College Call Girls Nashik Nehal 7001305949 Independent Escort Service Nashik
ppt on spv module and emt
1. A
Presentation
On
Solar Photo Voltaic Modules
&
Electronic Milk Tester
At
Rajasthan Electronics & Instruments Limited
(Kanakpura , Jaipur)
Submitted by
Pradeep Kumar kumawat
31-8-2015 1
2. Contents
Introduction about REIL
Solar Photo Voltaic Module
(i) Working Principle
(ii) Block Diagram
(iii) Manufacturing Process of SPV Module
(iv) Advantages & Disadvantages
Electronics Milk Tester
(i) Working Principle
(ii) Features of EMT
Conclusion
31-8-2015 2
3. Introduction About REIL
REIL was established in 1981.
It has an important place among the Electronic Industry Of
Rajasthan.
It is a Public Sector Unit.
It is a joint venture between Gov. of India And Gov. of
Rajasthan.
Shareholding Pattern
1) Gov. of India 51% Holding
2) Gov. of Rajasthan 49% Holding
31-8-2015 3
4. Solar Photo Voltaic Module
SPV module is used to convert sun light into electrical energy.
It has connected assembly of solar cells.
Cells are made up of silicon.
Output Of each cell is approximately 0.5 volt dc.
SPV Module
31-8-2015 4
7. Manufacturing Process Of SPV Module
Tabbing Of Cells
Row Making
Stringing
Lay- Up
Lamination
Curing
Trimming
Channeling
31-8-2015 7
8. 1. Tabbing of cells
Process of making terminals of a Bare cell by soldering copper
strips to the Bus bar.
31-8-2015 8
9. 2. Row making
A row of cells is made by connecting positive surfaces of one
cell to the negative surface of another cell.
31-8-2015 9
10. 3. Stringing
The rows of SPV cells are connected in series to get desired
power rating.
31-8-2015 10
11. 4. Lay-Up
It is a process of placing laminating material to the either side
of the string. The laminating materials are-
(i) Top Glass (Toughened Glass)
(ii) Ethylene Vinyl Acetate sheet
(iii) Polyester Taddler
5. Lamination
The SPV module after lay-up process is placed in the
laminator for 11 minutes.
31-8-2015 11
12. 6.Curing
In this process the laminating material attain full strength by
placing the module into 1200c temperature for 20 minutes.
7.Trimming
The final module is obtained by cutting the extra laminating
material.
31-8-2015 12
13. 8.Channeling
Modules are channelled from all the four sides.
Anodized aluminium frames are used for channelling.
Channels prevent any damage to the module.
31-8-2015 13
14. Advantages
It have no moving parts.
No noise pollution or any othe type of pollution.
Requires minimum maintenance.
Have long service lifetimes (upto 20 years).
31-8-2015 14
16. Electronic Milk Tester
It is an instrument which is used for the measurement of fat
percentage in milk.
31-8-2015 16
17. Working Principle
It works on the photometric measurement of light scattered by
the fat globules present in the milk sample.
31-8-2015 17
18. Features of EMT
Operate on AC mains as well as battery.
Performs 110-130 samples per hour.
Instant measurement and display of milk fat.
Instant calculation of amount payable.
Printing facility.
31-8-2015 18
19. Conclusion
This training made me learn the practical aspects of
engineering.It gave me experience of working in a professional
environment with professional people at a professional place. I
have learnt adjusting myself to the busy schedule and workload
which I will have to face in the future.
31-8-2015 19