, test specimen dimensions based on ASTM standards, the material selection and properties of oil hardened non-shrinking steel chosen for the die material, and the manufacturing processes employed to produce the die including casting, machining operations and electric discharge machining. The goal of the project is to produce a die that can be used to test the wear behavior of metal matrix composites.
1. The intern analyzed the microstructure, mechanical properties, and chemical composition of thermo-mechanically tempered (TMT) bars and hot rolled coil produced by Jindal Steel Works.
2. For TMT bars, the intern examined samples of 25mm and 40mm diameter bars and found the thickness of the martensite ring depended on bar diameter. Microstructures showed ferrite and pearlite in the core and bainite and tempered martensite at the outer rings.
3. For hot rolled coil, the intern compared samples with normal and excess nitrogen levels. Preliminary results showed excess nitrogen was associated with higher yield strength, ultimate tensile strength, and finer grain size due to
The document discusses the role and responsibilities of a piping material engineer. A piping material engineer is responsible for developing piping classes, writing specifications, maintaining valve and component data sheets, and interacting with other engineering disciplines. Key responsibilities include selecting materials of construction, reviewing vendor documentation, and ensuring piping systems meet design requirements. Experience in multiple areas such as design, construction, corrosion and welding is important for a piping material engineer.
This document reviews impression die forging. It discusses how computer aided engineering techniques are used to optimize die design to improve accuracy and reduce costs. The document summarizes existing die design techniques and approaches to develop an optimal system. Impression die forging can produce parts with high complexity from various metals at moderate costs. The document also discusses common materials used in closed die forging like steel, aluminum, and copper, as well as advantages like net shapes, high strength, and close tolerances and disadvantages like high tooling costs and size limitations.
Similar to 1_Gillan Michael Mid Module Report (20)
1. Optimisation of a Connecting Rod of an Internal
Combustion Engine
AUTHOR
Michael Gillan
A THESIS SUBMITTED FOR THE DEGREE OF BACHELOR OF ENGINEERING
(HONOURS) IN MECHANICAL ENGINEERING, AT THE SCHOOL OF
ENGINEERING, GALWAY-MAYO INSTITUTE OF TECHNOLOGY, IRELAND
SUPERVISOR
Laurentiu Dimache
DEPARTMENT OF MECHANICAL & INDUSTRIAL ENGINEERING,
GALWAY-MAYO INSTITUTE OF TECHNOLOGY, IRELAND
SUBMITTED TO THE GALWAY-MAYO INSTITUTE OF TECHNOLOGY
Date: 2/05/2014
2. ii
DECLARATION OF ORIGINALITY
May, 2014
The substance of this thesis is the original work of the author and due reference and
acknowledgement has been made, when necessary, to the work of others. No part of this
thesis has been accepted for any degree and is not concurrently submitted for any other
award. I declare that this thesis is my original work except where otherwise stated.
_________________________
Michael Gillan
4. iv
Abstract
An optimisation study was performed on a forged steel connecting rod to reduce the
weight, manufacturing and material costs. A static analysis was performed to analyse the
stress concentration from the tensile and compressive forces using Ansys 14.5 finite
element analysis.
The main analysis considered buckling, fatigue and static analysis. The connecting rod was
modelled and analysed to find the highest points of stress which was at the top of the shank
at the fillet. The area to be considered for the weight reduction was the shank as this was
the most critical part of the connecting rod, this reduced the weight of the connecting rod
by 9.38 percent.
Various size fillets were applied at the top of the shank to find the most suitable fillet to
reduce stress. The 10mm fillet was the most optimum as it reduced the stress the most, and
the factor of safety was increased by more than fifty percent. CES Materials was used to
find a material with the best properties of fatigue, density, cost, tensile and compressive
strength.
The material with the best properties was the low alloy steel. The connecting rod was
analysed using different materials within Ansys and the low alloy steel reduced the stress
in tension at all locations of the connecting rod, but the 15mm fillet produced better results
at the lower part of the shank. Overall the low alloy steel reduced the stress the most and
would be the most suitable material.
The manufacturing was also considered, using CES Materials to compare manufacturing
methods of cost, surface finish and setup cost. Forging and powder metallurgy were the
two best methods but powder metallurgy produced a better surface finish and including
fracture splitting this would be the cheapest option.
5. v
Acknowledgements
I would like to thank Mr Laurentiu Dimache for his guidance and support given throughout
the year.
I would also like to thank Co supervisor Dr Gerard Mac Michael for his guidance from the
presentation.
I would also like to thank all the lecturers within GMIT for their guidance and support
throughout the year.
I would also like to thank family and friends for their support throughout the past year.
6. vi
Glossary
IC…………………………………....Internal Combustion Engine
RPM………………………………....Revolutions per Minute
FEA……………………………….....Finite Element Analysis
FI………………………………….....Failure Index
ABDC………………………………..After bottom dead Centre
ATDC………………………………..After Top Dead Centre
BBDC………………………………..Before Top Dead Centre
BDC……………………………...….Bottom Dead Centre
TDC……………………………...….Top Dead Centre
FI…………………………………….Failure Index
FEA………………………………….Finite Element Analysis
FOS………………………………….Factor of Safety
7. vii
Symbols
Symbol Unit Description
˚C Degrees Celsius Temperature
K Kelvin Temperature
N Newton Force
Kg Kilogram Mass
M Metre Length
S Second Time
Pa Pascal Pressure
Ω Rad/Second Angular Velocity
Ρ Density Mass per Volume
Phi Degree
R Radius Degree
L Length Metre
W Kg Mass
E GPa Youngs Modulus
ε Poissons Ratio Ratio
Se MPa Endurance strength
Se’ MPa Endurance strength
Ka Percent Surface finish
Kb Percent Size factor
Kc Percent Reliability
Kd Percent Temperature
Ke Percent Stress concentration
10. x
TABLE OF FIGURES
FIGURE 2-1: DIAGRAM OF A STEAM ENGINE (STEAM ENGINE TERMINOLOGY AND OPERATING PRINCIPLES MAY
2011)......................................................................................................................................................... 4
FIGURE 2-2: DIAGRAM OF A TWO STROKE ENGINE PROCESS (TWO STROKE ENGINE EXHAUST NOVEMBER 2013).. 5
FIGURE 2-3: EXPANSION CHAMBER OF A TWO STROKE ENGINE (TWO STROKE ENGINE EXHAUST NOVEMBER 2013)
.................................................................................................................................................................. 6
FIGURE 2-4: DIAGRAM OF A FOUR STROKE ENGINE (TWELVE BUDGET OUTPUT FOUR STROKE DIAGRAM, 2013). 7
FIGURE 3-1: DIAGRAM OF A CONNECTING ROD (LUKE SCHREIER, 1999)............................................................ 9
FIGURE 3-2 I-BEAM CONNECTING ROD (R&R RACING PRODUCTS CURRENT CATALOGUE)............................... 12
FIGURE 3-3 H-BEAM CONNECTING (ROD R&R RACING PRODUCTS CURRENT CATALOGUE) ............................. 12
FIGURE 3-4: LOCATION OF STRESSES (PRAVARDHAN S ET AL, 2005) ............................................................... 13
FIGURE 3-5: VON MISES STRESS DISPLACEMENT OF ROD UNDER TENSILE LOADING USING FAILURE INDEX FEA
(PRAVARDHAN S. ET AL 2005) ................................................................................................................ 14
FIGURE 3-6: VON MISES STRESS DISPLACEMENT OF ROD UNDER TENSILE LOADING USING FAILURE INDEX FEA,
FE MODEL WITH SPRINGS TO THE RIGHT (SHENOY. ET AL 2005).............................................................. 15
FIGURE 3-7: EFFECTS OF BUCKLING TO A CONNECTING ROD (MOON KYU LEE A, HYUNGYIL LEE A,*, TAE SOO
LEE A, HOON JANG, 2010)....................................................................................................................... 16
FIGURE 4-1 ENGINE ASSEMBLY ....................................................................................................................... 20
FIGURE 4-2: FLOW CHART FOR REDESIGN PROCESS OF THE CONNECTING ROD............................................... 21
FIGURE 4-3: RENDERED MODEL OF THE CRANKSHAFT, CONNECTING RODS AND PISTONS................................. 23
FIGURE 4-4 CONNECTING ROD ASSEMBLY AND MODEL OF CONNECTING ROD FROM CREO PARAMETRIC......... 24
FIGURE 4-5: DIAGRAM OF CRANKSHAFT, CONNECTING ROD AND PISTON......................................................... 26
FIGURE 4-6: FREE BODY DIAGRAM OF CRANKSHAFT (R).................................................................................. 27
FIGURE 4-7: FREE BODY DIAGRAM OF CONNECTING ROD ................................................................................. 28
FIGURE 4-8: VELOCITY AND ACCELERATION GRAPHS (NORTON, R.L., 2003)................................................ 29
FIGURE 4-9: DIMENSIONS OF THE CRANK PIN ................................................................................................... 33
FIGURE 4-10: SECTION A-A FATIGUE .............................................................................................................. 34
FIGURE 4-11: PRESSURE DISTRIBUTION OVER THE SURFACE OF A PIN (WEBSTER ET AL, 1983)......................... 37
FIGURE 4-12: PRESSURE APPLIED TO AREA 2.................................................................................................... 38
FIGURE 4-13: BOUNDARY CONDITIONS ............................................................................................................ 38
FIGURE 4-14: MESH REFINEMENT .................................................................................................................... 39
FIGURE 4-15: YOUNGS MODULUS /DENSITY VS PRICE..................................................................................... 41
FIGURE 4-16: COMPRESSIVE STRENGTH VS FATIGUE STRENGTH...................................................................... 41
FIGURE 4-17: TENSILE STRENGTH VS FATIGUE STRENGTH ............................................................................... 42
FIGURE 4-18: ECONOMIC BATCH SIZE VS RELATIVE EQUIPMENT COST ............................................................. 43
FIGURE 4-19: ROUGHNESS VS RELATIVE COST INDEX....................................................................................... 44
FIGURE 4-20: TOOLING COST ........................................................................................................................... 44
11. xi
FIGURE 5-1: STRESS LOCATIONS ...................................................................................................................... 45
FIGURE 5-2: VON MISES STRESS 5MM FILLET (TENSION) ................................................................................ 46
FIGURE 5-3: VON MISES STRESS 7MM FILLET (TENSION) ................................................................................. 47
FIGURE 5-4: VON MISES STRESS 10MM FILLET (TENSION) ............................................................................... 48
FIGURE 5-5: VON MISES STRESS 15MM FILLET (TENSION) ............................................................................... 49
FIGURE 5-6: STRESS LOCATION POINTS ............................................................................................................ 50
FIGURE 5-7: VON MISES STRESS 5MM FILLET (COMPRESSION) ........................................................................ 50
FIGURE 5-8: VON MISES STRESS 7 MM FILLET COMPRESSION........................................................................... 51
FIGURE 5-9: VON MISES STRESS 10 MM FILLET COMPRESSION......................................................................... 52
FIGURE 5-10: VON MISES STRESS 15 MM FILLET COMPRESSION....................................................................... 53
FIGURE 5-11: RESULTS OF 5, 7, 10 AND 15 MM FILLETS, COMPRESSION AND TENSION ..................................... 54
FIGURE 5-12: DISPLACEMENT WITH COMPRESSIVE LOAD................................................................................. 55
FIGURE 5-13: DISPLACEMENT WITH LOAD IN TENSION..................................................................................... 55
FIGURE 5-14: FACTOR OF SAFETY COMPRESSION ............................................................................................. 56
FIGURE 5-15: FACTOR OF SAFETY TENSION ..................................................................................................... 57
FIGURE 5-16: COMPARISON OF MATERIALS...................................................................................................... 58
FIGURE 5-17: ORIGINAL CONROD AND OPTIMISED CONROD ............................................................................. 59
FIGURE 10-1: CONNECTING ROD ASSEMBLY (FRONT VIEW AND SIDE VIEW)..................................................... 67
FIGURE 10-2: CONNECTING ROD AND CAP DISASSEMBLY ................................................................................ 67
FIGURE 10-3: CONNECTING ROD CAP FRONT AND SIDE VIEW ........................................................................... 68
FIGURE 10-4: PISTON AND GUDGEON PIN......................................................................................................... 68
FIGURE 10-5: CRANKSHAFT ............................................................................................................................. 69
FIGURE 10-6: VOLUME OF ORIGINAL CONNECTING ROD AND OPTIMISED CONROD ........................................... 69
FIGURE 11-1: ORIGINAL CROSS SECTIONAL AREA OF SHANK (MD SOLIDS)...................................................... 70
FIGURE 11-2: MOMENT OF INERTIA Y-AXIS (ORIGINAL CONNECTING ROD)...................................................... 70
FIGURE 11-3: MOMENT OF INERTIA Z-AXIS (ORIGINAL CONNECTING ROD)...................................................... 71
FIGURE 11-4: MODIFIED CROSS SECTIONAL AREA (MD SOLIDS)...................................................................... 71
FIGURE 11-5: MOMENT OF INERTIA AND AREA Y-Y AXIS (MODIFIED CONROD)............................................... 72
FIGURE 11-6: AREA VS CRITICAL LOAD........................................................................................................... 72
FIGURE 13-1: STRESS CONCENTRATION Q ........................................................................................................ 80
FIGURE 13-2: STRESS CONCENTRATION KT...................................................................................................... 80
FIGURE 13-3: SURFACE FACTOR KA ................................................................................................................. 81
FIGURE 13-4: RELIABILITY FACTOR ................................................................................................................. 81
FIGURE 13-5: VON MISES STRESS LOW ALLOY STEEL COMPRESSION AND TENSILE .......................................... 82
FIGURE 13-6: VON MISES STRESS MEDIUM CARBON STEEL COMPRESSION AND TENSION ................................ 83
FIGURE 13-7: VON MISES STRESS HIGH CARBON STEEL COMPRESSION AND TENSION..................................... 84
FIGURE 13-8: VON MISES STRESS TITANIUM STEEL COMPRESSION AND TENSION ........................................... 85
12. xii
Table of Tables
TABLE 3-1: LIST OF MATERIALS USED FOR GENERAL AUTOMOTIVE USE (MICHAEL F 1988) ............................. 10
TABLE 3-2: MATERIALS USED FOR HIGH PERFORMANCE CONNECTING RODS (MICHAEL F 1988) ...................... 11
TABLE 3-3: TITANIUM ALLOY COMPARED TO PF-11C50/60 STEELS (J.W. QIU A ET AL, 2012) ........................ 11
TABLE 4-1: TECHNICAL INFORMATION OF THE ENGINE (KAWASAKI ZX 7R 96-03 SERVICE MANUAL) ................ 25
TABLE 4-2 MATERIAL PROPERTIES OF THE ORIGINAL CONNECTING ROD.......................................................... 25
TABLE 4-3: MATERIAL PROPERTIES OF EACH MATERIAL .................................................................................. 34
TABLE 4-4: CONSTRAINTS APPLIED CES MATERIALS ...................................................................................... 40
TABLE 4-5: LIMITS APPLIED IN CES MATERIALS ............................................................................................. 43
TABLE 5-1: LOCATION OF STRESS, FOS AND DISPLACEMENT (5 MM FILLET) ................................................... 46
TABLE 5-2: LOCATION OF STRESS, FOS AND DISPLACEMENT (7 MM FILLET).................................................... 47
TABLE 5-3: LOCATION OF STRESS, FOS AND DISPLACEMENT (10 MM FILLET).................................................. 48
TABLE 5-4: LOCATION OF STRESS, FOS AND DISPLACEMENT (15MM FILLET) .................................................. 49
TABLE 5-5: LOCATION OF STRESS, FOS AND DISPLACEMENT (5MM FILLET) .................................................... 50
TABLE 5-6: LOCATION OF STRESS, FOS AND DISPLACEMENT (7 MM FILLET).................................................... 51
TABLE 5-7: LOCATION OF STRESS, FOS AND DISPLACEMENT (10 MM FILLET).................................................. 52
TABLE 5-8: LOCATION OF STRESS, FOS AND DISPLACEMENT (15 MM FILLET).................................................. 53
TABLE 5-9: STATIC FACTOR OF SAFETY 7 AND 10MM FILLET .......................................................................... 57
TABLE 5-10: FATIGUE CYCLES AND COST VS MATERIAL .................................................................................. 59
TABLE 13-1: REACTION FORCES COMPRESSION................................................................................................ 77
TABLE 13-2: REACTION FORCES TENSION ........................................................................................................ 77
TABLE 13-3: PERCENTAGE ERROR (TENSION) .................................................................................................. 78
TABLE 13-4: PERCENTAGE ERROR (COMPRESSION).......................................................................................... 79
13. 1
1. Introduction
The connecting rod has to withstand dynamic forces from the axial motion of the piston
and the rotational motion of the crankshaft. The connecting rod of an internal combustion
engine is considered a crucial part of the engine. Literature suggests many different
methods of optimization of a connecting rod. (Lee a et al, 2010) states that buckling is to
be considered when reducing the size of the shank, but (Shenoy et al, 2005) states fatigue
strength is a critical factor compared to the static and buckling resistance. (Shenoy et al,
2005) used quasi dynamics to analyse crack growth of the material while in motion.
(Mirehei et al, 2008) states that stress concentration factors can be used to calculate the life
span of the connecting rod. (Shenoy, 2004) states the minimum factor of safety should be
three. Due to the development of Finite element analysis it has become easier and cheaper
to develop stronger and lighter connecting rods.
The material properties needs to be suitable for the tensile and compressive forces applied,
materials widely used in vehicles today use various types such as medium carbon steel,
alloy steel and in some circumstances titanium which is mainly used in competition use.
(Qui J.W et al, 2012) states the relative density of the material has an impact to the
mechanical properties. A relative new material C70 steel can be used in the fracture split
process at room temperature. This method has a thirty percent cost reduction of the
manufacturing process.
(Michael F, 1988) states that near net shape from powder metallurgy results in less
machining as compared to forging. The forging process removes any abnormalities within
the steel due the blows exerted on the steel.
Research Objective
The objective of this project is to analyse the connecting rod using FEA software to predict
cause of failure, reduce weight and choose the best material and manufacturing process.
14. 2
Aims
The aim of the project is to analyse the connecting rod and to reduce stress concentration
using FEA. This will involve researching literature to see what methods were successful
and not so successful.
Project overview
Chapter 2 and 3 reviews research from literature to see what has been done, and will be
used to define the best approach to the project. Also in this chapter will be a discussion of
different materials and manufacturing methods.
Chapter 4 shows the analysis to the project and how the analysis was approached.
Chapter 5 shows the results and finds the most suitable fillet and material to increase the
fatigue life and factor of safety.
Chapter 6 will discuss the results and which method worked best.
Chapter 7 will discuss the overall project and discuss success and failures throughout the
project.
15. 3
2. Literature review
This chapter will be discussing the history of the combustion engine and looking at
different methods used in reducing the weight of a connecting rod from analysing journals.
This chapter is going to review connecting rod failure and analyse the root causes of the
problem.
2.1 Introduction
The development of the Zx7r engine is advancing in technology every year due to
competing in main championships such as Moto GP and World Superbikes. Competing
with rival teams, the bikes have to be able to produce power to be able to win races and to
avoid engine failure. Main causes of engine failure is from the connecting rod, due to
excessive forces its put under from higher compression ratios and tighter tolerances to
produce more power.
The invention of the internal combustion four stroke engines was patented by Nikolaus
August Otto in 1867 the engine was named the Otto cycle (Heywood John B, 1988).
The diesel engine was developed by Rudolph Diesel in 1892 (Heywood John B, 1988).the
diesel engine has more torque and was more powerful than the petroleum engine and
therefore was ideal for heavy type work.
There are many types of IC engines being used today, mainly used for automotive
purposes such as motorcycles, cars, trucks and aviation. The advancement in technology is
developing engines which are smaller more powerful and fuel efficient, and due to tighter
manufacturing tolerances, stronger and lighter materials are being used and they are
becoming more reliable.
There are many different engines requiring different fuels such as Gasoline, Diesel,
Biofuels, steam and aviation. The next chapter will be explaining the background and the
different categories of engines.
16. 4
2.2 Types of Engines
There are many types of engines which are being developed further to improve fuel
efficiency, CO 2 emissions, reliability and reduce vibration. Below is a list of the different
types of engines.
Steam engine
Two Stroke engine
Four stroke engine
2.2.1 Steam Engine
A steam engine produces mechanical work by means of expanding gasses Figure 2-1
shows the diagram for a steam engine. This type of engine is similar to a combustion
engine, the difference is there are two steam inlet ports top and bottom of the cylinder,
when the piston is at full stroke steam is released via a valve which exerts a pressure on
the piston and retracts the piston. Once the piston is in the retract position, a steam inlet
valve opens and exerts a pressure to the back of the piston extending its stroke.
Combustion engines were developed from the theory of the steam engine (Heywood John
B, 1988) and were improved to run on a fuel. Steam engines are cleaner to the environment
compared to the combustion engine, but the steam engine has to be heated up, taking
considerable amount of time before the engine can be in use.
Figure 2-1: Diagram of a steam engine (Steam engine terminology and operating principles May 2011)
17. 5
2.2.2 Two Stroke Engine
IC engines can vary depending on the requirement; two stroke engines seen in Figure 2-2
don’t require the use of intake or exhaust valves, there is a reed valve which is a one way
valve which allows fuel/air mixture to enter the crankcase under high velocity, the
crankshaft rotates and circulates the fuel/air mixture into the cylinder ports where the
piston compresses the fuel and ignites from the spark plug electrode. This cycle is a two
cycle process, hence the reason they’re called a two stroke engine. These engines are
mainly used in small applications such as generators, power washers, motorcycles etc.
Main problems with the two stroke engine are they need to be rebuilt on a regular basis due
to the high rpm they reach.
Figure 2-2: Diagram of a two stroke engine process (two stroke engine exhaust November 2013)
18. 6
2.2.2.1 Cylinder ports two stroke engine
The cylinder contains ports which allow fuel/air mixture to enter and exit through different
ports. The inlet ports are situated to the rear of the cylinder where fuel/air mixture is
induced into the cylinder under vacuum, the crankshaft rotates and the piston displaces to
the top of the cylinder where the inlet ports are covered and allowing the piston to
compress and ignite the fuel. When the fuel/air mixture ignites, the piston is forced down,
rotating the crankshaft and uncovering the exhaust port and pushing the burnt gases into
the exhaust.
Some two stroke engines have a power valve which changes the height of the exhaust port
at different rpm; this allows the power from the engine to be more consistent through the
rpm.
The exhaust on a two stroke engine has to be designed so there is a certain amount of back
pressure, the shape of the exhaust is cone shaped as shown in Figure 2-3. As the piston
retracts the fuel is sucked into the cylinder and some excess fuel/air mixture is sent into the
exhaust, this is where the back pressure or echo of the sound waves which push the fuel/air
mixture back into the cylinder for the compression stroke.
Figure 2-3: Expansion chamber of a two stroke engine (two stroke engine exhaust November 2013)
19. 7
2.2.2.2 Lubrication of the two stroke engine
The fuel can either be mixed or can be fed into the engine via a pump, the oil to fuel ratio
depends on the size of the engine e.g. piston size and stroke, as the oil reduces friction, and
lubricates between the piston and cylinder wall, and also lubricates the main crankshaft
bearings and small end bearings.
2.2.3 Four Stroke Engine
The four stroke engine has a four stroke cycle; the crankshaft rotates 720 degrees for every
cycle, below in Figure 2-4 is the diagram of a four stroke engine for the four cycles. On the
intake stroke the piston moves down and the inlet valve opens and draws the fuel/air
mixture into the cylinder. The piston moves up and compresses the fuel/air mixture and is
ignited from the spark plug electrode, the explosion from the compressed fuel/air mixture
pushes the piston down, from the kinetic energy developed the crankshaft rotates, the
exhaust valves open and the piston pushes the exhaust gasses out of the cylinder.
These types of engines are very reliable and are able to cover high mileage. With
advancement in technology the engines are getting more compact and more economical.
The four stroke engine is more complicated compared to a two stroke engine as four stroke
engines require camshafts, timing chain, and inlet and exhaust valves. These types of
engines cannot reach high rpm compared to the two stroke engine because of the dynamic
forces from the timing chain, inlet, exhaust valves and the valve springs.
Figure 2-4: Diagram of a four stroke engine (Twelve Budget Output Four Stroke Diagram, 2013)
20. 8
2.2.4 Diesel Engine
The diesel engine was named after Rudolph Diesel, which he invented in 1892 (Heywood
John B, 1988). The diesel engine is widely used around the world, mainly for automotive
use; their main uses are for cars, trucks generators and ships. The diesel engine has many
advantages compared to the petroleum engine, there more economical and can produce
more torque due to higher compression ratios.
The diesel engine is a four stroke engine, the properties of diesel require a higher
compression force to be ignited, as diesel is not as flammable as petrol, glow plugs are
used instead of spark plugs in a diesel engine as it’s the compression cycle that ignites the
fuel once the engine is started.
21. 9
3.1 The Connecting Rod
This chapter is going to review the different methods used to evaluate the stresses of a
connecting rod and improve the design using different materials and looking at the
structure of the connecting rod to evaluate the best type of structure.
3.1.1 Introduction
The connecting rod shown in Figure 3-1, and the piston are the main parts of an engine
which are under extreme conditions from the dynamic forces of acceleration and
deceleration, therefore the connecting rod is a major factor in the reliability of an engine
(Moon Ky Lee a et al, 2010).
Different manufacturing methods are used in producing a connecting rod, depending on the
application and forces it is put under, this will be reviewed in chapter 3.2.
The connecting rod has to be able to withstand fatigue due to the forces produced to the
rod from tension, compression, bending and inertia forces of the rod.
Failure can be caused by lubrication failure, when the two metals from the connecting rod
and crankshaft pin meet and cause excess metal to overlap causing redistribution of the oil.
This can be the root cause of engine failure. Also other types of failure are due to buckling
which will be reviewed in chapter 3.1.5.
Figure 3-1: Diagram of a connecting rod (Luke Schreier, 1999)
22. 10
3.1.2 Materials
Selection of materials plays an important role, there are many factors needed to be
considered for the connecting rod to be strong enough to withstand forces such as inertial
forces and rigid enough to withstand the forces from buckling or exceeding its yield/
compressive strength. The connecting rod used is from a 750 cc motorcycle engine and the
material used is 708M20 steel which is the main material used for connecting rods in
motorcycle engines.
There are many types of engines used worldwide and there are materials used for
connecting rods which apply to different situations depending on the application needed
Table 3-1 displays lists of materials which are used in general engines (Michael f 1988).
Table 3-1: list of materials used for general automotive use (Michael f 1988)
Nodular cast iron,
Hsla steel 4140 (o.Q T-315)
AL 539.0 casting alloy,
Duralcan AL-SiC (p)
Composite, Ti-6-4,
Most connecting rods are made from iron in the automotive industry as this is the cheapest
method for producing connecting rods. These are mainly used for cars and trucks, to keep
the cost of materials and manufacturing to a minimum.
For high performance engines the connecting rod is required to be light yet strong, Table
3-2 is an example of materials used for this purpose. For high performance engines, cost
may not be an issue so the selection of the strongest material is more important, such as for
competition use. In some cases the material may need to be strong and light but yet the
costs may need to be monitored.
Wrought processing and powder metallurgy are the main processes for competitive mass
production, near net shape from powder metallurgy results in less machining of the rod and
tighter tolerances can be achieved and results in no waste (Michael F, 1988).
23. 11
Table 3-2: materials used for high performance connecting rods (Michael f 1988)
Magnesium alloys
Titanium alloys
Beryllium alloys
Aluminium alloys
Connecting rods made from titanium or titanium alloys are mainly used in the high
performance industry due to the material properties. Titanium is used for high performance
engines due to their strength to weight ratio, which allows the engine to achieve maximum
rpm at a faster rate and reduces inertia stresses and vibration to the engine.
A new titanium PM material was formed by (Qiu J.W et al, 2012) who states that this new
material has higher strength properties compared to PF-11C50/60 steels. Due to the
properties of this titanium, it can be used for the purpose of high performance connecting
rods. (Qiu J.W et al, 2012) states that the relative density of the material has an impact to
the mechanical properties
Using a titanium material Ti–1.5Fe–2.25Mo (wt.%), which is used in powder metallurgy,
is compared to PF-11C50/60 steels shown in Table 3-3
Table 3-3: Titanium alloy compared to PF-11C50/60 steels (J.W. Qiu a et al, 2012)
24. 12
3.1.3 Structure
The structure of a connecting rod plays a major role into the strength when in motion.
There are many types of connecting rods which represent different shapes for different
applications. I-beam type connecting rods seen in Figure 3-2 can achieve higher rpm
because the mass of the rod is low and the inertia forces are reduced, but are limited to the
amount of compression from the cylinder as the connecting rod can only withstand a
certain cylinder pressure due to the structure of the rod. Figure 3-3 shows an H beam
connecting rod, these types of connecting rods are usually used in engines requiring high
compression due to the stiffness of the design but are limited to maximum rpm due to the
weight as the inertia forces are increased.
Figure 3-2 I-Beam Connecting Rod (R&R Racing Products Current Catalogue)
Figure 3-3 H-Beam Connecting (Rod R&R Racing Products Current Catalogue)
25. 13
3.1.4 Fatigue
Literature review suggests static cyclic loads in compression and tensile loading to obtain
resultant loading. Fatigue strength under cyclic load is the most critical factor compared to
the constraints of static strength and buckling resistance. Optimum load of maximum
compressive and tensile loads applied to the constraints (Shenoy et al, 2005).
The structural factors were the buckling effects, bending, stresses and the stiffness of the
connecting rod. Maximum tensile loads increase at the crank end and the compressive
forces increase at the small end pin connecting to the piston. The forces to the small end
have different forces to the big end while in rotation.
(Shenoy et al, 2005) used Quasi-dynamics to analyse crack growth of the material while in
motion, Figure 3-4 shows the connecting rod main stress areas. From their results the main
areas of high stress were at points 3, 4, 9, 10 and 11. High stress was also concentrated at
location 11 at the oil hole, this is a stress concentration area, modifications to this area
could be considered in the design. Increasing the radius to the edges of the rod to reduce
stress concentration and increasing the section modulus to reduce bending stresses. The
possibility of reducing material at the shank region of the connecting rod is also a
possibility.
Figure 3-4: Location of stresses (Pravardhan S et al, 2005)
26. 14
Figure 3-5 shows the results from FEA specifying displacement for failure index which is
the inverse of factor of safety; this is used to calculate the severity of the stress before the
analysis is undertaken (Shenoy et al, 2005). Equation 3.1 shows the calculation for FI.
Equation 3.1
Seen in Figure 3-5, the constraints were used without the use of the connecting pin from
the crankshaft, the flanges at point 1 are compressing and have the highest stress
concentration factor. According to (Shenoy et al 2005) they described that when the pin is
in place for the analysis the stress concentration area reduced considerably.
Figure 3-5: Von Mises stress displacement of rod under tensile loading using Failure Index FEA (Pravardhan
S. et al 2005)
Figure 3-6 includes the pin on FEA, springs were put in place and this increased the
rigidity of the connecting rod. As shown in Figure 3-6 the stress concentration is reduced.
The oil to lubricate the shell bearing was ignored as this didn’t affect the rigidity of the
connecting rod.
1
.
27. 15
Figure 3-6: Von Mises stress displacement of rod under tensile loading using Failure Index FEA, FE model
with springs to the right (Shenoy. et al 2005)
(Mirehei et al, 2008) studied the fatigue life of a universal tractor using Ansys to find the
life span of a connecting rod, he also stated that stress concentration factors can be used to
calculate the life span of the rod. (Shenoy, 2004) states that the mesh type to be used
within Ansys is the tetrahedral mesh as he states this is a high quality mesh and produces
more accurate results compared to the TET4 mesh. According to (Rahman et al, 2007,
2008b) he states that the TET 4 mesh is too stiff and is not as accurate.
(Mirehei et al, 2008) studied the fatigue life of a universal tractor and worked out the life
span of the connecting rod and he also states that the stress concentration factor can be
used to calculate the life span. (Shenoy, 2004) states that the minimum value for the factor
of safety should be three for a high fatigue life.
28. 16
3.1.5 Buckling
Buckling of the connecting rod is to be considered when reducing the size of the shank
compared to the yield strength and fatigue (Lee a et al, 2010). They also state that the
buckling sensitivity is higher than that of yield strength and fatigue. There are different
types of buckling, side buckling where the connecting rod bends on the same direction as
the connecting pin shown in Figure 3-7b. Front and rear buckling is the bending of the rod
from the front and rear of the rod, due to excessive force produced on the rod shown in
Figure 3-7a. (Lee a et al, 2010) refers to the Euler formula to determine the critical
buckling of the connecting rod. This only applies to long slender beams and certain
boundary conditions, because of the geometry of the connecting rod this formula cannot be
used. Buckling is stated to be an important factor to the redesign of the connecting rod
when reducing the size. To determine the maximum buckling load the Gordon Rankine
formula equation can be used to determine the maximum force that can be applied to the
connecting rod.
Figure 3-7: Effects of buckling to a connecting rod (Moon Kyu Lee a, Hyungyil Lee a,*, Tae Soo Lee a,
Hoon Jang, 2010)
29. 17
3.2 Manufacturing
The manufacturing of connecting rods has a major impact to the strength, fatigue, cost and
the production rate. There are several ways to manufacture connecting rods, but some of
the processes are restricted in the mass production as being too slow or too expensive.
Different methods of manufacturing connecting rods can be seen below;
Sandcasting
Wrought Forged
Powder Metallurgy
Fracture Splitting.
These processes will be further explained and evaluated to find a process which produces a
strong connecting rod and has a high number of fatigue cycles and also considering the
cost of the process.
3.2.1 Sandcasting
Sand casting is a process where moulds are made from sand, an object resembling the
shape of the mould is placed in a box and sand is then added and compacted to form the
shape of the connecting rod. Molten steel is then poured into the mould and left to cool.
The connecting rod is then heat treated and straightened to tolerance accuracy. This
process produces 90% of the connecting rod; other machining processes have to be done to
produce the radii and surface finish. (Visser Danielle, 2008) states this process is
economically competitive compared to forging due to the extended tool life.
The advantages of sandcasting are
Processes 90% of the connecting rod
Reduced machining
Waste of material reduced
Disadvantages
Poor surface finish
Requires machine operations
Not suitable for mass production
Slow process
30. 18
3.2.2 Wrought Forged
Wrought forging process involves a number of dies where plain carbon steel is heated and
placed on top of the die where several blows are applied to form the shape, the metal billet
is then placed on several more moulds until the desired shape is produced. Excess metal is
removed before being heat treated and straightened. The final finishing processes involve
milling, broaching, boring, honing and grinding to obtain the required dimensions. From
this process between twenty five and thirty percent of excess metal is removed from the
rough stock.
The advantages of wrought forging are
Produces directional grain
Voids are removed from the internal structure increasing strength
Increases density, strength and hardness
Disadvantages
Involves several processes
Time consuming
Waste material
Machining necessary to correct tolerances
31. 19
3.2.3 Powder metallurgy
Powder metallurgy involves mixing different metallic powders which are then placed in a
die where a press compresses the powder into a near net shape of the connecting rod, it is
then put through several heat cycles to sinter and bond the powder.
The advantages of this process are
Near net shape finish
Accurate tolerances
No waste
Disadvantages
Density of structure reduced compared to forging
Expensive tooling for small production
Production of powder metallurgy very high
3.2.4 Fracture splitting
This method is a fairly new technology which enables the connecting rod to be forged as a
complete unit, the rod is then hardened and a force is applied to fracture the connecting rod
at the cap end. This enables the connecting rod and cap to align perfectly. This reduces the
machining processes such as sawing and increases productivity. A C-70 steel was
developed which could be fracture split, this was developed in Europe in the early 2000s
(Visser Danielle, 2008). This method can be done at room temperature and cuts the energy
costs for production.
32. 20
4. Materials & Methods
This chapter will be discussing the methods undertaken and evaluate any problems which
arised during the analysis. The connecting rod is known for engine failure, this chapter will
be investigating different methods to find the cause. This chapter will also be investigating
different means of reducing stress concentration by using different size fillets and using
different materials.
The connecting rod was analysed to find out the root cause of failure, there are many types
of failure such as fatigue, material defects and buckling. This chapter will investigate each
of these cases to find the cause of
failure and also to reduce weight.
Figure 4-1 displays the engine
assembly before it was disassembled.
The internal parts of the engine were
disassembled, measured and
modelled and were analysed using
finite element analysis.
The method for the redesign process
can be seen in Figure 4-2 this method
will be used until optimisation of the
connecting rod is achieved.
Figure 4-1 Engine Assembly
34. 22
4.1 Design process
The objective function is to reduce weight of the connecting rod by means of reducing the
area of the shank and also where least stress occurs, sections can be reduced in size but
careful consideration has to be made to the reliability, fatigue life and also if the
connecting rod can withstand the forces. Reduction of cost is also a factor to consider, such
as the manufacturing cost. The shape has a major factor from manufacturing and any
changes in the shape will be considered.
Choice of materials is a constraint to the strength of the connecting rod and this will limit
the material properties of the connecting rod. There are many materials which have good
strength to weight ratio but this comes at a cost.
There are many design variables to be considered in the connecting rod, evaluation of the
stresses within Ansys will determine areas which can be reduced.
The redesign process will involve modelling the connecting rod, importing the model to
Ansys and analyse the main stress concentration areas and reduce any areas which are
significantly below the yield stress. This process will be repeated until a limit is reached
until such that the number of cycles of fatigue increases.
35. 23
The engine was disassembled and the internal parts, piston, connecting rod assembly and
crankshaft were measured and modelled within Creo which can be seen in appendix A.
The 3-D model was then animated for the purpose of the presentation to explain how the
engine works. Figure 4-3 displays the rendered engine assembly.
Several problems were encountered from the model of the connecting rod when importing
into Ansys as an IGES file. The model is supposed to be a volume within Ansys, but due to
the complexity of the model this didn’t happen. Due to this problem the model of the
connecting rod was simplified until it could be imported as a solid. The reason for this
happening is the procedure of modelling within Creo has to be done in a precise way to
avoid complications within Ansys.
Figure 4-3: Rendered model of the crankshaft, connecting rods and pistons
36. 24
Figure 4-4 Connecting rod assembly and model of connecting rod from Creo Parametric
Figure 4-4 shows the assembly of the connecting rod and cap and the modelled connecting
rod. The volume of the connecting rod can be seen in Figure 10-6, Appendix A.
Table 4-1 shows the technical information of the motorcycle engine and information is
given for the material properties of the connecting rod and piston. The mass of the
connecting rod was compared to the model and was calculated using equation 4-1.
Equation 4-1
Where ρ = 7.85 * 103
kg/m3
V = 35.47*10-6
m3
Mass = 0.278 kg
37. 25
The mass of the actual connecting rod is 0.205 kg. There is a twenty six percent difference
between the model and the actual connecting rod. The difference in the masses could be
due to several reasons; the connecting rod was measured using Vernier calliper and a micro
meter, a more accurate way of measuring is to use a coordinate measurement machine.
Table 4-1: Technical information of the engine (Kawasaki ZX 7R 96-03 Service Manual)
Engine Type 4-Stroke, DOHC, 4 cylinder
Bore and Stroke 73.0×44.7mm
Displacement 748 cm3
Compression Ratio 11.5
Maximum Power 90 kW @ 11800 rpm
Maximum Torque 78 NM @ 9300 rpm
Piston Diameter 72.952mm
Cylinder Diameter 73mm
Table 4-2 Material properties of the original connecting rod
Material 708M20
Young’s Modulus 206 GPa
Poisson Ratio 0.27
Tensile Strength 880 MPa
Density 7.85 kg/m3
Yield Strength 680 MPa
Elongation 16 %
Fatigue Limit 800 MPa
Mass of Gudgeon Pin 0.035 kg
Mass of piston 0.125 kg
Mass of Connecting Rod 0.14 kg
Mass of Cap 0.065 kg
Table 4-2 displays the material properties of the connecting rod and piston assembly.
These properties will be used within Ansys for the material properties and the results can
be compared to the yield strength and compressive stress to that in the table to see if failure
will occur.
38. 26
4.2 Force Calculations
Figure 4-5 represents a free body diagram of the crankshaft, connecting rod and piston.
From this diagram it can be broken up into different segments to analyse the forces given
the torque from Table 4-1.
Figure 4-5: Diagram of crankshaft, connecting rod and piston
R=Crankshaft radius
L=length of the connecting rod
W=mass of the piston
R= displacement
= angle of rotation
= angle phi
R = 0.0225m
L = 0.1m
R = √(0.0025)2
+ (0.1)2
R = 0.1025m
= Tan-1
0.0225/0.1025
= 12.38°
= 90 – 12.38
= 77.62 °
r
R L W
r
39. 27
The torque given from the manufacturer of 78Nm from Table 4-1 is produced from the
crankshaft, given this free body diagrams can be used to find the force applied to the
piston. Assuming no losses within the engine due to friction, this will be discussed in
chapter 4.3.
Figure 4-6: Free body diagram of crankshaft (R)
40. 28
To find the reaction forces using sum of the forces and moments.
∑ Fx = 0 = -49 + R2cos(77.62) = 0
R2 = 228.55 N
∑ M = 0 = 78 + R2sin(77.62)(0.0225) = 0
R2 = 3550.29N
R2 = 78Nm/0.0225sin77.62
R2 = 3550.29 N
∑ Fy = 0 = -R1 + 3550.29 = 0
R1= -3550.29N
Figure 4-7: Free body diagram of connecting rod
C1 = R2
C2 = -3467.73 N
The total force acting on the connecting rod in compression is 3467.73 N which is due to
the ignition forces from the piston. Dividing this force over the projected area of the
gudgeon pin will give the pressure applied to the connecting rod.
Pressure= F/A
Projected area = 15.588*18
A = 280.59 mm2
P = 12.35 MPa
41. 29
4.3 Inertia Forces
Figure 4-8: Velocity and acceleration graphs (NORTON, R.L., 2003)
Figure 4-8 represents the velocity and acceleration forces produced from the dynamic
forces of the connecting rod and the piston, graph developed from Engine software. Using
equation 4-2 which was setup from the free body diagram in Figure 4-5, the displacement
can be calculated. Software used from Design of Machines which uses a software package
called Engine which calculates the inertia forces given in equations 4-2, 4-3, and 4-4.
√ ( ) Equation 4-2
Equation 4-3 is the second derivation of equation 4-2 which is the velocity, from this
equation it can be derived to find the acceleration shown in equation 4-4.
√ ( )
Equation 4-3
42. 30
( )(( ) ( ) )
Equation 4-4
As force is equal to mass times acceleration the forces exerted from the piston to the
connecting rod in tensile force can be calculated using equation 4-5. Using all these
equations the results can be graphed shown in Figure 4-8.
Equation 4-5
Mass piston and gudgeon pin = 0.16 kg
a = 13103.8 m/s2
F = 2096.61 N
To find the pressure acting on the connecting rod due to the acceleration force we use
equation 4-6.
Equation 4-6
F = 2096.61N
Projected area = 15.58*18 = 70.15
A = 280.59 mm2
P = 7.47 MPa
43. 31
4.4 Reduction of Shank
The Gordon Rankine formula can be used to find the maximum load produced on the
connecting rod before buckling occurs, using equation 4-7. The details of the cross section
and moment of inertia can be seen in appendix B Figure 11-1.
Equation 4-7
Where,
σc= Compressive Strength
A = Area
α = 1/7500 (For a pinned-pinned support)
L = Length of the shank
K = Axis of Gyration
√
( )
Equation 4-8
Pr = 43755.19 N
The maximum buckling load the shank will be able to withstand from buckling is 43755.19
N from equation 4-8. To find the factor of safety by dividing Cr over the max load applied
from the compressive force equation 4-9 gives.
Equation 4-9
n = 12.62
The next step is to reduce the cross sectional area using equation 4-7. Inputting the
equation into Excel and reducing the factor of safety to three, the minimum area can be
calculated, the graph shown in Appendix B Figure 11-6 was used to show area vs critical
load in. This method was used to calculate the minimum area needed.
√
( )
Pr = 11276.33 N
Equation 4-10
n = 3.25
Using equation 4-10 and dividing Cr by the max compressive load the factor of safety is
reduced to 3.25. The new cross sectional area and the moment of inertia can be seen in
Appendix B Figure 11-4.
44. 32
4.5 Friction
Friction was considered to see how much of an effect this had between the lubrication
point of the crank pin and the connecting rod. To determine the shear viscous stress of the
fluid, assuming there is a linear velocity within the distribution of the fluid. Figure 4-9
represents the dimensions of the conrod. Using equation 4-11 to find the velocity with
respect to the oil clearance.
Equation 4-11
Oil clearance = mm
Equation 4-12
= Angle of rotation of the connecting rod
Rpm = 5900
Velocity = 44.33 m/s
Equation 4-13
ϓ = 1.847×106
1/s
To determine the shear forces using 4-14
Equation 4-14
F = 22.09 N
45. 33
To find the moment caused from the shear viscous force from the oil, calculating the
moment produced using equation 4-15.
Moment = Force × Distance Equation 4-15
Moment = 22.09×0.017
Moment = 0.375 Nm
Because the friction from the shear viscous forces of the oil is so small, friction will be
neglected in this study.
Figure 4-9: Dimensions of the crank pin
46. 34
4.6 Fatigue
A fatigue analysis will show how the connecting rod will last with stress amplitudes
applied over time. To find the factor of safety and the infinite number of cycles for the
original connecting rod at the weakest section shown in Figure 4-10, section A-A. Using
material properties of 708M20 steel from Table 4-3.
Table 4-3: Material properties of each material
Material Density
kg/m3
Youngs Modulus
(GPa)
Yield Strength
(MPa)
Tensile Strength
(MPa)
Cost
(euro/kg)
Titanium Alloy 4600 115 975 1100 20.9
Medium
Carbon Steel
7850 208 602.5 805 0.47
Low Alloy
Steel
7850 211 950 1155 0.50
708M20 Steel 7850 206 680 880 0.72
High Carbon
Steel
7850 207.5 780 1095 0.47
Figure 4-10: Section A-A Fatigue
The endurance strength takes into account all the factors which will reduce the life of the
material such as the material properties, surface finish, fillets and the section size
difference from one section to the other.
Se = Endurance strength
Se = ka,kb,kc,kd,ke se’
Se’= [0.566-9.68*10-5
*880]880 = 414.31 MPa
47. 35
Ka = Surface finish (Appendix D, Figure 13-3)
Kb = Size factor
Kc = Reliability (Appendix D, Figure 13-4)
Kd = Temperature
Ke = Stress concentration (Appendix D, Figure 13-2)
Ka = 0.35 (Forged)
Kb = 1 (Axial loading)
Kc = 0.814 (Reliability of 99%)
Kd = 1 (Temp <350 degrees)
Ke = 1/Kf
Kf = 1+q(Kt-1)
q = 1 (Appendix D, Figure 13-1)
Kt = d/w = 18/24.5 = 0.7346
h/w = 12.25/24.5 = 0.5
Kt = 0.22
Kf = 1+0.9(0.22-1)
Kf = 0.298
Se = (0.35)(1)(0.814)(1)(0.298)(414.31)
Se = 35.17 MPa
σm = Mean stress
σa = Stress amplitude
Equation 4-16
Equation 4-17
Using equation 4-16 and 4-17 to find the mean and amplitude stress.
σm = 9.91 MPa
σa = 2.44 MPa
To find the factor of safety for fatigue using equation 4-18.
48. 36
Sut = 880 MPa
Se = 35.17 MPa
Equation 4-18
n = 12.40
To find the infinite number of cycles using equation 4-19
-
Equation 4-19
( )
Sut = 880 MPa
Se = 35.17 MPa
N = 1.67×106
cycles
The calculations for the number of cycles for fatigue for each material can be seen in
appendix C.
49. 37
4.8 Finite Element Analysis
A finite element analysis was carried out to analyse the stresses on the connecting rod.
Given the forces calculated from chapter 4.2, these were applied to the connecting rod
surfaces as a pressure. Because the pressure over the area of the pin is not evenly
distributed, the pressure was reduced over hundred and twenty degrees, seen in Figure
4-11. The connecting rod was modelled using Creo and imported into Ansys 14.5 as an
IGES file. The academic version of Ansys software used is limited to thirty two thousand
nodes, to reduce the number of nodes symmetry was used. Due to the model being
symmetric, the model was split into a quarter of its original size which reduces the number
of nodes and decreases the amount of time to solve. Material properties were then specified
and inputted. The element type was then selected, the element type is Tet 10 which is used
for a 3-D structural analysis. Figure 4-12 displays the pressure applied at area 2 of 12.35
MPa.
Figure 4-11: Pressure distribution over the surface of a pin (Webster et al, 1983).
50. 38
Figure 4-12: Pressure applied to area 2
The boundary conditions were applied to area 3 in all degrees of freedom shown in Figure
4-13. Areas 36, 117 and 95 were constrained in the x-direction. Areas 8, 32, 2,102 and 10
were constrained in the z-direction. A pressure of 7.47 MPa was applied to area 2 for the
tensile analysis.
Figure 4-13: Boundary conditions
51. 39
Figure 4-14 displays the mesh on the connecting rod. The mesh was refined at the highest
stress points at the upper and lower point of the shank. Refining the mesh at these points
gives a more accurate answer.
Figure 4-14: Mesh refinement
52. 40
4.9 Material Selection
CES Materials was used to find the best material regarding cost, strength and density.
Applying constraints in CES Materials to reduce the selection of materials listed below. An
important factor to be considered in the selection of material is it has to withstand high
compressive buckling forces and tensile forces.
Fatigue is an important factor as the material has to withstand a high number of cycles.
Below is the objectives and constraints to decide what factors will be used to find the
appropriate material within CES Materials.
Objective
To select an appropriate material
Constraints
To be as light as possible
Cheap as possible
Strong enough to carry peak load without failure from fatigue
Table 4-4: Constraints applied CES Materials
Physical attribute Minimum Maximum
Fracture toughness 15 MPa √
Service temperature 200 degrees
Using equation 4-20 to find the strength to weight ratio and also inputting the price on the
x-axis, this will determine the cost of material with respect to the strength to weight ratio
seen in Figure 4-15.
Equation 4-20
P = density
E = Youngs Modulus
53. 41
Figure 4-15: Youngs Modulus /Density Vs price
Medium carbon, high carbon and low alloy steel have the highest strength to weight ratio
and are also the lowest cost. Titanium has a much higher cost compared to the materials
previously mentioned.
Figure 4-16: Compressive strength Vs fatigue strength
Figure 4-16 displays the compressive strength vs fatigue strength. The compressive
strength of the low alloy steel has a wide range of strength but also has a high fatigue life.
Titanium alloys also has a high fatigue life and the range of compressive strength is
reduced compared to the low alloy steel.
54. 42
Figure 4-17: Tensile strength Vs fatigue strength
Figure 4-17 displays the tensile forces vs fatigue strength. Again the low alloy steel looks
to be the best material for fatigue life and tensile strength.
From analysing all the graphs from CES Materials low alloy steel has the best material
properties and is cost effective.
55. 43
4.10 Manufacturing
Manufacturing has a big impact on the material properties such as the density, where
forging produces a connecting rod of high density due to the blows applied during
manufacturing. Using CES Materials to find the best methods to manufacture the
connecting rod, limits were applied which can be seen below in Table 4-5.
Table 4-5: Limits applied in CES Materials
Figure 4-18 displays the economic batch size compared to the relative equipment cost.
Forging has a high equipment cost compared to powder and sintering which has a medium
equipment cost, powder and sintering can produce higher batch sizes compared to forging.
Figure 4-18: Economic batch size vs relative equipment cost
Physical attribute Minimum Maximum
Mass Range 0.4 kg 0.6 kg
Section thickness 2.5mm 30mm
Tolerance <0.25 mm
Bore tolerance <0.02 mm
Surface Finish <5 µm
Batch size 10000 units
56. 44
Figure 4-19: Roughness vs relative cost index
Figure 4-19 displays surface roughness vs relative cost index per unit. Pressing and
sintering produces the best surface finish compared to the other processes. Sand casting
and forging would require further machining processes to achieve a good surface finish.
Figure 4-20: Tooling cost
Figure 4-20 displays the tooling cost for each process, sand casting produces the lowest
cost and forging and press sintering are around the same.
57. 45
5. Results
This section will review the results and specify the optimum connecting rod. The model of
the connecting rod was converted to an IGES file and exported into Ansys. Problems were
encountered with the complicated geometry of the model, the connecting rod model was
simplified to allow for analysis within Ansys.
Figure 5-1 shows the points at which failure would likely occur and this will be used to
show the stress at these locations. From Ansys the stress at points A-A, B-B, C-C and D-D
will be shown for each analysis.
Figure 5-1: Stress locations
58. 46
5.1 Stress Results Tension
5mm Fillet
Table 5-1 displays the stress at each location given in Figure 5-1 for a 5mm fillet. The
highest stress concentration occurs at section B-B. The Von Mises stress can be seen in
Figure 5-2 where the max stress can be seen at the fillet at the top of the shank. The factor
of safety was also done to find the weakest point of the connecting rod.
Table 5-1: Location of stress, FOS and displacement (5 mm fillet)
Figure 5-2: Von Mises stress 5mm fillet (Tension)
Section Stress (MPa) Factor of Safety Max displacement
mm
A-A 106.80 6.37
B-B 172.69 3.94 0.039771 mm
C-C 94.11 7.23
D-D 44.89 15.15
59. 47
7mm Fillet
Figure 5-3 shows the Von Mises stress with a 7mm fillet. Table 5-2 displays the stress at
the four locations of the connecting rod.
Table 5-2: Location of stress, FOS and displacement (7 mm fillet)
Section Stress (MPa) Factor of Safety Displacement mm
A-A 124.67 5.45
B-B 160.3 4.24 0.028761mm
C-C 146.73 4.63
D-D 146.73 4.63
Figure 5-3: Von Mises stress 7mm fillet (Tension)
60. 48
10mm Fillet
Figure 5-4 displays the maximum Von Mises stress using a 10mm fillet. Table 5-3 displays
the stress at the four locations.
Table 5-3: Location of stress, FOS and displacement (10 mm fillet)
Figure 5-4: Von Mises stress 10mm fillet (Tension)
Section Stress (MPa) Factor of Safety Displacement mm
A-A 107.36 6.34
B-B 142.47 4.77 0.031588mm
C-C 85.831 7.92
D-D 44.89 15.15
61. 49
15mm Fillet
Figure 5-5 displays the Von Mises stress using a 15mm fillet. Table 5-4 displays the stress
at the four locations.
Table 5-4: Location of stress, FOS and displacement (15mm fillet)
Figure 5-5: Von Mises stress 15mm fillet (Tension)
Section Stress (MPa) Factor of Safety Displacement mm
A-A 107.82 6.31
B-B 173.20 3.93 0.039737mm
C-C 95.41 7.13
D-D 44.95 15.13
62. 50
5.2 Stress Results Compression
The results for the load applied in compression using 5, 7, 10 and 15 mm fillets are shown
in this chapter.
Figure 5-6: Stress location points
Table 5-5 displays the stress at the four sections of the connecting rod, (Figure 5-6)
displays the results at each point.
Table 5-5: Location of stress, FOS and displacement (5mm fillet)
Figure 5-7 displays the Von Mises stress, the highest stress concentration is located at the
top of the shank.
Figure 5-7: Von Mises stress 5mm fillet (Compression)
Section Stress (MPa) Factor of Safety Displacement mm
A-A -23.89 28.46
B-B -196.84 3.45 0.031829 mm
C-C -120.11 5.66
D-D 0.37113 -
63. 51
7mm Fillet
Table 5-6 displays the Von Mises stress at each location of the connecting rod.
Table 5-6: Location of stress, FOS and displacement (7 mm fillet)
Section Stress (MPa) Factor of Safety Displacement mm
A-A -23.250 29.24
B-B -146.8 4.63 0.033712 mm
C-C -116.14 5.85
D-D 0.2246 3090
Figure 5-8 shows the Von Mises stress, where maximum stress occurs at the lower shank.
Figure 5-8: Von Mises stress 7 mm fillet compression
64. 52
10mm Fillet
Table 5-7 displays the stress using a 10 mm fillet, Figure 5-9 displays the Von Mises stress
where max stress occurs at the top of the shank.
Table 5-7: Location of stress, FOS and displacement (10 mm fillet)
Figure 5-9: Von Mises stress 10 mm fillet compression
Section Stress (MPa) Factor of Safety Displacement mm
A-A 12.65 53.71
B-B -106.87 6.36 0.031588 mm
C-C -120.73 5.63
D-D 0.363 -
65. 53
15mm Fillet
Table 5-8 displays the stress using a 15 mm fillet, Figure 5-10 displays the Von Mises
stress where max stress occurs at the top of the shank.
Table 5-8: Location of stress, FOS and displacement (15 mm fillet)
Figure 5-10: Von Mises stress 15 mm fillet compression
Section Stress (MPa) Factor of Safety Displacement mm
A-A -36.88 18.44
B-B -90.08 7.55 0.031759 mm
C-C -115.32 5.89
D-D 0.38 -
66. 54
Graphing the results using various size fillets from compression and tensile forces, it can
be shown which fillet is the best option for reducing stress concentration. Figure 5-11
shows the stress at different locations of the connecting rod. The ten millimetre fillet
reduces the stress concentration in tensile forces, but the 15mm fillet reduces the stress in
compressive forces. The stress from the 10mm fillet isn’t much higher than the 15mm fillet
in compression, the 10mm fillet would probably be the best option for the design due to a
big reduction in the tensile stress. Section A-A would be the weakest section of the
connecting rod resulting in the 10mm fillet being the most optimum fillet.
Figure 5-11: Results of 5, 7, 10 and 15 mm fillets, compression and tension
-250
-200
-150
-100
-50
0
50
100
150
200
A-A B-B C-C D-D
StressMPa
Section
Stress Comparison of 5, 7, 10, 15mm Fillet
Tensile 10mm Red CSA
Compression 10mm Red
CSA
Compression 5mm Red
CSA
Tension 5mm Red CSA
Compression 15mm Red
CSA
Tension 15mm Red CSA
67. 55
Figure 5-12 shows the displacement with a compressive force applied using different size
fillets, the 7mm fillet seems to be considerably higher compared to the rest of them, there
may have been a wrong input within Ansys as this result doesn’t match closely with the
rest of the results.
Figure 5-12: Displacement with compressive load
Figure 5-13 shows the difference in displacement between the fillets with an axial force in
tension, the lowest displacement is the 7mm fillet.
Figure 5-13: Displacement with load in tension
0.031829
0.033712
0.031588
0.031759
0.0305
0.031
0.0315
0.032
0.0325
0.033
0.0335
0.034
Displacementmm
Size of fillet
Displacement Compression
5mm fillet
7mm fillet
10mm fillet
15mm fillet
0.039771
0.028761
0.031588
0.039737
0
0.005
0.01
0.015
0.02
0.025
0.03
0.035
0.04
0.045
Displacementmm
Size of fillet
Displacement Tension
5mm fillet
7mm fillet
10mm fillet
15mm fillet
68. 56
5.3 Factor of Safety
Figure 5-14 shows the factor of safety with the connecting rod in tension, the 10mm fillet
produces the highest at section A-A, but comparing to the rest of the fillets it is much
higher, an error could of have occurred in the analysis. The 5 and 7mm fillet produce very
similar results and the 15mm fillet has a steady factor of safety at all the sections.
Figure 5-14: Factor of safety compression
Figure 5-15 shows the factor of safety with the connecting rod in tension, the 10mm fillet
produces the highest factor of safety over the complete section of the conrod and increases
at section D-D due to the larger section.
0
10
20
30
40
50
60
A-A B-B C-C
FactorofSafety
Location Point
FOS 5, 7, 10 and 15mm Fillet Compression
5mm fillet
7mm fillet
10mm fillet
15mm fillet
69. 57
Figure 5-15: Factor of safety Tension
Table 5-9 represents the static factor of safety for the 7 and 10mm fillet, the 7mm fillet was
the original connecting rod and increasing the fillet to 10mm at section B-B this has
reduced the stress considerably and increased the factor of safety by a factor of two.
Table 5-9: Static Factor of safety 7 and 10mm Fillet
The results show that the 10mm fillet increases the factor of safety and would be the most
suitable fillet to use from this analysis.
0
5
10
15
20
25
30
A-A B-B C-C D-D
FactorofSafety
Location Point
FOS 5,7,10 and 15mm Fillet Tension
5 mm fillet
7mm fillet
10mm fillet
15mm fillet
Fillet Size Factor of Safety
7mm (Original Conrod Compression) 4.63
7mm (Tension) 4.24
10mm (Compression) 6.36
10mm (Tension) 10.27
70. 58
5.4 Comparison of Materials
Figure 5-16 represents the different materials used for the analysis of the connecting rod.
All the tests were taken from Ansys and graphed. Comparing the different materials shown
in Figure 5-16 shows that the most suitable material is low alloy steel which coincides with
the results from the material selection in chapter 4-9. High carbon steel closely matches
low alloy steel with a compressive force applied but the low alloy steel produces much less
stress in tension.
The plots from Ansys for the various materials can be seen in Appendix D chapter 13.3.
Figure 5-16: Comparison of materials
-250
-200
-150
-100
-50
0
50
100
150
200
A-A B-B C-C D-D
StressMPa
Section
Comparsion of Materials
Low alloy steel Stress
(Tensile)
Low alloy steel Stress
(Compression)
High carbon Stress
(Tensile)
High carbon Stress
(compression)
Medium carbon Stress
(compression)
Medium carbon stress
(Tensile)
Titanium Stress
(Compression)
Titanium Stress (Tensile)
708M20 Stress
(Compression)
708M20 Stress (Tensile)
71. 59
5.6 Fatigue
Fatigue is the most important factor when considering the life of a connecting rod. Table
5-10 displays the number of cycles for an infinite life. Medium carbon steel produces the
highest number of cycles which is a small increase compared to the fatigue life of 708M20
steel. Titanium has a good fatigue life but the cost of the material is much higher compared
to the other materials. The cost of low alloy steel is higher than carbon steel but the results
from low alloy steel produce a connecting rod with a higher factor of safety and a good
fatigue life.
Table 5-10: Fatigue cycles and cost vs material
Material No. Cycles Cost (Euro/Kg)
708M20 Steel 1.67×10
6
Cycles 0.72
High Carbon Steel 1.67×10
6
Cycles 0.47
Titanium 1.67×10
6
Cycles 20.9
Medium Carbon Steel 1.68×10
6
Cycles 0.47
Low Alloy Steel 1.66×10
6
Cycles 0.5015
Figure 5-17: Original conrod and optimised conrod
Shown in Figure 5-17 displays
the original and the optimised
conrod. The shank on the
optimised conrod is considerably
smaller compared to the original
and the weight has been reduced
by 9.38 percent. The volume and
percentage difference can be seen
in Appendix A, Figure 10-6.
72. 60
6. Discussion
The factor of safety for buckling was reduced to three and the results show that the
connecting rod was still able to withstand the compressive forces applied which (Lee a et
al, 2010) recommended in the literature.
From literature (Shenoy et al, 2005) states that the maximum tensile force increased at the
crank end and the compressive force increased at the small end pin, connecting to the
piston while in motion. The results from this analysis show that the maximum stress occurs
at the small end pin in compression and tension, this analysis was only considering static.
The results from Figure 5-1 show that the optimum fillet is 10mm at the top part of the
shank. The 15mm fillet was better at section B-B but overall the 10mm fillet reduced the
stress the most at the critical parts.
Figure 5-12 displays the displacement with a compressive load, but the 7mm fillet has a
higher displacement compared to the other fillets. An error could have occurred in the
analysis and maybe another analysis would be recommenced to confirm the results.
Figure 5-13 displays the displacement with a tension force applied, the fillet with the least
displacement was the original fillet of 7mm and the 10mm was next. The 10mm has the
same displacement in tension and compression which would conclude a mistake could
have been made as different forces were applied which should result in different values.
Figure 5-14 displays the factor of safety with a compressive force applied, the 10mm fillet
has a much higher factor of safety at section A-A compared to the rest of the fillets, and
comparing the displacement mentioned earlier this would confirm that an error was made.
Figure 5-15 clearly shows that the 10mm fillet has a higher factor of safety at all the
critical points of the connecting rod with a tension force applied.
Material properties has an impact to the strength, fatigue and weight of the connecting rod,
Figure 5-16 displays the comparison of different materials used for the analysis using
Ansys. The optimum material was the low alloy steel as this produced the least amount of
stress at the critical points. The cost was also a factor, the low alloy steel was not the
cheapest but produced a connecting rod with a good fatigue life which can be seen in Table
5-10 where cost is compared to the number of cycles of fatigue.
73. 61
The manufacturing process is an important process to the finish of the connecting rod. The
strength to weight ratio was a consideration seen in Figure 4-15, the low alloy, medium
carbon and high carbon steel were closely matched for cost and strength to weight ratio.
But after considering the results the low alloy steel seems to produce the best results
overall. The surface finish vs relative cost index was graphed shown in Figure 4-19 which
shows that the powder metallurgy process produces a better quality finish compared to
forging. Applying the process of fracture splitting and powder metallurgy, this would result
in a better quality connecting rod and also reduce the cost of manufacturing compared to
forging which was recommended in literature (Visser Danielle, 2008).
74. 62
7. Conclusion
The aim of the project was to find the cause of failure of a connecting rod and to improve
the design regarding the weight, material selection and manufacturing and to reduce the
cost.
The axial forces were calculated using free body diagrams but the calculations were only
an estimate and more accurate calculations could be calculated from measuring forces from
an engine in motion. The shank was reduced and buckling was considered from the
compressive forces.
Analysing various size fillets at the top of the shank as this showed the highest stress
concentration the 10mm fillet was the optimum fillet, increasing the factor of safety and
reducing stress concentration. The best material was the low alloy steel as this had the best
material properties concerning fatigue, yield strength and cost.
The project was successful in reducing the weight of the connecting rod by 9.38 percent
and increased the factor of safety by changing the material to low alloy steel. An error may
have occurred with the analysis of the 10mm fillet so more work would need to be done to
confirm the results.
For future work to improve the analysis, a dynamic analysis could be considered which
would show the stresses at various points over the three hundred and sixty degrees of
rotation. To reduce the overall volume of the connecting rod using algorithms could be
used to find the optimum shape using software such as Matlab. Bench testing of an engine
could also be considered to compare results from FEA.
76. 64
9. References
Weight reduction method of connecting-rod by non-linear FEM analysis: Susumu Numajiri
(Mitsubishi Motors Corporation), Shinya Miura (MMC Computer Research Ltd.)',
1996. JSAE Review, 17 (1), 1//, p. 92.
ALI, S.S.P.A.F., 2013. Connecting Rod Optimization for Weight and Cost
Reduction [Online]. Available from:
http://www.eng.utoledo.edu/mime/faculty_staff/faculty/afatemi/papers/2005SAEShenoyFa
temi2005-01-0987.pdf [Viewed 7/11/2013].
BIN ZHENG, Y.L.A.R.L., 2013. 'Stress and Fatigue of Connecting Rod in Light Vehicle
Engine'. The Open Mechanical Engineering Journal, 2013, 7, 14-17.
DANIEL, G.B. & CAVALCA, K.L., 2011. 'Analysis of the dynamics of a slider–crank
mechanism with hydrodynamic lubrication in the connecting rod–slider joint
clearance'. Mechanism and Machine Theory, 46 (10),10//, pp. 1434-1452.
'Development of high strength connecting rod by forging Toyohisa Manabe, Motohide
Mori, Masaaki Yano, Takashi Kobayashi (Toyota Motor Corporation), Naoki Iwama, Ichi
Nomura (Aichi Steel Works Co. Ltd.)', 1996. JSAE review, 17 (4), 10, p. 442.
FANTINO, B. & BOU-SAÏD, B., 2003. 'Inertia, shear-thinning and thermal effects on
connecting rod bearing behaviour'. In: D. DOWSON, M.P.G.D.A.A.A.L. (ed.) Tribology
Series. Elsevier, pp. 779-787.
H. B. RAMANI, N.K., P. M. KASUNDRA, November- 2012. 'Analysis of Connecting
Rod under Different Loading Condition'. Vol. 1 (Issue 9,).
KHARE, S., SINGH, O.P., BAPANNA DORA, K. & SASUN, C., 2012. 'Spalling
investigation of connecting rod'. Engineering Failure Analysis, 19 (0), 1//, pp. 77-86.
KUBOTA TSUYOSHI, I.S., ISOBE TSUNEO, KOIKE TOSHIKATSU, 2013.
'Development of fracture splitting method for case hardened connecting rods'.
KURATOMI, H., TAKAHASHI, M., HOUKITA, T., HORI, K., MURAKAMI, Y. &
TSUYUKI, S., 1995. 'Development of a lightweight connecting rod made of a low-carbon
martensite steel'. JSAE Review, 16 (4),10//, pp. 406-407.
77. 65
Lee, Moon Kyu, Hyungyil Lee, Tae Soo Lee, and Hoon Jang, 2010 "Buckling sensitivity
of a connecting rod to the shank sectional area reduction." Materials & Design 31, no. 6.
Ahmad Ridzuan, I. (2010). Analysis of connecting rod fracture using finite element
analysis (Doctoral dissertation, Universiti Malaysia Pahang).
Mirehei, A., M. Hedayati Zadeh, A. Jafari, and M. Omid, 2008 "Fatigue analysis of
connecting rod of universal tractor through finite element method (ANSYS)."Journal of
Agricultural Technology 4, no. 2.
NORTON, R.L., 2003. Design of machinery: an introduction to the synthesis and analysis
of mechanics and machines / Robert L. Norton. 3rd/International ed.
QIU, J.W., LIU, Y., LIU, Y.B., LIU, B., WANG, B., RYBA, E. & TANG, H.P., 2012.
'Microstructures and mechanical properties of titanium alloy connecting rod made by
powder forging process'. Materials & Design, 33 (0), 1//, pp. 213-219.
RAM, B., 2013. 'Dynamic Simulation of a Connecting Rod made of Aluminium'. IOSR
Journal of Mechanical and Civil Engineering (IOSR-JMCE), e-ISSN: 2278-1684 Volume
5 (Issue 2 (Jan. - Feb. 2013), PP 01-05).
Shenoy, Pravardhan S., and Ali Fatemi., 2005"Connecting rod optimization for weight and
cost reduction." Journal of Sound and Vibration 243, no. 3.
Weight reduction method of connecting-rod by non-linear FEM analysis: Susumu Numajiri
(Mitsubishi Motors Corporation), Shinya Miura (MMC Computer Research Ltd.)', 1996.
JSAE Review, 17 (1), 1//, p. 92.
CES EduPack (2009), Granta Design Ltd., Cambridge, UK, www.grantadesign.com.
Michael f Ashby (Material Selection in Mechanical Design 1988 Second edition)
(1/11/2013)
Visser, Danielle. A Comparison of Manufacturing Technologies in the Connecting Rod
Industry. Submission to FIERF 06-06, 2008.
WHITTAKER, D., 2001a. 'The competition for automotive connecting rod markets'. Metal
Powder Report, 56 (5), 5//, pp. 32-37.
78. 66
WHITTAKER, D., 2001b. 'The competition for automotive connecting rod markets'. Metal
Powder Report, 56 (5), 5//, pp. 32-37.
R&R Racing Products Current Catalog Retrieved 2 December 2013 from
http://rrconnectingrods.com/catalog.html 2013
Steam engine terminology and operating principles May 2011. Retrieved October 10,
2013, from http://the-nerds.org/Steam-101.html
Thermodynamics Two / Four Stroke Engine 2013.Retrieved 8 October 2013, from
http://www.roymech.co.uk/Related/Thermos/Thermos_4_Stroke.html
Twelve Budget Output Four Stroke Diagram, 2013. Retrieved October 16 2013, from
Two stroke engine exhaust November 2013. Retrieved September 30 2013, from https://
two+stroke+engine&ie=utf-8&oe=utf-8&rls=org.mozilla: en-GB:official&client=firefox-
a&channel=fflb&gws_rd=cr&ei=GmF5UtylDMqf7AbWn4CgCg
WHITTAKER, D., 2001a. 'The competition for automotive connecting rod markets'. Metal
Powder Report, 56 (5), 5//, pp. 32-37.
WHITTAKER, D., 2001b. 'The competition for automotive connecting rod markets'. Metal
Powder Report, 56 (5), 5//, pp. 32-37.
Kawasaki ZX 7R 96-03 Service Manual, 2008, Retrieved 7 November 2013, from
http://www.manualedereparatie.info/download/Kawasaki-Ninja-ZX-7R-Service-
Manual.html
79. 67
10.Appendix A
Figure 10-1: Connecting rod assembly (front view and side view).
Figure 10-2: Connecting rod and cap Disassembly
82. 70
11.Appendix B
The cross sectional area for the original connecting rod is shown below. These were
calculated using MD Solids.
Figure 11-1: Original cross sectional area of shank (MD Solids)
Figure 11-2: Moment of inertia y-axis (Original connecting rod)
83. 71
Figure 11-3: Moment of inertia z-axis (Original connecting rod)
The cross sectional area for the modified connecting rod is shown below. These were
calculated using MD Solids.
Figure 11-4: Modified cross sectional area (MD Solids)
84. 72
Figure 11-5: Moment of inertia and area Y-Y axis (Modified conrod)
Figure 11-6: Area Vs Critical load
Gordon Rankine formula used to graph the area of I beam with respect to the critical load
using Excel.
0
5000
10000
15000
20000
25000
30000
35000
10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90
CriticalloadN
Area mm^2
Buckling load
Buckling load
85. 73
12.Appendix C
Fatigue Endurance Strength Medium Carbon steel
Se = Endurance strength
Se = ka,kb,kc,kd,ke se’
Se’= [0.566-9.68*10-5
*805]805 = 392.9
MPa
Ka = Surface finish (Figure 13-3 App D)
Kb = Size factor
Kc = Reliability (Figure 13-4 App D)
Kd = Temperature
Ke = Stress concentration
Ka = 0.35 (Forged)
Kb = 1 (Axial loading)
Kc = 0.814 (Reliability of 99%)
Kd = 1 (Temp <350 degrees)
Ke = 1/Kf
Kf = 1+q(Kt-1)
q = 1
Kt = d/w = 18/24.5 = 0.7346
h/w = 12.25/24.5 = 0.5
Kt = 0.22
Kf = 1+0.9(0.22-1)
Kf = 0.298
Se = (0.35)(1)(0.814)(1)(0.298)(392.9)
Se = 33.36 MPa
σm = Mean stress
σa = Stress amplitude
Equation 12-1
Equation 12-2
Using equation 12-1 and 12-2 to find the
mean and amplitude stress.
σm = 9.91 MPa
σa = 2.44 MPa
To find the factor of safety for fatigue using
equation 12-3.
Sut = 805 MPa
Se = 33.36 MPa
Equation 12-3
n = 11.7
To find the infinite number of cycles using
equation 12-4.
Equation 12-4
( )
Sut = 805 MPa
Se = 33.36 MPa
N = 1.68×106
cycles
86. 74
Fatigue Endurance Strength Low Alloy steel
Se = Endurance strength
Se = ka,kb,kc,kd,ke se’
Se’= [0.566-9.68*10-5
*1155]1155 = 524.59
MPa
Ka = Surface finish (Figure 13-3 App
D)
Kb = Size factor
Kc = Reliability (Figure 13-4 App
D)
Kd = Temperature
Ke = Stress concentration
Ka = 0.35 (Forged)
Kb = 1 (Axial loading)
Kc = 0.814 (Reliability of 99%)
Kd = 1 (Temp <350 degrees)
Ke = 1/Kf
Kf = 1+q(Kt-1)
q = 1
Kt = d/w = 18/24.5 = 0.7346
h/w = 12.25/24.5 = 0.5
Kt = 0.22
Kf = 1+0.9(0.22-1)
Kf = 0.298
Se = (0.35)(1)(0.814)(1)(0.298)(524.59)
Se = 44.54 MPa
σm = Mean stress
σa = Stress amplitude
Equation 12-5
Equation 12-6
Using equation 12-5 and 12-6 to find the
mean and amplitude stress.
σm = 9.91 MPa
σa = 2.44 MPa
To find the factor of safety for fatigue
using equation 12-7.
Sut = 1155 MPa
Se = 44.54 MPa
Equation 12-7
n = 15.78
To find the infinite number of cycles using
equation 12-8.
Equation 12-8
( )
N = 1.66×106
cycles
87. 75
Fatigue Endurance Strength High Carbon steel
Se = Endurance strength
Se = ka,kb,kc,kd,ke se’
Se’= [0.566-9.68*10-5
*1095]1095 = 503.70
MPa
Ka = Surface finish (Figure 13-3 App D)
Kb = Size factor
Kc = Reliability (Figure 13-4 App D)
Kd = Temperature
Ke = Stress concentration
Ka = 0.35 (Forged)
Kb = 1 (Axial loading)
Kc = 0.814 (Reliability of 99%)
Kd = 1 (Temp <350 degrees)
Ke = 1/Kf
Kf = 1+q(Kt-1)
q = 1
Kt = d/w = 18/24.5 = 0.7346
h/w = 12.25/24.5 = 0.5
Kt = 0.22
Kf = 1+0.9(0.22-1)
Kf = 0.298
Se = (0.35)(1)(0.814)(1)(0.298)(503.70)
Se = 42.76 MPa
σm = Mean stress
σa = Stress amplitude
Equation 12-9
Equation 12-10
Using equation 12-9 and 12-10 to find the
mean and amplitude stress.
σm = 9.91 MPa
σa = 2.44 MPa
To find the factor of safety for fatigue
using equation 12-11.
Sut = 1095 MPa
Se = 42.76 MPa
Equation 12-11
n = 15.13
To find the infinite number of cycles using
equation 12-12 .
Equation 12-12
( )
N = 1.67×106
cycles
88. 76
Fatigue Endurance Strength Titanium steel
Se = Endurance strength
Se = ka,kb,kc,kd,ke se’
Se’= [0.566-9.68*10-5
*975]975 = 459.83
MPa
Ka = Surface finish (Figure 13-3 App D)
Kb = Size factor
Kc = Reliability (Figure 13-4 App D)
Kd = Temperature
Ke = Stress concentration
Ka = 0.35 (Forged)
Kb = 1 (Axial loading)
Kc = 0.814 (Reliability of 99%)
Kd = 1 (Temp <350 degrees)
Ke = 1/Kf
Kf = 1+q(Kt-1)
q = 1
Kt = d/w = 18/24.5 = 0.7346
h/w = 12.25/24.5 = 0.5
Kt = 0.22
Kf = 1+0.9(0.22-1)
Kf = 0.298
Se = (0.35)(1)(0.814)(1)(0.298)(459.83)
Se = 39.04 MPa
σm = Mean stress
σa = Stress amplitude
Equation 12-13
Equation 12-14
Using equation 12-13 and 12-14 to find the
mean and amplitude stress.
σm = 9.91 MPa
σa = 2.44 MPa
To find the factor of safety for fatigue using
equation 12-15.
Sut = 975 MPa
Equation 12-15
n = 13.76
To find the infinite number of cycles using
equation 12-16.
Equation 12-16
( )
N = 1.67×106
cycles
89. 77
13.Appendix D
The results have to be verified to determine no mistakes were made during the analysis,
below are the calculations to determine if the reaction forces are correct.
Table 13-1 and Table 13-2 show the reaction forces from Ansys, the calculations for
verifying the results can be seen below each table.
Table 13-1: Reaction forces compression
THE FOLLOWING X,Y,Z SOLUTIONS ARE IN THE GLOBAL COORDINATE SYSTEM
NODE FX FY FZ
TOTAL VALUES
VALUE 500.18 866.33 -0.34421E-01
Fy = P*A
P=12.35 MPa
A=9*7.794228531
A=70.14805678 mm2
Fy = 866.33 N
Fx = 12.35*9*4.5
Fx = 500.18 N
Table 13-2: Reaction forces tension
THE FOLLOWING X,Y,Z SOLUTIONS ARE IN THE GLOBAL COORDINATE SYSTEM
NODE FX FY FZ
TOTAL VALUES
VALUE 302.54 -524.01 -0.26937E-05
Fy = 7.47*7.794228531*9
Fy = 524.01 N
Fx = 7.47*9*4.5
Fx = 302.54 N
90. 78
13.1 Verification Results Tension
To verify the results at the small end pin in tension with a force of 2096.61N.
σ = 7.51 MPa
Stress at the small end
Stress concentration
Using Figure A-15-12 to find the stress concentration at the pin, below are the calculations.
Kf = 1+q(Kt-1) (Figure 13-2 Appendix D)
q = 0.9 (Figure 13-1 Appendix D)
Kt = d/w = 18/24.5 = 0.7346
h/w = 12.25/24.5 = 0.5
Kt = 2.5
When a clearance exists multiply Kt by 50%
Kt = 2.5*1.5
Kt = 3.75
Kf = 1+0.9(3.75-1)
Kf = 3.475
σ = 3.475*7.51
σ = 26.09 MPa
Table 13-3: Percentage error (Tension)
Fillet size (mm) Section Stress Percentage Difference %
5 A-A 106.80 309.35
7 A-A 124.67 377.84
10 A-A 107.36 311.5
15 A-A 107.82 313.26
91. 79
13.2 Verification Results Compression
To verify the results with a compressive force of 3467.73N
σ = 12.43 MPa
Stress at the small end pin
Stress concentration
Using the Figure A-15-12 to find the stress concentration at the pin below.
Kf = 1+q(Kt-1) (Figure 13-2 appendix)
q = 0.9 (Figure 13-1 Appendix)
Kt = d/w = 18/24.5 = 0.7346
h/w = 12.25/24.5 = 0.5
Kt = 2.5
When a clearance exists multiply Kt by 50%
Kt = 2.5*1.5
Kt = 3.75
Kf = 1+0.9(3.75-1)
Kf = 3.475
σ = 3.475*12.43
σ = 43.19 MPa
Table 13-4 compares the stress results from Ansys to the calculated results. The results are
considerably different, the verification is not possible for this analysis due to the geometry
of the connecting rod.
Table 13-4: Percentage error (compression)
Fillet size (mm) Section Stress Percentage Difference %
5 A-A -23.89 44.68
7 A-A -23.250 46.17
10 A-A -12.65 70.71
15 A-A -36.88 14.61