1. Varies
TOILET CLEARANCE REQUIREMENTS (NTS)
40"min(1016)
29"min(730)
27"min(690)
8"min(220)
30"min(700)
CLEAR
FLOOR
SPACE
17" min (430)
19" min (485)
48" min (1220)
toe clearance
8" max (150)
knee clearance
8" min (203)
lav depth
17" min (430)
42 MIN
1065
56MIN
1420
TOILET CLEARANCE REQUIREMENTS (NTS)
18
455
FUTURE TOILET ADAPTABILITY REQUIREMENTS (NTS)
SUSPENDED CEILING DETAIL (NTS)
36 min
24 min 12 min
33-36
33-36
39-4118min
42 min
12 max
54 min
39-41
REAR WALL GRAB BAR
FOR WATER CLOSET
SIDE WALL GRAB BAR FOR
WATER CLOSET
17-19
HEIGHT OF WATER CLOSETBEFORE REMOVAL OF CABINETS AFTER REMOVAL OF CABINETS
30 MIN
48MAX
28-36
1929
48
30
CLEAR FLOOR SPACE UNDER
WORK SURFACE
Varies
36"MIN
915
36" MIN
915
48" MIN
1220
30"MIN
700
SHOWER CLEARANCE REQUIREMENTS (NTS)
NEW DOOR DIMENSIONS (NTS)
LATCH APPROACH
PULL SIDE
KITCHEN CLEARANCE (NTS)
40MIN
1525
TUB CLEARANCE REQUIREMENTS (NTS)
SEAT
LAV
60 MIN
1525
48MIN
CLEAR
FLOOR
SPACE
CLEAR
FLOOR
SPACE
TOILET CLEARANCE REQUIREMENTS (NTS)
SLIDING DOOR APPROACH
42MIN
22 MIN
1065
560
* 54" MIN (1370) IF CLOSER IS
PROVIDED
48MIN*
24 MIN
1220
610
36 MIN
915
>24
610
DOORWAYS WITHOUT DOORS
WORK ITEMS including new
and/or replacement
ENVELOPE, WINDOWS,
DOORS
PROPOSED DESIGNED
VALUES
CODE PRESCRIBED VALUE
AND CITATION
INTERIOR PARTITIONS
BETWEEN CONDITIONED
CORRIDOR AND
CONDITIONED APARTMENT
PIPING INSULATIONS
HVAC SYSTEM
TO THE BEST OF MY KNOWLEDGE, BELIEF AND PROFESSIONAL JUDGEMENT, THESE
PLANS AND SPECIFICATIONS ARE IN COMPLIANCE WITH THE ENERGY CONSERVATION
CONSTUCTION CODE OF NEW YORK STATE AND NYC LOCAL LAW 1/2011.
NO CHANGE
NO CHANGE
NO CHANGE
NO CHANGE
ENERGY ANALYSIS
RESIDENTIAL ----> FOLLOWING UNDER COMMERCIAL REQUIREMENT
APARTMENT ALTERATION TO UNIT 10A, 10th FLOOR IN A 31 STORY BUILDING
CLIMATE ZONE 4 ---> 11B
INTERIOR LIGHTING NO CHANGE
N/A
N/A
N/A
N/A
N/A
APT# 12B, 12th FLOOR
THE ROTHMAN RESIDENCE
NEW YORK, NEW YORK 10025
670 WEST END AVE
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
2. NO CHANGE TO USE, EGRESS OR OCCUPANCY UNDER THIS APPLICATION.
PIPING AND INSULATION NOT TO BE DISTURBED DURING ALTERATION.
THE ARCHITECT AND GENERAL CONTRACTOR HAVE READ, ARE FAMILIAR
WITH AND WILL ABIDE BY THE BUILDING HOUSE RULES, MANDATORY
DESIGN GUIDELINES AND GENERAL INFORMATION FOR SHAREHOLDERS.
PLUMBING AND GAS RISERS WILL NOT BE RELOCATED OR REROUTED.
ADDRESS: 670 WEST END AVE, NEW YORK, NY, 10075
APT. NO.: 12B
BLOCK NO.: 240 LOT NO.: 61
MAP NO: 5D ZONING: R10-A
GENERAL NOTES:
1. DRAWING NOT TO BE SCALED.
2. CONTRACTOR MUST VERIFY ALL MEASUREMENTS AND CONDITIONS
PRIOR TO THE COMMENCEMENT OF WORK, AND REPORT ANY
DISREPENCIES IMMEDIATELY, IN WRITING, TO THE ARCHITECT AND
OWNER.
3. DOOR BUCKS IN RELOCATED DOORS SHALL BE PROVIDED TO
ALLOW FOR REMOUNTING OF DOOR AN SAME FRAME IN ORDER TO
ACHIEVE ALTERNATE SWING.
4. CARE WILL BE TAKEN NOT DISTURB EXISTING HEAT RISERS,
ELECTRICAL RISERS, GAS RISER, VENTILATION SHAFTS, AND
MISCELLANEOUS RISERS (INTERCOM, ETC) TYPICALLY FOUND IN
THE UNIT. WE WILL NOT RELOCATE OR DISRUPT ANY OF EXISTING
RISERS. WE WILL NOT DISTURB EXISTING EXTERIOR
WATERPROOFING. WE WILL NOT INTERFERE WITH HEATING OR
WINDOW OPERATION IS ALLOWED. WE WILL NOT PENETRATE
EXTERIOR WALLS IS ALLOWED UNLESS SPECIFICALLY APPROVED BY
BOARD.
DEMOLITION NOTES:
1. ALL DEMOLITION WORK SHALL BE PERFORMED IN A SAFE AND
LEGAL MANNER.
2. DEBRIS SHALL BE REMOVED IN A TIMELY AND LEGAL MANNER.
3. PRIOR TO DEMOLITION, THE CONTRACTOR SHALL FULLY PROTECT
AND SAFEGUARD ALL ADJOINING CONSTRUCTION, EQUIPMENT AND
PROPERTY NOT SCHEDULED FOR DEMOLITION, INCLUDING THE
PUBLIC HALLWAY.
4. THE CONTRACTOR SHALL PROVIDE ALL SUPPORTS, BRACING AND
SHORING REQUIRED TO SAFEGUARD EXISTING AND ADJOINING
CONSTRUCTION.
5. DURING DEMOLITION AND AS REQUIRED DURING CONSTRUCTION
OPERATIONS, THE CONTRACTOR SHALL INSPECT AND PERFORM
EXPLORATORY PROBES TO DETERMINE THE EXTENT, LAYOUT AND
CONDITION OFF EXISTING CONSTRUCTION TO BE AFFECTED BY THE
NEW WORK, AS CALLED FOR ON THE DRAWINGS OR A OTHERWISE
REQUIRED. THE CONTRACTOR SHALL NOTIFY THE ARCHITECT OF
ALL CONDITIONS DISCOVERED AT VARIANCE WITH THE DRAWINGS
OR DESIGN INTENT.
6. THE CONTRACTOR SHALL MAKE PROBES AS REQUIRED TO
ASCERTAIN ANY REQUIRED PROTECTIVE MEASURES PRIOR TO
PROCEEDING WITH DEMOLITION/REMOVAL WORK OR THE
INSTALLATION OF NEW WORK JOINING EXISTING.
7. REMOVE PLUMBING FIXTURES AS NOTED.
8. REMOVE ALL EXISTING FLOOR FINISHES IN KITCHENS AND
BATHROOMS DESIGNATED TO RECEIVE NEW FLOOR FINISHES OF
PARQUET OR TILE.
9. THE CONTRACTOR SHALL REMOVE ALL SPECIFIED PORTIONS OF
EXISTING CONSTRUCTION, FINISHES, FIXTURES AND EQUIPMENT AS
SHOWN ON THE DRAWINGS OR OTHERWISE REQUIRED. CUTS AT
NEW WORK LINES SHALL BE SHARP AND NEAT, AND ALL
REMAINING CONSTRUCTION AND FINISHES SHALL BE FULLY BACKED
AND REINFORCED PRIOR TO THE INSTALLATION OF THE NEW WORK.
THE CONTRACTOR SHALL PROVIDE AND MAINTAIN TEMPORARY
PROTECTION OF NEW WORK WHICH IS LIABLE TO DAMAGE DURING
THE COURSE OF THE JOB.
TENANT SAFETY NOTES:
1. CONSTRUCTION WORK WILL BE CONFINED TO THE APARTMENT
INTERIOR, AND WILL NOT CREATE DUST, DIRT OR OTHER
INCONVENIENCES TO OTHER APARTMENT UNITS WITHIN THE
BUILDING.
2. CONSTRUCTION OPERATIONS WILL NOT BLOCK HALLWAYS OR
MEANS OF EGRESS FOR THE TENANTS OF THE BUILDING.
3. CONSTRUCTION OPERATIONS WILL NOT INVOLVE
INTERRUPTIONS OF THE HEATING, WATER OR ELECTRICAL
SERVICES TO OTHER TENANTS OF THE BUILDINGS.
4. CONSTRUCTION OPERATIONS WILL BE CONFINED TO NORMAL
WORKING HOURS MONDAY THROUGH FRIDAY, AS PER THE
ALTERATION PROCEDURES DOCUMENTS. NO WORK WILL BE
DONE ON EITHER LEGAL HOLIDAYS OR WEEKENDS WITHOUT A
VARIANCE ISSUED BY THE NYC DEPARTMENT OF BUILDINGS.
TENANT PROTECTION PLAN 28-104.8.4 2008 CODE:
1. THE BUILDING CONTAINS APPROXIMATELY 93 DWELLING UNITS
THAT WILL BE OCCUPIED DURING CONSTRUCTION.
2. EGRESS: AT ALL TIMES IN THE COURSE OF CONSTRUCTION THE
EGRESS FROM THE VARIOUS FLOORS OF THE BUILDING WILL BE
MAINTAINED.
3. FIRE SAFETY: ALL PRECAUTIONS TO BE OBSERVED TO MAINTAIN
FIRE SAFETY AS WELL AS ADDITIONAL SAFETY MEASURES
NECESSITATED BY THE CONSTRUCTION SHALL BE STRICTLY
OBSERVED.
4. HEALTH REQUIREMENTS: DUST TO BE KEPT TO A MINIMUM AND TO
BE REMOVED AFTER COMPLETION OF WORK EACH DAY. DISPOSAL
OF CONSTRUCTION DEBRIS MUST BE DONE IN A SAFE MANNER.
CONSTRUCTION NOISE WILL BE CEASED AFTER NORMAL WORKING
HOURS, LIMIT NOISE TO ACCEPTABLE LEVELS. MAINTAIN SANITARY
FACILITIES. CONTROL PESTS AT ALL TIMES.
5. CONTRACTOR MUST COMPLY WITH APPLICABLE LAWS RELATION TO
LEAD AND ASBESTOS. IF OBSERVED IMMEDIATELY CONTACT
OWNER OR ARCHITECT.
6. ELECTRIC, GAS OR OTHER UTILITIES ARE NOT TO BE INTERRUPTED.
7. BUILDING SECURITY TO BE MAINTAINED TO PREVENT
UNAUTHORIZED PERSONS FROM ENTERING THE BUILDING.
CONTROLLED INSPECTION NOTES:
CONTROLLED INSPECTIONS AS REQUIRED BY THE BUILDING CODE SHALL
BE MADE AS FOLLOWS:
1. FINAL
2. FIRE STOPPING
TECHNICAL RESPONSIBILITY REPORT FORMS SHALL BE FILED.
BUILDING DEPARTMENT NOTES:
1. PRIOR TO ANY CONSTRUCTION WORK, THE CONTRACTOR SHALL
OBTAIN ALL REQUIRED WORK PERMITS.
2. ALL WORK SHALL CONFORM TO APPROVED PLANS, ALL APPLICABLE
CODES AND BUILDING DEPARTMENT RULES AND REGULATIONS. ALL
CONSTRUCTION SHALL BE IN COMPLIANCE WITH THESE
REQUIREMENTS.
3. THE CONTRACTOR SHALL PROTECT AND MAKE SAFE ADJACENT
PROPERTY AND ADJACENT SPACES WITHIN THE PREMISES AS
REQUIRED BY JOB CONDITIONS. THE CONTRACTOR SHALL MAINTAIN
THESE CONDITIONS THROUGHOUT THE COURSE OF THE JOB.
4. ASBESTOS OR MATERIALS, PROCESSES OR PROCEDURES WHICH
CONTAIN OR EMPLOY ASBESTOS ARE PROHIBITED.
5. ALL CONSTRUCTION SHALL CONFORM TO OR EXCEED ACCEPTED
STANDARDS OF SUPERIOR WORKMANSHIP.
6. THE CONTRACTOR SHALL PROVIDE PROPER CERTIFICATES OF
INSURANCE AND WORKERS' COMPENSATION TO THE OWNER PRIOR
TO BEGINNING WORK.
SMOKE/CARBON MONOXIDE DETECTOR NOTES:
1. SMOKE/CARBON MONOXIDE DETECTORS OR DEVICES SHALL BE
INSTALLED IN ACCORDANCE WITH THE HOUSING MAINTENANCE
CODE, MULTIPLE DWELLING LAW OF THE NEW YORK CITY BUILDING
CODE AND THE NEW YORK CITY ELECTRICAL CODE AND TO COMPLY
WITH LL7/04.
2. SMOKE DETECTORS AND CARBON MONOXIDE DETECTORS MAY BE
COMBINED PROVIDING THE DEVICES COMPLY WITH THE PROVISIONS
OF TITLE OF THE ADMINISTRATIVE CODE OF NEW YORK AND ANY
APPLICABLE RULES PROMULGATED HEREUNDER.
3. EACH SMOKE/CARBON MONOXIDE DETECTOR SHALL BE INSTALLED
IN ACCORDANCE WITH REFERENCE STANDARD 17-12 OF THE NEW
YORK CITY BUILDING CODE.
4. EACH SMOKE/CARBON MONOXIDE DETECTOR SHALL BE INSTALLED
OUTSIDE OF EACH SLEEPING ROOM IN THE IMMEDIATE VICINITY OR
WITHIN 10'-0" OF THE ENTRANCE TO A SLEEPING ROOM.
5. EACH SMOKE/CARBON MONOXIDE DETECTOR SHALL BE OF A TYPE
THAT ALLOWS FOR READILY TESTING OF SUCH DEVICE.
6. DUPLEX UNITS SHALL HAVE A DEVICE LOCATED ON EACH LEVEL IF
ONLY ONE MEANS OF EGRESS IS PROVIDED FROM EACH LEVEL,.
7. CEILING MOUNTED DEVICES SHALL BE A MINIMUM DISTANCE OF 4"
FROM ANY WALL.
8. WALL MOUNTED DEVICES SHALL BE A MINIMUM OF 4" TO A
MAXIMUM OF 12" FROM THE CEILING.
9. EACH DWELLING UNIT SHALL BE EQUIPPED WITH AN APPROVED
TYPE SMOKE/CARBON MONOXIDE DETECTOR DEVICE RECEIVING
PRIMARY POWER FROM THE BUILDING WIRING WITH NO SWITCHES
ON THE CIRCUIT OTHER THAN T HE OVER CURRENT DEVICE
PROTECTING THE BRANCH CIRCUIT AS PER NEW YORK CITY
BUILDING CODE SECTION 27-980.
10. SUCH SMOKE/CARBON MONOXIDE DETECTOR MUST BE EITHER THE
IONIZATION CHAMBER TYPE OIR THE PHOTOELECTRIC DETECTOR
TYPE AS PER NEW YORK CITY BUILDING CODE SECTION 27-981, (B).
11. A "CERTIFICATE OF SATISFACTORY INSTALLATION FOR
SMOKE/CARBON MONOXIDE DETECTORS" MUST BE FILED WITH THE
DIVISION OF CODE ENFORCEMENT H.P.D., 10 DAYS AFTER
INSTALLATION.
12. WRITTEN INFORMATION OF TESTING AND MAINTENANCE OF THE
DEVICES SHALL BE PROVIDED TO THE DWELLING UNIT OWNER.
SIDE 1
ALLOWABLE DEFLECTION L/240
SIDE 1
SILL
MARK
H2
H1
UL DESIGN
NUMBER
U420
U420
FIRE
RATING
STUD SIZE
OVERALL
DIMENSION
SEE
PLANS
SEE
PLANS 2 HR
2 HR
3 5/8"
2 1/2"
INSUL.
THICK.
SOUND
ATTEN.
STC
RATING
-
-
1 1/2"
3 1/2"YES
YES
SIDE 2
HEAD
PLAN
2 LAYERS 5/8" TYPE X GYP. BD EACH SIDE @
TWO HOUR RATED CONDITION
FASTENERS @ 2'-0"
O.C. MAX. AND
WITHIN 3" OF ENDS
DESIGN LOAD 5 PSF
20 GA.25 GA. 22 GA.
-
--
-22'-9"
17'-6"
LIMITING HEIGHT
TOP OF SLAB
SCHEDULED WALL FINISH
CONTINUOUS ACOUSTICAL SEALANT - BOTH SIDES
(FIRESTOP SEALANT @ RATED PARTITIONS)
CONT. 20 GA. CHANNEL SHAPED MTL. RUNNER
SCHEDULED BASE
BOTH SIDES
NOTE: TYPE "F" FURRING IS AN INTERIOR FINISH GWB. ASSEMBLY
OVERALL
DIMENSION
6 5/8"
4 5/8"
4 1/4"
3 1/8"
2 1/8"
1 1/2"
6"
4"
MARK STUD SIZE
7/8"
1 1/2"
2 1/2"
3 5/8"
F6
F5
F4
F3
F2
F1
FIRE
RATING
UL DESIGN
NUMBER
SOUND
ATTEN.
---
- - -
-
-
-
-
-
--
-
-
-
-
-
SIDE 2
SILL
CONT. ACOUSTICAL SEALANT BOTH SIDES
(FIRESTOP SEALANT @ RATED PATITIONS)
ONE LAYER 5/8" TYPE X GYP. BD. EACH SIDE
(WATER RESISTANT @ WET AREAS)
OVERALL PARTITION DIMENSION
MTL. STUD @ MAX. 16" O.C.
20 GA. x 3 5/8" STUD BRIDGING @ EA. WALL
STUD SPACED @ 4'-0" O.C. VERTICALLY
SOUND ATTENUATION BLANKET AS SCHED.
TAPE & FLOAT JOINT & NAIL HEADS LEVEL
ABOVE FINISH CEILING
BOTTOM OF SLAB
DEEP LEG TRACK WITH
VERTICALLY SLOTTED HOLES
UNDERSIDE OF
STRUCTURE ABOVE
PLAN
HEAD
1 HOUR RATED PARTITION WALLS WITH NONPROTECTED OPENINGS
2 HOUR RATED PARTITION WALLS WITH PROTECTED OPENINGS
SIDE 1
2 HR.8 1/2"6"C4
MARK STUD SIZE
OVERALL
DIMENSION
FIRE
RATING
2 HR.5"2 1/2"C1
2 HR.6 1/8"3 5/8"
2 HR.6 1/2"4"
C2
C3
SILL
PLAN
HEAD
SIDE 2
ACOUSTICAL SEALANT BOTH SIDES
(FIRESTOP SEALANT @ RATED PARTITIONS)
52
ALLOWABLE DEFLECTION L/240
STC
RATING
52
52
YES --
YES 3 1/2"U411
UL DESIGN
NUMBER
SOUND
ATTEN.
INSUL.
THICK.
YES 1 1/2"U411
YES 3 1/2"
-
U411
---
26'-0" 28'-6"20'-0"
DESIGN LOAD 5 PSF
25 GA. 22 GA.
LIMITING HEIGHT
20 GA.
14'-0" 16'-1"
18'-0" 20'-2"
13'-6"
16'-9"
TOP OF SLAB
SCHEDULED BASE
SCHEDULED FLOORING
SOUND ATTENUATION BLANKET
AS SCHEDULED
FASTENERS @ 2'-0" O.C. MAX.
AND WITHIN 3" OF ENDS
CONTINUOUS 20 GA. CHANNEL
SHAPED METAL RUNNER
TWO LAYERS 5/8" TYPE X GYP. BD. EACH SIDE
(FACE LAYER WATER RESISTANT @ WET AREAS)
REFER TO PLANS FOR SPECIFIC
ACOUSTICAL TREATMENT
INTERIOR FINISH @ PERIMETER CORE WALLS
ACOUSTICAL SEALANT BOTH SIDES
(FIRESTOP SEALANT @ RATED PARTITIONS)
SCHEDULED WALL FINISH
OVERALL PARTITION DIMENSION
METAL STUD @ MAX. 16" O.C.
BOTTOM OF SLAB
UNDERSIDE OF STRUCTURE
TOP OF STUD (HOLD DOWN 1/2")
DEEP LEG TRACK WITH
VERTICALLY SLOTTED HOLES
EXTEND GYP. BD. TO UNDERSIDE
OF STRUCTURE ABOVE U.O.N. - DO
NOT FASTEN TO TRACK
OVERALL
DIMENSION
ONE LAYER 5/8" TYPE X GYP. BD.
(WATER RESISTANT @ WET AREAS)
ALLOWABLE DEFLECTION L/240
DESIGN LOAD 5 PSF
22 GA.
-
-
-
-
-
-
LIMITING HEIGHTINSUL.
THICK.
STC
RATING 25 GA.
---
-- -
-
-
-
-
-
-
-
-
-
-
-
-
20 GA.
-
-
-
-
-
-
CONTINUOUS HAT CHANNEL
@ BASE OF FURRING @ F1
CONTINUOUS FURRING CHANNEL @ F2
TOP OF SLAB
SCHEDULED FLOORING
SCHEDULED BASE
ACOUSTICAL SEALANT
OVERALL PARTITION DIMENSION
2 1/2" METAL STUD @ 16" O.C.
7/8" x 20 GA. HAT CHANNEL
(VERTICAL) AT 24" O.C. @ F1
1 1/2" x 20 GA. Z FURRING
CHANNEL (VERTICAL) AT 24" O.C. @ F2
FINISH SURFACE
SCHEDULED WALL FINISH
UNDERSIDE OF STRUCTURE
FACE OF SUBSTRATE, RE: PLANS
( 1 HR MIN. RATED ASSEMBLY )
BOTTOM OF SLAB
ACOUSTICAL SEALANT
8"
6"
3 5/8B7
B8
B9
3 5/8"B6
3 5/8"B5
STUD SIZEMARK
4"
B4
B3
3 5/8"
6"
B2
2 1/2"B1
SIDE 1
SILL
PLAN
HEAD
TWO LAYERS 5/8" TYPE X GYP. BD. EACH SIDE @ B5
(FACE LAYER WATER RESISTANT @ WET AREAS)
25'-3"
25'-3"
17'-3"
3RD LAYER OF 5/8" TYPE X GYP. BD. @ B6
(FACE LAYER WATER RESISTANT @ WET AREAS)
17'-3"
17'-3"
ACOUSTICAL SEALANT BOTH SIDES
(FIRESTOP SEALANT @ RATED PARTITIONS)
CONTINUOUS 20 GA. CHANNEL
SHAPED METAL RUNNER
FASTENERS @ 2'-0" O.C. MAX.
AND WITHIN 3" OF ENDS
SOUND ATTENUATION BLANKET
AS SCHEDULED
ALLOWABLE DEFLECTION L/240
DESIGN LOAD 5 PSF
22 GA.
LIMITING HEIGHT
25'-3"
17'-3"
13'-0"
YES
YES
YES
YES
YES
SOUND
ATTEN.
YES
YES
YES
YES
5 1/2" 1 HR. U465
8 1/2" 1 HR. U465
7 7/8" 1 HR. U465
U4651 HR.7 3/8"
U4651 HR.6 1/8"
-
UL DESIGN
NUMBER
FIRE
RATING
1 HR.5 1/4"
U465
U465
1 HR.
1 HR.4 7/8"
7 1/4"
U4191 HR.3 3/4"
20'-0"
16'-0"45
20'-0"
3 1/2"
3 1/2" 45
3 1/2" 45
16'-0"453 1/2"
16'-0"453 1/2"
3 1/2"
3 1/2"
3 1/2"
--
25 GA.
STC
RATING
INSUL.
THICK.
20'-0"45
16'-0"45
12'-6"401 1/2"
TOP OF SLAB
SIDE 2
SCHEDULED BASE
SCHEDULED FLOORING
26'-1"
17'-11"
26'-1"
17'-11"
17'-11"
--
20 GA.
26'-1"
17'-11"
13'-10"
BOTTOM OF SLAB
ONE LAYER 5/8" TYPE X GYP. BD. EACH SIDE
(FACE LAYER WATER RESISTANT @ WET AREAS)
REFER TO PLANS FOR SPECIFIC
ACOUSTICAL TREATMENT
INTERIOR FINISH @ PERIMETER CORE WALLS
SCHEDULED WALL FINISH
TOP OF STUD (HOLD DOWN 1/2")
OVERALL PARTITION DIMENSION
METAL STUD @ MAX. 16" O.C.
UNDERSIDE OF STRUCTURE
ACOUSTICAL SEALANT BOTH SIDES
(FIRESTOP SEALANT @ RATED PARTITIONS)
EXTEND GYP. BD. TO UNDERSIDE
OF STRUCTURE ABOVE U.O.N. -
DO NOT FASTEN TO TRACK
DEEP LEG TRACK WITH VERTICALY
SLOTTED HOLES
PARTITION TYPES
KITCHEN
PLUMBING RISER DIAGRAM (NTS)
MASTER BATH
Vent line to existing 4" building vent lines
4" drain to building wastes
BATH 2 LAUNDRY
Replace
Toilet
3/4" CW
4" waste
2" vent
Replace
Lavatory
3/4" H&CW
1 1/2" waste
1 1/2" vent
Replace
Lavatory
3/4" H&CW
1 1/2" waste
1 1/2" vent
Replace
Toilet
3/4" CW
4" waste
2" vent
Existing
Tub
3/4" H&CW
1 1/2" waste
1 1/2" vent
18" min.
Tub rim
1 Relocate washer
3/4" H&CW
1 1/2" waste, 1 1/2" vent
w/combination fitting , Watts
hammer arresters(no air chambers )
Replace
Dish washer
3/4" HW
1 1/2" waste
1 1/2" vent
Replace
Sink
3/4" H&CW
2" waste
1 1/2" vent
Replace
stall shower
3/4" H&CW
2" waste
1 1/2" vent
3
4" GAS RISER
REPLACED GAS
RANGE
EXISTING
GAS METER
TO REMAIN
GAS RISER NOTES
1. ALL GAS PIPING SHALL MEET THE REQUIREMENTS OF THE NYC
BUILDING CODE.
2. THE EXISTING AND NEW GAS SHUT-OFFS SHALL BE ACCESSIBLE.
3. SCHEDULE B SHALL BE FILE INDICATING A GAS PIPING
EXTENSION.
4. NO GAS PIPING SHALL BE LOCATED IN THE FLOOR.
5. CON EDISON SHALL BE NOTIFIED OF THE WORK.
6. IT IS A SPECIFIC REQUIREMENT THAT THE COMPLETE GAS
PIPING SHALL BE TESTED BY CONTRACTOR, AND INSPECTED AND
SIGNED OFF BY DOB. SELF-CERTIFICATION BY THE PLUMBER SHALL
NOT BE ALLOWED.
7. PRIOR TO COMMENCING ANY WORK, THE LICENSED PLUMBER
SHALL PRESSURE TEST THE GAS SUPPLY BACK TO THE SAME
POINT REQUIRED BY NYC DOB, IF THE LOSS IN PRESSURE
EXCEEDS CODE LIMITS, NO GAS PIPING WORK MAY BE DONE UNTIL
REPAIRS ARE MADE AT SHAREHOLDER'S EXPENSE, SHOULD IT
NOT BE POSSIBLE TO MAKE THE NECESSARY REPAIRS DUE TO
LIMITED ACCESS TO THE GAS RISER OR FOR OTHER REASONS,
THEN NO GAS PIPING CHANGES WILL BE ALLOWED.
8. PRESSURE TEST SHALL BE AT 3 PSIG AFTER A NEW VALVE AND
TEE IMMEDIATELY ADJACENT TO THE GAS SHUT-OFF. SHUT-OFF
VALVE SHALL BE TESTED WITH SOAP FILM.
WASHER/DRYER NOTES
1. THE CLOTHES WASHER SHALL BE FITTED IN A STEEL PAN, WITH 3
INCH CURB ALL AROUND AND SOUNDPROOFING BELOW. THE PAN
SHALL EXTEND UNDER THE WATER SUPPLY HOSES AS WELL.
STEEL PAN SHALL HAVE DUAL LEVEL TYPE DRAIN CONNECTED TO
WASTE RISER.
2. THE PAN SHALL HAVE A WATTS 'INTELLIFLOW' SENSOR THAT
AUTOMATICALLY SHUTS OFF THE HOT AND COLD WATER
SUPPLIES AND HAS AN AUDIBLE ALARM.
3. PROVIDE SHUT-OFF VALVES,AIR CHAMBERS ARE NOT TO BE USED.
ONLY HAMMER ARRESTERS WILL BE INSTALLED AND NYC
APPROVED BACKFLOW PREVENTION DEVICES ON HOT AND COLD
WATER SUPPLY PIPING.
4. WASHING MACHINE FLEXIBLE WATER SUPPLY HOSES SHALL BE
"NO BURST" BRAIDED STAINLESS STEEL/NEOPRENE TYPE, NOT
BLACK RUBBER HOSES.
5. WASHING MACHINE DRAINS ARE TO FLOW INTO AN OPEN HUB
2-1/2" STANDPIPE, WITH HUB ELEVATION 6 INCHES ABOVE THE
FLOOD LEVEL OF THE MACHINE.
SHUT-OFF VALVE
GAS RISER DIAGRAM (NTS)
12th FLOOR
CELLAR
PLUMBING NOTES
1. ALL ROUGH-IN PLUMBING WORK SHALL
BE PERFORMED BY A LICENSED PLUMBER.
2. ALL BRANCH LINES ARE REQUIRED TO BE
REPLACED WITH NEW PIPING BACK TO
THE BUILDING RISERS INCLUDING
SHOWER/TUB TRAINS AND WATER
CLOSET WASTE CONNECTIONS.
3. ALL LAVATORIES WILL BE PROVIDED WITH
AN OVERFLOW, OR IF NO OVERFLOW IS
PROVIDED THEN A 2" TRAP AND
UNOBSCURED DRAIN WILL BE PROVIDED
INSTEAD.
4. WATERPROOFING TO EXTEND IN
PARTITION WALLS UNDER IN-WALL
TOILET TANKS.
5. BUILDING SUPER TO WITNESS SHOWER
PAN 24 HOUR TEST AND TO APPROVE
ACCESS DOOR LOCATIONS
6. NEW PIPES TO BE INSULATED WITH
BUILDING APPROVED SPECIFICATION
Remove
Toilet
Remove
Lavatory
Replace
Icemaker in
Freezer
1/2" CW
POWDER
4" drain to building wastes
Vent line to existing 4" building vent lines
Relocate
Sink
3/4" H&CW
2" waste
1 1/2" vent
BAR
SHUT-OFF VALVE
REPLACED
GAS DRYER
METAL STUD
5/8" CONCRETE BACKER BOARD
THINSET
TILE
MORTAR BED
STONE SLAB CURB
LOOSE GRAVEL AT
WEEP HOLES
LIGHTWEIGHT
CONCRETE FILL
CONCRETE SLAB
FLASHING CLAMP
WITH WEEP HOLES
CASE MOLDING
STOP MOLDING
3/4" STONE SLAB
THRESHOLD
DOOR
3/4" WOOD FLOOR
1" X 6" WOOD SUBFLOOR
ON DIAGONAL
2" X 6" SLEEPERS
4"6"6"1"
13"
'FLY ASH'
LIGHTWEIGHT
CONCRETE FILL
CONCRETE 'PACKING'
ALIGN 1/2" OFFSET
1/2" UNDERCUT
POURED CONCRETE
SHOWER CURB
LEAD PAN WRAPPING
AROUND CURB
3"
SLOPE TO DRAIN
6"
SLOPE TO WASTE RISER
'DOUBLE DRAIN SYSTEM'
SHOWER DRAIN
PLASTER CEILING
'VIRGIN' LEAD PAN LINER
LATICRETE '9235'
WATERPROOF
MEMBRANE
NOTE:
LEAD PAN (4 LBS./FT.) EXTENDED OVER CURB AND 6" UP WALLS (CORNERS SOLDERED). FIFTEEN
POUND ROOFING FELT BETWEEN PAN AND CONCRETE. PLUG DRAIN AND TEST FOR
WATERTIGHTNESS FOR 24 HRS. COAT PAN TO PREVENT ELECTROLYSIS AND CORROSION.
ONLY USE 'VIRGIN' LEAD, NOT RECYCLED OR RECAST LEAD.
SHOWER DRAIN-WATERPROOFING DETAIL (SCALE:NTS)
3/4" STONE SADDLE
DOOR BUCK
DOOR
DOOR FRAME
1/2" CARPET
CARPET GLUE
8" CONCRETE SLAB
1/8" FOAM SOUND
INSULATION OR LATICRETE
'9235' IN KITCHEN
3/4" GLUE-DOWN WOOD
FLOORING
8" CONCRETE SLAB
1/8" THINSET MORTAR
LATICRETE '9235' WATERPROOF
MEMBRANE
'WARMLY YOURS' 'TEMPZONE'
ELECTRIC FLOOR HEATING SYSTEM
(IN BATHROOMS ONLY TYPE 'B1')
8" CONCRETE SLAB
1/4" LATICRETE '254 PLATINUM'
THINSET MORTAR
1/2" STONE FLOORING
LATICRETE 'SPECTRALOCK PRO'
GROUT
1/2" CARPET
1/2" CARPET UNDERPAD
CARPET TACK STRIP
WOOD FLOORING GLUE
8" CONCRETE SLAB
PUBLIC HALLWAY
TYPE 'A'
TYPE 'B' - WITH SOUND PROOFING
TYPE 'B1' - WITH FLOOR HEATING SYSTEM
TYPE 'D'
FLOOR TYPE DETAILS (SCALE: NTS)
EXISTING STONE SADDLE
THINSET
EXISTING TO REMAIN
1
4"8"
LINE OF TOP EDGE OF WATERPROOFING MEMBRANE 12" ABOVE FLOOR
AND TO CEILING AROUND SHOWER AND TUB.
NOTE: WATERPROOFING TO EXTEND IN PARTITION
WALLS UNDER IN-WALL TOILET TANKS.
LATICRETE '9235' WATERPROOF
MEMBRANE
TYPE 'C' - WITHOUT WATERPROOFING
TYPE 'C1' - WITH WATERPROOFING
LATICRETE '170' SOUNDPROOFING
MAT HELD OFF THE PERIMETER
WALLS WITH AN ISOLATION STRIP.
HOUSING MAINTENANCE NOTES:
1. PREMISES TO COMPLY WITH ARTICLE 17 HMC FOR HEAT AND HOT WATER.
2. PAINTING OF COMMON AND CORE SPACES AND APARTMENT INTERIORS SHALL COMPLY WITH SECTIONS D26-13.03 AND D26-13.05 OF
THE HMC.
3. PREMISES TO BE MAINTAINED AND KEPT FREE OF RODENT AND INSECT INFESTATION AS PER SECTIONS D26-13-14.03 AND D26-14.05 OF
THE HMC.
4. RECEPTACLES FOR COLLECTION OF WASTE MATTER TO BE PROVIDED A PER SECTION D26-14.03 OF THE HMC.
5. PROPER ELECTRIC LIGHTING EQUIPMENT WITHIN DWELLING UNITS TO BE PROVIDED AND MAINTAINED AS PER SECTION D26-19.01,
19.03 AND 19.04 OF THE HMC.
6. PEEP HOLES SHALL BE APPROVED BOARD OF STANDARDS AND APPEALS TYPE, SET 5 FT. ABOVE THE FINISHED FLOOR, SET INTO THE
DWELLING UNIT DOOR, AS PER SECTION D26-01 OF THE HMC.
7. REGISTRATION STATEMENT TO BE FILED AS PER SECTION D26-41.01 AND 41.15 OF THE HMC.
8. REGISTRATION IDENTIFICATION ILLUSTRATING THE BUILDING IDENTIFICATION NUMBER SHALL BE POSTED AS PER SECTION D26-41.15
OF THE HMC.
9. INTERCOM/BELL AND BUZZER SYSTEM TO BE INSTALLED AS PER SECTION C26 604.4(2) AND SECTION 57 MDL.
10. FACILITIES AND EQUIPMENT SHALL COMPLY WITH D26-32.01 OF THE HMC.
11. LIGHTING AND VENTILATION SHALL COMPLY WITH D26-32.03 OF THE HMC.
12. NO KITCHEN SHALL BE OCCUPIED FOR SLEEPING PURPOSES PURSUANT TO SECTION D26-33.05 OF THE HMC.
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
3. NORTH
CLOSETCLOSET
CLOSET CLOSET
CLOSET
CLOSET
LAUNDRY
FOYER
LIVING ROOM
NO WORK
DINING ROOM
NO WORK
APT 10A
ENTRANCE
EXISTING
F.P.S.C.
LEGEND:
EXISTING WALLS OR ELEMENTS TO REMAIN.
EXISTING NON -BEARING WALLS OR ELEMENTS TO BE REMOVED.
NEW FULL HEIGHT WALL: 2 1/2" METAL STUDS @ 16" O.C.WITH ONE
LAYER 5/8" TYPE-X GYPSUM BOARD EACH SIDE
(ALIGN THICKNESS TO ADJACENT WALLS AS REQUIRED) UNO.
SMOKE/ CO DETECTOR
MASTER BATHBATH 2
EXISTING
F.P.S.C.
fridge
washer/dryer
DW
KITCHEN
W
V
C
H
STEAM RISER
REMOVE EXISTING
RADITIORS AND CAP
LINES AT THE RISER
W
V
C
H
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
4. NORTH
CLOSET
LAUNDRY
FOYER
MASTER BEDROOM
LIVING ROOM
NO WORK
DINING ROOM
NO WORK
BEDROOM 2
APT 10A
ENTRANCE
EXISTING
F.P.S.C.
CLOSET
CLOSET
LEGEND:
EXISTING WALLS OR ELEMENTS TO REMAIN.
EXISTING NON -BEARING WALLS OR ELEMENTS TO BE REMOVED.
NEW FULL HEIGHT WALL: 2 1/2" METAL STUDS @ 16" O.C.WITH ONE
LAYER 5/8" TYPE-X GYPSUM BOARD EACH SIDE
(ALIGN THICKNESS TO ADJACENT WALLS AS REQUIRED) UNO.
SMOKE/ CO DETECTOR
SH 31
WH 64
SD
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 48
WH 47
SH 48
WH 47
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
MASTER BATHBATH 2
SD
SD
SD
SD
REF
W/D
DW
EXISTING
F.P.S.C.
ROOF LEADER TO
REMAIN
UNDER CABINET
LIGHTS
SH 31
WH 64
SH 31
WH 64
SH 48
WH 47
WOOD FLOOR
EXISTING
WOOD FLOOR
EXISTINGWOOD FLOOR
EXISTING
WOOD FLOOR
EXISTING
WOOD FLOOR
EXISTING
TILE FLOOR
TYPE B
KITCHEN
TILE FLOOR
TYPE B
2
1
4
4 4
1 EXISTING TILE FLOOR TO REMAIN
NOTES
3 STAINLESS STEEL PAN UNDER WASHER
NEW COMBINATION FITTING WITH 1/2" C/H WATER SUPPLY WITH CHECK
VALVES AND 2" WASTE AND LEAK DETECTOR SHUT-OFF. WASHER DRYER
SHUT-OFFS WILL BE ACCESSIBLE WITHOUGH MOVING UNITS.
4 PERIMETER OF WATERPROOF MEMBRANE
5
5 5
STEAM RISER
W
V
C
H
ACCESS PANEL
PLUMBING NOTES:
a REPLACE EXISTING TOILETS, SINKS AND SHOWER IN EXISTING
LOCATIONS EXISITNG TUB TO REMAIN.
b. NEW AND RELOCATED TOILETS: NEW 1/2" COLD WATER SUPPLY
WITH CHECK VALVE. PROVIDE NEW BRANCH LINES FOR SUPPLY,
WASTE AND VENT BACK TO RISERS WITH SHUT-OFFS AT RISER
c. NEW AND RELOCATED SINKS AND FAUCETS: CHECK VALVES ON
H&C SUPPLY LINE. PROVIDE NEW BRANCH LINES FOR SUPPLY
WASTE AND VENT BACK TO RISERS WITH SHUT-OFFS AT RISER
d. ALL CABINETRY : FUTURE REMOVABLE CABINETRY AS PER LL
58/87 COMPLIANCE REQUIREMENTS.
e. WATERPROOFING FOR ALL BATHS AND LAUNDRY :LATICRETE
9325 ON FULL WALLS IN SHOWER AND UP TO 12" ON ALL
OTHERS- SEE SHOWER/FLOOR DETAIL G-002.
f. AT REMOVED WC, REMOVED LEAD BEND AND CAP CAST IRON
LINE AT RISER. REMOVE ALL EXISTING BRANCH LINES AND
INSTALL NEW STANDPIPE AND NEW WATER SUPPLY FROM RISER
FOR WASHER DRYER.
EX'G RADIATOR EX'G RADIATOR
EX'GRADIATOREX'GRADIATOR
6 6
'WARMLY YOURS' RADIANT HEAT FLOORING
6
TILE FLOOR
TYPE B1
TILE FLOOR
TYPE B1
TILE FLOOR
TYPE B1
LOCATION OF GAS
METER IN UPPER
CABINET TO REMAIN
3
2 APPROPRIATE EXISTING DRYER VENTING IN EXISTING
DROPPED CEILING FOR USE WITH NEW DRYER
HOLD EXISTING
CLEARANCE
BETWEEN CABINETS
AND WINDOWSFOR
PROPER OPERATION
NEW RADIANT HEAT
FLOORING
GAS LINE TO DRYER
TO RUN THROUGH
EXISTING DROPPED
CEILING
F
W
V
C
H
EX'GRADIATOR
EX'G RADIATOREX'G RADIATOR
CLOSET
CLOSET
SH 31
WH 64
SH 31
WH 64
SH 48
WH 47
SH 48
WH 47
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
5. NORTH
LAUNDRY
FOYER
LIVING ROOM
NO WORK
DINING ROOM
NO WORK
APT 10A
ENTRANCE
EXISTING
F.P.S.C.
CLOSET
LEGEND:
EXISTING WALLS OR ELEMENTS TO REMAIN.
EXISTING NON -BEARING WALLS OR ELEMENTS TO BE REMOVED.
NEW FULL HEIGHT WALL: 2 1/2" METAL STUDS @ 16" O.C.WITH ONE
LAYER 5/8" TYPE-X GYPSUM BOARD EACH SIDE
(ALIGN THICKNESS TO ADJACENT WALLS AS REQUIRED) UNO.
SMOKE/ CO DETECTOR
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 48
WH 47
SH 48
WH 47
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
MASTER BATHBATH 2
REF
W/D
DW
EXISTING
F.P.S.C.
ROOF LEADER TO
REMAIN
UNDER CABINET
LIGHTS
SH 31
WH 64
SH 31
WH 64
SH 48
WH 47
KITCHEN
STEAM RISER
W
V
C
H
ACCESS PANEL
EX'G RADIATOR EX'G RADIATOR
EX'GRADIATOREX'GRADIATOR
NOTE: REPLACE EXISTING LIGHT FIXTURES IN EXISTING LOCATIONS WHERE
SHOWN. NO CHANNELING IN CEILINGS OR EXTERIOR OR DEMISING WALLS.
NO DROPPED CEILINGS WILL BE CREATED. ONLY NEW WALL-MOUNTED
LIGHTING TO BE USED IN NEW WALLS.
ELECTRICAL LEGEND:
LIGHT SWITCH
3 WAY SWITCH
JAMB SWITCH
SINGLE RECEPTACLE
WALL MOUNTED LIGHT
SURFACE MOUNTED CEILING LIGHT
DUPLEX RECEPTACLE
GFI DUPLEX RECEPTACLE
QUADRAPLEX RECEPTACLE
RECESSED LIGHT
UNDER CABINET LIGHT
NEW RADIANT HEAT
FLOORING
W
V
C
H
EX'GRADIATOR
EX'G RADIATOREX'G RADIATOR
CLOSET
CLOSET
SH 31
WH 64
SH 31
WH 64
SH 48
WH 47
SH 48
WH 47
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
7. NORTH
CLOSETCLOSET
CLOSET CLOSET
CLOSET
CLOSET
LAUNDRY
FOYER
LIVING ROOM
NO WORK
DINING ROOM
NO WORK
APT 10A
ENTRANCE
EXISTING
F.P.S.C.
CLOSET
LEGEND:
EXISTING WALLS OR ELEMENTS TO REMAIN.
EXISTING NON -BEARING WALLS OR ELEMENTS TO BE REMOVED.
NEW FULL HEIGHT WALL: 2 1/2" METAL STUDS @ 16" O.C.WITH ONE
LAYER 5/8" TYPE-X GYPSUM BOARD EACH SIDE
(ALIGN THICKNESS TO ADJACENT WALLS AS REQUIRED) UNO.
SMOKE/ CO DETECTOR
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 48
WH 47
SH 48
WH 47
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
MASTER BATHBATH 2
EXISTING
F.P.S.C.
fridge
washer/dryer
DW
ROOF LEADER TO
REMAIN
UNDER CABINET
LIGHTS
SH 31
WH 64
SH 31
WH 64
SH 48
WH 47
KITCHEN
STEAM RISER
W
V
C
H
ACCESS PANEL
EX'G RADIATOR EX'G RADIATOR
EX'GRADIATOREX'GRADIATOR
STEAM RISER
REMOVE EXISTING
RADITIORS AND CAP
LINES AT THE RISER
NEW RADIANT HEAT
FLOORING
W
V
C
H
EX'GRADIATOR
EX'G RADIATOREX'G RADIATOR
CLOSET
CLOSET
SH 31
WH 64
SH 31
WH 64
SH 48
WH 47
SH 48
WH 47
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
BH 103"
BH 103"
BH 103.75"
BH 103.75"
BH 97"
BH 103.5"
BH 103.5"
BH 99.5"
BH103.75"
BH103.75"
BH103.75"
BH103.5"
BH104"
BH103"
Drawn By: Reviewed By:
Scale:Date:
Project:
Drawing Title:
DateNo. Description
DateNo. Description
Seal & Signature
Issued
Revised
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
8. NORTH
LAUNDRY
FOYER
LIVING ROOM
NO WORK
DINING ROOM
NO WORK
APT 10A
ENTRANCE
EXISTING
F.P.S.C.
CLOSET
LEGEND:
EXISTING WALLS OR ELEMENTS TO REMAIN.
EXISTING NON -BEARING WALLS OR ELEMENTS TO BE REMOVED.
NEW FULL HEIGHT WALL: 2 1/2" METAL STUDS @ 16" O.C.WITH ONE
LAYER 5/8" TYPE-X GYPSUM BOARD EACH SIDE
(ALIGN THICKNESS TO ADJACENT WALLS AS REQUIRED) UNO.
SMOKE/ CO DETECTOR
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 48
WH 47
SH 48
WH 47
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
MASTER BATHBATH 2
REF
W/D
DW
EXISTING
F.P.S.C.
ROOF LEADER TO
REMAIN
UNDER CABINET
LIGHTS
SH 31
WH 64
SH 31
WH 64
SH 48
WH 47
KITCHEN
STEAM RISER
W
V
C
H
ACCESS PANEL
EX'G RADIATOR EX'G RADIATOR
EX'GRADIATOREX'GRADIATOR
NOTE: REPLACE EXISTING LIGHT FIXTURES IN EXISTING LOCATIONS WHERE
SHOWN. NO CHANNELING IN CEILINGS OR EXTERIOR OR DEMISING WALLS.
NO DROPPED CEILINGS WILL BE CREATED. ONLY NEW WALL-MOUNTED
LIGHTING TO BE USED IN NEW WALLS.
ELECTRICAL LEGEND:
LIGHT SWITCH
3 WAY SWITCH
JAMB SWITCH
SINGLE RECEPTACLE
WALL MOUNTED LIGHT
SURFACE MOUNTED CEILING LIGHT
DUPLEX RECEPTACLE
GFI DUPLEX RECEPTACLE
QUADRAPLEX RECEPTACLE
RECESSED LIGHT
UNDER CABINET LIGHT
NEW RADIANT HEAT
FLOORING
W
V
C
H
BH 103"
BH 103"
BH 103.75"
BH 103.75"
BH 97"
BH 103.5"
BH 103.5"
BH 99.5"
BH103.75"
BH103.75"
BH103.75"
BH103.5"
BH104"
BH103"
Drawn By: Reviewed By:
Scale:Date:
Project:
Drawing Title:
DateNo. Description
DateNo. Description
Seal & Signature
Issued
Revised
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
9. NORTH
LAUNDRY
FOYER
LIVING ROOM
NO WORK
DINING ROOM
NO WORK
APT 10A
ENTRANCE
EXISTING
F.P.S.C.
CLOSET
LEGEND:
EXISTING WALLS OR ELEMENTS TO REMAIN.
EXISTING NON -BEARING WALLS OR ELEMENTS TO BE REMOVED.
NEW FULL HEIGHT WALL: 2 1/2" METAL STUDS @ 16" O.C.WITH ONE
LAYER 5/8" TYPE-X GYPSUM BOARD EACH SIDE
(ALIGN THICKNESS TO ADJACENT WALLS AS REQUIRED) UNO.
SMOKE/ CO DETECTOR
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 48
WH 47
SH 48
WH 47
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
MASTER BATHBATH 2
REF
W/D
DW
EXISTING
F.P.S.C.
ROOF LEADER TO
REMAIN
UNDER CABINET
LIGHTS
SH 31
WH 64
SH 31
WH 64
SH 48
WH 47
KITCHEN
STEAM RISER
W
V
C
H
ACCESS PANEL
EX'G RADIATOR EX'G RADIATOR
EX'GRADIATOREX'GRADIATOR
NEW RADIANT HEAT
FLOORING
W
V
C
H
BH 103"
BH 103"
BH 103.75"
BH 103.75"
BH 97"
BH 103.5"
BH 103.5"
BH 99.5"
BH103.75"
BH103.75"
BH103.75"
BH103.5"
BH104"
BH103"
Drawn By: Reviewed By:
Scale:Date:
Project:
Drawing Title:
DateNo. Description
DateNo. Description
Seal & Signature
Issued
Revised
A-2
1
A-3
1
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
10. W
V
C
H
EX'G RADIATOR
CLOSET
CLOSET
SH 31
WH 64
SH 31
WH 64
SH 48
WH 47
BH 103"
BH 103"
Drawn By: Reviewed By:
Scale:Date:
Project:
Drawing Title:
DateNo. Description
DateNo. Description
Seal & Signature
Issued
Revised
1 3/8" = 1'-0"
BEDROOM 2/BATHROOM 2
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
11. W
V
C
H
EX'GRADIATOR
CLOSET
SH 48
WH 47
SH 48
WH 47
SH 31
WH 64
SH 31
WH 64
SH 31
WH 64
BH 97"
BH 103.5"
BH 103.5"
Drawn By: Reviewed By:
Scale:Date:
Project:
Drawing Title:
DateNo. Description
DateNo. Description
Seal & Signature
Issued
Revised
1 3/8" = 1'-0"
MASTER BATH/MASTER BEDROOM
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
12. Drawn By: Reviewed By:
Scale:Date:
Project:
Drawing Title:
DateNo. Description
DateNo. Description
Seal & Signature
Issued
Revised
1 1/2" = 1'-0"
NORTH ELEVATION BATHROOM 2
2 1/2" = 1'-0"
EAST ELEVATION BATHROOM 2
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
13. Drawn By: Reviewed By:
Scale:Date:
Project:
Drawing Title:
DateNo. Description
DateNo. Description
Seal & Signature
Issued
Revised
1/2" = 1'-0"
SOUTH ELEVATION BATHROOM 2
4 1/2" = 1'-0"
WEST ELEVATION BATHROOM 2
3
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
14. Drawn By: Reviewed By:
Scale:Date:
Project:
Drawing Title:
DateNo. Description
DateNo. Description
Seal & Signature
Issued
Revised
1 1/2" = 1'-0"
NORTH ELEVATION MASTER BATHROOM
2 1/2" = 1'-0"
EAST ELEVATION MASTER BATHROOM
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
15. Drawn By: Reviewed By:
Scale:Date:
Project:
Drawing Title:
DateNo. Description
DateNo. Description
Seal & Signature
Issued
Revised
1/2" = 1'-0"
SOUTH ELEVATION MASTER BATHROOM
4 1/2" = 1'-0"
WEST ELEVATION MASTER BATHROOM
3
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
16. Drawn By: Reviewed By:
Scale:Date:
Project:
Drawing Title:
DateNo. Description
DateNo. Description
Seal & Signature
Issued
Revised
1 1/2" = 1'-0"
EAST ELEVATION OPTION #1 - 3"X6"
2 1/2" = 1'-0"
EAST ELEVATION OPTION #2 - 4.25"x8.5"
1/2" = 1'-0"
EAST ELEVATION OPTION #3 - 8"x2.5"
3
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
17. Drawn By: Reviewed By:
Scale:Date:
Project:
Drawing Title:
DateNo. Description
DateNo. Description
Seal & Signature
Issued
Revised
1 3/8" = 1'-0"
NORTH ELEVATION LIVING ROOM
2 3/8" = 1'-0"
EAST ELEVATION DINING ROOM
3 3/8" = 1'-0"
NORTH ELEVATION MASTER BEDROOM
2 3/8" = 1'-0"
EAST ELEVATION BEDROOM 2
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
18. Drawn By: Reviewed By:
Scale:Date:
Project:
Drawing Title:
DateNo. Description
DateNo. Description
Seal & Signature
Issued
Revised
1 3/8" = 1'-0"
SOUTH ELEVATION LIVING ROOM
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCEDBYANAUTODESKEDUCATIONALPRODUCT
PRODUCED BY AN AUTODESK EDUCATIONAL PRODUCT
