Upcoming SlideShare
×

# Experimentdsd[1]

7,718 views

Published on

1 Like
Statistics
Notes
• Full Name
Comment goes here.

Are you sure you want to Yes No
• Be the first to comment

Views
Total views
7,718
On SlideShare
0
From Embeds
0
Number of Embeds
6
Actions
Shares
0
43
0
Likes
1
Embeds 0
No embeds

No notes for slide

### Experimentdsd[1]

1. 1. EXPERIMENT NO. 1AIM:- Verification of basic gatesCOMPONENTS:- 5 v power supply, Bread board, connecting wires, LED(1), IC7404, 7408, 7432, 7486, 74266, 7400, 7402IC DIAGRAM & TRUTH TABLE:- BASIC GATESIC7404 (NOT GATE)i/p o/pA Y0 11 0IC7432 (OR GATE) Y=i/p o/pA B Y0 0 00 1 11 0 11 1 1IC7408(AND GATE) Y=i/p o/pA B Y0 0 00 1 01 0 01 1 1
2. 2. DERIVED GATESIC7486(EX-OR GATE) Y=i/p o/pA B Y0 0 00 1 11 0 11 1 0IC74266(EX-NOR GATE) Y=i/p o/pA B Y0 0 10 1 01 0 01 1 1UNIVERSAL GATESIC7400(NAND GATE) Y=i/p o/pA B Y0 0 10 1 11 0 11 1 0
3. 3. IC7402(NOR GATE) Y=i/p o/pA B Y0 0 10 1 01 0 01 1 0THEORY:- In digital system there are only few basic operations performed, irrespective of thecomplexity of the system . These operations may be required to be performed number of times in alarge digital system like digital computer or digital control systems, etc. The basic operations are AND,OR, NOT, NAND, NOR, EX-OR, EX-NOR. The circuits which perform these operations are called asGATEs. These GATEs are basic building blocks for any digital circuit.PROCEDURE:-1) Connect the IC on the bread board. 2) Connect pin no. 7 to ground and pin no. 14 to vcc (5v supply). 3) Connect the LED to the o/p pin of a gate. 4) give the i/p to the i/p pins of the same gate 5) Verify the o/p with respect to the i/p.RESULT:-CONCLUSION:-PRECAUTIONS:- 1) Power supply should not exceeds than 5v. 2) Connections should be tight. 3) Components should be tested before performing the practical.
4. 4. EXPERIMENT NO. 2AIM:- Study of full adder , full substractor and BCD adderCOMPONENTS:- IC 7486, IC7408, IC 7432, IC7404, IC 7410, IC7400, IC7483(2), LED(6), Register(6)470Ω, Bread board, power supply, connecting wires.DIAGRAM & TRUTH TABLE:-Full AdderA B Cin S Co0 0 0 0 00 0 1 1 00 1 0 1 00 1 1 0 11 0 0 1 01 0 1 0 11 1 0 0 11 1 1 1 1Full SubstractorA B Cin D B0 0 0 0 00 0 1 1 10 1 0 1 10 1 1 0 11 0 0 1 01 0 1 0 01 1 0 0 01 1 1 1 1
5. 5. BCD AdderTHEORY:-PROCADURE:-1) Mount the ICs on the bread board. 2) Do the connections for Full adder, substractor, BCD adder. 3) Apply 5v supply to pin 14 of each IC and connect pin 7 of each IC to ground. 4) Check the o/p on LED’s and verify the truth table for each ckt.RESULT:-CONCLUSION:-PRECAUTIONS:- 1) Power supply should not exceeds than 5v. 2) Connections should be tight. 3) Components should be tested before performing the practical.
6. 6. EXPERIMENT NO. 3AIM:- Implementation of Parity checker using gates.COMPONENTS:- IC7486, LED, register, bread board, connecting wires power supply.DIAGRAM & TRUTH TABLE:-input o/pP B2 B1 B0 PEO0 0 0 0 10 0 0 1 00 0 1 0 00 0 1 1 10 1 0 0 00 1 0 1 10 1 1 0 10 1 1 1 01 0 0 0 01 0 0 1 11 0 1 0 11 0 1 1 01 1 0 0 11 1 0 1 01 1 1 0 01 1 1 1 1THEORY:-PROCEDURE:- 1) Do the connections as per the ckt. Diagram. 2) Give asset of i/p to the ckt. 3) Check the error o/p. 4) Verify the truth table for ODD parity.RESULT:-CONCLUSION:-PRECAUTIONS:- 1) Power supply should not exceeds than 5v. 2) Connections should be tight. 3) Components should be tested before performing the practical.
7. 7. EXPERIMENT NO. 4AIM:- Implementation of Boolean expression using MUX IC 74153. Y=COMPONENTS:- IC74153, LED, 470Ω register,IC7432, bread board , connecting wires, etc.DIAGRAM & TRUTH TABLE:-input o/pS3 S2 S1 Y0 0 0 10 0 1 00 1 0 10 1 1 01 0 0 11 0 1 01 1 0 11 1 1 0THEORY:-PROCEDURE:- 1) Mount the IC on the bread board. 2) Do the connections as given in the ckt. Diagram. 3) Connect pin no. 8 of IC74153 to ground and pin no. 16 to Vcc. 4) Connect pin no. 7 of IC 7432& IC7404 to ground and pin no. 14 to Vcc. 5) Give the i/p and verify the o/p .RESULT:-CONCLUSION:- PRECAUTIONS:- 1) Power supply should not exceeds than 5v. 2) Connections should be tight. 3) Components should be tested before performing the practical.
8. 8. EXPERIMENT NO. 5AIM:- Implement the following function using 4:16 line decoder. F 1= F 1=COMPONENTS:- IC 74154, 2LED , 2 register 470Ω, 2 IC7432, 2 IC7404, bread board connecting wires.DIAGRAM:-input o/pA B C D F1 F20 0 0 0 1 00 0 0 1 1 00 0 1 0 1 00 0 1 1 1 00 1 0 0 0 00 1 0 1 0 00 1 1 0 0 00 1 1 1 0 01 0 0 0 0 01 0 0 1 0 01 0 1 0 0 01 0 1 1 0 01 1 0 0 0 11 1 0 1 0 11 1 1 0 0 11 1 1 1 0 1THEORY:-PROCEDURE:- 1) Mount the IC on the bread board. Do the connections as given in the ckt. Diagram 2) Connect pin no. 12 of IC74154 to ground and pin no. 24 to Vcc. 3) Connect pin no. 7 of IC 7432 & IC7404 to ground and pin no. 14 to Vcc. 4) Give the i/p and verify the o/p .RESULT:-CONCLUSION:-PRECAUTIONS:- 1) Power supply should not exceeds than 5v. 2) Connections should be tight. 3) Components should be tested before performing the practical.
9. 9. EXPERIMENT NO. 6AIM:- Conversion of Flip-flop.COMPONENTS:- 2(IC7400) ,(IC7410),bread board,2 registers, connecting wires,2 LED’s,power supply.DIAGRAM :-D FF from SR FFINPUTS OUTPUTS COMMENTE D QN+1 QN+10 X QN QN NC1 0 0 1 RESET1 1 1 0 SETJK FF from T FFINPUTS OUTPUTS COMMENTE T QN+1 QN+10 X QN QN NC1 0 QN QN NC1 1 QN QN TOGGLETHEORY:-PROCEDURE:-1) Connect the circuit as given in the diagram. 2) Apply the inputs and clock input to the circuit. 3) Connect the LED to the o/p pin of a gate. 5) Verify the o/p on LEDs and verify the truth table given.RESULT:-
10. 10. EXPERIMENT NO. 7AIM:- Design decade counter using IC7490.COMPONENTS:- IC7490, bread board, connecting wires , LED’s 4, power supply.DIAGRAM & TRUTH TABLE:-CLK OA OB OC OD0 0 0 0 01 0 0 0 12 0 0 1 03 0 0 1 14 0 1 0 05 0 1 0 16 0 1 1 07 0 1 1 18 1 0 0 09 1 0 0 110 1 0 1 011 1 0 1 1THEORY:-PROCEDURE:- 1) Mount the IC 7490 on the bread board. 2) Do the connections as given in the diagram. 3) Check the sequence generated by counter & verify the truth table.RESULT:-CONCLUSION:-PRECAUTIONS:- 1) Power supply should not exceeds than 5v. 2) Connections should be tight. 3) Components should be tested before performing the practical.
11. 11. EXPERIMENT NO. 8AIM:- Study of universal shift register IC7495.COMPONENTS:- IC7495, bread board, connecting wires, 4 LED’s, power supply.DIAGRAM:-Pin diagramPin Function1 Serial i/p2,3,4,5 Parallel i/p6 Mode control8 Clock for left shift & load9 Clock for right shift10,11, o/p’s12,13Parallel loadingSerial shift right Serial shift left
12. 12. THEORY:-PROCEDURE:- 1) Connect the IC 7495 on the bread board. 2) Give clock from function generator. 3) Do the connections for the register in different modes one by one and check the o/p on LED’s.RESULT:-CONCLUSION:-PRECAUTIONS:- 1) Power supply should not exceeds than 5v. 2) Connections should be tight. 3) Components should be tested before performing the practical.CONCLUSION:-PRECAUTIONS:- 1) Power supply should not exceeds than 5v. 2) Connections should be tight. 3) Components should be tested before performing the practical.
13. 13. ATHARVA COLLEGE OF ENGG. DEPARTMENT OF ELECTRONICS ENGG. SUB:- DIGITAL SYSTEM DESIGN LIST OF EXPERIMENT1) Verification of basic gates2) Study of full adder , full substractor and BCD adder3) Implementation of Parity checker using gates.4) Implementation of Boolean expression using MUX IC 74153. Y=5) Implement the following function using 4:16 line decoder. F1=6) Convert SR FF into JK, D and T FF7) Design decade counter using IC7490.8) Study of universal shift register IC7495. Mr.zafar khan (Subject in charge DSD-1)