PSM Chemical Plant NEP UPDATE March 2011
•Download as PPT, PDF•
1 like•940 views
This document summarizes inspection data from the OSHA Chemical PSM National Emphasis Program. It shows that 151 inspections were opened, with 96 resulting in citations. On average, inspections found 9 citations per inspection, with average penalties of $25,129 per inspection. The most common citations were for mechanical integrity, process safety information, and process hazard analysis requirements. Common violations involved procedures, documentation, hazard analysis and safety reviews. The data provides insights into emphasis areas and compliance issues under the OSHA PSM standard.
Report
Share
Report
Share
Recommended
Costs of falls and workerscomp
This document analyzes workers' compensation data from 2005-2007 on falls among roofers and carpenters in 38 states. It finds that falls from elevations for roofers cost on average $54 million annually, with average claims costing $106,000 each. For carpenters, falls from elevations cost approximately $93 million annually, with average claims costing over $97,000. Falls from ladders or scaffolds by roofers cost around $19 million annually on average, with claims costing about $68,000 each. For carpenters, such falls cost approximately $64 million annually, with average claims at nearly $62,000.
Amuay ucve aug 25, 2012
An explosion occurred at an olefins plant in Amuay, Venezuela on August 25, 2012 around 1:10 AM. Olefins were being produced on site and stored in spherical tanks. There was a leak from an olefins pump that was not properly addressed for days. Atmospheric conditions caused the wind to slow and change direction, preventing dispersion of the leaking vapors. This led to a build up of an ignitable vapor cloud. It is believed a vehicle ignited the cloud, causing an explosion that killed 51 people and injured many others. The explosion was the result of an unconfined vapor cloud explosion (UVCE) where the rapid combustion of the cloud generated a powerful pressure wave without confinement.
Flat roofing safety 10 31 11 short
This document discusses fall protection safety for roofing work. It outlines OSHA's mission to ensure safe working conditions and prevent injuries. It then lists some injury prevention basics like management leadership, hazard prevention, education and training programs. It notes that over 1000 roofing deaths have occurred since 2000. The document highlights the most frequently cited OSHA standards and violations, with issues like fall protection, machine guarding, and lockout/tagout being common. It includes photos illustrating unsafe and safe work practices regarding fall protection on roofs.
Ohio manufacturers fy12 m cfinal v2 10 7-2011
The document summarizes OSHA's activities and priorities in Region V including Ohio from fiscal years 2007 to 2011. It discusses increased inspections, emphasis on high risk industries, and efforts to change workplace culture through stronger enforcement and compliance assistance. Key statistics provided include inspection numbers, most frequently cited violations, and details on enforcement programs targeting severe and repeat violators.
Pascual Imec06
The document discusses optimization of inspection decisions for safety systems. It notes that up to 40% of failure modes in safety systems are hidden and require failure finding tasks. The document then outlines factors to consider in developing reliability models for safety systems, including different failure modes, redundancy, common cause failures, and imperfect inspections. The goal is to estimate optimal inspection intervals to maximize overall availability and safety availability of safety systems. An example is provided of analyzing inspection intervals for a two-out-of-three pressure vessel safety system.
Performance results and their drivers
This document summarizes performance metrics and their drivers for a company from 2010 to 2016. Key metrics showed improvements in lost time incident rate, chargeability, test delivery precision, machine inventory reduction, and prototype build quality and lead time. Initiatives contributing to these gains included implementing KEMS, safety programs, strategic planning, cross-site working groups, lean principles training, and visual management systems.
Eurocontrol Sqs
The document discusses safety management activities within the European Air Traffic Management Programme (EATMP). It outlines that EATMP focuses on developing guidance materials, providing support and training to help implement safety management systems. This includes initiatives to help states monitor safety and improve reporting of incidents, as well as developing methodologies to assess the safety of new ATM systems throughout their lifecycle. The overall goal is to enhance safety by promoting a culture of safety management across European air traffic management.
Quality Control Progress 2014
The quality plan for 2014 aims to improve color management through using pressSIGN software and TECKON measurement devices. This is expected to raise quality levels by 30% from international standards, increase customer and employee satisfaction, reduce make-ready time by 30%, and OK sheet time by 50%. Using advanced global technology will help boost operator confidence and sense of belonging through self-training. It will also increase trust among current and prospective customers by adding value.
Recommended
Costs of falls and workerscomp
This document analyzes workers' compensation data from 2005-2007 on falls among roofers and carpenters in 38 states. It finds that falls from elevations for roofers cost on average $54 million annually, with average claims costing $106,000 each. For carpenters, falls from elevations cost approximately $93 million annually, with average claims costing over $97,000. Falls from ladders or scaffolds by roofers cost around $19 million annually on average, with claims costing about $68,000 each. For carpenters, such falls cost approximately $64 million annually, with average claims at nearly $62,000.
Amuay ucve aug 25, 2012
An explosion occurred at an olefins plant in Amuay, Venezuela on August 25, 2012 around 1:10 AM. Olefins were being produced on site and stored in spherical tanks. There was a leak from an olefins pump that was not properly addressed for days. Atmospheric conditions caused the wind to slow and change direction, preventing dispersion of the leaking vapors. This led to a build up of an ignitable vapor cloud. It is believed a vehicle ignited the cloud, causing an explosion that killed 51 people and injured many others. The explosion was the result of an unconfined vapor cloud explosion (UVCE) where the rapid combustion of the cloud generated a powerful pressure wave without confinement.
Flat roofing safety 10 31 11 short
This document discusses fall protection safety for roofing work. It outlines OSHA's mission to ensure safe working conditions and prevent injuries. It then lists some injury prevention basics like management leadership, hazard prevention, education and training programs. It notes that over 1000 roofing deaths have occurred since 2000. The document highlights the most frequently cited OSHA standards and violations, with issues like fall protection, machine guarding, and lockout/tagout being common. It includes photos illustrating unsafe and safe work practices regarding fall protection on roofs.
Ohio manufacturers fy12 m cfinal v2 10 7-2011
The document summarizes OSHA's activities and priorities in Region V including Ohio from fiscal years 2007 to 2011. It discusses increased inspections, emphasis on high risk industries, and efforts to change workplace culture through stronger enforcement and compliance assistance. Key statistics provided include inspection numbers, most frequently cited violations, and details on enforcement programs targeting severe and repeat violators.
Pascual Imec06
The document discusses optimization of inspection decisions for safety systems. It notes that up to 40% of failure modes in safety systems are hidden and require failure finding tasks. The document then outlines factors to consider in developing reliability models for safety systems, including different failure modes, redundancy, common cause failures, and imperfect inspections. The goal is to estimate optimal inspection intervals to maximize overall availability and safety availability of safety systems. An example is provided of analyzing inspection intervals for a two-out-of-three pressure vessel safety system.
Performance results and their drivers
This document summarizes performance metrics and their drivers for a company from 2010 to 2016. Key metrics showed improvements in lost time incident rate, chargeability, test delivery precision, machine inventory reduction, and prototype build quality and lead time. Initiatives contributing to these gains included implementing KEMS, safety programs, strategic planning, cross-site working groups, lean principles training, and visual management systems.
Eurocontrol Sqs
The document discusses safety management activities within the European Air Traffic Management Programme (EATMP). It outlines that EATMP focuses on developing guidance materials, providing support and training to help implement safety management systems. This includes initiatives to help states monitor safety and improve reporting of incidents, as well as developing methodologies to assess the safety of new ATM systems throughout their lifecycle. The overall goal is to enhance safety by promoting a culture of safety management across European air traffic management.
Quality Control Progress 2014
The quality plan for 2014 aims to improve color management through using pressSIGN software and TECKON measurement devices. This is expected to raise quality levels by 30% from international standards, increase customer and employee satisfaction, reduce make-ready time by 30%, and OK sheet time by 50%. Using advanced global technology will help boost operator confidence and sense of belonging through self-training. It will also increase trust among current and prospective customers by adding value.
Risk analysis
This document provides an overview of risk analysis. It defines key terms like risk, risk analysis, risk assessment, and risk management. It describes various qualitative and quantitative methods used for risk analysis, including hazard and operability studies, fault tree analysis, failure mode and effects analysis. The document discusses the importance of risk analysis for chemical processes and highlights some historical accidents to emphasize this. It also provides examples of applying different risk analysis methods.
Requirements Engineering Best Practice
The document discusses requirements engineering best practices in the context of digital health projects. It provides data on the use of various requirements engineering techniques in over 400 projects. The most commonly used techniques include natural language requirements, functional requirements, workshops, system modeling, and reusing existing requirements. However, the techniques most strongly correlated with project success were establishing a clear business case, understanding user scenarios, and conducting stakeholder workshops. The document advocates for an experimental approach to requirements engineering involving iterative experiments with stakeholders.
6Sigma
The document contains reliability data for various pieces of equipment from January to June. It shows the unplanned downtime, number of failures, total working hours, and calculated reliability percentage for each month. Additional charts show the unplanned maintenance downtime and downtime ratio for each month, with calculations to determine control limits. Root cause analysis was performed for main failures on a fan, identifying bearing issues as the primary cause. Recommendations are provided to shift to a more preventive maintenance approach through techniques like TPM to improve reliability.
ACI_CP_1_38th_Edition_Concrete_Field_Testing_Technician—Grade_I.pdf
This document provides information about ACI's certification program for Concrete Field Testing Technicians - Grade 1. It outlines the purpose and importance of certification, giving technicians opportunities for advancement. It also describes the administration and requirements to obtain certification, including passing both a written and performance exam. Certification helps ensure the proper performance of concrete tests, improving quality control and allowing for timely identification of non-compliant concrete.
Achieving ss thru_fta
The document summarizes a study conducted by a manufacturing plant to improve quality and achieve Six Sigma levels of production. The plant used a cross-functional team and fault tree analysis to model their processes. They identified key areas for improvement, such as procedures and human factors. Fault trees were quantified using failure rate data to prioritize actions. The analysis helped identify weaknesses and priorities for future quality projects. It provided justification for improvements by quantitatively defining the impact on off-spec production rates.
Q7 a
The document outlines quality assurance guidelines for active pharmaceutical ingredients (APIs) as per cGMP regulations. It covers topics such as quality management, personnel qualifications, facility design, utilities, documentation, materials management, production processes, packaging and labeling, storage, validation, change control, and more. The key points are that manufacturers must establish a quality management system involving management participation to ensure APIs meet quality standards, maintain independent quality control units, document all quality-related activities, and conduct periodic reviews and audits.
M&E Key Performance Indicators 2016
The document provides objectives and key performance indicators for various divisions within an aircraft maintenance and engineering department. It includes objectives related to operational performance, workforce development, cost reduction, growth, and social responsibility. Specific divisional objectives relate to areas like aircraft airworthiness, line maintenance, base maintenance, maintenance control center, ground support services, technical planning, fleet technical management, and quality/safety. Key performance indicators include metrics like delays, documentation errors, equipment availability, forecast accuracy, and safety incidents. Progress is measured monthly and divisions are given grades based on targets for each objective.
Risk management in complex changeovers through cfmea
Keywords: changeover, set-up cost, product lead time, severity, FMEA, failure modes and effects analysis, risk ranking table, SMED, single minute exchange of die, economic batch quantity, die casting machines, non-value adding activities
Risk Management in Sterile Environments
The two most commonly used within microbiology are
HACCP (which originated in the food industry) and FMEA
(developed for engineering). This article explores these two
approaches, first with a description of HACCP, followed by a
description and case study of FMEA in sterility testing.
Cem com example-qa_qc_plan
This QA/QC plan provides guidelines for maintaining the quality of data from CEMS and COMS systems at a power plant. It outlines responsibilities for communication, documentation, training, quality control activities like calibration and audits, preventative maintenance, and corrective actions. The goal is to ensure emission data meets applicable regulations and permits.
Condition-Based Maintenance Basics by Carl Byington - PHM Design, LLC
Condition-based maintenance (CBM or CBM+) is a strategy of performing maintenance on a machine or system only when there is objective evidence of need or impending failure. CBM is enabled by the evolution of key technologies, including improvements in - sensors, microprocessors, digital signal processing, simulation modeling, multisensor data fusion, reliability engineering, Internet of Things (IoT) connectivity, data warehousing, cloud computing, machine learning (ML), artificial intelligence (AI), and predictive analytics. CBM involves monitoring the health or performance of a component or system and performing maintenance based on that inferred health and in some cases, predicted remaining useful life (RUL). This predictive maintenance philosophy contrasts with earlier ideologies, such as corrective maintenance — in which action is taken after a component or system fails — and preventive maintenance — which is based on event or time milestones. Each involves a cost tradeoff.
Carl Byington with PHM Design, LLC reviews some of the elements of CBM.
#phmdesign
https://phmdesign.com
NCQC Knowledge Test 08
This document contains a 20 question multiple choice knowledge test on quality control concepts for a Quality Circle. The questions cover topics such as control charts, process capability, total quality management, six sigma methodology, and statistical process control. An answer key is provided for participants to self-grade the test after completion. The test was compiled by Dinesh Sharma on October 30th, 2018 and is intended to be completed within 20 minutes.
FMEA.pdf
1. The document provides an overview of core tool training for APQP, FMEA, and PPAP processes. It discusses the history and benefits of failure mode and effects analysis (FMEA) and outlines the FMEA process.
2. Key aspects of FMEA covered include potential failure modes, effects analysis, risk priority numbers, design controls, process controls, continuous improvement, and management responsibility.
3. Examples of potential failure modes, effects, and process steps from a sample PFMEA are also provided to demonstrate how to complete an FMEA.
Test Metrics
The document discusses metrics for tracking a project's test management process. It provides examples of metrics that could be captured at different stages of the testing lifecycle, including test execution rates, defect rates, requirements tracing, and environment issues. Guidelines are also presented for establishing a process to define, collect, analyze, and report on metrics on a regular basis to improve visibility and decision making.
Viva voce 17 may 2018
This research presentation summarizes a study on process safety management (PSM) among offshore production platform workers in Peninsular Malaysia. The objectives were to understand workers' current knowledge of PSM, perceptions of difficulty of PSM elements, and ratings of current safety culture. A questionnaire was distributed to workers and results were analyzed using statistical methods. Key findings included non-technical workers having the lowest understanding of PSM, finding certain PSM elements like equipment identification and permit-to-work most difficult to implement, and ratings of safety culture being higher among technical crews who work in multiple facilities. The discussion suggests improving PSM training for non-technical workers.
Burant, Larry resume 01_2014
Lawrence Burant has over 30 years of experience in statistical engineering, quality assurance, and continuous improvement. He has a background in various industries including aerospace, automotive, medical devices, and industrial automation. Burant holds multiple certifications including Six Sigma Black Belt, Certified Quality Engineer, and Certified Lead Auditor for ISO and AS standards. Throughout his career, he has spearheaded numerous projects that resulted in improved quality, increased yields, reduced costs and failures, and enhanced customer satisfaction.
Pid controller mcq answers
This document contains 31 multiple choice questions related to control systems and controllers. The questions cover topics such as:
- The relationship between steady-state error, gain, and oscillations for proportional controllers.
- Design criteria for PID controllers including quarter-amplitude decay ratio and Zeigler-Nichols method.
- Phenomena related to switching between manual and automatic modes.
- Definitions of proportional band, proportional gain, reset control, and integral control.
- Applications and effects of P, PI, PD, and PID controllers.
- Characteristics and uses of proportional, integral, and derivative controllers.
The document concludes by providing the solutions to each multiple choice question.
3 psm process_hazard_analysis2
The document discusses Process Hazard Analysis (PHA) and Management of Change requirements under the Process Safety Management standard. It emphasizes that PHA is the most difficult but important part of implementing PSM, as it identifies hazards and safeguards. The PHA must address all equipment, processes, incidents, controls, and consequences of failure. Management of Change procedures are also required to manage any changes to the covered process system and ensure related documentation and training are updated. The PHA and MOC work together to identify hazards, implement prevention, and manage any necessary changes to the process safely.
Thesis MSC
This thesis studied risks, safety climate, safety management practices, and situation awareness in offshore environments. It had four main objectives: 1) assess risks of offshore drilling and production platforms, 2) evaluate safety climate and safety management practices, 3) identify root causes of offshore accidents, and 4) examine safety and situation awareness of offshore crews. Various methods were used, including risk assessment techniques, a safety climate assessment toolkit, an accident root cause model, and interviews with offshore personnel. Key findings included identifying major hazards for offshore platforms, assessing the current safety climate and practices of companies, determining root causes of accidents, and factors affecting crew situation awareness. The study provided recommendations to improve offshore safety and risk management.
MultivariableProcessIdentificationforMPC-TheAsymptoticMethodanditsApplication...
The document introduces the asymptotic method (ASYM) of identification for developing multivariable process models to be used in model predictive control (MPC). ASYM calculates parametric time-domain models from frequency domain data in a systematic way that solves issues like test design, model structure selection, and error quantification. It can provide both process and disturbance models along with error bounds useful for validation and robustness analysis. The document demonstrates ASYM on a distillation column benchmark process and a crude oil unit for MPC.
Applicability of caa section112(r) & general duty clause
This document provides an overview of the US EPA Region 5 Risk Management Program. It discusses the applicability of the Clean Air Act Section 112(r) and the general duty clause. It also describes the 40 CFR Part 68 Risk Management Program rule requirements including regulated substances, threshold criteria, exemptions, and the three program levels. Finally, it provides contact information for the Michigan RMP program.
Costs of falls and workerscomp
This document analyzes workers' compensation data from 2005-2007 on falls among roofers and carpenters in 38 states. It finds that falls from elevations for roofers cost on average $54 million annually, with average claims costing $106,000 each. For carpenters, falls from elevations cost approximately $93 million annually, with average claims costing over $97,000. Falls from ladders or scaffolds by roofers cost around $19 million annually on average, with claims costing about $68,000 each. For carpenters, such falls cost approximately $64 million annually, with average claims at nearly $62,000.
More Related Content
Similar to PSM Chemical Plant NEP UPDATE March 2011
Risk analysis
This document provides an overview of risk analysis. It defines key terms like risk, risk analysis, risk assessment, and risk management. It describes various qualitative and quantitative methods used for risk analysis, including hazard and operability studies, fault tree analysis, failure mode and effects analysis. The document discusses the importance of risk analysis for chemical processes and highlights some historical accidents to emphasize this. It also provides examples of applying different risk analysis methods.
Requirements Engineering Best Practice
The document discusses requirements engineering best practices in the context of digital health projects. It provides data on the use of various requirements engineering techniques in over 400 projects. The most commonly used techniques include natural language requirements, functional requirements, workshops, system modeling, and reusing existing requirements. However, the techniques most strongly correlated with project success were establishing a clear business case, understanding user scenarios, and conducting stakeholder workshops. The document advocates for an experimental approach to requirements engineering involving iterative experiments with stakeholders.
6Sigma
The document contains reliability data for various pieces of equipment from January to June. It shows the unplanned downtime, number of failures, total working hours, and calculated reliability percentage for each month. Additional charts show the unplanned maintenance downtime and downtime ratio for each month, with calculations to determine control limits. Root cause analysis was performed for main failures on a fan, identifying bearing issues as the primary cause. Recommendations are provided to shift to a more preventive maintenance approach through techniques like TPM to improve reliability.
ACI_CP_1_38th_Edition_Concrete_Field_Testing_Technician—Grade_I.pdf
This document provides information about ACI's certification program for Concrete Field Testing Technicians - Grade 1. It outlines the purpose and importance of certification, giving technicians opportunities for advancement. It also describes the administration and requirements to obtain certification, including passing both a written and performance exam. Certification helps ensure the proper performance of concrete tests, improving quality control and allowing for timely identification of non-compliant concrete.
Achieving ss thru_fta
The document summarizes a study conducted by a manufacturing plant to improve quality and achieve Six Sigma levels of production. The plant used a cross-functional team and fault tree analysis to model their processes. They identified key areas for improvement, such as procedures and human factors. Fault trees were quantified using failure rate data to prioritize actions. The analysis helped identify weaknesses and priorities for future quality projects. It provided justification for improvements by quantitatively defining the impact on off-spec production rates.
Q7 a
The document outlines quality assurance guidelines for active pharmaceutical ingredients (APIs) as per cGMP regulations. It covers topics such as quality management, personnel qualifications, facility design, utilities, documentation, materials management, production processes, packaging and labeling, storage, validation, change control, and more. The key points are that manufacturers must establish a quality management system involving management participation to ensure APIs meet quality standards, maintain independent quality control units, document all quality-related activities, and conduct periodic reviews and audits.
M&E Key Performance Indicators 2016
The document provides objectives and key performance indicators for various divisions within an aircraft maintenance and engineering department. It includes objectives related to operational performance, workforce development, cost reduction, growth, and social responsibility. Specific divisional objectives relate to areas like aircraft airworthiness, line maintenance, base maintenance, maintenance control center, ground support services, technical planning, fleet technical management, and quality/safety. Key performance indicators include metrics like delays, documentation errors, equipment availability, forecast accuracy, and safety incidents. Progress is measured monthly and divisions are given grades based on targets for each objective.
Risk management in complex changeovers through cfmea
Keywords: changeover, set-up cost, product lead time, severity, FMEA, failure modes and effects analysis, risk ranking table, SMED, single minute exchange of die, economic batch quantity, die casting machines, non-value adding activities
Risk Management in Sterile Environments
The two most commonly used within microbiology are
HACCP (which originated in the food industry) and FMEA
(developed for engineering). This article explores these two
approaches, first with a description of HACCP, followed by a
description and case study of FMEA in sterility testing.
Cem com example-qa_qc_plan
This QA/QC plan provides guidelines for maintaining the quality of data from CEMS and COMS systems at a power plant. It outlines responsibilities for communication, documentation, training, quality control activities like calibration and audits, preventative maintenance, and corrective actions. The goal is to ensure emission data meets applicable regulations and permits.
Condition-Based Maintenance Basics by Carl Byington - PHM Design, LLC
Condition-based maintenance (CBM or CBM+) is a strategy of performing maintenance on a machine or system only when there is objective evidence of need or impending failure. CBM is enabled by the evolution of key technologies, including improvements in - sensors, microprocessors, digital signal processing, simulation modeling, multisensor data fusion, reliability engineering, Internet of Things (IoT) connectivity, data warehousing, cloud computing, machine learning (ML), artificial intelligence (AI), and predictive analytics. CBM involves monitoring the health or performance of a component or system and performing maintenance based on that inferred health and in some cases, predicted remaining useful life (RUL). This predictive maintenance philosophy contrasts with earlier ideologies, such as corrective maintenance — in which action is taken after a component or system fails — and preventive maintenance — which is based on event or time milestones. Each involves a cost tradeoff.
Carl Byington with PHM Design, LLC reviews some of the elements of CBM.
#phmdesign
https://phmdesign.com
NCQC Knowledge Test 08
This document contains a 20 question multiple choice knowledge test on quality control concepts for a Quality Circle. The questions cover topics such as control charts, process capability, total quality management, six sigma methodology, and statistical process control. An answer key is provided for participants to self-grade the test after completion. The test was compiled by Dinesh Sharma on October 30th, 2018 and is intended to be completed within 20 minutes.
FMEA.pdf
1. The document provides an overview of core tool training for APQP, FMEA, and PPAP processes. It discusses the history and benefits of failure mode and effects analysis (FMEA) and outlines the FMEA process.
2. Key aspects of FMEA covered include potential failure modes, effects analysis, risk priority numbers, design controls, process controls, continuous improvement, and management responsibility.
3. Examples of potential failure modes, effects, and process steps from a sample PFMEA are also provided to demonstrate how to complete an FMEA.
Test Metrics
The document discusses metrics for tracking a project's test management process. It provides examples of metrics that could be captured at different stages of the testing lifecycle, including test execution rates, defect rates, requirements tracing, and environment issues. Guidelines are also presented for establishing a process to define, collect, analyze, and report on metrics on a regular basis to improve visibility and decision making.
Viva voce 17 may 2018
This research presentation summarizes a study on process safety management (PSM) among offshore production platform workers in Peninsular Malaysia. The objectives were to understand workers' current knowledge of PSM, perceptions of difficulty of PSM elements, and ratings of current safety culture. A questionnaire was distributed to workers and results were analyzed using statistical methods. Key findings included non-technical workers having the lowest understanding of PSM, finding certain PSM elements like equipment identification and permit-to-work most difficult to implement, and ratings of safety culture being higher among technical crews who work in multiple facilities. The discussion suggests improving PSM training for non-technical workers.
Burant, Larry resume 01_2014
Lawrence Burant has over 30 years of experience in statistical engineering, quality assurance, and continuous improvement. He has a background in various industries including aerospace, automotive, medical devices, and industrial automation. Burant holds multiple certifications including Six Sigma Black Belt, Certified Quality Engineer, and Certified Lead Auditor for ISO and AS standards. Throughout his career, he has spearheaded numerous projects that resulted in improved quality, increased yields, reduced costs and failures, and enhanced customer satisfaction.
Pid controller mcq answers
This document contains 31 multiple choice questions related to control systems and controllers. The questions cover topics such as:
- The relationship between steady-state error, gain, and oscillations for proportional controllers.
- Design criteria for PID controllers including quarter-amplitude decay ratio and Zeigler-Nichols method.
- Phenomena related to switching between manual and automatic modes.
- Definitions of proportional band, proportional gain, reset control, and integral control.
- Applications and effects of P, PI, PD, and PID controllers.
- Characteristics and uses of proportional, integral, and derivative controllers.
The document concludes by providing the solutions to each multiple choice question.
3 psm process_hazard_analysis2
The document discusses Process Hazard Analysis (PHA) and Management of Change requirements under the Process Safety Management standard. It emphasizes that PHA is the most difficult but important part of implementing PSM, as it identifies hazards and safeguards. The PHA must address all equipment, processes, incidents, controls, and consequences of failure. Management of Change procedures are also required to manage any changes to the covered process system and ensure related documentation and training are updated. The PHA and MOC work together to identify hazards, implement prevention, and manage any necessary changes to the process safely.
Thesis MSC
This thesis studied risks, safety climate, safety management practices, and situation awareness in offshore environments. It had four main objectives: 1) assess risks of offshore drilling and production platforms, 2) evaluate safety climate and safety management practices, 3) identify root causes of offshore accidents, and 4) examine safety and situation awareness of offshore crews. Various methods were used, including risk assessment techniques, a safety climate assessment toolkit, an accident root cause model, and interviews with offshore personnel. Key findings included identifying major hazards for offshore platforms, assessing the current safety climate and practices of companies, determining root causes of accidents, and factors affecting crew situation awareness. The study provided recommendations to improve offshore safety and risk management.
MultivariableProcessIdentificationforMPC-TheAsymptoticMethodanditsApplication...
The document introduces the asymptotic method (ASYM) of identification for developing multivariable process models to be used in model predictive control (MPC). ASYM calculates parametric time-domain models from frequency domain data in a systematic way that solves issues like test design, model structure selection, and error quantification. It can provide both process and disturbance models along with error bounds useful for validation and robustness analysis. The document demonstrates ASYM on a distillation column benchmark process and a crude oil unit for MPC.
Similar to PSM Chemical Plant NEP UPDATE March 2011 (20)
ACI_CP_1_38th_Edition_Concrete_Field_Testing_Technician—Grade_I.pdf
ACI_CP_1_38th_Edition_Concrete_Field_Testing_Technician—Grade_I.pdf
Risk management in complex changeovers through cfmea
Risk management in complex changeovers through cfmea
Condition-Based Maintenance Basics by Carl Byington - PHM Design, LLC
Condition-Based Maintenance Basics by Carl Byington - PHM Design, LLC
MultivariableProcessIdentificationforMPC-TheAsymptoticMethodanditsApplication...
MultivariableProcessIdentificationforMPC-TheAsymptoticMethodanditsApplication...
More from Bryan Haywood
Applicability of caa section112(r) & general duty clause
This document provides an overview of the US EPA Region 5 Risk Management Program. It discusses the applicability of the Clean Air Act Section 112(r) and the general duty clause. It also describes the 40 CFR Part 68 Risk Management Program rule requirements including regulated substances, threshold criteria, exemptions, and the three program levels. Finally, it provides contact information for the Michigan RMP program.
Costs of falls and workerscomp
This document analyzes workers' compensation data from 2005-2007 on falls among roofers and carpenters in 38 states. It finds that falls from elevations for roofers cost on average $54 million annually, with average claims costing $106,000 each. For carpenters, falls from elevations cost approximately $93 million annually, with average claims costing over $97,000. Falls from ladders or scaffolds by roofers cost around $19 million annually on average, with claims costing about $68,000 each. For carpenters, such falls cost approximately $64 million annually, with average claims at nearly $62,000.
Gi2011hotworks abridged
An explosion occurred during routine maintenance on a water pipe at a Colombian power station, killing eight workers. The CSB has identified over 60 fatalities since 1990 due to explosions and fires from hot work activities like welding and cutting. Proper hot work safety programs include evaluating the work, requiring permits, monitoring the atmosphere for hazards, clearing the area of combustibles, providing fire watches, and training workers. An accident occurred when welders were not informed of explosive materials in a slurry tank and the tank atmosphere was not monitored prior to welding.
Boiler safety 11 28 2011 abridged
A $1.6 million settlement was reached in a boiler explosion case where a man suffered severe injuries. Boiler explosions and fires have injured many people in the last ten years due to lack of safety training. A 1999 explosion at a power plant killed 6 people and injured 30. Proper boiler safety requires management leadership, hazard prevention, education and training to prevent accidents. The top causes of boiler accidents are issues with maintenance, lockout procedures during startup, falls, carbon monoxide exposure, and fly ash hazards.
Frac tank explosion_steps
Four frac tank explosions occurred over two incidents due to static electricity buildup during air/foam assisted flowback operations. Static was generated as oil, water, gas, and sediment flowed through pipes at high velocity into lined, non-grounded frac tanks. This prevented static discharge and led to sparks when the electric charge jumped the gap between charged liquids in the tank and protruding downcomers. To prevent future explosions, operators should use open-top gas buster systems to reduce fluid velocity, allow static dissipation, and prevent accumulation of flammable gas mixtures at tank hatches.
Gi2011machineguard
This document discusses the history of machine guarding from the pre-industrial era through modern safety codes and regulations. It notes that as the industrial revolution increased powered machinery injuries, public reaction and labor unions pushed for laws requiring guarding of hazardous machines. The document provides examples of common machine hazards and injuries as well as guidelines for proper guarding techniques based on OSHA regulations.
Hats of test 03 compatable
Upon passing a series of tests on one's head, including immersion in water, withstanding impacts from an eight pound steel ball dropped from 15 feet, exposure to acids and solvents, resistance to a propane torch, and sustaining 2,200 volts of electricity, one would receive a certificate stating their head meets ANSI safety standards and does not require wearing a hard hat on the jobsite. The tests subject the head to a range of temperatures from -20 to 140 degrees Fahrenheit. For those unsure if their head can pass the tests, wearing a hard hat is recommended for protection.
Safety Culture (Unknown Source)
1) Achieving zero incidents is possible through developing a strong safety culture where safety is the top priority and responsibility of all employees and managers. This requires clear communication from top management about the need for culture change.
2) A safety culture focuses on eliminating the root causes of incidents rather than just reactions. It views safety as an integral part of business operations and empowers employees to take responsibility for safety.
3) Key elements of an effective safety culture include management commitment, well-defined safety policies and goals, employee training, hazard analysis, and recognizing employees for safe behaviors. With the right systems and commitment from all levels, any organization can achieve an incident-free work environment.
Gi forklift 7 27 2011
A great presentation provided by John Newquist, Assistant Regional Administrator at DOL-OSHA (Region V)
Ladders 5 31 11
Over 1000 deaths have occurred since 2000 relating to ladder use. Falls are the largest risk factor. 91 of the 101 deaths in 2010 were due to falls, with distances ranging from under 6 feet to over 40 feet. Training employees on proper ladder setup and fall protection can prevent many accidents. Alternatives to ladders such as aerial lifts should be considered when practical to eliminate fall risks.
RMP e-Submit Webinar Presentation
This is the presentation from the EPA Webinar for how to use the e-Submit program to submit your facility's Risk Management Plan.
More from Bryan Haywood (11)
Applicability of caa section112(r) & general duty clause
Applicability of caa section112(r) & general duty clause
Recently uploaded
Innovation Management Frameworks: Your Guide to Creativity & Innovation
Innovation Management Frameworks: Your Guide to Creativity & InnovationOperational Excellence Consulting
[To download this presentation, visit:
https://www.oeconsulting.com.sg/training-presentations]
This PowerPoint compilation offers a comprehensive overview of 20 leading innovation management frameworks and methodologies, selected for their broad applicability across various industries and organizational contexts. These frameworks are valuable resources for a wide range of users, including business professionals, educators, and consultants.
Each framework is presented with visually engaging diagrams and templates, ensuring the content is both informative and appealing. While this compilation is thorough, please note that the slides are intended as supplementary resources and may not be sufficient for standalone instructional purposes.
This compilation is ideal for anyone looking to enhance their understanding of innovation management and drive meaningful change within their organization. Whether you aim to improve product development processes, enhance customer experiences, or drive digital transformation, these frameworks offer valuable insights and tools to help you achieve your goals.
INCLUDED FRAMEWORKS/MODELS:
1. Stanford’s Design Thinking
2. IDEO’s Human-Centered Design
3. Strategyzer’s Business Model Innovation
4. Lean Startup Methodology
5. Agile Innovation Framework
6. Doblin’s Ten Types of Innovation
7. McKinsey’s Three Horizons of Growth
8. Customer Journey Map
9. Christensen’s Disruptive Innovation Theory
10. Blue Ocean Strategy
11. Strategyn’s Jobs-To-Be-Done (JTBD) Framework with Job Map
12. Design Sprint Framework
13. The Double Diamond
14. Lean Six Sigma DMAIC
15. TRIZ Problem-Solving Framework
16. Edward de Bono’s Six Thinking Hats
17. Stage-Gate Model
18. Toyota’s Six Steps of Kaizen
19. Microsoft’s Digital Transformation Framework
20. Design for Six Sigma (DFSS)
To download this presentation, visit:
https://www.oeconsulting.com.sg/training-presentationsHow HR Search Helps in Company Success.pdf
HR search is critical to a company's success because it ensures the correct people are in place. HR search integrates workforce capabilities with company goals by painstakingly identifying, screening, and employing qualified candidates, supporting innovation, productivity, and growth. Efficient talent acquisition improves teamwork while encouraging collaboration. Also, it reduces turnover, saves money, and ensures consistency. Furthermore, HR search discovers and develops leadership potential, resulting in a strong pipeline of future leaders. Finally, this strategic approach to recruitment enables businesses to respond to market changes, beat competitors, and achieve long-term success.
一比一原版(QMUE毕业证书)英国爱丁堡玛格丽特女王大学毕业证文凭如何办理
永久可查学历认证【微信：A575476】【(QMUE毕业证书)英国爱丁堡玛格丽特女王大学毕业证成绩单Offer】【微信：A575476】（留信学历认证永久存档查询）采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
【业务选择办理准则】
一、工作未确定，回国需先给父母、亲戚朋友看下文凭的情况，办理一份就读学校的毕业证【微信：A575476】文凭即可
二、回国进私企、外企、自己做生意的情况，这些单位是不查询毕业证真伪的，而且国内没有渠道去查询国外文凭的真假，也不需要提供真实教育部认证。鉴于此，办理一份毕业证【微信：A575476】即可
三、进国企，银行，事业单位，考公务员等等，这些单位是必需要提供真实教育部认证的，办理教育部认证所需资料众多且烦琐，所有材料您都必须提供原件，我们凭借丰富的经验，快捷的绿色通道帮您快速整合材料，让您少走弯路。
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
→ 【关于价格问题（保证一手价格）
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
选择实体注册公司办理，更放心，更安全！我们的承诺：可来公司面谈，可签订合同，会陪同客户一起到教育部认证窗口递交认证材料，客户在教育部官方认证查询网站查询到认证通过结果后付款，不成功不收费！
Brian Fitzsimmons on the Business Strategy and Content Flywheel of Barstool S...
On episode 272 of the Digital and Social Media Sports Podcast, Neil chatted with Brian Fitzsimmons, Director of Licensing and Business Development for Barstool Sports.
What follows is a collection of snippets from the podcast. To hear the full interview and more, check out the podcast on all podcast platforms and at www.dsmsports.net
Part 2 Deep Dive: Navigating the 2024 Slowdown
Introduction
The global retail industry has weathered numerous storms, with the financial crisis of 2008 serving as a poignant reminder of the sector's resilience and adaptability. However, as we navigate the complex landscape of 2024, retailers face a unique set of challenges that demand innovative strategies and a fundamental shift in mindset. This white paper contrasts the impact of the 2008 recession on the retail sector with the current headwinds retailers are grappling with, while offering a comprehensive roadmap for success in this new paradigm.
DearbornMusic-KatherineJasperFullSailUni
My powerpoint presentation for my Music Retail and Distribution class at Full Sail University
Garments ERP Software in Bangladesh _ Pridesys IT Ltd.pdf
Pridesys Garments ERP is one of the leading ERP solution provider, especially for Garments industries which is integrated with
different modules that cover all the aspects of your Garments Business. This solution supports multi-currency and multi-location
based operations. It aims at keeping track of all the activities including receiving an order from buyer, costing of order, resource
planning, procurement of raw materials, production management, inventory management, import-export process, order
reconciliation process etc. It’s also integrated with other modules of Pridesys ERP including finance, accounts, HR, supply-chain etc.
With this automated solution you can easily track your business activities and entire operations of your garments manufacturing
proces
Digital Transformation Frameworks: Driving Digital Excellence
[To download this presentation, visit:
https://www.oeconsulting.com.sg/training-presentations]
This presentation is a curated compilation of PowerPoint diagrams and templates designed to illustrate 20 different digital transformation frameworks and models. These frameworks are based on recent industry trends and best practices, ensuring that the content remains relevant and up-to-date.
Key highlights include Microsoft's Digital Transformation Framework, which focuses on driving innovation and efficiency, and McKinsey's Ten Guiding Principles, which provide strategic insights for successful digital transformation. Additionally, Forrester's framework emphasizes enhancing customer experiences and modernizing IT infrastructure, while IDC's MaturityScape helps assess and develop organizational digital maturity. MIT's framework explores cutting-edge strategies for achieving digital success.
These materials are perfect for enhancing your business or classroom presentations, offering visual aids to supplement your insights. Please note that while comprehensive, these slides are intended as supplementary resources and may not be complete for standalone instructional purposes.
Frameworks/Models included:
Microsoft’s Digital Transformation Framework
McKinsey’s Ten Guiding Principles of Digital Transformation
Forrester’s Digital Transformation Framework
IDC’s Digital Transformation MaturityScape
MIT’s Digital Transformation Framework
Gartner’s Digital Transformation Framework
Accenture’s Digital Strategy & Enterprise Frameworks
Deloitte’s Digital Industrial Transformation Framework
Capgemini’s Digital Transformation Framework
PwC’s Digital Transformation Framework
Cisco’s Digital Transformation Framework
Cognizant’s Digital Transformation Framework
DXC Technology’s Digital Transformation Framework
The BCG Strategy Palette
McKinsey’s Digital Transformation Framework
Digital Transformation Compass
Four Levels of Digital Maturity
Design Thinking Framework
Business Model Canvas
Customer Journey Map
NIMA2024 | De toegevoegde waarde van DEI en ESG in campagnes | Nathalie Lam |...
Nathalie zal delen hoe DEI en ESG een fundamentele rol kunnen spelen in je merkstrategie en je de juiste aansluiting kan creëren met je doelgroep. Door middel van voorbeelden en simpele handvatten toont ze hoe dit in jouw organisatie toegepast kan worden.
Zodiac Signs and Food Preferences_ What Your Sign Says About Your Taste
Know what your zodiac sign says about your taste in food! Explore how the 12 zodiac signs influence your culinary preferences with insights from MyPandit. Dive into astrology and flavors!
The Most Inspiring Entrepreneurs to Follow in 2024.pdf
In a world where the potential of youth innovation remains vastly untouched, there emerges a guiding light in the form of Norm Goldstein, the Founder and CEO of EduNetwork Partners. His dedication to this cause has earned him recognition as a Congressional Leadership Award recipient.
Sustainable Logistics for Cost Reduction_ IPLTech Electric's Eco-Friendly Tra...
Sustainable Logistics for Cost Reduction_ IPLTech Electric's Eco-Friendly Transport Solution
The latest Heat Pump Manual from Newentide
𝐔𝐧𝐯𝐞𝐢𝐥 𝐭𝐡𝐞 𝐅𝐮𝐭𝐮𝐫𝐞 𝐨𝐟 𝐄𝐧𝐞𝐫𝐠𝐲 𝐄𝐟𝐟𝐢𝐜𝐢𝐞𝐧𝐜𝐲 𝐰𝐢𝐭𝐡 𝐍𝐄𝐖𝐍𝐓𝐈𝐃𝐄’𝐬 𝐋𝐚𝐭𝐞𝐬𝐭 𝐎𝐟𝐟𝐞𝐫𝐢𝐧𝐠𝐬
Explore the details in our newly released product manual, which showcases NEWNTIDE's advanced heat pump technologies. Delve into our energy-efficient and eco-friendly solutions tailored for diverse global markets.
一比一原版新西兰奥塔哥大学毕业证（otago毕业证）如何办理
一模一样【微信：A575476】【新西兰奥塔哥大学毕业证（otago毕业证）成绩单Offer】【微信：A575476】（留信学历认证永久存档查询）采用学校原版纸张、特殊工艺完全按照原版一比一制作（包括：隐形水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠，文字图案浮雕，激光镭射，紫外荧光，温感，复印防伪）行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备，十五年致力于帮助留学生解决难题，业务范围有加拿大、英国、澳洲、韩国、美国、新加坡，新西兰等学历材料，包您满意。
【业务选择办理准则】
一、工作未确定，回国需先给父母、亲戚朋友看下文凭的情况，办理一份就读学校的毕业证【微信：A575476】文凭即可
二、回国进私企、外企、自己做生意的情况，这些单位是不查询毕业证真伪的，而且国内没有渠道去查询国外文凭的真假，也不需要提供真实教育部认证。鉴于此，办理一份毕业证【微信：A575476】即可
三、进国企，银行，事业单位，考公务员等等，这些单位是必需要提供真实教育部认证的，办理教育部认证所需资料众多且烦琐，所有材料您都必须提供原件，我们凭借丰富的经验，快捷的绿色通道帮您快速整合材料，让您少走弯路。
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
→ 【关于价格问题（保证一手价格）
我们所定的价格是非常合理的，而且我们现在做得单子大多数都是代理和回头客户介绍的所以一般现在有新的单子 我给客户的都是第一手的代理价格，因为我想坦诚对待大家 不想跟大家在价格方面浪费时间
对于老客户或者被老客户介绍过来的朋友，我们都会适当给一些优惠。
选择实体注册公司办理，更放心，更安全！我们的承诺：可来公司面谈，可签订合同，会陪同客户一起到教育部认证窗口递交认证材料，客户在教育部官方认证查询网站查询到认证通过结果后付款，不成功不收费！
The Genesis of BriansClub.cm Famous Dark WEb Platform
BriansClub.cm, a famous platform on the dark web, has become one of the most infamous carding marketplaces, specializing in the sale of stolen credit card data.
TIMES BPO: Business Plan For Startup Industry
Starting a business is like embarking on an unpredictable adventure. It’s a journey filled with highs and lows, victories and defeats. But what if I told you that those setbacks and failures could be the very stepping stones that lead you to fortune? Let’s explore how resilience, adaptability, and strategic thinking can transform adversity into opportunity.
Digital Marketing with a Focus on Sustainability
Digital Marketing best practices including influencer marketing, content creators, and omnichannel marketing for Sustainable Brands at the Sustainable Cosmetics Summit 2024 in New York
How are Lilac French Bulldogs Beauty Charming the World and Capturing Hearts....
“After being the most listed dog breed in the United States for 31
years in a row, the Labrador Retriever has dropped to second place
in the American Kennel Club's annual survey of the country's most
popular canines. The French Bulldog is the new top dog in the
United States as of 2022. The stylish puppy has ascended the
rankings in rapid time despite having health concerns and limited
color choices.”
Dpboss Matka Guessing Satta Matta Matka Kalyan panel Chart Indian Matka Dpbos...
Dpboss Matka Guessing Satta Matta Matka Kalyan panel Chart Indian Matka Dpbos...➒➌➎➏➑➐➋➑➐➐Dpboss Matka Guessing Satta Matka Kalyan Chart Indian Matka
Sattamatka.satta.matka.satta matka.kalyan weekly chart.kalyan chart.kalyan jodi chart.kalyan penal chart.kalyan today.kalyan open.fix satta.fix fix fix Satta matka nambarRecently uploaded (20)
Innovation Management Frameworks: Your Guide to Creativity & Innovation
Innovation Management Frameworks: Your Guide to Creativity & Innovation
Brian Fitzsimmons on the Business Strategy and Content Flywheel of Barstool S...
Brian Fitzsimmons on the Business Strategy and Content Flywheel of Barstool S...
Garments ERP Software in Bangladesh _ Pridesys IT Ltd.pdf
Garments ERP Software in Bangladesh _ Pridesys IT Ltd.pdf
Digital Transformation Frameworks: Driving Digital Excellence
Digital Transformation Frameworks: Driving Digital Excellence
NIMA2024 | De toegevoegde waarde van DEI en ESG in campagnes | Nathalie Lam |...
NIMA2024 | De toegevoegde waarde van DEI en ESG in campagnes | Nathalie Lam |...
Zodiac Signs and Food Preferences_ What Your Sign Says About Your Taste
Zodiac Signs and Food Preferences_ What Your Sign Says About Your Taste
The Most Inspiring Entrepreneurs to Follow in 2024.pdf
The Most Inspiring Entrepreneurs to Follow in 2024.pdf
Sustainable Logistics for Cost Reduction_ IPLTech Electric's Eco-Friendly Tra...
Sustainable Logistics for Cost Reduction_ IPLTech Electric's Eco-Friendly Tra...
The Genesis of BriansClub.cm Famous Dark WEb Platform
The Genesis of BriansClub.cm Famous Dark WEb Platform
How are Lilac French Bulldogs Beauty Charming the World and Capturing Hearts....
How are Lilac French Bulldogs Beauty Charming the World and Capturing Hearts....
Dpboss Matka Guessing Satta Matta Matka Kalyan panel Chart Indian Matka Dpbos...
Dpboss Matka Guessing Satta Matta Matka Kalyan panel Chart Indian Matka Dpbos...
PSM Chemical Plant NEP UPDATE March 2011
- 2. An Update on OSHA’s Chemical PSM National Emphasis Program
- 4. Chem NEP Inspections – Facility Type
- 5. Chem NEP Inspections – Facility Type
- 6. Chem NEP Inspections – Facility Type
- 7. Chem NEP Citations by PSM Element Element Description % of PSM Citations Cumulative % j Mechanical Integrity 22.5% 22.5% d Process Safety Information 21.6% 44.1% e Process Hazard Analysis 17.9% 62.1% f Operating Procedures 12.1% 74.1% g Training 4.4% 78.5% l Management of Change 4.3% 82.8% h Contractors 3.5% 86.3% o Compliance Audits 3.5% 89.9% c Employee participation 3.0% 92.9% m Incident Investigation 2.5% 95.4% n Emergency Planning & Response 2.3% 97.7% i Pre-startup Review 1.6% 99.3% k Hot Work 0.7% 100.0%
- 8. Chem NEP Citations by PSM Element
- 9. Chem NEP Citations by OSHA Standard Sub-element Sub-element Description % All Citations Cumulative % 119(d)(3)(ii) PSI RAGAGEP 3.8% 3.8% 119(j)(2) MI written procedures 3.8% 7.5% 119(j)(4)(i) MI I&T performed 2.2% 9.7% 119(e)(5) PHA findings & recommendations 2.0% 11.7% 119(j)(4)(iii) I&T frequency 2.0% 13.7% 29(b)(1) Mobile ladders and scaffolds 1.9% 15.6% 119(j)(5) MI equipment deficiencies 1.8% 17.4% 119(d)(3)(i)(B) PSI P&IDs 1.6% 19.0% 119(j)(4)(iv) MI I&T documentation 1.6% 20.6% 119(n) Emergency Planning & Response 1.6% 22.2% 119(o)(1) Compliance Audits performed 1.6% 23.9% 119(e)(1) PHAs performed 1.5% 25.3% 119(e)(3)(iii) PHA engineering controls 1.5% 26.8% 119(f)(3) Operating Procedures certification 1.5% 28.3%
- 10. Chem NEP Citations by OSHA Standard Sub-element (continued) Sub-element Description % All Citations Cumulative % 119(f)(4) OP safe work practices 1.5% 29.8% 151(c) Eyewash stations (mostly NH3) 1.5% 31.3% 119(l)(1) MOC not performed 1.3% 32.6% GDC General Duty Clause (wide variety) 1.2% 33.8% 23(c)(1) Guarding floor openings 1.2% 35.0% 119(f)(1) OP not developed & implemented 1.2% 36.3% 119(g)(1)(i) Initial Training 1.2% 37.5% 119(e)(3)(i) PHA - address hazards of process 1.1% 38.5% 119(e)(6) PHA - reval at least every 5 years 1.1% 39.6% 119(d)(3)(i)(D) PSI - relief system des & des basis 0.9% 40.6% 119(d)(3)(i)(E) PSI - ventilation system design 0.9% 41.5%
- 11. Chem NEP Citations by OSHA Standard Sub-element
Editor's Notes
- A total of 416 PSM citations have been proposed, out of 742 total
- Many PPE standards also cited.