Heat shrink cable joints to suit PVC, EPR (BS6883) and XLPE (BS5467) multi-core cables up to 3.3kV - the heat shrink cable joint comprises of adhesive lined connector insulation tubes, heavy duty steel wire armour earth cage, armour support rings and clamps and an outer thick wall adhesive lined heat shrink tube.
SPS Heat Shrink Cable Joints & Cable Terminations - Quality Performance Testing : Shrink Polymer Systems heat shrink cable joints and cable termination kits are tested to BS7888 which incorporates Cenelec Standards HD 628 S1 and 629.1 S2 : 2006, DIN VDE0279 and IEC60502.
Straight and right angled bushing boots from stock suit switchgear and transformer bushings - bushing boots provide high voltage electrical insulation, preventing flashover caused by moisture ingress, industrial contamination, high humidity and rodents.
High Voltage 33kV Bushing Boots (RABK/STBK)
The high voltage bushing diameters on a 33kV switchgear or transformer system are normally in excess of 100mm in diameter so a standard boot is unsuitable. 33kV insulating boots are ex stock.
Heat shrink cable joints to suit PVC, EPR (BS6883) and XLPE (BS5467) multi-core cables up to 3.3kV - the heat shrink cable joint comprises of adhesive lined connector insulation tubes, heavy duty steel wire armour earth cage, armour support rings and clamps and an outer thick wall adhesive lined heat shrink tube.
SPS Heat Shrink Cable Joints & Cable Terminations - Quality Performance Testing : Shrink Polymer Systems heat shrink cable joints and cable termination kits are tested to BS7888 which incorporates Cenelec Standards HD 628 S1 and 629.1 S2 : 2006, DIN VDE0279 and IEC60502.
Straight and right angled bushing boots from stock suit switchgear and transformer bushings - bushing boots provide high voltage electrical insulation, preventing flashover caused by moisture ingress, industrial contamination, high humidity and rodents.
High Voltage 33kV Bushing Boots (RABK/STBK)
The high voltage bushing diameters on a 33kV switchgear or transformer system are normally in excess of 100mm in diameter so a standard boot is unsuitable. 33kV insulating boots are ex stock.
400 Series Interface C Compact Nexans Euromold Cable Connectors and Bushings connect and terminate HV cables to Interface C bushings on switchgear and transformers.
Nexans Euromold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F.
Nexans Euromold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
400 Series Interface B Nexans Euromold Cable Connectors and Bushings connect and terminate HV cables to Interface B bushings on switchgear and transformers.
Nexans Euromold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F.
Nexans Euromold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
Nuhas is the first and only cable producer in the Middle East to have been certified by DNV, Norway as capable of manufacturing power, control and instrumentation cables for shipboard, high speed/light craft and off-shore cables.
Craig and Derricott Isolators
Isolation Equipment and Switch Disconnectors
Moulded Plastic Isolators & Switch Disconnectors IP65 20A-63A
Mild Steel Isolators & Switch Disconnectors IP65 20A-63A
Stainless Steel Isolators & Switch Disconnectors IP65 20A-63A
Die Cast Isolators & Switch Disconnectors IP65 20A-63A
Sheet Steel Isolators & Switch Disconnectors IP41 32A-630A
Sheet Steel Isolators & Switch Disconnectors IP65 32A-1000A
ATEX Zone 22 Isolators& Switch Disconnectors Cat 3D
Fire Rated Isolators & Switch Disconnectors 20A-125A
Isolation Equipment and Switch Disconnectors
Craig & Derricott Section 12 London Underground Isolators
Craig & Derricott Stainless Steel Water Utility Isolators
Lucy Lighting Street Lighting Trojan Isolators
Switch Disconnectors (Isolators) provide the means to safely disconnect or isolate an item of electrical equipment from the power supply - primarily designed to provide a means of local isolation when an elecrical item may need maintenance or repair. Switch Disconnectors also i) provide an effective clearance between the supply and the electrical load appropriate to the voltage applied, ii) provide a means of "locking off" (padlocking), iii) provide true indication of contact state, iv) provide a safe electrical disconnection from the power supply even under fault conditions.
Euromold Connectors 400 Series Interface Type B Bushing
* Connector Type : 14mm Plug-In Pin Contact
* Voltage Range : 11/12kV-33/36kV
* Current Rating : 400amps
* Specification : CENELEC EN50180 & EN50181
Euromold 400LR Elbow Connectors are used with 400 Series Interface B Bushing.
Hazardous Area Isolators
ATEX Isolators - Zone 22 Category 3D Isolators
Craig & Derricott ATEX certified isolators and switch disconnectors for hazardous area Group II, Zone 22, Cat 3D Non-Conductive Dusts - typical installation areas include grain mills, textiles, cargo handling, powder coating plant, chemicals, woodworking and waste processing.
From July 2006 the onus was placed upon companies to ensure that all electrical equipment within their site organisation is suitable for the environment in which it is being used - this was aimed particularly at hazardous areas where there may be a possibility of a combustible atmosphere being present, even for short periods i.e. less than 10 hours/year.
People normally think of such atmospheres as being gases, mists or vapours - however there are various industries where a conductive or non-conductive dust mixed with air in the right proportion can become explosive.
There are different degrees of protection against explosive dusts and hazardous area Zone 22 is defined as : - "a place in which an explosive atmosphere, in the form of a cloud of combustible dust in air, is not likely to occur in normal operation but, if it does occur, will persist for a short period only".
ATEX Directive 94/9/EC sets out the route electrical equipment manufacturers must take to get their products certified for use in hazardous areas.
ATEX Certified Electrical Equipment for Hazardous Areas
ATEX is the name given to a set of European Directives relating to Hazardous Area Electrical Equipment Installations (Flammable Atmospheres) to avoid industrial accident or incident. ATEX Directive 94/9/EC (ATEX 95), is a directive adopted by the EU under the “New Approach” strategy. The “New Approach” ATEX directive supersedes the “Old Approach” ATEX Directive, the Potentially Explosive Atmospheres Directive, 76/117/EEC – ATEX 94/9/EC (ATEX 95) facilitates free trade in the EC for hazardous area electrical equipment intended to be used in potentially explosive atmospheres. ATEX Directive 94/9/EC (ATEX 95) covers “Electrical Equipment” used in hazardous areas with potentially explosive atmospheres created by presence of gases, vapours, mists or dusts.
Prysmian Group/Draka is world leader in the energy and telecom cables and systems industry. With sales ofsome €8 billion in 2012, more than 20,000 employees across 50 countries and 91 plants , the Group is strongly positioned in high-tech markets and offers the widest range of products, services, technologies and know-how
Prysmian Cables & Systems is the UK's largest domestic manufacturer of energy and telecommunications cables and systems to service home and export markets.
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Euromold elbow connectors, Euromold tee connectors, Euromold bushings (oil insulated) and Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series, 400TB 440TB Features :
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
T&D UK with the support of Nexans provide installation training and certification for experienced high voltage cable jointers up to 33kV.
Datwyler universal safety fire fiber cabel info tech middle eastAli Shoaee
Datwyler Universal Fiber Optic Fire Safety cable E30 - 30 minutes System Circuit Integrity ..
Metal-free, water resistant, rodent protection,
in accordance with IEC 60332.1 and IEC 60332.3 C
30 minutes System Circuit Integrity according to DIN 4102-12
Application :
Safety applications in tunnels, underground railways, banks, insurance companies, large-scale industry , Public Area , Mall , Towers .
Fiber optic LAN backbone.
Indoor and outdoor cabling.
Can be installed in cable platforms, trays, ducts and vertical shafts.
Can be spliced in FO distributors.
Zero halogen, no corrosive gases :
IEC 60754-1/-2, EN 60754-1/-2, VDE 0482-754-1/-2
Flame propagation:
IEC 60332-1/-2, EN 60332-1-2, VDE 0482-332-1-2
Flame spread:
IEC 60332.3 C, EN 50266-2-4, VDE 0482-266-2-4
Smoke density:
IEC 61034-1/-2, EN 61034-1/-2 (EN 50268-1/-2), VDE 0482-1034-1/-2 (VDE 0482-268-1/-2)
Circuit Integrity (FE180):
IEC 60331-11, IEC 60331-25, VDE 0472 part 814, EN 50200 PH 90, EN 50362, VDE 0482-200, VDE 0482-362:
System circuit integrity
according to DIN 4102 part 12, VKF Fire Safety Application No. 24176
Please Contact Info Tech Middle East for more Detail : Info@InfoTechME.ws
400 Series Interface C Compact Nexans Euromold Cable Connectors and Bushings connect and terminate HV cables to Interface C bushings on switchgear and transformers.
Nexans Euromold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F.
Nexans Euromold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
400 Series Interface B Nexans Euromold Cable Connectors and Bushings connect and terminate HV cables to Interface B bushings on switchgear and transformers.
Nexans Euromold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F.
Nexans Euromold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
Nuhas is the first and only cable producer in the Middle East to have been certified by DNV, Norway as capable of manufacturing power, control and instrumentation cables for shipboard, high speed/light craft and off-shore cables.
Craig and Derricott Isolators
Isolation Equipment and Switch Disconnectors
Moulded Plastic Isolators & Switch Disconnectors IP65 20A-63A
Mild Steel Isolators & Switch Disconnectors IP65 20A-63A
Stainless Steel Isolators & Switch Disconnectors IP65 20A-63A
Die Cast Isolators & Switch Disconnectors IP65 20A-63A
Sheet Steel Isolators & Switch Disconnectors IP41 32A-630A
Sheet Steel Isolators & Switch Disconnectors IP65 32A-1000A
ATEX Zone 22 Isolators& Switch Disconnectors Cat 3D
Fire Rated Isolators & Switch Disconnectors 20A-125A
Isolation Equipment and Switch Disconnectors
Craig & Derricott Section 12 London Underground Isolators
Craig & Derricott Stainless Steel Water Utility Isolators
Lucy Lighting Street Lighting Trojan Isolators
Switch Disconnectors (Isolators) provide the means to safely disconnect or isolate an item of electrical equipment from the power supply - primarily designed to provide a means of local isolation when an elecrical item may need maintenance or repair. Switch Disconnectors also i) provide an effective clearance between the supply and the electrical load appropriate to the voltage applied, ii) provide a means of "locking off" (padlocking), iii) provide true indication of contact state, iv) provide a safe electrical disconnection from the power supply even under fault conditions.
Euromold Connectors 400 Series Interface Type B Bushing
* Connector Type : 14mm Plug-In Pin Contact
* Voltage Range : 11/12kV-33/36kV
* Current Rating : 400amps
* Specification : CENELEC EN50180 & EN50181
Euromold 400LR Elbow Connectors are used with 400 Series Interface B Bushing.
Hazardous Area Isolators
ATEX Isolators - Zone 22 Category 3D Isolators
Craig & Derricott ATEX certified isolators and switch disconnectors for hazardous area Group II, Zone 22, Cat 3D Non-Conductive Dusts - typical installation areas include grain mills, textiles, cargo handling, powder coating plant, chemicals, woodworking and waste processing.
From July 2006 the onus was placed upon companies to ensure that all electrical equipment within their site organisation is suitable for the environment in which it is being used - this was aimed particularly at hazardous areas where there may be a possibility of a combustible atmosphere being present, even for short periods i.e. less than 10 hours/year.
People normally think of such atmospheres as being gases, mists or vapours - however there are various industries where a conductive or non-conductive dust mixed with air in the right proportion can become explosive.
There are different degrees of protection against explosive dusts and hazardous area Zone 22 is defined as : - "a place in which an explosive atmosphere, in the form of a cloud of combustible dust in air, is not likely to occur in normal operation but, if it does occur, will persist for a short period only".
ATEX Directive 94/9/EC sets out the route electrical equipment manufacturers must take to get their products certified for use in hazardous areas.
ATEX Certified Electrical Equipment for Hazardous Areas
ATEX is the name given to a set of European Directives relating to Hazardous Area Electrical Equipment Installations (Flammable Atmospheres) to avoid industrial accident or incident. ATEX Directive 94/9/EC (ATEX 95), is a directive adopted by the EU under the “New Approach” strategy. The “New Approach” ATEX directive supersedes the “Old Approach” ATEX Directive, the Potentially Explosive Atmospheres Directive, 76/117/EEC – ATEX 94/9/EC (ATEX 95) facilitates free trade in the EC for hazardous area electrical equipment intended to be used in potentially explosive atmospheres. ATEX Directive 94/9/EC (ATEX 95) covers “Electrical Equipment” used in hazardous areas with potentially explosive atmospheres created by presence of gases, vapours, mists or dusts.
Prysmian Group/Draka is world leader in the energy and telecom cables and systems industry. With sales ofsome €8 billion in 2012, more than 20,000 employees across 50 countries and 91 plants , the Group is strongly positioned in high-tech markets and offers the widest range of products, services, technologies and know-how
Prysmian Cables & Systems is the UK's largest domestic manufacturer of energy and telecommunications cables and systems to service home and export markets.
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Nexans Euromold elbow connectors, Nexans Euromold tee connectors, Nexans Euromold bushings (oil insulated) and Nexans Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series
Euromold 400LB Elbow Connectors & 400TB 440TB Elbow Connectors
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
Nexans Euromold 400 series screened separable connectors are EPDM pre-moulded,high voltage cable terminations for 6.6kV, 11kV, 15kV, 24kV and 33kV electrical equipment including switchgear, transformers and motors.
Nexans Euromold 400 series separable connectors include Euromold elbow connectors, Euromold tee connectors, Euromold bushings (oil insulated) and Euromold surge arresters to protect electrical equipment up to 33kV.
Nexans Euromold Separable Elbow Connectors 400 Series, 400TB 440TB Features :
Connector for terminating high voltage polymeric (XLPE EPR) cables, 11-33kV
Plug in bolted tee connectors with current rating 630amps and 1250amps
Conductive EPDM jacket provides a touch safe screened termination
Suits copper wire and copper tape screened cable, 35-300sqmm
Type C 630A interface to CENELEC EN50180
T&D UK with the support of Nexans provide installation training and certification for experienced high voltage cable jointers up to 33kV.
Datwyler universal safety fire fiber cabel info tech middle eastAli Shoaee
Datwyler Universal Fiber Optic Fire Safety cable E30 - 30 minutes System Circuit Integrity ..
Metal-free, water resistant, rodent protection,
in accordance with IEC 60332.1 and IEC 60332.3 C
30 minutes System Circuit Integrity according to DIN 4102-12
Application :
Safety applications in tunnels, underground railways, banks, insurance companies, large-scale industry , Public Area , Mall , Towers .
Fiber optic LAN backbone.
Indoor and outdoor cabling.
Can be installed in cable platforms, trays, ducts and vertical shafts.
Can be spliced in FO distributors.
Zero halogen, no corrosive gases :
IEC 60754-1/-2, EN 60754-1/-2, VDE 0482-754-1/-2
Flame propagation:
IEC 60332-1/-2, EN 60332-1-2, VDE 0482-332-1-2
Flame spread:
IEC 60332.3 C, EN 50266-2-4, VDE 0482-266-2-4
Smoke density:
IEC 61034-1/-2, EN 61034-1/-2 (EN 50268-1/-2), VDE 0482-1034-1/-2 (VDE 0482-268-1/-2)
Circuit Integrity (FE180):
IEC 60331-11, IEC 60331-25, VDE 0472 part 814, EN 50200 PH 90, EN 50362, VDE 0482-200, VDE 0482-362:
System circuit integrity
according to DIN 4102 part 12, VKF Fire Safety Application No. 24176
Please Contact Info Tech Middle East for more Detail : Info@InfoTechME.ws
Datwyler CU 662 4P CAT6 240136
Data cable, U/UTP, Category 6, AWG24
1 Inner conductor: AWG24/0,55 mm Bare Copper wire
2 PE insulated conductor: 0.98 mm ∅ PE
3 Pair seperator
4 Outer sheath: FRNC/LSoH orange RAL 2003, FR/PVC grey RAL 7037
Description
Electrically and mechanically advanced quality Cat.6 data cable - fulfils the requirements of ISO/IEC 11801, IEC 61156-5, EN 50173-1 and EN 50288-6-1.
Robust cable design with reliable electrical performance thanks to stabilising element.
Very good NEXT reserve due to cable construction with a pair separator (cross).
Compatible with all current connecting hardware in accordance with EN 50173 and ISO/IEC 11801.
Data cable for structured premesis cabling.
For the transmission of digital and analogue voice, video and data signals.
Suitable for all ICT network applications up to class E applications (250 MHz) in accordance with EN 50173-1 and ISO/IEC 11801.
Applicable for Power over Ethernet (PoE) / PoE+.
Wire colour
white - blue/blue white - orange/orange white - green/green white - brown/brown in accordance with IEC 60189 and IEC 60708 (ring marked)
Imprint
DATWYLER «cable type» «additional text» «batch number» «meter marks»
Zero halogen, no corrosive gases
IEC 60754-1/-2, EN 50267-2-1/-2-2, VDE 0482-267-2-1/-2-2, AREI-RGIE Art.104-SA - applies to FRNC/LSOH
Flame propagation
IEC 60332-1/-2, EN 60332-1-2, VDE 0482-332-1-2, AREI-RGIE Art.104-F1
Smoke density
IEC 61034-1/-2, EN 61034-1/-2, VDE 0482-1034-1/-2, AREI-RGIE Art.104-SD - applies to FRNC/LSOH
PoE
IEEE 802.3af
Segregation class
b
Cat./Class
Cat 6 / Class E - limit values as specified by IEC 61156-5 and EN 50288-6-1 guaranteed
Euromold Connectors 400 Series Interface Type C Bushing - 630Amp
* Connector Type : M16 Bolted Copper Insert
* Voltage Range : 11/12kV-33/36kV
* Current Rating : 630amps
* Specification : CENELEC EN50180 & EN50181
Euromold 430TB Elbow Connectors are used with 400 Series Interface C Bushing.
Nexans Euromold tee connectors are designed for terminating high voltage XLPE power cables into compact switchgear to make optimum use of limited installation space.
Nexans, the worldwide leader in the cable industry, has extended its well-proven range of compact high voltage (HV) connectors with two new tee-shaped connectors designed specifically for use with compact switchgear and transformers now being specified for wind turbine applications. The Nexans Euromold M430TB connector is for use with higher voltages (up to 33-36kV) and the M434TB connector is for higher currents (up to 1,250 A).
Trend Towards Compact Switchgear for Wind Turbines
The growing trend towards using ever more compact high voltage switchgear in wind turbines has resulted in smaller cable boxes, limiting the space available for connectors. Nexans has responded to this challenge by developing its new asymmetric tee-shape connectors to create a compact connection solution. This now enables two cables to be connected in the same space required for one cable using a traditional non-compact connector. As well as being ideal for all applications where space is a limiting factor, the Nexans compact connectors also enable users to increase the capacity of an existing installation.
EPDM Jacket: A Key Design Feature for Safety and Reliability
The Nexans Euromold M430TB and the M434TB are separable tee-shape bolted connectors designed to connect high voltage polymer-insulated cable to wind turbine equipment such as switchgear and transformers- they can also be used for cable to cable connections with the appropriate mating parts. A key design feature is the thick (3 mm) EPDM (Ethylene Propylene Diene Monomer) rubber conductive insulation jacket that provides a total safe to touch screen for personnel safety, this is both more reliable and longer lasting than the painted silicone rubber insulation used in many connectors.
400 Series Interface C Compact Nexans Euromold Cable Connectors and Bushings connect and terminate HV cables to Interface C bushings on switchgear and transformers.
Nexans Euromold provide high voltage cable accessories to suit the 7 main bushing interfaces : A, B, C (Compact), C (Symmetrical), D, E and F.
Nexans Euromold cable joints, cable terminations, epoxy bushings, angled (elbow) and straight plug-in or bolted separable connectors for connecting, jointing and terminating high voltage cables.
The Nexans Euromold compact version screened separable connector is suitable for high voltage HV cable termination up to 33kV. Interface Type C Euromold M16 bolted tee connectors up to 33kV are designed to connect and terminate polymeric (XLPE EPR) cables to M16 bolted 400 series equipment bushings. Nexans Euromold connectors are supplied in sets of three phases.
Nexans Euromold Kit Contents: 3 x connector housings, 3 x size sensitive cable reducers, 3 x conductor contact lug, 3 x clamping screws and 3 x insulating plugs & caps.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
1. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 1 / 25
Feed-through terminal block - UT 4 - 3044102
Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's
documentation. Our General Terms of Use for Downloads are valid
(http://phoenixcontact.com/download)
Feed-through terminal block, connection method: Screw connection, number of connections: 2, cross
section:0.14 mm² - 6 mm², AWG: 26 - 10, width: 6.2 mm, height: 46.9 mm, color: gray, mounting type: NS 35/7,5,
NS 35/15
Why buy this product
The large wiring space enables the connection of solid and stranded conductors without ferrules, even above the nominal cross section
As well as saving space, the compact design enables user-friendly wiring in a small amount of space
Optimum screwdriver guidance through closed screw shafts
Tested for railway applications
The cable entry funnel enables the use of conductors with ferrules and plastic collars within the nominal cross section
Key Commercial Data
Packing unit 1 STK
Minimum order quantity 50 STK
GTIN
GTIN 4017918960391
Weight per Piece (excluding packing) 9.600 g
Custom tariff number 85369010
Country of origin Germany
Technical data
General
Number of levels 1
Number of connections 2
Potentials 1
2. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 2 / 25
Feed-through terminal block - UT 4 - 3044102
Technical data
General
Nominal cross section 4 mm²
Color gray
Insulating material PA
Flammability rating according to UL 94 V0
Area of application Railway industry
Machine building
Plant engineering
Process industry
Rated surge voltage 8 kV
Degree of pollution 3
Overvoltage category III
Insulating material group I
Maximum power dissipation for nominal condition 1.02 W
Maximum load current 41 A (with 6 mm² conductor cross section)
Nominal current IN 32 A (with 4 mm² conductor cross section)
Nominal voltage UN 1000 V
Open side panel Yes
Shock protection test specification DIN EN 50274 (VDE 0660-514):2002-11
Back of the hand protection guaranteed
Finger protection guaranteed
Result of surge voltage test Test passed
Surge voltage test setpoint 9.8 kV
Result of power-frequency withstand voltage test Test passed
Power frequency withstand voltage setpoint 2.2 kV
Result of the test for mechanical stability of terminal points (5 x conductor
connection)
Test passed
Result of bending test Test passed
Bending test rotation speed 10 rpm
Bending test turns 135
Bending test conductor cross section/weight 0.14 mm² / 0.2 kg
4 mm² / 0.9 kg
6 mm
2
/ 1.4 kg
Tensile test result Test passed
Conductor cross section tensile test 0.14 mm²
Tractive force setpoint 10 N
Conductor cross section tensile test 4 mm²
Tractive force setpoint 60 N
3. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 3 / 25
Feed-through terminal block - UT 4 - 3044102
Technical data
General
Conductor cross section tensile test 6 mm²
Tractive force setpoint 80 N
Result of tight fit on support Test passed
Tight fit on carrier NS 35
Setpoint 1 N
Result of voltage-drop test Test passed
Requirements, voltage drop ≤ 3.2 mV
Result of temperature-rise test Test passed
Short circuit stability result Test passed
Conductor cross section short circuit testing 4 mm²
Short-time current 0.48 kA
Conductor cross section short circuit testing 6 mm²
Short-time current 0.72 kA
Result of thermal test Test passed
Proof of thermal characteristics (needle flame) effective duration 30 s
Oscillation, broadband noise test result Test passed
Test specification, oscillation, broadband noise DIN EN 50155 (VDE 0115-200):2008-03
Test spectrum Service life test category 1, class B, body mounted
Test frequency f1 = 5 Hz to f2 = 150 Hz
ASD level 1.857 (m/s
2
)
2
/Hz
Acceleration 0,8 g
Test duration per axis 5 h
Test directions X-, Y- and Z-axis
Shock test result Test passed
Test specification, shock test DIN EN 50155 (VDE 0115-200):2008-03
Shock form Half-sine
Acceleration 5 g
Shock duration 30 ms
Number of shocks per direction 3
Test directions X-, Y- and Z-axis (pos. and neg.)
Relative insulation material temperature index (Elec., UL 746 B) 130 °C
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21)) 125 °C
Static insulating material application in cold -60 °C
Behavior in fire for rail vehicles (DIN 5510-2) Test passed
Flame test method (DIN EN 60695-11-10) V0
Oxygen index (DIN EN ISO 4589-2) >32 %
NF F16-101, NF F10-102 Class I 2
4. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 4 / 25
Feed-through terminal block - UT 4 - 3044102
Technical data
General
NF F16-101, NF F10-102 Class F 2
Surface flammability NFPA 130 (ASTM E 162) passed
Specific optical density of smoke NFPA 130 (ASTM E 662) passed
Smoke gas toxicity NFPA 130 (SMP 800C) passed
Calorimetric heat release NFPA 130 (ASTM E 1354) 27,5 MJ/kg
Fire protection for rail vehicles (DIN EN 45545-2) R22 HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R23 HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R24 HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R26 HL 1 - HL 3
Dimensions
Width 6.2 mm
End cover width 2.2 mm
Length 47.7 mm
Height 46.9 mm
Height NS 35/7,5 47.5 mm
Height NS 35/15 55 mm
Connection data
Connection method Screw connection
Connection in acc. with standard IEC 60947-7-1
Note
Note: Product releases, connection cross sections and notes on
connecting aluminum cables can be found in the download area.
Conductor cross section solid min. 0.14 mm²
Conductor cross section solid max. 6 mm²
Conductor cross section AWG min. 26
Conductor cross section AWG max. 10
Conductor cross section flexible min. 0.14 mm²
Conductor cross section flexible max. 6 mm²
Min. AWG conductor cross section, flexible 26
Max. AWG conductor cross section, flexible 10
Conductor cross section flexible, with ferrule without plastic sleeve min. 0.14 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max. 4 mm²
Conductor cross section flexible, with ferrule with plastic sleeve min. 0.14 mm²
Conductor cross section flexible, with ferrule with plastic sleeve max. 4 mm²
2 conductors with same cross section, solid min. 0.14 mm²
2 conductors with same cross section, solid max. 1.5 mm²
2 conductors with same cross section, stranded min. 0.14 mm²
2 conductors with same cross section, stranded max. 1.5 mm²
5. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 5 / 25
Feed-through terminal block - UT 4 - 3044102
Technical data
Connection data
2 conductors with same cross section, stranded, TWIN ferrules with plastic
sleeve, min.
0.5 mm²
2 conductors with same cross section, stranded, TWIN ferrules with plastic
sleeve, max.
2.5 mm²
2 conductors with same cross section, stranded, ferrules without plastic
sleeve, min.
0.14 mm²
2 conductors with same cross section, stranded, ferrules without plastic
sleeve, max.
1.5 mm²
Connection in acc. with standard IEC/EN 60079-7
Conductor cross section solid min. 0.14 mm²
Conductor cross section solid max. 6 mm²
Conductor cross section AWG min. 26
Conductor cross section AWG max. 10
Conductor cross section flexible min. 0.14 mm²
Conductor cross section flexible max. 4 mm²
Stripping length 9 mm
Internal cylindrical gage A4
Screw thread M3
Tightening torque, min 0.6 Nm
Tightening torque max 0.8 Nm
Standards and Regulations
Connection in acc. with standard CSA
IEC 60947-7-1
Flammability rating according to UL 94 V0
Fire protection for rail vehicles (DIN EN 45545-2) R22 HL 1 - HL 3 HL 1 - HL 3 HL 1 - HL 3 HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R23 HL 1 - HL 3 HL 1 - HL 3 HL 1 - HL 3 HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R24 HL 1 - HL 3 HL 1 - HL 3 HL 1 - HL 3 HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R26 HL 1 - HL 3 HL 1 - HL 3 HL 1 - HL 3 HL 1 - HL 3
Environmental Product Compliance
China RoHS Environmentally Friendly Use Period = 50
For details about hazardous substances go to tab “Downloads”, Category
“Manufacturer's declaration”
Drawings
Circuit diagram
7. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 7 / 25
Feed-through terminal block - UT 4 - 3044102
Approvals
CSA
http://www.csagroup.org/services-industries/product-listing/ 13631
B C
mm²/AWG/kcmil 26-10 26-10
Nominal current IN 30 A 30 A
Nominal voltage UN 600 V 600 V
UL Recognized
http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm FILE E 60425
B C
mm²/AWG/kcmil 26-10 26-10
Nominal current IN 30 A 30 A
Nominal voltage UN 600 V 600 V
VDE Gutachten mit
Fertigungsüberwachung
http://www.vde.com/en/Institute/OnlineService/
VDE-approved-products/Pages/Online-Search.aspx
40013658
mm²/AWG/kcmil 0.2-4
Nominal voltage UN 800 V
cUL Recognized
http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm FILE E 60425
B C
mm²/AWG/kcmil 26-10 26-10
Nominal current IN 30 A 30 A
Nominal voltage UN 600 V 600 V
LR
http://www.lr.org/en 05/20042
RS
http://www.rs-head.spb.ru/en/index.php 11.04057.250
8. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 8 / 25
Feed-through terminal block - UT 4 - 3044102
Approvals
IECEE CB Scheme
http://www.iecee.org/ DE1-50905
mm²/AWG/kcmil 0.2-4
Nominal voltage UN 800 V
EAC
EAC-Zulassung
EAC
7500651.22.01.00246
DNV GL http://exchange.dnv.com/tari/ TAE00001S9
PRS
http://www.prs.pl/ TE/2156/880590/17
cULus Recognized
http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm
Accessories
Accessories
DIN rail
DIN rail perforated - NS 35/ 7,5 PERF 2000MM - 0801733
DIN rail perforated, Width: 35 mm, Height: 7.5 mm, In acc. with EN 60715: 2001, Material: Steel, Galvanized, passivated
with a thick layer, Length: 2000 mm
9. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 9 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
DIN rail, unperforated - NS 35/ 7,5 UNPERF 2000MM - 0801681
DIN rail, unperforated, Width: 35 mm, Height: 7.5 mm, In acc. with EN 60715: 2001, Material: Steel, Galvanized,
passivated with a thick layer, Length: 2000 mm
DIN rail perforated - NS 35/ 7,5 WH PERF 2000MM - 1204119
DIN rail perforated, Width: 35 mm, Height: 7.5 mm, In acc. with EN 60715: 2001, Material: Steel, Galvanized, white
passivated, Length: 2000 mm
DIN rail, unperforated - NS 35/ 7,5 WH UNPERF 2000MM - 1204122
DIN rail, unperforated, Width: 35 mm, Height: 7.5 mm, In acc. with EN 60715: 2001, Material: Steel, Galvanized, white
passivated, Length: 2000 mm
DIN rail, unperforated - NS 35/ 7,5 AL UNPERF 2000MM - 0801704
DIN rail, unperforated, Width: 35 mm, Height: 7.5 mm, In acc. with EN 60715: 2001, Material: Aluminum, uncoated,
Length: 2000 mm
DIN rail perforated - NS 35/ 7,5 ZN PERF 2000MM - 1206421
DIN rail perforated, Width: 35 mm, Height: 7.5 mm, In acc. with EN 60715: 2001, Material: Steel, Galvanized,
Length: 2000 mm
10. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 10 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
DIN rail, unperforated - NS 35/ 7,5 ZN UNPERF 2000MM - 1206434
DIN rail, unperforated, Width: 35 mm, Height: 7.5 mm, In acc. with EN 60715: 2001, Material: Steel, Galvanized,
Length: 2000 mm
DIN rail, unperforated - NS 35/ 7,5 CU UNPERF 2000MM - 0801762
DIN rail, unperforated, Width: 35 mm, Height: 7.5 mm, In acc. with EN 60715: 2001, Material: Copper, uncoated,
Length: 2000 mm
End cap - NS 35/ 7,5 CAP - 1206560
DIN rail end piece, for DIN rail NS 35/7.5
DIN rail perforated - NS 35/15 PERF 2000MM - 1201730
DIN rail perforated, Width: 35 mm, Height: 15 mm, In acc. with EN 60715: 2001, Material: Steel, Galvanized, passivated
with a thick layer, Length: 2000 mm
DIN rail, unperforated - NS 35/15 UNPERF 2000MM - 1201714
DIN rail, unperforated, Width: 35 mm, Height: 15 mm, In acc. with EN 60715: 2001, Material: Steel, Galvanized,
passivated with a thick layer, Length: 2000 mm
11. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 11 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
DIN rail perforated - NS 35/15 WH PERF 2000MM - 0806602
DIN rail perforated, Width: 35 mm, Height: 15 mm, In acc. with EN 60715: 2001, Material: Steel, Galvanized, white
passivated, Length: 2000 mm
DIN rail, unperforated - NS 35/15 WH UNPERF 2000MM - 1204135
DIN rail, unperforated, Width: 35 mm, Height: 15 mm, In acc. with EN 60715: 2001, Material: Steel, Galvanized, white
passivated, Length: 2000 mm
DIN rail, unperforated - NS 35/15 AL UNPERF 2000MM - 1201756
DIN rail, unperforated, Width: 35 mm, Height: 15 mm, Similar to EN 60715: 2001, Material: Aluminum, uncoated,
Length: 2000 mm
DIN rail perforated - NS 35/15 ZN PERF 2000MM - 1206599
DIN rail perforated, Width: 35 mm, Height: 15 mm, Similar to EN 60715: 2001, Material: Steel, Galvanized, Length: 2000
mm
DIN rail, unperforated - NS 35/15 ZN UNPERF 2000MM - 1206586
DIN rail, unperforated, Width: 35 mm, Height: 15 mm, Similar to EN 60715: 2001, Material: Steel, Galvanized,
Length: 2000 mm
12. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 12 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
DIN rail, unperforated - NS 35/15 CU UNPERF 2000MM - 1201895
DIN rail, unperforated, Width: 35 mm, Height: 15 mm, Similar to EN 60715: 2001, Material: Copper, uncoated,
Length: 2000 mm
End cap - NS 35/15 CAP - 1206573
DIN rail end piece, for DIN rail NS 35/15
DIN rail, unperforated - NS 35/15-2,3 UNPERF 2000MM - 1201798
DIN rail, unperforated, Width: 35 mm, Height: 15 mm, In acc. with EN 60715: 2001, Material: Steel, Galvanized,
passivated with a thick layer, Length: 2000 mm
End block
End clamp - CLIPFIX 35 - 3022218
Quick mounting end clamp for NS 35/7,5 DIN rail or NS 35/15 DIN rail, with marking option, width: 9.5 mm, color: gray
End clamp - CLIPFIX 35-5 - 3022276
Quick mounting end clamp for NS 35/7,5 DIN rail or NS 35/15 DIN rail, with marking option, with parking option for
FBS...5, FBS...6, KSS 5, KSS 6, width: 5.15 mm, color: gray
13. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 13 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
End clamp - E/NS 35 N - 0800886
End clamp, width: 9.5 mm, color: gray
End cover
End cover - D-UT 2,5/10 - 3047028
End cover, length: 47 mm, width: 2.2 mm, height: 39.8 mm, color: gray
Insulating sleeve
Insulating sleeve - MPS-IH WH - 0201663
Insulating sleeve, color: white
Insulating sleeve - MPS-IH RD - 0201676
Insulating sleeve, color: red
Insulating sleeve - MPS-IH BU - 0201689
Insulating sleeve, color: blue
14. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 14 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
Insulating sleeve - MPS-IH YE - 0201692
Insulating sleeve, color: yellow
Insulating sleeve - MPS-IH GN - 0201702
Insulating sleeve, color: green
Insulating sleeve - MPS-IH GY - 0201728
Insulating sleeve, color: gray
Insulating sleeve - MPS-IH BK - 0201731
Insulating sleeve, color: black
Jumper
Plug-in bridge - FBS 2-6 - 3030336
Plug-in bridge, pitch: 6.2 mm, width: 10.7 mm, number of positions: 2, color: red
15. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 15 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
Plug-in bridge - FBS 3-6 - 3030242
Plug-in bridge, pitch: 6.2 mm, width: 16.9 mm, number of positions: 3, color: red
Plug-in bridge - FBS 4-6 - 3030255
Plug-in bridge, pitch: 6.2 mm, width: 23.1 mm, number of positions: 4, color: red
Plug-in bridge - FBS 5-6 - 3030349
Plug-in bridge, pitch: 6.2 mm, width: 29.3 mm, number of positions: 5, color: red
Plug-in bridge - FBS 6-6 - 1008238
Plug-in bridge, pitch: 6.2 mm, width: 35.5 mm, number of positions: 6, color: red
Plug-in bridge - FBS 10-6 - 3030271
Plug-in bridge, pitch: 6.2 mm, width: 60.3 mm, number of positions: 10, color: red
16. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 16 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
Plug-in bridge - FBS 20-6 - 3030365
Plug-in bridge, pitch: 6.2 mm, width: 122.3 mm, number of positions: 20, color: red
Plug-in bridge - FBS 50-6 - 3032224
Plug-in bridge, pitch: 6.2 mm, width: 308.3 mm, number of positions: 50, color: red
Plug-in bridge - FBSR 2-6 - 3033715
Plug-in bridge, pitch: 6.2 mm, number of positions: 2, color: red
Plug-in bridge - FBSR 3-6 - 3001594
Plug-in bridge, pitch: 6.2 mm, number of positions: 3, color: red
Plug-in bridge - FBSR 4-6 - 3001595
Plug-in bridge, pitch: 6.2 mm, number of positions: 4, color: red
17. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 17 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
Plug-in bridge - FBSR 5-6 - 3001596
Plug-in bridge, pitch: 6.2 mm, number of positions: 5, color: red
Plug-in bridge - FBSR 10-6 - 3033716
Plug-in bridge, pitch: 6.2 mm, number of positions: 10, color: red
Plug-in bridge - FBS 2-6 BU - 3036932
Plug-in bridge, pitch: 6.2 mm, width: 10.7 mm, number of positions: 2, color: blue
Plug-in bridge - FBS 3-6 BU - 3036945
Plug-in bridge, pitch: 6.2 mm, width: 16.9 mm, number of positions: 3, color: blue
Plug-in bridge - FBS 4-6 BU - 3036958
Plug-in bridge, pitch: 6.2 mm, width: 23.1 mm, number of positions: 4, color: blue
18. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 18 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
Plug-in bridge - FBS 5-6 BU - 3036961
Plug-in bridge, pitch: 6.2 mm, width: 29.3 mm, number of positions: 5, color: blue
Plug-in bridge - FBS 10-6 BU - 3032198
Plug-in bridge, pitch: 6.2 mm, width: 60.3 mm, number of positions: 10, color: blue
Plug-in bridge - FBS 20-6 BU - 3032208
Plug-in bridge, pitch: 6.2 mm, width: 122.3 mm, number of positions: 20, color: blue
Plug-in bridge - FBS 50-6 BU - 3032211
Plug-in bridge, pitch: 6.2 mm, width: 308.3 mm, number of positions: 50, color: blue
Labeled terminal marker
Zack marker strip - ZB 6 CUS - 0824992
Zack marker strip, can be ordered: Strip, white, labeled according to customer specifications, mounting type: snap into
tall marker groove, for terminal block width: 6.2 mm, lettering field size: 6.15 x 10.5 mm
19. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 19 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
Zack marker strip - ZB 6,LGS:FORTL.ZAHLEN - 1051016
Zack marker strip, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, printed horizontally: Consecutive
numbers 1 - 10, 11 - 20, etc. up to 491 - 500, mounting type: snap into tall marker groove, for terminal block width: 6.2
mm, lettering field size: 6.15 x 10.5 mm
Zack marker strip - ZB 6,QR:FORTL.ZAHLEN - 1051029
Zack marker strip, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, Printed vertically: Consecutive numbers
1 - 10, 11 - 20, etc. up to 491 - 500, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm,
lettering field size: 6.15 x 10.5 mm
Zack marker strip - ZB 6,LGS:GLEICHE ZAHLEN - 1051032
Zack marker strip, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, printed horizontally: Identical numbers 1
or 2, etc. up to 100, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 6.15
x 10.5 mm
Marker for terminal blocks - ZB 6,LGS:L1-N,PE - 1051414
Marker for terminal blocks, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, Horizontal: L1, L2, L3, N, PE,
L1, L2, L3, N, PE, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 6.15 x
10.5 mm
Marker for terminal blocks - ZB 6,LGS:U-N - 1051430
Marker for terminal blocks, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, printed horizontally: U, V, W,
N, GND, U, V, W, N, GND, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering field
size: 6.15 x 10.5 mm
20. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 20 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
Marker for terminal blocks - UC-TM 6 CUS - 0824589
Marker for terminal blocks, can be ordered: by sheet, white, labeled according to customer specifications, mounting type:
snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 5.6 x 10.5 mm
Marker for terminal blocks - UCT-TM 6 CUS - 0829602
Marker for terminal blocks, can be ordered: by sheet, white, labeled according to customer specifications, mounting type:
snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 5.6 x 10.5 mm
Marker pen
Marker pen - X-PEN 0,35 - 0811228
Marker pen without ink cartridge, for manual labeling of markers, labeling extremely wipe-proof, line thickness 0.35 mm
Partition plate
Partition plate - ATP-UT - 3047167
Partition plate, length: 50 mm, width: 2.2 mm, height: 48 mm, color: gray
Planning and marking software
21. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 21 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
Software - CLIP-PROJECT ADVANCED - 5146040
Multilingual software for convenient configuration of Phoenix Contact products on standard DIN rails.
Software - CLIP-PROJECT PROFESSIONAL - 5146053
Multilingual software for terminal strip configuration. A marking module enables the professional marking of markers and
labels for identifying terminal blocks, conductors and cables, and devices.
Screwdriver tools
Screwdriver - SZS 0,6X3,5 - 1205053
Actuation tool, for ST terminal blocks, insulated, also suitable for use as a bladed screwdriver, size: 0.6 x 3.5 x 100 mm,
2-component grip, with non-slip grip
Screwdriver - SF-SL 0,6X3,5-100 S-VDE - 1212587
Actuation tool, for ST terminal blocks, VDE insulated, with slimmer insulation integrated in the blade, also suitable for use
as a bladed screwdriver, size: 0.6 x 3.5 x 100 mm, 2-component grip, with non-slip grip
Short-circuit connector
Short-circuit connector - FBSRH 2-6 - 3033812
Short-circuit connector, pitch: 6.2 mm, number of positions: 2, color: red
22. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 22 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
Terminal marking
Zack marker strip - ZB 6:UNBEDRUCKT - 1051003
Zack marker strip, Strip, white, unlabeled, can be labeled with: CMS-P1-PLOTTER, PLOTMARK, mounting type: snap
into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 6.15 x 10.5 mm
Marker for terminal blocks - UC-TM 6 - 0818085
Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: BLUEMARK CLED, BLUEMARK LED, CMS-P1-
PLOTTER, PLOTMARK, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size:
5.6 x 10.5 mm
Marker for terminal blocks - UCT-TM 6 - 0828736
Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: THERMOMARK PRIME, THERMOMARK
CARD, BLUEMARK CLED, BLUEMARK LED, TOPMARK LASER, mounting type: snap into tall marker groove, for
terminal block width: 6.2 mm, lettering field size: 5.6 x 10.5 mm
Test plug terminal block
Test plugs - MPS-MT - 0201744
Test plugs, with solder connection up to 1 mm² conductor cross section, color: silver
23. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 23 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
Test plugs - PS-6 - 3030996
Test plugs, color: red
Test plugs - PS-6/2,3MM RD - 3038736
Test plugs, color: red
Test socket
Test adapter - PAI-4-FIX-5/6 BU - 3035975
4 mm test adapter, for terminal blocks with 5.2 mm and 6.2 mm pitch
Test adapter - PAI-4-FIX-5/6 OG - 3035974
4 mm test adapter, for terminal blocks with 5.2 mm and 6.2 mm pitch
Test adapter - PAI-4-FIX-5/6 YE - 3035977
4 mm test adapter, for terminal blocks with 5.2 mm and 6.2 mm pitch
24. https://www.phoenixcontact.com/us/products/3044102
09/13/2017 Page 24 / 25
Feed-through terminal block - UT 4 - 3044102
Accessories
Test adapter - PAI-4-FIX-5/6 RD - 3035976
4 mm test adapter, for terminal blocks with 5.2 mm and 6.2 mm pitch
Test adapter - PAI-4-FIX-5/6 GN - 3035978
4 mm test adapter, for terminal blocks with 5.2 mm and 6.2 mm pitch
Test adapter - PAI-4-FIX-5/6 BK - 3035980
4 mm test adapter, for terminal blocks with 5.2 mm and 6.2 mm pitch
Test adapter - PAI-4-FIX-5/6 GY - 3035982
4 mm test adapter, for terminal blocks with 5.2 mm and 6.2 mm pitch
Test adapter - PAI-4-FIX-5/6 VT - 3035979
4 mm test adapter, for terminal blocks with 5.2 mm and 6.2 mm pitch
