This document summarizes research on using a microwave dehydrator system to improve the demulsification of petroleum emulsions. The system consists of a modified microwave oven and silicone-based chemical demulsifiers. Experimental emulsions with varying water content and additive concentration were tested. Results showed the microwave dehydrator can maximize water separation within 2 minutes of irradiation, using 0.1% additive concentration. This improves on conventional demulsification techniques by reducing chemical and processing costs while avoiding their environmental impacts. The microwave treatment works by heating the emulsion and neutralizing interfacial forces between water droplets, aiding their separation.
ELECTRICAL PROPERTIES OF NI0.4MG0.6FE2O4 SYNTHESIZED BY CONVENTIONAL SOLID-ST...IAEME Publication
Ni0.4Mg0.6Fe2O4 samples are prepared by conventional double sintering approach and sintered at 1300oC/ 2 h. These ferrites are characterized using X-ray diffractometer. The diffraction study reveals that the present compound shows perfect single phase cubic spinel structure. In addition, the behavior of distinct electrical properties such as dielectric constant (ε'), dielectric loss (ε") and ac-conductivity (σac) as a function frequency as well as temperature is analyzed using the LCR controller
The Futures of the Physic-Chemical and Thermoelectric Properties of the InTe-...theijes
By the methods of the physic-chemical analysis as well the measurements of microhadness and picknomentric density the semiconducting system InTe-Cu2ZnSnS4 has been investigated and its state diagram has been plotted. Guazibinarity of the system with restricted homogeneous fields has established on the basis of both initial components. The boundaries of solid solutions at 300K reach on side of InTe ~ 2mol% and on side of Cu2ZnSnS4 ~ 13mol%. The coordinates of the system eutectic correspond to the composition ~23mol% Cu2ZnSnS4 and temperature ~813K. A study of thermoelectric and galvanomagnetic parameters of solid solutions (InTe)1-x(Cu2ZnSnS4)x showed dispersion of electrons from the ionized admixture at low temperatures, and at higher temperatures from thermal vibrations of crystalline lattice. Heat transfer takes place according to one-phonon mechanism. The alloy of solid solution (InTe)0,98(Cu2ZnSnS4)0,02 possesses a high value of thermoelectric efficiency.
ELECTRICAL PROPERTIES OF NI0.4MG0.6FE2O4 SYNTHESIZED BY CONVENTIONAL SOLID-ST...IAEME Publication
Ni0.4Mg0.6Fe2O4 samples are prepared by conventional double sintering approach and sintered at 1300oC/ 2 h. These ferrites are characterized using X-ray diffractometer. The diffraction study reveals that the present compound shows perfect single phase cubic spinel structure. In addition, the behavior of distinct electrical properties such as dielectric constant (ε'), dielectric loss (ε") and ac-conductivity (σac) as a function frequency as well as temperature is analyzed using the LCR controller
The Futures of the Physic-Chemical and Thermoelectric Properties of the InTe-...theijes
By the methods of the physic-chemical analysis as well the measurements of microhadness and picknomentric density the semiconducting system InTe-Cu2ZnSnS4 has been investigated and its state diagram has been plotted. Guazibinarity of the system with restricted homogeneous fields has established on the basis of both initial components. The boundaries of solid solutions at 300K reach on side of InTe ~ 2mol% and on side of Cu2ZnSnS4 ~ 13mol%. The coordinates of the system eutectic correspond to the composition ~23mol% Cu2ZnSnS4 and temperature ~813K. A study of thermoelectric and galvanomagnetic parameters of solid solutions (InTe)1-x(Cu2ZnSnS4)x showed dispersion of electrons from the ionized admixture at low temperatures, and at higher temperatures from thermal vibrations of crystalline lattice. Heat transfer takes place according to one-phonon mechanism. The alloy of solid solution (InTe)0,98(Cu2ZnSnS4)0,02 possesses a high value of thermoelectric efficiency.
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Influence of input power in Ar/H2 thermal plasma with silicon powder by numer...TELKOMNIKA JOURNAL
Numerical simulation in inductively coupled thermal plasma was made on the temperature distribution in argon (Ar)+hydrogen (H2) induction thermal plasma torch with silicon (Si) powder injection to obtain the temperature distribution and gas flow fields. The ICTP model was used in this research because it has benefit of good repeatability and no contamination process. Interactions between ICTP and injected powder are very complicated to be understood only by related experiments. Influence of input power in ICTP was numerically investigated on thermal plasma temperature fields and powder evaporation. The temperature distributions of thermal plasma and Si vapor distribution were compared at input powers of 20 kW, 30 kW, and 40 kW. Results indicated that higher input power increases the temperature of the thermal plasma with doughnut shape but it slightly enhances evaporation of the powder at the center axis of the plasma torch.
Comparative study on ammonia sensing properties of sno2 nanocomposites fabric...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Moisture content investigation in the soil samples using microwave dielectric...IJECEIAES
The microwaves of typical frequency ranges of 3 GHz to 30 GHz have been in use for remote sensing applications which are progressing rapidly. The microwaves can sense existing moisture in any material that absorbs moisture such as soil or vegetation. In case of soils which may be comprised of variable mix proportionate of solids, liquids or gases and distinct textures subjected to the associated size and the arrangements of soil particles. Hence, the moisture absorption by a specific type of soil used to be different. The inherent physical and electrical properties such as color, texture, grains, dielectric constant, conductivity or permeability, etc. differentiate various soils. In this work, authors present soil moisture measurement by simple estimation of emissivity i.e. the ratio of energy radiated by an object to absorbing the body of same physical temperature. A strategic method of measuring dielectric constant using a microwave signal is used in this research work. The measurement of the dielectric constant of the soils collected from the specific regions and analysis of results has been reported. The proposed method is less complex and can further be used for the identification of soil moisture and agricultural applications.
Spectroscopic Properties of Ho3+ Doped Zinc Lithium Bismuth Borate Glassesinventionjournals
Zinc lithium bismuth borate glasses containing Ho3+ in (25- x): Bi2O3:20Li2O:20ZnO: 35B2O3:xHo2O3 (where x=1, 1.5,2 mol %) have been prepared by melt-quenching method. The amorphous nature of the glasses was confirmed by x-ray diffraction studies. Optical absorption spectra were recorded at room temperature for all glass samples. The experimental oscillator strengths were calculated from the area under the absorption bands. Slater-Condon parameter F2, Lande’s parameter ξ4f, Nephlauxetic ratio (β’) and Bonding parameter (b ½ ) have been computed. Using these parameters energies and intensities of these bands has been calculated. Judd-Ofelt intensity parameters Ωλ (λ=2, 4, 6) are evaluated from the intensities of various absorption bands of optical absorption spectra. Using these intensity parameters various radiative properties like spontaneous emission probability, branching ratio, radiative life time and stimulated emission cross– section of various emission lines have been evaluated.
Analysis of Electric Circuit Model on Atmospheric Pressure Dielectric Barrier...AM Publications
Analysis of Electric Circuit Model on Atmospheric Pressure Dielectric Barrier Discharge (DBD) Plasma has been simulated using the Simulink-Matlab R2010a software. Plasma reactor being used as the basis to determine the parameters in the circuit is in the coaxial form made of pyrex glass with an iron rod as the active electrode and spiral copper wire as passive electrode. The reactor was filled with argon gas with the flow rate of 2 L/s. Simulation circuit model which was prepared based on a DBD equivalent circuit, operated in a voltage range of 1.0 kV to 6.0 kV for frequency of 10 kHz to 66 kHz. Electrical characterization was performed to describe the plasma discharge that occurs in the reactor. The datas of supply voltage and current, as well as voltage and current discharge, was used to determine the average power during one period. From the simulation was obtained an increase in supply and discharge currents with increasing of frequency at the same operating voltage. Discharge power has increased in a specific voltage and increased frequency. It is obtained the average discharge power for 5.5 kV of 11.28 W and 10.90 W at a frequency of 21 kHz and 24 kHz, respectively. The highest efficiency obtained from the simulation that achieved at voltage of 1 kV and frequency of 45.7 kHz is equal to 56.59%.
Abstract: Nanotechnology is concerned with the materials and systems whose structures and components reveal novel and significantly improved physical, chemical, and biological properties, phenomena, and processes due to their micro size. Workforce development is needed to achieve the benefits of nanotechnology development along with technology transfer. The intensity should be on hands-on educational experiences by developing nano-tech laboratory demonstration experiments that could be adaptable and combined into existing courses in engineering and engineering technology. Theoretical heat transfer rates were calculated using existing relationships in the literature for conventional fluids and nano fluids. Experiments were conducted to determine the actual heat transfer rates under operational conditions using nanofluids and the heat transfer enhancement determined compared to fluids without nanoparticles.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Dispersion modeling of nitrous oxide emissions from a nitric acid plant in de...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
International Journal of Engineering Research and Applications (IJERA) is an open access online peer reviewed international journal that publishes research and review articles in the fields of Computer Science, Neural Networks, Electrical Engineering, Software Engineering, Information Technology, Mechanical Engineering, Chemical Engineering, Plastic Engineering, Food Technology, Textile Engineering, Nano Technology & science, Power Electronics, Electronics & Communication Engineering, Computational mathematics, Image processing, Civil Engineering, Structural Engineering, Environmental Engineering, VLSI Testing & Low Power VLSI Design etc.
Influence of input power in Ar/H2 thermal plasma with silicon powder by numer...TELKOMNIKA JOURNAL
Numerical simulation in inductively coupled thermal plasma was made on the temperature distribution in argon (Ar)+hydrogen (H2) induction thermal plasma torch with silicon (Si) powder injection to obtain the temperature distribution and gas flow fields. The ICTP model was used in this research because it has benefit of good repeatability and no contamination process. Interactions between ICTP and injected powder are very complicated to be understood only by related experiments. Influence of input power in ICTP was numerically investigated on thermal plasma temperature fields and powder evaporation. The temperature distributions of thermal plasma and Si vapor distribution were compared at input powers of 20 kW, 30 kW, and 40 kW. Results indicated that higher input power increases the temperature of the thermal plasma with doughnut shape but it slightly enhances evaporation of the powder at the center axis of the plasma torch.
Comparative study on ammonia sensing properties of sno2 nanocomposites fabric...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Moisture content investigation in the soil samples using microwave dielectric...IJECEIAES
The microwaves of typical frequency ranges of 3 GHz to 30 GHz have been in use for remote sensing applications which are progressing rapidly. The microwaves can sense existing moisture in any material that absorbs moisture such as soil or vegetation. In case of soils which may be comprised of variable mix proportionate of solids, liquids or gases and distinct textures subjected to the associated size and the arrangements of soil particles. Hence, the moisture absorption by a specific type of soil used to be different. The inherent physical and electrical properties such as color, texture, grains, dielectric constant, conductivity or permeability, etc. differentiate various soils. In this work, authors present soil moisture measurement by simple estimation of emissivity i.e. the ratio of energy radiated by an object to absorbing the body of same physical temperature. A strategic method of measuring dielectric constant using a microwave signal is used in this research work. The measurement of the dielectric constant of the soils collected from the specific regions and analysis of results has been reported. The proposed method is less complex and can further be used for the identification of soil moisture and agricultural applications.
Spectroscopic Properties of Ho3+ Doped Zinc Lithium Bismuth Borate Glassesinventionjournals
Zinc lithium bismuth borate glasses containing Ho3+ in (25- x): Bi2O3:20Li2O:20ZnO: 35B2O3:xHo2O3 (where x=1, 1.5,2 mol %) have been prepared by melt-quenching method. The amorphous nature of the glasses was confirmed by x-ray diffraction studies. Optical absorption spectra were recorded at room temperature for all glass samples. The experimental oscillator strengths were calculated from the area under the absorption bands. Slater-Condon parameter F2, Lande’s parameter ξ4f, Nephlauxetic ratio (β’) and Bonding parameter (b ½ ) have been computed. Using these parameters energies and intensities of these bands has been calculated. Judd-Ofelt intensity parameters Ωλ (λ=2, 4, 6) are evaluated from the intensities of various absorption bands of optical absorption spectra. Using these intensity parameters various radiative properties like spontaneous emission probability, branching ratio, radiative life time and stimulated emission cross– section of various emission lines have been evaluated.
Analysis of Electric Circuit Model on Atmospheric Pressure Dielectric Barrier...AM Publications
Analysis of Electric Circuit Model on Atmospheric Pressure Dielectric Barrier Discharge (DBD) Plasma has been simulated using the Simulink-Matlab R2010a software. Plasma reactor being used as the basis to determine the parameters in the circuit is in the coaxial form made of pyrex glass with an iron rod as the active electrode and spiral copper wire as passive electrode. The reactor was filled with argon gas with the flow rate of 2 L/s. Simulation circuit model which was prepared based on a DBD equivalent circuit, operated in a voltage range of 1.0 kV to 6.0 kV for frequency of 10 kHz to 66 kHz. Electrical characterization was performed to describe the plasma discharge that occurs in the reactor. The datas of supply voltage and current, as well as voltage and current discharge, was used to determine the average power during one period. From the simulation was obtained an increase in supply and discharge currents with increasing of frequency at the same operating voltage. Discharge power has increased in a specific voltage and increased frequency. It is obtained the average discharge power for 5.5 kV of 11.28 W and 10.90 W at a frequency of 21 kHz and 24 kHz, respectively. The highest efficiency obtained from the simulation that achieved at voltage of 1 kV and frequency of 45.7 kHz is equal to 56.59%.
Abstract: Nanotechnology is concerned with the materials and systems whose structures and components reveal novel and significantly improved physical, chemical, and biological properties, phenomena, and processes due to their micro size. Workforce development is needed to achieve the benefits of nanotechnology development along with technology transfer. The intensity should be on hands-on educational experiences by developing nano-tech laboratory demonstration experiments that could be adaptable and combined into existing courses in engineering and engineering technology. Theoretical heat transfer rates were calculated using existing relationships in the literature for conventional fluids and nano fluids. Experiments were conducted to determine the actual heat transfer rates under operational conditions using nanofluids and the heat transfer enhancement determined compared to fluids without nanoparticles.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Dispersion modeling of nitrous oxide emissions from a nitric acid plant in de...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Evaluation of 6 noded quareter point element for crack analysis by analytical...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Smart phone based robotic control for surveillance applicationseSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Design and implementation of an ancrchitecture of embedded web server for wir...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Load balancing in public cloud combining the concepts of data mining and netw...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Fault model analysis by parasitic extraction method for embedded srameSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
GENERATION OF POWER THROUGH HYDROGEN – OXYGEN FUEL CELLSinventy
Research Inventy : International Journal of Engineering and Science is published by the group of young academic and industrial researchers with 12 Issues per year. It is an online as well as print version open access journal that provides rapid publication (monthly) of articles in all areas of the subject such as: civil, mechanical, chemical, electronic and computer engineering as well as production and information technology. The Journal welcomes the submission of manuscripts that meet the general criteria of significance and scientific excellence. Papers will be published by rapid process within 20 days after acceptance and peer review process takes only 7 days. All articles published in Research Inventy will be peer-reviewed.
The heating pattern of the microwave dehydrator for treating petroleum crude ...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
The heating pattern of the microwave dehydrator for treating petroleum crude ...eSAT Journals
Abstract The effect of microwave dehydrator (modified domestic microwave oven) different types of petroleum oils were investigated in this paper, since microwave heats material selectively and volumetrically in relatively short time, and since its application in treating petroleum emulsion is tremendously recommended, thereof, it is the aim of this paper to investigate the microwave induced heating capacities of the individual components of the petroleum emulsion mixture. Three types of crude petroleum oils and water samples were put into test, from the result of this study, the temperature profile was observed to proceed as follow, at the first 20 seconds, all samples had similar temperature profiles in the range (50-60 ⁰C), however, beyond 20 seconds there was a clear distinct trend for every sample, in the interval from 20 seconds to 110 seconds, water sample had the curve with the highest temperature profile followed by UAE crude oil, then Saudi Arabia oil. Beyond 110 seconds, Kuwait crude oil had the maximum temperature profile continued sharply without reaching any plateau, followed by UAE then Saudi Arabia crude oil. The volumetric rate of heat generation also found to be in such a way that water sample had the maximum numerical value in the range (1-1.2 cal/s.cm3) at the beginning then decays as the heating time goes on, followed by that of Kuwait oil (0.8-1 cal/s.cm3), then Saudi Arabia crude oil (0.6-0.8 cal/s.cm3). Furthermore water also found to have the highest dielectric loss ranged between (7-8) and lowest wavelength in the range (1.5-2) followed by all the oil samples which had constant and identical dielectric properties in the range (0-0.5) and wavelength of 8 Cm. from the experimental results of this research, one can conclude that although both water and crude oils can interact effectively with microwave radiation yet the mechanism may not be the same since oils were shown to have very low dielectric loss. Another observation is different crude oils have different heating pattern, there this had to be into consideration when studying crude emulsion or refining. Keywords: microwave dehydrator, heating petroleum oils, dielectric of petroleum, and dielectric of water.
Removal of polluting gasses from the exhaust of combustion engines using mon ...Darren Magee
Magee assisted by Buchannan describes beautifully the process around the Archer reactor. A paper of such importance this describes for the first time cold fission / fusion in use to eliminate greenhouse gasses. This maps out the beginning of a new era in waste, water and sewage treatment accessing an undiscovered source of energy in the process
The International Journal of Engineering & Science is aimed at providing a platform for researchers, engineers, scientists, or educators to publish their original research results, to exchange new ideas, to disseminate information in innovative designs, engineering experiences and technological skills. It is also the Journal's objective to promote engineering and technology education. All papers submitted to the Journal will be blind peer-reviewed. Only original articles will be published.
The papers for publication in The International Journal of Engineering& Science are selected through rigorous peer reviews to ensure originality, timeliness, relevance, and readability.
The electrical profiles of the renewable polymer graphite (PG) composites upon ultra violet (UV) curing were investigated. Renewable PG films were prepared by mixing with varying weight percent of graphite (with an increment of 5 wt. % of prepared graphite) up to 30 wt.% and crosslinker. Then, the composites solution was slip casted and cured upon stimulated UV irradiation (UV accelerated weathering tester) at different time exposure (up to 1000 hours) was applied. Small changes on the functional groups of the composites were observed due to UV exposure time by Fourier Transform Infrared Spectroscopy (FTIR). Suggesting that chemical crosslink and chain scissions occurred within renewable polymer graphite composites. Further electrical profile through two point probe and four point probe method recorded visibly fluctuating values for both resistivity and conductivity within its composites range. Proposed here that the removal of organic contaminants and weak materials form both renewable polymer and graphite particles through the UV curing may have an effect on the formation of conductive network stability.
Tungsten oxide nanostructures for energy storage and field emission applicationseSAT Journals
Abstract
Single crystalline tungsten oxide (WO3) nanorods were synthesized over flexible carbon fabric via simple hydrothermal method
and used directly as supercapacitor (SC) electrode. WO3 nanorods with their peculiar structural features over the fabric exhibited
excellent electrochemical performance with a high specific capacitance of 481.34 F/g at scan speed 10 mV s-1. Additionally, these
nanorods showed propitious as electron field emitters where the registered turn on field and estimated field enhancement values
were 3.6 V/μm and 4550 respectively. These results indicate that present unique WO3 nanorods arrays over flexible carbon cloth
substrate are a promising candidate for constructing high-performance solid state electronics and electrochromic devices.
Key Words: Semiconductor compounds, Nanorods, carbon fabric, Supercapacitors, Field emitters and arrays
Determination of the hydrogen coefficient diffusion DH in the MmNi3.55Mn0.4Al...AI Publications
The hydrogen storage alloys MmNi3.55Mn0.4Al0.3Co0.75-xFex (0 ≤ x ≤0.75) were used as negative electrodes in the Ni-MH accumulators. The chronopotentiommetry and the cyclic voltammetry were applied to characterize the electrochemical properties of these alloys. The obtained results showed that the substitution of the cobalt atoms by iron atoms has a good effect on the life cycle of the electrode. The discharge capacity reaches its maximum in MmNi3.55Mn0.4Al0.3Co0.75-x Fex ( x = 0, 0.15, 0.35, 0.55 and 0.75) are, respectively, equal to 270, 266, 260, 210 and 200 mAh/g after 12 charge-discharge cycles. The diffusion behaviour of hydrogen in the negative electrodes made from these alloys was characterized by cyclic voltammetry after few activation cycles. The values of the hydrogen coefficient in MmNi3.55Mn0.4Al0.3Co0.75-x Fex ( x = 0, 0.15, 0.35, 0.55 and 0.75) are, respectively, equal to 5.86 10-10, 1.95 10-9, 3.44 10-9, 2.96 10-9 and 4.98 10-10 cm2 s-1. However, the values of the charge transfer coefficients are respectively equal to 0.35, 0.6, 0.5, 0.33 and 0.3. These results showed that the substitution of cobalt by iron decreases the reversibility and the kinetic of the electrochemical reaction in these alloys.
Impedance Spectroscopy Analysis of a Liquid Tin Anode Fuel Cell in Voltage Re...AEIJjournal2
A concept of a liquid tin anode-indirect carbon air fuel cell (LTA-ICFC) are described. Experimental
setups for analysis of LTA-ICFC polarisations of an operational electrochemical reactor of the LTA-ICFC
are presented. Results from Electrochemical Impedance Spectroscopy (EIS) Analysis of the electrochemical
reactor of the LTA-ICFC are shown and analysed.The rate-determining step of the system is concluded.
The charge-transfer resistance did not show considerable differences at 700-800 °C. This can be implied
that the charge-transfer resistance is not the rate-limiting step of the transport processes of the fuel cell.
The increase of the Warburg impedance concurrently with the resistance to fit mass-transport loss (R3)
suggests that the rate-limiting step for the LTA-ICFC in voltage recovery mode is the diffusion of the oxide
ions through SnO2 layer. The increment of mass transport lost, R3, of the cell causes the slowly increase of
the cell’s voltage over the voltage from 0.7-0.8 V at 700, 750, and 800 °C.
IMPEDANCE SPECTROSCOPY ANALYSIS OF A LIQUID TIN ANODE FUEL CELL IN VOLTAGE RE...AEIJjournal2
A concept of a liquid tin anode-indirect carbon air fuel cell (LTA-ICFC) are described. Experimental
setups for analysis of LTA-ICFC polarisations of an operational electrochemical reactor of the LTA-ICFC
are presented. Results from Electrochemical Impedance Spectroscopy (EIS) Analysis of the electrochemical
reactor of the LTA-ICFC are shown and analysed.The rate-determining step of the system is concluded.
The charge-transfer resistance did not show considerable differences at 700-800 °C. This can be implied
that the charge-transfer resistance is not the rate-limiting step of the transport processes of the fuel cell.
The increase of the Warburg impedance concurrently with the resistance to fit mass-transport loss (R3)
suggests that the rate-limiting step for the LTA-ICFC in voltage recovery mode is the diffusion of the oxide
ions through SnO2 layer. The increment of mass transport lost, R3, of the cell causes the slowly increase of
the cell’s voltage over the voltage from 0.7-0.8 V at 700, 750, and 800 °C.
Impedance Spectroscopy Analysis of a Liquid Tin Anode Fuel Cell in Voltage Re...AEIJjournal2
A concept of a liquid tin anode-indirect carbon air fuel cell (LTA-ICFC) are described. Experimental
setups for analysis of LTA-ICFC polarisations of an operational electrochemical reactor of the LTA-ICFC
are presented. Results from Electrochemical Impedance Spectroscopy (EIS) Analysis of the electrochemical
reactor of the LTA-ICFC are shown and analysed.The rate-determining step of the system is concluded.
The charge-transfer resistance did not show considerable differences at 700-800 °C. This can be implied
that the charge-transfer resistance is not the rate-limiting step of the transport processes of the fuel cell.
The increase of the Warburg impedance concurrently with the resistance to fit mass-transport loss (R3)
suggests that the rate-limiting step for the LTA-ICFC in voltage recovery mode is the diffusion of the oxide
ions through SnO2 layer. The increment of mass transport lost, R3, of the cell causes the slowly increase of
the cell’s voltage over the voltage from 0.7-0.8 V at 700, 750, and 800 °C.
Similar to Microwave dehydrator an environmental friendly step toward improving microwave demulsification of petroleum emulsions (20)
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
Explore the innovative world of trenchless pipe repair with our comprehensive guide, "The Benefits and Techniques of Trenchless Pipe Repair." This document delves into the modern methods of repairing underground pipes without the need for extensive excavation, highlighting the numerous advantages and the latest techniques used in the industry.
Learn about the cost savings, reduced environmental impact, and minimal disruption associated with trenchless technology. Discover detailed explanations of popular techniques such as pipe bursting, cured-in-place pipe (CIPP) lining, and directional drilling. Understand how these methods can be applied to various types of infrastructure, from residential plumbing to large-scale municipal systems.
Ideal for homeowners, contractors, engineers, and anyone interested in modern plumbing solutions, this guide provides valuable insights into why trenchless pipe repair is becoming the preferred choice for pipe rehabilitation. Stay informed about the latest advancements and best practices in the field.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
About
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Technical Specifications
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
Key Features
Indigenized remote control interface card suitable for MAFI system CCR equipment. Compatible for IDM8000 CCR. Backplane mounted serial and TCP/Ethernet communication module for CCR remote access. IDM 8000 CCR remote control on serial and TCP protocol.
• Remote control: Parallel or serial interface
• Compatible with MAFI CCR system
• Copatiable with IDM8000 CCR
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
Application
• Remote control: Parallel or serial interface.
• Compatible with MAFI CCR system.
• Compatible with IDM8000 CCR.
• Compatible with Backplane mount serial communication.
• Compatible with commercial and Defence aviation CCR system.
• Remote control system for accessing CCR and allied system over serial or TCP.
• Indigenized local Support/presence in India.
• Easy in configuration using DIP switches.
Microwave dehydrator an environmental friendly step toward improving microwave demulsification of petroleum emulsions
1. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 08 | Aug-2014, Available @ http://www.ijret.org 160
MICROWAVE DEHYDRATOR: AN ENVIRONMENTAL FRIENDLY STEP TOWARD IMPROVING MICROWAVE DEMULSIFICATION OF PETROLEUM EMULSIONS Souleyman A. Issaka1, Abdurahman H. Nour2, Rosli Mohd Yunus3, Azhari, H. Nour4 1Faculty of Chemical and Natural Resources Engineering, Universiti Malaysia Pahang 3Faculty of Chemical and Natural Resources Engineering, Universiti Malaysia Pahang 3Faculty of Chemical and Natural Resources Engineering, Universiti Malaysia Pahang 4Faculty of Industrial Science and Technology, Universiti Malaysia Pahang Abstract In this research introduces a newly improved method of microwave dehydrator. A system consists of modified domestic microwave oven and silicon based chemical demulsifiers was used to dehydrate two types of petroleum crude oils from Middle East. Silicone based additives which claimed to be nontoxic are used in conjunction with the modified microwave oven. The currently available demulsification techniques that consist mainly of chemicals together with mechanical, heating and electrical methods have some drawbacks, since chemicals are costly and harmful to the environment, mechanical techniques such as gravity settling tank, hydro cyclone vessel, centrifugal separators, and steam stripping are large requiring more space, time and cost, electrical techniques almost always work in a very high voltage that can easily cause fire via short circuit. Therefore, the objective of this project is to introduce the Microwave Dehydrator (MD) as a step forward to the commercialization of the microwave treatment of petroleum based emulsions. This is to replace or reduce the use of chemical dehydrators in the oil field. Simulated experimental model emulsions of various crude oils were produced to mimic the real emulsions. From previous articles, the optimal parameters to produce w/o emulsions of heavy crude oils were 0.25% (v/v) emulsifier’s concentration (Span 80) with mixing speed of 1600 rpm for 7 minutes mixing time. In this study, experimental stable emulsion were prepared from two different crude oils namely, Saudi Arabia (SA) and Kuwait, the water content in the emulsion was varied (20-80% and 50-50%), as well as the concentration of the additives (0.05 and 0.1%), results was discussed in terms of temperature, heat generation, and dielectric properties as well as water resolution. The results of the this research showed that, for 50-50% Kuwait oil emulsions, the optimal formulation was 0.1% additive and 2 minutes irradiation time gave the maximum water separation of 87%, while for 20-80% Kuwait oil emulsions, 0.1% additives and 2 minutes irradiation time had given the maximum separation of 52%. Furthermore, for Saudi Arabia crude emulsions, 50-50% w/o emulsions with 0.1% additive and 1.5 irradiation time had given the maximum separation of 85%. While for 20-80% w/o emulsions, 0.1% additive and 2 minutes irradiation time had given the maximum separation of 62%. Fundamentally the basic mechanism behind the effectiveness of microwave demulsification is that the electromagnetic wave that induce the water molecules to move as trying to rearrange themselves with the wave in two distinct mechanisms, known as ionic conduction and dipole rotation that would eventually convert the wave energy into heat generated within the water molecules. These results proved that microwave dehydrator can reduce the usage of chemical demulsifiers, as well as processing time and environmental issues. Keywords: Microwave dehydrator, Green demulsifiers, petroleum dehydration, petroleum emulsions, heavy crude oils, and Silicone demulsifiers
--------------------------------------------------------------------***---------------------------------------------------------------------- 1. INTRODUCTION Electromagnetic spectrum laying within 300MHz to 300GHz is known as microwave, which known to have electric and magnetic properties. When it is projected to materials, it obeys the optical rules of Transmission Absorption and reflection, depending upon the characteristics of the materials [17]. Hence the applied electromagnetic field will induce polarization effect to the medium.
The wave length varies from 1m to 1mm, in accordance with aforementioned frequencies (300MHz to 300GHz). Beside heating and scientific research purposes some other frequencies are reserved for specific purposes including these of cellular phone, radar and television satellite communications by American Federal Communication commission (FCC), however the most frequently used frequencies for Industrial, scientific and medical (ISM) purposes are 915 and 2450 MHz, [22].
Microwave is commonly preferred in material processing over its conventional counter part due to its volumetric heating. The mechanism of heat transfer in conventional heating is diffusion from the surface of the material then to the bulk, while in microwave heating, the temperature gradient in different location within the sample is almost
2. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 08 | Aug-2014, Available @ http://www.ijret.org 161
invariant, another important phenomenon is that different
material possess different heating pattern, and that due to the
variation in material’s microwave absorption capacity which
in turn depends on dielectric loss that depends on frequency
[22].
1.1 Equations of Heat Transfer in Microwave
The general form of heat transfer equation consists of three
principal forms which are conductive convective and
irradiation form given bellow.
1
273.15
273.15
4
4
dt
dT
C
T
T
V
A
T T
V
hA
q p
a
m
MW m a
Unless this is not the case in microwave heating, wherein
heat is generated within the material and its transfer property
is directly linked to the thermo-physical properties of
material as reported by Curet and others, thus the detailed
heat transfer mechanisms in microwaves will be explained
in the following set equations.
The rate heat generation in material is expressed as
ρcp
∂T
∂t
= div. k∇T + Q (2)
Where: 휌 and 푐푝 are density and heat capacity of sample
being heated,
휕푇
휕푡
rate of temperature increase and Q is the
internal energy acquired by the sample from the dissipated
microwave power and could be calculated for Z directed
electromagnetic wave by an equation relating power drop
from surface to bottom which is
Q
z =
F0
dp (z)
exp −
dz
dp z
z
0 (3)
퐹0: Microwave surface flux and dp is the penetration depth
which is strongly related to dielectric properties of the
sample designated as the distance at which the microwave
represents
1
푒
of the surface power flux and its mathematical
expression is:
dp =
c0
2πf
2ε 1 +
ε′′
ε
2
1
2
− 1
−
1
2
(4)
While surface flux at the same conditions as Maxwell
equations is calculated by the following relation.
F0 x, 0 =
2Psurf
ab
sin2
π x
a
(5)
Where (a, b) are the dimensions of the wave guide
However, from Maxwell equation’s perspective, the
magnitude of microwave power absorbed by the dielectric
samples can be estimated by the local electric field strength
on the sample being treated as
Qabs = ω. E2. ε′. ε′′ (6)
The electric field for plane wave propagation mode is solved
by the following equation
∇ × μr
−1 ∇E − ε r − j
σ
ω
ε0 k0 2
E = 0 (7)
휔 : Pulsation of microwave radiation (Rad/s)
E: electric field intensity (v/m)
ε : Complex permittivity
σ : electrical conductivity (s/m)
μr: relative electromagnetic permittivity of material (H/m)
K: thermal conductivity (w/m.K)
According to some previous researchers, in the above
equation the radiation and convective terms are very minor,
and that is because sample container has very low dielectric
constant therefore it does not generate much of heat and
hence most of the waves are transmitted through the glass
sample container to the emulsion. The density and heat
capacity of emulsion are calculated from the following
mixing rules:
1 (8) m w o
1 9 , , , p m p w p o C C C
Where:
m
, w o ,
(Kg/m3) Represent the densities of
emulsion, water and crude oil respectively, while
p m p w p o C C C , , , , ,
(kj/Kg.K) Represent the heat capacities of
emulsion, water and crude oil respectively.
1.2 Theory of Microwave Dehydration
Different materials have different heating capabilities by the
incident microwave energy. Hence for opaque materials, the
waves are totally reflected, while in transparent materials
they are transverse, but in dielectric materials, waves are
absorbed and transformed to heat. However, introducing
some specific metal powder to non conducting solvent
would render them microwave active and they can be heated
[18].
The treatment of crude oil emulsion is of major importance
in the respective industries, since most of the world crude oil
produced in the forms of emulsion. Water is normally a
good microwave absorber because of it high dielectric
properties, however in some rapports, at large samples the
heat transfer in oil was faster than that in the water and that
is imparted to the thickness of the oil, but this convention
does not work with small sample. Hence for small sample,
3. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 08 | Aug-2014, Available @ http://www.ijret.org 162
the heating rate of the water was faster [20]. Emulsion was
first treated via microwave by Wolf who was first started the
concept of microwave demulsification. Since then more and
more researches have been devoted paramount effort to this
field. The efficiency of microwave on emulsion was found
to induce some effect on the treated emulsion such as, the
increase in the temperature might leads to reduction in
viscosity, and this will increase the mobility of the water
droplet that will in turn neutralizes the zeta potential of the
dispersed droplet beside breaking the hydrogen bonding that
may exists between the water and the surfactant molecules.
Beside that the electromagnetic wave is believed to increase
the internal pressure of the water droplets leading to
reduction of the interfacial film thickness [21]. Most of the
aforementioned microwave affects depends on dielectric
properties, emulsion composition, droplet size distribution,
together with the operating conditions including temperature
and frequency. Sample is assumed homogeneous, the initial
temperature also assumed homogeneous, but thermo-physical
and dielectric properties are temperature dependent.
As reported earlier dielectric heating is a strong function of
pH, Viscosity, salt content, acid and water content [21].
Thus it is important to relate all of these parameters to assess
the microwave separation. With regard to separation
efficiency which can be estimated by sedimentations rate in
the case of water-in-oil emulsion, the settling velocity of
water droplets through oil is given calculated According to
the force balance and Stoke’s law as
(10)
18
) *
(
2
o
w o
w
g D
v
Where: D is the diameter of droplets. Similarly, if water is
the continuous phase, the rising velocity of oil droplets
through water is given by:
(11)
18
) *
(
2
w
w o
o
g D
v
The viscosities of oil and water ( o
and w
) are very
sensitive to temperature, in this regards, as temperature
increases, viscosity decreases much faster than the density
difference
( ) w o
does. Therefore, the heating either
by microwave or conventional, increases the velocity, o v
or w v
and consequently makes the separation of emulsion
faster.
Besides that, microwave also found to induce molecular
rotation of the polar droplets which may reduce or
neutralizes zeta potential of emulsion [23]. Zeta potential is
a layer of electrical charges suspends the droplets and
prevents their movement and coalescence. Since water
molecule is a polar, it rotates at a high frequency under
microwave irradiation. The molecular rotation raises the
temperature through friction, and also neutralizes the zeta
potential by disturbing the orderly arranged electrical
charges surrounding water droplets. Without the support of
zeta potential and interfacial barriers surrounding water
droplets are moved downward by gravitational force.
The advantage of applying microwave energy over the
conventional heating is its ability to heat sample more
uniformly than the conventional heating. Although in some
cases local overheating may occurs causing Hotspot or
thermal runaway within the sample, keeping in mind that
crude oil consists of vast numbers of component that differ
in their conductivity and polarity and ultimately in their
absorptive patterns with asphaltene being the dominant and
the major charge carrying component since it is the most
polar constituent of the crude oil, and contents significant
number of heteroatoms than the others constituent [19] [13].
Other researchers investigated the effects of system
geometry and water to oil ratios on emulsion stability, the
types of containers used in their experiment were non
reflective and partially reflective ceramic-metal complex
plates with emulsion being placed in the opened exposed
part, then from the data the maximum power distribution
(resonance R) is found by plotting the power calculated and
plotted for various parameters including dispersed phase
volume fraction, emulsion thickness and plate types. They
found the averages power absorption for o/w emulsion is
greater in sample heated with reflective surface and decrease
with increasing oil volume fraction. At the same time, the
thermal runaway was estimated by plotting the difference
between the maximum and minimum temperature of the
sample (o/w emulsion) plotted versus irradiation time was
found to increase with increasing dispersed phase volume
fraction [26]. Numerous investigations have been done in
the field of microwave heating and material processing,
Christian and friends have studied the absorption
mechanism for emulsion containing aqueous and nano
droplets, and found that Microwave absorption is attributed
to the types of ions, concentration as well as their
polarization [27]. Others have studied the effect of
microwave in treating industrial waste water emulsions and
admitted that microwave can be used as an alternative to the
existing demulsification methods, however addition of small
amount of acid was reported to increase the efficiency,
moreover the effect of aqueous phase composition on
microwave absorption was investigated elsewhere [21].
N.Bjerdalen and friends have applied the microwave and
ultrasonic techniques to treat the solid particles deposited at
the petroleum well, since these particles consist mainly of
asphaltene, resins and wax precipitated together with other
solid particles such as silica, bentonite and gypsum. The
parameters of concern were temperature, Viscosity, and
concentration of crude oil. The microwave device used was
Samsung Mini-Chef MW 1010c that had a frequency of 60
Hz and output power of 120 V, the temperature measuring
probe was of type Greenlee THH-500, while the ultrasonic
device was Medson mysono 201 A19001213 that had power
output of 15V and frequency of 3.5 MHz, the crude sample
4. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 08 | Aug-2014, Available @ http://www.ijret.org 163
was originated from SANTA BARBARA, the irradiation time for microwave was 80 and 180 seconds (s) for crude oil and asphaltene respectively, while for ultrasonic treatment it was varied as 30, 60, 180 s, results proved that microwave irradiation could elevate the temperature of petroleum crude oil and asphaltene and decrease the viscosity while with ultrasonic treatment the viscosity was observed to increase with increasing the irradiation time [11]. Abdurhaman and colleagues have compared the separation of water from crude oil by using conventional heating and microwave heating; the study was carried out on two different types of crude oils, and two different water to oil ratios of 30-70% and 50-50% w/o emulsions that were prepared by mixing the two phase vigorously via the standard three blade propeller at mixing speed of 1800 rpm at ambient temperature for 5 min, three types of emulsifiers namely Low sulfur wax residue (LSWR), Triton-x100 and Span 83 were used to produce the most stable w/o emulsion. For demulsification, Elba domestic microwave oven was used and the temperature profile of the sample was monitored using three thermocouples that were inserted in the sample at different location (Top, Middle and Bottom), microwave processing time was varied as 30, 60, 90, 120,150, 180,210 S, their results revealed the effectiveness of microwave heating over the conventional heating in breaking w/o emulsions [2]. Vladan Rajakovic and coworkers have used the combined Freeze/Thaw and microwave irradiation method to split the pure oil, from oil-in-water emulsion that was originated from metal working oil, the splitting process was carried out via the ultra-freezer device at three distinct temperature of - 20, -40 and -60 0C, for a processing or freezing duration of 10h, then thawed back in Air at 20 0C, after that placed in water bath at 40 0C or microwave at 95 0C (800w, 2450 MHz), however their results showed that the effectiveness of the freeze/thawing and microwave demulsification techniques depend mainly on the oil contain of the emulsion sample, freezing time and thawing steps, thawing time, indeed microwave also believed to induce molecules to acquire more energy because of super heating and increased reaction rate, and thus microwave demulsification is proved to be the most effective method in breaking emulsions [14]. A. H. Nour and coworkers have investigated the batch microwave oven with 2450 MHz in treating and breaking w/o emulsion, their experimental emulsion was prepared using commercially emulsifiers, the commercial emulsifiers used in their study were Triton-X100 and Low Sulfur Wax Residue (LSWR), their experimental emulsion was consisted of 20-80 and 50-50% water to oil ratio, the crude used was given by PETRONAS (Malaka refinery), the mixing power was provided through by the standard three blade propeller, the mixing speed was fixed at 1800 rpm, at ambient temperature for an emulsification time of 8 min, however their comprehensive study have proved that microwave can provide very fast and uniform heating and have a very strong potential to be used as an alternative demulsification technique for petroleum emulsion treatment [4].
Hyder A. Abdulbari and friends have studied the stability as well as microwave demulsification of petroleum emulsion; the stability was done by assessing the effectiveness of Sorbitan monooleate (Span 83), Triton-x100, Low sulfur wax residue (LSWR), and sodium dodecyl sulfate (SDDS), the parameters of interest were; the surfactant types, surfactants concentration, water volume fraction in the emulsion (10-90%), emulsification temperature and agitation speed, the raw crude petroleum oil were originated from Iran and Malaysian oil fields. Emulsions were prepared through the agent in oil method and mixture was agitated vigorously via the three blade propeller at emulsification speed of 1600 rpm at ambient temperature, the demulsification experiment was carried out using Elba microwave oven whose power output was 900 Watt and frequency of 2450 MHz. Their results also showed that microwave treatment gave rapid separation over the conventional gravitational settling [7]. Montserate Fortuny and colleagues have investigated the some important parameters for microwave demulsification, namely salinity, temperature, water content and pH. Their experimental emulsion was prepared by mixing the crude oil with saline water and homogenized using two steps emulsification techniques, thus in the first step the mixture was mixed by simple hand shaking, then certain amount of water was added in a drop-wise fashion while the mixing is going on, then in the second step the system was vigorously mixed using the ultra-turax T-25 homogenizer fitted with a S25- 25G dispersing tool, the water volume fraction was varied as (25, 35, 45) the mixing speed and time were fixed at 17500 for 10 min, the demulsification processes were performed using the commercial microwave with a processing time of 15 min. from their results it was observed that increasing the microwave power could increase the demulsification process, beside that high water contained emulsions were found to give high separation efficiency and that is because of the dielectric heating, also high salt content or high pH had reduced the demulsification rate, indeed the best separation rate was observed with emulsion having water volume fraction of 45% and pH of 7 [21]. Rosli M. yunus and colleagues have conducted a laboratory experiment to examine the performance of microwave heating technique in breaking water-in-crude oil emulsion in comparison with the conventional demulsification techniques. However, their results had concluded that microwave gave better separation than the conventional beside that microwave does not need any chemicals addition and could be used as an alternative green technique to treat petroleum emulsions [10]. A. N. Ilia Anisa and colleagues have also used the microwave demulsification techniques to treat w/o emulsions and optimize the operating conditions to fix the best operating conditions for microwave demulsification by using the RSM software [1] [15].
Lixin Xia and colleagues have studied the stability of crude oil emulsion and its relation to the presence of Asphaltene and resins (the natural surfactants), followed by microwave demulsification, their experimental emulsion was produced by using jet kerosene as oil phase mixed with certain
5. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 08 | Aug-2014, Available @ http://www.ijret.org 164
amounts of asphaltene and resin that was extracted from
Daqing crude oil (China), they varied the concentration of
asphaltene in the bulk emulsion in the range between 0.3 to
0.9 w/w%, and that of the resin was in the range of 1-4
w/w%, the mixing process was performed by simple hand
shaking. The demulsification process was carried out by
using either oil bath at 90 0C, or microwave oven or
microwave oven with power output of 850 watt and 2450
MHz, their results revealed that stability was strongly
depended on the amount of the asphaltene and resin in the
daqing crude oil, and that is because the adsorption of these
interfacial active components at the interfaces is believed to
form a mechanical film between the droplets, also
microwave demulsification had given better separation
result compared to the conventional demulsification
methods [8].
Abdurahman and colleagues have proposed a continuous
microwave demulsification method for water-in-crude oil
emulsion and found that the temperature rise within the
sample at given location was linear with respect to time and
the rate of temperature increase of emulsion decreases at
elevated temperature due to the decrease of dielectric loss of
water[3]. In this research, microwave oven was modified by
drilling a hole of 26 cm diameter at the top surface, and the
rounded bottom flask container was used to carry the
sample.
The chemical additives that used were chosen after massive
literature survey on the current commercial surfactants used
in the oil field.
With regard to the chemical additives, most of the
commercial additives contain long chain of polymers such
as aromatics, amines and sulfonic acid salts that are not very
safe from the environmental and economic prospective [24].
Dalmazzone had reported that silicone demulsifiers are
rather expensive but the current environmental issues may
render them useful in the future, because they are non-toxic
and non-harmful to the environment [5]. Therefore this
research is devoted to the introduction of new method which
combines the silicone demulsifiers with microwave, in order
to reduce the amount of silicone additives, which reflects the
reduction of cost. Microwave-silicone combination might
increase the efficiency, and decrease the environmental
worries.
2. MATERIALS AND METHOD
In this project, two different crude oils from different
geographical locations around the globe were donated by
Malaysian oil and gas company PETRONAS (Petroliam
National Berhad), a simulated experimental emulsions of
various crude oils were produced to mimic the real
emulsions. After massive screening, the optimal parameters
to produce stable w/o emulsions were 0.25% (v/v)
emulsifiers concentration (Span 80) with mixing speed of
1600 rpm for 7 minutes, emulsions was monitored for
stability within one week, then the composition of samples
that had retained their water without any separation within
the one week was taken as the optimal parameters to
produce stable emulsion. Commercial silicon based
demulsifiers were used without any further treatment. The
purpose of using demulsifiers was to investigate their
synergistic effect when they are used in conjunction with
microwave, indeed the silicone based chemical demulsifiers
are green and claimed not harmful to the environment.
Domestic microwave oven was used with little modification
as depicted in the diagram (Figure 1).
Fig 1: Microwave Dehydrator (MD)
Figure 1 is a schematic representation of the apparatus used
to carry out this experimental research, 1) sample holder
(Round bottom flask) inside the microwave oven, 2)
thermocouple for measuring temperature, 3) hose to move
the sample (emulsion) in and out, 4) peristaltic pump, 5)
sample tank, 6) Pico data Logger for temperature
monitoring.
The system consists of domestic microwave oven, with
maximum power output of 800watt, and 2450 MHz
frequencies, in this study, the operation frequencies were set
at 800 watt, a container of 250 ml round bottomed flask was
used. A thermocouple was used to record the temperature
through a Pico data logger connected to computer. After the
fresh emulsion was prepared, silicon demulsifiers were
added to the sample in different dosage of 0.1 and 0.05%
prior to it is irradiation.
2.1 Equations used for Data Interpretation
Equation (1) was be used to calculate the heat generation of
the treated samples, after the convective and radiation terms
are eliminated it lead to equation (12).
12
( )
m P,m
m MW m
C
q
dt
dT
Equation 12 is used to calculate the volume rate of heat
generation. The physical properties such as density ( m
)
and the heat capacity ( P m C , ) of the emulsion can be
calculated from the mixing rules as in equations (8) and (9).
The temperature data are collected using the Picodata Loger
device.
6. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 08 | Aug-2014, Available @ http://www.ijret.org 165
The dielectric constant and dielectric loss of water was
calculated by empirical correlations given by wolf [30].
' 85.215 0.33583 13
' r w T
r'w
'' 320.658
1.0268 T (14)
Where
' : Dielectric constant of water
'' : Dielectric loss of water
Van Hippel proposed equation for dielectric properties of
various petroleum oils, in this regard dielectric constant of
crude oil for this study were calculated using equation
(15)[29].
' 2.24 0.000727 (15)
' r o T
2.2 Measurement of Penetration Depth and
Wavelength
Gallawa reported that, there is a direct relationship between
the frequency and the wavelength. There is also a
relationship between the frequency and the degree or speed
of heating, as well as the depth of penetration within the
sample. The wavelength (which is the distance between
positive peaks or negative peaks of two adjacent waves) is
equal to the speed of light divided by the frequency. For
practical purposes, the speed of light does not change.
Therefore, the only two variables in equation are the
frequency and the wavelength, their relationship as follows:
(16)
f
c
m
Where: m
(m) is wavelength, c (ms-1) is speed of light,
and
f
is frequency (Hz).
The above relation indicates, the higher the frequency, the
shorter the wavelength, and vice versa (low frequency,
corresponds to longer wavelength) [6]. Tanmay related the
microwave penetration depth p D
and wavelength of
radiation in the medium m
to dielectric constant r
' and
dielectric loss (loss factor) r
'' via the relation given in
equations (19), (20).
(19)
2 * * 1 1
1/ 2
2
'
''
'
r
r
r
p
f
c
D
And
(20)
1 1
2
1/ 2
2
'
''
'
r
r
r
m
f
c
The two most common techniques for dielectric properties
measurements are the resonant cavity, or cavity perturbation
method, and the transmission and reflection method [28].
3. RESULTS AND DISCUSSIONS
Samples of water-in-oil emulsions were prepared with
different ratio as described in methodology. In this study the
microwave power level was fixed at the maximum of 800
watt, the irradiation time was recorded from zero to 3.5
minutes, the variables investigated were, types of crude oils
used in this study and the water volume fractions (50-50 and
20-80%), as well as the concentration of the silicone
demulsifiers.
3.1 The Temperature Profiles of Water-in-Crude
Oil Emulsions
The experimental results of the current research would be
given in the following sections. This current section is
concerned about calculating and discussing the temperature
profiles as well as electromagnetic parameters including
dielectric properties, heat generation, and penetration depth,
for water-in-crude emulsions of different crude oils.
Fig 2: Temperature profiles of 50-50% w/o emulsions
containing 0.1and 0.05% demulsifiers at 800 watt and
microwave irradiation time of 210 seconds.
7. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 08 | Aug-2014, Available @ http://www.ijret.org 166
Fig 3: Temperature profiles of 20-80% w/o emulsions containing 0.1 and 0.05% demulsifiers at 800 watt and microwave irradiation time of 210 seconds. Figures 2 and 3 reveal the data of the temperature profiles obtained in this study for two different crude oils that are originally from Middle East. Figure 2 represent high water cut of 50-50% w/o emulsion and Figure 3 represent the low water cut of 20-80% w/o emulsions. As mentioned in the scope of this study, certain other specific parameters such as oil types, and demulsifiers’ concentration on the temperature profile of the emulsions at fixed irradiation time would be discussed particularly on each figure. This is to gain some ideas on how and at what temperature the sample is being heated, indeed these experimental values of the temperature profiles would be used latter on in the modeling of system to determine the volumetric heat generation of each system as well as the wave characteristics on the sample including dielectric properties. Based on Figure 2, at the beginning of the microwave irradiation, all emulsions had the same values of temperature which is to somehow close to the ambient temperature. But it rose very rapidly to around 50 °C in just 20 seconds, and then within the period from 20 seconds to 50 seconds each component had taken different trend. Thus the curve of the 0.1% demulsified Kuwait oil emulsion and that of the 0.05% demulsified Saudi Arabia crude oil emulsion have had almost similar trends in such a way that their gradual temperature increase as function of irradiation time had almost similar numerical values, within this period (20-50 seconds). Hence the temperature increment is ranged from around 35 to more or less 100 °C for within 20 and 50 seconds respectively. Furthermore; 0.05% demulsified Kuwait oil sample’s trend have had even greater temperature values of around 140 °C, then 0.1% demulsified Saudi Arabia crude oil emulsion had the trend with the lowest temperature figure 2. Then starting from 50 second until the end of the irradiation time, the trends were just opposite to what they were at 50 seconds. Generally all curves reached plateaus at various temperature maximum, but the difference was not that big for all samples. The maximum temperature of the 50-50% w/o emulsions was found to be more or less 130 °C.
In more details, for 50-50% w/o emulsions, 0.1% demulsified Kuwait and Saudi Arabia oils had equal and highest temperature curve of around 150 °C, then followed by 0.05% demulsified Saudi Arabian crude oil having plateau at around 145 °C, then finally 0.05% demulsified Kuwait oil which had its temperature plateau at around 140 °C. As said earlier the difference is not that big but it could be said that heating is enhanced with the increased demulsifiers (0.1). On the other hand Figure 3 represents the temperature profile of 20-80% w/o emulsions, it is clear from the figure that water cut does to somehow effects the heating process, however the general trends of temperature profile were more or less similar for the two different water cuts and all samples were heated almost in the same fashion, the only strange observation is that at 50-50% w/o emulsion, the 0.05% demulsified Kuwait oil emulsion samples had the highest temperature at the beginning and lower temperature at the end. Basically, the 0.1% demulsified Kuwait oil emulsion sample had the lowest temperature at the beginning and high temperature at the end. But for 20-80% w/o emulsions, the sample of 0.1% demulsified Saudi Arabian oil, had the maximum temperature at the beginning and minimum temperature at the end (Figures 2 and 3), but the conclusion is that the effect of demulsifiers in rising the temperature or improve the heating was observed at low water cut, in another word demulsifiers work better at low water cut. 3.2 Rate of Temperature Increase in Emulsions
Fig 4: Rate of temperature increase vs. irradiation time for 50-50% w/o emulsions containing 0.1 and 0.05% demulsifiers at 800 watt for 210 seconds.
8. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 08 | Aug-2014, Available @ http://www.ijret.org 167
Fig 5: Rate of temperature increase vs. irradiation time for 20-80% w/o emulsions containing 0.1 and 0.05% demulsifiers at 800 watt, for 210aeconds. Figures 4 and 5 reveal the rate of temperature increase for 50-50% and 20-80% w/o emulsions respectively. With regard to the curves in Figure 4, almost all samples seemed to have similar trends, (increase at the beginning to some maximum values then decrease back to some plateaus), the detailed discussion of the temperature rate fluctuation with irradiation time for figure 4 could be explained by segmenting the course of the curves into three distinct regions according to their behaviors. Region one is designated at the time interval from 0 to 20 seconds, in this interval the temperature rate was almost in linear increment with time, but 0.05% demulsified Kuwait oil had somehow slow increment value than the others at the beginning, then increased rapidly to the same levels as others as heating goes on. Region two lies within the time interval starting from 20 to 60 seconds. In this interval, the temperature rate had experienced an increase for some samples and decrease for others, however the critical values were observed in the forms of either concave or convex that happened at 35 sec, where 0.05% demulsified Kuwait oil had the maximum values of 2.4 (°C /s), then followed by that of 0.1% demulsified Kuwait oil which was 1.8 (°C/s), unfortunately the temperature rate for Saudi Arabia oil emulsions were observed to decrease with temperature in this second interval, hence the minimum values were found to be 1.5 and 1.2 (°C/s), for 0.1 and 0.05% demulsified Saudi Arabia crude oils respectively.
Region three is the interval that starts from 60 seconds to the end, where all of the curves reach certain steady state values with Saudi Arabia crude oil having the highest values. Indeed Figure 5 represents the heating rate for 20-80% w/o emulsions. Generally, the heating rate was much higher than it was for 50-50% w/o emulsion. And also the highest temperature rate was observed in the very first 10 seconds, and it was 7.3 (°C /s), for 0.05% demulsified Kuwait oil samples, this is the sample with the highest temperature rate, in contrast 0.05% demulsified Saudi Arabia emulsion was found to possess the lowest heating rate of 4 (°C /s), this may be due to crude oil composition. Then 0.1% demulsified Kuwait and Saudi Arabia crude oils were found to have intermediate heating rates of 6.8 and 5.8 (°C /s), respectively.
3.3 Rate of Heat Generation in Emulsions
Fig 6: Volumetric rate of heat generation vs. time for 50- 50% w/o emulsions containing 0.1 and 0.05% demulsifiers at 800 watt for 3.5 minutes.
Fig 7: Volumetric rate of heat generation vs. irradiation time for 20-80% w/o emulsions containing 0.1 and 0.05% demulsifiers at 800 watt for 3.5 minutes.
The values of the volumetric rate of heat generation in figure 6 and 7 were calculated from equation 12, wherein the density and heat capacity of the mixture were determined by equations (8) and (9) respectively. Since microwave heat materials volumetrically and uniformly without temperature gradient, also the system is assumed well mixed therefore, the heat distribution within the mixture component is assumed uniform, and thus there is no temperature gradient or conductive heat transfer within the mixture components, and also the conductive term is dropped because the sample container is transparent to electromagnetic wave, and hence it generate no heat, and therefore the temperature rate was the main and varying parameter in calculating the volume rate of heat generation, and that was evidenced by the curves that had an identical
9. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 08 | Aug-2014, Available @ http://www.ijret.org 168
trends as that of the temperature rates, the only difference is their numerical values which were a bit smaller reader may refer to figures (4, 5, 6, and 7) to check this fact. Generally the heating rate as well as heat generation of 50- 50% w/o emulsion (higher water cut emulsions) was brought about by the influence of the water molecules, or dipole rotation while the heating rate and heat generation profiles of the 20-80% w/o (low water cut emulsion) were found to have lower temperature rate profile compared to the higher water cut (50-50%), these samples was dominated by the ion mobility and ion concentrations, and heat is expected to be generated from the friction resulted when the rapid and random movement of ions is opposed by the viscous bulk fluid. 3.4 Dielectric Constant vs. Temperature of Water- in-Crude Oil Emulsions Dielectric constant is defined as the ability of material to accommodate or obstruct microwave energy as it passes through. Is regarded as the single mechanism through which the polar and conducting material could interact with microwave that lead to the energy generation within the materials.
Fig 8: Dielectric constant Vs. Temperature for 50-50% w/o emulsions at 800 W.
Fig 9: Dielectric constant Vs. Temperature for 20-80% w/o emulsions 800 W.
Figures 8 and 9 contain the calculated results of the dielectric constant for 50-50 and 20-80% w/o emulsions respectively. For 50-50% w/o emulsion all samples had similar curves, that is all started at one point which located between 35-40 (values of dielectric constant) then decreased gradually in a fluctuating pathways until they all reached a constant values of 23 (dielectric constant) more or less. When temperature reached (130 °C), however the real steady plateau was achieved at temperature of 162 °C , where 0.05% demulsified 50-50% Kuwait oil emulsion had the maximum dielectric constant values of 22) then followed the Saudi Arabian sample of the same composition having dielectric constant of 20. The rest two 0.1% demulsified Kuwait and Saudi Arabia samples had identical dielectric constant values of 18 in that particular interval. With regard to 20-80% w/o emulsion, the curves of all samples were found to start at almost similar values more or less 15 then immediately started to decrease, each curve was taking distinct path with 0.1% demulsified Kuwait oil having the path with the highest values of dielectric constant followed by 0.1% demulsified Saudi Arabia, and 0.05% demulsified Kuwait then 0.05% demulsified Saudi Arabia, but all paths were converged at a plateau that is seemed to have very close values of more or less 11 when temperature reached 150 °C. In comparing the two curves one can conclude the following; the dielectric constant of the 50- 50% w/o emulsion was higher than the dielectric constant of the 20-80% w/o emulsion and this again will consolidate the domination of the water molecules, also in 50-50% samples, low demulsifiers’ concentration gave high values of dielectric constant and the opposite was observed with the 20-80% w/o emulsions (Figures 8, 9). 3.5 Dielectric Loss Vs. Temperature of Water- Crude Oil Emulsions Dielectric loss or loss factor is a term given to the ability of conductive and polar materials to dissipate or accommodate the electromagnetic wave that is obstructed by the action of the dielectric constant, and thus help material to convert more energy in the forms of heat, and its characterized to decrease with increasing temperature as would be seen in the graphs (Figure (10, 11).
Fig 10: Dielectric Loss vs. Temperature for 50-50% w/o emulsions
10. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 08 | Aug-2014, Available @ http://www.ijret.org 169
Fig 11: Dielectric constant vs. Temperature for 20-80% w/o emulsions (800 W, 3.5 min) Figures 10 and11 represent the values of the dielectric loss of various samples of 50-50 and 20-80% w/o emulsions that are demulsified by various concentrations of silicone demulsifier that is used as the only demulsifier in this research. Particularly; Figure 10 represents the dielectric loss of 50-50% w/o emulsions of two crude oils, however; from first glance one can realize that not all the wave absorbed by the sample are converted to energy. This fact could be seen if one compares the values of the dielectric constant and dielectric loss of the 50-50% w/o emulsions or Figures 8 and 10, it is clear that the maximum values of the absorbed wave (Dielectric constant) was within the interval of (35-40) (Figure 8), but the maximum value of the portion that is converted to heat (dielectric loss) was within the interval of (4-5) (Figure 10), this is almost ten time reduction in the values of absorbed electromagnetic wave, that may be due the small sized sample used in this experiments. The other observation is that the dielectric loss curves was shown to decrease sharply and reached its minimum value very fast when the sample temperature is 90 0C, this is in contradiction to the dielectric constant curves whose reduction was slow and gradual, in summary it can said that dielectric constant and Loss have certain proportionality but not directly, hence more waves are dissipated but only very few are converted to energy, and this applies on the 20-80% sample as well. With regard to dielectric loss of 20-80% w/o emulsions, it is clear from figure 11 that all systems had almost identical values lies in the interval between (0.8-1) except 0.05% demulsified Saudi Arabia oil emulsion which have had the value of (1.6) almost double of the others, then as temperature increase, the profiles of the dielectric loss (Figure 11) had decreased gradually till they reached a constant values of (0.4).
3.6 Wave Length vs. Temperature of Water-in- Crude Oil Emulsions
Fig 12: Wave length Vs. Temperature for 50-50% w/o emulsions (300W)
Fig 13: Wave length Vs. Temperature for 20-80% w/o emulsions (800W, 3.5 min) Figures 12 and 13 reveal the wavelength of the microwave on 50-50 and 20-80% w/o emulsions respectively, this is very important to know since shorter wave length would result in faster and efficient heating, indeed the wavelength also reported to vary with temperature, in fact these claims were evidenced clearly on the current result, as given in Figure 12, which showed the wavelength on samples of 50- 50% w/o emulsions as function of sample temperature. Generally; all samples showed very similar profiles of the wavelength as a function of temperature the initial wavelength for all samples was almost identical and located around 2 cm at 36 °C, and final value was 3 cm more or less, hence the effect of oil types as well as demulsifiers’ concentration was very minor for 50-50% w/o emulsions.
With regard to 20-80% w/o emulsions, the values of the wavelength were to somehow greater than that of 50-50%, but within 20-80% samples, all samples appeared to have similar wavelength. the initial value was around 3 cm and final value of around 4 cm, from this results it could be said that the amount of water in the emulsion does effect much the wavelength and that may affect the heating pattern as well, since energy generation is proportional to the
11. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 08 | Aug-2014, Available @ http://www.ijret.org 170
wavelength, however this research showed that, higher water content emulsion (50-50%), could reduce the wave length to as low as 2 cm, while it was as low as 3 cm on (20- 80%) emulsions, hence water in sample have an obvious effect on reducing the wavelength of the incident microwave radiation. 3.7 Penetration Depth vs. Temperature of Water- Crude Oil Emulsions
Fig 14: Penetration depth vs. Temperature for 50-50% w/o emulsions (800W) Figures 14 and 15 describe the penetration depth of the electromagnetic waves on the samples of 50-50% and 20- 80% w/o emulsions respectively. The penetration depth for 50-50% w/o emulsions was found to be almost equal for all compositions, and varies with temperature. Its starting value was 5 cm for all samples at the very beginning of the irradiation when the temperature was just 36 °C, then it increased slowly until it reached a constant value of 15 cm when temperature was 102 °C,
Fig 15: Penetration depth Vs. Temperature for 20-80% w/o emulsions (800 W)
however comparing this result to that of 20-80% w/o emulsions of Figure 15; it is clear that water cuts does greatly affect the penetration depth, hence the difference was around two order of magnitude greater for 20-80%, whose initial value was around 15 cm for the three samples and it was around 10 cm for 0.05% demulsified 20-80% Saudi Arabia (S.A) crude oil at 66 °C, then increased gradually with temperature, indeed all values were converged at plateau of around 30 cm, when temperature reached 143 °C. From this observation it can be said that the actual concentration of demulsifiers does not affect much the penetration depth nor the oil type only water cut does, another information is that the penetration depth was found to increase with increasing temperature and that is to somehow in accordance with the theory which defines penetration depth as the depth where the power is reduced to 37% of the surface values, indeed Davinder have reported the gradual dependence of penetration depth on sample temperature (Davinder et al., 1997). 4. MICROWAVE DEHYDRATION OF PETROLEUM BASED EMULSIONS The preceding section had discussed the demulsification process in terms of thermal properties but this section would tackle the efficiency of microwave in breaking several types of emulsions, including experimental as well as real emulsions, and the microwave performance would be assessed in terms of water resolution. 5. EFFECTS OF DEMULSIFIERS’ CONCENTRATION AND IRRADIATION TIME ON DEHYDRATION This section is aimed to investigate the synergistic effect of the chemical assisted microwave demulsification in terms of water separation from the stable emulsion, together with the irradiation time for 50-50 and 20-80% w/o emulsions of Kuwait and Saudi Arabia. 5.1 Kuwait Oil The effect of microwave in breaking w/o emulsions was assessed in this section, in terms percentage of water resolved from the emulsions.
Fig 16: Percentage of water separation for 50-50% w/o emulsion (Kuwait oil)
0
2
4
6
8
10
12
14
16
18
20
36
56
74
97
99
100
102
110
116
122
128
134
139
144
159
165
164
165
163
158
156
Penetration depth (cm)
Temperature (°C)
0.1%, Kuwait oil
0.05%, Kuwait oil
0.1%, S.A. oil
0.05%,S. A. oil
0
5
10
15
20
25
30
35
66
123
127
127
125
143
149
153
161
163
169
Penetration depth (cm)
Temperature (°C)
0.1%, Kuwait oil
0.05%, Kuwait oil
0.1%, S. A. oil
0.05%, S. A. oil
12. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 08 | Aug-2014, Available @ http://www.ijret.org 171
Figure 16 reveals the experimental results obtained from 50- 50% w/o emulsions of Kuwait crude oil, as stated earlier many parameters are to be discussed in this paragraph but currently Figure 16 is particularly devoted to observe the synergistic effects of the demulsifers’ concentration and Irradiation or processing time on the emulsion separation efficiency, which in turn evaluated by pouring the processed samples in measuring cylinder and the separated amount of water is read of as settled layer at the bottom of the cylinder for duration of 1 hour (settling time). Indeed two different concentrations of demulsifiers (0.1% and 0.05%), and three different irradiation times (1.5, 2 and 3.5 minutes) were investigated on 50-50% w/o emulsion. However; the results showed that a composition with 0.1% v/v concentration of demulsifiers and 2 minutes of irradiation time had given the best separation efficiency of almost 87%. Then followed by sample 0.1% demulsifiers and 3.5 minutes irradiation which had a separation efficiency of around 75%, on the other hand 0.05% demulsifiers concentration and 1.5 microwave exposure time were found to be non effective for 50-50% w/o emulsions (Figure 16).
Fig 17: Percentage of water separation for 20-80% w/o emulsion (Kuwait oil) Figure 17 was plotted to investigate the effect of water volume fraction on the emulsions, since it is well known that systems with different composition will respond differently to incident electromagnetic wave, therefore system of 20- 80% w/o emulsion composed of 0.05% demulsifiers and 3.5 minute irradiation time have had the maximum water separation yield 52% more or less water resolution followed by 0.1%, 3.5 minutes which had water resolution of around 37%. Other interesting observation in here is that, low demulsifiers concentration had given much higher yield which was around 52% and 35% for 0.05% and 0.1% demulsified emulsions respectively, hence from this result for low water content Kuwait oil of 20-80% w/o emulsions, low demulsifiers’ concentration and long irradiation time would give a better yield, so the conclusion is that the quantitative values of the parameters used to demulsify 50- 50% and 20-80% w/o emulsions are just opposite to one another.
5.1 Saudi Arabia Oil (S.A.)
Fig 18: percentage of water separation for 50-50% w/o emulsion (Saudi Arabia oil) Figure 18 represents the experimental results of 50-50% w/o of Saudi Arabia (S.A.) crude oil emulsions, all parameters are fixed as same as they were in Kuwait oil emulsions, so this can help to observe the effects by considering oil types as independent parameter. From these results, it was observed that the profile is almost same as it was with Kuwait oil, in a sense that high demulsifiers concentration and short irradiation time would give high yield. From figure 18, it was observed that three samples had the highest values namely sample of 0.1% emulsifiers and 1.5 minutes irradiation had separation efficiency of around 85%, but the same samples again had 82% separation efficiency when the irradiation time had increased to 2 minute; in fact this result sound ambiguous and could be attributed to the thermal properties of the samples. The other sample with high separation yield was composed of 0.05% demulsifiers’ concentration and 3.5 minutes irradiated sample which had around 59% of its water separated.
Fig 19: percentage of water separation for 20-80% w/o emulsion (Saudi Arabia oil)
13. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 08 | Aug-2014, Available @ http://www.ijret.org 172
Figure 19 represents the separation efficiency for 20-80% w/o emulsions of S.A. crude oil produced using the same parameters as 50-50% emulsion, only the water content is varied purposely to observe its effect on the separation efficiency. This time the effect was in same fashion as 50- 50% w/o emulsions, hence in this types of (S.A) crude oil; the water volume fraction does not affect much on the separation efficiency but demulsifiers’ concentration and irradiation time do effect, hence the maximum separation efficiency of 62% was observed in sample having 0.1% demulsifiers that is irradiated for 2 minute. Indeed when the same sample irradiated further to 3.5 minutes; the separation efficiency had reduced to around 58%, furthermore it was also observed in this 20-80% w/o (S.A.) crude oil that, low concentration of demulsifiers did not give much effect; this is in reverse of the 20-80% Kuwait oil in which low demulsifiers concentration and high irradiation time gave better yield (Figure 17). 6. CONCLUSIONS A microwave dehydrator method was developed to treat petroleum based emulsions from crude oils that are originated from Middle East (Saudi Arabia and Kuwait). In this system, green chemical additive was used in conjunction with microwave; the advantage of this method is that the usage of chemicals are very much reduced to as low as 0.1%. In this study, experimental stable emulsion were prepared from two different crude oils (Saudi Arabia and Kuwait). The water content in the emulsion was varied (20-80% and 50-50%), as well as the concentration of the additives (0.05 and 0.1%), results was discussed in terms of, temperature, heat generation, and dielectric properties as well as water resolution. The results of the this research showed that, for 50-50% Kuwait oil emulsions, the optimal formulation was 0.1% additive and 2 minutes irradiation time, which gave the maximum water separation 0f 87%. While for 20-80% Kuwait oil emulsions, 0.1% additives and 2 minutes irradiation time had given the maximum separation of 52%. Furthermore, for Saudi Arabia crude emulsions, 50-50% w/o emulsions with 0.1% additive and 1.5 irradiation time had given the maximum separation of 85%. While for 20-80% w/o emulsions with 0.1% additive and 2 minutes irradiation time had given the maximum separation of 62%. The outcome of this investigation is that this newly improved method which combines the silicone based demulsifiers with microwave can consolidate the effort made by researchers to the betterment of petroleum dehydration technology, since it can reduce the amount of silicone additives, which reflects the reduction of cost. Microwave-silicone combination might increase the efficiency, and decrease the environmental worries and cost.
REFERENCES
[1]. A. N. Ilia Anisa, Abdurahman H. Nour and Azhari H. Nour, 2011, Destabilization of heavy and light crude oil emulsions via Microwave heating Technology: An optimization study, J. of Applied Science 11 (16): 2898- 2906 [2]. Abdurahman H. Nour and Rosli M. Yunus 2006, A continuous microwave heating of water-in-crude oil emulsions: An experimental study, J. of Applied science, 6 (8): 1868-1872, 2006 [3]. Abdurahman H. Nour and Rosli M.yunus 2006, A comparative study on emulsion demulsification by microwave radiation and conventional heating, J. of Applied science 6(10): 2307-2311. [4]. Abdurahman. H. Nour et al.,2010, Demulsification of water-in-oil emulsions by microwave heating technology, World academy of science, engineering and technology, Vol: 38-02-27. [5]. C. Dalmazzone et al., 2005, Mechanism of crude oil- interface destabilization by silicone demulsifiers. SPE International symposium on oilfield chemistry SPE 80241 [6]. Gallawa, J.C. (1989). The Complete Microwave Oven Service, Handbook: Operation, maintenance, Troubleshooting and Repair. Library of Congress Cataloging in Publication Data [7]. Hayder A. Abdulbari, N. H. Abdurahman, Y. M. Rosli, Wafaa K. Mahmood and H. N. Azhari 2011, Demulsification of petroleum emulsions using microwave separation method, International Journal of the Physical Sciences Vol. 6(23), pp. 5376-5382, 9 October. [8]. Lixin Xia, Shiwei Lu, and Guoying Cao 2004, Stability and demulsification of emulsions stabilized by asphaltenes or resins, J. of Colloid and Interface Science 271 504–506 [9]. Montserrat Fortuny et al., 2007, Effects of salinity, temperature, water content and pH osn the Microwave demulsification of crude oil emulsions, J. of Energy and Fuels 21 1358-1364. [10]. Rosli, M.Yunus and Abdurahman, H. Nour 2005,water-in-oil demulsification via microwave irradiation, Proceedings of the International Conference on Recent Advances in Mechanical & Materials Engineering 30-31 May 2005, Kuala Lumpur, Malaysia Paper No.51 [11]. N. Bjorendalen et al., 2004, the effect of microwave and ultrasonic irradiation on crude oil during production with a horizontal well, J. of petroleum science and engineering 43 139– 150 [12]. Abdurahman H. Nour et al, 2012, demulsification of water-in-crude oil (w/o) emulsion via microwave irradiation: An optimization, J. of scientific research and essays, Vol. 7 (2), PP. 231-243. [13]. Sujoy Kumar Samanta, Tanmay Basak, Bhaskar Sengupta 2008, Theoretical analysis on microwave heating of oil–water emulsions supported on ceramic, metallic or composite plates, International Journal of Heat and Mass Transfer 51- 6136–6156 [14]. Vladana Rajakovic, Dejan Skala 2006, Separation of water-in-oil emulsions by freeze/thaw method and microwave radiation, J. of Separation and Purification Technology 49 (2006) 192–196
14. IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 08 | Aug-2014, Available @ http://www.ijret.org 173
[15]. Abdurahman H. Nour, A. N. Ilia Anisa1 and Azhari H. Nour 2012, Demulsification of water-in-oil (W/O) emulsion via microwave irradiation: An optimization, J. of Scientific Research and Essays Vol. 7(2), pp. 231-243, 16 January. [16]. Fang, C.S., and Lai, P.M.C. (1995). Microwave Heating and Separation of Water-in-Oil Emulsions, J. Microwave Power and electromagnetic energy. 30, 46-57. [17]. Roger Meredith 1998, Engineer’s Hand Book of industrial Microwave heating, the institution of electrical engineers, London, United Kingdom. [18]. Camelia et al 1998 Dielectric parameters relevant to microwave dielectric heating, J.of Chemical Society Reviews, 1998, volume 27 [19]. Helene et al., 2009, Dielectric properties of crude oil components, j. Of Energy Fuels 2009, 23, 5596–5602: DOI: 10.1021/ef900445n. [20]. Barringer et al., 1994 Effect of sample size on the microwave heating rate : oil vs. water, AIChE journal ISSN 0001-1541 CODEN AICEAC, 1994, vol. 40, no9, pp. 1433-1439 [21]. Montserrate et al., 2006, Effect of Salinity, Temperature, Water Content, and pH on the Microwave Demulsification of Crude Oil Emulsions, J. of Energy & Fuels 2007, 21, 1358-1364 [22]. Thostenson and Chou, 1999, Microwave processing: fundamentals and applications. J. of composite PII: S1359- 835X (99)00020-2 [23]. Fang, C.S., Chang, B.K.L., and Lai, P.M.C. (1988). Microwave Demulsification. Chem. Eng.Comm. 73: 227- 233. [24]. Austen K. Flatt, 2011, Siloxane cross-linked demulsifiers, United state pattent, US 7, 981, 979 B2. [25]. Davinder Kaur et al., 1997, Microwave penetration depth measurements of ag-yba2cu307-6 thin films, J of Solid State Communications, Vol. 106, No. 4. Pp.23 I-234. [26]. Sujoy Kumar samanta, Tanmay basak, 2009, J. of Food research international, 12, 1337-1350. [27]. Christian holtze et al. 2006, The Microwave absorption of emulsion containing aqueous micro and nano droplets: A mean to optimize microwave heating, J. of colloid and interface science 302, 651-657. [28]. Tanmay, B. (2004). Role of Resonances on Microwave Heating of Oil-Water Emulsions. AIChE.J. [29]. Von Hippel, A.R. (1954). Dielectric Materials and Applications. MIT Press. Cambridge, MA. [30]. Wolf, N.O. (1986). Use of Microwave radiation in Separating Emulsions and Dispersion of Hydrocarbon and water. U.S.Patent 4,582.629