This paper present a design of a Frequency Selective Surface (FSS) to improve gain and efficiency of a microstrip patch antenna operating in X-band at 10 GHz. The band-stop frequency selective surface (FSS) designed at the operating frequency of the antenna is used. FSS structure is configured as a superstrate for the microstrip patch antenna. The main goal of this paper is design a compact microstrip antenna module (microstrip patch and FSS structure). Simulation results using CST studio showed that high gain (54 % increment) and efficiency is increased to 97% have been achieved by the proposed antenna module (MS and FSS). The equivalent circuit of proposed FSS unit cell in ADS software has been evaluated and compared to simulation results (CST studio) to improve characteristics of the antenna. The proposed antenna module is extremely compact high gain and it can be used for X-band applications.
Dual polarized, high-gain sector antenna for mimoprjpublications
This document summarizes the design and testing of a dual-polarized, high-gain sector antenna for MIMO communications systems. It describes the configuration of the antenna, which uses a microstrip Wilkinson power divider and L-shaped probes to feed two square patches. Simulation results are presented analyzing the effects of various structural parameters on antenna performance. Measurements of the fabricated antenna show good agreement with simulations, meeting requirements of VSWR less than 1.4 and gain over 11 dBi across the 3.35-3.65 GHz band. The antenna has advantages of dual polarization, simple structure, and potential for arraying.
The document summarizes a research paper on the design of a frequency reconfigurable monopole antenna with a switchable symmetric slot structure. The antenna is designed to operate across multiple frequency bands by using p-i-n diodes to switch the state of the symmetric slot structure on the ground plane. Five diode combinations are identified that allow the antenna to operate at different single and dual frequency bands between 1.72-9.57 GHz. The simple and compact antenna design makes it suitable for applications requiring reconfiguration across multiple frequency bands like cognitive radio and multi-radio wireless systems.
Compact Rectangular Slot Microstrip Antenna with Band-Notched Characteristics...jmicro
n this paper, we present an offset microstrip-fed ultraw
ideband antenna with band notch
characteristics.The antenna structure consists of rectangular r
adiating patch and ground plane with
rectangular shaped slot, which increases impedance bandwidth upto 1
17.73%(2.9-11.2GHz).A new
modified U slot is etched in the radiating patch to create band-
notched properties in the WiMAX (3.3-
3.7GHz) and C-band satellite communication (3.7-4.15GHz).Further
more, parametric studies have been
conducted using EM simulation software CADFEKO suite(7.0) and
optimized with stable radiation pattern
which satisfied UWB requirement for VSWR<2.A prototype of ante
nna is fabricated on 1.6mm thick FR-4
substrate with dielectric constant of 4.4 and loss tangent of 0.02
.The designed antenna exhibits
bidirectional and omni directional radiation patterns along E and
H-plane with stable gain and efficiency
over entire operating band except notch frequency band. Simulated res
ults are in good agreement with the
measured results of the proposed antenna which makes it a good
candidate for UWB application.
International Journal of Computational Engineering Research(IJCER)ijceronline
This document discusses using a triangular lattice electromagnetic bandgap (EBG) structure in the ground plane of a 2x2 triangular microstrip patch antenna array to improve its bandwidth. The EBG structure provides better antenna gain and a 110% increase in bandwidth compared to the antenna array without EBG. Keywords discussed include equilateral triangular microstrip patch antenna, antenna array, EBG, impedance bandwidth, and triangular lattice.
The document describes the design and simulation of a novel star-shaped fractal slot antenna. The antenna was modified from a triangular microstrip antenna into a star-shaped patch with fractal geometry. This increased the antenna's impedance bandwidth. Simulation results showed the antenna achieved a wide bandwidth of 56.67% from 4.8 GHz to 7.1 GHz, covering WLAN and X-band applications. Within this band, the antenna maintained stable radiation patterns and a gain ranging from 6.33 dBi to 10.02 dBi. Introducing a fractal iteration further improved the bandwidth and gain.
Design and development of triple band ominidirectional slotted rectangular mi...IAEME Publication
This document summarizes the design and development of a triple band slotted rectangular microstrip antenna (TSRMA). Key points:
- TSRMA is designed to operate over three frequency bands from 4.75-16 GHz using rectangular slots on the patch and a ground plane.
- Both simulated and experimental results show TSRMA achieves bandwidths of 260 MHz, 3.113 GHz, and 5.27 GHz across the three bands.
- Radiation patterns measured at the second and third bands were omnidirectional, as desired for applications in microwave systems.
- The simple, low-cost antenna design makes it suitable for systems operating over the 4.75-16 GHz range.
A Three-in-One Diversity Antenna System for 5 GHz WLAN ApplicationsSaou-Wen Su
A novel, three-in-one antenna system suitable for WLAN operation in the 5 GHz band is presented. The design is based upon incorporating one slot and two dipole antennas into a compact multi-antenna system that has comparable dimensions of a single mobile-unit antenna element. The three antennas are arranged parallel to each other with the two dipoles set on the right and left sides of the slot respectively. With this arrangement, not only can compact integration of three individual antennas be realized, pattern diversity and polarization diversity are also obtained. A design prototype has been constructed and tested. The results show that the coupling or the antenna port isolation is below –20 dB and good radiation characteristics have been observed.
A TRIPLE RECTANGULAR-SLOTTED MICROSTRIP PATCH ANTENNA FOR WLAN & WIMAX APPLIC...jantjournal
ABSTRACT
A triple rectangular slotted microstrip patch antenna is designed and investigated with and without slot using CST Software. By using the triple rectangular shaped slot the designed antenna operates at 2.4GHz (ranging from 2.3704 GHz (Gigahertz) to 2.4391 GHz at -10dB return loss) for WLAN (Wireless Local Area Network) and 3.6GHz (ranging from 3.5643 GHz to 3.6548 GHz at -10dB return loss) for WiMAX (Worldwide Interoperability for Microwave Access) applications having a maximum return loss -28.5dB and -25.4dB respectively. For the design of this antenna we have chosen FR-4 (lossy) as substrate having permittivity 4.3. The designed antenna has appreciable values of gain and directivity at both the frequencies. The proposed antenna works on the principle of excitation of the slots at the operating frequencies. The antenna was designed keeping in mind the two major Wireless standards i.e., WLAN and WiMAX bands of frequencies. The proposed triple-rectangular slots are unique in terms of its construction and have appreciable results at the operating frequencies.
KEYWORDS
MSPA, Rectangular slots, Return loss, WLAN, WiMAX
Dual polarized, high-gain sector antenna for mimoprjpublications
This document summarizes the design and testing of a dual-polarized, high-gain sector antenna for MIMO communications systems. It describes the configuration of the antenna, which uses a microstrip Wilkinson power divider and L-shaped probes to feed two square patches. Simulation results are presented analyzing the effects of various structural parameters on antenna performance. Measurements of the fabricated antenna show good agreement with simulations, meeting requirements of VSWR less than 1.4 and gain over 11 dBi across the 3.35-3.65 GHz band. The antenna has advantages of dual polarization, simple structure, and potential for arraying.
The document summarizes a research paper on the design of a frequency reconfigurable monopole antenna with a switchable symmetric slot structure. The antenna is designed to operate across multiple frequency bands by using p-i-n diodes to switch the state of the symmetric slot structure on the ground plane. Five diode combinations are identified that allow the antenna to operate at different single and dual frequency bands between 1.72-9.57 GHz. The simple and compact antenna design makes it suitable for applications requiring reconfiguration across multiple frequency bands like cognitive radio and multi-radio wireless systems.
Compact Rectangular Slot Microstrip Antenna with Band-Notched Characteristics...jmicro
n this paper, we present an offset microstrip-fed ultraw
ideband antenna with band notch
characteristics.The antenna structure consists of rectangular r
adiating patch and ground plane with
rectangular shaped slot, which increases impedance bandwidth upto 1
17.73%(2.9-11.2GHz).A new
modified U slot is etched in the radiating patch to create band-
notched properties in the WiMAX (3.3-
3.7GHz) and C-band satellite communication (3.7-4.15GHz).Further
more, parametric studies have been
conducted using EM simulation software CADFEKO suite(7.0) and
optimized with stable radiation pattern
which satisfied UWB requirement for VSWR<2.A prototype of ante
nna is fabricated on 1.6mm thick FR-4
substrate with dielectric constant of 4.4 and loss tangent of 0.02
.The designed antenna exhibits
bidirectional and omni directional radiation patterns along E and
H-plane with stable gain and efficiency
over entire operating band except notch frequency band. Simulated res
ults are in good agreement with the
measured results of the proposed antenna which makes it a good
candidate for UWB application.
International Journal of Computational Engineering Research(IJCER)ijceronline
This document discusses using a triangular lattice electromagnetic bandgap (EBG) structure in the ground plane of a 2x2 triangular microstrip patch antenna array to improve its bandwidth. The EBG structure provides better antenna gain and a 110% increase in bandwidth compared to the antenna array without EBG. Keywords discussed include equilateral triangular microstrip patch antenna, antenna array, EBG, impedance bandwidth, and triangular lattice.
The document describes the design and simulation of a novel star-shaped fractal slot antenna. The antenna was modified from a triangular microstrip antenna into a star-shaped patch with fractal geometry. This increased the antenna's impedance bandwidth. Simulation results showed the antenna achieved a wide bandwidth of 56.67% from 4.8 GHz to 7.1 GHz, covering WLAN and X-band applications. Within this band, the antenna maintained stable radiation patterns and a gain ranging from 6.33 dBi to 10.02 dBi. Introducing a fractal iteration further improved the bandwidth and gain.
Design and development of triple band ominidirectional slotted rectangular mi...IAEME Publication
This document summarizes the design and development of a triple band slotted rectangular microstrip antenna (TSRMA). Key points:
- TSRMA is designed to operate over three frequency bands from 4.75-16 GHz using rectangular slots on the patch and a ground plane.
- Both simulated and experimental results show TSRMA achieves bandwidths of 260 MHz, 3.113 GHz, and 5.27 GHz across the three bands.
- Radiation patterns measured at the second and third bands were omnidirectional, as desired for applications in microwave systems.
- The simple, low-cost antenna design makes it suitable for systems operating over the 4.75-16 GHz range.
A Three-in-One Diversity Antenna System for 5 GHz WLAN ApplicationsSaou-Wen Su
A novel, three-in-one antenna system suitable for WLAN operation in the 5 GHz band is presented. The design is based upon incorporating one slot and two dipole antennas into a compact multi-antenna system that has comparable dimensions of a single mobile-unit antenna element. The three antennas are arranged parallel to each other with the two dipoles set on the right and left sides of the slot respectively. With this arrangement, not only can compact integration of three individual antennas be realized, pattern diversity and polarization diversity are also obtained. A design prototype has been constructed and tested. The results show that the coupling or the antenna port isolation is below –20 dB and good radiation characteristics have been observed.
A TRIPLE RECTANGULAR-SLOTTED MICROSTRIP PATCH ANTENNA FOR WLAN & WIMAX APPLIC...jantjournal
ABSTRACT
A triple rectangular slotted microstrip patch antenna is designed and investigated with and without slot using CST Software. By using the triple rectangular shaped slot the designed antenna operates at 2.4GHz (ranging from 2.3704 GHz (Gigahertz) to 2.4391 GHz at -10dB return loss) for WLAN (Wireless Local Area Network) and 3.6GHz (ranging from 3.5643 GHz to 3.6548 GHz at -10dB return loss) for WiMAX (Worldwide Interoperability for Microwave Access) applications having a maximum return loss -28.5dB and -25.4dB respectively. For the design of this antenna we have chosen FR-4 (lossy) as substrate having permittivity 4.3. The designed antenna has appreciable values of gain and directivity at both the frequencies. The proposed antenna works on the principle of excitation of the slots at the operating frequencies. The antenna was designed keeping in mind the two major Wireless standards i.e., WLAN and WiMAX bands of frequencies. The proposed triple-rectangular slots are unique in terms of its construction and have appreciable results at the operating frequencies.
KEYWORDS
MSPA, Rectangular slots, Return loss, WLAN, WiMAX
Radiation performance enhancement of an ultra wide band antenna using metamat...IJECEIAES
In this paper, a metamaterial structure based on frequency selective surface (FSS) cell is proposed to achieve an isotropic band-pass filtering response. This filter consists of a planar layer formed by a 3×3 metamaterials cell array with transmittive filtering behavior at 3.5 GHz. This design with 45×45 mm dimension is then integrated in close proximity at distance of 10 mm with an ultra wide band (UWB) antenna to enhance it’ s performances around a 3.5 GHz operating frequency. Simulation results ensure that filter geometry provides the advantage of the angular stability up to to 45 and also polarization modes independency (transverse electric (TE) and transverse magnetic (TM)). In addition, enhancement in antenna radiation pattern characteristics is enhanced especially when the FSS filter layer is integrated at a very close distance from the radiator. Moreover, antenna gain was improved to 3.22 dBi, adaptation of antenna port (S 11 ) was increased to -53.26 dB and antenna bandwidth reduction to 1.7 GHz is also detected. All these performances make the proposed design as a good choice used to shield signals in UWB wireless applications especially for connected object in 5G.
Dual band microstrip antenna with slit load design for wireless local area ne...BASIM AL-SHAMMARI
This paper presents a design of dual frequency band operation nearly square patch antenna
for IEEE 802.11b,g (2.4Ghz-2.4835GHz) and IEEE 802.11a (5.15GHz-5.25GHz)by using a patch
antenna. The patch and ground plane are separated by a substrate; the radiating patch have two pairs
of orthogonal slits cut from the edge, this antenna has wide bandwidth in the frequency band of
(WLAN) and with a return loss ≤ −10 dB from 2.4 GHz to 2.48 GHz and from 5.12 GHz to 5.32
GHz exhibits circularly polarized far-field radiation pattern. The proposed antennas have been
simulated and analyzed using method of moments (MoM) based software package Microwave
Office 2009 v9.0. The results show that the antenna has dual-band frequency operation by using slit
load.
Dual band microstrip antenna with slit load design for wireless local area ne...BASIM AL-SHAMMARI
This paper presents a design of dual frequency band operation nearly square patch antenna
for IEEE 802.11b,g (2.4Ghz-2.4835GHz) and IEEE 802.11a (5.15GHz-5.25GHz)by using a patch
antenna. The patch and ground plane are separated by a substrate; the radiating patch have two pairs
of orthogonal slits cut from the edge, this antenna has wide bandwidth in the frequency band of
(WLAN) and with a return loss ≤ −10 dB from 2.4 GHz to 2.48 GHz and from 5.12 GHz to 5.32
GHz exhibits circularly polarized far field radiation pattern. The proposed antennas have been
simulated and analyzed using method of moments (MoM) based software package Microwave
Office 2009 v9.0. The results show that the antenna has dual band frequency operation by using slit
load.
Microstrip patch antennas are the most common form
of printed antennas. They became very popular due to their low
profile geometry, light weight and low cost. A Rectangular
Microstrip Patch Antenna with probe feed and substrate used is
Arlon AD260 has the relative permittivity of which is 2.6 is
designed and simulated using high frequency structure simulator
(HFSS). All the Parameters of this microsrip patch Antenna such
as bandwidth, S - parameter, Reflection loss and VSWR has been
found and plotted. The main objective of this work is to consider
the reactive loading effect on the patch and its effect towards the
improvement of the antenna characteristics, particularly the
radiation characteristics in principle plane (E and H) is
examined. As per theoretical approach reactive loading creates
either capacitive loading or inductive loading. Due to this effect
the antenna performance may be degraded or enhanced in terms
of efficiency, isolation, gain, impedance matching etc. The results
of this designed antenna are compared with the existing Micro
strip antenna
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
This document summarizes research on miniaturizing a microstrip patch antenna using a novel metamaterial structure. A rectangular patch antenna was designed to resonate at 6 GHz. Then, a unit cell metamaterial composed of two nested split octagons was designed and shown to exhibit negative permeability and permittivity in a specific frequency band, behaving as a double-negative metamaterial. An array of these unit cells was placed on the patch antenna substrate. Simulation results showed the antenna's resonance frequency shifted to match the metamaterial's resonance frequency, allowing miniaturization of the antenna dimensions while maintaining performance. Both a 3x5 array and single unit cell were tested, demonstrating size reduction of the antenna for operation at 3
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna
resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different
details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different
details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna
resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different
details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This document summarizes a research paper that proposes a modified patch antenna design for dual-band operation at 3 GHz and 5 GHz. The antenna design incorporates defected ground structures and slots cut into the patch and ground planes. Simulation results show return losses of -12.17 dB at 3 GHz and -10.04 dB at 5 GHz, meeting the design goals. The antenna was fabricated and measured results matched well with simulations, validating the proposed antenna design for body-centric wireless applications.
Comparative Analysis for Different Stack Shaped Microstrip Patch Antennaijsrd.com
A compact stack antenna consisting of square patch, loop couplers and inset feed line is reviewed in this work. This proposed design represents a stacked patch antenna having an arrangement of two substrates separated by an air gape and a coupling is provided using square loop structure. The structure is reviewed in two different directions firstly the feed arrangement is varied and secondly a variation in coupler structure is done to make the antenna work at multiple frequencies in UWB range. The simulation results of this work with different resonator structure and feed structures are presented and comparative analysis of these different arrangements is presented in this paper. Simulation results obtained from the proposed antenna for return loss, polar radiation and pattern voltage standing wave ratio (VSWR) shows its suitability for ultra wide band application.
In the recent years the improvement in communication systems requires the development of low cost, minimal weight, low profile antennas that are capable of maintaining high performance over a wide spectrum of frequency. This technological trend has focused much effort into the design of a Micro strip patch antenna. In this paper, we designed a rectangular micro strip patch antenna at 3.8GHz and study the effect of antenna dimension Length (L), Width (W), substrate parameter relative dielectric constant (€r ) substrate thickness (h) and radiation pattern using Ansoft HFSS. It even describes the increasing effect of Gain and Directivity. The Proposed antenna also presents the detail steps of designing the micro strip antenna and the simulated result. The feeding technique used to feed the antenna is coaxial probe feeding technique. Micro strip patch antenna is used in many fields like Antenna and mobile communication, Filters, PCB board model and EMC and EMI. Rogers RT/duroid 5880 (tm) substrate with a dielectric constant of approximately 2.2, is a feed and has a partial ground plane. The gain and directivity of the designed antenna is 7.7082 dB and 7.76882dB respectively.
A Triple Band Bow Tie Array Antenna Using Both-sided MIC Technology IJECEIAES
A single-fed linearly polarized 2x2 microstrip bow tie array antenna is proposed. The feed network has microstrip line and slot line where microstrip-slot branch circuit is connected in parallel. The feed network of the array is designed using both-sided M IC Technology to overcome the impedance matching problem of conventional feed networks. The 2x2 half bow tie array antenna is also truncated with spur lines for optimization of antenna performance. The array antenna unit can be realized in very simple and compact structure, as all the antenna elements and the feeding circuit is arranged on a Teflon glass fiber substrate without requiring any external network. The design frequency of the proposed antenna is 5 to 8 GHz (C- Band) and the obtained peak gain is 12.41 dBi. The resultant axial ratio indicates that linear polarization is achieved.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This document summarizes a research paper that proposes a modified patch antenna design for dual-band operation at 3 GHz and 5 GHz. The antenna design incorporates slots of different sizes and a defected ground structure to achieve the dual-band functionality. Simulation results using IE3D software show return losses of -12.17 dB at 3 GHz and -10.04 dB at 5 GHz. The fabricated antenna prototype shows good agreement with the simulated results, with a measured return loss of -12.71 dB. The proposed antenna design achieves the goal of operating at two frequency bands for applications requiring body-centric wireless communication.
Generative AI Use cases applications solutions and implementation.pdfmahaffeycheryld
Generative AI solutions encompass a range of capabilities from content creation to complex problem-solving across industries. Implementing generative AI involves identifying specific business needs, developing tailored AI models using techniques like GANs and VAEs, and integrating these models into existing workflows. Data quality and continuous model refinement are crucial for effective implementation. Businesses must also consider ethical implications and ensure transparency in AI decision-making. Generative AI's implementation aims to enhance efficiency, creativity, and innovation by leveraging autonomous generation and sophisticated learning algorithms to meet diverse business challenges.
https://www.leewayhertz.com/generative-ai-use-cases-and-applications/
More Related Content
Similar to HIGH GAIN COMPACT MICROSTRIP PATCH ANTENNA FOR X-BAND APPLICATIONS
Radiation performance enhancement of an ultra wide band antenna using metamat...IJECEIAES
In this paper, a metamaterial structure based on frequency selective surface (FSS) cell is proposed to achieve an isotropic band-pass filtering response. This filter consists of a planar layer formed by a 3×3 metamaterials cell array with transmittive filtering behavior at 3.5 GHz. This design with 45×45 mm dimension is then integrated in close proximity at distance of 10 mm with an ultra wide band (UWB) antenna to enhance it’ s performances around a 3.5 GHz operating frequency. Simulation results ensure that filter geometry provides the advantage of the angular stability up to to 45 and also polarization modes independency (transverse electric (TE) and transverse magnetic (TM)). In addition, enhancement in antenna radiation pattern characteristics is enhanced especially when the FSS filter layer is integrated at a very close distance from the radiator. Moreover, antenna gain was improved to 3.22 dBi, adaptation of antenna port (S 11 ) was increased to -53.26 dB and antenna bandwidth reduction to 1.7 GHz is also detected. All these performances make the proposed design as a good choice used to shield signals in UWB wireless applications especially for connected object in 5G.
Dual band microstrip antenna with slit load design for wireless local area ne...BASIM AL-SHAMMARI
This paper presents a design of dual frequency band operation nearly square patch antenna
for IEEE 802.11b,g (2.4Ghz-2.4835GHz) and IEEE 802.11a (5.15GHz-5.25GHz)by using a patch
antenna. The patch and ground plane are separated by a substrate; the radiating patch have two pairs
of orthogonal slits cut from the edge, this antenna has wide bandwidth in the frequency band of
(WLAN) and with a return loss ≤ −10 dB from 2.4 GHz to 2.48 GHz and from 5.12 GHz to 5.32
GHz exhibits circularly polarized far-field radiation pattern. The proposed antennas have been
simulated and analyzed using method of moments (MoM) based software package Microwave
Office 2009 v9.0. The results show that the antenna has dual-band frequency operation by using slit
load.
Dual band microstrip antenna with slit load design for wireless local area ne...BASIM AL-SHAMMARI
This paper presents a design of dual frequency band operation nearly square patch antenna
for IEEE 802.11b,g (2.4Ghz-2.4835GHz) and IEEE 802.11a (5.15GHz-5.25GHz)by using a patch
antenna. The patch and ground plane are separated by a substrate; the radiating patch have two pairs
of orthogonal slits cut from the edge, this antenna has wide bandwidth in the frequency band of
(WLAN) and with a return loss ≤ −10 dB from 2.4 GHz to 2.48 GHz and from 5.12 GHz to 5.32
GHz exhibits circularly polarized far field radiation pattern. The proposed antennas have been
simulated and analyzed using method of moments (MoM) based software package Microwave
Office 2009 v9.0. The results show that the antenna has dual band frequency operation by using slit
load.
Microstrip patch antennas are the most common form
of printed antennas. They became very popular due to their low
profile geometry, light weight and low cost. A Rectangular
Microstrip Patch Antenna with probe feed and substrate used is
Arlon AD260 has the relative permittivity of which is 2.6 is
designed and simulated using high frequency structure simulator
(HFSS). All the Parameters of this microsrip patch Antenna such
as bandwidth, S - parameter, Reflection loss and VSWR has been
found and plotted. The main objective of this work is to consider
the reactive loading effect on the patch and its effect towards the
improvement of the antenna characteristics, particularly the
radiation characteristics in principle plane (E and H) is
examined. As per theoretical approach reactive loading creates
either capacitive loading or inductive loading. Due to this effect
the antenna performance may be degraded or enhanced in terms
of efficiency, isolation, gain, impedance matching etc. The results
of this designed antenna are compared with the existing Micro
strip antenna
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
This document summarizes research on miniaturizing a microstrip patch antenna using a novel metamaterial structure. A rectangular patch antenna was designed to resonate at 6 GHz. Then, a unit cell metamaterial composed of two nested split octagons was designed and shown to exhibit negative permeability and permittivity in a specific frequency band, behaving as a double-negative metamaterial. An array of these unit cells was placed on the patch antenna substrate. Simulation results showed the antenna's resonance frequency shifted to match the metamaterial's resonance frequency, allowing miniaturization of the antenna dimensions while maintaining performance. Both a 3x5 array and single unit cell were tested, demonstrating size reduction of the antenna for operation at 3
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna
resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different
details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different
details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna
resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different
details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This document summarizes a research paper that proposes a modified patch antenna design for dual-band operation at 3 GHz and 5 GHz. The antenna design incorporates defected ground structures and slots cut into the patch and ground planes. Simulation results show return losses of -12.17 dB at 3 GHz and -10.04 dB at 5 GHz, meeting the design goals. The antenna was fabricated and measured results matched well with simulations, validating the proposed antenna design for body-centric wireless applications.
Comparative Analysis for Different Stack Shaped Microstrip Patch Antennaijsrd.com
A compact stack antenna consisting of square patch, loop couplers and inset feed line is reviewed in this work. This proposed design represents a stacked patch antenna having an arrangement of two substrates separated by an air gape and a coupling is provided using square loop structure. The structure is reviewed in two different directions firstly the feed arrangement is varied and secondly a variation in coupler structure is done to make the antenna work at multiple frequencies in UWB range. The simulation results of this work with different resonator structure and feed structures are presented and comparative analysis of these different arrangements is presented in this paper. Simulation results obtained from the proposed antenna for return loss, polar radiation and pattern voltage standing wave ratio (VSWR) shows its suitability for ultra wide band application.
In the recent years the improvement in communication systems requires the development of low cost, minimal weight, low profile antennas that are capable of maintaining high performance over a wide spectrum of frequency. This technological trend has focused much effort into the design of a Micro strip patch antenna. In this paper, we designed a rectangular micro strip patch antenna at 3.8GHz and study the effect of antenna dimension Length (L), Width (W), substrate parameter relative dielectric constant (€r ) substrate thickness (h) and radiation pattern using Ansoft HFSS. It even describes the increasing effect of Gain and Directivity. The Proposed antenna also presents the detail steps of designing the micro strip antenna and the simulated result. The feeding technique used to feed the antenna is coaxial probe feeding technique. Micro strip patch antenna is used in many fields like Antenna and mobile communication, Filters, PCB board model and EMC and EMI. Rogers RT/duroid 5880 (tm) substrate with a dielectric constant of approximately 2.2, is a feed and has a partial ground plane. The gain and directivity of the designed antenna is 7.7082 dB and 7.76882dB respectively.
A Triple Band Bow Tie Array Antenna Using Both-sided MIC Technology IJECEIAES
A single-fed linearly polarized 2x2 microstrip bow tie array antenna is proposed. The feed network has microstrip line and slot line where microstrip-slot branch circuit is connected in parallel. The feed network of the array is designed using both-sided M IC Technology to overcome the impedance matching problem of conventional feed networks. The 2x2 half bow tie array antenna is also truncated with spur lines for optimization of antenna performance. The array antenna unit can be realized in very simple and compact structure, as all the antenna elements and the feeding circuit is arranged on a Teflon glass fiber substrate without requiring any external network. The design frequency of the proposed antenna is 5 to 8 GHz (C- Band) and the obtained peak gain is 12.41 dBi. The resultant axial ratio indicates that linear polarization is achieved.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This paper presents modified patch antenna for 3 GHz and 5 GHz operating frequencies. Here different approaches are studied by varying slot sizes, defected ground size, notch and also changing feed position. Insertion of slots gives dual frequency operation. Notch provides shifting of lower frequency band towards left hand side. Here combined effect of each techniques adopted gives desired result. Proposed antenna resonates for 3 and 5 GHz frequency. Simulation is done using IE3D software for various parameters. Return loss of final design was -12.17 dB for 3 GHz frequency and VSWR of 1.65. For 5 GHz simulation response was -10.04dB return loss and VSWR of 1.91. Proposed antenna is fabricated giving different details. Paper gives good agreement between measured and simulated results.
BODY ANTENNA WITH DGS FOR BODY CENTRIC WIRELESS COMMUNICATION SYSTEMjantjournal
This document summarizes a research paper that proposes a modified patch antenna design for dual-band operation at 3 GHz and 5 GHz. The antenna design incorporates slots of different sizes and a defected ground structure to achieve the dual-band functionality. Simulation results using IE3D software show return losses of -12.17 dB at 3 GHz and -10.04 dB at 5 GHz. The fabricated antenna prototype shows good agreement with the simulated results, with a measured return loss of -12.71 dB. The proposed antenna design achieves the goal of operating at two frequency bands for applications requiring body-centric wireless communication.
Similar to HIGH GAIN COMPACT MICROSTRIP PATCH ANTENNA FOR X-BAND APPLICATIONS (20)
Generative AI Use cases applications solutions and implementation.pdfmahaffeycheryld
Generative AI solutions encompass a range of capabilities from content creation to complex problem-solving across industries. Implementing generative AI involves identifying specific business needs, developing tailored AI models using techniques like GANs and VAEs, and integrating these models into existing workflows. Data quality and continuous model refinement are crucial for effective implementation. Businesses must also consider ethical implications and ensure transparency in AI decision-making. Generative AI's implementation aims to enhance efficiency, creativity, and innovation by leveraging autonomous generation and sophisticated learning algorithms to meet diverse business challenges.
https://www.leewayhertz.com/generative-ai-use-cases-and-applications/
Build the Next Generation of Apps with the Einstein 1 Platform.
Rejoignez Philippe Ozil pour une session de workshops qui vous guidera à travers les détails de la plateforme Einstein 1, l'importance des données pour la création d'applications d'intelligence artificielle et les différents outils et technologies que Salesforce propose pour vous apporter tous les bénéfices de l'IA.
Comparative analysis between traditional aquaponics and reconstructed aquapon...bijceesjournal
The aquaponic system of planting is a method that does not require soil usage. It is a method that only needs water, fish, lava rocks (a substitute for soil), and plants. Aquaponic systems are sustainable and environmentally friendly. Its use not only helps to plant in small spaces but also helps reduce artificial chemical use and minimizes excess water use, as aquaponics consumes 90% less water than soil-based gardening. The study applied a descriptive and experimental design to assess and compare conventional and reconstructed aquaponic methods for reproducing tomatoes. The researchers created an observation checklist to determine the significant factors of the study. The study aims to determine the significant difference between traditional aquaponics and reconstructed aquaponics systems propagating tomatoes in terms of height, weight, girth, and number of fruits. The reconstructed aquaponics system’s higher growth yield results in a much more nourished crop than the traditional aquaponics system. It is superior in its number of fruits, height, weight, and girth measurement. Moreover, the reconstructed aquaponics system is proven to eliminate all the hindrances present in the traditional aquaponics system, which are overcrowding of fish, algae growth, pest problems, contaminated water, and dead fish.
Optimizing Gradle Builds - Gradle DPE Tour Berlin 2024Sinan KOZAK
Sinan from the Delivery Hero mobile infrastructure engineering team shares a deep dive into performance acceleration with Gradle build cache optimizations. Sinan shares their journey into solving complex build-cache problems that affect Gradle builds. By understanding the challenges and solutions found in our journey, we aim to demonstrate the possibilities for faster builds. The case study reveals how overlapping outputs and cache misconfigurations led to significant increases in build times, especially as the project scaled up with numerous modules using Paparazzi tests. The journey from diagnosing to defeating cache issues offers invaluable lessons on maintaining cache integrity without sacrificing functionality.
Digital Twins Computer Networking Paper Presentation.pptxaryanpankaj78
A Digital Twin in computer networking is a virtual representation of a physical network, used to simulate, analyze, and optimize network performance and reliability. It leverages real-time data to enhance network management, predict issues, and improve decision-making processes.
Discover the latest insights on Data Driven Maintenance with our comprehensive webinar presentation. Learn about traditional maintenance challenges, the right approach to utilizing data, and the benefits of adopting a Data Driven Maintenance strategy. Explore real-world examples, industry best practices, and innovative solutions like FMECA and the D3M model. This presentation, led by expert Jules Oudmans, is essential for asset owners looking to optimize their maintenance processes and leverage digital technologies for improved efficiency and performance. Download now to stay ahead in the evolving maintenance landscape.
Rainfall intensity duration frequency curve statistical analysis and modeling...bijceesjournal
Using data from 41 years in Patna’ India’ the study’s goal is to analyze the trends of how often it rains on a weekly, seasonal, and annual basis (1981−2020). First, utilizing the intensity-duration-frequency (IDF) curve and the relationship by statistically analyzing rainfall’ the historical rainfall data set for Patna’ India’ during a 41 year period (1981−2020), was evaluated for its quality. Changes in the hydrologic cycle as a result of increased greenhouse gas emissions are expected to induce variations in the intensity, length, and frequency of precipitation events. One strategy to lessen vulnerability is to quantify probable changes and adapt to them. Techniques such as log-normal, normal, and Gumbel are used (EV-I). Distributions were created with durations of 1, 2, 3, 6, and 24 h and return times of 2, 5, 10, 25, and 100 years. There were also mathematical correlations discovered between rainfall and recurrence interval.
Findings: Based on findings, the Gumbel approach produced the highest intensity values, whereas the other approaches produced values that were close to each other. The data indicates that 461.9 mm of rain fell during the monsoon season’s 301st week. However, it was found that the 29th week had the greatest average rainfall, 92.6 mm. With 952.6 mm on average, the monsoon season saw the highest rainfall. Calculations revealed that the yearly rainfall averaged 1171.1 mm. Using Weibull’s method, the study was subsequently expanded to examine rainfall distribution at different recurrence intervals of 2, 5, 10, and 25 years. Rainfall and recurrence interval mathematical correlations were also developed. Further regression analysis revealed that short wave irrigation, wind direction, wind speed, pressure, relative humidity, and temperature all had a substantial influence on rainfall.
Originality and value: The results of the rainfall IDF curves can provide useful information to policymakers in making appropriate decisions in managing and minimizing floods in the study area.
VARIABLE FREQUENCY DRIVE. VFDs are widely used in industrial applications for...PIMR BHOPAL
Variable frequency drive .A Variable Frequency Drive (VFD) is an electronic device used to control the speed and torque of an electric motor by varying the frequency and voltage of its power supply. VFDs are widely used in industrial applications for motor control, providing significant energy savings and precise motor operation.
Advanced control scheme of doubly fed induction generator for wind turbine us...IJECEIAES
This paper describes a speed control device for generating electrical energy on an electricity network based on the doubly fed induction generator (DFIG) used for wind power conversion systems. At first, a double-fed induction generator model was constructed. A control law is formulated to govern the flow of energy between the stator of a DFIG and the energy network using three types of controllers: proportional integral (PI), sliding mode controller (SMC) and second order sliding mode controller (SOSMC). Their different results in terms of power reference tracking, reaction to unexpected speed fluctuations, sensitivity to perturbations, and resilience against machine parameter alterations are compared. MATLAB/Simulink was used to conduct the simulations for the preceding study. Multiple simulations have shown very satisfying results, and the investigations demonstrate the efficacy and power-enhancing capabilities of the suggested control system.
Applications of artificial Intelligence in Mechanical Engineering.pdfAtif Razi
Historically, mechanical engineering has relied heavily on human expertise and empirical methods to solve complex problems. With the introduction of computer-aided design (CAD) and finite element analysis (FEA), the field took its first steps towards digitization. These tools allowed engineers to simulate and analyze mechanical systems with greater accuracy and efficiency. However, the sheer volume of data generated by modern engineering systems and the increasing complexity of these systems have necessitated more advanced analytical tools, paving the way for AI.
AI offers the capability to process vast amounts of data, identify patterns, and make predictions with a level of speed and accuracy unattainable by traditional methods. This has profound implications for mechanical engineering, enabling more efficient design processes, predictive maintenance strategies, and optimized manufacturing operations. AI-driven tools can learn from historical data, adapt to new information, and continuously improve their performance, making them invaluable in tackling the multifaceted challenges of modern mechanical engineering.
Software Engineering and Project Management - Introduction, Modeling Concepts...Prakhyath Rai
Introduction, Modeling Concepts and Class Modeling: What is Object orientation? What is OO development? OO Themes; Evidence for usefulness of OO development; OO modeling history. Modeling
as Design technique: Modeling, abstraction, The Three models. Class Modeling: Object and Class Concept, Link and associations concepts, Generalization and Inheritance, A sample class model, Navigation of class models, and UML diagrams
Building the Analysis Models: Requirement Analysis, Analysis Model Approaches, Data modeling Concepts, Object Oriented Analysis, Scenario-Based Modeling, Flow-Oriented Modeling, class Based Modeling, Creating a Behavioral Model.
2008 BUILDING CONSTRUCTION Illustrated - Ching Chapter 02 The Building.pdf
HIGH GAIN COMPACT MICROSTRIP PATCH ANTENNA FOR X-BAND APPLICATIONS
1. International Journal of Antennas (JANT) Vol.2, No.1, January 2016
DOI: 10.5121/jant.2016.2105 47
HIGH GAIN COMPACT MICROSTRIP PATCH
ANTENNA FOR X-BAND APPLICATIONS
1
Mohamed AlyAboul-Dahab, 2
Hussein Hamed Mahmoud Ghouz and 3
Ahmed
Zakaria Ahmed Zaki
1,2
Professors in Department of Electronics and Communications
Arab Academy for Science, Technology & Maritime Transport (AASTMT), Cairo, Egypt
3
Master students in Arab Academy for Science, (AASTMT), Cairo, Egypt
ABSTRACT
This paper present a design of a Frequency Selective Surface (FSS) to improve gain and efficiency of a
microstrip patch antenna operating in X-band at 10 GHz. The band-stop frequency selective surface (FSS)
designed at the operating frequency of the antenna is used. FSS structure is configured as a superstrate for
the microstrip patch antenna. The main goal of this paper is design a compact microstrip antenna module
(microstrip patch and FSS structure). Simulation results using CST studio showed that high gain (54 %
increment) and efficiency is increased to 97% have been achieved by the proposed antenna module (MS
and FSS). The equivalent circuit of proposed FSS unit cell in ADS software has been evaluated and
compared to simulation results (CST studio) to improve characteristics of the antenna. The proposed
antenna module is extremely compact high gain and it can be used for X-band applications.
KEYWORDS
Compact; microstrip; frequency selective surface; X-band.
1. INTRODUCTION
In recent years, the demand for high gain antennas has increased for use in high-frequency and
high-speed data communication. Microstrip patch antenna characterized by attractive features
such as low cost and compact size, but the important problems of patch antenna are its small gain,
law directivity and narrow bandwidth because of substrate dielectric has surface wave losses [1,
2], so to improve the gain and directivity became an important issue in the antenna design field.
Improving bandwidth, gain and directivity can obtained by an antenna with periodic elements
(FSS) [3-8]. Frequency selective surface (FSS) is a 2D planar structure consisting of a two-
dimensional array of slot elements in a metal sheet or an array of metal patch elements fabricated
on dielectric substrate. The frequency response of FSS is determined by the shape and size of the
structure in one period called a unit cell [9]. Aperture and patch screens generally give
complementary frequency responses, the field is totally transmitted at the resonant frequency of
the aperture while a screen comprised of patches will be nearly totally reflected at the resonant
frequency of the patches [10]. Frequency selective surfaces (FSSs) have been investigated for a
variety of applications such as bandpass and bandstop spatial filter [11-14], radar absorbers [15-
17], and artificial electromagnetic bandgap materials [18]. It can also be used as Specific
Absorption Rate (SAR) [19].
In this paper, the single band frequency FSS consisting of hexagonal loop elements is used to
enhance gain and efficiency of proposed compact rectangular microstrip antenna operating at 10
GHz. However, the design of such complex structure of FSS is not easy matter due to many
2. International Journal of Antennas (JANT) Vol.2, No.1, January 2016
design parameters that require
discuss antenna and frequency selective surface (FSS) designs. Section 3 shows result
discussion which include a parametric study of FSS cell and effect of implanting FSS to antenna.
Implementation and Experimental testing of FSS and antenna is discussed in Se
by conclusion in Section 5.
2. ANTENNA AND PROPOSED FREQUEN
SURFACE DESIGN
2.1 Proposed Antenna
Proposed antenna is a conventional rectangular microstrip antenna which designed to operate at
10 GHz in X-band. As shown in figures [1]
thickness ROGGER 5880 substrate with dielectric constan
of 40mm X 40mm and thickness of 0.035 mm is used as the ground plane. The patch uses copper
as material and the thickness of it is 0.035 mm, the patch is symmetrically designed an
point lies in the central line of 3.4 mm
is used as the feed of the conventional patch antenna. The inner conductor of the coaxial line is
attached on the top patch going through the die
to the metallic plate on the other side of the patch antenna.
equations [1, 2] as shown in table
(a)
Figure 1:
Table 1. Proposed antenna parameters
Patch
Wp (mm)
Lp (mm)
Tp(mm)
material
International Journal of Antennas (JANT) Vol.2, No.1, January 2016
that require optimized. This paper is divided into five sections. Section 2
discuss antenna and frequency selective surface (FSS) designs. Section 3 shows result
discussion which include a parametric study of FSS cell and effect of implanting FSS to antenna.
Implementation and Experimental testing of FSS and antenna is discussed in Section
2. ANTENNA AND PROPOSED FREQUENCY SELECTIVE
SURFACE DESIGN
Proposed antenna is a conventional rectangular microstrip antenna which designed to operate at
As shown in figures [1], the rectangular patch antenna is printed on 1.5
substrate with dielectric constant 2.2. A copper plate with dimensions
40mm and thickness of 0.035 mm is used as the ground plane. The patch uses copper
as material and the thickness of it is 0.035 mm, the patch is symmetrically designed an
point lies in the central line of 3.4 mm, a coaxial line with a characteristic impedance of 50 ohms
is used as the feed of the conventional patch antenna. The inner conductor of the coaxial line is
attached on the top patch going through the dielectric substrate, and the outer conductor is shorted
to the metallic plate on the other side of the patch antenna. All dimensions evaluated by using
] as shown in table 1.
(b)
Figure 1: Antenna (a) Top view (b) Side view
Proposed antenna parameters (MILLEMETER)
Patch Substrate
11.85 Ws (mm) 40
9.13 Ls (mm) 40
0.035 Ts(mm) 1.575
Copper material Roger (εr = 2.2)
48
This paper is divided into five sections. Section 2
discuss antenna and frequency selective surface (FSS) designs. Section 3 shows result and
discussion which include a parametric study of FSS cell and effect of implanting FSS to antenna.
ction 4 followed
CY SELECTIVE
Proposed antenna is a conventional rectangular microstrip antenna which designed to operate at
he rectangular patch antenna is printed on 1.575 mm
copper plate with dimensions
40mm and thickness of 0.035 mm is used as the ground plane. The patch uses copper
as material and the thickness of it is 0.035 mm, the patch is symmetrically designed and the feed
, a coaxial line with a characteristic impedance of 50 ohms
is used as the feed of the conventional patch antenna. The inner conductor of the coaxial line is
lectric substrate, and the outer conductor is shorted
All dimensions evaluated by using
3. International Journal of Antennas (JANT) Vol.2, No.1, January 2016
2.2 Proposed FSS unit cell
The proposed cell is a 0.035 mm copper
mm thickness ROGGER substrate with dielectric constant is 2.2 as shown in figure
as passive electromagnetic filters
the gain, efficiency and resonant frequency of the
by shape and dimension of the unit cell
bandwidth and resonance of FSS. Detail dimensions of the hexagonal loops ring element are
evaluated as shown in table 2.
Table
FSS cells (truncated edge) printed on 40mm X 40mm Rogg
FSS structure is placed on top of the proposed rectangular patch antenna
the FSS layer placed at separation (H) is
size of the antenna.
International Journal of Antennas (JANT) Vol.2, No.1, January 2016
0.035 mm copper hexagonal-loop was designed and fabricated
mm thickness ROGGER substrate with dielectric constant is 2.2 as shown in figure
as passive electromagnetic filters and it selectively reflecting a desired frequency band
the gain, efficiency and resonant frequency of the patch antenna. The FSS response is determined
the unit cell, in addition to the permittivity of substrate can control t
bandwidth and resonance of FSS. Detail dimensions of the hexagonal loops ring element are
Table 2. FSS unit cell parameters (mm)
Figure 2: structure of proposed
FSS cells (truncated edge) printed on 40mm X 40mm Rogger substrate as shown in figure 3(a)
FSS structure is placed on top of the proposed rectangular patch antenna as shown in figure.
separation (H) is one over twenty of wavelengths to validate the compact
Symbol mm
A 9.7
B 8
C 0.8
D 1.3
E 4
F 19
G 22
49
was designed and fabricated on 1.575
mm thickness ROGGER substrate with dielectric constant is 2.2 as shown in figure 2. It behave
selectively reflecting a desired frequency band to improve
response is determined
of substrate can control the
bandwidth and resonance of FSS. Detail dimensions of the hexagonal loops ring element are
er substrate as shown in figure 3(a).
as shown in figure.5,
e over twenty of wavelengths to validate the compact
4. International Journal of Antennas (JANT) Vol.2, No.1, January 2016
(a) (b)
Figure 3: (a) proposed FSS Cells (b) structure of proposed antenna module
3. RESULTS AND DISCUSSION
In this section, a proposed FSS unit
simulated using the CST-MW simulator.
consists of Microwave Studio, EM Studio, PCB Studio, etc. We focus on the Microwave Studio
which employs the Finite Difference Time Domain Method. The method is based on the time
domain and can cover a wide frequency band with one single simulation run. It is also quick and
suitable for non-uniform models. However, results from CST do not closely fit for configurations
with a large range of dimensions, such as a half wavelength dipole using an impractically thi
wire for example. This is because of CST’s sensitivity to extremely small mesh grid settings.
parametric study of FSS unit cell have been investigated as shown in figures [4], [5], and [6].
3.1 UNITE CELL SIMULATION AND RESULTS
Fig.4 shows the effect of changing modes on transmission and reflection coefficient
characteristics of the proposed FSS unit cell. It is a band stop filter and it rejects wide band from
4 GHz to 14GHZ with center frequency 10GHz at TE and TM mode.
International Journal of Antennas (JANT) Vol.2, No.1, January 2016
(a) (b)
Figure 3: (a) proposed FSS Cells (b) structure of proposed antenna module
3. RESULTS AND DISCUSSION
unit cell and the microstrip patch antenna, have been analyzed and
MW simulator. CST stands for Computer Simulation Technology and
consists of Microwave Studio, EM Studio, PCB Studio, etc. We focus on the Microwave Studio
which employs the Finite Difference Time Domain Method. The method is based on the time
equency band with one single simulation run. It is also quick and
uniform models. However, results from CST do not closely fit for configurations
with a large range of dimensions, such as a half wavelength dipole using an impractically thi
wire for example. This is because of CST’s sensitivity to extremely small mesh grid settings.
parametric study of FSS unit cell have been investigated as shown in figures [4], [5], and [6].
3.1 UNITE CELL SIMULATION AND RESULTS
of changing modes on transmission and reflection coefficient
characteristics of the proposed FSS unit cell. It is a band stop filter and it rejects wide band from
4 GHz to 14GHZ with center frequency 10GHz at TE and TM mode.
50
Figure 3: (a) proposed FSS Cells (b) structure of proposed antenna module
, have been analyzed and
stands for Computer Simulation Technology and
consists of Microwave Studio, EM Studio, PCB Studio, etc. We focus on the Microwave Studio
which employs the Finite Difference Time Domain Method. The method is based on the time
equency band with one single simulation run. It is also quick and
uniform models. However, results from CST do not closely fit for configurations
with a large range of dimensions, such as a half wavelength dipole using an impractically thin
wire for example. This is because of CST’s sensitivity to extremely small mesh grid settings. A
parametric study of FSS unit cell have been investigated as shown in figures [4], [5], and [6].
of changing modes on transmission and reflection coefficient
characteristics of the proposed FSS unit cell. It is a band stop filter and it rejects wide band from
5. International Journal of Antennas (JANT) Vol.2, No.1, January 2016
(a)
Figure 4: response of proposed unite cell in (a) TE mode and (b) TM mode.
The equivalent circuit of the proposed FSS unit cell with characteristic impedance Z is shown in
Fig.5(a).The introduced capacitances represent the gap between conductors in the FSS unit
while the inductance represents the metallic parts forming the hexagonal loop shape.
International Journal of Antennas (JANT) Vol.2, No.1, January 2016
(b)
response of proposed unite cell in (a) TE mode and (b) TM mode.
The equivalent circuit of the proposed FSS unit cell with characteristic impedance Z is shown in
apacitances represent the gap between conductors in the FSS unit
while the inductance represents the metallic parts forming the hexagonal loop shape.
51
The equivalent circuit of the proposed FSS unit cell with characteristic impedance Z is shown in
apacitances represent the gap between conductors in the FSS unit-cell,
while the inductance represents the metallic parts forming the hexagonal loop shape.
6. International Journal of Antennas (JANT) Vol.2, No.1, January 2016
52
(a) (b)
Figure 5: (a) equivalent circuit of proposed cell (b) frequency response of proposed cell and its equivalent
circuit of unit cell.
For a proposed FSS unit cell geometry, an equivalent circuit (inductance and capacitance values)
investigated. C1=C2=0. 49 pF and L1= 0.51 nH L2=0. 8 nH ,by changing the values of the
inductances and capacitances, the resonance frequency is changed. Fig.5(b) shows the reflection
and transmission characteristics of the equivalent circuit of proposed unit cell using ADS
Software, two curves (proposed and its equivalent circuit) are almost identical. The filtering
operation is affected by different parameter values such as spacing between loops (D), thickness
of conductor (C) of geometry and type of substrate material (εr).
Figure 6: Effect of the changing conductor thickness “C” on the proposed FSS on the transmission
coefficient.
Thickness of conductor has an important effect on the resonance of unit cell as shown in figure 6,
as the thickness of conductor increase, the resonance frequency shifted toward higher frequency.
7. International Journal of Antennas (JANT) Vol.2, No.1, January 2016
53
Figure 7: Effect of the changing spacing “D” on the proposed FSS on the transmission coefficient.
Figure.7 shows that the effect of changing space between loops each other, by increase the space
“D” the frequency response shifted toward higher frequencies but bandwidth decrease.
Bandwidth at “D” equal 1.3mm is 5 GHz and at “D” equal 0.325mm bandwidth is 6.5 GHz.
Figure 8: Effect of changing permittivity of the proposed FSS on the transmission coefficient.
The resonance frequency of the stop-band filter is also affected by the relative permittivity of the
substrate. As illustrated in Figure 8, by increasing the substrate permittivity, the resonance
frequency shifted to lower frequency that is allowed to operate at lower frequencies with the same
compact size of FSS.
8. International Journal of Antennas (JANT) Vol.2, No.1, January 2016
54
Figure 9: Transmission coefficients of FSS cell at D = 0.325mm, C = 0.4mm and eps=6.15
As shown in figure 9, the smallest values of conductor thickness “C” and spacing “D” and the
highest permittivity have been used, so the frequency has been shifted to lowest value with the
same compact size of FSS.
3.2 Antenna and FSS simulation and results
In this section, antenna implanted with and without FSS have been discussed. Figure.10 shows
the return loss of antenna without FSS and with FSS at H=1. 5 mm (separation between antenna
and FSS), returned loss of antenna increase to -16 dB and gain reached to 9.7 which has been
improved by 48% and efficiency enhanced to reach 97% Final antenna results are listed in Table.
3
Figure 10: Return loss of antenna without FSS and with FSS at distance H=1. 5 mm
9. International Journal of Antennas (JANT) Vol.2, No.1, January 2016
55
Table.3 final result of compact microstrip antenna
Figure.11 shows effect of changing the separation (H) between antenna and FSS, at distance H=0.
375mm a new resonance frequency appeared at 9.6GHz, 8GHz and 6.9GHz. At separation
H=1.5mm only one resonance frequency appear at 10GHz, so by decreasing separation between
antenna and FSS that allow an antenna to resonate at new frequencies.
Figure 11: Effect of changing separation between antenna and FSS
(a) (b)
Figure12: Radiation patterns (a) E and (b) H planes
Without FSS With FSS
Fr (GHz) 10 10
S11 (dB) -12 -16
BW (MHz) 600 250
Rad. Efficiency (%) 94.3 97
Gain (dB) 6.2 9.7
10. International Journal of Antennas (JANT) Vol.2, No.1, January 2016
(a)
Figure 13: 3D Farfield pattern of antenna (a) without FSS and (b) with FSS
Fig. 12, 13 shows the radiation patterns of antenna
(10 GHz). The maximum gains levels have an obvious enhancement for the two main planes,
along with an increase in the gains relative to that of the initial patch antenna. Before implanting
FSS to MS antenna, the pattern was directiv
FSS to antenna pattern shape has been changed.
became multi-beam which it allowed to use antenna module in many applications such as
scanning array.
4. EXPERIMENTAL VERIFICATION
The proposed antenna and FSS ha
thicknessas shown in Fig.14, and S11 of antenna with and without FSS have been measured and
compared to the simulated results as presented in
Figure 15 shows the comparison between simulated and measur
FSS. It is noticed that the measured and simulated resonance frequencies
identical. Figure 16 shows that a good agreement has
simulated results and it is clear
identical.
(a)
Figure.14 The prototype
International Journal of Antennas (JANT) Vol.2, No.1, January 2016
(b)
3D Farfield pattern of antenna (a) without FSS and (b) with FSS
shows the radiation patterns of antenna with and without FSS at operating frequency
(10 GHz). The maximum gains levels have an obvious enhancement for the two main planes,
along with an increase in the gains relative to that of the initial patch antenna. Before implanting
FSS to MS antenna, the pattern was directive with a main loop at 90 degrees. After implanting
pattern shape has been changed. The pattern has been reshaped by FSS and it
beam which it allowed to use antenna module in many applications such as
NTAL VERIFICATION
and FSS have been fabricated on an Rogger 5880 substrate
as shown in Fig.14, and S11 of antenna with and without FSS have been measured and
compared to the simulated results as presented in Fig. 15 and Fig. 16
Figure 15 shows the comparison between simulated and measured S11 for antenna only
measured and simulated resonance frequencies are approximately
that a good agreement has been achieved between measured and
clear that the measured and simulated resonance frequencies are
(b)
The prototype of (a) patch antenna and (b) FSS and (c) antenna module
56
at operating frequency
(10 GHz). The maximum gains levels have an obvious enhancement for the two main planes,
along with an increase in the gains relative to that of the initial patch antenna. Before implanting
e with a main loop at 90 degrees. After implanting
he pattern has been reshaped by FSS and it
beam which it allowed to use antenna module in many applications such as
been fabricated on an Rogger 5880 substrate with 1.575
as shown in Fig.14, and S11 of antenna with and without FSS have been measured and
antenna only without
approximately
been achieved between measured and
measured and simulated resonance frequencies are
(c)
) FSS and (c) antenna module.
11. International Journal of Antennas (JANT) Vol.2, No.1, January 2016
57
Figure.15 antenna without FSS simulation and Measured
Figur3.16 antenna with FSS simulation and Measured
5. CONCLUSION
In this paper, high gain microstrip antenna is presented. From simulation results, it is found that
the proposed FSS structure can be used as a stop band filter. The proposed FSS has been then
applied as a superstrate to a conventional patch antenna to improve its gain and efficiency. The
antenna and FSS has been implemented and tested. The measured return losses is in a reasonable
agreement with the simulated results. The gain have been improved up to 9.2 dB (48% increment)
and efficiency increased to 97% at the operating frequency of 10 GHz. The radiation patterns at
frequency 10 GHz is acceptable. With these characteristics. The proposed antenna module
(antenna and FSS) could be used in X-band applications.
REFERENCES
[1] Ramesh Garg, P.bahrtia “ Microstrip Antenna Design Handbook” , Artech House, London, 2000
[2] Constantine A. Balanis., “Antenna Theory: Analysis and Design”, Wiley-Interscience, New York,
2005
[3] K. Pengthaisong, P. Krachodnok, and R. Wongsan, “Design of a Dual-band Antenna using a Patch
and Frequency Selective Surface for WLAN and WiMAX, “(ECTI-CON), International Conference.
Krabi ,2013 .
[4] S. Chaimool, K. L. Chung and P. Akkaraekthalin “SIMULTANEOUS GAIN AND BANDWIDTHS
ENHANCEMENT OF A SINGLE-FEED CIRCULARLY POLARIZED MICROSTRIP PATCH
ANTENNA USING A METAMATERIAL REFLECTIVE SURFACE” , Progress In
Electromagnetics Research B, Vol. 22, 23-37, 2010.
12. International Journal of Antennas (JANT) Vol.2, No.1, January 2016
58
[5] Karishma Sharma, Swati Vaid, and Ashok Mittal “An Investigation on High-Gain Dual-Polarized
Cavity Reflex Antenna Using Slotted-Patch FSS Superstrate” 4th ICCCNT, Tiruchengode, India, July
2013.
[6] Aqeel H. Naqvi, Farooq A. Tahir “A Super Wideband printed antenna with enhanced gain using FSS
structure “International Bhurban Conference on Applied Sciences & Technology (IBCAST)
Islamabad, Pakistan, 13th - 17th January, 2015.
[7] R.V.S. Ram Krishna and R. Kumar “Slotted ground microstrip antenna with FSS reflector for high-
gain horizontal polarization” ELECTRONICS LETTERS, Vol. 51 No. 8, 16th April 2015.
[8] Chen, H.-Y. and Y. Tao, “Bandwidth enhancement of a U-slot patch antenna using dual-band
frequency-selective surface with double rectangular ring elements," Microwave Opt. Technol. Lett.,
Vol. 53, No. 7, Jul. 2011.
[9] Munk, A., “Frequency Selective Surfaces: Theory and Design”, Wiley-Interscience, New York, 2000.
[10] Constantine A. Balanis., “MODERN ANTENNA HANDBOOK”, Wiley-Interscience, New York,
2008.
[11] Da Silva, M. R., C. de L. N obrega, P. H. da F. Silva, and A. G. D'Assuncao, “Dual-polarized band-
stop fss spatial filters using vicsek fractal geometry," Microwave Opt. Technol. Lett., Vol. 55, No. 1,
Jan. 2013.
[12] H.Ghorbaninejad-Foumani and M.Khalaj-Amirhosseini, “COMPACT SPATIAL BAND-PASS
FILTERS USING FREQUENCY SELECTIVE SURFACES” Progress in Electromagnetics Research
C, Vol. 21, 2011.
[13] Sanjeev Yadav, Bhavana Peswani, Vandana Jain and M.M.Sharma “A Novel Miniaturized Compact
Frequency Selective Surface Structure with Stable Resonance Characteristics ” (ICSPCT), 2014
International Conference, Ajmer , July 2014.
[14] M.R. Silva, C. L. Nóbrega, P. H.F. Silva, A. D. Assunção” Stable and compact multiband frequency
selective surfaces with Peano pre-fractal configurations” IET Microwaves, Antennas & Propagation,
vol.7, 2013.
[15] R. Panwar, S. Puthucheri, V. Agarwala and D. Sing “Effect of Particle Size on Radar Wave
Absorption of Fractal Frequency Selective Surface Loaded Multilayered Structures” IEEE
International Microwave and RF Conference (IMaRC), Bangalore, Dec. 2014.
[16] Alireza Kazem Zadeh and Anders Karlsson “Capacitive Circuit Method for Fast and Efficient Design
of Wideband Radar Absorbers” IEEE TRANSACTIONS ON ANTENNAS AND PROPAGATION,
VOL. 57, NO. 8, AUGUST 2009
[17] F. Wang, W. Jiang, T. Hong, H. Xue, S. Gong and Y. Zhang “Radar cross section reduction of
wideband antenna with a novel wideband radar absorbing materials ” IET Microwaves, Antennas &
Propagation, , Vol. 8, Iss. 7, 2014.
[18] Arnaud, E., R. Chantalat, M. Koubeissi, T. Monediere, E. Rodes, and M. Thevenot, “Global design of
an EBG antenna and meander-line polarizer for circular polarization," IEEE Antennas and Wireless
Propagation Letters, Vol. 9, 215-218, 2011.
[19] Lin, H.-N., K.-W. Lin, and S.-C. Chen, “Use of frequency selective surfaces to prevent SAR and
improve antenna performance of cellular phones," PIERS Proceedings”,Sep, 2011.