SUPERCAP FAST is a cement-based, self-leveling underlayment that develops high early strength. It can be applied over concrete, wood, and other rigid flooring substrates 1 day to 5 days before installing flooring. SUPERCAP FAST has advantages like early walkability within 2-4 hours, ability to install flooring after 1 day at 1/4" thickness, and contributing no mold growth. It has high compressive and bond strengths according to tests. The document provides instructions on mixing and applying SUPERCAP FAST over various substrate types.
SUPERCAP is a cement-based, self-leveling underlayment used to finish and level concrete floors before installing flooring. It can be applied over concrete, wood, and other rigid subfloors 1/4 to 2 inches thick. SUPERCAP dries quickly and flooring can be installed in as little as 1-3 days. It helps create a smooth, level surface and eliminates the need for power troweling concrete.
SUPERCAP is a self-leveling cement product used to cap interior concrete surfaces from 1/8 to 1 1/2 inches thick. It can accept flooring installation in as little as 7 days and provides a smooth, level surface without the need for traditional finishing techniques like power troweling. SUPERCAP is moisture and damage resistant, walkable within hours, and can withstand construction traffic for up to a year before flooring installation. It applies over properly prepared concrete at least 3 days old with a moisture content of 95% or less.
Tekcem Supra is a cement-based binder that can be used to replace ordinary Portland cement in screeds. It allows for rapid setting and strength gain, enabling early foot traffic after 12 hours and application of floor finishes within 24 hours. Tekcem Supra must be mixed in the same way as a normal sand/cement screed, using suitable aggregates and water. It can be used for bonded, unbonded, or floating screeds for applications such as floor repair or where quick drying is needed for overlaying finishes.
Tekcem is a cement-based binder designed to replace ordinary Portland cement in screeds. It enables quicker drying and earlier application of floor coverings than standard screeds. Tekcem can be used to produce bonded, unbonded, and floating screeds for internal applications like over underfloor heating. It dries more quickly than traditional screeds, allowing light foot traffic after 12 hours and full drying in 7 days. Tekcem is mixed with sand and water in the same way as a standard screed but provides improved strength and drying performance.
SUPERCAPTM FAST is a self-leveling cement product that can be applied to concrete surfaces as soon as 3 days after pouring to provide a smooth, level finish up to 1.5 inches thick. It reaches a compressive strength of 5000 PSI within 24 hours, allowing for installation of flooring. The product fills voids and removes variations in concrete slabs to provide a smooth, dense surface suitable for applying finished floor goods such as carpeting, vinyl, and wood as soon as one day after application.
The document discusses various construction and repair chemicals. It describes 21 categories of chemicals including injecting grouts, rust converters, corrosion inhibitors, passivating coats, bonding coats, plasticizers, super plasticizers, shrinkage reducing compounds, self-flowing micro concrete, polymer/epoxies in repair mortar, quick setting compounds, retarders, curing compounds, shutter oils, floor hardeners, waterproofing compounds, air entraining agents, anti-carbonation protective coatings, protective coats for steel, acid resistance enhancers, and anchoring compounds. Each category lists several product examples and describes their chemical composition and applications.
A fully bonded waterproof coating based on polyurethane technology
Find out more about RIW Flexiseal typical uses and benefits here:
http://www.riw.co.uk/products/liquid-applied-systems/Flexiseal
Noble Drilling was experiencing high failure rates in threaded connections on oil drilling equipment due to galling and thread defects. They were using a traditional anti-seize paste that was being squeezed out under high torque loads, leading to metal-on-metal contact and seizing. Dow Corning recommended their Molykote P-37 anti-seize paste, which forms a durable lubricating film and adheres strongly to stainless steel. Testing showed an immediate 50% reduction in failures, as the paste withstands extreme loads and temperatures without squeezing out.
SUPERCAP is a cement-based, self-leveling underlayment used to finish and level concrete floors before installing flooring. It can be applied over concrete, wood, and other rigid subfloors 1/4 to 2 inches thick. SUPERCAP dries quickly and flooring can be installed in as little as 1-3 days. It helps create a smooth, level surface and eliminates the need for power troweling concrete.
SUPERCAP is a self-leveling cement product used to cap interior concrete surfaces from 1/8 to 1 1/2 inches thick. It can accept flooring installation in as little as 7 days and provides a smooth, level surface without the need for traditional finishing techniques like power troweling. SUPERCAP is moisture and damage resistant, walkable within hours, and can withstand construction traffic for up to a year before flooring installation. It applies over properly prepared concrete at least 3 days old with a moisture content of 95% or less.
Tekcem Supra is a cement-based binder that can be used to replace ordinary Portland cement in screeds. It allows for rapid setting and strength gain, enabling early foot traffic after 12 hours and application of floor finishes within 24 hours. Tekcem Supra must be mixed in the same way as a normal sand/cement screed, using suitable aggregates and water. It can be used for bonded, unbonded, or floating screeds for applications such as floor repair or where quick drying is needed for overlaying finishes.
Tekcem is a cement-based binder designed to replace ordinary Portland cement in screeds. It enables quicker drying and earlier application of floor coverings than standard screeds. Tekcem can be used to produce bonded, unbonded, and floating screeds for internal applications like over underfloor heating. It dries more quickly than traditional screeds, allowing light foot traffic after 12 hours and full drying in 7 days. Tekcem is mixed with sand and water in the same way as a standard screed but provides improved strength and drying performance.
SUPERCAPTM FAST is a self-leveling cement product that can be applied to concrete surfaces as soon as 3 days after pouring to provide a smooth, level finish up to 1.5 inches thick. It reaches a compressive strength of 5000 PSI within 24 hours, allowing for installation of flooring. The product fills voids and removes variations in concrete slabs to provide a smooth, dense surface suitable for applying finished floor goods such as carpeting, vinyl, and wood as soon as one day after application.
The document discusses various construction and repair chemicals. It describes 21 categories of chemicals including injecting grouts, rust converters, corrosion inhibitors, passivating coats, bonding coats, plasticizers, super plasticizers, shrinkage reducing compounds, self-flowing micro concrete, polymer/epoxies in repair mortar, quick setting compounds, retarders, curing compounds, shutter oils, floor hardeners, waterproofing compounds, air entraining agents, anti-carbonation protective coatings, protective coats for steel, acid resistance enhancers, and anchoring compounds. Each category lists several product examples and describes their chemical composition and applications.
A fully bonded waterproof coating based on polyurethane technology
Find out more about RIW Flexiseal typical uses and benefits here:
http://www.riw.co.uk/products/liquid-applied-systems/Flexiseal
Noble Drilling was experiencing high failure rates in threaded connections on oil drilling equipment due to galling and thread defects. They were using a traditional anti-seize paste that was being squeezed out under high torque loads, leading to metal-on-metal contact and seizing. Dow Corning recommended their Molykote P-37 anti-seize paste, which forms a durable lubricating film and adheres strongly to stainless steel. Testing showed an immediate 50% reduction in failures, as the paste withstands extreme loads and temperatures without squeezing out.
Screeds provide a vital layer in a floor that bonds the finish people see and walk across to the concrete substrate of the building’s construction.
If properly applied and maintained then most screeds need never be seen until the building comes to the end of its life and is dismantled. However failures in the planning, application, curing or drying processes can lead to later, potentially very costly, problems.
Read Flowcrete's whitepaper for an overview of the reasons for screed failure in both commercial and industrial environments, as well as an insight into screed failure avoidance and repair.
Novafast SE Asia has over 15 years of experience in composites design and manufacturing. They have capabilities across designing, engineering, and building composites from the molecular level up. Their resin products Novafast 1000 and 2000 have been engineered to provide durability, robustness, and tailored properties to meet chemical and mechanical specifications. Novafast SE Asia works with clients in industries like oil and gas, mining, and infrastructure to design and supply composite products that meet application needs and standards.
Eclipse Shrinkage Reducing Admixture is a liquid admixture that can be added to concrete to dramatically reduce shrinkage due to drying by up to 80% at 28 days. It works by reducing the surface tension of water in pores between 2.5-50 nm in size, lessening the tensile forces that cause shrinkage. Adding Eclipse at 2% of cement weight is recommended to maximize shrinkage reduction of 25-50%. It has been shown to eliminate cracking from drying shrinkage in fully restrained concrete.
The PRESSURE-DRILL SF shrink-fit drilling riser uses a patented process to thermally shrink a flange onto pipe without welding, enabling use of materials that cannot be welded. This creates a high integrity pressure-rated connection through a mechanical interference fit and secondary locking mechanisms. The shrink-fit process can generate fatigue-resistant connections exceeding 15,000 psi in 24 hours using optimized assembly jigs. It preserves material properties, is insensitive to high temperatures, and eliminates weld qualification, improving schedules for applications like deepwater drilling risers.
FRP for masonry, stone, flat/curved arch terracotta and cindercrete stabilization with a Class A Fire Rating for interior, exterior, and above or below grade (wet) applications.
FAIRFLO 111 is high range water reducing agent and retarding admixture for concrete Conforming to conforming to ASTM C- 494 type 'F' & 'G' and IS 9103-1999. It has been primarily developed for application in the premixed and precast concrete industries where the highest durability and performance is required. It is a particularly strong super plasticizer allowing production of consistence concrete properties around the required dosage. It differentiated from conventional super plasticizer in that it is based on a special polymer with long lateral chain.
The document discusses the use of SAFPLANK® fiberglass plank systems at the Shatin Treatment Works in Hong Kong. SAFPLANK® planks were chosen to cover numerous open-topped tanks at the facility, which serves as both a water treatment plant and visiting area. The corrosion-resistant planks provide a safe walking surface and prevent algae growth, offering a more cost-effective solution than alternatives like aluminum or steel that require more maintenance.
Fairscreed R is a three-part epoxy repair mortar that can be used to repair damaged concrete structures like columns, floors, and roads. It has high early strength, is abrasion and impact resistant, and bonds well to cementitious surfaces primed with SafeCore Primer. The product is supplied in 7.5 kg packs that will cover 0.75 square meters at a 10mm thickness and can be applied between 10 to 40 degrees Celsius.
Chemicals used in construction general studies Aditya Sanyal
The document discusses the role of chemicals in the construction industry, focusing on corrosion inhibitors and superplasticizers. It provides an overview of how corrosion inhibitors and superplasticizers improve concrete properties like workability and durability. It also describes CSIR-SERC's research on corrosion inhibitor and superplasticizer performance, including fabric reinforced concrete. The document outlines techniques for evaluating inhibitor efficiency and assessing corrosion in reinforced concrete structures.
CTEP - UNIT - I - ADMIXTURES & CONSTRUCTION CHEMICALSShankar Ramasamy
This document provides information on concrete admixtures, including definitions and uses. It discusses different types of admixtures such as air-entraining agents, water reducers, plasticizers, superplasticizers, retarders, accelerators, and damp proofing admixtures. For each type of admixture, the document outlines their properties, mechanisms, advantages, and applications in concrete mixing and construction. In addition, the document covers curing compounds and polymer bonding agents used for curing concrete and bonding new concrete to existing structures.
The document provides information on Permaseal plug valves, including their design, construction, pressure relief features, and variety of body designs, end connections, materials, and accessory options. Key details include their tapered plug and double seat seal design, pressure relief hole for flushing, external seat wear indicator, wiping action to prevent material buildup, top entry for easy maintenance, and low torque allowing smaller actuators. A variety of end connections, materials, and accessories are available to meet application needs.
This document discusses color permeable concrete pavement and trench covers that allow for water infiltration. It notes that traditional pavement is impermeable and prevents the ground from absorbing water, which can lead to urban heat island effects and flooding. Permeable materials improve the ground's infiltration abilities. The document provides examples of permeable concrete projects in Taiwan and describes the construction methods and benefits of permeable pavement and covers, which include improving ecology, reducing flooding, lowering infrastructure costs, and decreasing energy usage.
Dampfix EG is an acrylic-based skim coat plaster designed to provide a smooth surface for painting on interior and exterior walls. It controls dampness and salt migration while allowing walls to dry naturally. It sands and applies easily, adheres well to surfaces, and has insulating properties that reduce condensation and mold growth. Dampfix EG is breathable and suitable for renovating damp or salt-contaminated walls.
FAIRFLO SCA is a differentiated from conventional superplasticisers in that it is based on a unique carboxylic ether polymer with long lateral chains. This greatly inproves cement dispersion. At the start on the mixing process an electrostatic dispersion occurs but the cement particles capacity to separe and disperse. This mechanism considerably reduces the water dement in flowable concrete. FAIRFLO SCA combines the properties of water reduction and workability retention. It allows the production of high performance concrete and / or concrete with high workability. FAIRFLO SCA is particularly strong superplasticiser allowing production of consistent concrete properties around the required dosage.
This document discusses good construction practices related to concrete, brickwork, mortar, plastering and surface preparation. Some key points discussed include:
- Curing of concrete is important for strength and durability and should be done for the entire curing period.
- Mortar plays a crucial role in bonding masonry units together and sealing the structure. Factors like bonding strength, workability and curing conditions affect mortar properties.
- Proper surface preparation like hacking, applying a spatter dash or wetting absorptive surfaces is important for achieving a good bond between plaster and the substrate.
The document discusses various construction materials including mortar, concrete, bitumen, and paints. It provides details on the composition and uses of different types of mortar such as lime mortar, cement mortar, and lime-cement mortar. It also discusses the main types of concrete including reinforced cement concrete. The document defines bitumen as a semi-solid hydrocarbon product derived from crude oil and lists its uses. Finally, it provides a basic definition of paint and some common uses such as artwork, decoration, surface protection, and warnings.
This document discusses the use of concrete admixtures and their benefits. It describes several types of admixtures including air entrainers, water reducers, set retarders, accelerators, superplasticizers, and specialty admixtures. It provides details on how each type of admixture improves properties such as durability, strength, permeability, workability, pumpability, and curing. Specific admixtures are highlighted for their ability to increase freeze-thaw resistance, reduce water content, enhance strength development, reduce corrosion, and control setting time. A variety of applications are presented where different admixtures provide advantages.
The document provides an overview of asphalt surfacing types and their application, covering basic asphalt principles like mix design and production, the uses and types of asphalt including dense graded asphalt and stone mastic asphalt, and guidance on treatment selection for different traffic and road conditions. The goal is to help participants develop an understanding of asphalt design, practice, and selection of the appropriate surfacing type.
The document discusses Ardex 'Rapidry Formula' cement systems for flooring. It describes how products with the Rapidry Formula logo incorporate unique technology allowing them to totally bind water during mixing. This enables rapid hardening and drying of screeds and toppings regardless of thickness. It also eliminates the risk of discoloration when fixing natural stone. Several Ardex cement products are then described including screeds, self-leveling compounds, primers, and a car park system.
The document provides details about the construction of the CC-27 metro corridor project in Delhi. It discusses the proposed route, construction methods used at different stations, specifications of materials like concrete mixes, and repair works. The bottom-up construction approach is used at Vasant Vihar due to hard rock, while soft soil at Hauz Khas uses a top-down method. Waterproofing involves applying a two-component polyurethane coating after priming and adding aggregates to the primer layer.
Screeds provide a vital layer in a floor that bonds the finish people see and walk across to the concrete substrate of the building’s construction.
If properly applied and maintained then most screeds need never be seen until the building comes to the end of its life and is dismantled. However failures in the planning, application, curing or drying processes can lead to later, potentially very costly, problems.
Read Flowcrete's whitepaper for an overview of the reasons for screed failure in both commercial and industrial environments, as well as an insight into screed failure avoidance and repair.
Novafast SE Asia has over 15 years of experience in composites design and manufacturing. They have capabilities across designing, engineering, and building composites from the molecular level up. Their resin products Novafast 1000 and 2000 have been engineered to provide durability, robustness, and tailored properties to meet chemical and mechanical specifications. Novafast SE Asia works with clients in industries like oil and gas, mining, and infrastructure to design and supply composite products that meet application needs and standards.
Eclipse Shrinkage Reducing Admixture is a liquid admixture that can be added to concrete to dramatically reduce shrinkage due to drying by up to 80% at 28 days. It works by reducing the surface tension of water in pores between 2.5-50 nm in size, lessening the tensile forces that cause shrinkage. Adding Eclipse at 2% of cement weight is recommended to maximize shrinkage reduction of 25-50%. It has been shown to eliminate cracking from drying shrinkage in fully restrained concrete.
The PRESSURE-DRILL SF shrink-fit drilling riser uses a patented process to thermally shrink a flange onto pipe without welding, enabling use of materials that cannot be welded. This creates a high integrity pressure-rated connection through a mechanical interference fit and secondary locking mechanisms. The shrink-fit process can generate fatigue-resistant connections exceeding 15,000 psi in 24 hours using optimized assembly jigs. It preserves material properties, is insensitive to high temperatures, and eliminates weld qualification, improving schedules for applications like deepwater drilling risers.
FRP for masonry, stone, flat/curved arch terracotta and cindercrete stabilization with a Class A Fire Rating for interior, exterior, and above or below grade (wet) applications.
FAIRFLO 111 is high range water reducing agent and retarding admixture for concrete Conforming to conforming to ASTM C- 494 type 'F' & 'G' and IS 9103-1999. It has been primarily developed for application in the premixed and precast concrete industries where the highest durability and performance is required. It is a particularly strong super plasticizer allowing production of consistence concrete properties around the required dosage. It differentiated from conventional super plasticizer in that it is based on a special polymer with long lateral chain.
The document discusses the use of SAFPLANK® fiberglass plank systems at the Shatin Treatment Works in Hong Kong. SAFPLANK® planks were chosen to cover numerous open-topped tanks at the facility, which serves as both a water treatment plant and visiting area. The corrosion-resistant planks provide a safe walking surface and prevent algae growth, offering a more cost-effective solution than alternatives like aluminum or steel that require more maintenance.
Fairscreed R is a three-part epoxy repair mortar that can be used to repair damaged concrete structures like columns, floors, and roads. It has high early strength, is abrasion and impact resistant, and bonds well to cementitious surfaces primed with SafeCore Primer. The product is supplied in 7.5 kg packs that will cover 0.75 square meters at a 10mm thickness and can be applied between 10 to 40 degrees Celsius.
Chemicals used in construction general studies Aditya Sanyal
The document discusses the role of chemicals in the construction industry, focusing on corrosion inhibitors and superplasticizers. It provides an overview of how corrosion inhibitors and superplasticizers improve concrete properties like workability and durability. It also describes CSIR-SERC's research on corrosion inhibitor and superplasticizer performance, including fabric reinforced concrete. The document outlines techniques for evaluating inhibitor efficiency and assessing corrosion in reinforced concrete structures.
CTEP - UNIT - I - ADMIXTURES & CONSTRUCTION CHEMICALSShankar Ramasamy
This document provides information on concrete admixtures, including definitions and uses. It discusses different types of admixtures such as air-entraining agents, water reducers, plasticizers, superplasticizers, retarders, accelerators, and damp proofing admixtures. For each type of admixture, the document outlines their properties, mechanisms, advantages, and applications in concrete mixing and construction. In addition, the document covers curing compounds and polymer bonding agents used for curing concrete and bonding new concrete to existing structures.
The document provides information on Permaseal plug valves, including their design, construction, pressure relief features, and variety of body designs, end connections, materials, and accessory options. Key details include their tapered plug and double seat seal design, pressure relief hole for flushing, external seat wear indicator, wiping action to prevent material buildup, top entry for easy maintenance, and low torque allowing smaller actuators. A variety of end connections, materials, and accessories are available to meet application needs.
This document discusses color permeable concrete pavement and trench covers that allow for water infiltration. It notes that traditional pavement is impermeable and prevents the ground from absorbing water, which can lead to urban heat island effects and flooding. Permeable materials improve the ground's infiltration abilities. The document provides examples of permeable concrete projects in Taiwan and describes the construction methods and benefits of permeable pavement and covers, which include improving ecology, reducing flooding, lowering infrastructure costs, and decreasing energy usage.
Dampfix EG is an acrylic-based skim coat plaster designed to provide a smooth surface for painting on interior and exterior walls. It controls dampness and salt migration while allowing walls to dry naturally. It sands and applies easily, adheres well to surfaces, and has insulating properties that reduce condensation and mold growth. Dampfix EG is breathable and suitable for renovating damp or salt-contaminated walls.
FAIRFLO SCA is a differentiated from conventional superplasticisers in that it is based on a unique carboxylic ether polymer with long lateral chains. This greatly inproves cement dispersion. At the start on the mixing process an electrostatic dispersion occurs but the cement particles capacity to separe and disperse. This mechanism considerably reduces the water dement in flowable concrete. FAIRFLO SCA combines the properties of water reduction and workability retention. It allows the production of high performance concrete and / or concrete with high workability. FAIRFLO SCA is particularly strong superplasticiser allowing production of consistent concrete properties around the required dosage.
This document discusses good construction practices related to concrete, brickwork, mortar, plastering and surface preparation. Some key points discussed include:
- Curing of concrete is important for strength and durability and should be done for the entire curing period.
- Mortar plays a crucial role in bonding masonry units together and sealing the structure. Factors like bonding strength, workability and curing conditions affect mortar properties.
- Proper surface preparation like hacking, applying a spatter dash or wetting absorptive surfaces is important for achieving a good bond between plaster and the substrate.
The document discusses various construction materials including mortar, concrete, bitumen, and paints. It provides details on the composition and uses of different types of mortar such as lime mortar, cement mortar, and lime-cement mortar. It also discusses the main types of concrete including reinforced cement concrete. The document defines bitumen as a semi-solid hydrocarbon product derived from crude oil and lists its uses. Finally, it provides a basic definition of paint and some common uses such as artwork, decoration, surface protection, and warnings.
This document discusses the use of concrete admixtures and their benefits. It describes several types of admixtures including air entrainers, water reducers, set retarders, accelerators, superplasticizers, and specialty admixtures. It provides details on how each type of admixture improves properties such as durability, strength, permeability, workability, pumpability, and curing. Specific admixtures are highlighted for their ability to increase freeze-thaw resistance, reduce water content, enhance strength development, reduce corrosion, and control setting time. A variety of applications are presented where different admixtures provide advantages.
The document provides an overview of asphalt surfacing types and their application, covering basic asphalt principles like mix design and production, the uses and types of asphalt including dense graded asphalt and stone mastic asphalt, and guidance on treatment selection for different traffic and road conditions. The goal is to help participants develop an understanding of asphalt design, practice, and selection of the appropriate surfacing type.
The document discusses Ardex 'Rapidry Formula' cement systems for flooring. It describes how products with the Rapidry Formula logo incorporate unique technology allowing them to totally bind water during mixing. This enables rapid hardening and drying of screeds and toppings regardless of thickness. It also eliminates the risk of discoloration when fixing natural stone. Several Ardex cement products are then described including screeds, self-leveling compounds, primers, and a car park system.
The document provides details about the construction of the CC-27 metro corridor project in Delhi. It discusses the proposed route, construction methods used at different stations, specifications of materials like concrete mixes, and repair works. The bottom-up construction approach is used at Vasant Vihar due to hard rock, while soft soil at Hauz Khas uses a top-down method. Waterproofing involves applying a two-component polyurethane coating after priming and adding aggregates to the primer layer.
Sika Latex is a synthetic rubber emulsion that improves the qualities of cement mortars used in applications such as patching, renders, screeds, repairs, and tile fixing. It provides good adhesion, flexibility, water resistance, abrasion resistance, and chemical resistance when added to mixing water. It does not re-emulsify under alkaline conditions. Mix designs are provided for bonding slurries, repair mortars, flooring mortars, and grouts using Sika Latex with cement, sand, water and optional admixtures. Proper substrate preparation, application procedures, curing and health and safety measures are also described.
Nitoproof RS is an acrylic waterproofing membrane that can be applied by brush, roller, or sprayer to roofs, gutters, and other structures. It provides long-term protection against water and weathering. It is flexible, resistant to chemicals and UV rays, and allows structures to dry out naturally. Nitoproof RS has excellent adhesion and can bridge cracks up to 5mm. It is easy to apply and offers cost-effective protection for roofs and structures.
This document provides information on UltraTech Cement's building products division and their product portfolio. It discusses their various cement-based products including AAC blocks, waterproofing solutions, tile adhesives, floor screeds, plasters, industrial grouts, and mortars. It provides details on the product segments, locations of BPD plants, technical specifications and parameters of their mortar and plaster range, and waterproofing solutions like Seal & Dry SBR and Weather Pro WP+. It also summarizes the uses and application areas of these products for construction purposes like plastering, tiling, waterproofing of structures.
Polytek Moisture Sealing Epoxy Primer is a two-component, 100% solids epoxy primer that reduces hydrostatic pressure in concrete from 12 lbs to less than 1 lb per 1000 square feet. It can cure underwater without affecting adhesion and cures in 6-7 hours at 73°F and 50% humidity. The primer is used to seal concrete, metal, and wood substrates and provides high adhesion and build with zero VOCs. It requires a clean, dry substrate with less than 80% relative humidity and pH between 5-9 for proper adhesion.
Polytek Premium Floor Coating Epoxy is a two-component, 100% solids, high-build, low viscosity, low
odor, modified cycloaliphatic, chemical resistant epoxy. This highly versatile epoxy coating comes in both clear and a variety
of pigmented colors. It can be used as a primer (when vapor emission is below 4.5lbs/1000 ft²/24hr), a base coat, or as a
topcoat.
RIW Structureseal -Sodium Bentonite System - Typical DetailsRIW Ltd
Structureseal is a waterproofing composite made of a geotextile encapsulating sodium bentonite. It is a pre-applied tanking system that is quick and easy to apply without primers or adhesives. It can waterproof below-grade structures like basements, retaining walls, and ground floors when applied to surfaces like concrete, compacted earth, and sand blinding. When wetted, the sodium bentonite within Structureseal can swell up to 15 times its dry volume to self-seal cracks and form an impervious barrier against water for the life of the structure. Typical applications include backfilled concrete walls, slabs on grade, and various boundary line construction methods.
Aquaurethane Extreme - Regulation 31 Approved Polyurea by LINE-XDarren Hull
PRODUCT USE DESCRIPTION
LINE-X Aquaurethane Extreme is designed to be used to coat existing substrates that have become porous. For example, by coating the external concrete surface of underground reservoirs that are starting to leak you will be able to prevent untreated rainwater from leaking into the reservoirs. This product can also be used to line the internal walls of the reservoirs to prevent the water from leaking out into the groundwater whilst also preventing the groundwater from penetrating the sidewalls into the drinking water.
Aquaurethane Extreme is Regulation 31 Approved.
Find out more by visiting https://line-x.co.uk/heavy-industrial/aquaurethane-extreme/
Learn everything about car park protection at http://marispolymers.com/products/flooring-systems/waterproofing-car-parking-flooring-systems/
Maris polyurethane products offer great car park protection. Highly permanent elastic membranes with excellent mechanical,thermal and UV resistance properties.
JBA Concrete Solutions Pvt. Ltd. is a leading company specializes in providing New-Age Concrete Solutions across India. JBA offers a complete assortment of high-performance floor solutions for the protection and beautification of Industrial, Institutional, Residential, and Office Concrete floors. We would like to introduce ourselves that we are providing Concrete Solutions based on 3Rs concepts that are Repair, Restorations, and Rehabilitation of Concrete since last more than two decades now.
We wish to introduce to you:-
Ashford Formula (The Densification Concept)
Retroplate System (Concrete Polishing and Restoring System)
Rapid Set® Cement All (Repair and Grouting)
Concrete Dyes (An art you can walk on)
PNA Dowel System (For Construction Joints)
PNA Hydra Cure Covers (Reduce Discoloration and Residue on your Slabs)
MM-80 (Heavy Duty Epoxy Joint Filler)
Grass Crete (To grow grass in RCC Pockets)
HYCRETE – for water Resistance Concrete
We have done over 100 million SFT of concrete floor treatment in India. To name a few references – DMRC, Jaipur Metro, BMRCL, Jotun paints, AUDI, BMW, 3M India, TAFE, Force Motors, FORD, DAIMLER, General Motors, Bajaj, Apollo Tyres, Ceat Tyres, Caparo, Bonfiglioli, Metro Cash & Carry, Dr. Reddys Laboratories, Parle Products, Kemwell, P&G, Cadbury, Ranbaxy, ZYDUS, COKE etc., had treated their floors using our state-of-the-art densification treatments.
This document provides installation instructions for Siena Recycled Rubber flooring. It outlines recommendations for job site conditions, subfloor preparation and requirements, material storage and handling, and installation methods. The installer should prepare subfloors according to specifications, maintain temperature and moisture conditions, and either glue down rolls using a polyurethane adhesive or tape seams of rolls using double-faced carpet tape. Rolling, hand-rolling, and taping seams ensures a tight installation. Installers should follow guidelines closely and contact the manufacturer with any questions.
Self-compacting concrete (SCC) is a highly flowable concrete that can spread into place and fill formwork without any mechanical consolidation. SCC was developed in Japan in the 1980s to overcome issues with inadequate consolidation of traditional vibrated concrete. SCC uses special admixtures and optimized aggregate gradation to achieve excellent flowability, passing ability, and segregation resistance. While SCC has higher material costs, it provides benefits of easier placement, improved quality, reduced labor requirements, and faster construction.
CRACKSEAL SUPER is an easy to use, prepacked high strength, fast setting crack repair mortar, which ensures perfect filling of cracks and will not allow water penetration.
Sikalastic-560 is a hybrid, economical and eco-friendly waterproofing solution based on Sika Co-Elastic Technology. It can be used for exposed waterproofing on roofs and for external waterproofing under tiles. The document provides instructions on substrate preparation, priming, application, drying times, and consumption rates for achieving various durations of waterproofing from 3 to 15 years. Sikalastic-560 offers benefits like high elasticity, crack bridging, color stability, faster drying, and environmental friendliness.
The document provides information on epoxy flooring systems, including their properties, installation process, and types of primers used. The installation process involves 4 steps: 1) substrate preparation, 2) substrate priming, 3) filling surface irregularities, and 4) final coating. Various epoxy and polyurethane primers are described that can be used depending on the substrate type and conditions.
The document discusses MYK LATICRETE, a leader in tile and stone installation solutions. It describes their factory in Hyderabad which manufactures a range of products using advanced R&D. These include screeds, waterproofing membranes, tile adhesives, grouts, and stone care products. The factory uses state-of-the-art facilities and R&D to develop innovative solutions and new eco-friendly products.
Sample Specification for M10 Proprietary Quick Drying Levelling ScreedsFlexiDry Global Ltd
This document discusses FlexiDry, a proprietary quick drying cementitious screed that can be used for bonded, unbonded, floating, and heated screeds. It comes in options to dry in 3, 7, 14, or 21 days. The document provides details on substrate preparation, screed construction, recommended thicknesses, finishes, joints, and curing. It emphasizes mixing and application should follow the manufacturer's recommendations to achieve the desired strength and drying properties.
Sample Specification for M10 Proprietary Quick Drying Levelling Screeds
Supercap fast tds english
1. Technical Data Sheet
Edition 08.2010
SUPERCAP™ FAST
TM SUPERCAP™ FAST
Advanced Self-Leveling Underlayment Technology
Description SUPERCAP FAST is a pumpable and pourable, cement-based, advanced self-leveling underlayment based on a
proprietary mineral binder system that develops high early strength and is used to finish concrete and level uneven
SUPERCAP
floor surfaces. Finished flooring can be installed quickly. Apply it over concrete, wood and other types of sound, rigid
flooring before installing wood, resilient, cork, sports, ceramic, stone, carpet or other flooring systems. Floor covering
adhesives that are suitable for concrete can be used on SUPERCAP FAST.
Where to Use Location: ▪ Interior
Substrates: ▪ Concrete
▪ Wood
▪ Rigid subflooring including VAT, VCT and ceramic tile
Applications: ▪ New concrete
▪ Deteriorated and uneven surfaces – deflection
▪ Restoration
Advantages • Eliminates the need for power troweling concrete.
• Can be installed over newly poured concrete as soon as five days after placement.
• Finished floor goods may be installed as soon as 1 day after application, subject to thickness, drying conditions and
type of flooring materials.
• Eligible for two (2) LEED® project points for regional materials.
• Low pH formulation allows for quick installation of finished floor goods.
• Water damage stable; will not deteriorate, warp, buckle, or change shape even when soaked or exposed to high
moisture conditions.
• Surface is walkable in 2-4 hours and may be open to wheel traffic within 24 hours.
• Can be left open to normal trade’s traffic for up to 1 year prior to installation of floor coverings.
• Inorganic formulation will not contribute to or harbor growth of mold or mildew.
• Will not contribute to secondary emissions or irritating fumes upon setting or curing.
Technical Data Typical Pour Depth ................................................................... ¼" to 2" (consult Technical Services for greater depths)
Coverage (sq. ft. @ ¼" per 50 lb. bag)....................................... 22 – 24*
Packaging ................................................................................. 50 lb bag, 45 bags per pallet | 2,500 lb Supersack
Walkable .................................................................................. 2-4 hours
Finished Floor Installation ........................................................ 1 day @ ¼" | 5 days @ ½" | 10 days @1" (72°F-50% RH)
Tensile Bond Strength (ASTM C 1583) ...................................... 28d: 350 psi
Flexural Strength (ASTM C 348) ................................................ 28d: 1000 psi
Compressive Strength (ASTM C 109M) ..................................... 1d: 2700 psi | 7d: 3,600 psi | 28d: 5,200 psi
Set Time (ASTM C191) .............................................................. Initial @ 60 min | Final @ 70 min
Flow (1¼" x 2" metal ring) ........................................................ 143 mm
Flow Retention ......................................................................... 150 mm @ 20 min | 150 mm @ 30 min
Wet Density.............................................................................. 131-133 lbs/ft³
Installed Dry Weight (per square foot @ ¼") ............................ 2.35-2.47 lbs/ft2
Shelf Life................................................................................... 6 mo from date of manufacture in unopened package
All test methods and procedures are described in “Testing Hydraulic Characteristics of SUPERCAP”; a document that is available upon request.
*Mix water demand may vary due to regional raw materials where SUPERCAP is manufactured and may cause slight variations in physical properties.
How to Use New Concrete Slabs: Bull float to FF of 12-15, adjust finished elevation by ⅝" for 2-course slab; curing compounds are
not recommended. New concrete should be allowed to cure for a minimum of 5 days prior to installation of SUPERCAP.
Concrete must be free from hydrostatic pressure.
Concrete Floors (general): Substrate must be well-bonded (ICRI Technical Guideline No. 03739) and completely clean;
free of oil, wax, grease, sealers, curing compounds, asphalt, paint, dirt, loose surface material and any contaminate that
will act as a bond-breaker. Surface bond strength of substrate should be minimum 100 psi (0.69 MPa). Weak concrete
surfaces must be cleaned down to solid sound concrete by mechanical means. Acid etching or chemical cleaning is not
acceptable. Expansion joints in the concrete substrate must be reflected through the applied layer SUPERCAP. Concrete
must be free from hydrostatic pressure. Fill deep areas and depressions with a SUPERCAP pre-fill or suitable cement-
based concrete repair product. Repair cracks with epoxy grout. Material will flow as water and will go anywhere water
will go (contact Product Technologies’ Technical Service Department for details).
Over Cutback and Adhesive Residue: Supercap can be installed over non-soluble adhesives residues such as Cutback.
Cutback adhesives may contain asbestos fibers whose inhalation resulting from sanding or grinding maybe harmful.
Thick accumulation, brittle, powdery residue or weak unbonded adhesive must be removed using the wet-scrape and
wet-sweep method as outlined in the Resilient Floor Covering Institute www.rfci.com booklet. Consult your local,
provincial and federal regulations before attempting to remove or dispose of hazardous material for further
instructions. Remaining residue needs to be translucent, clean and well bonded to the substrate readied for SUPERCAP
PRIMER. Installation over non-Cutback adhesives is possible provided the residue is solid, bonded to substrate and NOT
water soluble. Avoid applications where heat may soften the adhesive causing de-lamination.
Water Soluble Adhesive: Mechanically remove by shotblasting or other acceptable mechanical means leaving a
Concrete Surface Profile (ICRI CSP) 3-5. Other surface contaminates may also require mechanical removal.