LCD Display Proteus and mikroC Software. Proteus 8 use hardware simulation and mikcroC use C code.

1. A PRESENTATION ON
DISPLAYING IN LCD USING
PROTEUS

2. GROUP MEMBERS
Name ID
1.Kandil Al Aksa 12131103054
2.Md. Omar Faruq 12131103065
3.Azharul Islam 12131103066

3. OBJECTIVES
To understand how to Display in LCD
How to use PIC-16F877 Micro-controller
How to use LM016L (16 X 2) LCD

4. SOFTWARE COMPONENTS
Proteus 8.0 Professional Simulator
MikroC Pro v-5.61

5. SIMULATING COMPONENTS
• Micro-Controller PIC16F877
• LCD Display (16X2) Model - LM016L
• POT-HG (Variable Resistor)
• GROUND

6. MICRO-CONTROLLER
• What is a microcontroller?
A microcontroller is a compact standalone computer, optimized for
control applications. Entire processor, memory and the I/O
interfaces .So it takes less time to read and write to external devices.

7. FEATURES OF PIC16F877A
• High-performance RISC (Reduced Instruction Set Computing) CPU
• Total 40 Pins , 33 I/O pins & 5 I/O ports.
• Flash memory:14.3KB(8192 words)
• Data SRAM:368 bytes
• Data EEPROM:256 bytes
• Operating speed:20Mhz, 200ns instruction cycle
• Operating voltage:4.0-5.5volts

8. MICRO-CONTROLLER MODEL - PIC16F877

9. REQUIREMENT OF PINS IN THIS
SIMULATION
Pin Name Pin Number I/O/PType
RB0/INT 33 I/O
RB1 34 I/O
RB2 35 I/O
RB3/PGM 36 I/O
RB4 37 I/O
RB5 38 I/O

10. LCD DISPLAY(16X2) LM016L

11. LCD DISPLAY (16X2) LM016L PIN
DESCRIPTION
Pin Number Symbol Function
01 VSS GND
02 VDD + 3V or + 5V
03 VEE + 4.2V for LED Output
04 RS Register Select Signal
05 R/W Read/Write Signal
06 E Enable Signal
07-14 DB0-DB7 Data Bus Line

12. POT-HG VARIABLE RESISTOR
PO T-HG is the only active variable resistor
that allows you to change the resistance
during simulation run-time

13. SIMULATION

14. MIKRO C PRO (5. 6 1 ) FO R PIC
• m ikro C PRO fo r PIC is a full-featured ANSIC co m pile r fo r PIC devices
from Microchip. It is the best solution for developing code for PIC
devices. It features intuitive IDE (Integrated Device Electronics) ,
powerful compiler with advance d o ptim iz atio ns , lots of hardware and
software libraries .

15. INSTALLATION OF MIKROC PRO FOR PIC
• Install this software just like other simple software .

16. CREATING A NEW PROJECT USING MIKROC

17. CLICK NEXT & GO TO THE NEXT STEP

18. SELECT DEVICE NAME ON WHICH YOU
WORK THEN
CLICK NEXT & GO TO THE NEXT STEP

19. CLICK NEXT & GO TO THE NEXT STEP

20. CLICK NEXT & GO TO THE NEXT STEP

21. CLICK FINISH

22. THIS IS YOUR NEW PROJECT FILE

23. CODE IN MIKROC

24. DOUBLE CLICK ON PIC16F877
MICROCONTROLLER THEN SELECT PROJECT
HEX FILE

25. FINALLY

26. THANK YOU 

27. HAVE YOU ANY QUESTIONS ?

28. DROPBOX DOWNLOAD LINK
HTTPS://WWW.DROPBOX.COM/SH/PUGUAI4S7XWM876/AAAQR0FQT4J4OVDEZFOHA-
48A?DL=0