2. 12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
2
*Petrophysics is the study of rock properties and their
interactions with fluids (gases, liquid hydrocarbons, and aqueous
solutions)
*The petrophysicist is the link between the subsurface disciplines
*Petrophysics is the science that integrates many valuable data
together to have quantitative formation evaluation based on
conventional/advanced logs and core analyses
*Log analysis vs. petrophysics
3. Log Analysis
Different Inputs CertainOutputs
GR Resistivity Porosity ษธ
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
3
๐#๐%&
6. Is it Complicated?!! J
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
6
*A 24/7 job
*Presence of hydrocarbon is your call
*Wells/lithology could be very complicated
*Tough to learn in most companies
*Skill shortage in the industry
*Too much to learn
*What to start with?
*Where/How to start?
โฆ........BUT, is it worth really?
7. A Shed of Light...
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
7
*Everyone takes the petrophysicist outputs to use
*You are the link between the geologist and the RE
*You learn how to manage, work under stress and how to provide
only what is accepted
*You manage the LWD and wireline operations
*You are dealing with data no one literally see or use
*You are dealing with new technology, that makes you always
think
*Your output is seen at all management levels
10. What To Do (Simply)?
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
10
*Estimate clay volume
*Calculate the porosity
*Read the resistivity
*Calculate water saturation
REMEMBER!!
The key for log interpretation is to understand how to read the log
11. How to Read the Log?
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
11
This log is drawn by hand for presentation purposes only
12. Clay Volume Calculation
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
12
*A simple equation using GR log is used to evaluate the clay
volume
*The neutron/density could be used to calculate the clay volume
with the same equation
*The softwares use different evaluation appraoches, a bit
complicated, depending on the inputs used
*Porosity tools or even resistivity could be used to evaluate the
clay volume
๐ฎ๐น ๐ฅ๐จ๐ , ๐ฎ๐น ๐๐
๐ฎ๐น ๐๐ ,๐ฎ๐น ๐๐
=shV
13. Density Porosity Calculation
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
13
* The density log is the most robust porosity tool
* The porosity is calculated using simple equation:
โ ๐ซ =
๐ ๐๐ โ ๐๐๐๐
๐ ๐๐ โ ๐ ๐๐
* Matrix density differs by lithology
* L.ST: 2.71 g/cc
* S.ST: 2.65 g/cc
* Dol.: 2.847 g/cc
* The ๐ ๐๐ is the density of the fluid saturating the rock immediately surrounding the
BH, (usually mud filtrate)....SLB
* The tool is affected by washouts, rugose holes and high tension
14. Density Porosity Chart
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
14
27 p.u.
*Determine the porosity from the density log value of 2.4 g/cc for
a dolomite reservoir?
15. Sonic Porosity Calculation
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
15
* The sonic log is the reflecting primary porosity only
* The porosity is calculated using simple equation:
* Matrix density differs by lithology
*S.ST: 55.5-51.3 ยตs/ft (18000-19500 ft/s)
*L.ST: 47.6-43.5 ยตs/ft (21000-23000 ft/s)
*Dol.: 43.5-38.5 ยตs/ft (23000-26000 ft/s)
* The tool is used for seismic tie, CMT job evaluation and secondary porosity
evaluation
โ < =
โ>?@A,โ>BC
โ>D?,โ>BC
16. Sonic Porosity Chart
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
16
10.5 p.u.
*Determine the porosity from the sonic log value of 70 ยตs/ft for a
sandstone reservoir?
34 p.u.
17. Calculating Total Porosity
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
17
* With 3 inputs, the porosity could be the average of them
* For Gas Intervals
ฯFGฯ<GฯH
I
= Tฯ
ฯT =
FLMNOGHLMNO
P
20. Water Resistivity (Rw)
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
20
* This is a key parameter in saturation calculation
* Rw is evaluated through different methods:
* Reversed Archie Method
* Pickett Plot
* Formation Water Salinity
* The uncertainty in the Rw value affects the saturation profile
near the contact dramatically
This log is drawn by hand for presentation purposes only
21. Rw From Pickett Plot
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
21
*Pickett plot is very important tool
to detect the water resistivity
*It should be used as a
confirmation for the reversed
Archie method with more
accuracy
*The m value is the slope of the
line
*(m) value is crucial in carbonates
*The core data is usually needed to
vary (m) parameter, otherwise the
default value is used
22. Salinity Value From Slb Chart
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
22
*Easily used to detect the
Rw and salinity using the
formation temperature
*The salinity should not
change across different
locations/wells in the same
structure
*The Rw changes with
temperature/depth
*The formation salinity could
vary significantly from
formation to another
23. Calculating Water Saturation
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
23
*There are several models for Sw calculations
*Two main reservoirs exist; clean and shaly reservoirs
*The clean formations are evaluated with Archie equation
*Shaly reservoirs use different models depend on the clay
distribution
*Schlumberger/Laminated sand-shale simplified model is one
simple model to evaluate the shaly sands
1
๐ a
=
โ P
๐๐คP
1 โ ๐cde โ ๐๐ ๐ค
+
๐cde
๐ %&
๐ โ๐น๐
ะค ๐
โ
๐น๐
=n)W(S
25. The Effective Porosity (Oil)
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
25
*In oil bearing reservoirs, the
effective porosity curve is
divided into three curves, the
bulk volume of water (BVW),
movable oil and residual oil.
Residual Oil
Movable Oil
Bulk Volume Water
0.5 0effะค
26. The Effective Porosity (Gas)
12/08/2016
Abdelrahman Elkhateeb
www.facebook.com/formation.evaluation
26
*In gas bearing reservoirs, the
effective porosity curve is
divided into three curves, the
bulk volume of water, the
movable fluids and the gas.
0.5 0effะค
Residual Gas
Movable Hydrocarbon
Bulk Volume Water