W181 User manual-.pdf

User Manual of W181GSM/WiFi Alarm System Operation lnstruction
�
'
-
User Manual o
f W181
GSM/WiFi Alarm System
'
,
'
1
"
/Jxdf!R "i" : 1 2 5 * 1 8 5 m m
� H R "i" : 2 5 0 * 1 8 5 m m
t
;J- � : 68g��
�ij:QiiJ'.(E'.� �ts

r Readmo carefully b
e
fo
r
e handle
7
L Keepmq the user manual reserved _J

CONTENTS
Explanation 2
Chapter 1 lntroduction 6
Chapter 2 lnstallation 8
Chapter 3 Operation a n d Setting 9
Chapter 4 SMS C o m m a n d 25
Chapter 5 APP Remote Control 28
Chapter 6 Alarm a n d remote operation 32
Chapter 7 Technical Parameters 33
Chapter 8 lnstallation of Detectors 34
Chapter 9 Troubleshooting 36
P 1
Product Explanation
The Host: The receiver a n d control center of a l a r m system
Remete Control: Swtich the mode of Host i n Arm/Disarm/Home a r m . Or
for emergency a l a r m , but needs to connect with the host first.
Detector: lnstall in the area needs to be detected, send the a l a r m signal
to the host, with P I R /Motion detector, Door window detector,
Smoke detector, Gas/CO detector, etc. Need to connect with
host first.
Arm: in arm mode, any detectors are triggered, the host will make an alarm
Diarm: i n disarm mode, only the detector in emergency zone a n d e l d e r
h e l p i n g zone is triggered, the host will make an a l a r m . Others
not.
Home arm: i n arm mode, the host will not make a n a l a r m if the detector
i n home zone is triggered. But detectors i n other zone still can
trigger a n a l a r m in this m o d e .
Alarm number: a n auto-dail phone n u m b e r w h i l e the host a l a r m s .
CID number: the p h o n e n u m b e r of a l a r m center, the host send a l a r m
message to this n u m b e r address.
Help number: the auto - d a i l phone n u m b e r w h i l e the detector i n e l d e r
h e l p i n g zone is triggered.
SMS n u m b e r : The phone n u m b e r of s e n d i n g a l a r m message to the user
w h e n the host a l a r m s
Voice call: use the a l a r m host as a m o b i l e phone to make calls
Delay arm: after the user arm the system by host button or remote control,
the host will delay a w h i l e before enter into arm mode.
Delay a l a r m : after the host receive the a l a r m signal from the detector, it
will delay a w h i l e before a l a r m s .
Remete control: Use the p h o n e or m o b i l e phone to d i a l the S I M n u m b e r
bound to the host. Then control the host after it answered.
APP control: Use the TUYA a p p in your smart phone to control the host.
System password: when locking the keyboard, i n p u t the password of the
keyboard; When c a l l i n g to the host for remote control, needs
to be i n p u t is fo u r digits, the factory password setting is 1234.
P2

System vol u me: the vol u me of the system voice p ro m p t when operating
the host
System voice: whether voice prompt is required w h e n operating on the
host
Alarm time: the ti m e of siren gives a l a r m , i n m i n u t e s
SMS reply: refers to whether the host automatically replies to the SMS
after receiving the SMS when the user sets the host parameters
by s e n d i n g SMS
Alarm output: when the host a l a r m , whether to output relay short circuit
at the same time
Remote Control Voice Setting: when using the remate control to arm or
disarm the host, the host voice prompts the system in a l a r m
mode a n d gives " D I " notification s o u n d .
Timing Arm & Disarm: set a group of Arm and Disarm time, so the host will
enter into the arm or disarm state automatically at the set time.
User serial code: w h i l e connect to network, the n u m b e r of the host in the
networking center, composed of fo u r digits.
Center precision: the requirement of h a n d s h a k e signal precision when the
host interacts with the network center computer
Arm/Disarm upload: w h e n the host changes the Arm/Disarm status,
whether to u p l o a d the Arm/Disarm information to the network
center
Self inspection time: i n order to keep connection with the network center,
the detection information s h a l l be u p l o a d e d to the network
center regularly
Self inspection in week: i n order to keep connection with the network
center, it is necessary to regularly u p l o a d the detection
i n fo r m a ti o n to the network center
Backlight power saving: whether the display screen s h o u l d be t u rn e d off
to save power w h e n the host is u n a tt e n d e d
Anti Tamper switch: the host with a switch to prevent d i s m a n t li n g , choose
to a l a r m when the host is d i s m a n t l e d or not
lllegal Arm: set the illegal arm function, which can prompt you whether
the doors a n d windows are closed w h e n you go out.
Recording: users can record a s o u n d by the host i n advance. When there
is a n a l a r m , the host d i a l s the a l a r m p h o n e . After the p h o n e is
connected, you can h e a r the recording on the phone, such as
"XX has a n a l a r m " a n d so on
P3
Networking event code: it is used to define the alarm information attribute
of the zone a rea, such as theft a l a r m , gas alarm, etc., which is
represented by 3 digits
Alarm siren: when the detector in a certain zone area a l a r m s , turn on the
siren of the host or not.
Type of zone area: the attribute of zone a rea. There are 8 options.
Common zone area: the host o n l y works when it is armed or in home arm
status, a n d there is no response when it is d i s a r m e d .
Home zone: when the host enters the home arm status (press the home
key on the host keyboard or the h o m e key on the remate
control), the type of zone is that the detector in the home zone
will not a l a r m if it is triggered. Note: if a user is e q u i p p e d with
two accessories, one is a door magnet, the other is a n infrared
detector, the door magnet is in zone 1, and the infrared detector
is in zone 60 home zone), At this time, the user presses the
home key of the remate control to make the host enter the
home arm state. When the user walks a ro u n d the home, the
infrared detector w i l l detect the movement of the h u m a n body
a n d send out a s i g n a l , but the host w i l l not respond. However,
when the door magnet of zone 1 ( o r d i n a r y zone) is opened, the
host will immediately give an a l a r m .
lntelligent zone: in the status of arm, when the detector i n the zone is
triggered once, the system w i l l not give a n a l a r m immediately.
lt will give a n a l a r m o n l y if it is triggered again within 5 ~ 30
seconds after the first trigger.
Emergency zone: no matter i n Arm or Disarm status, as l o n g as the detector
is triggered, it w i l l a l a r m . lt is generally used to connect smoke
sensor, gas detector a n d emergency button.
Shut down zone: no matter i n arm or disarm status, the detector w i l l not
a l a r m w h e n it is triggered.
Chime zone: no matter in Arm or Disarm status, as long as the transmitter
in c h i m e zone is triggered, the host will give a c h i m e sound
"DingDong".
Welcome zone: I n d i s a r m status, the transmitter i n welcome zone is
triggered, the host will give a sound "Welcome". I n arm status,
the host w i l l a l a r m when the transmitter is triggered.
Elder helping zone: no matter the in arm or d i s a r m status, the transmitter
of the e l d e r h e l p i n g zone is triggered, the host will voice prompt
P4

" e l d e r h e l p i n g in a zone", a n d d i a l three groups of h e l p i n g
n u m b e r s .
Dial the number of the zone: w h e n setting the a l a r m n u m b e r of a zone, it
defined which groups of a l a r m n u m b e r s s h o u l d be d i a l e d , a n d
three groups of h e l p n u m b e r s s h o u l d be d i a l e d far the e l d e r
h e l p i n g zo n e .
System time: the system time a n d date of the a l a r m .
Alarm record: the information of each a l a r m of the host is recorded,
i n cl u d i n g the zone n u m b e r a n d the a l a r m date, far the user to
query, a n d it can record u p to 102 groups.
Arm/Disarm record: each arm a n d disarm of the host will be recorded,
i n cl u d i n g arm a n d disarm action, time, date,method, etc., it can
record u p to 72 g ro u p s .
P5
Chapter 1 lntroduction
1.1 System introduction
This is a high-end G S M / W I F l ( 2 .4 G ) a l a r m system with 1. 7 - i n c h TFT color
screen, touch keyboard, and built-in powerful CPU master, more stable and
r e li a b l e i n performance. The p a n e l supports wireless connection with P I R
motion sensors, door contacts, smoke detectors, gas detectors, remate
controls, emergency buttons, a n d other accessories. When the panel host
received any alarm notification, the host screen w i l l d i s p l a y the a l a r m zone
immediately, with 80 d B siren s o u n d on site, u p to 110 d B siren s o u n d by
connecting externa! h o rn . at the same time the panel will push a l a r m
message by GSM card and c a l l the user's n u m b e r s by preset in the system.
By p u s h i n g the a l a r m notices to the bound m o b i l e p h o n e through W i F i. lt
is widely used in fa m i l i e s , factories, schools, shops, convenience stores,
fi n a n ci a ! rooms, villas, residential areas a n d other places that need to be
protected to ensure the safety of people a n d property.
1.2 Feature
■ Colorful TFT color display, h u m a n i z e d m e n u a n d voice prompt, easy
to use
■ Support 99 zones and 8 zone types optional i n each zone; ON/OFF
siren i n each zone
■ 8 groups ti m i n g Arm/Disarm function, weekly ti m i n g optional far
each g ro u p to avoid m a n u a l l y arm a n d disarm frequently, truly
realizes smartly a n d automatic control.
■ The p a n e l will d a i l 6 g ro u p s of preset p h o n e n u m b e r when a l a r m
a n d no p h o n e n u m b e r s lost even power off
■ 10s automatic message recording function, Embedded artificial voice,
the user will know the a l a r m location a n d a l a r m zones remotely.
■ Remate arm and disarm, monitoring, speaking, switch alarm, switch
intelligent socket function.
■ Wireless intelligent connecting 1527 full range of accessories,
support to connect 100 remate controls a n d 100 detectors
■ Telephone (mobile phone) or sending SMS to control the host system
remotely, innovative c o m p a ti b l e with C h i n a M o b i l e Feixin function,
P6

□
2 3
Ar m / H o m e A r m
Key
4 5 6 Disarm Key
9
Return key
7 8
D
o
., Confirm Key
*
-
1
M e n u
Host Touch Keypad and Side View
, ......
□
1 2 3 ..
4 5 6 ..
7 8 9
!)
*
o - ✓
�
Front View
S I M Card Slot
On/off button
Chapter 2 lnstallation
USB Port
Horn interface--,.A■
The p a n e l s h o u l d be installed in the central position of the g u a r d a rea to
receive a ll signals from detectors. Keep away from large metal objects or
a p p l i a n c e s with high-frequency interference, m e a n w h i l e , avoid the
reinforced concrete w a l l s a n d tire doors barriers, etc.
in arder to save costs users send S M S to the host system settings
a n d S M S .
■ Can use a p p to set a n d manage the p a n e l host, support IOS /
A n d ro i d operating system. The host can be used a s a n o r d i n a r y
m o b i l e phone, which can make calls directly.
■ One way of alarm linkage wireless relay, one way of linkage wireless
sound and light siren, can be connected to the wired horn to expand
the a l a r m v o l u m e .
■ lntegration of high-precision clock c h i p , time will not be disrupted
d u e t o power fa i l u r e .
■ The u n i q u e b l a c k box function can display the latest 72 a r m i n g a n d
d i s a r m i n g records a n d 102 latest a l a r m records. Display the a l a r m
ti m e a n d area code accurately.
■ 2 sets of C I D numbers, can be connected with large central
computers, a n d co m p a ti b l e with l n t e rn a ti o n a l network a l a r m
Contact I D protocols.
■ with low power r e m i n d e r a n d anti tamper function.
■ B u i l t in rechargeable high-capacity li t h i u m battery, automatically
switch to stand by s u p p l y w hen power fa i l u r e .
■ with SMS r e m i n d e r a n d c a l l i n g when power-off.
■ The panel host adopts 850/900/1800/1900MHz GSM / GPRS module.
P7 P8

/Anti-tamper key
�
'/'
=
=
=
=
=
8=
=
&
==z=
�
,
w
Panel Back View
Prompt Display"Disarm" Host in disarming status
information
Display"Arm" Host in arming status
display
Display"Home Arm" Host in home arming status
Display"XX Zone is Host in alarming status with specific defense zone
alarming"
Display"97 Zone is 97 Zone is alarming cause manual disassembly or moving
alarming" the Host. Anti-tamper a l a r m .
W I F I connect Host Keypad connect WIFI
SIM icon is blinking Host did not detect SIM card
Chapter 3 Operation & Setting
3 . 1 lnitial Power-on
According to the installation method, insert the S I M card to the card slot
of the host panel, t h e n connect host with power a n d long press [ON/OFF]
button. Now then, host voice prompts "Welcome to smart voice alarm".
At the same ti m e the host starts self-testing GSM network, "GSM signal
LED" flashing (flash once for 15) when searching the GSM S i g n a l. U n ti l
network working properly, S I M Card icon w i l l disappear, means GSM signals
and S I M card working normal. lf it keeps fl a s h i n g m e a n s not detecting S I M
card or something is wrong with S I M card. Host Keypad shows not connect
with W I F I.
pg
3.2 Arm
Arm refers to a full range of on-site alarm detection alert when nobody at
home; AII detectors are i n working state, w h e n there is danger (theft, tire,
gas l e a k etc) trigger the detectors, the host alarms immediately. After
a r m i n g operation, it displays a n d locks "ARM" icon.
Remate Control operation: press key [ARM] once.
Keyboard operation: press key [ARM] once.
3.3 Disarm
Disarm refers to host panel stops the a l a r m or make the alarm system in a
non-alert state. After d i s a r m i n g , when detectors are triggered, but host
doesn't alarm (except the detectors of emergency zones and the emergency
button on remate control). After d i s a r m i n g operation, it displays and locks
"Disarm" icon.
Remate Control operation: press key [ D i s a r m ] .
Keyboard operation: press key [ D i s a r m ] .
3.4 Home Arm
H o m e Arm refers to w h e n s o m e o n e at home, a n d for safety, the detectors
i n the perimeter area like doors, windows, balconies are in working state
but the detectors i n d o o r don't work i n case of the false a l a r m i f triggered
by user himself, t h e n the user chooses H o m e Arm to let sorne detectors
work a n d other detectors not work. H o m e Arm function needs to be set
that is the defense zones of the interior detectors s h o u l d be changed to
be H o m e Arm zones in order to work properly. After H o m e Arm operation,
it displays and locks " H o m e Arm" icon.
Remate Control operation: press key [STAY].
Keyboard operation: press key [ARM] twice.
3.5 Emergency Alarm
When a n emergency occurs, press p a n i c key on the remate control to
enter emergency a l a r m state.
Note: if the host password keyboard protection function is turned on,
the password needs to be input befare the operation to the keyboard,
and the initial password is 1234.
P 1 0

N u m b e r Settings Number Settings
� tri @ o
l .Alarm numbers
1 6 : 3 0
2 . C I D numbers
3 . H e l p numbers
1 3 - 1 1 - 0 8 THU
� � � [i)
4 . S M S numbers
Arming
5.Voice calls
O K . E n t e r E S C . Return O K . E n t e r E S C . Return
3.6 Set Phone No.
The host can m a x i m u m set 6 groups a l a r m N o . , 2 groups C I D No., 3 groups
H e l p No., 6 groups SMS message No. The m a x i m u m length of every g ro u p
p h o n e N o . is 30 digits. Please fi n d settings as below:
3.6.2 Set C I D No.
As shown in picture 3-1, press key [ UP/DOWN l to select [ 2. CI D N o . ]
a n d press key [ O K ] or input 2, t h e n i n p u t g ro u p n u m b e r (1-2), then
i n p u t CID n u m b e r like 88889999 a n d press key [ O K ] to save. Then press
key [ BACK] to return to desk page.
3.6.5 Phone Call
As shown i n picture 3-1, press key [UP/DOWN] to select [5. P h o n e Call]
a n d press key [OK] , then i n p u t p h o n e n u m b e r like 10086. Press key
[OK] to start c a ll i n g . Press key [BACK] to h a n g u p .
3.6.4 Set SMS Phone No.
As shown i n picture 3-1, press key[UP/DOWN]to select [4. SMS P h o n e
No.] a n d press key [OK] or i n p u t 4, then i n p u t g ro u p n u m b e r (1-6), t h e n
i n p u t p h o n e n u m b e r like 13812345678 press key [OK] to save. User can
set 6 groups a l a r m p h o n e n u m b e r s at most. Then press key [BACK] to
return to desk page.
Delete SMS Phone No.
As shown i n picture 3-1, after entering to the settings of SMS P h o n e No.,
press key [ M e n u ] to delete H e l p P h o n e No. a n d press key [OK] to save,
then press key [BACK] to return to desk page.
3.6.3 Set Help Phone No.
As shown i n picture 3-1, press key [UP/DOWN]to select [3. H e l p P h o n e
No.] a n d press key [OK] or i n p u t 3, then i n p u t g ro u p n u m b e r (1-3), t h e n
i n p u t p h o n e n u m b e r like 13812345678 press key [OK] to save. User can
set 3 groups a l a r m p h o n e n u m b e r s at most. Then press key [BACK] to
return to desk page.
Delete Help Phone No.
As shown i n picture 3-1, after entering to the settings of H e l p Phone No.,
press key [ M e n u ] to delete H e l p P h o n e No. a n d press key [OK] to save,
Delete CID No.
As shown i n picture 3-1, after entering to the settings of C I D numbers,
press key [ M e n u ] to delete a ll the C I D N o . a n d press key [OK] to save,
Emergency
Disarm
Arm
Stay
Picture 3 - 1
3 . 6 . 1 Set Alarm Phone No.
As shown in picture 3-1, press key [ UP/DOWN l to select [ 1. Alarm
Phone N o . ] a n d press key [ O K ] or i n p u t 1, t h e n i n p u t g ro u p n u m b e r
(1-6), then i n p u t p h o n e n u m b e r like 13812345678. User can set 6 groups
a l a r m p h o n e n u m b e r s at most. Then press key [ BACK] to return to desk
page.
Delete Alarm Phone No.
As shown in picture 3-1, after entering to the settings of a l a r m p h o n e
numbers, press key [ M e n u ] to delete the a l a r m p h o n e n u m b e r a n d
press key [ O K ] to save, then press key [ BACK] to return to desk page.
P 1 1 P 1 2

Add Accessories
1 .Add Remole Control
2.Add Detector
3.Del Remole Control
4. Delete Detector
5.Smort Accessories
O K . E n t e r E S C . Return
Add Remote Control
Enter Numberl00-991
Ioto! · nn1
Add Detector
Enter Numberi00-991
Total · nnn
3 . 7 . 5 lntelligent Accessories
As shown i n picture 3-2, press key [1. Add Remate Controls] . With the
voice prompt "Please i n p u t n u m b e r s : " { O means siren, 9 m e a n s a l a r m
relay), t h e n press key [Arm] a n d host s e n d open signals; press key
[Disarm] a n d host send clase signals.
3. 7 .4 Delete Detectors
As shown in picture 3-2, press key [4. Delete Detectors] . With the voice
p ro m p t "Please i n p u t n u m b e r s {01-99)"{ e.g. delete Zone N o . 1 remate
control, t h e n i n p u t 01; delete Zone N o . 22 remate control, i n p u t 22;
delete a ll by pressing key [ARM] ), t h e n press key [OK] .
3. 7 .2 Delete Re mote Control
As shown in picture 3-2, press key [3. Delete Remate Control] . With the
voice prompt "Please i n p u t n u m b e r s { 0 1 - 9 9 ) " { e.g. delete No. 1 remate
control, t h e n i n p u t 01; delete N o . 22 remate control, i n p u t 22; delete a l l
by pressing key [ARM] ), then press key [ O K ] .
3. 7 .3 Add Detectors
As shown in picture 3-2, press key [2. Add Detectors] . With the voice
p ro m p t "Please i n p u t zone n u m b e r s {01-99)"{ e.g. Study Zone No. 1
remate control, t h e n input 01, study Zone No. 22 remate control, i n p u t
22), t h e n press key [OK] . At t h i s moment, trigger detectors to s e n d a
signal to host. Host voice prompts "Add Successfully" with [Add
Successfully] on display, which m e a n s detector has been programmed to
the host. lf voice prompts add repeatedly, it mea ns detector has been
a d d e d to the host already a n d couldn't be programmed repeatedly. T
o
l e a rn more detectors, trigger other detectors. The host can study as most
as 150 different detectors.
Solar Strobe Siren J1
Siren J009
3. 7 . 5 . 1 Code Match between Host & Wireless Strobe Siren
Code Match M e t h o d : I n strobe siren standby mode, long press key SET
u n ti l the a l a r m indicator lit constantly to enter l e a rn i n g state; Then on
intelligent accessories page, i n p u t N o . O, press key [ARM] or [DISARM] ,
host will send signal as shown in picture 3-2; wireless strobe siren will
beep twice a n d indicator fl a s h e s twice after receiving the signa 1, which
mea ns the code match successfully, t h e n press the SET key of strobe siren
to exit the l e a rn i n g state.
Check the Success of Code Match: after wireless strobe siren exit l e a rn i n g
state, press key [ARM] or [ D I S A R M ] to switch [Wireless Strobe Siren]
ON or OFF, if it's OFF, strobe siren will beep "di d i " ; if it' s O N , siren w i ll
a l a r m , whi ch m eans the host match code successfully with wireless
strobe s i r e n .
Send OK
Smart Accessories
Enter Number :
Disarm Key.OFF
Arming Key.ON
0.Siren 9.Alarm Outlet
Picture 3 - 2
Smart Accessories
Enter Number :
Disarm Key.OFF
Arming Key.ON
0.Siren 9.Alarm Outlet
Disarm Key.OFF
Arming Key.ON
0.Siren 9.Alorm Outlet
Smart Accessories
Enter Number :
P 1 3 P 1 4

3. 7 .5.2 Code Match between Host and Smart Socket
Code Match Method: I n smart socket standby mode, long press key SET
for Ss u n ti l the socket indicator light t u rn s out to enter l e a rn i n g state;
Then on intelligent accessories page, press key [ARM] or [DISARM] to
switch smart socket ON or OFF, host will send slgnal : Smart socket indicator
light flashes twice, w h ic h m e a n s the code match successfully, then press
the SET key of smart socket to exit the l e a rn i n g state.
Check the Success of Code Match: after smart socket exit l e a rn i n g state,
press key [ARM] or [DISARM] to switch smart socket ON or OFF, if it's
OFF, smart socket lit RED; if it's ON, socket lit BLUE, w h i c h means the host
match code successfully with smart socket.
System Settings
l .Del ay Settings
2.Password Settings
3. Volee Settings
4.Siren Settings
5.Phone&SMS Settings
Picture 3 - 3
Delay Settings
Arming delov.Dü]
Alarm delay:00
Picture 3 - 4
Password Settings
Password: 1 2 3 4
Keypad Lock:OFF
Picture 3 - 5
3.8.2 Password Set
On system setting page, press key [UP/DOWN] to move the cursor behind
[Password Set], then press key [OK] or n u m b e r 2 to enter password set
page, as shown i n picture 3-4.
3 . 8 . 1. 2 Delay Alarm Set
On del ay set page, press key [DOWN] to move cursor b e h i n d [Delay
Alarm T i m e ] , i n p u t the delay period(00-99s), 00 mea ns without de lay,
a l a r m i n g immediately, then press key [OK] to save the setting.
Smart Socket
3.8 System Set
On main page, press key [UP/DOWN] to move the cursor behind [System
Set] , then press key [OK] or n u m b e r 3 to enter system set page, as
shown in picture 3-3.
3.8.1 Delay Set
On system set page, put cursor on [Delay Set] , a n d press key [OK] or
n u m b e r 1 to enter delay set page, as shown i n picture 3-3.
3 . 8 . 1 . 1 Delay Arm Set
On delay set page, put cursor on [Del ay Arm T i m e ] , i n p u t the delay time
(00-99s), 00 m e a n s without delay, a r m i n g immediately, then press key
[OK] to save setting, as shown in picture 3-4.
P 1 5
3 . 8 . 2 . 1 System Password
On password setting page, input to u r digits new passwords i n System
Password (original password is 1234), press key [OK] to save.
3.8.2.2 Keypad Password
On password setting page, press key [DOWN] to move the cursor b e h i n d
[Keypad Password Set], press key [ M E N U ] to switch it ON or O F F a n d
press key [OK] to save setting. lf the lock function of keypad is open, host
w i l l lock w h e n it enters into d o r m a n c y or a l a r m state. U n l o c k the keypad
by i n p u tti n g the password. The factory default is unlocked.
3.8.3 Voice Setting
On system setting page, press key [UP/DOWN]to move the cursor b e h i n d
[Voice Setting], then press key [OK]or n u m b e r 3 to enter Voice Setting
page, as shown i n picture 3-6.
P 1 6

System Settings
1.Delay Settings
2.Password Settings
'3'.voice Settings
4.Siren Settings
5. Phone&SMS Settings
O K . E n t e r ESC. Return
Picture 3 - 6
Voice Settings
System volume:5
System voice:ON
Picture 3 - 7
Siren Settings
Built-in volume : 05
Siren on time:01
Picture 3 - 8
3.8.5 Phone Message Setting
On system setting page, press key [UP/DOWNho move the cursor b e h i n d
[Phone Message Setting], then press key [OK] or n u m b e r 5 to enter phone
message setting page, as shown in picture 3-8.
3 . 8 . 5 . 1 Message Reply
On phone message setting page, press key [ M E N U ] to switch it ON or OFF
a n d press key [OK] to save setting. lf switch on, the host w i l l s e n d
message to advise whether settings are correct when users do settings by
message. The factory default is on.
3.8.5.2 Alarm Output
On p h o n e message setting page, press key [DOWN] to move the cursor
b e h i n d [Alarm Output], press key [ M E N U ] to switch it ON or OFF a n d
press key [OK] to save setting. lf switch on, re lay will shortcut output w h i l e
the host a l a r m i n g , COM a n d NO shortcut. The factory default is o n .
3 . 8 . 3 . 1 System Volume
On voice setting page, put the cursor on [System Vol u m e ] , input vol u me
level 0-7, then press key[OKho save the setting. O m e a n s mute d u r i n g the
operation to host, a n d 7 m e a n the largest volume, as shown i n picture 3-7.
The factory default is level 5.
3.8.3.2 System Voice
On voice setting page, press key [DOWN] to move the cursor b e h i n d
[System Voice], press key [ M E N U ] to switch it O N or OFF a n d press key
[OK] to save setting. lf switch it off, there is no voice prompt o n l y button
voice d u r i n g operation. The factory default is o n .
3.8.4 Siren Setting
On system setting page, press key [UP/DOWN] to move the cursor b e h i n d
[Siren Setting], t h e n press key [OK] or n u m b e r 4 to enter Siren Setting
page, as shown in picture 3-8.
Phone&SMS Settings
SMS reply:ON
AlarmOutlet :ON
Picture 3 - 9
Sound Settings
Enter Numberl00-991: 01
Picture 3 - 1 O
Sound Settings
Siren Sound : ON
Picture 3 - 1 1
3.8.4.1 lnternal Siren Volume
On siren setting page, i n p u t v o l u m e level 0-7, then press key [OKho save
the setting. O m e a n s mute a n d 7 m e a n s the largest volume, as shown i n
picture 3-8. The factory default is level 5.
3.8.4.2 Siren Alarm Time
On siren setting page, press key [DOWN] to move the cursor b e h i n d
[Siren Alarm T i m e ] . The siren a l a r m ti m e is between 0-20 m i n u t e s , then
press key [OK] to save setting. O mea ns mute, the factory default is 1 minute.
P 1 7
3.8.6 Alarm Output
On system setting page, press key [UP/DOWNho move the cursor b e h i n d
[Re mote Control Voice Setting], t h e n press key [OK] or n u m b e r 6 to enter
setting page, as shown in picture 3-10. With the voice prompt "Please
i n p u t n u m b e r s : " ( No:01-99), t h e n press key [OKho enter next page; press
key [ M E N U ] to switch it ON or O F F a n d press key [OKho save setting, as
shown in picture 3 - 1 1. lf switch it on, it m e a n s the remote control w i l l
s o u n d " D I D I " when using t h i s n u m b e r e d remote control to arm a n d
d i s a r m . The factory default is o n .
P 1 8

3.8. 7 Scheduled Arm/Disarm
On system setting page, press key [UP/DOWN] to move cursor b e h i n d
[Scheduled Arm/Disarm], then press key [OK] or number 7 to enter setting
page, as shown in picture 3 - 1 2 . With the voice prompt "Please i n p u t
numbers:", enter No between 1-4; then press key [OK] to enter next page;
with voice p ro m p t i n p u t s c h e d u l e d arm ti m e , s c h e d u l e d disarm ti m e .
Move cursor b e h i n d s c h e d u l e d switch, press key [ M E N U ] to switch it ON
or O F F a n d press key [OK]to save setting, as shown i n picture 3-11. lf
switch it on, the host w i l l a u t o m a ti c a l l y arm a n d disarm i n preset ti m e .
3.8.8.4 Self Test Week
On re mote control voice setting page, press key [DOWN] to move cursor
b e h i n d [Self Test Week], i n p u t any week n o . 1234567, press key [OK] to
save setting.
3.8.9 Low Battery and Anti-tamper Setting
[Low Battery a n d Anti-tamper Setting], press key [OK] or n u m b e r 9 to
enter setting page, as shown i n picture 3-15 ..
3.8.8.3 Self Test Time
On remote control voice setting page, press key [DOWN] to move cursor
b e h i n d [Self Test Time] , i n p u t self test time, press key [OK] to save
setting.
3.8.8 Scheduled Arm/Disarm
[Network Center Setting] , t h e n press key [OK] or n u m b e r 8 to enter
setting page, as shown i n picture 3-14.
3.8.8.1 User Area Code
On remote control voice setting page, i n p u t to u r C I D code i n [User Area
Code] , press key [OK] to save setting. The factory default is 0000.
3.8.8.2 Arm/Disarm Upload
On remote control voice setting page, press key [DOWN] to move cursor
b e h i n d [Arm/Disarm U p l o a d ] , press key [ M E N U ] to switch [Not
U p l o a d ] / [Arm U p l o a d ] / [Disarm U p l o a d ] / [Arm/Disarm U p l o a d ] ,
press key [OK] to save setting. The factory default is [Not U p l o a d ] .
3.8.9.1 Back Light Power Saving
On low battery a n d anti-tamper setting page, on the item [Back Light
Power Saving], press key [ M E N U ]t o switch on or off a n d press key [OK]to
save setting. lf switch it on, TFT c o l o r display w i l l close to save power. The
factory default is o p e n .
Picture 3 - 1 7
OK.Enter ESC. Return
F u l l recovery
Please hoto <OK> key 1 O
seconds!
Picture 3 - 1 6
OK.Enter E S C . Return
Restare Factory
l .Part recovery
2.Full recovery
Picture 3 - 1 5
LCD Saved&Tamper
LCD Save: i5NI
Tamoer : O N
Ready t
o Arm, OFF
AC Failure:0
Language, English
3.8.9.3 lllegal Arm
On low battery a n d anti-tamper setting page, press key [DOWN] to move
cursor b e h i n d [lllegal Arm] , press key [ M E N U ] to switch on or off a n d
press key [OK] to save setting. lf switch it on, the host cannot arm if it fa i l s
to receive the signal sent by sensor closure. The factory d e fa u l t is close.
3.8.9.2 Anti-tamper Switch
cursor b e h i n d [Anti-tamper Switch] , press key [ M E N U ] to switch on or
off a n d press key [OK] to save setting. lf switch it off, the host will not
a l a r m i f anti-tamper switch is triggered. The factory default is open.
Picture 3 - 1 4
Testweek:
Test t i m e :
Arm&Disarm : No send
C I D Settings
User code : 0000
Picture 3 - 1 3
T i m i n g : ON
Week:
Disarm time :
Timing Settings
Armina time :
Picture 3 - 1 2
Timing Settings
Enter N u m b e r l l - 4 1 :
P 1 9 P20

3.8.9.4 Power Off Setting
cursor b e h i n d [Power Off Setting] , i n p u t 0-5, press key [OK] to save
setting. O m e a n s close prompt function, 1 means AC off, 2 m e a n s d i a li n g ,
3 means dialing siren, 4 means dialing linkage, 5 means dialing+siren+linkage,
The factory default is O.
3.8.10 Restare Factory Setting
I n the system setting page, press [up/down] key to move cursor to the
[Restare Factory Settings]. Then, press [OK] button or press key [O] directly
to enter into the Restare Factory Setting page, as shown in Figure3-16.
3 . 8 . 1 0 . 1 Partial Restoration
After entering into Restare Factory Setting page, press [OK] button, the
host will remind whether to restare factory settings. After restoring factory
setting, the remate controls a n d detectors added befare would not be
deleted, but a l l the other parameters w i l l be restored to the factory state.
3.8.10.2 Full Restoration
After entering into Restare Factory Setting page, press [2] key a n d then
l o n g press [OK] key u n ti l a host reboot is completed. I n t h i s situation, a l l
the remate controls a n d detectors w i l l b e deleted a n d a l l the parameters
will be restored to factory state, as shown in Figure3-17.
Zone Settings
º tri @ o
� 0 � [i]
Zone Settings
Enter Numberl00-991: 01
Zone Settings
CID Event code: l 30
Siren : O N
Types: A
W
A
Y ARMED
Zone dial : l 23456
On m a i n m e n u . as shown in picture 3-18, press [UP/DOWN] key to move
the cursor at [Recording] , then press key [OK] or n u m b e r 4 directly to
enter recording setting page, as shown in picture 3-19; On recording setting
page, press key [BACK] to return to the m a i n m e n u ; Press any key to start
recording. The recording time is 10s, as shown i n picture 3-20. The
recording s h o u l d be brief, e.g. "This is XXX's house, it's intruded illegally,
please help".
Host w i l l exit a u t o m a ti c a l l y after 10s, a n d user can press any key to e n d
recording d u r i n g recording process.
3.10 Zone Management
On the m a i n m e n u page, as shown in Figure 3-21, press [ U p / Down] key
to move the cursor to the zone management. Press [OK] button or press
n u m b e r 5 directly to enter zone management page, as s h o u l d in Figure
3-22. Then i n p u t the zone n u m b e r (1-99) a n d press [OK] to enter the next
level m e n u . Zone attribute setting m a i n l y includes networking feature code
setting, built-in siren on/off s e tti n g , zone type setting, d i a li n g g ro u p w h e n
a l a r m i n g a n d wired zones open/closed alarms, etc as shown in Figure 3-23.
The setting is as follows:
Message Record
ii tti @ O
� 0 � [i]
Picture 3 - 1 8
Message Record
Press l to stort recording
Picture 3 - 1 9
Message Record
Recording ...... 09
Picture 3 - 2 0
Picture 3 - 2 1 Picture 3 - 2 2 Picture 3 - 2 3
3.9 Recording Setting
Host will play the preset recording after d i a l i n g the preset a l a r m number.
And the recording setting method is as below:
3.10.2 lnternal Siren On/off
After entering the next m e n u , press [Down] key to move the cursor to
[Alarm alerting] .Press [ M e n u ] key to switch ON a n d O F F and t h e n press
[OK] to save. lf you select Off, it indicates that host will not alert when the
detectors in that Zone receives a l a r m s .
3.10.1 Network Even Code
After entering next level menu, i n p u t event code in the Networking Event
Code. 100 m e a n s m e d i c a l aid, 110 represents fire, 1 2 1 denotes robbery,
122 denotes a noiselessly rob, 130 represents burglary, 13 1 denotes the
perimeter burglary, 1 5 1 denotes gas leakage. Press [OK] to save.
P 2 1 P22

3.10.3 Set Zone Type
After entering the next level m e n u , press[DOWN] key to move cursor to
[Zone Type]. Press [ M e n u ] key or press n u m b e r s directly to select: [1]
N o r m a l , [2] Stay, [3] lntelligent, [4] Emergency, [s] Close, [6] doorbell,
[7] Welcome, [8] H e l p the Senior, then press key[ OK] to save.
WIFI Settings
º tíi @ o
� 0 � raJ
Picture 3 - 2 7
WIFI Settings
0.APConfig
l .W I F I C o n fi g
2 .W I F I R e s e t
Picture 3 - 2 8
3.10.4 Set Sub Zone Dialing
After entering the next m e n u , press [Down] key to move the cursor to
[Zone D i a li n g ] . I n p u t user n u m b e r when t h i s Zone a l a r m s . lt can be any
desired p h o n e groups a m o n g 123456, but if the zone type is for [ H e l p the
senior], the g ro u p is fixed to h e l p n u m b e r and can't be set, then press
[OK] to save.
3 . 13 Check Records
On the m a i n page, press [ U p / Down] to [Version Records], then press [OK]
button or n u m b e r 8 into checking version records page, as shown 3-29,
3-30 [Record query] i n cl u d e s a l a r m records a n d arm/disarm records, 3-31
[Version query] you can see the model, software version n u m b e r and I M E I
code of GSM m o d u l e .
3 . 11 Clock Management
On the m a i n page, press [ U p / Down] key to move the cursor to [clock
management], then press the [OK] button or press n u m b e r 6 to enter clock
m a n a g e m e n t page. Press [ M e n u ] button to switch the display format of
the date, and press [ U p / Down] key to switch a m o n g year, month, date,
hour, minute and second; Press n u m e r i c key to i n p u t the n u m b e r s t h e n
press [OK] to save, as shown in Figure 3-26.
Clock Settings
vv-MM-dd
1 5 - 0 7 - 2 4 0 9 : 1 6 : 52
System&Version
� tíi @ o
� 0 � raJ
Picture 3 - 2 9
History&Version
l .Historylist
2.System Version
Picture 3 - 3 0
History List
l.Alarmllst
2.Arm&Disorm list
Picture 3 - 3 1
3 . 1 3 . 1 Alarm Records
On [Check Records] page, press [OK] key to enter [Alarm Records], as
shown i n picture 3-32. Press key [UP/DOWN] to check a l a r m records. At
most 102 records can be saved, and each record i n cl u d e s information like
record number, a l a r m date, time, zones etc.
Picture 3 - 2 6
3. 12 W I F I Configuration
I n the m a i n page, press [ U p / Down] to [WIFI configuration], t h e n press
[OK] button or press the n u m b e r 7 to enter W I F I configuration page, as
shown 3-27, when configuring W I F I , Please press W181 keypad n u m b e r O
(AP configuration) 1 (intelligent configuration), if you want to cancel a l i
users, please press keypad n u m b e r 2, as shown 3-28.
P 2 3
3 . 1 3 . 2 Arm/Disarm Records
On [Check Records] page, press [UP/DOWN] key to move the cursor to
[ Arm/Disarm Records] a n d press [OK] or n u m b e r 2 to enter [ Arm/Disarm
Records] page, as shown in picture 3-33. Pres[UP/DOWN]to check Arm/
Disarm records. As most 72 records can be saved, a n d each record includes
information like record number, Arm/Disarm date, ti m e a n d mode, etc.
P24

Chapter 4: SMS Setting a n d C o m m a n d Chart
3 . 13 . 3 Check Product Version
On m a i n m e n u page, as shown i n Figure 3-34, press [UP/DOWN] to move
t h e cursor to [ Check Product Version] a n d then press [OK] or n u m b e r 8
directly to enter to the version checking page. Users can see the m o d e l
n u m b e r of the product, software version a n d GSM m o d u l e I M E I code, as
shown i n Figure 3-34.
I n a d d i ti o n to set para meter t h ro u g h host m e n u , SMS or Faction Message
can also set host parameters. The form is as below: [ System Password]
+ [ C o m m a n d N u m b e r l + para meter 1+para meter 2+parameter 3+
para meter 4. AII co m m a n d s begin with system password, a n d 1234 is
system's i n i ti a l password. Users can c h a n g e system password a n d since
t h e n , users s h o u l d use the modified password, or host will not response to
t h e co m m a n d s .
NO.
Name
Command
Parameterl Para. 2 Para. 3 Para. 4 Example
No.
Disarm
o
#
12340#
1
Disarm
Arm
1
#
12341#
2
Arm
3
S
T
A
Y 2 12342#
S
T
A
Y
RelayON 3 12344#
4 RelayON
Relay OFF 4 12345#
5
Relay OFF
Check host 11 123411#
general
#
Check host voice volume,
6
parameters Siren's state, etc
Set phone 3 1~9 13899998888 # 12343113899998888#
No. Group 1-6 is (User can set 31 Set first group phone
common as the number) number
7 number; 7-9
is the senior
help number
8 Delete 3 1~9 # 123435#
Phone No. Delete 5th Phone No.
9 Check 30 # 12343008#
phone No. 01~09, Check 8th Phone Number
1-9 arouo
4 1~8; 13899998888 # 12344113899998888#
SetSMS
Group 1~6 is (User can set Set first group phone
number
SMS number: 31 as the number) number
10
and central
7~8 is central
number
number
11 Delete 4 1~8 # 1234435#
Phone No. Delete 5
th
Phone No.
12 Check 4
0 01~08, # 123443008#
phone No. 1-8 group Check 8
th
Phone Number
13 Set system 50 Four any # 1234509876#
password figure among Set user password as 9876
0-9
14 Delay Arm 51 00-99 # 12345130#
period Set Delay Arm Period as 30s
setting
15 Delay 52 00-99 # 12345230#
Alarm Set Delay Alarm Period as
Period
305
setting
16 Set Alarm 53 00-20 12345305#
Siren Minutes Set Alarm Siren Period as 5
Period Minutes
17 Date 56 20150520 203000 # 12345620150520203000#
/Time Set time as
setting 2015//20/20:30:00
18 Check 56 # 123456#
system
Check system time
time
19 Arm/Disar 57 01-04; # 1234577017080018001234
m at fixed 01-04 group
5#
time fixedtime
Set the first fixed time, Arm
automatically at 8:00 form
Monday to Friday, disarm
at 18:00
20 Check 57 01-04; # 12345701#
Arm/Disarm 01-04 group Check the first group o
f time
at fixed time fixed time far Arm/Disarm
21 Set Zone 60 01~99; 1-Normal Zone 1-Sire # 1234601880#
Attributes 01-99 Zone
2-STAY Zone
n o n Set zone 18 as Help the
3-lntelligent Zone
when Senior Zone, Siren doesn't
4-Emergency Zone
alarming alert when alarming.
5-Close Zone
2-Siren
6-Doorbell Zone
7-Welcome Zone
offwher
8-Help The Senior
alarming
Zone
ESC. Return
Picture 3 - 3 4
System Version
V
e
r : ERDF1548645485
I M E I : 86719021261619
MAC :150206K6
O K . E n t e r
ESC. Return
O K . E n t e r
Picture 3 - 3 3
Ti m e :
D a t e :
Arm&Disarm list
001 History
Status:
ESC. Return
O K . E n t e r
Picture 3 - 3 2
Alarm list
001 History
Alarm zo n e :
A l ar m t i m e :
Alarm date:
P 2 5 P26

" - •
.
,_
_
'"""""
- .
,...- °'""°'"'""""-
-
"
• •
.
,
.,.,
-- •
u....
.. .,
,.
- .,...,.,,,. ,
_ ...,_............
--- ·-�
- m-
m--
·
·
-
......,_
m
=
"
•
" '"
•
.,..,....
- ........,,,-,__.,.
-
" -- •
.
,...
.
~· •
,._,__�
�- ·
�
-
- - -
- , �.. .... ,. ...,_..,.,..., ...,_
-
e- .. -.--�
,_,
-·
-
" - "
.
,...
. •
,,,..,...,
- ·�- °'"""""'"' ...'"
·
-
- --
-
-
"
•= •
- •
,,
_
- ·-·
!otlCD-0.
-
_,
• •
"
� •
,,...,..
-· .........,....., .........
- '
-
"
•
"
-- •
""""'
-
,__
---
·-
,__
-
- ·-�
-·-
• •
" ��- •
,,...,_..
00- -00 '"'°""""' ....
-
"
• •
-
,,,.,..,
•
,,....,,.00,.
�- - - ...-.
.,,..._
- "°'""°"----
" ·
- - -
,,_
·
-
-
•
•
Notice:"1234u i
n a
b
ove chart indicates sys
t
e
m password. Use
r should
u
s
e t
h
e n
ew password i
s t
h
e u
se
r has change t
h
e password.
Chapter 5:APP remote control
Sean t
h
e Q
R c
o
d
e
, o
r search f
o
r "
T
U
Y
A SMART" i
n A
p
p s
t
o
r
e o
r Android
mobile phone market t
o download and install.
Register
T
o open the "
T
u
y
a smart" app fo
r the fir
s
t time, users need t
o register a
n
account:
Network access configuration
lntelligent co
n
n
ecti
o
n
l
. connect the W1F1 router 1
n your h
o
m
e fi
rs
t
, make sure that the W1F1
router can connect t
o t
h
e externa! network normally, enter the app (all
devices] page, click the [
a
d
d device] r
cc
n
, select t
h
e WiFi connector i
n t
h
e
other page, enter the WiFi input page, then enter !he WiFi s
e
c
r
e
t c
od
e
,
and click (confirm) t
o e
n ter the start configuration page
Smart connection
l
. Connect the mobne phone t
o t
h
e W1Fi router a
t home first, make s
u
r
e
that t
h
e W1Fi router a
t home ca
n connect t
o the Internet normally, enter
the app [all devices] page, click the (
a
d
d d
ev
ic
e
) ic
o
n
, select the (WiFi
connector) i
n t
h
e "other" page, enter the W1Fi mput page, then e
n
t
e
r t
h
e
WiF1 code, and click (confirm) t
o enter the start configuranon p
a
g
e

"li 11' iil
t'r ..
•
....,_ ,.
,....,.
....,
,.
- -
"-
a
-
1
�
-
- ..ir..il&
E'"
. l)l
�
il'l
1. Please ensure that the equipment works normally (it i
s not i
n "alarm"
o
r "low power" state a
t present),
2
. Enter the app [ali devices] page, click the [add device) icon, and select
(WiFi connector] i
n the "other" page,
3
. O
n the [add device] page, click the [hot distribution network
(compatibility mode)] i
n the upper right cerner t
o enter the A
P
configuration page. The app will jump t
o the WiFi connection configuration
page o
f t
h
e mobile phone, press t
h
e host menu k
e
y t
o enter the main page,
and then press the [up / down] k
e
y t
o move the cursor t
o the [LAN), press
the [OK] k
e
y o
r directly press the number k
e
y 171 t
o enter the LA
N page.
Press the number k
e
y [3] t
o enter the A
P network configuration state, and
the Wifi module o
f the host starts t
o distribute a WiFi hotspot. According
t
o the prompt o
n the app page, connect the Wifi hotspot distributed b
y
the host (the name ofthe WiFi hotspot distributed b
y this button:
smarlife-xxxx, n
o password). After connecting the WiFi hotspot o
f the
button, return t
o the app operation page and enter the A
P connection page.
Wl
f
l Settlngs
ln-C0<111QuoQ!IOf1
O.APC0<1ft<l
1 Smor!Coo
2Wlfl-
O.- ¡
n
t
o, !
i
C �
e
tu
,
n
Wl
f
l Se
tn
n
g
s
OAPC
1SmortC0<1
2Wlfl R
e
"'
!
0.-!n.., H
C •
etiJ
,
n
....,..
..;.""""''''
�=11
___.,..,., •
�
...,...,
,...
• • o �
-
.. .¡¡,.
,.
"'
-�-
�I 1
�
J':"
�
1,:
�
,
.
¡
,,
� ...,.,
f • ,. n - l.
�
�
1
J-C
,
_
,.
�
1� lt.�I
- .llÍ
- ,x,..,
l. _J
."'-1,. -·-
�
¡¡
e
,,
_
• '!! -
"l
..,_.. .
, ..�
l.
.
•
r�,,
§.w
-
•
,
,,
AP connection
First connect the mobile phone t
o the h
o
t WiFi emanating fr
o
m the devtce,
and then input the WiFi name and password that the device will b
e
connected t
o
, and then configure the device t
o access the Internet.
WIF1S01tlngs
2
. Press the main menu k
e
y t
o enter the main page, then press the
[up / down] k
e
y t
o move the cursor t
o the [LAN] , press the [OK] k
e
y
o
r directly press the number k
e
y [7] t
o enter the LA
N page. Press the
number k
e
y [2] t
o disconnect the connected WiFi network; Press the
number k
e
y [1] t
o enter the network configuration state.
Note: network access configuration must b
e carried out i
n the same Wifi.
P29 P
30

O
n the app start configuration page, app and equipment are configured.
When the equipment i
s successfully configured, i
t w
ill automatically jump
t
o the [add equipment success] page, and select the name o
f the
equipment, such a
s the living room.
Cllck the "Arm/Disarml" o
f the host o
n the app page t
o enter and operate
the host, and query the operation history.
0
Chapter 6: Receiving Alarms and
Remote Control
6.1 Handing method after receiving alarm:
When there i
s an alarm, the host w
ill automatically dial the telephone
number s
e
t before and alerting according t
o the setting. J
f the phone line
ofthe owner i
s busy o
r cannot b
e connected, the system will dial the next
pre-set number automatically. The system will dial the preset phone
number three times. After receiving the alarm call, i
t will play the preset
recording. The user doesn't need t
o entera password. The following i
s the
corresponding operation when pressing the figures o
n phone:
K
e
y (1]: Arming Key[2]: Disarming
K
e
y [3]: Monitoring O
n Key[4): Monitoring O
ff
K
e
y [S]: Speaker O
n Key[6): Speaker O
ff
K
e
y [7): Siren O
n Key[8): Siren O
ff
K
e
y [9]: Ganged Socket O
n Key[lO]: Ganged Socket O
ff
K
e
y ["']: Exit and hang up. The system would not dial next phone number.
Note: both monitoring and speaking time a
r
e 2
0 seconds. Press (3) k
e
y t
o
continue monitoring. Press [S] t
o continue speaking within 20s.
o-...,.-
,
rn .. ,.,. .
.. ,=·--
o
P31
o
6.2 Remote control operation method
User ca
n use any phone t
o call t
h
e phone number o
f the phone card o
n the
host. After a ringing cycle the host will automatically g
e
t through. After
hearing prompt, enter password (host factory default i
s "1234", there
would b
e a prompt when imputing the wrong password. The system will
automatically hang up i
f the third time i
s still incorrect). Y
o
u will hear a
prompt when password i
s correct. Then, press following keys t
o control
the corresponding functions:
K
e
y [1]: Arming Key[2]: Disarming
K
e
y [3]: Monitoring O
n Key[4): Monitoring O
ff
K
e
y [S]: Speaker O
n Key[6]: Speaker O
ff
K
e
y (7]: Siren O
n Key[8): Siren O
ff
K
e
y [9]: Ganged Socket O
n Key[lO]: Ganged Socket O
ff
K
e
y ["']: Ex
i
t and hang up. The system would not dial next phone number.
P
32

Note: both monitoring a n d s p e a k i n g time are 20 seconds. Press [3] key to
continue monitoring. Press [S] to continue speaking within 20s.
Chapter 7:Technical Parameters
7 .1 Technical Parameters
I n p u t Voltage: USB SV
Standby Current . < 6 0 m A
Alarm Current . <300mA
Wireless F r e q u e n c y : 4 3 3 M H z
GSM Standard : s u p p o r t GSM850/900/1800/1900MHz
W I F I m o d u l e : Support 2.4G wireless W I F I
Backup Battery: 3.7V 800mA Li t h i u m Battery
Standby hours: 8h
Alarm toudness: 80dB
Wireless distance: 100 meters ( i n open area)
7 .2 Factory default zone type
Normal S
T
A
Y Zone lntelligent Help the Senior Doorbell Welcome Emergency
Zone Zone Zone Zone Zone Zone
01-59 Zone 60-79 Zone 80-89 Zone 90 Zone 91 Zone 92 Zone 93-99 Zone
7 .3 System factory default
System Password 1234 SMS Message ON
Remote control ON Remote Alarm ON
A l ertingtime 1 Minute Del ayAl ar m O Seconds
Delay Arm O Seconds 1-99 Zone Alarm Alarm Alerting
1-99 Zone Alarm XX Zone
Message Alarm
P 3 3
Chapter 8 : lnstall Detectors
8 . 1 lnstallation and Usage of Door Sensor
Door sensor is used for sensing the closing a n d o p e n i n g state of the door,
a n d is consisted of transmitter and magnet two parts. lt can be installed
on doors, windows or any object that can be closed a n d o p e n e d . W h e n
transmitter is separated from the magnet, door sensor w i l l send a l a r m
s i g n a l to a l a r m p a n e l , host will a l a r m .
The door contact s h o u l d be installed on the movable door or windows.
Firstly, make the installation position cl e a n . Take out wireless door sensor,
a n d then stick the d o u b l e faced adhesive tape on the bottom. The
installation s h o u l d note the following items:
l.The door sensor part A (transmitter) and part B (magnet) s h o u l d be
installed separately, that is, A on fixed door a n d B o n movable door.
2. A and B s h o u l d be in the s a m e vertical l i n e a n d the distance between A
a n d B s h o u l d not be greater t h a n 1 cm.
3 . After the installation, the indicator light flashes for ls as the door open,
that m e a n s the door sensor is installed successfully.
4. The indicator lighting for 1 second m e a n s a l a r m . The indicator in
constant light is a suggestion of low power.
5 . A, B can a l s o be reinforced by screws, (A: remove the bottom cover,
strengthen the screw a n d then cover the bottom a g a i n ; B can be directly
fixed by the screw.)
P34

8.2 lnstallation and Use of P I R Motion Detector
□
Before use, make sure the power switch of P I R motion sensors is o n .
lnstallation height is about 2 . 2 meters above g ro u n d a n d it s h o u l d be
installed in the corner of the room to get the best detection range. At the
s a m e time, it s h o u l d fo r m a certain a n g l e with the w a l k i n g line (90 degree
angle is best for detection).
l n s t a ll a ti o n :
Talk out the s u p p l i e d bracket; insert the bracket to the slot. Take out the
pedestal a n d fix it with two screws on the wall. Press the P I R with bracket
into the center hole of the pedestal. And t h e n adjust the best angle of
detector. (This method is suitable for project installation)
Attention:
1. The detector s h o u l d not face the outside of window directly.
2. There s h o u l d be no any big objects for obstruction within coverage of
detection.
3. There s h o u l d be no two infrared detectors in the s a m e space as they
will possibly intervene with each other.
4. Avoid facing window, cooling or warming m a c h i n e , stoves, or other
a p p l i a n c e s that cause temperature c h a n g i n g sharply, w h i c h may cause
false a l a r m .
5. lnfrared detector s h o u l d be used indoor only.
P 3 5
Chapter 9:Troubleshooting
Troubleshooting Reasons Methods
1,Nodialing for alarm l. Not arming l. do arming operation
2. alarm phone unset 2.re-set according to the
3.parts improperly installed, instruction book
distance too far 3.adjust the location of parts
4. code not match 4. re-coding
2,Can't remote operate 1, input wrong password 1,Correct password or change
to a new password
3, Host can't read S I M card 1, No SIM card 1, lnsert SIM card
or don't dial and text to 2, PIN code is set for SIM card 2, Cancel PIN code
preset alarm phone 3, bad GSM signal 3, change to a strong signal
number 4, SIM card has scratched copper
place
5, Alarm phone number unset
4, change to a normal SIM card
6, Message Alarm number unset
5, set alarm phone number
7, Card balance is insufficient or
6, set message alarm number
out of date
7, charge SIM card
8, Message function is OFF
8, activate the message function
4, remote controller not 1.coding unmatched with the 1.re-coding
work host 2. change battery of the same
2. insufficient power type
3. battery pieces poor contact or 3. eliminating the dirt on the
corroded pieces caused by corrosion
4. unmatched with host 4. contact the local dealer to
change the matched remote
controller
5, remote controller not 1.coding unmatched with the host 1.re-coding
work 2. insufficient power 2. change battery of the same
3. battery pieces poor contact or type
corroded 3. eliminating the dirt on the
4. unmatched with host pieces caused by corrosion
4. contact the local dealer to
controller
6, PIR sensor not work 1.coding unmatched with the host 1.re-coding
2. insufficient power 2. change battery of the same
3. battery pieces poor contact or type
corroded 3. eliminating the dirt on the
4. unmatched with host pieces caused by corrosion
4. contact the local dealer to
controller
7, no sound from siren l. Siren plug or jack have short 1.Fix or change the plug or jack
circuit or disconnection 2.Change the plug cord
2. Plug cord has open circuit 3.Set siren a l a r m i n g time on
3. Siren is off the host
P36

8, The transmitter distance l. a nearby emitter is sending 1.find the interfering source
for host is shortened signal and eliminate it
2. The host receiver stops work 2.send the host back to the
3. Power supply of stand by factory for repairing
battery of the host is insufficient 3.check whether the power
supply is plugged well
9, Keep alarming when Telephone line is not connected Connect the phone line and
host is on and disconnection alarm function close the disconnection alarm
is open function.
P 3 7 P38

W181 User manual-.pdf

Recommended

Recommended

More Related Content

Similar to W181 User manual-.pdf

Similar to W181 User manual-.pdf (20)

Recently uploaded

Recently uploaded (20)

W181 User manual-.pdf