VIP Call Girls Service Kondapur Hyderabad Call +91-8250192130
Rajesh demonstration plan
1. DEMONSTRATION PLAN
Trade : - Electrician Unit :-
Date : - Time :-
Demo No :-
PREPARATION :-
SKILL :- GODOWN WIRING ON CONDUIT PIPE.
(1). Objective : (After demonstrating of the skill the trainees will be able to)
(a). Identify the all wiring Accessories and material.
(b). Draw the lay-out of Godown wiring.
(c). Connection and fitting all materials.
(d). Operation and take the table chartof godown wiring.
(2). Tools & other requirements :-
(1). Combination plier . 150 mm. 01.
(2). Screw driver. 150 mm. 01.
(3). Neon tester. 0 – 500 volt AC 01.
(4). Electrician knife. 01.
(5). Hacksaw framewith blade. 300 mm. 01.
(6). Hammer. 500 gram. 01.
(7). Pocker. 150 mm. 01.
(8). Hand drill machine with drill bit. 01.
(9). WIREstriper . 01.
2. Materials : -
PVC conduit pipe (12 fits), PVC Copper wire (1.5 sq mm ),
S.P. switch (5 amps 250 volts 01 nos.), Two way switch
(5 amps 250 volts 01 nos.), DPSTswitch(10 amps 250volts 01 N),
Fuse, Bulb (03 Nos.), Junction box, Bend Lbo, Saddle and srew .
(3). Introduction :-
(a) Review :- Stare casewiring on conduit pipe.
(b). Motivation:- When we are working in a workshop and need a
Light to go the different place, there is also a need
To off and on, whatto do for it.
PRESENTATION :-
Procedure Information point Hints
AT FIRSTSTEP OF
WORKING.
CIRCUIT
DIAGRAM.
ARRANGEMENT
OF WIRING
MATERIALS.
Collect all the tools and
materials and put on the
bench wherethe work place is
to be done.
Firstprepare and check lay -
out of the circuit.
Now make this diagram on
wiring board.
Use materials according to
diagram and fitting diagram.
To careful putting
materials on
table.
Careful making
the circuit
diagram.
Chart.
3. CONNECTION.
CHECKING OF
WIRING FITTING
AND TESTING
WITH MAGGER.
OPERATION
AND TAKE NOTE
DOWN THAN
STOP.
PRECAUTION.
Now wiring connection the wire
every where.
Now fitting all materials like Bulbs,
switch, Holders.
After fitting, test all connection to
check from testing lamp and
Magger.
Now check the all Bulbs by lighting
them one by one.
Turn on the main switch and one
by one operation and take the
table chart.
Operation is complete than remove
all material.
All wireconnected tight and right.
Testing the wiring with Magger
careful.
All connection
should be tight
and right.
Testing careful.
Remove to
careful.
SAFETY.
0= OFF. NG.
1= ON. G.
TABLE CHART :-
SR. SP1 TW1 TW2 TW3 L1 L2 L3 L4 OFF
01 1 1 1 0 1 0 0 0 0
02 1 1 1 1 0 1 0 0 0
03 1 0 1 1 0 0 1 0 0
04 1 0 0 1 0 0 0 1 0
4. APPLICATION :-
(a). Where is use of godown wiring ?
(b). What is useof wire sizeof godown wiring ?
(c). What is advantageof godown wiring?
SUMMARY :-
Make the circuit diagram of godown wiring make materials and
Fitting , connection , operation.
TEST :-
(a). What is distance between two saddle ?
(b). What is switch rating ?
(c). What is use of poker and drill machine ?
ASSIGNMENT :-
Make the godown wiring circuit diagram and which use of
godown wiring.
REFERENCE :-
Electrical practical (Priti Agrawal).
NEXT SKILL :-
Earth testing.