Intrinsic Safety Explained
•
4 likes•3,724 views
An Intrinsically Safe Barrier is a device which limits the power (energy) which can be delivered from a safe area into a hazardous zone. Explosions are prevented; not just contained in explosion-proof conduit and housings. Not only is electrical energy (voltage and current) held within safe limits, but total energy is also contained, eliminating the possibility of an explosion due to excessive heat. Use of barriers and a total intrinsically safe design philosophy offers considerable advantages from cost and safety standpoints.
Report
Share
Report
Share
Download to read offline
Recommended
Intrinsic Safety
This document summarizes a presentation on intrinsic safety and hazardous areas. It begins with an overview of the presenter's micro-course series on practical electrical engineering topics. The presentation then covers the fundamentals of explosion protection, including defining intrinsic safety, area classification systems, gas properties, temperature classifications, and methods of explosion protection. Intrinsic safety (Ex i) is explained in detail as a method to prevent ignition in hazardous areas by limiting the energy and voltage in electrical circuits. Circuit diagrams demonstrate how intrinsic safety barriers work to isolate hazardous and safe areas.
Electrical maintenance in Hazardous area
This document discusses electrical maintenance in hazardous areas. It defines area classification and explains why it is important to prevent electrical hazards from causing fires and explosions. It outlines the fire explosion triangle and important terminology like hazard, hazardous atmosphere, ignition temperature, and flammable substances. It then describes the concentration limits for explosions and different area classification systems from NEC and IEC codes. The document provides examples of zone classifications and discusses gas groups, temperature classes, ingress protection, types of protections, and materials of construction for electrical equipment in hazardous areas. It also covers labeling requirements and dos and don'ts for working in hazardous areas.
Basics of atex
The document provides an overview of ATEX regulations for explosive atmospheres. It discusses:
1) The basics of ATEX classification including area classes, explosion groups, and risk management principles.
2) A comparison of IEC and EN standards for explosive atmospheres, covering regulations for area classification, equipment requirements, and installation standards.
3) Common principles of explosion prevention including the combustion triangle of flammable material, oxygen, and ignition sources, as well as potential ignition sources.
14-Hazardous Area Classification.ppt
This document discusses hazardous area classification. It defines a hazardous area as one where flammable gases, vapors or dusts may be present. It describes international standards for classifying hazardous areas, including dividing them into zones based on the likelihood of a flammable substance being present, and groups based on the substance's autoignition temperature. It also compares the IEC and NEC classification systems, outlining their approaches to zones/divisions, temperature ratings, protection techniques, and ingress protection ratings. The document provides information on these topics to explain the need for proper hazardous area classification.
Fire protection systems
The document discusses fire protection systems for aircraft. It describes the four classes of fires based on the type of fuel (A-D) and appropriate extinguishing agents for each class. It also outlines various fire detection systems, including thermo-switch, thermocouple, Fenwal, and pneumatic systems. Fire extinguishing agents work by displacing oxygen or chemically combining with oxygen to prevent combustion. Common agents are carbon dioxide, freon, halon 1301, and nitrogen. Fire extinguishing systems can be conventional or high rate discharge, with the latter utilizing compressed gases or liquids under high pressure.
Hazardous area classification and Elecrtical, Instrument and Process Engineer...
This presentation explains the Hazardous gas Classification and area Classification, and the responsibility of Electrical, Instrument and Process Engineer Responsibility.
Sil presentation
The document discusses functional safety and fire and gas (F&G) systems. It defines functional safety and outlines standards like IEC 61508. F&G systems aim to detect and respond to hazards to reduce risk. Key components discussed include detectors, logic solvers, and final elements. Specific final elements presented are Niagara monitors for delivering water, electric actuators for redundancy, and VDD deluge valves with a fully redundant design. These components are described and their advantages for achieving safety integrity levels are outlined.
Areas clasificadas iec_nec
The document provides information on hazardous area classification standards and compares the International Electrotechnical Commission (IEC) Zone system to the National Electric Code (NEC) Class/Division system. It defines IEC Zones 0, 1, and 2 and examples of how different areas would be classified. Protection techniques like flameproof, increased safety, and intrinsic safety used in both systems are also discussed. Charts are included that compare gas groups, temperature classifications, equipment standards, and protection methods between the IEC and NEC/Canadian Electric Code systems.
Recommended
Intrinsic Safety
This document summarizes a presentation on intrinsic safety and hazardous areas. It begins with an overview of the presenter's micro-course series on practical electrical engineering topics. The presentation then covers the fundamentals of explosion protection, including defining intrinsic safety, area classification systems, gas properties, temperature classifications, and methods of explosion protection. Intrinsic safety (Ex i) is explained in detail as a method to prevent ignition in hazardous areas by limiting the energy and voltage in electrical circuits. Circuit diagrams demonstrate how intrinsic safety barriers work to isolate hazardous and safe areas.
Electrical maintenance in Hazardous area
This document discusses electrical maintenance in hazardous areas. It defines area classification and explains why it is important to prevent electrical hazards from causing fires and explosions. It outlines the fire explosion triangle and important terminology like hazard, hazardous atmosphere, ignition temperature, and flammable substances. It then describes the concentration limits for explosions and different area classification systems from NEC and IEC codes. The document provides examples of zone classifications and discusses gas groups, temperature classes, ingress protection, types of protections, and materials of construction for electrical equipment in hazardous areas. It also covers labeling requirements and dos and don'ts for working in hazardous areas.
Basics of atex
The document provides an overview of ATEX regulations for explosive atmospheres. It discusses:
1) The basics of ATEX classification including area classes, explosion groups, and risk management principles.
2) A comparison of IEC and EN standards for explosive atmospheres, covering regulations for area classification, equipment requirements, and installation standards.
3) Common principles of explosion prevention including the combustion triangle of flammable material, oxygen, and ignition sources, as well as potential ignition sources.
14-Hazardous Area Classification.ppt
This document discusses hazardous area classification. It defines a hazardous area as one where flammable gases, vapors or dusts may be present. It describes international standards for classifying hazardous areas, including dividing them into zones based on the likelihood of a flammable substance being present, and groups based on the substance's autoignition temperature. It also compares the IEC and NEC classification systems, outlining their approaches to zones/divisions, temperature ratings, protection techniques, and ingress protection ratings. The document provides information on these topics to explain the need for proper hazardous area classification.
Fire protection systems
The document discusses fire protection systems for aircraft. It describes the four classes of fires based on the type of fuel (A-D) and appropriate extinguishing agents for each class. It also outlines various fire detection systems, including thermo-switch, thermocouple, Fenwal, and pneumatic systems. Fire extinguishing agents work by displacing oxygen or chemically combining with oxygen to prevent combustion. Common agents are carbon dioxide, freon, halon 1301, and nitrogen. Fire extinguishing systems can be conventional or high rate discharge, with the latter utilizing compressed gases or liquids under high pressure.
Hazardous area classification and Elecrtical, Instrument and Process Engineer...
This presentation explains the Hazardous gas Classification and area Classification, and the responsibility of Electrical, Instrument and Process Engineer Responsibility.
Sil presentation
The document discusses functional safety and fire and gas (F&G) systems. It defines functional safety and outlines standards like IEC 61508. F&G systems aim to detect and respond to hazards to reduce risk. Key components discussed include detectors, logic solvers, and final elements. Specific final elements presented are Niagara monitors for delivering water, electric actuators for redundancy, and VDD deluge valves with a fully redundant design. These components are described and their advantages for achieving safety integrity levels are outlined.
Areas clasificadas iec_nec
The document provides information on hazardous area classification standards and compares the International Electrotechnical Commission (IEC) Zone system to the National Electric Code (NEC) Class/Division system. It defines IEC Zones 0, 1, and 2 and examples of how different areas would be classified. Protection techniques like flameproof, increased safety, and intrinsic safety used in both systems are also discussed. Charts are included that compare gas groups, temperature classifications, equipment standards, and protection methods between the IEC and NEC/Canadian Electric Code systems.
Water Mist Systems - Akshay Jangam.
The revolutionary Water-Mist technology. Low Pressure & High Pressure Water-Mist. Design calculations, Standards, Applications, Limitations. Alternative to Gas suppression - sprinkler systems.
Contact: 95949-66462
Hazardous area module- Zones, Method of Determination of Hazardous area Radiu...
The explosion properties of our fuel like gasses, vapors, combustible dusts have been studied and organized by their flammability limits and ignition temp etc in order to suitably assess the potential of an explosion and to take appropriate preventative measures to avoid an explosion.
Hazardous Area Location Guide - IEC NEC CEC & ATEX By Emerson Industrial
Hazardous Area Location Guide - IEC NEC CEC & ATEX By Emerson IndustrialThorne & Derrick International
This document provides information on IEC protection techniques for hazardous areas and areas with combustible dust, including definitions of IEC zones and IP ratings. It also includes charts comparing IEC and NEC area classifications, zone definitions, and guidelines for using equipment certified for different standards.Explosion Protection
This document provides an overview of explosion protection. It begins by defining the basics of explosion protection, including the three factors required for an explosion - flammable material, oxygen, and an ignition source. It also discusses explosion limits and classifications. The document then outlines the key principles of explosion protection, including preventing explosive atmospheres, avoiding ignition of atmospheres, and mitigating explosion effects. It provides details on statutory regulations and standards for explosion protection worldwide, in the European Union, North America, and Russia. The remainder of the document covers technical principles such as zone classification and equipment protection levels.
Hazardous Area Classification
This document provides definitions and information related to fire and explosion hazards. It defines key terms like hazard, risk, fire, explosion, ignition sources, and stages of combustion. It also discusses flash point, fire point, auto-ignition temperature, and flammability limits. The document outlines how to prevent and mitigate explosions through ventilation, ignition source control, containment, material substitution, and separation. It also discusses hazardous area classification and electrical equipment certification for different zones and gas/vapor groups.
Explosion protection theory and practice
This document provides an overview of explosion protection principles and guidelines. It discusses the risks of explosions from combustible gases, vapors, and dusts. It also summarizes the key standards and directives around explosion protection from Europe (ATEX), North America (NEC/CEC), and international standards. The document outlines explosion protection concepts like classification of hazardous areas, protection types, and conformity assessment procedures.
Hazardous area
The document discusses hazardous areas and explosion protection. It defines a hazardous area as an area containing an explosive gas or air mixture. It explains the concepts of the fire triangle, area classification, minimum ignition current, and protection methods. The key points are:
- Hazardous areas are classified based on the likelihood and duration of an explosive atmosphere occurring. They are divided into Zones 0, 1, and 2.
- Electrical equipment used in hazardous areas must be certified for the specific gas, temperature class, and zone to prevent explosions from occurring.
- Factors like gas properties, ventilation, and probability of a release are considered in the area classification process to select the proper electrical equipment.
Safety system
The document discusses safety systems used in industrial plants, including emergency shutdown systems (ESD), process shutdown systems (PSD), and fire and gas control systems (F&G). It defines these terms and describes their objectives, typical components, and functions. Safety is measured by factors like average probability of failure on demand (PFDavg) and risk reduction factor (RRF). The document also covers related topics like hazard analysis, risk, reliability, availability, and definitions of key safety terminology.
Fm 200 schematic
The fire suppression system consists of a detection system with smoke detectors that trigger an alarm if two detectors are activated. This leads to a timer that discharges gas from cylinders if the fire is not put out within a minute. The extinguishing system includes cylinders of FM200 gas that ruptures via a solenoid valve and fills the area through piping and nozzles to extinguish the fire. Once the fire is out, the area simply needs ventilation for the FM200 gas to dissipate, allowing production to resume quickly after cleaning and checks.
Hazardous area classification
There are two major standards for hazardous area classification: the North American standard and the European standard. The North American standard classifies areas by class, division, and group based on the type of flammable material present and how often a flammable atmosphere occurs. The European standard uses zones instead of divisions and has some differences in gas groupings. Both standards aim to safely classify hazardous areas to prevent ignition of flammable atmospheres.
OISD-STD-117 Fire Protection Facilities for Petroleum Depots, Terminals, Pipe...
The document outlines standards for fire protection facilities at petroleum depots, terminals, and pipeline installations in India. It discusses requirements for fire water systems, foam systems, control room protection, firefighting equipment, alarm systems, and organization of fire safety resources. The standards aim to minimize loss of life and property from fire through rapid containment and extinguishment. Requirements include fixed water spray and foam systems for large storage tanks, monitors and hydrants in hazardous areas, and clean agent systems for control rooms.
Electronic Warfare: War Cases Studies
(1) In 1967, tensions between Israel and its Arab neighbors escalated when Egypt closed the Strait of Tiran, blockading Israeli shipping. (2) On June 5th, Israel launched a surprise air attack, destroying nearly the entire Egyptian Air Force on the ground through sequential strikes on airfields. (3) By the end of the first day, the Egyptian, Jordanian, and Syrian air forces had suffered heavy losses, with Israel claiming to have destroyed around 300 aircraft while only losing 19 of its own.
Hazardous area classification and control of ignition sources
This document discusses hazardous area classification and control of ignition sources. It defines hazardous areas as any place where an explosive atmosphere may occur, and outlines the process to classify these areas into zones based on the likelihood and duration of an explosive atmosphere. The document provides guidance on identifying potential ignition sources and selecting appropriate equipment for use in the classified zones to ensure safety. It emphasizes the need to control ignition sources through design measures, work procedures, and proper equipment selection according to the zone classification.
Clean agents fire suppression system- fm200, novec 1230 and ecaro 25
FM200 is a waterless fire suppression system that extinguishes fires quickly within 10 seconds by removing elements from the fire triangle without reducing oxygen levels. It requires less agent than other systems, extinguishes fires before significant damage, and has minimal environmental impact. ECARO-25 is also effective on electronics and requires 20% less agent than FM200 or HFC-227. It can replace Halon 1301 systems due to its compatible properties. Novec 1230 manufactured by 3M is another Halon replacement that does not deplete ozone and has low global warming potential, making it suitable for sensitive areas where water damage should be avoided.
Hazardous Area Classification
This document discusses hazardous area classification. It defines hazardous areas as areas where flammable gases or vapors may be present. Areas are classified into zones based on the likelihood and duration of an explosive atmosphere occurring. Zone 0 areas have explosive atmospheres present continuously, Zone 1 areas have them likely to occur occasionally, and Zone 2 areas are not likely but possible for short periods. Selection of electrical equipment depends on the area classification and gas properties. Standards provide guidelines for equipment certification to ensure safe operation in hazardous environments.
Tank protection
This document discusses various methods for applying foam to storage tanks for fire protection, including fixed surface systems, seal area protection, and subsurface foam injection. It provides design guidelines for each method, such as minimum application rates and durations. It also describes Williams' foam chambers and foam makers that can be used for fixed surface application through discharge outlets. The foam chambers are available in custom sizes and flows, and can accommodate dual agents. Supplementary application in diked areas is also addressed.
Torpedo
1. A torpedo is a self-propelled underwater weapon used to destroy ships. It consists of a propulsion system, guidance system, and explosive warhead.
2. Torpedoes can be guided by wires or wireless radio signals. The most common propulsion systems are electric motors or Otto fuel engines, since jets require oxygen.
3. India's newest torpedo is the Varunastra, which has a high explosive warhead, electric engine, and wire guidance system for attacking submarines up to 40 km away.
Fm 200
FM200 is a colourless gas which is liquified under pressure for storage. Like Halon 1301 it has a low toxicity level and is superpressurised with Nitrogen to 24.8bar (360psi). It rapidly extinguishes most commonly found fires through a combination of chemical and physical mechanisms.
fire & gas detection system
This document discusses fire and gas detection systems. It begins by defining fire and gases, explaining that fire is a chain reaction between fuel and oxygen that produces heat, light and other byproducts. Gases disperse and mix rapidly. Detection systems are needed to monitor hazardous gas levels and provide early warning before hazards form. They protect people, infrastructure and the environment per safety laws and codes. Detection considers flammable, toxic and asphyxiant gas risks. The document then covers gas properties, ignition risks, limits of flammability, and detection technology types like infrared and catalytic sensors. It stresses the importance of instrument calibration and certification to ensure accurate measurements. Examples of industrial accidents caused by gas leaks are also provided.
LPG – Liquefied Petroleum Gas & Gas Detection System
This document provides information about LPG (liquefied petroleum gas) and gas detection systems. It discusses what LPG is, how it is used to supply buildings and various appliances, and the components of LPG and gas detection systems including piping, outlets, sensors, panels, and standards. The document also outlines procedures for installing, testing, commissioning, maintaining and operating LPG and gas detection systems. Calculations for LPG demand, storage, and pipe sizing are presented.
Intrinsic safety and flameproof apparatus in mines
mine environment engineering
Intrinsic safety and flameproof apparatus in mines
research and development on explosions in mines
prevention of explosion in mines
Lunch And Learn Presentation
This document provides an overview of R.Stahl Inc., which offers explosion protected products for hazardous locations. The agenda covers explosion protection methods, barriers and isolators, remote I/O, HMIs, and system solutions. Details are then given on R.Stahl's electrical, lighting, and automation products, as well as their system capabilities and sources of additional information. Basics of intrinsic safety and nonincendive protection are also summarized.
More Related Content
What's hot
Water Mist Systems - Akshay Jangam.
The revolutionary Water-Mist technology. Low Pressure & High Pressure Water-Mist. Design calculations, Standards, Applications, Limitations. Alternative to Gas suppression - sprinkler systems.
Contact: 95949-66462
Hazardous area module- Zones, Method of Determination of Hazardous area Radiu...
The explosion properties of our fuel like gasses, vapors, combustible dusts have been studied and organized by their flammability limits and ignition temp etc in order to suitably assess the potential of an explosion and to take appropriate preventative measures to avoid an explosion.
Hazardous Area Location Guide - IEC NEC CEC & ATEX By Emerson Industrial
Hazardous Area Location Guide - IEC NEC CEC & ATEX By Emerson IndustrialThorne & Derrick International
This document provides information on IEC protection techniques for hazardous areas and areas with combustible dust, including definitions of IEC zones and IP ratings. It also includes charts comparing IEC and NEC area classifications, zone definitions, and guidelines for using equipment certified for different standards.Explosion Protection
This document provides an overview of explosion protection. It begins by defining the basics of explosion protection, including the three factors required for an explosion - flammable material, oxygen, and an ignition source. It also discusses explosion limits and classifications. The document then outlines the key principles of explosion protection, including preventing explosive atmospheres, avoiding ignition of atmospheres, and mitigating explosion effects. It provides details on statutory regulations and standards for explosion protection worldwide, in the European Union, North America, and Russia. The remainder of the document covers technical principles such as zone classification and equipment protection levels.
Hazardous Area Classification
This document provides definitions and information related to fire and explosion hazards. It defines key terms like hazard, risk, fire, explosion, ignition sources, and stages of combustion. It also discusses flash point, fire point, auto-ignition temperature, and flammability limits. The document outlines how to prevent and mitigate explosions through ventilation, ignition source control, containment, material substitution, and separation. It also discusses hazardous area classification and electrical equipment certification for different zones and gas/vapor groups.
Explosion protection theory and practice
This document provides an overview of explosion protection principles and guidelines. It discusses the risks of explosions from combustible gases, vapors, and dusts. It also summarizes the key standards and directives around explosion protection from Europe (ATEX), North America (NEC/CEC), and international standards. The document outlines explosion protection concepts like classification of hazardous areas, protection types, and conformity assessment procedures.
Hazardous area
The document discusses hazardous areas and explosion protection. It defines a hazardous area as an area containing an explosive gas or air mixture. It explains the concepts of the fire triangle, area classification, minimum ignition current, and protection methods. The key points are:
- Hazardous areas are classified based on the likelihood and duration of an explosive atmosphere occurring. They are divided into Zones 0, 1, and 2.
- Electrical equipment used in hazardous areas must be certified for the specific gas, temperature class, and zone to prevent explosions from occurring.
- Factors like gas properties, ventilation, and probability of a release are considered in the area classification process to select the proper electrical equipment.
Safety system
The document discusses safety systems used in industrial plants, including emergency shutdown systems (ESD), process shutdown systems (PSD), and fire and gas control systems (F&G). It defines these terms and describes their objectives, typical components, and functions. Safety is measured by factors like average probability of failure on demand (PFDavg) and risk reduction factor (RRF). The document also covers related topics like hazard analysis, risk, reliability, availability, and definitions of key safety terminology.
Fm 200 schematic
The fire suppression system consists of a detection system with smoke detectors that trigger an alarm if two detectors are activated. This leads to a timer that discharges gas from cylinders if the fire is not put out within a minute. The extinguishing system includes cylinders of FM200 gas that ruptures via a solenoid valve and fills the area through piping and nozzles to extinguish the fire. Once the fire is out, the area simply needs ventilation for the FM200 gas to dissipate, allowing production to resume quickly after cleaning and checks.
Hazardous area classification
There are two major standards for hazardous area classification: the North American standard and the European standard. The North American standard classifies areas by class, division, and group based on the type of flammable material present and how often a flammable atmosphere occurs. The European standard uses zones instead of divisions and has some differences in gas groupings. Both standards aim to safely classify hazardous areas to prevent ignition of flammable atmospheres.
OISD-STD-117 Fire Protection Facilities for Petroleum Depots, Terminals, Pipe...
The document outlines standards for fire protection facilities at petroleum depots, terminals, and pipeline installations in India. It discusses requirements for fire water systems, foam systems, control room protection, firefighting equipment, alarm systems, and organization of fire safety resources. The standards aim to minimize loss of life and property from fire through rapid containment and extinguishment. Requirements include fixed water spray and foam systems for large storage tanks, monitors and hydrants in hazardous areas, and clean agent systems for control rooms.
Electronic Warfare: War Cases Studies
(1) In 1967, tensions between Israel and its Arab neighbors escalated when Egypt closed the Strait of Tiran, blockading Israeli shipping. (2) On June 5th, Israel launched a surprise air attack, destroying nearly the entire Egyptian Air Force on the ground through sequential strikes on airfields. (3) By the end of the first day, the Egyptian, Jordanian, and Syrian air forces had suffered heavy losses, with Israel claiming to have destroyed around 300 aircraft while only losing 19 of its own.
Hazardous area classification and control of ignition sources
This document discusses hazardous area classification and control of ignition sources. It defines hazardous areas as any place where an explosive atmosphere may occur, and outlines the process to classify these areas into zones based on the likelihood and duration of an explosive atmosphere. The document provides guidance on identifying potential ignition sources and selecting appropriate equipment for use in the classified zones to ensure safety. It emphasizes the need to control ignition sources through design measures, work procedures, and proper equipment selection according to the zone classification.
Clean agents fire suppression system- fm200, novec 1230 and ecaro 25
FM200 is a waterless fire suppression system that extinguishes fires quickly within 10 seconds by removing elements from the fire triangle without reducing oxygen levels. It requires less agent than other systems, extinguishes fires before significant damage, and has minimal environmental impact. ECARO-25 is also effective on electronics and requires 20% less agent than FM200 or HFC-227. It can replace Halon 1301 systems due to its compatible properties. Novec 1230 manufactured by 3M is another Halon replacement that does not deplete ozone and has low global warming potential, making it suitable for sensitive areas where water damage should be avoided.
Hazardous Area Classification
This document discusses hazardous area classification. It defines hazardous areas as areas where flammable gases or vapors may be present. Areas are classified into zones based on the likelihood and duration of an explosive atmosphere occurring. Zone 0 areas have explosive atmospheres present continuously, Zone 1 areas have them likely to occur occasionally, and Zone 2 areas are not likely but possible for short periods. Selection of electrical equipment depends on the area classification and gas properties. Standards provide guidelines for equipment certification to ensure safe operation in hazardous environments.
Tank protection
This document discusses various methods for applying foam to storage tanks for fire protection, including fixed surface systems, seal area protection, and subsurface foam injection. It provides design guidelines for each method, such as minimum application rates and durations. It also describes Williams' foam chambers and foam makers that can be used for fixed surface application through discharge outlets. The foam chambers are available in custom sizes and flows, and can accommodate dual agents. Supplementary application in diked areas is also addressed.
Torpedo
1. A torpedo is a self-propelled underwater weapon used to destroy ships. It consists of a propulsion system, guidance system, and explosive warhead.
2. Torpedoes can be guided by wires or wireless radio signals. The most common propulsion systems are electric motors or Otto fuel engines, since jets require oxygen.
3. India's newest torpedo is the Varunastra, which has a high explosive warhead, electric engine, and wire guidance system for attacking submarines up to 40 km away.
Fm 200
FM200 is a colourless gas which is liquified under pressure for storage. Like Halon 1301 it has a low toxicity level and is superpressurised with Nitrogen to 24.8bar (360psi). It rapidly extinguishes most commonly found fires through a combination of chemical and physical mechanisms.
fire & gas detection system
This document discusses fire and gas detection systems. It begins by defining fire and gases, explaining that fire is a chain reaction between fuel and oxygen that produces heat, light and other byproducts. Gases disperse and mix rapidly. Detection systems are needed to monitor hazardous gas levels and provide early warning before hazards form. They protect people, infrastructure and the environment per safety laws and codes. Detection considers flammable, toxic and asphyxiant gas risks. The document then covers gas properties, ignition risks, limits of flammability, and detection technology types like infrared and catalytic sensors. It stresses the importance of instrument calibration and certification to ensure accurate measurements. Examples of industrial accidents caused by gas leaks are also provided.
LPG – Liquefied Petroleum Gas & Gas Detection System
This document provides information about LPG (liquefied petroleum gas) and gas detection systems. It discusses what LPG is, how it is used to supply buildings and various appliances, and the components of LPG and gas detection systems including piping, outlets, sensors, panels, and standards. The document also outlines procedures for installing, testing, commissioning, maintaining and operating LPG and gas detection systems. Calculations for LPG demand, storage, and pipe sizing are presented.
What's hot (20)
Hazardous area module- Zones, Method of Determination of Hazardous area Radiu...
Hazardous area module- Zones, Method of Determination of Hazardous area Radiu...
Hazardous Area Location Guide - IEC NEC CEC & ATEX By Emerson Industrial
Hazardous Area Location Guide - IEC NEC CEC & ATEX By Emerson Industrial
OISD-STD-117 Fire Protection Facilities for Petroleum Depots, Terminals, Pipe...
OISD-STD-117 Fire Protection Facilities for Petroleum Depots, Terminals, Pipe...
Hazardous area classification and control of ignition sources
Hazardous area classification and control of ignition sources
Clean agents fire suppression system- fm200, novec 1230 and ecaro 25
Clean agents fire suppression system- fm200, novec 1230 and ecaro 25
LPG – Liquefied Petroleum Gas & Gas Detection System
LPG – Liquefied Petroleum Gas & Gas Detection System
Viewers also liked
Intrinsic safety and flameproof apparatus in mines
mine environment engineering
Intrinsic safety and flameproof apparatus in mines
research and development on explosions in mines
prevention of explosion in mines
Lunch And Learn Presentation
This document provides an overview of R.Stahl Inc., which offers explosion protected products for hazardous locations. The agenda covers explosion protection methods, barriers and isolators, remote I/O, HMIs, and system solutions. Details are then given on R.Stahl's electrical, lighting, and automation products, as well as their system capabilities and sources of additional information. Basics of intrinsic safety and nonincendive protection are also summarized.
A users guide to intrinsic safety
This document provides an overview of intrinsic safety and why it is chosen for instrumentation systems in hazardous areas. It discusses that intrinsic safety (1) prevents explosions by ensuring low energy levels, (2) can be used in all zones as it is the only technique proven safe in Zone 0, and (3) permits live maintenance without gas clearance as fault conditions are considered in the design. Intrinsic safety works by restricting electrical energy to below ignition levels and uses three levels ('ia', 'ib', 'ic') that balance explosion risk against ignition risk for the zone.
Intrinsic Safety in a Nutshell by Pepperl+Fuchs
A hazardous area refers to any location with combustible materials that could cause an explosion. An intrinsically safe electrical circuit uses very low energy levels that cannot cause an explosion. Barriers are a key part of intrinsic safety systems as they limit energy to hazardous areas. Intrinsic safety is the safest, least expensive method to protect hazardous areas.
Concepts of Process Instrument Calibration
This document discusses calibration in the measuring technology industry, specifically as it relates to KROHNE. It provides definitions of calibration and discusses why calibration is important. Calibration ensures measuring devices are accurate by comparing them to reference devices and standards. KROHNE calibrating facilities include an elevated tank calibration facility for flowmeters up to 120 m3/h and a large air calibration rig for flows up to 2500 m3/h.
Intrinsic safety
Intrinsic safety is a technique used to prevent explosions caused by sparking electrical apparatus in hazardous areas. It works by using safety barriers between safe and hazardous areas to prevent faults from generating high energy sparks that could ignite explosive mixtures. Intrinsically safe circuits are designed and implemented to not produce any sparks at all. Simple low power devices like thermocouples can be used without barriers in hazardous areas. Intrinsic safety is the preferred method for zone 0 areas and offers flexibility in circuit design while eliminating explosion proof junction boxes. However, it is limited to low power applications like instruments and controls.
Pepperl + Fuchs' Emerson Global User Exchange highlights!
Check out the highlights from the Pepperl+Fuchs booth during the 2011 Emerson Global Users Exchange held at the Gaylord Opryland Resort & Convention Center.
#EMRex and @PepperlFuchsUSA
Ex ic Intrinsic Safety New Protection Level
Introducing a new technology: Ex ic. Read our PDF for more information. Visit http://www.extech.co.za/
Exloc is hj
This document provides an overview of intrinsic safety and area classification. It discusses the need for intrinsic safety in hazardous locations where flammable gases or vapors may be present. Intrinsic safety works by limiting the voltage, current, and stored energy in electrical equipment to levels that cannot cause ignition. The document defines intrinsic safety and area classification standards. It examines the basic principles of intrinsic safety design and certification. Key topics covered include explosion triangles, temperature ratings, gas grouping, purging, and grounding requirements for intrinsic safety installations.
DEVELOPMENT OF NEUROFUZZY CONTROL SYSTEM FOR THE GUIDANCE OF AIR TO AIR MISS...
DEVELOPMENT OF NEUROFUZZY CONTROL SYSTEM FOR THE GUIDANCE OF AIR TO AIR MISS...Ahmed Momtaz Hosny, PhD
This document summarizes a thesis on developing a neurofuzzy control system for guiding air-to-air missiles. It includes sections on AIM 9 missile modeling, control strategies using neural networks and fuzzy logic, computer simulations, and conclusions. Control strategies include using neural networks, fuzzy logic, and a hybrid neurofuzzy system. Comparisons are made between different controller types using integrated square error. The thesis recommends applying the control techniques practically and optimizing guidance based on predicted target maneuver data.Naval Aircraft & Missiles Web
The document provides an overview of various naval aircraft, missiles, and weapons systems used by the US Navy. It describes the main categories of aircraft as fixed-wing, rotary-wing, and lighter-than-air. It then discusses different types of naval aircraft like attack planes, fighter planes, patrol aircraft, electronic warfare aircraft, and reconnaissance aircraft. The document also summarizes naval missiles from guided missiles to ballistic missiles and cruise missiles. It concludes with a brief overview of naval torpedoes and underwater warfare systems.
Tactical Missile Design
This three-sentence summary provides the key details about the document:
The document announces a three-day short course on tactical missile design integration that will cover fundamentals of missile configuration, propulsion, weight, performance, and integration considerations. The course, taught by experienced instructor Eugene Fleeman, will use analytical expressions and examples to illustrate the primary design drivers and tradeoffs. Attendees will learn missile design processes and parameters, participate in a small rocket design exercise, and receive course notes and a textbook on tactical missile design.
BHEL HARIDWAR,CONSTRUCTION OF TURBO GENERATOR AND EXCITATION SYSTEM
This document provides an overview of the vocational training received at Bharat Heavy Electricals Limited (BHEL) in Haridwar, India focusing on turbo generators. It describes the various sections and blocks at BHEL Haridwar involved in manufacturing turbo generators and their components. Key points include that BHEL Haridwar is divided into a Central Foundry Forge Plant and a Heavy Electrical Equipment Plant, and within the latter are blocks focused on manufacturing the turbo generator and exciter system, power equipment, steam and gas turbines, windings, water boxes and more. The document also provides details on the components, workings, classifications and manufacturing process of turbo generators.
Pepperl fuchs 2011 Emerson Global Users Exchange Intrinsically Safe CHARMS S...
Check out the Intrinsically Safe CHARMS joint presentation between Pepperl+Fuchs and Emerson from the 2011 Emerson Global Users Exchange
JobScout Media Kit
jobscout is a platform that teaches digital literacy skills through gamified lessons to help users learn how to conduct an independent online job search. It provides tools like a resume builder, job search functionality, and social networking opportunities to help users find employment. The service began as a solution for libraries that needed to help patrons learn job searching online, and has now expanded to partner with other organizations and address issues like unemployment and the digital divide.
Modelos de negocio para distribución de contenido creativo por Internet
Presentación de la conferencia que di en el Taller nacional sobre propiedad intelectual e industrias Creativas (http://j.mp/LgKx6x) celebrado el 12 de junio en instalaciones de la FLACSO (Quito).
El tema era "Modelos de negocio para distribución de contenido creativo" y yo me centré en herramientas y ejemplos para hacerlo por Internet.
Award-CC: Dokumentation 2016 für Partner und Sponsoren
Der Swiss Award Corporate Communications - Swiss Award-CC - ist der einzigste Schweizer Preis für Unternehmenskommunikation. Erfahre in der Partner Dokumentation alles über den Preis.
E-Wave Networks PVT. LTD>
E-Wave Networks is an ISO-certified telecom company that provides RF and in-building solutions services. It was founded in 2010 by telecom professionals to diversify into these services areas. The company has three business models: projects, manpower management, and training. It offers a wide range of telecom network services including planning, optimization, installation, and maintenance. E-Wave has experience with over 35,000 RF surveys, 20,000 LOS surveys, and 25,000 EMF surveys. It recruits and trains engineers and has participated in campus placements at various technical institutes.
El Proyecto Matriz 5 Constitucion Europea La Gran Mentira
El documento presenta una discusión sobre el Tratado Constitucional de la Unión Europea, el cual fue sometido a referéndum en varios países miembros. Explica que en Francia y Holanda ganó el voto en contra del tratado, mientras que en España ganó el voto a favor, debido a diferencias en el nivel de información provisto a los ciudadanos. También describe la labor de Etienne Chouard, profesor francés que analizó críticamente el tratado en su blog y ayudó a informar a los votantes franceses sobre
Salida o campamento
Este documento ofrece instrucciones para organizar una salida o campamento de la asociación GS San Viator. Detalla los pasos para reservar un refugio de la red de la CAM, incluyendo fechas, solicitud, pago e información requerida. También proporciona consejos sobre planificar actividades, menús, transporte y presupuesto para que la salida sea un éxito.
Viewers also liked (20)
Intrinsic safety and flameproof apparatus in mines
Intrinsic safety and flameproof apparatus in mines
Pepperl + Fuchs' Emerson Global User Exchange highlights!
Pepperl + Fuchs' Emerson Global User Exchange highlights!
DEVELOPMENT OF NEUROFUZZY CONTROL SYSTEM FOR THE GUIDANCE OF AIR TO AIR MISS...
DEVELOPMENT OF NEUROFUZZY CONTROL SYSTEM FOR THE GUIDANCE OF AIR TO AIR MISS...
BHEL HARIDWAR,CONSTRUCTION OF TURBO GENERATOR AND EXCITATION SYSTEM
BHEL HARIDWAR,CONSTRUCTION OF TURBO GENERATOR AND EXCITATION SYSTEM
Pepperl fuchs 2011 Emerson Global Users Exchange Intrinsically Safe CHARMS S...
Pepperl fuchs 2011 Emerson Global Users Exchange Intrinsically Safe CHARMS S...
Modelos de negocio para distribución de contenido creativo por Internet
Modelos de negocio para distribución de contenido creativo por Internet
Award-CC: Dokumentation 2016 für Partner und Sponsoren
Award-CC: Dokumentation 2016 für Partner und Sponsoren
El Proyecto Matriz 5 Constitucion Europea La Gran Mentira
El Proyecto Matriz 5 Constitucion Europea La Gran Mentira
More from Belilove Company-Engineers
BCE’s Vacuum Ring Heater
Providing uniform heat to semiconductor devices in degassing chambers is essential in extracting impurities. This can only be achieved if a heating device has the proper fit and temperature uniformity for a given chamber. It is for this very application that BCE was approached by a large semiconductor company from Silicon Valley. In order to heat this company’s semiconductor wafers, it was critical that the heating device be manufactured to fit precisely into a large and circular degassing chamber posing manufacturing challenges due to dimensional and application parameters. BCE was able to provide extensive design consultations, 3D CAD modeling and lean manufacturing capabilities to this semiconductor giant at a competitive price. All these services were rendered while catering to all requirements needed to successfully manufacture their products.
BCE SUPERCIRC Heater
A compact, fast responding electric heating element for clean gases in fuel cell, bio-med, laboratory, food, and pharmaceutical applications. The SuperCirc gas heater is designed for applications where fast heating of clean gases is required. All parts exposed to gas flow are constructed of 316SS (other materials available) rather than exposing process media to exposed resistance elements. This ensures that no foreign matter contaminates gas.
General Specification for Thermofoil Heater, All-Polyimide, Space Applications
General Specification for Thermofoil Heater, All-Polyimide, Space ApplicationsBelilove Company-Engineers
Purpose. This specification establishes the requirements for thermofoil heaters of an all- polyimide (adhesive-less) construction for high reliability space applications. It defines the process, test verification, and inspections required by product used in space flight applications.BCE Flanged, Replaceable, Multi-Thermocouple Feedthroughs
One of the biggest challenges facing the vacuum industry is to collect multiple readings from complex assemblies while being limited by the number of existing feedthrough ports in a vacuum chamber. With BCE’s Multi-TC, Flanged Feedthrough, companies no longer need to invest in adding more ports for a greater collection of temperatures from a vacuum environment as multiple thermocouples are embedded in just one feedthrough. The number, type and lengths of the thermocouples can be altered to match specific application requirements meeting each customers’ unique needs. As the thermocouples can be adapted to meet unique design constraints, so can this feedthrough’s flange. All sizes used are standard and are easily mountable with readily available hardware. No complicated assemblies are required for the most complicated of vacuum setups.
With most vacuum feedthroughs, troubleshooting can be difficult as well when multiple fixed elements are involved. If one element fails, generally the entire vacuum feedthrough is rendered useless. With BCE’s Multi-TC, Flanged Feedthrough, arduous troubleshooting procedures are a thing of the past. In fact, this feedthrough’s thermocouples are replaceable as they can be extracted from the compression fittings with great ease. This means that if thermocouples fail, they can be removed, tested and replaced within minutes. Thus, this no-hassle design allows for faster, more accurate and more cost-effective thermal data collection. Trust BCE’s Multi-TC, Flanged Feedthrough for your most complicated thermal detection needs.
NASA Preferred Reliability Practices Vacuum Seals Design Criteria
Practice:
Well made, clamped, and temperature stabilized circular O-rings should be used in the design of
reliable, reusable and long life seals in vacuum sealing applications. Benefits:
Leak free flanges as well as low/undetectable outgassing of the elastomeric materials can be achieved at pressure levels as low as 10-8 Torr by using well made O-rings in a static vacuum seal environment. The use of O-rings has provided ease for running environmental tests on the ground using space simulation chambers.
Heaters for process air and gases
The Air Process heater will provide hot air and gas up to 1000 degree Fahrenheit (540 C) with infinite control by varying the voltage and air velocity supplied. Units are fitted with a tubing "T" for convenient power lead outlet, while larger diameters can be supplied with post terminals on the sheath for direct electrical connections.
Magnetic Level Indicator Selection Guide
Orion Instruments specializes in high-visibility magnetic level indication and high-accuracy magnetostrictive level transmitters. Magnetic level indicators provide high visibility local indication of liquid level in tanks and vessels.
Liquid Turbine Flow Meter
BARTON 7000 Series liquid turbine meters are designed for a broad range of precise liquid measurement applications. Based on more than 40 years of turbine manufacturing experience, this built-to-order series features a range of sizes, materials, bearing systems, and options.
Application of alarm annunciator as cyber security layer
DCS/PLC and SCADA control systems, though they provide immense capability, share a common weakness. Both are subject to cyber attack from external sources. The potential impact of this vulnerability should not be dismissed. An annunciator system can be put in place that will monitor critical process elements and provide notification of abnormalities. The systems, whether hardwired or software based, are isolated, allowing them to act as a failsafe or backup to the main control and monitoring system.
Selecting the Right Magnetic Level Indicator (MLI)
Companies in the process industry need the ability to visually monitor liquid levels in vessels (boilers, storage tanks, processing units, etc.). Traditionally, armored glass sight gauges have been used. However, many companies want an alternative to sight gauges to avoid problems such as breakage, leaks, or bursting at high pressures and extreme temperatures. In addition, the visibility of the sight glass can be poor and often affected by moisture, corrosion, or oxidation.
Magnetic level indicators (MLIs) do not have the shortcomings of glass sight gauges and are suitable for a wide variety of installations.
Installation Operation Manual for Brooks GF100 Series
Designed for semiconductor, MOCVD and other gas flow control applications, the GF100 series exceeds the semiconductor industry standard for reliability, ensuring repeatable, highly stable performance over time. Standard MultiFlo technology enables one MFC to support thousands of gas types and range combinations without removing it from the gas line or compromising on accuracy.
Process Heaters, Furnaces and Fired Heaters: Improving Efficiency and Reducin...
Process Heaters, Furnaces and Fired Heaters: Improving Efficiency and Reducin...Belilove Company-Engineers
A process heater is a direct-fired heat exchanger that uses the hot gases of combustion to raise the temperature of a feed owing through coils of tubes aligned throughout the heater. Depending on the use, these are also called furnaces or red heaters. Some heaters simply deliver the feed at a predetermined temperature to the next stage of the reaction process; others perform reactions on the feed while it travels through the tubes.Comparing Industrial Level Displacer Transmitter Technologies
Process level measurement has greatly evolved over the years with new technologies. Instrumentation engineers have more demanding requirements that make it essential to have reliable and accurate liquid level measurements. Although based on a more traditional level measurement technology, one of the most trusted devices for continuous liquid level measurement remains the displacer level transmitter
Ammonium & Nitrate Analyzers for Water Treatment
The HYDRA analyzers are a family of nitrogen analyzers that measure ammonium or nitrate using a single integrated sensor. The HYDRA-NH4 and HYDRA-NO3 sensors measure these compounds in municipal and environmental water applications. Key features include automatic compensation for interfering ions and temperature, integrated spray cleaning, and configurable alarm outputs. The sensors have replaceable electrodes and require minimal maintenance.
Optimizing the Steam Generation Cycle and Condensate Recovery Process
The document discusses how improving instrumentation and level control in steam generation and condensate recovery systems can increase efficiency and reduce costs for industries that rely heavily on steam. Key areas that better level measurement can optimize include the boiler/steam drum, deaerator, feedwater heaters, blowdown flash tank, condensate receiver tanks, and heat exchangers. Technologies like guided wave radar that are unaffected by process conditions can provide more accurate level measurement and eliminate sources of error compared to differential pressure, buoyancy, or other inferential methods. This allows tighter control of levels throughout the steam cycle for maximum heat transfer, less blowdown waste, and recovery of more condensate for fuel and water savings.
Control Valves for the Power Generation Industry" A Product and Applications ...
Control Valves for the Power Generation Industry" A Product and Applications ...Belilove Company-Engineers
This document provides an overview of control valves for the power generation industry. It discusses the various systems in a conventional thermal power plant such as the condensate system, feedwater system, and main steam system. It then summarizes several case studies of Trimteck supplying control valves for applications in these systems for power plants. These include valves for condenser level control, boiler burner purge cycles, compressor reject control, turbine bypass, and superheater attemperation spray. The document promotes Trimteck as offering a full line of high quality control valves and solutions for flow control problems in power plants.Combustion Analyzer to Add Extra Layer of Safety to Burner Management System
Combustion Analyzer to Add Extra Layer of Safety to Burner Management SystemBelilove Company-Engineers
The reliable identification of low combustion oxygen in a red heater or boiler has always been critical to the effectiveness of the Burner Management System for proper control and safety.
Low emission burners and aggressive ring control points to achieve increased efficiency and emission reductions have driven the industry to tighter control measures. But tighter control measures also hold a greater potential for combustion damage. Reducing the risk of a combustion event has become a priority and has led to the implementation of Safety Instrumented Systems (SIS). This additional layer of safety is added to the Basic Process Control System.Applying Thin Film Coatings in Medical Devices
Society has benefited tremendously from the development and utilization of mechanical devices which are implanted inside the body and are used to replace bones and joints, increase blood flow, and even measure blood chemistry. To further enhance the performance of these devices, the application of thin films to the external surfaces is an ongoing research and development interest at many companies. Engineers have a choice of a variety of technologies to apply these liquid coatings to these often complex surfaces ranging from vacuum technology to direct liquid application. The decision on what technology to use is a function of the liquid precursor used, the mechanism of coating formation and the geometry of the object to be coated. A critical quality and process control criterion is the consistency of the coating on the surface. Fluid delivery technology can play an important part in maintaining coating consistency. Pumps and liquid flow controllers are technologies being used today. For vapor coating processes, liquid vaporization technology is a critical link in the fluid delivery system. New flow and vaporization technology is available that can be applied to fluid delivery to improve the application of medical device coatings.
BCE Custom Vacuum Feedthroughs
THE NEED
Equipment manufacturers and scientific researchers are continually challenged with supplying power, fiber-optic, control, and monitoring cables through sealed vacuum vessels. Whether due to space restrictions, special geometries, or number and type of conductors, standard glass-to-metal or ceramic feedthroughs never quite fit the bill. Unfortunately, because of limited options, many designers are forced to compromise and go for an off-the-shelf solution.
EPOXY TO THE RESCUE.
During the past decade, new epoxy compounds have been developed that rival glass and ceramic in performance. BCE is at the forefront of this development.
With modern epoxy feedthroughs, any kind of standard or custom connector is sealed in a completely potted, high-performance, clear epoxy compound. Epoxy seals offer countless design options, and most amazingly, performance equal to or better than glass or ceramic. Better yet, pricing is very competitive and quick turn-around for prototypes and short production runs are not a problem.
Electric Heating Element Technical Reference Guide
Electric heater application reference guide with look-up tables for important thermal engineering constants and properties.
More from Belilove Company-Engineers (20)
General Specification for Thermofoil Heater, All-Polyimide, Space Applications
General Specification for Thermofoil Heater, All-Polyimide, Space Applications
BCE Flanged, Replaceable, Multi-Thermocouple Feedthroughs
BCE Flanged, Replaceable, Multi-Thermocouple Feedthroughs
NASA Preferred Reliability Practices Vacuum Seals Design Criteria
NASA Preferred Reliability Practices Vacuum Seals Design Criteria
Application of alarm annunciator as cyber security layer
Application of alarm annunciator as cyber security layer
Selecting the Right Magnetic Level Indicator (MLI)
Selecting the Right Magnetic Level Indicator (MLI)
Installation Operation Manual for Brooks GF100 Series
Installation Operation Manual for Brooks GF100 Series
Process Heaters, Furnaces and Fired Heaters: Improving Efficiency and Reducin...
Process Heaters, Furnaces and Fired Heaters: Improving Efficiency and Reducin...
Comparing Industrial Level Displacer Transmitter Technologies
Comparing Industrial Level Displacer Transmitter Technologies
Optimizing the Steam Generation Cycle and Condensate Recovery Process
Optimizing the Steam Generation Cycle and Condensate Recovery Process
Control Valves for the Power Generation Industry" A Product and Applications ...
Control Valves for the Power Generation Industry" A Product and Applications ...
Combustion Analyzer to Add Extra Layer of Safety to Burner Management System
Combustion Analyzer to Add Extra Layer of Safety to Burner Management System
Electric Heating Element Technical Reference Guide
Electric Heating Element Technical Reference Guide
Recently uploaded
artificial intelligence and data science contents.pptx
What is artificial intelligence? Artificial intelligence is the ability of a computer or computer-controlled robot to perform tasks that are commonly associated with the intellectual processes characteristic of humans, such as the ability to reason.
› ...
Artificial intelligence (AI) | Definitio
原版制作(Humboldt毕业证书)柏林大学毕业证学位证一模一样
原件一模一样【微信：bwp0011】《(Humboldt毕业证书)柏林大学毕业证学位证》【微信：bwp0011】学位证，留信认证（真实可查，永久存档）原件一模一样纸张工艺/offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原。
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问微bwp0011
【主营项目】
一.毕业证【微bwp0011】成绩单、使馆认证、教育部认证、雅思托福成绩单、学生卡等！
二.真实使馆公证(即留学回国人员证明,不成功不收费)
三.真实教育部学历学位认证（教育部存档！教育部留服网站永久可查）
四.办理各国各大学文凭(一对一专业服务,可全程监控跟踪进度)
如果您处于以下几种情况：
◇在校期间，因各种原因未能顺利毕业……拿不到官方毕业证【微bwp0011】
◇面对父母的压力，希望尽快拿到；
◇不清楚认证流程以及材料该如何准备；
◇回国时间很长，忘记办理；
◇回国马上就要找工作，办给用人单位看；
◇企事业单位必须要求办理的
◇需要报考公务员、购买免税车、落转户口
◇申请留学生创业基金
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
Rainfall intensity duration frequency curve statistical analysis and modeling...
Using data from 41 years in Patna’ India’ the study’s goal is to analyze the trends of how often it rains on a weekly, seasonal, and annual basis (1981−2020). First, utilizing the intensity-duration-frequency (IDF) curve and the relationship by statistically analyzing rainfall’ the historical rainfall data set for Patna’ India’ during a 41 year period (1981−2020), was evaluated for its quality. Changes in the hydrologic cycle as a result of increased greenhouse gas emissions are expected to induce variations in the intensity, length, and frequency of precipitation events. One strategy to lessen vulnerability is to quantify probable changes and adapt to them. Techniques such as log-normal, normal, and Gumbel are used (EV-I). Distributions were created with durations of 1, 2, 3, 6, and 24 h and return times of 2, 5, 10, 25, and 100 years. There were also mathematical correlations discovered between rainfall and recurrence interval.
Findings: Based on findings, the Gumbel approach produced the highest intensity values, whereas the other approaches produced values that were close to each other. The data indicates that 461.9 mm of rain fell during the monsoon season’s 301st week. However, it was found that the 29th week had the greatest average rainfall, 92.6 mm. With 952.6 mm on average, the monsoon season saw the highest rainfall. Calculations revealed that the yearly rainfall averaged 1171.1 mm. Using Weibull’s method, the study was subsequently expanded to examine rainfall distribution at different recurrence intervals of 2, 5, 10, and 25 years. Rainfall and recurrence interval mathematical correlations were also developed. Further regression analysis revealed that short wave irrigation, wind direction, wind speed, pressure, relative humidity, and temperature all had a substantial influence on rainfall.
Originality and value: The results of the rainfall IDF curves can provide useful information to policymakers in making appropriate decisions in managing and minimizing floods in the study area.
哪里办理(csu毕业证书)查尔斯特大学毕业证硕士学历原版一模一样
原版一模一样【微信：741003700 】【(csu毕业证书)查尔斯特大学毕业证硕士学历】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
一比一原版(CalArts毕业证)加利福尼亚艺术学院毕业证如何办理
CalArts毕业证学历书【微信95270640】CalArts毕业证’圣力嘉学院毕业证《Q微信95270640》办理CalArts毕业证√文凭学历制作{CalArts文凭}购买学历学位证书本科硕士,CalArts毕业证学历学位证【实体公司】办毕业证、成绩单、学历认证、学位证、文凭认证、办留信网认证、（网上可查，实体公司，专业可靠）
(诚招代理)办理国外高校毕业证成绩单文凭学位证,真实使馆公证（留学回国人员证明）真实留信网认证国外学历学位认证雅思代考国外学校代申请名校保录开请假条改GPA改成绩ID卡
1.高仿业务:【本科硕士】毕业证,成绩单（GPA修改）,学历认证（教育部认证）,大学Offer,,ID,留信认证,使馆认证,雅思,语言证书等高仿类证书；
2.认证服务: 学历认证（教育部认证）,大使馆认证（回国人员证明）,留信认证（可查有编号证书）,大学保录取,雅思保分成绩单。
3.技术服务：钢印水印烫金激光防伪凹凸版设计印刷激凸温感光标底纹镭射速度快。
办理加利福尼亚艺术学院加利福尼亚艺术学院毕业证文凭证书流程：
1客户提供办理信息：姓名生日专业学位毕业时间等（如信息不确定可以咨询顾问：我们有专业老师帮你查询）；
2开始安排制作毕业证成绩单电子图；
3毕业证成绩单电子版做好以后发送给您确认；
4毕业证成绩单电子版您确认信息无误之后安排制作成品；
5成品做好拍照或者视频给您确认；
6快递给客户（国内顺丰国外DHLUPS等快读邮寄）
-办理真实使馆公证（即留学回国人员证明）
-办理各国各大学文凭（世界名校一对一专业服务,可全程监控跟踪进度）
-全套服务：毕业证成绩单真实使馆公证真实教育部认证。让您回国发展信心十足！
（详情请加一下 文凭顾问+微信:95270640）欢迎咨询！子小伍玩小伍比山娃小一岁虎头虎脑的很霸气父亲让山娃跟小伍去夏令营听课山娃很高兴夏令营就设在附近一所小学山娃发现那所小学比自己的学校更大更美操场上还铺有塑胶跑道呢里面很多小朋友一班一班的快快乐乐原来城里娃都藏这儿来了怪不得平时见不到他们山娃恍然大悟起来吹拉弹唱琴棋书画山娃都不懂却什么都想学山娃怨自己太笨什么都不会斟酌再三山娃终于选定了学美术当听说每月要交元时父亲犹豫了山娃也说爸算了吧咱学校一学期才转
Comparative analysis between traditional aquaponics and reconstructed aquapon...
The aquaponic system of planting is a method that does not require soil usage. It is a method that only needs water, fish, lava rocks (a substitute for soil), and plants. Aquaponic systems are sustainable and environmentally friendly. Its use not only helps to plant in small spaces but also helps reduce artificial chemical use and minimizes excess water use, as aquaponics consumes 90% less water than soil-based gardening. The study applied a descriptive and experimental design to assess and compare conventional and reconstructed aquaponic methods for reproducing tomatoes. The researchers created an observation checklist to determine the significant factors of the study. The study aims to determine the significant difference between traditional aquaponics and reconstructed aquaponics systems propagating tomatoes in terms of height, weight, girth, and number of fruits. The reconstructed aquaponics system’s higher growth yield results in a much more nourished crop than the traditional aquaponics system. It is superior in its number of fruits, height, weight, and girth measurement. Moreover, the reconstructed aquaponics system is proven to eliminate all the hindrances present in the traditional aquaponics system, which are overcrowding of fish, algae growth, pest problems, contaminated water, and dead fish.
学校原版美国波士顿大学毕业证学历学位证书原版一模一样
原版一模一样【微信：741003700 】【美国波士顿大学毕业证学历学位证书】【微信：741003700 】学位证，留信认证（真实可查，永久存档）offer、雅思、外壳等材料/诚信可靠,可直接看成品样本，帮您解决无法毕业带来的各种难题！外壳，原版制作，诚信可靠，可直接看成品样本。行业标杆！精益求精，诚心合作，真诚制作！多年品质 ,按需精细制作，24小时接单,全套进口原装设备。十五年致力于帮助留学生解决难题，包您满意。
本公司拥有海外各大学样板无数，能完美还原海外各大学 Bachelor Diploma degree, Master Degree Diploma
1:1完美还原海外各大学毕业材料上的工艺：水印，阴影底纹，钢印LOGO烫金烫银，LOGO烫金烫银复合重叠。文字图案浮雕、激光镭射、紫外荧光、温感、复印防伪等防伪工艺。材料咨询办理、认证咨询办理请加学历顾问Q/微741003700
留信网认证的作用:
1:该专业认证可证明留学生真实身份
2:同时对留学生所学专业登记给予评定
3:国家专业人才认证中心颁发入库证书
4:这个认证书并且可以归档倒地方
5:凡事获得留信网入网的信息将会逐步更新到个人身份内，将在公安局网内查询个人身份证信息后，同步读取人才网入库信息
6:个人职称评审加20分
7:个人信誉贷款加10分
8:在国家人才网主办的国家网络招聘大会中纳入资料，供国家高端企业选择人才
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building.pdf
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building
An improved modulation technique suitable for a three level flying capacitor ...
This research paper introduces an innovative modulation technique for controlling a 3-level flying capacitor multilevel inverter (FCMLI), aiming to streamline the modulation process in contrast to conventional methods. The proposed
simplified modulation technique paves the way for more straightforward and
efficient control of multilevel inverters, enabling their widespread adoption and
integration into modern power electronic systems. Through the amalgamation of
sinusoidal pulse width modulation (SPWM) with a high-frequency square wave
pulse, this controlling technique attains energy equilibrium across the coupling
capacitor. The modulation scheme incorporates a simplified switching pattern
and a decreased count of voltage references, thereby simplifying the control
algorithm.
22CYT12-Unit-V-E Waste and its Management.ppt
Introduction- e - waste – definition - sources of e-waste– hazardous substances in e-waste - effects of e-waste on environment and human health- need for e-waste management– e-waste handling rules - waste minimization techniques for managing e-waste – recycling of e-waste - disposal treatment methods of e- waste – mechanism of extraction of precious metal from leaching solution-global Scenario of E-waste – E-waste in India- case studies.
Applications of artificial Intelligence in Mechanical Engineering.pdf
Historically, mechanical engineering has relied heavily on human expertise and empirical methods to solve complex problems. With the introduction of computer-aided design (CAD) and finite element analysis (FEA), the field took its first steps towards digitization. These tools allowed engineers to simulate and analyze mechanical systems with greater accuracy and efficiency. However, the sheer volume of data generated by modern engineering systems and the increasing complexity of these systems have necessitated more advanced analytical tools, paving the way for AI.
AI offers the capability to process vast amounts of data, identify patterns, and make predictions with a level of speed and accuracy unattainable by traditional methods. This has profound implications for mechanical engineering, enabling more efficient design processes, predictive maintenance strategies, and optimized manufacturing operations. AI-driven tools can learn from historical data, adapt to new information, and continuously improve their performance, making them invaluable in tackling the multifaceted challenges of modern mechanical engineering.
Use PyCharm for remote debugging of WSL on a Windo cf5c162d672e4e58b4dde5d797...
This document serves as a comprehensive step-by-step guide on how to effectively use PyCharm for remote debugging of the Windows Subsystem for Linux (WSL) on a local Windows machine. It meticulously outlines several critical steps in the process, starting with the crucial task of enabling permissions, followed by the installation and configuration of WSL.
The guide then proceeds to explain how to set up the SSH service within the WSL environment, an integral part of the process. Alongside this, it also provides detailed instructions on how to modify the inbound rules of the Windows firewall to facilitate the process, ensuring that there are no connectivity issues that could potentially hinder the debugging process.
The document further emphasizes on the importance of checking the connection between the Windows and WSL environments, providing instructions on how to ensure that the connection is optimal and ready for remote debugging.
It also offers an in-depth guide on how to configure the WSL interpreter and files within the PyCharm environment. This is essential for ensuring that the debugging process is set up correctly and that the program can be run effectively within the WSL terminal.
Additionally, the document provides guidance on how to set up breakpoints for debugging, a fundamental aspect of the debugging process which allows the developer to stop the execution of their code at certain points and inspect their program at those stages.
Finally, the document concludes by providing a link to a reference blog. This blog offers additional information and guidance on configuring the remote Python interpreter in PyCharm, providing the reader with a well-rounded understanding of the process.
AI assisted telemedicine KIOSK for Rural India.pptx
It gives the overall description of SIH problem statement " AI assisted telemedicine KIOSK for Rural India".
Software Engineering and Project Management - Introduction, Modeling Concepts...
Introduction, Modeling Concepts and Class Modeling: What is Object orientation? What is OO development? OO Themes; Evidence for usefulness of OO development; OO modeling history. Modeling
as Design technique: Modeling, abstraction, The Three models. Class Modeling: Object and Class Concept, Link and associations concepts, Generalization and Inheritance, A sample class model, Navigation of class models, and UML diagrams
Building the Analysis Models: Requirement Analysis, Analysis Model Approaches, Data modeling Concepts, Object Oriented Analysis, Scenario-Based Modeling, Flow-Oriented Modeling, class Based Modeling, Creating a Behavioral Model.
Recently uploaded (20)
artificial intelligence and data science contents.pptx
artificial intelligence and data science contents.pptx
Rainfall intensity duration frequency curve statistical analysis and modeling...
Rainfall intensity duration frequency curve statistical analysis and modeling...
Comparative analysis between traditional aquaponics and reconstructed aquapon...
Comparative analysis between traditional aquaponics and reconstructed aquapon...
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building.pdf
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building.pdf
An improved modulation technique suitable for a three level flying capacitor ...
An improved modulation technique suitable for a three level flying capacitor ...
Engineering Drawings Lecture Detail Drawings 2014.pdf
Engineering Drawings Lecture Detail Drawings 2014.pdf
Applications of artificial Intelligence in Mechanical Engineering.pdf
Applications of artificial Intelligence in Mechanical Engineering.pdf
Use PyCharm for remote debugging of WSL on a Windo cf5c162d672e4e58b4dde5d797...
Use PyCharm for remote debugging of WSL on a Windo cf5c162d672e4e58b4dde5d797...
AI assisted telemedicine KIOSK for Rural India.pptx
AI assisted telemedicine KIOSK for Rural India.pptx
Software Engineering and Project Management - Introduction, Modeling Concepts...
Software Engineering and Project Management - Introduction, Modeling Concepts...