Muhammed Fuad Rashid Petroleum Engineering Department at Koya University Heat and Mass Transfer Laboratory 2020

1. Erbil PolytechnicUniversity
Koya Technical Institute
Dep. Of Oil Technology
Control and Operation
Name of Experiment:
Temperature Measurements and Calibration
Supervised by: Mr. Haymen F. Fattah
Name: Goran Adnan Ali
Group: A
Date of Exp.:8/11/2017
Name of laboratory: Heat and Mass Transfer

2. Title Page number
Aim 2
Theory 2
Sketch 6
Discussion 7
Calculation 8

3. Aim:
Measuring the temperature by different methods and draw the
calibration curve with thermometer readings.
Theory and procedure:
1.Temperaturemeasurement using liquidthermometers:
In a glass thermometer, the relative expansion of a liquid to the
content of the bulb is measured. The majority of the liquid is in a
spherical or cylindrical-shaped bulb that forms the thermometers
actual sensing element (1), the bulb opens into the long thin glass
capillary tube (2). Practically all liquids can be used in thermometers
here a differentiation is made between wetting (Organic) and non-
wetting liquids (mercury) wetting liquids cause additional errors as
the temperature drop, an organic liquid must be colored so that it is
visible in the capillary tube and the reading of the temperature made
easier. Liquid containers for mercury are larger than for other liquids
due to the smaller coefficient of expansion.

4. 2. Temperature measurement using Bimetallic thermometers:
Bimetallic thermometers exploit the differential expansion of two
different materials to indicate the temperature, two or more layers of
different materials are rolled to gather, during the process different
shapes can be manufactured depending on the application, one end
of the sensor is firmly anchored the other is coupled to a
transmission gear or directly to a display device, contrary to rod type
thermometers bimetallic sensors have only a low capacity to
perform work, they are thus practically limited to a usage for
indicating equipment and are less suitable for remote indication.
Over wide measuring ranges the non-linear relationship of the
specific deflection to temperature becomes detrimentally apparent
due to the relatively large surface areas. Bimetallic thermometers
that are exposed to the surrounding medium without heavy
protective housings react comparatively quickly.

5. 3. temperature measurement using Gas thermometers:
The thermodynamic temperature scale forms the theoretical basis of
thermometry. As the scale is very involved to reproduce, a number
of fixed points are defined for use in the engineering measurement
filed, these are considerable easier to depict, the gas thermometer is
one the most important devises used to relies the thermodynamic
temperature scale over a very wide temperature range almost down
to absolute zero, using this
method, the change in the pressure or volume of a gas is measured as
a function of temperature in accordance with the ideal gas equation:
P.V=M.R.T
Here the mass (M) and the gas constant rare constant, all
approximately ideal gases can be used (helium, nitrogen, argon).
The lowest measurable temperature is just above the critical points
of the respective charge gas (nitrogen -147°C).

6. Sketch:
35
40
45
50
55
60
65
70
75
80
85
90
95
100
105
110
115
120
125
0 3 6 9 12 15 18 21 24 27
Temperature
°C
Time in minute
refrence temperator liquid thermometer(non organic)
liquid thermometer (mercury) bimetallic thermometer
gas thermometer

7. Discussion:
1.Why we get different reading between all the
thermometers types?
A/because they are made of a different material to a special state
2.Whichthermometer is the best and has minimum
reading error?
A/gas thermometer
3.Why we have errors?
A/maybe we didn’t serious and fussy about readings of
thermometer, the atmospheric temperatureand pressure was
affected on our experiment.
4.Discussionthe diagram that you draw it?
A/ By increasing the time, the temperaturewill increase.
5.Whatyou suggest to gate a bitter reading?
A/ I think it’s much better if we connect our machine to a
programmed computerthat could do whole work and do all
commands that refers to our experiment test.