2. Lot Management( 一 )
Hold
將 Lot 的狀態改為 Hold 。
Lot 可在 WIP 的任何時間點 (Wait 、 Run) 被
Hold 。
在不同的時間點作 Hold 時, Hold 的紀錄會不同
,如 HOLD (Wait Hold) 、 RHLD (Running Hold)
等。
大多數的 WIP 功能皆不能被執行。
可選對單一批 Lot 作 Hold ,或是選擇對一整個
Part 所有的 Lot 作 Hold 。
Hold 時,一定要紀錄 Hold User 、 Hold Time 、
Hold Code 與 Hold Comment 。
對同一個 Lot ,可作多次的 Hold ,但其 Hold
3. Lot Management( 二 )
Release
解除 Lot 的 Hold 狀態。
若一批 Lot 有多個 Hold Code ,則需要全部解除
後,才能進行 WIP 功能。
全部的 Hold Code 都解除後, Lot 的狀態需回復
到被 Hold 時的原本狀態。因此 MES 必須要能記
得此 Lot 的原始狀態。
Release 時,必須紀錄 Release User 、 Release
Time 、 Release Code 、 Release Comment 。
可依照條件 (Lot ID 、 Product 、 Main
Plan 、 Sub Plan 、 Step 等 ) 一次選擇多批 Lot 或
是同一批 Lot 的不同 Hold Code 來做 Release 。
4. Lot Management( 三 )
Lot Future Hold
預定一批 Lot 在抵達 " 未來 " 某個站點時,要由
系統將 Lot 作 Hold 。
Future Hold 有兩個時間點 (Hold Type) ,一個是
從上一個 Step 作 Step Out 到此 Step 時 (Queue
Hold) ;一個是從此 Step 作 Step Out 時 (Step Out
Hold) 。
對於一個 Future Hold 設定,可設為 Once 或是
Repeat , Once 只會 Hold 一次, Repeat 則一直
有作用。
Future Hold 中,使用者定義 Lot ID 、 Hold
Type 、 Once/Repeat 和 Hold Comment 。
因 Future Hold 所產生的 Hold ,其 Hold User 是
系統, Hold Code 是內定的如 System Hold 。
5. Lot Management( 四 )
Cancel Lot Future Hold
解除 Lot Future Hold 的設定。
可由 Lot ID 、 Hold Type 、 Once/Repeat 、 Hold
User 等作篩選條件,來選出 Lot Future Hold 的項
目。
刪除 Future Hold 之後,對已被 Hold 的 Lot 沒有
影響,未被 Hold 的 Lot 就不會被 Hold 住。
6. Lot Management( 五 )
Product Future Hold
設定屬於特定 Product 的所有 Lot ,當 WIP 到特
定 Step 時,將會被 Hold 。
同一個 Product 可設多個 Step 作 Future Hold ,同
一個 Step 只能有一個 Future Hold 。
Product Future Hold 的 Hold Type 可為 Queue
Hold 或是 Step Out Hold 。
Hold Comment 由使用者輸入, Hold
Code 、 Hold User 與 Hold Time 皆由系統決定。
Cancel Product Future Hold
解除 Product Future Hold 的設定
7. Lot Management( 六 )
Split
將 Lot 做的其中幾片分出去,形成另一批或數批
Lot 。原來的 Lot 為 Parent Lot ,新增加的 Lot 為
Child Lot 。
Parent Lot 與 Child Lot 的數量,最少必須還有一
片。
Split Type 有暫時性與永久性兩種,暫時性的分
批,代表在未來的某一個 Step 要作 Merge ,因
此會有 Future Hold 與 Future Merge 這兩個設定
。
剛分批完的 Child Lot ,除了 Qty 明顯不同外,
其 Production 設定和 Parent Lot 完全相同。
8. Lot Management( 七 )
Cancel Future Merge
取消由暫時性分批,所產生的 Future Merge 動作
。
可全部取消同一族譜中所有 Lot 的 Future
Merge ,或是單獨取消任一批 Lot 的 Future
Merge 。
若取消 A Lot 的 Future Merge 後,只留下一批 B
Lot 將和 A Lot 作 Future Merge 的設定,則也要
同時將 B Lot 的 Future Merge 刪除。
Future Merge 會同時包含一個 Future Hold (Merge
Hold) 的設定, Cancel Future Merge 時,也同時
將此 Merge Hold 刪除。
9. Lot Management( 八 )
Merge
將兩個或以上的 Lot 合併成一批。
作合併的 Lots ,其 Production 設定須完全相同,
即從 Production ID (Name + Version) 到 Step ID 都
要相同才可作 Merge 。
可進行 Merge 的 Lot ,不限是否屬於同一族譜的
Lot ,只要符合上述條件即可。
Merge 時,選擇一個 Lot 為 Parent Lot ,此 Parent
Lot 會被留下來,其他的 Lot 為 Child Lot ,在合
併後,會變成 Terminal 狀態。
Merge 後 Parent Lot 的 Qty 為所有 Merge Lot 的
Qty 總和,不過不能超出每批 Lot 的 Max
Count 。
10. Lot Management( 九 )
Terminate
終止一批 Lot 的運作,將其狀態改為 TERM ,除
了 UnTerminate 與 View Lot Info 外,其他任何
WIP 與 Lot Management 功能皆無法作用於
TERM Lot 。
必須輸入 Comment 。
UnTerminate
回復 TERM Lot 成原來的狀態。
若是因為 Merge 而導致 Qty 變成 0 的 Lot ,無法
用此功能回復。
11. Lot Management( 十 )
Scrap
報廢一批 Lot 中的幾片晶圓或玻璃基板,以便
WIP 時,機台不會再處理到這幾片。
使用者可選 Component Count 和 Component ID 來
標示要 Scrap 的元件,這些被 Scrap 的元件,其
狀態就改成 SCRAP 。
若一批 Lot 全部皆 Scrap ,除了 Component 外,
Lot 的狀態也要改成 SCRAP 。
UnScrap
回復已 Scrap 的 Component 或 Lot 成原來的狀態
。
必須輸入 Comment 。
12. Lot Management( 十一 )
Skip
將一批 Lot 往未加工的站點方向,搬移到所選定
的 Step 。
唯有狀態為 WAIT 的 Lot 可執行此功能。
移動到一個新站點之後,此 Lot 必須進行和 Step
Out 後,取得站點資訊相同的功能,如將 Step 等
Production 資訊記錄到 Lot 中,取得此站的 PPID
與 Reticle 等。
若新到的站點有 Future Action (Future
Hold 、 Future Merge 等 ) ,則也必須執行這些
Future Action 。
Skip 過的站點若有 Future Action ,則允許跳過,
以顯示訊息方式通知操作者資訊。
13. Lot Management( 十二 )
Back
將一批 Lot 往已加工的站點方向,搬移到所選定
的 Step 。
唯有狀態為 WAIT 或 FINL 的 Lot 可執行此功能
。
移動到一個新站點之後,此 Lot 必須進行和 Step
Out 後,取得站點資訊相同的功能,如將 Step 等
Production 資訊記錄到 Lot 中,取得此站的 PPID
與 Reticle 等。
若新到的站點有 Future Action (Future
Hold 、 Future Merge 等 ) ,則也必須執行這些
Future Action 。
Back 過的站點若有 Future Action ,則允許跳過
,以顯示訊息方式通知操作者資訊。
15. Lot Management( 十四 )
New Product
對特定 Lot 進行產品換線的動作。
唯有狀態為 WAIT 的 Lot 可執行此功能。
使用者可選擇一個全新的 Product ID 、 Main Plan
ID 、 Sub Plan ID 與 Step ID ,將目前已經加工的
材料,轉換成另外一種完全不同的產品。
使用者也可選擇原來的 Product Name 、 Main
Plan Name 、 Sub Plan Name 與 Step Name ,但是
Version 不同,以便將目前的 Lot ,立即移到新的
版本設定上 ( 與版本控制功能作比較 ) 。
16. Lot Management( 十五 )
Bonus
動態手動增加 Lot 的 Component 數目。
Bonus 後, Lot 的數量不能超過 Max Count 。
View Lot Information
看查 Lot 的資訊。
可以 Area ID 、 Location ID 、 EQP Type 、 EQP
ID 、 Product Name 、 Lot Status 、 Lot ID 等作為
篩選和選擇條件。
列出 Lot 的所有資訊。