Successfully reported this slideshow.
We use your LinkedIn profile and activity data to personalize ads and to show you more relevant ads. You can change your ad preferences anytime.

Report index part1

report format

  • Be the first to comment

Report index part1

  1. 1. i | P a g e THE SEMINAR REPORT ON TOPIC “Fabrication and testing of Baltimore truss made up of Bamboo” SUBMITTED TO MIT ACADEMY OF ENGINEERING, ALANDI(D) PUNE SUBMITTED BY 1) Omkar Rane SETB118 2) Sandhya Awari SETB116 3) Nikhil Khandelwal SETB103 4) Dipak Chaudhari SETB105 5) Rajavardhan Rishi SETB137 6) Pranav Waghmare SETB123 Course - Civil Prototyping Course Code- ET 206 Course Faculty Dr. Joshi Amrut Anant 2017-2018 DEPARTMENT OF CIVIL ENGINEERING
  2. 2. Civil Prototyping MIT Academy of Engineering ii | P a g e MIT ACADEMY OF ENGINEERING ALANDI (D) PUNE An Autonomous Institute CERTIFICATE This is to certify that the Credit seminar report entitled “Fabrication and testing of Pratt truss bridge made up of bamboo submitted by Omkar Rane SETB118 Sandhya Awari SETB116 Nikhil Khandelwal SETB103 Dipak Chaudhari SETB105 Rajavardhan Rishi SETB137 Pranav Waghmare SETB123 , of Electronics and Telecommunication Engineering of MIT Academy of Engineering is record of his own work carried out under my supervision and guidance. The matter enclosed here is not been submitted elsewhere for award of Bachelor of Technology degree. Internal Examiner External examiner
  3. 3. Civil Prototyping MIT Academy of Engineering iii | P a g e ACKNOWLEDGEMENT I would like to express my sincere thanks and gratitude to professor Dr. Amrut Joshi Sir for his continuous and unfailing support, guidance and help, which have been invaluable during the course of this project. His knowledge, insight and constant motivation at each step of the project has been instrumental in its completion. I would like to take this opportunity to thank the entire staff at Structures Laboratory and the Civil Engineering Laboratory for their cooperation and assistance in the lab-work that was required for this project.
  4. 4. Civil Prototyping MIT Academy of Engineering iv | P a g e ABSTRACT The main objective of this project was to design bridge type structures using bamboo, and arrive at the optimum design. For the structure, the design of base plate, inclined and top members, and joints of the structure have been carried out. For the design of joints, the experimental testing of bamboo joints has been carried out in the compression Testing Machine in the civil engineering Laboratory. The manual analysis of the forces and moments has been carried out. fabrication of the truss has been done by the completion of pretest analysis of bamboo joints. The design details have been depicted with figures and labelled. Using compression testing machine, a test has been carried out at a bridge truss. it holds a maximum compressive strength of 5.3 KN, and then it breaks down.
  5. 5. Civil Prototyping MIT Academy of Engineering v | P a g e Table of Content TOPICS PAGE NO. Certificate i Acknowledgement iii Abstract iv List of Table vi List Of figure vii CHAPTER 1: Introduction 1 CHAPTER 2: Planning of Trussed Bridge 4 CHAPTER 3: Pre-Test Analysis 6 CHAPTER 4: Compression, Tension And Joint Test 9 CHAPTER 5: Fabrication Of Baltimore Truss Bridge 13 CHAPTER 6: Test Preparation, Test, Results And Discussing 15 CHAPTER 7: Conclusions 17 Reference 18
  6. 6. Civil Prototyping MIT Academy of Engineering vi | P a g e LIST OF TABLES Content of Table Table Number Direct and Indirect cost 2.1 Labor cost 2.2 Transportation cost 2.3 Machine and tools hiring cost 2.4 Electricity cost based on machine usage. 2.5 Material cost analysis 2.6 Force analysis on each member 3.1 Type of forces 3.2 Dimensions of members 3.3 Compression test observations 4.1 Tensile testing observations 4.2 Joints testing observations 4.3
  7. 7. Civil Prototyping MIT Academy of Engineering vii | P a g e LIST OF FIGURES Content Figure Number Baltimore truss 1.1 Tension and compression members of Baltimore truss 1.2 Schematic diagram of Baltimore truss 1.3 Tools used while making truss 2.1 Resolution of forces on truss members. 3.1 Schematic diagram of Baltimore truss. 3.2 Specimen of various sizes for testing. 4.1 Specimen testing under compression. 4.2 Specimen testing under bending condition. 4.3 Specimen testing under tensile conditions. 4.4 Tri axial machine setup. 4.5 Fish mouth bolted joints. 5.1 Bevel cut bolted joints. 5.2 Fabrication of Baltimore single panel. 5.3 Baltimore truss bridge fabrication 5.4 Testing truss for verifying failure prediction analysis. 6.1
  8. 8. Civil Prototyping MIT Academy of Engineering viii | P a g e

    Be the first to comment

    Login to see the comments

  • UmashreeHaranal

    Feb. 17, 2019

report format

Views

Total views

1,128

On Slideshare

0

From embeds

0

Number of embeds

0

Actions

Downloads

6

Shares

0

Comments

0

Likes

1

×