0 th review
•
0 likes•193 views
The document proposes a system to remotely access the power windows of a car. It uses a GSM modem in the car that receives commands from a mobile phone. A second level of security coding protects the car from unauthorized access. The GSM modem is connected to a LIN slave microcontroller via serial communication registers. The LIN slave controller is connected to a LIN master controller via a LIN network. The LIN master operates the power window motor through a relay circuit when commanded by an authorized mobile phone. The system aims to solve the problem of accessing a locked car when keys are left inside.
Report
Share
Report
Share
Recommended
THEFT INTIMATION OF THE VEHICLE OVER GSM BY SMS WITH USER PROGRAMABLE NU...
This document describes a vehicle theft prevention project that uses a GSM modem and microcontroller to send SMS alerts to the vehicle owner when movement is detected, allowing the owner to remotely stop the engine. The system includes a GSM modem, microcontroller, relay, voltage regulator and battery. When theft is detected, the microcontroller sends an SMS to the owner via the GSM modem. If the owner replies with the word "stop", the microcontroller activates a relay to disconnect the ignition and stop the vehicle.
Gsm controlled robot abstract
This document describes a GSM controlled robot that can be operated from anywhere using a mobile phone. The robot uses an Atmega8 microcontroller and transmits live video over the internet with no range limit for control. Potential applications include remote surveillance, security monitoring, rescue operations, and medical observation.
gsm based home automation
The document describes a home appliance control system based on GSM network technology that allows users to remotely control appliances via SMS. A microcontroller receives SMS commands and uses a relay circuit to operate appliances. Key advantages are ubiquitous access, wireless operation for adaptability and cost-effectiveness, and power conservation. Limitations include the receiver needing a constant power supply and cellular signal to operate connected devices.
Group-3
This presentation summarizes a student project on developing a home automation and security system using GSM technology. It was prepared by three students for their department supervisor. The presentation outlines the objectives, which are to develop a wireless home automation system using GSM to remotely monitor and control devices. It describes the basic working of the system with a microcontroller receiving SMS commands from a mobile phone to operate devices. The hardware and software components used are also summarized, along with the advantages of flexibility, security and power savings enabled by the remote control functionality.
MICRO CONTROLLER BASED ROBOT FOR ANTI INFILTRATION
This document describes a microcontroller-based robot designed for unmanned anti-infiltration and remote security using GSM messaging. The objective is to stop infiltrators with a simple mechatronic robot using a PIC microcontroller. It introduces an anti-infiltration robot that can defend borders without human intervention at a low cost. The proposed system includes a gear disc-gun mount, batteries, air compressor, PIC microcontroller, IR sensors, and GSM modem to identify and engage intruders while alerting command posts through SMS messages. The robot is intended to maximize security along borders through unmanned operation in varied terrain and weather conditions.
gsm based security system
suppose this security system is fitted in your car . If a thief breaks in and tries to drive away your car then he/she have enter the code for ignition .If the code mismatches then it will send a message to the proprietor's cell "security breach".By this we will come to know that someone is trying to steal your car.
"THAT IS THE IDEA OF THE PROJECT"
Vehicle 441
This document discusses several projects involving GPS and GSM systems for vehicle theft prevention. It describes how GPS is used to track the exact location of a vehicle and GSM is used to send location messages to the vehicle owner if theft is detected. The projects allow owners to remotely deactivate ignitions if needed. Precise vehicle locations are retrieved and sent via SMS along with potential to integrate additional sensors and develop more advanced anti-theft and tracking systems.
3 gpp r15-5g-sim-card-definition-final
The document defines three types of 5G SIM cards: transitional SIM, recommended 5G SIM, and low power SIM. The recommended 5G SIM leverages the full capabilities of 5G, provides backward compatibility, and future-proofing. It helps mobile operators ensure quality of experience, protect subscriber privacy, extend battery life, deliver IP services, optimize network resources, and enhance security. The document recommends adoption of the recommended 5G SIM at 5G launch.
Recommended
THEFT INTIMATION OF THE VEHICLE OVER GSM BY SMS WITH USER PROGRAMABLE NU...
This document describes a vehicle theft prevention project that uses a GSM modem and microcontroller to send SMS alerts to the vehicle owner when movement is detected, allowing the owner to remotely stop the engine. The system includes a GSM modem, microcontroller, relay, voltage regulator and battery. When theft is detected, the microcontroller sends an SMS to the owner via the GSM modem. If the owner replies with the word "stop", the microcontroller activates a relay to disconnect the ignition and stop the vehicle.
Gsm controlled robot abstract
This document describes a GSM controlled robot that can be operated from anywhere using a mobile phone. The robot uses an Atmega8 microcontroller and transmits live video over the internet with no range limit for control. Potential applications include remote surveillance, security monitoring, rescue operations, and medical observation.
gsm based home automation
The document describes a home appliance control system based on GSM network technology that allows users to remotely control appliances via SMS. A microcontroller receives SMS commands and uses a relay circuit to operate appliances. Key advantages are ubiquitous access, wireless operation for adaptability and cost-effectiveness, and power conservation. Limitations include the receiver needing a constant power supply and cellular signal to operate connected devices.
Group-3
This presentation summarizes a student project on developing a home automation and security system using GSM technology. It was prepared by three students for their department supervisor. The presentation outlines the objectives, which are to develop a wireless home automation system using GSM to remotely monitor and control devices. It describes the basic working of the system with a microcontroller receiving SMS commands from a mobile phone to operate devices. The hardware and software components used are also summarized, along with the advantages of flexibility, security and power savings enabled by the remote control functionality.
MICRO CONTROLLER BASED ROBOT FOR ANTI INFILTRATION
This document describes a microcontroller-based robot designed for unmanned anti-infiltration and remote security using GSM messaging. The objective is to stop infiltrators with a simple mechatronic robot using a PIC microcontroller. It introduces an anti-infiltration robot that can defend borders without human intervention at a low cost. The proposed system includes a gear disc-gun mount, batteries, air compressor, PIC microcontroller, IR sensors, and GSM modem to identify and engage intruders while alerting command posts through SMS messages. The robot is intended to maximize security along borders through unmanned operation in varied terrain and weather conditions.
gsm based security system
suppose this security system is fitted in your car . If a thief breaks in and tries to drive away your car then he/she have enter the code for ignition .If the code mismatches then it will send a message to the proprietor's cell "security breach".By this we will come to know that someone is trying to steal your car.
"THAT IS THE IDEA OF THE PROJECT"
Vehicle 441
This document discusses several projects involving GPS and GSM systems for vehicle theft prevention. It describes how GPS is used to track the exact location of a vehicle and GSM is used to send location messages to the vehicle owner if theft is detected. The projects allow owners to remotely deactivate ignitions if needed. Precise vehicle locations are retrieved and sent via SMS along with potential to integrate additional sensors and develop more advanced anti-theft and tracking systems.
3 gpp r15-5g-sim-card-definition-final
The document defines three types of 5G SIM cards: transitional SIM, recommended 5G SIM, and low power SIM. The recommended 5G SIM leverages the full capabilities of 5G, provides backward compatibility, and future-proofing. It helps mobile operators ensure quality of experience, protect subscriber privacy, extend battery life, deliver IP services, optimize network resources, and enhance security. The document recommends adoption of the recommended 5G SIM at 5G launch.
Pir and gsm based house security system
This document describes a PIR and GSM based home security system. The system uses a sensor to detect intruders and notifies the homeowner through an alarm and SMS message. It continuously monitors the sensor status and automatically sends SMS alerts to the user if the sensor is triggered. The system aims to provide security for homes, banks, and companies through detection and remote notification capabilities.
Final nc paper
This document describes a microcontroller-based interface to analyze data errors in a ship network. It includes sections on introduction, ATM switches, network interface units (NIU), the functions of the man-machine interface (MMI), a block diagram, hardware specifications, practical implementation, and limitations. The MMI is used to display error messages from the NIU, status information, and initiate tests. It was implemented using an 80C51 microcontroller programmed in Keil software to read messages from a NIU simulator over serial communication.
Gps vehicle theft identification and tracking and control
This document describes a microcontroller-based GPS and GSM tracking system. It includes a block diagram showing the main components: a microcontroller, GPS modem, GSM modem, LCD display, sensor, ADC and power supply. It provides details on the 8051 microcontroller, MEMS sensors, and the importance of GPS and GSM networks for location tracking. It also lists advantages like security, remote access and applications in vehicles, ships and tracking systems.
Accident reporting system using mems
This document describes a MEMS-controlled accident reporting system that uses an accelerometer and GPS to detect vehicle accidents. When an accident occurs, the accelerometer detects vibrations and sends a signal to an ARM controller. The microcontroller then enables an airbag and sends a message with the accident location from the GPS to emergency contacts via GSM. The system aims to reduce response times and save lives by quickly notifying emergency services and relatives of accidents.
ShawnTech MAS
ShawnTech's Managed Access System (MAS) systematically manages communications within correctional facilities to stop unauthorized devices while allowing authorized communications. The scalable system covers all common cellular protocols and frequencies used in the US in compliance with communications regulations. Network operations are monitored 24/7 through their network operations center to provide intelligence reports and ensure reliable system operations through preventative maintenance. The MAS uses a distributed antenna system and fiber infrastructure to systematically control communications across a facility based on designed coverage levels for different areas.
Yuva Home automation project
This document describes a GSM-based home automation system that allows users to remotely control and monitor home appliances via SMS after authentication. The proposed system aims to overcome issues with existing manual systems by allowing remote control and scheduling of devices to save time and energy. The system uses a GSM modem connected to a microcontroller to send and receive SMS commands to control relays and devices like lights and fans. It provides advantages like low cost and global access but has delays due to mobile networks. The system could be enhanced with security cameras for remote monitoring.
Gsm based home(ppt)
This document provides an overview of a project to create a home automation system using GSM technology. The system would allow users to control home appliances via SMS from their mobile phone. It discusses the motivation, objectives, basic working, components, costs, timeline, and pros and cons of the system. The objectives are to enable remote control of appliances without being physically present and reduce power and time wastage. The estimated cost is 3,814 Rs. and the timeline outlines tasks from feasibility to testing over 6 months.
Vehicle tracking and locking system based on GSM and GPS
This document provides an overview of a vehicle tracking and locking system based on GPS and GSM technologies. The system puts the vehicle in sleep mode when handled by the owner and active mode when theft is detected. When theft occurs, the system sends an SMS to the microcontroller to stop the engine and lock the doors. The location of the vehicle can then be easily tracked. The system was implemented and tested successfully.
anti theft alarm for bikes by vinod and venu
This document summarizes a student project that designed an anti-theft alarm system for bikes. The circuit uses a 555 timer, 7805 voltage regulator, 7473 JK flip-flop, and LM311 comparator. It has a transmitter section with an IR LED attached to the front mudguard and a receiver section with an IR sensor. When the mudguard is moved, the sensor detects the IR signal and sounds the bike horn through a relay. The system provides security for vehicles in a low-cost and effective way.
VEHICLE SPEED CONTROL AND ACCIDENT AVOIDANCE SYSTEM BASED ON ARM M4 MICROPROC...
VEHICLE SPEED CONTROL AND ACCIDENT AVOIDANCE SYSTEM BASED ON ARM M4 MICROPROC...Md. Raseduzzaman Ruman
This document describes a vehicle speed control and accident avoidance system based on an ARM M4 microprocessor. The system uses ultrasonic sensors to detect obstacles in front of and behind a vehicle. It is designed to automatically control vehicle speed and brake to avoid accidents at high speeds. The system was simulated, implemented on a prototype vehicle using a ARM M4 processor, ultrasonic sensors, LCD display, buzzer, and braking system. It was able to detect obstacles and smoothly apply the brakes. The system aims to save pedestrians' lives. Future work may include improving the braking algorithm, using higher range sensors, and modifying the vehicle.44CON 2014 - GreedyBTS: Hacking Adventures in GSM, Hacker Fantastic
44CON 2014 - GreedyBTS: Hacking Adventures in GSM, Hacker Fantastic
There are over 2.9 BILLION subscribers on GSM networks today. How many of these subscribers are susceptible to trivial attacks that can leave phone calls, text messages and web surfing habits accessible to an attacker? This talk intends to discuss the reasons why GSM networks are still vulnerable today and demonstrate attack tools that might make you re-think how you handle sensitive data via your phone. The presenter will discuss his own experience of analysing GSM environments and provide a demonstration of GreedyBTS which can be used to compromise a targets phone calls, messaging and web surfing habits. Mobile Phones will be harmed during this presentation.
Digital Notice Board
This document describes a multi-notice display board system using GSM technology. It is summarized as follows:
The system allows wireless control of multiple notice boards using an AT89S52 microcontroller and GSM modem. Notices can be sent individually to boards A and B or to both boards simultaneously. The microcontroller interfaces with a 20x4 LCD display on each board to show messages. The system provides a low-cost and low-power way to remotely manage multiple display boards for places like colleges, hospitals, and stations.
6d5504
This document describes the design of a vehicle accident alarm system using GSM and GPS technology. The system uses an accelerometer to detect if an accident has occurred, then sends alert messages via GSM to emergency contacts and tracks the vehicle's location using GPS to help rescuers locate the accident site quickly. The system architecture includes components like an ARM7 microcontroller, GPS and GSM modules, and an LCD display. The goal is to shorten emergency response times and save lives in the event of a vehicle accident.
Gsm based home automation ppt
This document describes a home appliance control system based on GSM network technology. The system allows users to remotely control and monitor home appliances and security via SMS messages sent from their mobile device to a GSM modem connected to a PC system in the home. When intrusions are detected by the system, such as at the main gate, entrance door, or windows, an SMS alert is generated and sent to the user's mobile phone. The GSM-based system provides an affordable way to remotely control home automation and security compared to previous methods. Future improvements could integrate the PC and GSM modem into a single enclosed device with its own UPS and charging system.
Home automation and Digital notice board using android app
This document describes a home automation system using an LPC2148 microcontroller, GSM modem, relays, and an Android application. The system allows users to control appliances and view a digital notice board remotely using the Android app via GSM. The LPC2148 microcontroller interfaces with the GSM modem to receive control messages and trigger relays to operate appliances. The system provides a low-cost, flexible, and secure remote automation solution.
Improve Process Control Security Using Annunciators as Watchers
Software-based systems are vulnerable to cyber attacks. Most of the industrial control networks (CAN, PROFI, Control Area, Ethernet and RS485) connect to the internet or other computer networks which are not fully protected from hackers and viruses. Present day industrial DCS/PLC control systems come with redun- dancy systems to eliminate shutdowns in case of DCS/PLC hardware failures. However, this does not protect your DCS/PLC system from any type of cyber attack. Without proper protection, the safety and/or operation of your plant or business are put at great risk.
Presentation
The document discusses Telindus (Cellstack) Video Surveillance systems which use modular encoder and decoder cards on shelves to connect up to 54 cameras. The systems can use MJPEG or MPEG2 encoding and decode video transmitted over ATM or Gigabit Ethernet networks with typical delays of 60-200ms. They support point-to-multipoint connections, independent serial control of devices, audio capabilities, and can be managed by the CellStack Manager software. Major implementations included surveillance networks for airports, highways, transit systems, ports, and other industrial facilities.
5 steps-to-make-a-website
The document lists various domain name extensions for the company "yourcompany" including .com, .net, .org, .gov, .edu, .mil, .info, and country-specific domains. It then compares the capabilities of developing websites using CMS systems like Wordpress versus custom coding. Finally, it outlines some online marketing strategies including blogging, forums, chats, booking, articles, surveys, registration forms, photo galleries, and press releases.
Understanding Internet marketing
The document outlines an online eMarketing model that utilizes various digital marketing strategies including search engine optimization, social media optimization, email marketing, display advertising, and affiliate marketing. Traffic is generated through organic search, paid search, social media, direct mailers, and reciprocal linking. Leads are captured on the website and followed up via phone and email. Performance is tracked through online analytics. The model is meant to drive qualified traffic and leads to a company's website and conversion goals.
Dossier
Dossier de mis trabajos en conservación y restauración y pintura.
Diseñado por Virginia Lázaro Villa
http://virginialazarovilla.blogspot.com.es/
Uso educativo del twitter
Este documento describe una actividad en la que los estudiantes usarán Twitter para analizar y proponer soluciones a problemas ambientales. La actividad consta de 4 fases: 1) investigar problemas ambientales, 2) votar por el problema más importante, 3) proponer soluciones e ideas, y 4) votar por la mejor idea. Los estudiantes serán evaluados en base a su uso de Twitter, investigación, creatividad y cumplimiento de plazos.
More Related Content
What's hot
Pir and gsm based house security system
This document describes a PIR and GSM based home security system. The system uses a sensor to detect intruders and notifies the homeowner through an alarm and SMS message. It continuously monitors the sensor status and automatically sends SMS alerts to the user if the sensor is triggered. The system aims to provide security for homes, banks, and companies through detection and remote notification capabilities.
Final nc paper
This document describes a microcontroller-based interface to analyze data errors in a ship network. It includes sections on introduction, ATM switches, network interface units (NIU), the functions of the man-machine interface (MMI), a block diagram, hardware specifications, practical implementation, and limitations. The MMI is used to display error messages from the NIU, status information, and initiate tests. It was implemented using an 80C51 microcontroller programmed in Keil software to read messages from a NIU simulator over serial communication.
Gps vehicle theft identification and tracking and control
This document describes a microcontroller-based GPS and GSM tracking system. It includes a block diagram showing the main components: a microcontroller, GPS modem, GSM modem, LCD display, sensor, ADC and power supply. It provides details on the 8051 microcontroller, MEMS sensors, and the importance of GPS and GSM networks for location tracking. It also lists advantages like security, remote access and applications in vehicles, ships and tracking systems.
Accident reporting system using mems
This document describes a MEMS-controlled accident reporting system that uses an accelerometer and GPS to detect vehicle accidents. When an accident occurs, the accelerometer detects vibrations and sends a signal to an ARM controller. The microcontroller then enables an airbag and sends a message with the accident location from the GPS to emergency contacts via GSM. The system aims to reduce response times and save lives by quickly notifying emergency services and relatives of accidents.
ShawnTech MAS
ShawnTech's Managed Access System (MAS) systematically manages communications within correctional facilities to stop unauthorized devices while allowing authorized communications. The scalable system covers all common cellular protocols and frequencies used in the US in compliance with communications regulations. Network operations are monitored 24/7 through their network operations center to provide intelligence reports and ensure reliable system operations through preventative maintenance. The MAS uses a distributed antenna system and fiber infrastructure to systematically control communications across a facility based on designed coverage levels for different areas.
Yuva Home automation project
This document describes a GSM-based home automation system that allows users to remotely control and monitor home appliances via SMS after authentication. The proposed system aims to overcome issues with existing manual systems by allowing remote control and scheduling of devices to save time and energy. The system uses a GSM modem connected to a microcontroller to send and receive SMS commands to control relays and devices like lights and fans. It provides advantages like low cost and global access but has delays due to mobile networks. The system could be enhanced with security cameras for remote monitoring.
Gsm based home(ppt)
This document provides an overview of a project to create a home automation system using GSM technology. The system would allow users to control home appliances via SMS from their mobile phone. It discusses the motivation, objectives, basic working, components, costs, timeline, and pros and cons of the system. The objectives are to enable remote control of appliances without being physically present and reduce power and time wastage. The estimated cost is 3,814 Rs. and the timeline outlines tasks from feasibility to testing over 6 months.
Vehicle tracking and locking system based on GSM and GPS
This document provides an overview of a vehicle tracking and locking system based on GPS and GSM technologies. The system puts the vehicle in sleep mode when handled by the owner and active mode when theft is detected. When theft occurs, the system sends an SMS to the microcontroller to stop the engine and lock the doors. The location of the vehicle can then be easily tracked. The system was implemented and tested successfully.
anti theft alarm for bikes by vinod and venu
This document summarizes a student project that designed an anti-theft alarm system for bikes. The circuit uses a 555 timer, 7805 voltage regulator, 7473 JK flip-flop, and LM311 comparator. It has a transmitter section with an IR LED attached to the front mudguard and a receiver section with an IR sensor. When the mudguard is moved, the sensor detects the IR signal and sounds the bike horn through a relay. The system provides security for vehicles in a low-cost and effective way.
VEHICLE SPEED CONTROL AND ACCIDENT AVOIDANCE SYSTEM BASED ON ARM M4 MICROPROC...
VEHICLE SPEED CONTROL AND ACCIDENT AVOIDANCE SYSTEM BASED ON ARM M4 MICROPROC...Md. Raseduzzaman Ruman
This document describes a vehicle speed control and accident avoidance system based on an ARM M4 microprocessor. The system uses ultrasonic sensors to detect obstacles in front of and behind a vehicle. It is designed to automatically control vehicle speed and brake to avoid accidents at high speeds. The system was simulated, implemented on a prototype vehicle using a ARM M4 processor, ultrasonic sensors, LCD display, buzzer, and braking system. It was able to detect obstacles and smoothly apply the brakes. The system aims to save pedestrians' lives. Future work may include improving the braking algorithm, using higher range sensors, and modifying the vehicle.44CON 2014 - GreedyBTS: Hacking Adventures in GSM, Hacker Fantastic
44CON 2014 - GreedyBTS: Hacking Adventures in GSM, Hacker Fantastic
There are over 2.9 BILLION subscribers on GSM networks today. How many of these subscribers are susceptible to trivial attacks that can leave phone calls, text messages and web surfing habits accessible to an attacker? This talk intends to discuss the reasons why GSM networks are still vulnerable today and demonstrate attack tools that might make you re-think how you handle sensitive data via your phone. The presenter will discuss his own experience of analysing GSM environments and provide a demonstration of GreedyBTS which can be used to compromise a targets phone calls, messaging and web surfing habits. Mobile Phones will be harmed during this presentation.
Digital Notice Board
This document describes a multi-notice display board system using GSM technology. It is summarized as follows:
The system allows wireless control of multiple notice boards using an AT89S52 microcontroller and GSM modem. Notices can be sent individually to boards A and B or to both boards simultaneously. The microcontroller interfaces with a 20x4 LCD display on each board to show messages. The system provides a low-cost and low-power way to remotely manage multiple display boards for places like colleges, hospitals, and stations.
6d5504
This document describes the design of a vehicle accident alarm system using GSM and GPS technology. The system uses an accelerometer to detect if an accident has occurred, then sends alert messages via GSM to emergency contacts and tracks the vehicle's location using GPS to help rescuers locate the accident site quickly. The system architecture includes components like an ARM7 microcontroller, GPS and GSM modules, and an LCD display. The goal is to shorten emergency response times and save lives in the event of a vehicle accident.
Gsm based home automation ppt
This document describes a home appliance control system based on GSM network technology. The system allows users to remotely control and monitor home appliances and security via SMS messages sent from their mobile device to a GSM modem connected to a PC system in the home. When intrusions are detected by the system, such as at the main gate, entrance door, or windows, an SMS alert is generated and sent to the user's mobile phone. The GSM-based system provides an affordable way to remotely control home automation and security compared to previous methods. Future improvements could integrate the PC and GSM modem into a single enclosed device with its own UPS and charging system.
Home automation and Digital notice board using android app
This document describes a home automation system using an LPC2148 microcontroller, GSM modem, relays, and an Android application. The system allows users to control appliances and view a digital notice board remotely using the Android app via GSM. The LPC2148 microcontroller interfaces with the GSM modem to receive control messages and trigger relays to operate appliances. The system provides a low-cost, flexible, and secure remote automation solution.
Improve Process Control Security Using Annunciators as Watchers
Software-based systems are vulnerable to cyber attacks. Most of the industrial control networks (CAN, PROFI, Control Area, Ethernet and RS485) connect to the internet or other computer networks which are not fully protected from hackers and viruses. Present day industrial DCS/PLC control systems come with redun- dancy systems to eliminate shutdowns in case of DCS/PLC hardware failures. However, this does not protect your DCS/PLC system from any type of cyber attack. Without proper protection, the safety and/or operation of your plant or business are put at great risk.
Presentation
The document discusses Telindus (Cellstack) Video Surveillance systems which use modular encoder and decoder cards on shelves to connect up to 54 cameras. The systems can use MJPEG or MPEG2 encoding and decode video transmitted over ATM or Gigabit Ethernet networks with typical delays of 60-200ms. They support point-to-multipoint connections, independent serial control of devices, audio capabilities, and can be managed by the CellStack Manager software. Major implementations included surveillance networks for airports, highways, transit systems, ports, and other industrial facilities.
What's hot (17)
Gps vehicle theft identification and tracking and control
Gps vehicle theft identification and tracking and control
Vehicle tracking and locking system based on GSM and GPS
Vehicle tracking and locking system based on GSM and GPS
VEHICLE SPEED CONTROL AND ACCIDENT AVOIDANCE SYSTEM BASED ON ARM M4 MICROPROC...
VEHICLE SPEED CONTROL AND ACCIDENT AVOIDANCE SYSTEM BASED ON ARM M4 MICROPROC...
44CON 2014 - GreedyBTS: Hacking Adventures in GSM, Hacker Fantastic
44CON 2014 - GreedyBTS: Hacking Adventures in GSM, Hacker Fantastic
Home automation and Digital notice board using android app
Home automation and Digital notice board using android app
Improve Process Control Security Using Annunciators as Watchers
Improve Process Control Security Using Annunciators as Watchers
Viewers also liked
5 steps-to-make-a-website
The document lists various domain name extensions for the company "yourcompany" including .com, .net, .org, .gov, .edu, .mil, .info, and country-specific domains. It then compares the capabilities of developing websites using CMS systems like Wordpress versus custom coding. Finally, it outlines some online marketing strategies including blogging, forums, chats, booking, articles, surveys, registration forms, photo galleries, and press releases.
Understanding Internet marketing
The document outlines an online eMarketing model that utilizes various digital marketing strategies including search engine optimization, social media optimization, email marketing, display advertising, and affiliate marketing. Traffic is generated through organic search, paid search, social media, direct mailers, and reciprocal linking. Leads are captured on the website and followed up via phone and email. Performance is tracked through online analytics. The model is meant to drive qualified traffic and leads to a company's website and conversion goals.
Dossier
Dossier de mis trabajos en conservación y restauración y pintura.
Diseñado por Virginia Lázaro Villa
http://virginialazarovilla.blogspot.com.es/
Uso educativo del twitter
Este documento describe una actividad en la que los estudiantes usarán Twitter para analizar y proponer soluciones a problemas ambientales. La actividad consta de 4 fases: 1) investigar problemas ambientales, 2) votar por el problema más importante, 3) proponer soluciones e ideas, y 4) votar por la mejor idea. Los estudiantes serán evaluados en base a su uso de Twitter, investigación, creatividad y cumplimiento de plazos.
Avoiding test hell
We are entering a world where everything must be done quicker. You must deliver code faster. You must deploy faster. How can you deliver and deploy faster without compromising your professionalism? How can you be sure you are delivering what your client has asked you?
In short, testing is the only way to be sure you’re delivering what someone asked you to. Often we use BDD Tools such as FitNesse which gained popularity over the recent years
There are a number of integration / BDD test tools out there that help you deliver a high quality software through tests. Its easy to pick up any tool from just their tutorials and start writing tests. But as I found out the hard way, this can quickly spiral into a state where the tests are giving you and your team hell and are worth less than the value the tests are delivering.
Using FitNesse and Junit as examples, I will share things that I have learnt working on large enterprise and vendor systems and help you avoid your own path to hell.
Drug dispensing contact lenses a reality
...Eye care providers are readily familiar with the vision and cosmetic benefits that contact lenses
afford over spectacles. Most of these clinicians are also aware of the more medical applications of such devices in the form of bandage contact lenses and orthokeratology. However, another important medical use for contact lenses
is nearing reality - pharmaceutical dispensing. Read more.....
Análisis DAFO de una experiencia de fomento de competencias STEM
Se presenta el análisis DAFO de la integración de la aplicación Apps Matemáticas para Ipad para el aprendizaje de Matemáticas en 1° de ESO
CV TemplateREV [1]
B. Roberts is a British senior integrity consultant with over 40 years of experience in inspection engineering. He has worked extensively offshore and onshore, managing inspection teams and providing technical leadership. His areas of expertise include inspection of offshore and onshore facilities for oil and gas companies, implementing risk-based inspection programs, and developing integrity management strategies. He holds multiple engineering qualifications and inspector certifications.
Hydrogels and silicone hydrogels
This document discusses hydrogel and silicone hydrogel contact lenses. Hydrogel lenses have advantages like initial comfort but disadvantages such as poor oxygen transmission and dryness. Silicone hydrogel lenses have higher oxygen permeability which makes them more suitable for extended wear and reduces risks of complications. Silicone hydrogels are more expensive than hydrogels but provide benefits like increased comfort, rigidity for easy handling, and surface wettability. The document recommends silicone hydrogel lenses for patients who wear contacts long hours or in low humidity environments.
Scientific measurement protocols 1
This document outlines scientific measurement protocols for various types of eyewear, including single vision, bifocal, and progressive lenses. It discusses important measurements like interpupillary distance, fitting height, lens centration, and frame adjustments. Proper protocols are described for patient selection, frame fitting, lens marking, quality checks, and delivering instructions to ensure accurate eyewear prescriptions. Following standardized procedures helps optical professionals provide patients with well-fitted lenses that optimize their vision.
Sports injuries & its prevention
The kind of injuries that most commonly occur during sports or exercise.
Some sports injuries result from accidents: others due to poor training practices, improper equipment or insufficient warm-up or stretching.
While it is possible to injure any part of the body when playing sports, the term sports injuries is commonly used to refer to injuries of the musculoskeletal system.
Viewers also liked (13)
Análisis DAFO de una experiencia de fomento de competencias STEM
Análisis DAFO de una experiencia de fomento de competencias STEM
Similar to 0 th review
Eprojectprojectfinalreportgsmmonitoringcontrollingofdevicesusinggsm 090811012...
This document describes a system to remotely monitor and control devices using GSM technology. The system uses a GSM transmitter and receiver along with a microcontroller. Users can send SMS messages to turn devices on or off, check statuses, and receive notifications. The system provides advantages like remote monitoring and control. Potential applications include home, office, and industrial automation as well as agricultural equipment control and security systems.
multiple input control by sms using GSM technology
This document presents a project to develop a home appliance control system using a microcontroller, GSM network, and SMS messages. The system aims to allow remote control of appliances in a cheap and simple way compared to existing wireless solutions. The major components are an AT89S52 microcontroller, GSM modem, relay circuits, and interfaces to appliances. The microcontroller communicates with the GSM modem via a serial interface to send and receive SMS commands to control relays and appliances from a remote cell phone. The system is designed for applications like appliance control, security systems, and home entertainment control from outside the home.
seminar.pptx
This document describes a wireless communication system to remotely monitor and control equipment using a GSM network. It consists of a transmitter and receiver connected by a GSM modem. The transmitter is a mobile phone that sends SMS codes to control relays and devices. The receiver includes a microcontroller, GSM modem, relays, and devices. It receives SMS codes and uses the microcontroller to operate the relays and control devices like fans and lamps. The system allows remote monitoring and control of devices from anywhere through simple SMS commands. It has applications in home, office, and industrial automation.
ELECTRONIC PROTECTION FOR EXAM PAPER LEAKAGE
At Softroniics we provide job oriented training for freshers in IT sector. We are Pioneers in all leading technologies like Android, Java, .NET, PHP, Python, Embedded Systems, Matlab, NS2, VLSI etc. We are specializiling in technologies like Big Data, Cloud Computing, Internet Of Things (iOT), Data Mining, Networking, Information Security, Image Processing, Mechanical, Automobile automation and many other. We are providing long term and short term internship also.
We are providing short term in industrial training, internship and inplant training for Btech/Bsc/MCA/MTech students. Attached is the list of Topics for Mechanical, Automobile and Mechatronics areas.
MD MANIKANDAN-9037291113,04954021113
softroniics@gmail.com
www.softroniics.com
DTMF based Different Load control
This document describes a DTMF (Dual Tone Multi Frequency) based load control system. The system uses a DTMF decoder interfaced with a microcontroller to receive DTMF tones from a cell phone and control loads remotely. When a key is pressed on the cell phone, the corresponding DTMF tones are received by the decoder and converted to digital codes. The microcontroller then turns relays on/off to actuate loads according to the received commands, allowing remote control of industrial and agricultural equipment or household devices spread over a large area.
Security system using Arduino
The objective of this project is to design and develop a wireless communication link to monitor our organizations that require high security like Banks , Offices etc.
111ei0254ppt8thsem
This document outlines an embedded system project to monitor vehicular movement in mining sites in real-time. It proposes using a vehicle module containing an Arduino, GPS, and GSM modem to track vehicle location and transmit data via GSM. A switchover module would enable communication between short-range radio and GSM based on location. Work completed includes developing the vehicle and switchover modules along with control room software. Future work involves PCB design and adding additional features. Diagrams show the system design and layouts are included along with results from testing the GSM module and sample web interfaces.
accident detection tech seminar ppt.pptx
This document describes a mini project on a GSM based home automation system. The key components of the system include an Arduino Uno, GSM module, relay, LCD display, and mobile phone. The system allows users to remotely switch household appliances on and off using the GSM module and Arduino. It provides a low cost and reliable way to automate and control appliances in the home from a mobile phone.
IMCC.pptx
The document discusses the advantages of an Intelligent Motor Control Centre (IMCC) over a traditional MCC. An IMCC uses automation technologies like PLCs, HMIs, and SIMOCODs to allow for easier motor protection setting changes, improved parameter monitoring, fault/trip histories, and communication over a single Profibus cable. It also describes some common problems that can occur with routine IMCC operations and provides an overview of how the SIMOCOD software is used to configure feeders from an HMI.
land rover robot control using GSM technology
This document presents a project on a land rover robot that uses GSM technology to control the robot remotely. A group of 5 students developed the robot under the guidance of faculty. The robot uses a microcontroller, GSM modem, motors and other components. The robot can be controlled remotely by sending text messages to move forward, backward, left or right. The document describes the components, working, advantages, applications and future scope of the remote controlled robot.
substation monitoring and control system
system of operation and control of grid system which is controlled by a bluetooth and gprs. Design for a project to the electrical department.
fault monitring system
This document summarizes a student project on a GSM-based fault monitoring system for cell phone towers. The system uses a GSM modem and microcontroller to detect faults and send SMS alerts to supervisors. It allows remote monitoring of power grids and industries without needing on-site staff. The project aims to design an indication system for overvoltage and over-current faults. Key components are a GSM modem to connect to the mobile network and an 89S51 microcontroller. The system provides long-life, low-cost monitoring without maintenance through SMS alerts. It has applications for power grids, factories, and home automation.
IRJET-A Comparative Study of use of the Library and the Internet as Sources o...
This document describes a password protected interactive voice response system to remotely control a three-phase motor using a GSM modem and microcontroller. The system allows a user to call in, enter a password, and then select to turn the motor on or off by pressing buttons on their phone. It uses pre-recorded voice prompts to interact with the user. The system has applications for remotely controlling equipment like motors in agricultural settings from anywhere via a mobile phone call. It aims to provide a low-cost and user-friendly solution for remote control of three-phase motors with voice confirmation of commands.
MY RESUME
This document is a resume for Amit Phapale summarizing his experience and qualifications for an engineering role in industrial automation. It outlines his current role as a project engineer at Hi-Tech Control Systems where he is responsible for PLC programming, HMI development, panel testing and commissioning. It also lists his academic credentials including a diploma in electronics and telecommunications engineering, and details several machine-based projects he has worked on involving PLC programming and commissioning of drives and control panels for applications like printing, lamination, and slitting.
Bits pilani solar power fencing by blaze automation
The document outlines security and surveillance requirements and proposals for BITS Pilani - Hyderabad Campus. It discusses various perimeter security fencing options including basic, mid-range, and advanced systems with integrated CCTV. Budget requirements are provided for each level, ranging from Rs. 33-36 lakhs for basic fencing to Rs. 134-140 lakhs for an advanced system. Key components and features of each are described, including centralized monitoring, zone identification, health monitoring, and intrusion detection capabilities. IP CCTV integration and network video recorder options are also summarized.
Advanced Automation System in Industrial Applications Using PIC Microcontrol...
The main aim of this paper is to design and develop an advanced automation system in the
industries. In this technique we are using the GSM modem which have the SIM card present in it, the
user can send message on the 10 digit SIM number using the cell phone from any part of the world. The
micro controller is programmed using the embedded C. when the user will send the message to a
particular device that particular device will be on or we can also off the device. Example if the motor is
in over voltage, under voltage, over current in that time the microcontroller will trip the circuit and give
the message feedback to the user. The micro controller will read the temp from the sensor and it will
display the same on the LCD when the incoming temp crosses the set limit the micro controller will turn
OFF the device and will send the message to owner using the SIM card present in the GSM modem. We
can also check the continuous status of the device.
Syngenta solar power fencing by blaze automation
The document outlines a presentation for a solar power fencing and CCTV integration system. It discusses three categories of solar power fencing systems from basic to advanced. The advanced system includes integration with CCTV cameras, wireless IP surveillance, and central monitoring station equipment. Budget requirements are provided for each category, with the basic system costing around Rs. 33-36 lakh, mid-range around Rs. 58.8-62 lakh, and advanced around Rs. 134-140 lakh. Safety requirements are also outlined.
SICAM FCG-Fault Collector Gateway
The SICAM Fault Collector Gateway (FCG) receives fault information from the SICAM Fault Sensor Indicator (FSI) via short-range radio, and transmits this information to the control center using various communication protocols; it provides inputs and outputs to interface with other devices and can be configured locally via web interface or remotely through GPRS; the FCG acts as a gateway between the FSIs and control center to enable communication of faults and sensor data.
Multiuser sms based microcontroller wireless electronic board
This document describes a wireless SMS-based microcontroller system for displaying electronic notices. The system uses an AT89C52 microcontroller interfaced with a GSM modem via a MAX232 level converter. The microcontroller is programmed using Embedded C and interfaces with a PC using Visual Basic. Messages entered on the PC are sent via GSM and displayed on a 16x2 LCD screen. The system provides a wireless solution to remotely update notices with low errors and maintenance.
Iirdem implementation of smart homes and industrial automation system with se...
The document proposes a smart home and industrial automation system that allows users to control appliances remotely using a mobile application over GSM networks. The system uses a PIC microcontroller connected to appliances via relays and optocouplers. An Android application is developed using Eclipse that sends encrypted control signals as SMS messages. Security involves password protection, user identification, and encrypted communications. The system was simulated in Proteus and allows monitoring and control of devices from a mobile phone.
Similar to 0 th review (20)
Eprojectprojectfinalreportgsmmonitoringcontrollingofdevicesusinggsm 090811012...
Eprojectprojectfinalreportgsmmonitoringcontrollingofdevicesusinggsm 090811012...
multiple input control by sms using GSM technology
multiple input control by sms using GSM technology
IRJET-A Comparative Study of use of the Library and the Internet as Sources o...
IRJET-A Comparative Study of use of the Library and the Internet as Sources o...
Bits pilani solar power fencing by blaze automation
Bits pilani solar power fencing by blaze automation
Advanced Automation System in Industrial Applications Using PIC Microcontrol...
Advanced Automation System in Industrial Applications Using PIC Microcontrol...
Multiuser sms based microcontroller wireless electronic board
Multiuser sms based microcontroller wireless electronic board
Iirdem implementation of smart homes and industrial automation system with se...
Iirdem implementation of smart homes and industrial automation system with se...
Recently uploaded
Artificial Intelligence for XMLDevelopment
In the rapidly evolving landscape of technologies, XML continues to play a vital role in structuring, storing, and transporting data across diverse systems. The recent advancements in artificial intelligence (AI) present new methodologies for enhancing XML development workflows, introducing efficiency, automation, and intelligent capabilities. This presentation will outline the scope and perspective of utilizing AI in XML development. The potential benefits and the possible pitfalls will be highlighted, providing a balanced view of the subject.
We will explore the capabilities of AI in understanding XML markup languages and autonomously creating structured XML content. Additionally, we will examine the capacity of AI to enrich plain text with appropriate XML markup. Practical examples and methodological guidelines will be provided to elucidate how AI can be effectively prompted to interpret and generate accurate XML markup.
Further emphasis will be placed on the role of AI in developing XSLT, or schemas such as XSD and Schematron. We will address the techniques and strategies adopted to create prompts for generating code, explaining code, or refactoring the code, and the results achieved.
The discussion will extend to how AI can be used to transform XML content. In particular, the focus will be on the use of AI XPath extension functions in XSLT, Schematron, Schematron Quick Fixes, or for XML content refactoring.
The presentation aims to deliver a comprehensive overview of AI usage in XML development, providing attendees with the necessary knowledge to make informed decisions. Whether you’re at the early stages of adopting AI or considering integrating it in advanced XML development, this presentation will cover all levels of expertise.
By highlighting the potential advantages and challenges of integrating AI with XML development tools and languages, the presentation seeks to inspire thoughtful conversation around the future of XML development. We’ll not only delve into the technical aspects of AI-powered XML development but also discuss practical implications and possible future directions.
20240605 QFM017 Machine Intelligence Reading List May 2024
Everything I found interesting about machines behaving intelligently during May 2024
GraphSummit Singapore | Graphing Success: Revolutionising Organisational Stru...
Sudheer Mechineni, Head of Application Frameworks, Standard Chartered Bank
Discover how Standard Chartered Bank harnessed the power of Neo4j to transform complex data access challenges into a dynamic, scalable graph database solution. This keynote will cover their journey from initial adoption to deploying a fully automated, enterprise-grade causal cluster, highlighting key strategies for modelling organisational changes and ensuring robust disaster recovery. Learn how these innovations have not only enhanced Standard Chartered Bank’s data infrastructure but also positioned them as pioneers in the banking sector’s adoption of graph technology.
AI 101: An Introduction to the Basics and Impact of Artificial Intelligence
Imagine a world where machines not only perform tasks but also learn, adapt, and make decisions. This is the promise of Artificial Intelligence (AI), a technology that's not just enhancing our lives but revolutionizing entire industries.
Best 20 SEO Techniques To Improve Website Visibility In SERP
Boost your website's visibility with proven SEO techniques! Our latest blog dives into essential strategies to enhance your online presence, increase traffic, and rank higher on search engines. From keyword optimization to quality content creation, learn how to make your site stand out in the crowded digital landscape. Discover actionable tips and expert insights to elevate your SEO game.
Infrastructure Challenges in Scaling RAG with Custom AI models
Building Retrieval-Augmented Generation (RAG) systems with open-source and custom AI models is a complex task. This talk explores the challenges in productionizing RAG systems, including retrieval performance, response synthesis, and evaluation. We’ll discuss how to leverage open-source models like text embeddings, language models, and custom fine-tuned models to enhance RAG performance. Additionally, we’ll cover how BentoML can help orchestrate and scale these AI components efficiently, ensuring seamless deployment and management of RAG systems in the cloud.
GraphSummit Singapore | Neo4j Product Vision & Roadmap - Q2 2024
Maruthi Prithivirajan, Head of ASEAN & IN Solution Architecture, Neo4j
Get an inside look at the latest Neo4j innovations that enable relationship-driven intelligence at scale. Learn more about the newest cloud integrations and product enhancements that make Neo4j an essential choice for developers building apps with interconnected data and generative AI.
TrustArc Webinar - 2024 Global Privacy Survey
How does your privacy program stack up against your peers? What challenges are privacy teams tackling and prioritizing in 2024?
In the fifth annual Global Privacy Benchmarks Survey, we asked over 1,800 global privacy professionals and business executives to share their perspectives on the current state of privacy inside and outside of their organizations. This year’s report focused on emerging areas of importance for privacy and compliance professionals, including considerations and implications of Artificial Intelligence (AI) technologies, building brand trust, and different approaches for achieving higher privacy competence scores.
See how organizational priorities and strategic approaches to data security and privacy are evolving around the globe.
This webinar will review:
- The top 10 privacy insights from the fifth annual Global Privacy Benchmarks Survey
- The top challenges for privacy leaders, practitioners, and organizations in 2024
- Key themes to consider in developing and maintaining your privacy program
Unlock the Future of Search with MongoDB Atlas_ Vector Search Unleashed.pdf
Discover how MongoDB Atlas and vector search technology can revolutionize your application's search capabilities. This comprehensive presentation covers:
* What is Vector Search?
* Importance and benefits of vector search
* Practical use cases across various industries
* Step-by-step implementation guide
* Live demos with code snippets
* Enhancing LLM capabilities with vector search
* Best practices and optimization strategies
Perfect for developers, AI enthusiasts, and tech leaders. Learn how to leverage MongoDB Atlas to deliver highly relevant, context-aware search results, transforming your data retrieval process. Stay ahead in tech innovation and maximize the potential of your applications.
#MongoDB #VectorSearch #AI #SemanticSearch #TechInnovation #DataScience #LLM #MachineLearning #SearchTechnology
Cosa hanno in comune un mattoncino Lego e la backdoor XZ?
ABSTRACT: A prima vista, un mattoncino Lego e la backdoor XZ potrebbero avere in comune il fatto di essere entrambi blocchi di costruzione, o dipendenze di progetti creativi e software. La realtà è che un mattoncino Lego e il caso della backdoor XZ hanno molto di più di tutto ciò in comune.
Partecipate alla presentazione per immergervi in una storia di interoperabilità, standard e formati aperti, per poi discutere del ruolo importante che i contributori hanno in una comunità open source sostenibile.
BIO: Sostenitrice del software libero e dei formati standard e aperti. È stata un membro attivo dei progetti Fedora e openSUSE e ha co-fondato l'Associazione LibreItalia dove è stata coinvolta in diversi eventi, migrazioni e formazione relativi a LibreOffice. In precedenza ha lavorato a migrazioni e corsi di formazione su LibreOffice per diverse amministrazioni pubbliche e privati. Da gennaio 2020 lavora in SUSE come Software Release Engineer per Uyuni e SUSE Manager e quando non segue la sua passione per i computer e per Geeko coltiva la sua curiosità per l'astronomia (da cui deriva il suo nickname deneb_alpha).
Programming Foundation Models with DSPy - Meetup Slides
Prompting language models is hard, while programming language models is easy. In this talk, I will discuss the state-of-the-art framework DSPy for programming foundation models with its powerful optimizers and runtime constraint system.
Removing Uninteresting Bytes in Software Fuzzing
Imagine a world where software fuzzing, the process of mutating bytes in test seeds to uncover hidden and erroneous program behaviors, becomes faster and more effective. A lot depends on the initial seeds, which can significantly dictate the trajectory of a fuzzing campaign, particularly in terms of how long it takes to uncover interesting behaviour in your code. We introduce DIAR, a technique designed to speedup fuzzing campaigns by pinpointing and eliminating those uninteresting bytes in the seeds. Picture this: instead of wasting valuable resources on meaningless mutations in large, bloated seeds, DIAR removes the unnecessary bytes, streamlining the entire process.
In this work, we equipped AFL, a popular fuzzer, with DIAR and examined two critical Linux libraries -- Libxml's xmllint, a tool for parsing xml documents, and Binutil's readelf, an essential debugging and security analysis command-line tool used to display detailed information about ELF (Executable and Linkable Format). Our preliminary results show that AFL+DIAR does not only discover new paths more quickly but also achieves higher coverage overall. This work thus showcases how starting with lean and optimized seeds can lead to faster, more comprehensive fuzzing campaigns -- and DIAR helps you find such seeds.
- These are slides of the talk given at IEEE International Conference on Software Testing Verification and Validation Workshop, ICSTW 2022.
HCL Notes and Domino License Cost Reduction in the World of DLAU
Webinar Recording: https://www.panagenda.com/webinars/hcl-notes-and-domino-license-cost-reduction-in-the-world-of-dlau/
The introduction of DLAU and the CCB & CCX licensing model caused quite a stir in the HCL community. As a Notes and Domino customer, you may have faced challenges with unexpected user counts and license costs. You probably have questions on how this new licensing approach works and how to benefit from it. Most importantly, you likely have budget constraints and want to save money where possible. Don’t worry, we can help with all of this!
We’ll show you how to fix common misconfigurations that cause higher-than-expected user counts, and how to identify accounts which you can deactivate to save money. There are also frequent patterns that can cause unnecessary cost, like using a person document instead of a mail-in for shared mailboxes. We’ll provide examples and solutions for those as well. And naturally we’ll explain the new licensing model.
Join HCL Ambassador Marc Thomas in this webinar with a special guest appearance from Franz Walder. It will give you the tools and know-how to stay on top of what is going on with Domino licensing. You will be able lower your cost through an optimized configuration and keep it low going forward.
These topics will be covered
- Reducing license cost by finding and fixing misconfigurations and superfluous accounts
- How do CCB and CCX licenses really work?
- Understanding the DLAU tool and how to best utilize it
- Tips for common problem areas, like team mailboxes, functional/test users, etc
- Practical examples and best practices to implement right away
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
The choice of an operating system plays a pivotal role in shaping our computing experience. For decades, Microsoft's Windows has dominated the market, offering a familiar and widely adopted platform for personal and professional use. However, as technological advancements continue to push the boundaries of innovation, alternative operating systems have emerged, challenging the status quo and offering users a fresh perspective on computing.
One such alternative that has garnered significant attention and acclaim is Nitrux Linux 3.5.0, a sleek, powerful, and user-friendly Linux distribution that promises to redefine the way we interact with our devices. With its focus on performance, security, and customization, Nitrux Linux presents a compelling case for those seeking to break free from the constraints of proprietary software and embrace the freedom and flexibility of open-source computing.
Uni Systems Copilot event_05062024_C.Vlachos.pdf
Unlocking Productivity: Leveraging the Potential of Copilot in Microsoft 365, a presentation by Christoforos Vlachos, Senior Solutions Manager – Modern Workplace, Uni Systems
UiPath Test Automation using UiPath Test Suite series, part 6
Welcome to UiPath Test Automation using UiPath Test Suite series part 6. In this session, we will cover Test Automation with generative AI and Open AI.
UiPath Test Automation with generative AI and Open AI webinar offers an in-depth exploration of leveraging cutting-edge technologies for test automation within the UiPath platform. Attendees will delve into the integration of generative AI, a test automation solution, with Open AI advanced natural language processing capabilities.
Throughout the session, participants will discover how this synergy empowers testers to automate repetitive tasks, enhance testing accuracy, and expedite the software testing life cycle. Topics covered include the seamless integration process, practical use cases, and the benefits of harnessing AI-driven automation for UiPath testing initiatives. By attending this webinar, testers, and automation professionals can gain valuable insights into harnessing the power of AI to optimize their test automation workflows within the UiPath ecosystem, ultimately driving efficiency and quality in software development processes.
What will you get from this session?
1. Insights into integrating generative AI.
2. Understanding how this integration enhances test automation within the UiPath platform
3. Practical demonstrations
4. Exploration of real-world use cases illustrating the benefits of AI-driven test automation for UiPath
Topics covered:
What is generative AI
Test Automation with generative AI and Open AI.
UiPath integration with generative AI
Speaker:
Deepak Rai, Automation Practice Lead, Boundaryless Group and UiPath MVP
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...Edge AI and Vision Alliance
For the full video of this presentation, please visit: https://www.edge-ai-vision.com/2024/06/building-and-scaling-ai-applications-with-the-nx-ai-manager-a-presentation-from-network-optix/
Robin van Emden, Senior Director of Data Science at Network Optix, presents the “Building and Scaling AI Applications with the Nx AI Manager,” tutorial at the May 2024 Embedded Vision Summit.
In this presentation, van Emden covers the basics of scaling edge AI solutions using the Nx tool kit. He emphasizes the process of developing AI models and deploying them globally. He also showcases the conversion of AI models and the creation of effective edge AI pipelines, with a focus on pre-processing, model conversion, selecting the appropriate inference engine for the target hardware and post-processing.
van Emden shows how Nx can simplify the developer’s life and facilitate a rapid transition from concept to production-ready applications.He provides valuable insights into developing scalable and efficient edge AI solutions, with a strong focus on practical implementation.HCL Notes und Domino Lizenzkostenreduzierung in der Welt von DLAU
Webinar Recording: https://www.panagenda.com/webinars/hcl-notes-und-domino-lizenzkostenreduzierung-in-der-welt-von-dlau/
DLAU und die Lizenzen nach dem CCB- und CCX-Modell sind für viele in der HCL-Community seit letztem Jahr ein heißes Thema. Als Notes- oder Domino-Kunde haben Sie vielleicht mit unerwartet hohen Benutzerzahlen und Lizenzgebühren zu kämpfen. Sie fragen sich vielleicht, wie diese neue Art der Lizenzierung funktioniert und welchen Nutzen sie Ihnen bringt. Vor allem wollen Sie sicherlich Ihr Budget einhalten und Kosten sparen, wo immer möglich. Das verstehen wir und wir möchten Ihnen dabei helfen!
Wir erklären Ihnen, wie Sie häufige Konfigurationsprobleme lösen können, die dazu führen können, dass mehr Benutzer gezählt werden als nötig, und wie Sie überflüssige oder ungenutzte Konten identifizieren und entfernen können, um Geld zu sparen. Es gibt auch einige Ansätze, die zu unnötigen Ausgaben führen können, z. B. wenn ein Personendokument anstelle eines Mail-Ins für geteilte Mailboxen verwendet wird. Wir zeigen Ihnen solche Fälle und deren Lösungen. Und natürlich erklären wir Ihnen das neue Lizenzmodell.
Nehmen Sie an diesem Webinar teil, bei dem HCL-Ambassador Marc Thomas und Gastredner Franz Walder Ihnen diese neue Welt näherbringen. Es vermittelt Ihnen die Tools und das Know-how, um den Überblick zu bewahren. Sie werden in der Lage sein, Ihre Kosten durch eine optimierte Domino-Konfiguration zu reduzieren und auch in Zukunft gering zu halten.
Diese Themen werden behandelt
- Reduzierung der Lizenzkosten durch Auffinden und Beheben von Fehlkonfigurationen und überflüssigen Konten
- Wie funktionieren CCB- und CCX-Lizenzen wirklich?
- Verstehen des DLAU-Tools und wie man es am besten nutzt
- Tipps für häufige Problembereiche, wie z. B. Team-Postfächer, Funktions-/Testbenutzer usw.
- Praxisbeispiele und Best Practices zum sofortigen Umsetzen
Recently uploaded (20)
20240605 QFM017 Machine Intelligence Reading List May 2024
20240605 QFM017 Machine Intelligence Reading List May 2024
GraphSummit Singapore | Graphing Success: Revolutionising Organisational Stru...
GraphSummit Singapore | Graphing Success: Revolutionising Organisational Stru...
AI 101: An Introduction to the Basics and Impact of Artificial Intelligence
AI 101: An Introduction to the Basics and Impact of Artificial Intelligence
Best 20 SEO Techniques To Improve Website Visibility In SERP
Best 20 SEO Techniques To Improve Website Visibility In SERP
Infrastructure Challenges in Scaling RAG with Custom AI models
Infrastructure Challenges in Scaling RAG with Custom AI models
GraphSummit Singapore | Neo4j Product Vision & Roadmap - Q2 2024
GraphSummit Singapore | Neo4j Product Vision & Roadmap - Q2 2024
Unlock the Future of Search with MongoDB Atlas_ Vector Search Unleashed.pdf
Unlock the Future of Search with MongoDB Atlas_ Vector Search Unleashed.pdf
Cosa hanno in comune un mattoncino Lego e la backdoor XZ?
Cosa hanno in comune un mattoncino Lego e la backdoor XZ?
Programming Foundation Models with DSPy - Meetup Slides
Programming Foundation Models with DSPy - Meetup Slides
HCL Notes and Domino License Cost Reduction in the World of DLAU
HCL Notes and Domino License Cost Reduction in the World of DLAU
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
UiPath Test Automation using UiPath Test Suite series, part 6
UiPath Test Automation using UiPath Test Suite series, part 6
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
HCL Notes und Domino Lizenzkostenreduzierung in der Welt von DLAU
HCL Notes und Domino Lizenzkostenreduzierung in der Welt von DLAU
0 th review
- 1. SECURED ACCESSING OF POWER WINDOW BY REMOTE Project Guidance: Revathi.T TIFAC Core PRESENTED BY: SAI BHARATHI.G(11MEA0023) NAGA PRADEEP.V(11MEA0039) TIFAC CORE VIT UNIVERSITY
- 2. INTRODUCTION • Today, many cars with power window locks have a radio frequency remote keyless system, which allows a person to press a button on a remote control key fob. • The problem occurs when the driver comes out the car without realizing the key inside it is very difficult to take out the keys as the all the doors and windows will be locked automatically. So in order to overcome this situation a solution is proposed here. TIFAC CORE VIT UNIVERSITY
- 3. OBJECTIVE • To design and develop a system which allows to access the power window of car remotely. TIFAC CORE VIT UNIVERSITY
- 4. METHODOLOGY • A command will be sent from the mobile, and it will be received using GSM modem present in the vehicle. • In order to protect the vehicle from malfunctioning of other people instead of authorized person, second level of security coding is used. • Depending upon the command received from authorised person, the accessing of power window can be done which will be connected by a LIN network. TIFAC CORE VIT UNIVERSITY
- 5. BLOCK DIAGRAM SCI GSM MOBILE LIN SLAVE MODEM LIN MASTER POWER WINDOW RELAY CIRCUIT TIFAC CORE VIT UNIVERSITY
- 6. Hard wares Used DEMO9S12XDT512 The HCS 12 contains two SCI module. SCI is operated by two control registers: SCI0CR1 (SCI1CR1) and SCI0CR2 (SCI1CR2). GSM modem communicates to HCS 12 by using serial communication registers. GSM MODEM visiontek 81GC is a highly flexible GSM modem for easy integration. It is perfect solution for to use with GSM gateway. TIFAC CORE VIT UNIVERSITY
- 7. TIFAC CORE VIT UNIVERSITY
- 8. GSM MODEM COMMAND USED:- AT The communication always starts with AT command. AT refers to ATtention AT+CMGF=“1” In this we are having two formats, text mode and PDU mode. By enabling the text mode can be selected. TIFAC CORE VIT UNIVERSITY
- 9. Phase 1: Communicating with GSM Phase2: Master and Slave communication Phase3: Operating motor with relay circuit TIFAC CORE VIT UNIVERSITY
- 10. THANK YOU TIFAC CORE VIT UNIVERSITY