It is an automated sidestand which is designed for two wheelers

1. AUTOMATIC SIDE STAND
1
By
Jisin Jijo

2. 1.
2.
3.
4.
5.
6.
7.
8.
9.
Contents
Introduction
Problem Definition
Innovation Proposed
Literature Review
Methodology
Working Mechanism
Components and Specifications
Project Progress
References
2

3. 1.Introduction
⮚ One of the issues of motorbike accidents is that people forget to
retrieve side stand, i.e. about 36 % of accidents are caused by
forgetting to retrieve the side stand
⮚ We propose an automated motorized side stand retrieving system
that automatically retrieve side stand
3

4. 2.Problem Definition
⮚ The side stand is used for supporting a parked motorcycle
⮚ When the driver starts the motorcycle, there may be a possibility that
they forget to release the side stand that will cause unwanted troubles
and accidents
4

5. 3.Innovation Proposed
⮚ Automating the retrieval of side stand using motor when user starts
two wheeler by self starting .
⮚ When the rider stops and switch off key of two wheeler, the side stand
will slide down
5

6. 4.Literature Review
Author Title Journal Publishe
d on
Information
R. Selvendran,
Anlin J P,
Mohamed
Ashik N,
Mohamed
Riyas K
Design and
Fabrication of
Automatic Side
Stand Lifter for Two-
Wheeler
International
Journal of
Engineering
Research &
Technology
18-05-2019
ETEDM
VOLUME 7
– ISSUE 06
● 36%of accidents
caused by forgot to
retrieve side stand
● Different types of side
stand
P. Vijay, S.
Vinobalaji, A.
Dyson Bruno
Automatic Side
Stand Retrieving
System for two
Wheelers
International
Journal of
Engineering
Research &
Technology
18-05-2019
ETEDM -
VOLUME 7 –
ISSUE 06
● About axile
● It is a side stand
retrieving mechanism
using sprocket
6

7. 5.Methodology
Problem
Identification
Solution
Cost Analysis
Design
Calculations
Purchasing
Design
Initialisation
Construction
(24-8-2019) (28-8-2019)
(29-8-2019)
(18-9-2019) (16-9-2019) (14-9-2019)
(20-10-2019)
7
Final
Presentation
(23-10-2019)

8. 6.Working Mechanism
Side stand Retrieval
◆ Initially rider start the key switch of two wheeler and th engine starts.
◆ At the time when the rider puts the gear, the side stand retrieves. i. e.
At the beginning when the engine starts,the neutral indicator on the
meter of two wheeler turns ON.
◆ When the rider puts the gear, the neutral indicator turns OFF.
◆ The relay's input coil is connected parallel to the neutral indicator.
After side stand retrieves,the circuit breaks using a limit push switch.
8

9. Sliding Down of Side Stand
◆ To slide down the side stand,input coil of another relay is connected parallel to
the circuit which passes through the key switch of bike to complete the circuit
of horn like equipments.
◆ So when we switch off the key switch,the relay's input coil current will stop.
◆ When the normally closed path of the circuit of relay closes ,the sliding down
of the side stand will takes place.
◆ And after the side stand reaches the maximum position, a limit switch fixed
near the maximum distance will break the circuit.
9

10. 7.Components and Specifications
1. DC Motor (₹180)
• 12 volt
• 45 rpm
• 2Amps
2.Side Stand (₹110)
• Length 170mm
• Weight
3. Gear Box(₹150)
• Speed Reduction by Spur Gears (cast iron)
• Overall reduction ratio=1:4
• Reduce 45rpm to 11.25rpm 10

11. • Gear1
Module =1,pitch circle diameter =44mm,
addendum =46mm,number of teeth =44 nos
• Gear 2
Module =1,pitch circle diameter =22mm,
addendum =24mm, number of teeth =22 nos
4.Ball Bearings(₹110)
• HCH 6201 2RS, ID-12mm, OD-32mm, Deep Groove Ball Bearing
(12x32x10) (2 no. s)
5.Push Button Micro Limit Switch (2no.s)(₹100)
KW7-0 AC125V/250V 15A Momentary NO/NC SPDT
11

12. 6.Relay Switch (2no.s) (₹30)
12VDC, SPDT,
Load Current Max.: 7Amps 250V AC or 10Amps 28V DC.
Coil Resistance: 360-440 Ohms.
7.Helical Spring (1no.s)(₹10)
• Spring index (C) =spring diameter /wire diameter
=5mm/0.5mm
=10mm
12

13. 8.Project Progress
⮚ Initially a frame of angle iron is constructed to hold the side stand
⮚ Then a Gear Box is constructed to reduce the speed of motor from
2400 rpm to 600 rpm
⮚ Gear Box is bolted to the frame
⮚ DC Motor with 2400rpm is attached to the driver shaft of the Gear Box
⮚ Side stand is attached to the drive shaft of the Gear Box having
600rpm
⮚ Electrical connections are on progress
⮚ The project will finish at 21st October 2019
13

14. 9.References
⮚ P. Vijay, S. Vinobalaji, A. Dyson Bruno, 2019, Automatic
Side Stand Retrieving System for two Wheelers,
INTERNATIONAL JOURNAL OF ENGINEERING
RESEARCH & TECHNOLOGY (IJERT) ETEDM
⮚ R. Selvendran, Anlin J P, Mohamed Ashik N, Mohamed
Riyas K, 2019, Design and Fabrication of Automatic Side
Stand Lifter for Two-Wheeler, INTERNATIONAL JOURNAL
OF ENGINEERING RESEARCH & TECHNOLOGY (IJERT)
ETEDM
14

15. Thank you….
15