This paper deals with the comparative study of heat sink having fins with shield of various profiles namely Trapezoidal with curved and plane inclination and slope shield as heat sinks are the commonly used devices for enhancing heat transfer in electronic components. For the purpose of study heat sink is modeled by using the optimal geometric parameter such as fin height, fin thickness, base height, fin pitch as 48 mm, 1.6 mm, 8mm, 4mm and after that simulation is done at
heat load of 75W and with a air velocity of 4.7171m/s and air inlet temperature is taken as 295 K. The simulation is carried out with a commercial package provided by fluent incorporation.
THERMAL ANALYSIS OF A HEAT SINK FOR ELECTRONICS COOLINGIAEME Publication
Heat transfer is a discipline of thermal engineering that concern the generation, use, conversion and exchange of thermal energy, heat between physical systems. Heat transfer is classified in to various mechanisms such as heat conduction, convection, thermal radiation & transfer of energy by phase change. Most of the electronic equipment are low power and produce negligible amount of heat in their operation. Some devices, such as power transistors, CPU's, & power diodes produce a significant amount of heat. so sufficient measures are need to be taken so as to prolong their working life and reliability.
The present trend in the electronic packaging industry is to reduce the size and increase the performance of the equipment. As the power of these systems increases and the volume allowed diminishes, heat flux or density is spiraled. The cooling of modern electronic components is one of the prime areas for the application of thermal control techniques. Of the many thermal-cooling techniques, forced air-cooling being one such extensively used technique due to its simple design and easy availability of air. The present study is to design an air cooled high power electronic system to dissipate heat from selected electronic components.
Cfd and conjugate heat transfer analysis of heat sinks with different fin geo...eSAT Journals
Abstract Heat sinks are commonly used for cooling of electronic devices. Heat sinks, an array of heat fins, remove the heat from the surfaces of the chips by enhancing the heat Transfer rate through heat conduction process. Heat can also be removed from the chip surfaces through forced convection heat transfer. In this project work, CFD and conjugate heat transfer analysis is carried out for various fin geometries with Zigzag, Fluted, Slanted mirror, Custom pin fin and staggered array configurations for low thermal resistance and minimum pressure drop. Numerical simulations are carried out for each of the above mentioned fin geometries with common base plate thickness of 2 mm, fin height of 28 mm and fin thickness of 1 mm for three different heat loads namely 50 W, 75 W and 100 W with air flow of 3.933 m/s (15 ft3/min or 15 CFM) and air inlet temperature of 25oC. The results are compared for thermal performance of a heat sink for each of above geometries and it is observe that the fin with Slanted Mirror geometry gives the best performance among all the other geometries for minimum Pressure drop. The average heat transfer coefficients for fins with slanted mirror geometry, zig zag configuration, fluted type, custom pin fin and staggered array are found to be 215 W/m2K, 164 W/m2K, 164 W/m2K, 157 W/m2K and 145 W/m2K respectively Keywords: Fin geometries of Heat sinks, Computational Fluid Dynamics, Conjugate heat transfer.
Water cooled minichannel heat sinks for microprocessor cooling: Effect of fin...Danial Sohail
Heat sink with different fin spacing mounted on a microprocessor were tested for their heat removing capabilities by varying coolant flow rates over them
Experimentation and analysis of heat transfer through perforated fins of diff...SharathKumar528
Engineering Project by Abhijath HB, Dashartha H S, Akshay Mohanraj and Sharath Kumar M S involving analysis of Fins( Heat exchanging extensions) with various geometrical perforations.
THERMAL ANALYSIS OF A HEAT SINK FOR ELECTRONICS COOLINGIAEME Publication
Heat transfer is a discipline of thermal engineering that concern the generation, use, conversion and exchange of thermal energy, heat between physical systems. Heat transfer is classified in to various mechanisms such as heat conduction, convection, thermal radiation & transfer of energy by phase change. Most of the electronic equipment are low power and produce negligible amount of heat in their operation. Some devices, such as power transistors, CPU's, & power diodes produce a significant amount of heat. so sufficient measures are need to be taken so as to prolong their working life and reliability.
The present trend in the electronic packaging industry is to reduce the size and increase the performance of the equipment. As the power of these systems increases and the volume allowed diminishes, heat flux or density is spiraled. The cooling of modern electronic components is one of the prime areas for the application of thermal control techniques. Of the many thermal-cooling techniques, forced air-cooling being one such extensively used technique due to its simple design and easy availability of air. The present study is to design an air cooled high power electronic system to dissipate heat from selected electronic components.
Cfd and conjugate heat transfer analysis of heat sinks with different fin geo...eSAT Journals
Abstract Heat sinks are commonly used for cooling of electronic devices. Heat sinks, an array of heat fins, remove the heat from the surfaces of the chips by enhancing the heat Transfer rate through heat conduction process. Heat can also be removed from the chip surfaces through forced convection heat transfer. In this project work, CFD and conjugate heat transfer analysis is carried out for various fin geometries with Zigzag, Fluted, Slanted mirror, Custom pin fin and staggered array configurations for low thermal resistance and minimum pressure drop. Numerical simulations are carried out for each of the above mentioned fin geometries with common base plate thickness of 2 mm, fin height of 28 mm and fin thickness of 1 mm for three different heat loads namely 50 W, 75 W and 100 W with air flow of 3.933 m/s (15 ft3/min or 15 CFM) and air inlet temperature of 25oC. The results are compared for thermal performance of a heat sink for each of above geometries and it is observe that the fin with Slanted Mirror geometry gives the best performance among all the other geometries for minimum Pressure drop. The average heat transfer coefficients for fins with slanted mirror geometry, zig zag configuration, fluted type, custom pin fin and staggered array are found to be 215 W/m2K, 164 W/m2K, 164 W/m2K, 157 W/m2K and 145 W/m2K respectively Keywords: Fin geometries of Heat sinks, Computational Fluid Dynamics, Conjugate heat transfer.
Water cooled minichannel heat sinks for microprocessor cooling: Effect of fin...Danial Sohail
Heat sink with different fin spacing mounted on a microprocessor were tested for their heat removing capabilities by varying coolant flow rates over them
Experimentation and analysis of heat transfer through perforated fins of diff...SharathKumar528
Engineering Project by Abhijath HB, Dashartha H S, Akshay Mohanraj and Sharath Kumar M S involving analysis of Fins( Heat exchanging extensions) with various geometrical perforations.
Solar air heater (SAH), which is the most essential component of solar drying systems, receive solar energy and convert it into thermal energy. This review presents descriptions and previous works conducted on performances analysis of SAHs. Exergoenviroeconomic, exergoenvironmental, environmental, and exergy analyses are also presented. In addition, results on the performances of SAHs are summarized. The exergy and energy efficiencies of SAHs at laboratorium testing range from 8% to 61% and from 30% to 79%, respectively.
The main objectives of the heat transfer analysis is to enhance the heat transfer rate from system to
surrounding. To transfer the heat from any system either by conduction or convection medium. Both modes of
heat transfer has been enhanced by providing an additional equipments in the outer periphery of the heat transfer
system.Fins are basically mechanical structures which are used to cool various structures by the process of
convection. Most part of their design is basically limited by the design of the system. But still certain parameters
and geometry could be modified to better heat transfer. In most of the cases simple fin geometry is preferred such
as rectangular fins and circular fins. Many experimental works has been done to improve the heat release of the
internal combustion engine cylinder and improves fin efficiency.This study presents the results of air flow and
heat transfer in a light weight automobile engine, considering fins with dimple to increase the heat transfer rate.
An analysis has been using ANSYS WORKBENCH version 12.0 was conducted to find the optimum number of
dimples to maximizing the heat transfer across the Automobile engine body. The results indicate that the
presence of fins with dimple shows improved results on the basis of heat transfer.
Enhancement of Heat Transfer Analysis and Optimization of Engine Fins of Vary...ijtsrd
The Engine cylinder is one of the major automobile components, which is subjected to high temperature variations and thermal stresses. In order to cool the cylinder, fins are provided on the cylinder to increase the rate of heat transfer. By doing thermal analysis on the engine cylinder fins, it is helpful to know the heat dissipation inside the cylinder. The principle implemented in this project is to increase the heat dissipation rate by using the invisible working fluid, nothing but air. As know, by increasing the surface area we can increase the heat dissipation rate, so designing such a large complex engine is very difficult. The main purpose of using these cooling fins is to cool the engine cylinder by air. The main aim of the project is to analyse the thermal properties by varying geometry, material, distance between the fins and thickness of cylinder fins. Parametric models of cylinder with fins have been developed to predict the transient thermal behaviour. The models are created by varying the geometry circular and also by varying thickness of the fins for both geometries. The 3D modelling software used is Pro/Engineer. Thermal analysis is done on the cylinder fins to determine variation temperature distribution over time. The analysis is done using ANSYS. Thermal analysis determines temperatures and other thermal quantities. In this thesis, using materials cast iron, Copper and Aluminium alloy 6082 are also for cylinder fin body. Thermal analysis is done using all the three materials by changing geometries, distance between the fins and thickness of the fins for the actual model of the cylinder fin body. K. Karthikeyan | C. Saravanan | Dr. T. Senthil Kumar"Enhancement of Heat Transfer Analysis and Optimization of Engine Fins of Varying Geometry" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-2 | Issue-4 , June 2018, URL: http://www.ijtsrd.com/papers/ijtsrd14327.pdf http://www.ijtsrd.com/engineering/mechanical-engineering/14327/enhancement-of-heat-transfer-analysis-and-optimization-of-engine-fins-of-varying-geometry/k-karthikeyan
ENERGY SAVINGS IN DOMESTIC REFRIGERATOR USING TWO THERMOELECTRIC MODULES& WAT...ijiert bestjournal
The study deals with hybrid refrigerator that combi nes thermoelectric (TER) and vapor compression refrigeration (VCR) and also entail exp erimental details of combined VCR & TER system. Objective is to configure hybrid refrig erator by introducing two Peltier modules (TER) in domestic refrigerator and to analyze compr essor cycles of conventional refrigerator with TER to increase energy efficiency of vapor com pression cycle. For this comparison of standalone VCR and Hybrid VCR+TER system is carried out. A Peltier module of size 4cm � 4cm � .4cm is introduced in the refrigerator cabinet & t he effect on energy efficiency in terms of trip time of compressor is recorded. The e ffect of Air cooled & Water cooled condenser with TER in different structures is also investigated. It is observed that by introducing thermoelectric effect,energy consumpti on of VCR is reduced by almost 10.92% annually,which accounts for 80 units per year. Thu s ultimately improving COP of the hybrid system with better control on temperature over the total run time.
Analysis of Coiled-Tube Heat Exchangers to Improve Heat Transfer Rate With Sp...IJMER
Steady heat transfer enhancement has been studied in helically coiled-tube heat exchangers. The outer side of the wall of the heat exchanger contains a helical corrugation which makes a helical rib on the inner side of the tube wall to induce additional swirling motion of fluid particles. Numerical calculations have been carried out to examine different geometrical parameters and the impact of flow and thermal boundary conditions for the heat transfer rate in laminar and transitional flow regimes. Calculated results have been compared to existing empirical formula and experimental tests to investigate the validity of the numerical results in case of common helical tube heat exchanger and additionally results of the numerical computation of corrugated straight tubes for laminar and transition flow have been validated with experimental tests available in the literature. Comparison of the flow and temperature fields in case of common helical tube and the coil with spirally corrugated wall configuration are discussed. Heat exchanger coils with helically corrugated wall configuration show 80–100% increase for the inner side heat transfer rate due to the additionally developed swirling motion while the relative pressure drop is 10–600% larger compared to the common helically coiled heat exchangers. New empirical Co-relation has been proposed for the fully developed inner side heat transfer prediction in case of helically corrugated wall configuration.
Numerical Analysis of Heat Transfer Enhancement in Pipe-inPipe Helical Coiled...iosrjce
These paper focuses on the effect of the inside tubes at constant value of mass flow rate and variation
of annulus mass flow rate on effect of Dean Number and overall heat transfer coefficient with constant wall
temperature, CFD analysis of a helically coiled heat exchanger. Also deals with the effect of Dean Number with
respect to Reynolds Number and Nusselt Number and Overall Heat Transfer coefficient on change of coil
configuration of helically coiled tube. The particular difference in this study in comparison with the other
similar studies was the boundary conditions for the helical coils. The results indicate that with the decrease the
inner coil diameter, the overall heat transfer coefficient is increased
Heat exchangers are used widely in industrial application such as chemical,
food processing, power production, refrigeration and air-conditioning
industries. Helical coiled heat exchangers are used in order to obtain a large
heat transfer per unit volume and to enhance the heat transfer rate on the inside
surface. In the present study, CFD simulations are carried out for a counter
flow tube in tube helical heat exchanger where hot water flows through the
inner tube and cold water flows through the outer tube. From the simulation
results heat transfer coefficient, pressure drop and nusselt number are
calculated. The heat transfer characteristics of the same are compared with that
of a counter flow tube in tube straight tube heat exchanger of same length
under same temperature and flow conditions. CFD simulation results showed
that the helical tube in tube heat exchanger is more effective than the straight
tube in tube heat exchanger.
An experimental investigation of annular fins under forced convectioneSAT Journals
Abstract
Heat transfer characteristics under forced convection are investigated experimentally by varying parameters like surface area,
base-to-ambient temperature difference and Reynolds number. To investigate the performance of fins experimentally, fins made of
aluminium (high thermal conductivity) are taken. For varying the surface area fin with 11 mm diameter without circumferential
fins, fin with 31 mm diameter and annular fins of 31 mm diameter are taken as specimens. Base to ambient temperature difference
is varied with the aid of dimmerstat ranging from 25W to 45W. Reynolds number is also varied by varying the velocities of air.
Velocities are varied by the aid of fan. Then these fins are tested under different load conditions, different Reynolds number by
varying the surface area of fins increase the rate of heat transfer. With the variation of relevant parameters under forced
convection heat transfer rates are analyzed experimentally. Experiments are conducted by using the annular fins, fin with
diameter 11mm without circumferential fins and fin with diameter 31mm at different Reynolds number and loads under forced
convection and comparison is made between fins. Experimental results shows that forced convection heat transfer rate from fins
depend on surface areas, base ambient temperature difference and Reynolds number. The base temperature for annular fins is
reduced by 30% when compared to fin with diameter 11mm due to increase in surface area about 40%. The base temperature for
annular fins is reduced by 10% when compared to fin with diameter of 31mm due to decrease in surface area about 41%. It is
also observed that at higher heat load i.e., 45W, the overall fin efficiency of annular fins is increased by 44% and 8% compared to
fin with diameter of 11mm and 31mm respectively. At higher Reynolds number range 800-2000, heat transfer rate increases in
annular fins due to more number of air molecules get in contact with the heated surface
International Journal of Engineering Research and Applications (IJERA) aims to cover the latest outstanding developments in the field of all Engineering Technologies & science.
International Journal of Engineering Research and Applications (IJERA) is a team of researchers not publication services or private publications running the journals for monetary benefits, we are association of scientists and academia who focus only on supporting authors who want to publish their work. The articles published in our journal can be accessed online, all the articles will be archived for real time access.
Our journal system primarily aims to bring out the research talent and the works done by sciaentists, academia, engineers, practitioners, scholars, post graduate students of engineering and science. This journal aims to cover the scientific research in a broader sense and not publishing a niche area of research facilitating researchers from various verticals to publish their papers. It is also aimed to provide a platform for the researchers to publish in a shorter of time, enabling them to continue further All articles published are freely available to scientific researchers in the Government agencies,educators and the general public. We are taking serious efforts to promote our journal across the globe in various ways, we are sure that our journal will act as a scientific platform for all researchers to publish their works online.
EXPERIMENTAL STUDY OF MIXED CONVECTION HEAT TRANSFER USING CIRCULAR, SQUARE, ...ijiert bestjournal
Pulling Fins are extended surfaces employed to enha nce the convective heat transfer from a surface for increasing heat dissipation. Fins with various geometries have been designed and used in various cooling application the selection o f particular fins configuration in any heat transfer application is an important state in desig ned process and takes into account the space,weight,manufacturing technique and cost considerat ion as well as the thermal characteristics it exhibits. Fins cross section profiles have profo und influence on thermal characteristics of Annular Fins and the surface area changes with chan ge of cross section of fins. This study deals with studying the performance of various avai lable fins profiles. Widely used fins profile viz. Rectangular,Triangular,Trapezoidal,Circular,Rhombic,and Elliptical Fins. In Addition to the normal configuration of fins,to ne w configurations were designed and created.
EXPERIMENTAL STUDY OF HEAT TRANSFER FROM PLATE FIN ARRAY IN MIXED CONVECTION ...ijiert bestjournal
The work summarized in this paper presents an exper imental study of heat transfer from plate fin in mixed convection mode enhancement by the us e of plate fins is presented. After a brief review of the basic methods used to enhance the hea t transfer by simultaneous increase of heat transfer surface area as well as the heat tran sfer coefficient,a simple experimental method to assess the heat transfer enhancement is p resented. The method is demonstrated on plate fins as elements for the heat transfer enhanc ement,but it can in principle be applied also to other fin forms. That is varying various paramet ers (height,spacing). The order of the magnitude of heat transfer enhancement obtained exp erimentally,it was found that by a direct comparison of Nu and Re no conclusion regarding the relative performances could be made. This is because the dimensionless variables are int roduced for the scaling of heat transfer and pressure drop results from laboratory to large scal e but not for the performance comparison. Therefore a literature survey of the performance co mparison methods used in the past was also performed. Experiments will carried out on mix ed convection heat transfer from plate fin heat sinks subject to the influence of its geometry and heat flux. A total of 9 plate fins were pasted into the upper surface of the base plate. Th e area of the base plate is 150mm by 150mm. The base plate and the fins were made of alu minum. For all tested plate fin heat sinks,however,the heat transfer performance for h eat sinks with plate fins was better than that of solid pins.
EXPERIMENTAL INVESTIGATION OF CONVECTION HEAT TRANSFER FOR LAMINAR FLOW IN AN...IAEME Publication
The present paper investigate convection heat transfer for laminar flow in an inclined concentrated with 54mm outside diameter and 800 mm length pipe. The pipe was exposed to
constant heat flux of 529 W/m2 by other internal tube which was an electric element with 6.3 mm diameter and 600mm length. The pipe kit was rotated by ten declination angles, which were varied from (0O to 90O ) by 10O for each step.
Solar air heater (SAH), which is the most essential component of solar drying systems, receive solar energy and convert it into thermal energy. This review presents descriptions and previous works conducted on performances analysis of SAHs. Exergoenviroeconomic, exergoenvironmental, environmental, and exergy analyses are also presented. In addition, results on the performances of SAHs are summarized. The exergy and energy efficiencies of SAHs at laboratorium testing range from 8% to 61% and from 30% to 79%, respectively.
The main objectives of the heat transfer analysis is to enhance the heat transfer rate from system to
surrounding. To transfer the heat from any system either by conduction or convection medium. Both modes of
heat transfer has been enhanced by providing an additional equipments in the outer periphery of the heat transfer
system.Fins are basically mechanical structures which are used to cool various structures by the process of
convection. Most part of their design is basically limited by the design of the system. But still certain parameters
and geometry could be modified to better heat transfer. In most of the cases simple fin geometry is preferred such
as rectangular fins and circular fins. Many experimental works has been done to improve the heat release of the
internal combustion engine cylinder and improves fin efficiency.This study presents the results of air flow and
heat transfer in a light weight automobile engine, considering fins with dimple to increase the heat transfer rate.
An analysis has been using ANSYS WORKBENCH version 12.0 was conducted to find the optimum number of
dimples to maximizing the heat transfer across the Automobile engine body. The results indicate that the
presence of fins with dimple shows improved results on the basis of heat transfer.
Enhancement of Heat Transfer Analysis and Optimization of Engine Fins of Vary...ijtsrd
The Engine cylinder is one of the major automobile components, which is subjected to high temperature variations and thermal stresses. In order to cool the cylinder, fins are provided on the cylinder to increase the rate of heat transfer. By doing thermal analysis on the engine cylinder fins, it is helpful to know the heat dissipation inside the cylinder. The principle implemented in this project is to increase the heat dissipation rate by using the invisible working fluid, nothing but air. As know, by increasing the surface area we can increase the heat dissipation rate, so designing such a large complex engine is very difficult. The main purpose of using these cooling fins is to cool the engine cylinder by air. The main aim of the project is to analyse the thermal properties by varying geometry, material, distance between the fins and thickness of cylinder fins. Parametric models of cylinder with fins have been developed to predict the transient thermal behaviour. The models are created by varying the geometry circular and also by varying thickness of the fins for both geometries. The 3D modelling software used is Pro/Engineer. Thermal analysis is done on the cylinder fins to determine variation temperature distribution over time. The analysis is done using ANSYS. Thermal analysis determines temperatures and other thermal quantities. In this thesis, using materials cast iron, Copper and Aluminium alloy 6082 are also for cylinder fin body. Thermal analysis is done using all the three materials by changing geometries, distance between the fins and thickness of the fins for the actual model of the cylinder fin body. K. Karthikeyan | C. Saravanan | Dr. T. Senthil Kumar"Enhancement of Heat Transfer Analysis and Optimization of Engine Fins of Varying Geometry" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-2 | Issue-4 , June 2018, URL: http://www.ijtsrd.com/papers/ijtsrd14327.pdf http://www.ijtsrd.com/engineering/mechanical-engineering/14327/enhancement-of-heat-transfer-analysis-and-optimization-of-engine-fins-of-varying-geometry/k-karthikeyan
ENERGY SAVINGS IN DOMESTIC REFRIGERATOR USING TWO THERMOELECTRIC MODULES& WAT...ijiert bestjournal
The study deals with hybrid refrigerator that combi nes thermoelectric (TER) and vapor compression refrigeration (VCR) and also entail exp erimental details of combined VCR & TER system. Objective is to configure hybrid refrig erator by introducing two Peltier modules (TER) in domestic refrigerator and to analyze compr essor cycles of conventional refrigerator with TER to increase energy efficiency of vapor com pression cycle. For this comparison of standalone VCR and Hybrid VCR+TER system is carried out. A Peltier module of size 4cm � 4cm � .4cm is introduced in the refrigerator cabinet & t he effect on energy efficiency in terms of trip time of compressor is recorded. The e ffect of Air cooled & Water cooled condenser with TER in different structures is also investigated. It is observed that by introducing thermoelectric effect,energy consumpti on of VCR is reduced by almost 10.92% annually,which accounts for 80 units per year. Thu s ultimately improving COP of the hybrid system with better control on temperature over the total run time.
Analysis of Coiled-Tube Heat Exchangers to Improve Heat Transfer Rate With Sp...IJMER
Steady heat transfer enhancement has been studied in helically coiled-tube heat exchangers. The outer side of the wall of the heat exchanger contains a helical corrugation which makes a helical rib on the inner side of the tube wall to induce additional swirling motion of fluid particles. Numerical calculations have been carried out to examine different geometrical parameters and the impact of flow and thermal boundary conditions for the heat transfer rate in laminar and transitional flow regimes. Calculated results have been compared to existing empirical formula and experimental tests to investigate the validity of the numerical results in case of common helical tube heat exchanger and additionally results of the numerical computation of corrugated straight tubes for laminar and transition flow have been validated with experimental tests available in the literature. Comparison of the flow and temperature fields in case of common helical tube and the coil with spirally corrugated wall configuration are discussed. Heat exchanger coils with helically corrugated wall configuration show 80–100% increase for the inner side heat transfer rate due to the additionally developed swirling motion while the relative pressure drop is 10–600% larger compared to the common helically coiled heat exchangers. New empirical Co-relation has been proposed for the fully developed inner side heat transfer prediction in case of helically corrugated wall configuration.
Numerical Analysis of Heat Transfer Enhancement in Pipe-inPipe Helical Coiled...iosrjce
These paper focuses on the effect of the inside tubes at constant value of mass flow rate and variation
of annulus mass flow rate on effect of Dean Number and overall heat transfer coefficient with constant wall
temperature, CFD analysis of a helically coiled heat exchanger. Also deals with the effect of Dean Number with
respect to Reynolds Number and Nusselt Number and Overall Heat Transfer coefficient on change of coil
configuration of helically coiled tube. The particular difference in this study in comparison with the other
similar studies was the boundary conditions for the helical coils. The results indicate that with the decrease the
inner coil diameter, the overall heat transfer coefficient is increased
Heat exchangers are used widely in industrial application such as chemical,
food processing, power production, refrigeration and air-conditioning
industries. Helical coiled heat exchangers are used in order to obtain a large
heat transfer per unit volume and to enhance the heat transfer rate on the inside
surface. In the present study, CFD simulations are carried out for a counter
flow tube in tube helical heat exchanger where hot water flows through the
inner tube and cold water flows through the outer tube. From the simulation
results heat transfer coefficient, pressure drop and nusselt number are
calculated. The heat transfer characteristics of the same are compared with that
of a counter flow tube in tube straight tube heat exchanger of same length
under same temperature and flow conditions. CFD simulation results showed
that the helical tube in tube heat exchanger is more effective than the straight
tube in tube heat exchanger.
An experimental investigation of annular fins under forced convectioneSAT Journals
Abstract
Heat transfer characteristics under forced convection are investigated experimentally by varying parameters like surface area,
base-to-ambient temperature difference and Reynolds number. To investigate the performance of fins experimentally, fins made of
aluminium (high thermal conductivity) are taken. For varying the surface area fin with 11 mm diameter without circumferential
fins, fin with 31 mm diameter and annular fins of 31 mm diameter are taken as specimens. Base to ambient temperature difference
is varied with the aid of dimmerstat ranging from 25W to 45W. Reynolds number is also varied by varying the velocities of air.
Velocities are varied by the aid of fan. Then these fins are tested under different load conditions, different Reynolds number by
varying the surface area of fins increase the rate of heat transfer. With the variation of relevant parameters under forced
convection heat transfer rates are analyzed experimentally. Experiments are conducted by using the annular fins, fin with
diameter 11mm without circumferential fins and fin with diameter 31mm at different Reynolds number and loads under forced
convection and comparison is made between fins. Experimental results shows that forced convection heat transfer rate from fins
depend on surface areas, base ambient temperature difference and Reynolds number. The base temperature for annular fins is
reduced by 30% when compared to fin with diameter 11mm due to increase in surface area about 40%. The base temperature for
annular fins is reduced by 10% when compared to fin with diameter of 31mm due to decrease in surface area about 41%. It is
also observed that at higher heat load i.e., 45W, the overall fin efficiency of annular fins is increased by 44% and 8% compared to
fin with diameter of 11mm and 31mm respectively. At higher Reynolds number range 800-2000, heat transfer rate increases in
annular fins due to more number of air molecules get in contact with the heated surface
International Journal of Engineering Research and Applications (IJERA) aims to cover the latest outstanding developments in the field of all Engineering Technologies & science.
International Journal of Engineering Research and Applications (IJERA) is a team of researchers not publication services or private publications running the journals for monetary benefits, we are association of scientists and academia who focus only on supporting authors who want to publish their work. The articles published in our journal can be accessed online, all the articles will be archived for real time access.
Our journal system primarily aims to bring out the research talent and the works done by sciaentists, academia, engineers, practitioners, scholars, post graduate students of engineering and science. This journal aims to cover the scientific research in a broader sense and not publishing a niche area of research facilitating researchers from various verticals to publish their papers. It is also aimed to provide a platform for the researchers to publish in a shorter of time, enabling them to continue further All articles published are freely available to scientific researchers in the Government agencies,educators and the general public. We are taking serious efforts to promote our journal across the globe in various ways, we are sure that our journal will act as a scientific platform for all researchers to publish their works online.
EXPERIMENTAL STUDY OF MIXED CONVECTION HEAT TRANSFER USING CIRCULAR, SQUARE, ...ijiert bestjournal
Pulling Fins are extended surfaces employed to enha nce the convective heat transfer from a surface for increasing heat dissipation. Fins with various geometries have been designed and used in various cooling application the selection o f particular fins configuration in any heat transfer application is an important state in desig ned process and takes into account the space,weight,manufacturing technique and cost considerat ion as well as the thermal characteristics it exhibits. Fins cross section profiles have profo und influence on thermal characteristics of Annular Fins and the surface area changes with chan ge of cross section of fins. This study deals with studying the performance of various avai lable fins profiles. Widely used fins profile viz. Rectangular,Triangular,Trapezoidal,Circular,Rhombic,and Elliptical Fins. In Addition to the normal configuration of fins,to ne w configurations were designed and created.
EXPERIMENTAL STUDY OF HEAT TRANSFER FROM PLATE FIN ARRAY IN MIXED CONVECTION ...ijiert bestjournal
The work summarized in this paper presents an exper imental study of heat transfer from plate fin in mixed convection mode enhancement by the us e of plate fins is presented. After a brief review of the basic methods used to enhance the hea t transfer by simultaneous increase of heat transfer surface area as well as the heat tran sfer coefficient,a simple experimental method to assess the heat transfer enhancement is p resented. The method is demonstrated on plate fins as elements for the heat transfer enhanc ement,but it can in principle be applied also to other fin forms. That is varying various paramet ers (height,spacing). The order of the magnitude of heat transfer enhancement obtained exp erimentally,it was found that by a direct comparison of Nu and Re no conclusion regarding the relative performances could be made. This is because the dimensionless variables are int roduced for the scaling of heat transfer and pressure drop results from laboratory to large scal e but not for the performance comparison. Therefore a literature survey of the performance co mparison methods used in the past was also performed. Experiments will carried out on mix ed convection heat transfer from plate fin heat sinks subject to the influence of its geometry and heat flux. A total of 9 plate fins were pasted into the upper surface of the base plate. Th e area of the base plate is 150mm by 150mm. The base plate and the fins were made of alu minum. For all tested plate fin heat sinks,however,the heat transfer performance for h eat sinks with plate fins was better than that of solid pins.
EXPERIMENTAL INVESTIGATION OF CONVECTION HEAT TRANSFER FOR LAMINAR FLOW IN AN...IAEME Publication
The present paper investigate convection heat transfer for laminar flow in an inclined concentrated with 54mm outside diameter and 800 mm length pipe. The pipe was exposed to
constant heat flux of 529 W/m2 by other internal tube which was an electric element with 6.3 mm diameter and 600mm length. The pipe kit was rotated by ten declination angles, which were varied from (0O to 90O ) by 10O for each step.
AN EXPERIMENTAL STUDY OF HEAT TRANSFER IN A CORRUGATED PLATE HEAT EXCHANGER IAEME Publication
In the present work an attempt has been made to investigate the performance of a corrugated plate heat exchanger by the first law and the second law of thermodynamics. Experiments were conducted to determine the laminar convective heat transfer characteristics for fully developed flow of hot and cold fluid in alternate ducts. Experiments were conducted on a three channel 1-1 pass corrugated plate heat exchanger. Hot fluid was made to flow in the central channel to get cooled by
cold fluid in the top and bottom channels in parallel and counter flow arrangements.
Nusselt number and friction factor correlations for solar air heater duct hav...IAEME Publication
In order to enhance the heat transfer rate of solar air heater apparatus, triangular protrusions are provided on the surface of the aluminum absorber plate to act as artificial roughness. Three kinds of absorber plates other than a smooth absorber plate with protrusions of varying apex angles are chosen for this work.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
EFFECT OF BAFFLES GEOMETRY ON HEAT TRANSFER ENHANCEMENT INSIDE CORRUGATED DUCTIAEME Publication
The turbulent heat transfer and friction inside a corrugated square duct inserted
with various baffles geometries have been studied experimentally. Five types of baffles
(flat, rectangular, semicircular, triangular and trapezoidal) are attached on top and
bottom walls of the duct. The effects of duct wavy surface, baffle geometry, baffle
position and flow Reynolds number are examined. Air is used as the working fluid
with Reynolds number ranged from 3442.6 to 17213.19 under constant wall heat flux.
Experimental results show obtained for average Nusselt numbers and friction factor.
The results indicate that the trapezoidal baffled geometry provides a higher thermal
performance than the other type baffled one. The present work showed that the highest
thermal performance factor under the same pumping power obtained from the
experiments, is about 2.26 times more than that of plain duct. Also, it is found that the
thermal performance of the baffles attach on the bottom wall of the duct is higher than
the other baffles attach on the top
A NUMERICAL STUDY OF HEAT TRANSFER AND FLUID FLOW IN A BANK OF TUBES WITH INT...IAEME Publication
The present work represents a two-dimensional steady state numerical investigation of heat transfer and hydrodynamic characteristics of air flow across a 3 rows of circular tube banks in triangular arrangement with triangular wake splitters placed on each tube with downstream direction (wake region). The effects of Reynolds number (from 5000 to 15000), the length of splitter are 0.5D, 1.0D, and 1.5D times of tube diameter. The study focuses on the Influence of the different
parameters of splitters on heat transfer and fluid flow characteristics of three rows tube banks. The characteristics of total heat transfer per area for each tube with and without splitter and total pressure drop are studied numerically by the aid of the computational fluid dynamics (CFD) commercial code of FLUENT 6.3.
For increasing the efficiency of the system, extended surfaces like fins are used. The heat transfer rates of different
shapes and cross sections like circular, rectangular, T-shaped and Tree shaped fins is compared. As per the data considered
from the previous works the heat transfer rate is depending on the surface area and the heat transfer coefficient,
the surface area is increasing from circular to tree shaped fins. In this paper temperature distribution of the tree shaped
fins is investigated by changing bifurcation angle, adding an extra element and the fin materials. Different cross section
of the elements is considered and will be validated.
Thermal analysis is enhanced by using Computational Fluid Dynamics ANSYS Workbench 15. Analysis will be done for
different working conditions.
Submission Deadline: 30th September 2022
Acceptance Notification: Within Three Days’ time period
Online Publication: Within 24 Hrs. time Period
Expected Date of Dispatch of Printed Journal: 5th October 2022
MODELING AND ANALYSIS OF SURFACE ROUGHNESS AND WHITE LATER THICKNESS IN WIRE-...IAEME Publication
White layer thickness (WLT) formed and surface roughness in wire electric discharge turning (WEDT) of tungsten carbide composite has been made to model through response surface methodology (RSM). A Taguchi’s standard Design of experiments involving five input variables with three levels has been employed to establish a mathematical model between input parameters and responses. Percentage of cobalt content, spindle speed, Pulse on-time, wire feed and pulse off-time were changed during the experimental tests based on the Taguchi’s orthogonal array L27 (3^13). Analysis of variance (ANOVA) revealed that the mathematical models obtained can adequately describe performance within the parameters of the factors considered. There was a good agreement between the experimental and predicted values in this study.
A STUDY ON THE REASONS FOR TRANSGENDER TO BECOME ENTREPRENEURSIAEME Publication
The study explores the reasons for a transgender to become entrepreneurs. In this study transgender entrepreneur was taken as independent variable and reasons to become as dependent variable. Data were collected through a structured questionnaire containing a five point Likert Scale. The study examined the data of 30 transgender entrepreneurs in Salem Municipal Corporation of Tamil Nadu State, India. Simple Random sampling technique was used. Garrett Ranking Technique (Percentile Position, Mean Scores) was used as the analysis for the present study to identify the top 13 stimulus factors for establishment of trans entrepreneurial venture. Economic advancement of a nation is governed upon the upshot of a resolute entrepreneurial doings. The conception of entrepreneurship has stretched and materialized to the socially deflated uncharted sections of transgender community. Presently transgenders have smashed their stereotypes and are making recent headlines of achievements in various fields of our Indian society. The trans-community is gradually being observed in a new light and has been trying to achieve prospective growth in entrepreneurship. The findings of the research revealed that the optimistic changes are taking place to change affirmative societal outlook of the transgender for entrepreneurial ventureship. It also laid emphasis on other transgenders to renovate their traditional living. The paper also highlights that legislators, supervisory body should endorse an impartial canons and reforms in Tamil Nadu Transgender Welfare Board Association.
BROAD UNEXPOSED SKILLS OF TRANSGENDER ENTREPRENEURSIAEME Publication
Since ages gender difference is always a debatable theme whether caused by nature, evolution or environment. The birth of a transgender is dreadful not only for the child but also for their parents. The pain of living in the wrong physique and treated as second class victimized citizen is outrageous and fully harboured with vicious baseless negative scruples. For so long, social exclusion had perpetuated inequality and deprivation experiencing ingrained malign stigma and besieged victims of crime or violence across their life spans. They are pushed into the murky way of life with a source of eternal disgust, bereft sexual potency and perennial fear. Although they are highly visible but very little is known about them. The common public needs to comprehend the ravaged arrogance on these insensitive souls and assist in integrating them into the mainstream by offering equal opportunity, treat with humanity and respect their dignity. Entrepreneurship in the current age is endorsing the gender fairness movement. Unstable careers and economic inadequacy had inclined one of the gender variant people called Transgender to become entrepreneurs. These tiny budding entrepreneurs resulted in economic transition by means of employment, free from the clutches of stereotype jobs, raised standard of living and handful of financial empowerment. Besides all these inhibitions, they were able to witness a platform for skill set development that ignited them to enter into entrepreneurial domain. This paper epitomizes skill sets involved in trans-entrepreneurs of Thoothukudi Municipal Corporation of Tamil Nadu State and is a groundbreaking determination to sightsee various skills incorporated and the impact on entrepreneurship.
DETERMINANTS AFFECTING THE USER'S INTENTION TO USE MOBILE BANKING APPLICATIONSIAEME Publication
The banking and financial services industries are experiencing increased technology penetration. Among them, the banking industry has made technological advancements to better serve the general populace. The economy focused on transforming the banking sector's system into a cashless, paperless, and faceless one. The researcher wants to evaluate the user's intention for utilising a mobile banking application. The study also examines the variables affecting the user's behaviour intention when selecting specific applications for financial transactions. The researcher employed a well-structured questionnaire and a descriptive study methodology to gather the respondents' primary data utilising the snowball sampling technique. The study includes variables like performance expectations, effort expectations, social impact, enabling circumstances, and perceived risk. Each of the aforementioned variables has a major impact on how users utilise mobile banking applications. The outcome will assist the service provider in comprehending the user's history with mobile banking applications.
ANALYSE THE USER PREDILECTION ON GPAY AND PHONEPE FOR DIGITAL TRANSACTIONSIAEME Publication
Technology upgradation in banking sector took the economy to view that payment mode towards online transactions using mobile applications. This system enabled connectivity between banks, Merchant and user in a convenient mode. there are various applications used for online transactions such as Google pay, Paytm, freecharge, mobikiwi, oxygen, phonepe and so on and it also includes mobile banking applications. The study aimed at evaluating the predilection of the user in adopting digital transaction. The study is descriptive in nature. The researcher used random sample techniques to collect the data. The findings reveal that mobile applications differ with the quality of service rendered by Gpay and Phonepe. The researcher suggest the Phonepe application should focus on implementing the application should be user friendly interface and Gpay on motivating the users to feel the importance of request for money and modes of payments in the application.
VOICE BASED ATM FOR VISUALLY IMPAIRED USING ARDUINOIAEME Publication
The prototype of a voice-based ATM for visually impaired using Arduino is to help people who are blind. This uses RFID cards which contain users fingerprint encrypted on it and interacts with the users through voice commands. ATM operates when sensor detects the presence of one person in the cabin. After scanning the RFID card, it will ask to select the mode like –normal or blind. User can select the respective mode through voice input, if blind mode is selected the balance check or cash withdraw can be done through voice input. Normal mode procedure is same as the existing ATM.
IMPACT OF EMOTIONAL INTELLIGENCE ON HUMAN RESOURCE MANAGEMENT PRACTICES AMONG...IAEME Publication
There is increasing acceptability of emotional intelligence as a major factor in personality assessment and effective human resource management. Emotional intelligence as the ability to build capacity, empathize, co-operate, motivate and develop others cannot be divorced from both effective performance and human resource management systems. The human person is crucial in defining organizational leadership and fortunes in terms of challenges and opportunities and walking across both multinational and bilateral relationships. The growing complexity of the business world requires a great deal of self-confidence, integrity, communication, conflict and diversity management to keep the global enterprise within the paths of productivity and sustainability. Using the exploratory research design and 255 participants the result of this original study indicates strong positive correlation between emotional intelligence and effective human resource management. The paper offers suggestions on further studies between emotional intelligence and human capital development and recommends for conflict management as an integral part of effective human resource management.
VISUALISING AGING PARENTS & THEIR CLOSE CARERS LIFE JOURNEY IN AGING ECONOMYIAEME Publication
Our life journey, in general, is closely defined by the way we understand the meaning of why we coexist and deal with its challenges. As we develop the "inspiration economy", we could say that nearly all of the challenges we have faced are opportunities that help us to discover the rest of our journey. In this note paper, we explore how being faced with the opportunity of being a close carer for an aging parent with dementia brought intangible discoveries that changed our insight of the meaning of the rest of our life journey.
A STUDY ON THE IMPACT OF ORGANIZATIONAL CULTURE ON THE EFFECTIVENESS OF PERFO...IAEME Publication
The main objective of this study is to analyze the impact of aspects of Organizational Culture on the Effectiveness of the Performance Management System (PMS) in the Health Care Organization at Thanjavur. Organizational Culture and PMS play a crucial role in present-day organizations in achieving their objectives. PMS needs employees’ cooperation to achieve its intended objectives. Employees' cooperation depends upon the organization’s culture. The present study uses exploratory research to examine the relationship between the Organization's culture and the Effectiveness of the Performance Management System. The study uses a Structured Questionnaire to collect the primary data. For this study, Thirty-six non-clinical employees were selected from twelve randomly selected Health Care organizations at Thanjavur. Thirty-two fully completed questionnaires were received.
Living in 21st century in itself reminds all of us the necessity of police and its administration. As more and more we are entering into the modern society and culture, the more we require the services of the so called ‘Khaki Worthy’ men i.e., the police personnel. Whether we talk of Indian police or the other nation’s police, they all have the same recognition as they have in India. But as already mentioned, their services and requirements are different after the like 26th November, 2008 incidents, where they without saving their own lives has sacrificed themselves without any hitch and without caring about their respective family members and wards. In other words, they are like our heroes and mentors who can guide us from the darkness of fear, militancy, corruption and other dark sides of life and so on. Now the question arises, if Gandhi would have been alive today, what would have been his reaction/opinion to the police and its functioning? Would he have some thing different in his mind now what he had been in his mind before the partition or would he be going to start some Satyagraha in the form of some improvement in the functioning of the police administration? Really these questions or rather night mares can come to any one’s mind, when there is too much confusion is prevailing in our minds, when there is too much corruption in the society and when the polices working is also in the questioning because of one or the other case throughout the India. It is matter of great concern that we have to thing over our administration and our practical approach because the police personals are also like us, they are part and parcel of our society and among one of us, so why we all are pin pointing towards them.
A STUDY ON TALENT MANAGEMENT AND ITS IMPACT ON EMPLOYEE RETENTION IN SELECTED...IAEME Publication
The goal of this study was to see how talent management affected employee retention in the selected IT organizations in Chennai. The fundamental issue was the difficulty to attract, hire, and retain talented personnel who perform well and the gap between supply and demand of talent acquisition and retaining them within the firms. The study's main goals were to determine the impact of talent management on employee retention in IT companies in Chennai, investigate talent management strategies that IT companies could use to improve talent acquisition, performance management, career planning and formulate retention strategies that the IT firms could use. The respondents were given a structured close-ended questionnaire with the 5 Point Likert Scale as part of the study's quantitative research design. The target population consisted of 289 IT professionals. The questionnaires were distributed and collected by the researcher directly. The Statistical Package for Social Sciences (SPSS) was used to collect and analyse the questionnaire responses. Hypotheses that were formulated for the various areas of the study were tested using a variety of statistical tests. The key findings of the study suggested that talent management had an impact on employee retention. The studies also found that there is a clear link between the implementation of talent management and retention measures. Management should provide enough training and development for employees, clarify job responsibilities, provide adequate remuneration packages, and recognise employees for exceptional performance.
ATTRITION IN THE IT INDUSTRY DURING COVID-19 PANDEMIC: LINKING EMOTIONAL INTE...IAEME Publication
Globally, Millions of dollars were spent by the organizations for employing skilled Information Technology (IT) professionals. It is costly to replace unskilled employees with IT professionals possessing technical skills and competencies that aid in interconnecting the business processes. The organization’s employment tactics were forced to alter by globalization along with technological innovations as they consistently diminish to remain lean, outsource to concentrate on core competencies along with restructuring/reallocate personnel to gather efficiency. As other jobs, organizations or professions have become reasonably more appropriate in a shifting employment landscape, the above alterations trigger both involuntary as well as voluntary turnover. The employee view on jobs is also afflicted by the COVID-19 pandemic along with the employee-driven labour market. So, having effective strategies is necessary to tackle the withdrawal rate of employees. By associating Emotional Intelligence (EI) along with Talent Management (TM) in the IT industry, the rise in attrition rate was analyzed in this study. Only 303 respondents were collected out of 350 participants to whom questionnaires were distributed. From the employees of IT organizations located in Bangalore (India), the data were congregated. A simple random sampling methodology was employed to congregate data as of the respondents. Generating the hypothesis along with testing is eventuated. The effect of EI and TM along with regression analysis between TM and EI was analyzed. The outcomes indicated that employee and Organizational Performance (OP) were elevated by effective EI along with TM.
INFLUENCE OF TALENT MANAGEMENT PRACTICES ON ORGANIZATIONAL PERFORMANCE A STUD...IAEME Publication
By implementing talent management strategy, organizations would have the option to retain their skilled professionals while additionally working on their overall performance. It is the course of appropriately utilizing the ideal individuals, setting them up for future top positions, exploring and dealing with their performance, and holding them back from leaving the organization. It is employee performance that determines the success of every organization. The firm quickly obtains an upper hand over its rivals in the event that its employees having particular skills that cannot be duplicated by the competitors. Thus, firms are centred on creating successful talent management practices and processes to deal with the unique human resources. Firms are additionally endeavouring to keep their top/key staff since on the off chance that they leave; the whole store of information leaves the firm's hands. The study's objective was to determine the impact of talent management on organizational performance among the selected IT organizations in Chennai. The study recommends that talent management limitedly affects performance. On the off chance that this talent is appropriately management and implemented properly, organizations might benefit as much as possible from their maintained assets to support development and productivity, both monetarily and non-monetarily.
A STUDY OF VARIOUS TYPES OF LOANS OF SELECTED PUBLIC AND PRIVATE SECTOR BANKS...IAEME Publication
Banking regulations act of India, 1949 defines banking as “acceptance of deposits for the purpose of lending or investment from the public, repayment on demand or otherwise and withdrawable through cheques, drafts order or otherwise”, the major participants of the Indian financial system are commercial banks, the financial institution encompassing term lending institutions. Investments institutions, specialized financial institution and the state level development banks, non banking financial companies (NBFC) and other market intermediaries such has the stock brokers and money lenders are among the oldest of the certain variants of NBFC and the oldest market participants. The asset quality of banks is one of the most important indicators of their financial health. The Indian banking sector has been facing severe problems of increasing Non- Performing Assets (NPAs). The NPAs growth directly and indirectly affects the quality of assets and profitability of banks. It also shows the efficiency of banks credit risk management and the recovery effectiveness. NPA do not generate any income, whereas, the bank is required to make provisions for such as assets that why is a double edge weapon. This paper outlines the concept of quality of bank loans of different types like Housing, Agriculture and MSME loans in state Haryana of selected public and private sector banks. This study is highlighting problems associated with the role of commercial bank in financing Small and Medium Scale Enterprises (SME). The overall objective of the research was to assess the effect of the financing provisions existing for the setting up and operations of MSMEs in the country and to generate recommendations for more robust financing mechanisms for successful operation of the MSMEs, in turn understanding the impact of MSME loans on financial institutions due to NPA. There are many research conducted on the topic of Non- Performing Assets (NPA) Management, concerning particular bank, comparative study of public and private banks etc. In this paper the researcher is considering the aggregate data of selected public sector and private sector banks and attempts to compare the NPA of Housing, Agriculture and MSME loans in state Haryana of public and private sector banks. The tools used in the study are average and Anova test and variance. The findings reveal that NPA is common problem for both public and private sector banks and is associated with all types of loans either that is housing loans, agriculture loans and loans to SMES. NPAs of both public and private sector banks show the increasing trend. In 2010-11 GNPA of public and private sector were at same level it was 2% but after 2010-11 it increased in many fold and at present there is GNPA in some more than 15%. It shows the dark area of Indian banking sector.
EXPERIMENTAL STUDY OF MECHANICAL AND TRIBOLOGICAL RELATION OF NYLON/BaSO4 POL...IAEME Publication
An experiment conducted in this study found that BaSO4 changed Nylon 6's mechanical properties. By changing the weight ratios, BaSO4 was used to make Nylon 6. This Researcher looked into how hard Nylon-6/BaSO4 composites are and how well they wear. Experiments were done based on Taguchi design L9. Nylon-6/BaSO4 composites can be tested for their hardness number using a Rockwell hardness testing apparatus. On Nylon/BaSO4, the wear behavior was measured by a wear monitor, pinon-disc friction by varying reinforcement, sliding speed, and sliding distance, and the microstructure of the crack surfaces was observed by SEM. This study provides significant contributions to ultimate strength by increasing BaSO4 content up to 16% in the composites, and sliding speed contributes 72.45% to the wear rate
ROLE OF SOCIAL ENTREPRENEURSHIP IN RURAL DEVELOPMENT OF INDIA - PROBLEMS AND ...IAEME Publication
The majority of the population in India lives in villages. The village is the back bone of the country. Village or rural industries play an important role in the national economy, particularly in the rural development. Developing the rural economy is one of the key indicators towards a country’s success. Whether it be the need to look after the welfare of the farmers or invest in rural infrastructure, Governments have to ensure that rural development isn’t compromised. The economic development of our country largely depends on the progress of rural areas and the standard of living of rural masses. Village or rural industries play an important role in the national economy, particularly in the rural development. Rural entrepreneurship is based on stimulating local entrepreneurial talent and the subsequent growth of indigenous enterprises. It recognizes opportunity in the rural areas and accelerates a unique blend of resources either inside or outside of agriculture. Rural entrepreneurship brings an economic value to the rural sector by creating new methods of production, new markets, new products and generate employment opportunities thereby ensuring continuous rural development. Social Entrepreneurship has the direct and primary objective of serving the society along with the earning profits. So, social entrepreneurship is different from the economic entrepreneurship as its basic objective is not to earn profits but for providing innovative solutions to meet the society needs which are not taken care by majority of the entrepreneurs as they are in the business for profit making as a sole objective. So, the Social Entrepreneurs have the huge growth potential particularly in the developing countries like India where we have huge societal disparities in terms of the financial positions of the population. Still 22 percent of the Indian population is below the poverty line and also there is disparity among the rural & urban population in terms of families living under BPL. 25.7 percent of the rural population & 13.7 percent of the urban population is under BPL which clearly shows the disparity of the poor people in the rural and urban areas. The need to develop social entrepreneurship in agriculture is dictated by a large number of social problems. Such problems include low living standards, unemployment, and social tension. The reasons that led to the emergence of the practice of social entrepreneurship are the above factors. The research problem lays upon disclosing the importance of role of social entrepreneurship in rural development of India. The paper the tendencies of social entrepreneurship in India, to present successful examples of such business for providing recommendations how to improve situation in rural areas in terms of social entrepreneurship development. Indian government has made some steps towards development of social enterprises, social entrepreneurship, and social in- novation, but a lot remains to be improved.
OPTIMAL RECONFIGURATION OF POWER DISTRIBUTION RADIAL NETWORK USING HYBRID MET...IAEME Publication
Distribution system is a critical link between the electric power distributor and the consumers. Most of the distribution networks commonly used by the electric utility is the radial distribution network. However in this type of network, it has technical issues such as enormous power losses which affect the quality of the supply. Nowadays, the introduction of Distributed Generation (DG) units in the system help improve and support the voltage profile of the network as well as the performance of the system components through power loss mitigation. In this study network reconfiguration was done using two meta-heuristic algorithms Particle Swarm Optimization and Gravitational Search Algorithm (PSO-GSA) to enhance power quality and voltage profile in the system when simultaneously applied with the DG units. Backward/Forward Sweep Method was used in the load flow analysis and simulated using the MATLAB program. Five cases were considered in the Reconfiguration based on the contribution of DG units. The proposed method was tested using IEEE 33 bus system. Based on the results, there was a voltage profile improvement in the system from 0.9038 p.u. to 0.9594 p.u.. The integration of DG in the network also reduced power losses from 210.98 kW to 69.3963 kW. Simulated results are drawn to show the performance of each case.
APPLICATION OF FRUGAL APPROACH FOR PRODUCTIVITY IMPROVEMENT - A CASE STUDY OF...IAEME Publication
Manufacturing industries have witnessed an outburst in productivity. For productivity improvement manufacturing industries are taking various initiatives by using lean tools and techniques. However, in different manufacturing industries, frugal approach is applied in product design and services as a tool for improvement. Frugal approach contributed to prove less is more and seems indirectly contributing to improve productivity. Hence, there is need to understand status of frugal approach application in manufacturing industries. All manufacturing industries are trying hard and putting continuous efforts for competitive existence. For productivity improvements, manufacturing industries are coming up with different effective and efficient solutions in manufacturing processes and operations. To overcome current challenges, manufacturing industries have started using frugal approach in product design and services. For this study, methodology adopted with both primary and secondary sources of data. For primary source interview and observation technique is used and for secondary source review has done based on available literatures in website, printed magazines, manual etc. An attempt has made for understanding application of frugal approach with the study of manufacturing industry project. Manufacturing industry selected for this project study is Mahindra and Mahindra Ltd. This paper will help researcher to find the connections between the two concepts productivity improvement and frugal approach. This paper will help to understand significance of frugal approach for productivity improvement in manufacturing industry. This will also help to understand current scenario of frugal approach in manufacturing industry. In manufacturing industries various process are involved to deliver the final product. In the process of converting input in to output through manufacturing process productivity plays very critical role. Hence this study will help to evolve status of frugal approach in productivity improvement programme. The notion of frugal can be viewed as an approach towards productivity improvement in manufacturing industries.
A MULTIPLE – CHANNEL QUEUING MODELS ON FUZZY ENVIRONMENTIAEME Publication
In this paper, we investigated a queuing model of fuzzy environment-based a multiple channel queuing model (M/M/C) ( /FCFS) and study its performance under realistic conditions. It applies a nonagonal fuzzy number to analyse the relevant performance of a multiple channel queuing model (M/M/C) ( /FCFS). Based on the sub interval average ranking method for nonagonal fuzzy number, we convert fuzzy number to crisp one. Numerical results reveal that the efficiency of this method. Intuitively, the fuzzy environment adapts well to a multiple channel queuing models (M/M/C) ( /FCFS) are very well.
Saudi Arabia stands as a titan in the global energy landscape, renowned for its abundant oil and gas resources. It's the largest exporter of petroleum and holds some of the world's most significant reserves. Let's delve into the top 10 oil and gas projects shaping Saudi Arabia's energy future in 2024.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Final project report on grocery store management system..pdfKamal Acharya
In today’s fast-changing business environment, it’s extremely important to be able to respond to client needs in the most effective and timely manner. If your customers wish to see your business online and have instant access to your products or services.
Online Grocery Store is an e-commerce website, which retails various grocery products. This project allows viewing various products available enables registered users to purchase desired products instantly using Paytm, UPI payment processor (Instant Pay) and also can place order by using Cash on Delivery (Pay Later) option. This project provides an easy access to Administrators and Managers to view orders placed using Pay Later and Instant Pay options.
In order to develop an e-commerce website, a number of Technologies must be studied and understood. These include multi-tiered architecture, server and client-side scripting techniques, implementation technologies, programming language (such as PHP, HTML, CSS, JavaScript) and MySQL relational databases. This is a project with the objective to develop a basic website where a consumer is provided with a shopping cart website and also to know about the technologies used to develop such a website.
This document will discuss each of the underlying technologies to create and implement an e- commerce website.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.