This document describes a major project on an automatic water level pump controller presented by four electrical engineering students. It contains an introduction, working principle, block diagram, list of components, details of the components, applications, advantages, disadvantages, and references. The automatic water level controller uses sensors to detect the water level and control a pump to maintain the water level between an upper and lower threshold. It aims to automatically control water levels and save water.

1. GUIDED BY:
Mr. RAVINDRA KUMAR
RAJKIYA ENGINEERING COLLEGE
AMBEDKARNAGAR-224122
2017-18
PRESENTED BY
UDAY PRATAP PASWAN (1473720044)
SONU YADAV (1573720907)
GORAKH NATH (1373720017
ADITYA RAJ (1573720901)
B. Tech- FINAL YEAR
ELECTRICAL ENGINEERING
A
MAJOR PROJECT
ON
“WATER LEVAL AUTOMATIC PUMP CONTROLLER”

2. CONTENTS
 INTRODUCTION
 WORKING PRINCIPLE
 BLOCK DIAGRAM
COMPONENTS
 DETAILS OF COMPONENTS
 APPLICATIONS
 ADVANTAGES
 DISADVANTAGES
REFERENCE

3. INTRODUCTION
Automatic water pump controller is a series of
functions to control water level.
With a sensor in the short to create the top level and a
detection sensor for detecting long again made for the
lower level.
 Water is used for a variety of purposes for bathing
and cleaning to drinking and cooking.

4. BLOCK DIAGRAM
T/F 909 volt. C 100µF VR
Transistor
Relay
PUMP
Sensor

5. WORKING PRINCIPLE
 This controller setup has three sensors, one in sum and
other in overhead tank.
 When ever the pump sensor is ON the controller has the
power to control the pump. If the sensor is OFF the whole
controller is turned OFF.
 Now let assume that sump is full and overhead tank is
empty. Now both the sensors in the overhead tank is turned
ON .
 The lower sensor latches the AC relay so that the pump
turns ON.

6. The main power switch is ON, the pump is a ON condition.

7. As soon as the water level increases the lower sensor is turned
off but the pump continuous be on.

8. As water reaches the maximum level the upper sensor is also
turned OFF so is it unlatches the AC relay. So that the both
relay is unlatched the pump is turned OFF.

9. The pump is OFF only when the water level reaches
the minimum level. But pump is OFF.

10. The pump is restart only when the water level reaches the
minimum level.

11. COMPONENTS
 PC BOARD - (1).
 POWER SUPPLY (9-0-9 TRANSFORMER) - (1).
 SWITCH - (1).
 LIGHT EMITTING DIODES (LED’s) - (3).
 RESISTORS - (4).
 CAPACITOR. - (3).
 TRANSISTORS - (1).
 VARIABLE RESISTOR - (1).
 RELAY - (2).
 CONNECTING WIRE.

12. DETAILS OF COMPONENTS
2. POWER SUPPLY-
Step down transformer 230V 50 H AC
Input power to 9V Dc output supply.
1. PC BOARD-
A pc board is a construction base for
prototyping of electronics. It is used for
temporary prototyping and experimenting
with circuit diagram.
3. ON OFF SWITCH-
Main Power supply turn on and
turn off

13. 4. LED’s-
A LED is a two-lead semi
conductor light source. It is a p-n junction
diode (Light Emitting Diode).
5. RESISTORS:
Resistor is a passive component
used to control current in a circuit. Its
resistance is given by the ratio of
voltage applied across its terminals to
the current passing through it.

14. 6. CAPACITOR
 The voltage rating on a capacitor the
maximum amount of voltage. that a
capacitor can safely be store.
 The certain size (1µF to 1000µF, etc.)
and certain voltage (10V, 25V, 50V, etc.).
 Capacitors come in different voltage
ratings, so that can supply circuits with
different voltages.
7. TRANSISTORS
A transistor is a semiconductor device
used to amplify and switch electronic
signals and electrical power.
It is composed of semiconductor material
with at least three terminals.

15. 8. VARIABLE RESISTOR
The variable resistor with
has two applications. One is to change
the resistance.
The switch mechanism is used for the
electric contact and non-contact by
on/off operation of the switch.
There are switch mechanism variable
resistors with annular cross-section
which are used for the control of
equipments.

16. 11. CONNECTING WIRES-
Few connecting wires are used for
connection in the circuit.
9. RELAY-
The relay module is a normally open
normally closed digital switch that
control relay capable of switching much
higher voltages and currents than your
standard a 12 V

17. APPLICATIONS
 Automatic Water level Controller can be used in Hotels,
Factories, Homes Apartments, Commercial Complexes,
Drainage, etc.
 It can be used to predict flood .
 Liquid level indicator in the huge containers in the companies.
 Low power consumer.
 Fuel level indicator in vehicles.

18. ADVANTAGES
 Low maintenance.
 Low costs.
 Compact and good design
 Fully Automatic.
 Saves Water.
 Saves energy.
 Increases Pump Life.

19. DISADVANTAGES
 This project may not be able to handle power.
 The components used in this are sensitive and may
damage easily.
 We need to insert the wire in accordance with the level of
water.

20. REFERENCES
www.microchip.com
www.google.com
www.wikipedia.org

21. THANK YOU