Simply Supported Beam Examples | Mechanical Engineering
•Download as PPTX, PDF•
8 likes•10,526 views
If both the ends of a beam are supported by end supports then the beam is known as Simply Supported Beam. One end of the beam is supported by roller support and the other end is supported by a hinged or pinned support. Copy the link given below and paste it in new browser window to get more information on Simply Supported Beam Examples:- http://www.transtutors.com/homework-help/mechanical-engineering/bending-moment-and-shear-force/simply-supported-beam-examples.aspx
Report
Share
Report
Share
Recommended
Lecture 9 shear force and bending moment in beams
The document discusses stresses in beams. It covers topics like shear force and bending moment diagrams, bending stresses, shear stresses, deflection, and torsion. Beams are structural members subjected to transverse forces that induce bending. Stresses and strains are created within beams when loaded. Shear forces and bending moments allow determining these internal stresses and maintaining equilibrium. Formulas are provided for calculating shear forces and bending moments in different beam configurations like cantilevers, simply supported beams, and beams with various load types.
Bending stresses in beams
This document discusses bending stresses in beams. It defines simple or pure bending as when a beam experiences zero shear force and constant bending moment over a length. For simple bending, the stress distribution can be calculated using beam theory. The key points are:
- Bending stresses are introduced due to bending moments and are highest at the extreme fibers furthest from the neutral axis.
- The neutral axis experiences no bending stress and its location is defined by the centroidal axis of the beam cross-section.
- Bending stress is directly proportional to the distance from the neutral axis. The stress distribution follows σ = My/I, where M is the bending moment, y is the distance from neutral axis, and I is
Simply supported beams
simple supported beams with shear force and bending moments diagrams, different types of loading conditions, everyday scenarios of simply supported beams, advantages and disadvantages of simple supported beams
SFD BMD
This document discusses strength of materials concepts related to shear force diagrams (SFD) and bending moment diagrams (BMD) for beams. It defines key terms like shear force, bending moment, and point of contraflexure. It also explains how to draw SFDs and BMDs for different beam types under various loading conditions and the relationships between loading, shear force, and bending moment. Application of the diagrams to reinforcement design is also mentioned.
Bending stresses in beams
Bending Stresses are important in the design of beams from strength point of view. The present source gives an idea on theory and problems in bending stresses.
Specifications of steel
Steel is an alloy of iron and carbon, with small amounts of other elements like manganese, phosphorus, and silicon. Carbon content in common steel grades ranges from 0.1-1%. These alloying elements determine the properties of different steel types. Steels are classified as low alloy (<10% other elements) or high alloy, and can be further broken down by carbon content. Low carbon steels are commonly used and have good weldability and machinability but require cold working to strengthen. Alloying elements like manganese and phosphorus increase hardness and strength but decrease ductility.
Deflection
This document discusses beam design criteria and deflection behavior of beams. It covers two key criteria for beam design:
1) Strength criterion - the beam cross section must be strong enough to resist bending moments and shear forces.
2) Stiffness criterion - the maximum deflection of the beam cannot exceed a limit and the beam must be stiff enough to resist deflections from loading.
It then defines deflection, slope, elastic curve, and flexural rigidity. It presents the differential equation that relates bending moment, slope, and deflection. Methods for calculating slope and deflection including double integration, Macaulay's method, and others are also summarized.
footing
Footings are structural members that support columns and walls and transmit their loads to the soil. Different types of footings include wall footings, isolated/single footings, combined footings, cantilever/strap footings, continuous footings, rafted/mat foundations, and pile caps. Footings must be designed to safely carry and transmit loads to the soil while meeting code requirements regarding bearing capacity, settlement, reinforcement, and shear strength. A proper footing design involves determining loads, allowable soil pressure, reinforcement requirements, and assessing settlement.
Recommended
Lecture 9 shear force and bending moment in beams
The document discusses stresses in beams. It covers topics like shear force and bending moment diagrams, bending stresses, shear stresses, deflection, and torsion. Beams are structural members subjected to transverse forces that induce bending. Stresses and strains are created within beams when loaded. Shear forces and bending moments allow determining these internal stresses and maintaining equilibrium. Formulas are provided for calculating shear forces and bending moments in different beam configurations like cantilevers, simply supported beams, and beams with various load types.
Bending stresses in beams
This document discusses bending stresses in beams. It defines simple or pure bending as when a beam experiences zero shear force and constant bending moment over a length. For simple bending, the stress distribution can be calculated using beam theory. The key points are:
- Bending stresses are introduced due to bending moments and are highest at the extreme fibers furthest from the neutral axis.
- The neutral axis experiences no bending stress and its location is defined by the centroidal axis of the beam cross-section.
- Bending stress is directly proportional to the distance from the neutral axis. The stress distribution follows σ = My/I, where M is the bending moment, y is the distance from neutral axis, and I is
Simply supported beams
simple supported beams with shear force and bending moments diagrams, different types of loading conditions, everyday scenarios of simply supported beams, advantages and disadvantages of simple supported beams
SFD BMD
This document discusses strength of materials concepts related to shear force diagrams (SFD) and bending moment diagrams (BMD) for beams. It defines key terms like shear force, bending moment, and point of contraflexure. It also explains how to draw SFDs and BMDs for different beam types under various loading conditions and the relationships between loading, shear force, and bending moment. Application of the diagrams to reinforcement design is also mentioned.
Bending stresses in beams
Bending Stresses are important in the design of beams from strength point of view. The present source gives an idea on theory and problems in bending stresses.
Specifications of steel
Steel is an alloy of iron and carbon, with small amounts of other elements like manganese, phosphorus, and silicon. Carbon content in common steel grades ranges from 0.1-1%. These alloying elements determine the properties of different steel types. Steels are classified as low alloy (<10% other elements) or high alloy, and can be further broken down by carbon content. Low carbon steels are commonly used and have good weldability and machinability but require cold working to strengthen. Alloying elements like manganese and phosphorus increase hardness and strength but decrease ductility.
Deflection
This document discusses beam design criteria and deflection behavior of beams. It covers two key criteria for beam design:
1) Strength criterion - the beam cross section must be strong enough to resist bending moments and shear forces.
2) Stiffness criterion - the maximum deflection of the beam cannot exceed a limit and the beam must be stiff enough to resist deflections from loading.
It then defines deflection, slope, elastic curve, and flexural rigidity. It presents the differential equation that relates bending moment, slope, and deflection. Methods for calculating slope and deflection including double integration, Macaulay's method, and others are also summarized.
footing
Footings are structural members that support columns and walls and transmit their loads to the soil. Different types of footings include wall footings, isolated/single footings, combined footings, cantilever/strap footings, continuous footings, rafted/mat foundations, and pile caps. Footings must be designed to safely carry and transmit loads to the soil while meeting code requirements regarding bearing capacity, settlement, reinforcement, and shear strength. A proper footing design involves determining loads, allowable soil pressure, reinforcement requirements, and assessing settlement.
FLITCHED BEAMS
This document discusses flitched beams, which are composite beams made of wood beams sandwiched around a steel plate and held together with bolts. It defines beams and types of beams, then explains what composite beams and flitched beams are. It describes the design principle of flitched beams, which combines the properties of wood and steel to provide greater strength than either material alone. Applications of flitched beams include construction of houses and decks where they are stronger than wood but lighter than steel. However, engineered wood has replaced flitched beams due to lower costs and easier installation.
column and it's types
1. The document discusses reinforcement in concrete columns. It lists group members for a project and provides information on different types of columns, their load transfer mechanisms, and failure modes.
2. Key points covered include defining short, long, and intermediate columns based on their slenderness ratio. It also discusses calculating the effective length and radius of gyration of a column.
3. The document provides guidelines for steel reinforcement in columns, including minimum bar diameter and concrete cover, as well as the design procedure and considerations for selecting the reinforcement ratio.
Design of steel structure as per is 800(2007)
It does not offer resistance against rotation and also termed as a hinged or pinned connections.
It transfers only axial or shear forces and it is not designed for moment
It is generally connected by single bolt/rivet and therefore full rotation is allowed
Design of steel beams
This document provides an overview of the design of steel beams. It discusses various beam types and sections, loads on beams, design considerations for restrained and unrestrained beams. For restrained beams, it covers lateral restraint requirements, section classification, shear capacity, moment capacity under low and high shear, web bearing, buckling, and deflection checks. For unrestrained beams, it discusses lateral torsional buckling, moment and buckling resistance checks. Design procedures and equations for determining effective properties and capacities are also presented.
Connections in steel structures
Connections are critical components that join structural elements to transfer forces safely. Steel connections influence construction costs and failures often originate from connections. Common steel connections include bolted, welded, and riveted joints. Bolted connections can be bearing type or friction grip bolts. Welded joints include fillet and butt welds. Connections must be designed for the expected loads, with shear connections allowing rotation and moment connections resisting it. Proper connection design is important for structural integrity and economy.
Strength of materials_I
This document provides an introduction to strength of materials, including concepts of stress, strain, Hooke's law, stress-strain relationships, elastic constants, and factors of safety. It defines key terms like stress, strain, elastic limit, modulus of elasticity, and ductile and brittle material behavior. Examples of stress and strain calculations are provided for basic structural elements like rods, bars, and composite structures. The document also covers compound bars, principle of superposition, and effects of temperature changes.
Slabs Beam Reinforcement Detailing
This document provides problems and examples related to detailing of beams and slabs in reinforced concrete structures. It discusses concepts like continuous beams, cantilever beams, flanged beams, one-way slabs, and two-way slabs. Seven problems are presented involving drawing the longitudinal section and cross sections of beams and slabs and showing reinforcement details. The document concludes with two problems for the reader to solve involving preparing bar bending schedules and estimating quantities of steel and concrete.
Beams
OUTLINE
introduction
classification
loads
materials used
Type of reinforcement
RCC
construction methods in RCC
Analysis and design
Detailing
Basic Rules
Site visit
video
Types of beam & types of supports
This document discusses different types of beams and supports used in engineering mechanics. It describes four types of supports - fixed, simple, roller, and hinged - based on how they restrict the movement of beams. It also outlines six types of beams defined by their support conditions: fixed, cantilever, simply supported, overhanging, continuous, and combinations of these. Finally, it categorizes loads as point, uniformly distributed, or uniformly varying based on how forces are applied along the beam.
Columns
This document discusses different types of columns used in construction. It defines a column as a structural member subjected to compressive axial loads. Columns are classified as long, short, or intermediate based on their length-to-minimum radius of gyration ratio. Long columns have a ratio greater than 50, short columns less than 15-50, and intermediate between 30-100. The document provides examples of column types and discusses effective length, radius of gyration, buckling load, and Euler's formula for calculating crippling load.
Bending stresses
The document discusses bending stresses in beams. It describes how bending stresses are developed in beams to resist bending moments and shearing forces. The theory of pure bending is introduced, where only bending stresses are considered without the effect of shear. Equations for calculating bending stresses are derived based on the beam's moment of inertia, bending moment, and distance from the neutral axis. Several beam cross-section examples are provided to demonstrate how to calculate the maximum bending stress and section modulus.
Design of bolted connections
This document discusses types of bolt connections based on arrangement of bolts and plates, mode of load transmission, and nature and location of load. There are two main types of joints subjected to axial loads: lap joints and butt joints. Butt joints are preferable to lap joints because the load is split between members, eliminating eccentricity and bending. Bolt connections can fail due to shear, bearing, or tension failures of bolts or plates. The design strength of bolts is governed by their strength in shear, bearing, or tension with safety factors applied.
Design of R.C.C Beam
information on types of beams, different methods to calculate beam stress, design for shear, analysis for SRB flexure, design for flexure, Design procedure for doubly reinforced beam,
Beam ,Loads,Supports , trusses
The document discusses different types of structural elements used in building construction including beams, loads, supports, columns, and trusses. It describes several types of beams such as simply supported beams, continuous beams, overhanging beams, cantilever beams, and fixed beams. It also discusses different types of loads, supports, and how columns and trusses function structurally.
Beam Deflection Formulae
1. The document provides formulas for calculating slope, deflection, and maximum deflection for various beam types under different loading conditions. It gives the equations for cantilever beams with concentrated loads, uniformly distributed loads, and varying loads. It also provides the equations for simply supported beams with these different load types and with couple moments applied. The equations relate the beam properties like length, load location, and intensity to the resulting slope and deflection values.
Types of loads, beams, support and support reaction calculation
give information on:-
types of loads
types of beams
types of support
support reaction calculation
Reinforced column design
The document discusses reinforced concrete columns, including their functions, failure modes, classifications, and design considerations. Columns primarily resist axial compression but may also experience bending moments. They can fail due to compression, buckling, or a combination. Design depends on whether the column is short or slender, braced or unbraced. Reinforcement is designed based on the column's expected loads and dimensions using methods specified in design codes like BS 8110.
Shear stresses on beam (MECHANICS OF SOLIDS)
This document provides information about shear stresses and shear force in structures. It includes:
- Definitions of shear force and shear stress. Shear force is an unbalanced force parallel to a cross-section, and shear stress develops to resist the shear force.
- Explanations of horizontal and vertical shear stresses that develop in beams due to bending moments. Shear stress is highest at the neutral axis and reduces towards the top and bottom of the beam cross-section.
- Derivations of formulas for calculating shear stress across different beam cross-sections. Shear stress is directly proportional to the shear force and beam geometry.
- Examples of calculating maximum and average shear stresses for various cross-sections
Types of Beam Support | Mechanical Engineering
Beam is a structural member whose lateral dimensions are much smaller than the longitudinal dimension and used to carry loads perpendicular to the longitudinal axis. Copy the link given below and paste it in new browser window to get more information on Types of Beam Support:- http://www.transtutors.com/homework-help/mechanical-engineering/bending-moment-and-shear-force/types-of-beam-support.aspx
Design of combined footing ppt
The document discusses the design of a combined footing to support two columns. It first defines what a combined footing is and why it is used. It then describes the types of combined footings and the forces acting on it. The document provides the design steps for a rectangular combined footing, which include determining dimensions, reinforcement requirements, and design checks. As an example, it shows the detailed design of a rectangular combined footing supporting two columns with loads of 450kN and 650kN respectively. The design includes calculating dimensions, reinforcement, development lengths, and design checks.
Resultant of Coplanar Parallel Forces | Mechanical Engineering
If two or more than two forces are acting on a single plane then the forces are known as System of Coplanar Forces and if they are acting on different planes then the forces are called as Non-Coplanar Forces. Copy the link given below and paste it in new browser window to get more information on Resultant of Coplanar Parallel Forces:-
http://www.transtutors.com/homework-help/mechanical-engineering/force-systems-and-analysis/resultant-of-coplanar-parallel-forces.aspx
The Centroidal Axis | Mechanical Engineering
The force of attraction exerted by the earth on a solid body is known as Gravitational Force. It acts in a vertically downward direction and is known as weight of the body. Thus, the weight of the body is assumed to act at a point which is known as Centre of Gravity of a body. Copy the link given below and paste it in new browser window to get more information on The Centroidal Axis:-
http://www.transtutors.com/homework-help/mechanical-engineering/bending-stress/moment-of-inertia-about-the-centroidal-axis1.aspx
More Related Content
What's hot
FLITCHED BEAMS
This document discusses flitched beams, which are composite beams made of wood beams sandwiched around a steel plate and held together with bolts. It defines beams and types of beams, then explains what composite beams and flitched beams are. It describes the design principle of flitched beams, which combines the properties of wood and steel to provide greater strength than either material alone. Applications of flitched beams include construction of houses and decks where they are stronger than wood but lighter than steel. However, engineered wood has replaced flitched beams due to lower costs and easier installation.
column and it's types
1. The document discusses reinforcement in concrete columns. It lists group members for a project and provides information on different types of columns, their load transfer mechanisms, and failure modes.
2. Key points covered include defining short, long, and intermediate columns based on their slenderness ratio. It also discusses calculating the effective length and radius of gyration of a column.
3. The document provides guidelines for steel reinforcement in columns, including minimum bar diameter and concrete cover, as well as the design procedure and considerations for selecting the reinforcement ratio.
Design of steel structure as per is 800(2007)
It does not offer resistance against rotation and also termed as a hinged or pinned connections.
It transfers only axial or shear forces and it is not designed for moment
It is generally connected by single bolt/rivet and therefore full rotation is allowed
Design of steel beams
This document provides an overview of the design of steel beams. It discusses various beam types and sections, loads on beams, design considerations for restrained and unrestrained beams. For restrained beams, it covers lateral restraint requirements, section classification, shear capacity, moment capacity under low and high shear, web bearing, buckling, and deflection checks. For unrestrained beams, it discusses lateral torsional buckling, moment and buckling resistance checks. Design procedures and equations for determining effective properties and capacities are also presented.
Connections in steel structures
Connections are critical components that join structural elements to transfer forces safely. Steel connections influence construction costs and failures often originate from connections. Common steel connections include bolted, welded, and riveted joints. Bolted connections can be bearing type or friction grip bolts. Welded joints include fillet and butt welds. Connections must be designed for the expected loads, with shear connections allowing rotation and moment connections resisting it. Proper connection design is important for structural integrity and economy.
Strength of materials_I
This document provides an introduction to strength of materials, including concepts of stress, strain, Hooke's law, stress-strain relationships, elastic constants, and factors of safety. It defines key terms like stress, strain, elastic limit, modulus of elasticity, and ductile and brittle material behavior. Examples of stress and strain calculations are provided for basic structural elements like rods, bars, and composite structures. The document also covers compound bars, principle of superposition, and effects of temperature changes.
Slabs Beam Reinforcement Detailing
This document provides problems and examples related to detailing of beams and slabs in reinforced concrete structures. It discusses concepts like continuous beams, cantilever beams, flanged beams, one-way slabs, and two-way slabs. Seven problems are presented involving drawing the longitudinal section and cross sections of beams and slabs and showing reinforcement details. The document concludes with two problems for the reader to solve involving preparing bar bending schedules and estimating quantities of steel and concrete.
Beams
OUTLINE
introduction
classification
loads
materials used
Type of reinforcement
RCC
construction methods in RCC
Analysis and design
Detailing
Basic Rules
Site visit
video
Types of beam & types of supports
This document discusses different types of beams and supports used in engineering mechanics. It describes four types of supports - fixed, simple, roller, and hinged - based on how they restrict the movement of beams. It also outlines six types of beams defined by their support conditions: fixed, cantilever, simply supported, overhanging, continuous, and combinations of these. Finally, it categorizes loads as point, uniformly distributed, or uniformly varying based on how forces are applied along the beam.
Columns
This document discusses different types of columns used in construction. It defines a column as a structural member subjected to compressive axial loads. Columns are classified as long, short, or intermediate based on their length-to-minimum radius of gyration ratio. Long columns have a ratio greater than 50, short columns less than 15-50, and intermediate between 30-100. The document provides examples of column types and discusses effective length, radius of gyration, buckling load, and Euler's formula for calculating crippling load.
Bending stresses
The document discusses bending stresses in beams. It describes how bending stresses are developed in beams to resist bending moments and shearing forces. The theory of pure bending is introduced, where only bending stresses are considered without the effect of shear. Equations for calculating bending stresses are derived based on the beam's moment of inertia, bending moment, and distance from the neutral axis. Several beam cross-section examples are provided to demonstrate how to calculate the maximum bending stress and section modulus.
Design of bolted connections
This document discusses types of bolt connections based on arrangement of bolts and plates, mode of load transmission, and nature and location of load. There are two main types of joints subjected to axial loads: lap joints and butt joints. Butt joints are preferable to lap joints because the load is split between members, eliminating eccentricity and bending. Bolt connections can fail due to shear, bearing, or tension failures of bolts or plates. The design strength of bolts is governed by their strength in shear, bearing, or tension with safety factors applied.
Design of R.C.C Beam
information on types of beams, different methods to calculate beam stress, design for shear, analysis for SRB flexure, design for flexure, Design procedure for doubly reinforced beam,
Beam ,Loads,Supports , trusses
The document discusses different types of structural elements used in building construction including beams, loads, supports, columns, and trusses. It describes several types of beams such as simply supported beams, continuous beams, overhanging beams, cantilever beams, and fixed beams. It also discusses different types of loads, supports, and how columns and trusses function structurally.
Beam Deflection Formulae
1. The document provides formulas for calculating slope, deflection, and maximum deflection for various beam types under different loading conditions. It gives the equations for cantilever beams with concentrated loads, uniformly distributed loads, and varying loads. It also provides the equations for simply supported beams with these different load types and with couple moments applied. The equations relate the beam properties like length, load location, and intensity to the resulting slope and deflection values.
Types of loads, beams, support and support reaction calculation
give information on:-
types of loads
types of beams
types of support
support reaction calculation
Reinforced column design
The document discusses reinforced concrete columns, including their functions, failure modes, classifications, and design considerations. Columns primarily resist axial compression but may also experience bending moments. They can fail due to compression, buckling, or a combination. Design depends on whether the column is short or slender, braced or unbraced. Reinforcement is designed based on the column's expected loads and dimensions using methods specified in design codes like BS 8110.
Shear stresses on beam (MECHANICS OF SOLIDS)
This document provides information about shear stresses and shear force in structures. It includes:
- Definitions of shear force and shear stress. Shear force is an unbalanced force parallel to a cross-section, and shear stress develops to resist the shear force.
- Explanations of horizontal and vertical shear stresses that develop in beams due to bending moments. Shear stress is highest at the neutral axis and reduces towards the top and bottom of the beam cross-section.
- Derivations of formulas for calculating shear stress across different beam cross-sections. Shear stress is directly proportional to the shear force and beam geometry.
- Examples of calculating maximum and average shear stresses for various cross-sections
Types of Beam Support | Mechanical Engineering
Beam is a structural member whose lateral dimensions are much smaller than the longitudinal dimension and used to carry loads perpendicular to the longitudinal axis. Copy the link given below and paste it in new browser window to get more information on Types of Beam Support:- http://www.transtutors.com/homework-help/mechanical-engineering/bending-moment-and-shear-force/types-of-beam-support.aspx
Design of combined footing ppt
The document discusses the design of a combined footing to support two columns. It first defines what a combined footing is and why it is used. It then describes the types of combined footings and the forces acting on it. The document provides the design steps for a rectangular combined footing, which include determining dimensions, reinforcement requirements, and design checks. As an example, it shows the detailed design of a rectangular combined footing supporting two columns with loads of 450kN and 650kN respectively. The design includes calculating dimensions, reinforcement, development lengths, and design checks.
What's hot (20)
Types of loads, beams, support and support reaction calculation
Types of loads, beams, support and support reaction calculation
More from Transweb Global Inc
Resultant of Coplanar Parallel Forces | Mechanical Engineering
If two or more than two forces are acting on a single plane then the forces are known as System of Coplanar Forces and if they are acting on different planes then the forces are called as Non-Coplanar Forces. Copy the link given below and paste it in new browser window to get more information on Resultant of Coplanar Parallel Forces:-
http://www.transtutors.com/homework-help/mechanical-engineering/force-systems-and-analysis/resultant-of-coplanar-parallel-forces.aspx
The Centroidal Axis | Mechanical Engineering
The force of attraction exerted by the earth on a solid body is known as Gravitational Force. It acts in a vertically downward direction and is known as weight of the body. Thus, the weight of the body is assumed to act at a point which is known as Centre of Gravity of a body. Copy the link given below and paste it in new browser window to get more information on The Centroidal Axis:-
http://www.transtutors.com/homework-help/mechanical-engineering/bending-stress/moment-of-inertia-about-the-centroidal-axis1.aspx
System Of Coplanar Forces | Mechanical Engineering
A force is a physical quantity that tends to change the behavior of a solid body when applied upon. This change in behavior may be change in shape of the body or motion of the body in the direction of its action. The force is a vector quantity since it has magnitude and direction. Copy the link given below and paste it in new browser window to get more information on System Of Coplanar Forces:-
http://www.transtutors.com/homework-help/mechanical-engineering/force-systems-and-analysis/system-of-coplanar-forces.aspx
Resultant of Two Unlike and Unequal Parallel Forces | Mechanical Engineering
A force is an external agent which changes or tends to change the behavior of any solid body. It is a vector quantity since it is designated with magnitude and direction. The forces may be of tensile or compressive in nature. Copy the link given below and paste it in new browser window to get more information on Resultant of Two Unlike and Unequal Parallel Forces:-
http://www.transtutors.com/homework-help/mechanical-engineering/force-systems-and-analysis/resultant-of-two-unlike-and-unequal-parallel-forces.aspx
SFD Load Diagram Examples | Mechanical Engineering
Beam is a structural member whose lateral dimensions are much smaller than the longitudinal dimension and used to carry loads perpendicular to the longitudinal axis. The beams are generally used in buildings, bridges, trusses, etc., Copy the link given below and paste it in new browser window to get more information on SFD Load Diagram Examples:-
http://www.transtutors.com/homework-help/mechanical-engineering/bending-moment-and-shear-force/sfd-load-diagram-examples.aspx
Principle Of Transmissibility | Mechanical Engineering
A force is an external agent acting on another body. This force may moves or tends to move the body in the direction of its action. The force is a vector quantity since it is represented by its magnitude and direction. The force may be of pulling or pushing type. Copy the link given below and paste it in new browser window to get more information on Principle Of Transmissibility:-
http://www.transtutors.com/homework-help/mechanical-engineering/force-systems-and-analysis/principle-of-transmissibility.aspx
Law Of Polygon | Mechanical Engineering
If a body is subjected to many forces on its plane at a single point then they are called as Coplanar Concurrent Forces. The effect of the forces acting on the body is unknown. It is necessary to determine the resultant force of the coplanar forces to know this effect. Copy the link given below and paste it in new browser window to get more information on Law Of Polygon:-
http://www.transtutors.com/homework-help/mechanical-engineering/force-systems-and-analysis/law-of-polygon.aspx
Similarities between Leadership and Management | Management
In many aspects, leadership and management are almost known as Synonymous but both the words mean different. Similarities between Leadership and ManagementLeadership is an important and essential part of management. Without leadership, the meaning of management won’t be completed. Copy the link given below and paste it in new browser window to get more information on Similarities between Leadership and Management:-
http://www.transtutors.com/homework-help/industrial-management/leadership/similarities-between-leadership-and-management.aspx
Ranked Positional Weight Method | Management
The Ranked Positional Weight Method is a technique used for assembly line balancing that takes into account precedence relationships and task processing times. It involves calculating a Ranked Positional Weight for each work element based on duration and precedence, arranging them in descending order, and then assigning them to workstations to optimize time, machinery, labor and output. The example shows the steps of constructing a precedence diagram, calculating RPW values, ordering by RPW, and assigning elements to six workstations with the goal of minimizing idle time.
Business Intelligence And Business Analytics | Management
Business Intelligence is the initial basic step of Business Analytics. It refers to gathering raw and complex data, and converting it into systematic and logical information in a format that is usable by the end user. Copy the link given below and paste it in new browser window to get more information on Business Intelligence And Business Analytics:-
http://www.transtutors.com/homework-help/management/managing-information-technology/business-intelligence-analytics/
ABC Cost Hierarchy | Management
The document discusses the levels of an activity-based costing (ABC) system. It explains that under ABC, costs are first assigned to activities and then traced to products. There are four levels of costs: unit, batch, product, and facility. Unit costs are directly proportional to the number of units produced. Batch costs are proportional to the number of batches produced regardless of batch size. Product costs can be traced to a product line. Facility costs are incurred for the plant as a whole and cannot be traced to specific units or products. The document provides examples for each cost level.
Speed To Market | Management
In today’s competitive world the term Speed to Market plays an important role for everyone. So, Speed to Market means the pace of introducing any change, innovation, creativity, any market practice for the purpose of increasing the Promotion of the product as quickly as possible in the market. Copy the link given below and paste it in new browser window to get more information on Speed To Market:-
http://www.transtutors.com/homework-help/industrial-management/product-development/speed-to-market.aspx
Managerial Hubris | Finance
The document discusses the concept of managerial hubris, which refers to excessive pride or self-confidence held by senior managers that can lead to cognitive biases and poor decision making. Managerial hubris can result in empire building within an organization as managers seek to expand their power and influence. It is also related to mergers and acquisitions if acquiring company managers overestimate their ability to manage target companies. This can lead to winners' curse, where the winning bid exceeds the true value of the target. The hubris hypothesis suggests managerial hubris in acquisitions can result in bids over the intrinsic value and ultimately lower shareholder returns.
Conductance | Electrical Engineering
Conductance is an ability of a material to allow the passage of current or fluid or temperature through different materials. It is opposite of resistance through a path, higher the conductivity of material lower is its resistance. It is most commonly used with electrical circuits, though it is also used in fluid and thermals. Copy the link given below and paste it in new browser window to get more information on Conductance:-
http://www.transtutors.com/homework-help/electrical-engineering/conductance.aspx
Advantages and Disadvantages of Digital Electronics | Electrical Engineering
Digital Electronics circuits are those which operate with digital signals. These are discrete signals which are sampled from analog signal. Digital circuits use binary notation for transmission of signal. Copy the link given below and paste it in new browser window to get more information on Advantages and Disadvantages of Digital Electronics:-
http://www.transtutors.com/homework-help/electrical-engineering/digital-electronics/advantages-disadvantages/
Stabilization Of Operating Point | Electrical Engineering
This document discusses the stabilization of operating point in BJTs. It defines the load line and operating point, and explains that the operating point depends on factors like current gain, temperature, and supply voltage variations. An increase in current gain or temperature will shift the operating point towards saturation. It also describes different bias circuit types - fixed bias, collector base bias, fixed bias with emitter resistance, and voltage divider bias - and provides their basic equations.
Offer Curves | Economics
Curves are of different types and for different purposes. Some of the curves are utility curve, margin curves, demand and supply curve, offer curves, etc. International trade is based on international specialization. Copy the link given below and paste it in new browser window to get more information on Offer Curves:-
http://www.transtutors.com/homework-help/international-economics/analytical-tools/offer-curves.aspx
Fixed Exchange Rate | Economics
Currency is any form of money in general circulation in a country. Foreign exchange is money denominated in the currency of another country or a group of countries. Simply, an exchange rate is defined as the rate at which the market converts one currency into another. Copy the link given below and paste it in new browser window to get more information on Fixed Exchange Rate:-
http://www.transtutors.com/homework-help/international-economics/economic-policy-in-open-economy/fixed-exchange-rate/
Computer Architecture | Computer Science
Computer Architecture is the set of pre-defined rules and methods that describes the functionality of computer system. In other words, a computer consists of both hardware and software and using some rules and methods for the interaction of both hardware and software of a computer is known as computer architecture. Copy the link given below and paste it in new browser window to get more information on Computer Architecture:-
http://www.transtutors.com/homework-help/computer-science/computer-architecture/
Compilers Computer Program | Computer Science
One of the great advantages of high-level programming languages such as c, c++, and java is that they are machine independent. Programs written in the high-level languages can run on any machine. This is possible because of the compiler. Copy the link given below and paste it in new browser window to get more information on Compilers computer program:-
http://www.transtutors.com/homework-help/computer-science/compilers-computer-program.aspx
More from Transweb Global Inc (20)
Resultant of Coplanar Parallel Forces | Mechanical Engineering
Resultant of Coplanar Parallel Forces | Mechanical Engineering
System Of Coplanar Forces | Mechanical Engineering
System Of Coplanar Forces | Mechanical Engineering
Resultant of Two Unlike and Unequal Parallel Forces | Mechanical Engineering
Resultant of Two Unlike and Unequal Parallel Forces | Mechanical Engineering
SFD Load Diagram Examples | Mechanical Engineering
SFD Load Diagram Examples | Mechanical Engineering
Principle Of Transmissibility | Mechanical Engineering
Principle Of Transmissibility | Mechanical Engineering
Similarities between Leadership and Management | Management
Similarities between Leadership and Management | Management
Business Intelligence And Business Analytics | Management
Business Intelligence And Business Analytics | Management
Advantages and Disadvantages of Digital Electronics | Electrical Engineering
Advantages and Disadvantages of Digital Electronics | Electrical Engineering
Stabilization Of Operating Point | Electrical Engineering
Stabilization Of Operating Point | Electrical Engineering
Recently uploaded
Your Skill Boost Masterclass: Strategies for Effective Upskilling
Your Skill Boost Masterclass: Strategies for Effective UpskillingExcellence Foundation for South Sudan
Strategies for Effective Upskilling is a presentation by Chinwendu Peace in a Your Skill Boost Masterclass organisation by the Excellence Foundation for South Sudan on 08th and 09th June 2024 from 1 PM to 3 PM on each day.DRUGS AND ITS classification slide share
Any substance (other than food) that is used to prevent, diagnose, treat, or relieve symptoms of a
disease or abnormal condition
Azure Interview Questions and Answers PDF By ScholarHat
Azure Interview Questions and Answers PDF By ScholarHat
The History of Stoke Newington Street Names
Presented at the Stoke Newington Literary Festival on 9th June 2024
www.StokeNewingtonHistory.com
ANATOMY AND BIOMECHANICS OF HIP JOINT.pdf
it describes the bony anatomy including the femoral head , acetabulum, labrum . also discusses the capsule , ligaments . muscle that act on the hip joint and the range of motion are outlined. factors affecting hip joint stability and weight transmission through the joint are summarized.
What is Digital Literacy? A guest blog from Andy McLaughlin, University of Ab...
What is Digital Literacy? A guest blog from Andy McLaughlin, University of Aberdeen
How to Setup Warehouse & Location in Odoo 17 Inventory
In this slide, we'll explore how to set up warehouses and locations in Odoo 17 Inventory. This will help us manage our stock effectively, track inventory levels, and streamline warehouse operations.
PCOS corelations and management through Ayurveda.
This presentation includes basic of PCOS their pathology and treatment and also Ayurveda correlation of PCOS and Ayurvedic line of treatment mentioned in classics.
Main Java[All of the Base Concepts}.docx
This is part 1 of my Java Learning Journey. This Contains Custom methods, classes, constructors, packages, multithreading , try- catch block, finally block and more.
Advanced Java[Extra Concepts, Not Difficult].docx
This is part 2 of my Java Learning Journey. This contains Hashing, ArrayList, LinkedList, Date and Time Classes, Calendar Class and more.
Recently uploaded (20)
Your Skill Boost Masterclass: Strategies for Effective Upskilling
Your Skill Boost Masterclass: Strategies for Effective Upskilling
Azure Interview Questions and Answers PDF By ScholarHat
Azure Interview Questions and Answers PDF By ScholarHat
Pride Month Slides 2024 David Douglas School District
Pride Month Slides 2024 David Douglas School District
Digital Artefact 1 - Tiny Home Environmental Design
Digital Artefact 1 - Tiny Home Environmental Design
What is Digital Literacy? A guest blog from Andy McLaughlin, University of Ab...
What is Digital Literacy? A guest blog from Andy McLaughlin, University of Ab...
How to Setup Warehouse & Location in Odoo 17 Inventory
How to Setup Warehouse & Location in Odoo 17 Inventory
Simply Supported Beam Examples | Mechanical Engineering
- 2. Introduction Simply Supported Beam Examples
- 3. Beam • Structural member used to carry transverse loads Simply Supported Beam • Both ends of a beam are supported by end supports to carry transverse loads
- 4. Find the reactions at the ends of a simply supported beam loaded as shown in figure.
- 5. Find the reactions at the ends of a simply supported beam loaded as shown in figure.
- 6. This was just a summary on Simply Supported Beam Examples. For more detailed information on this topic, please type the link given below or copy it from the description of this PPT and open it in a new browser window. www.transtutors.com/homework-help/mechanical-engineering/bending- moment-and-shear-force/simply-supported-beam-examples.aspx