GPS INTERFACE IN GSM NETWORK
•Download as DOCX, PDF•
3 likes•876 views
This document is a seminar report submitted by Anup Kumar, roll number 125120, for the degree of Bachelor of Technology in Electrical Engineering at Orissa Engineering College in Bhubaneswar, India. The report is about integrating GPS interfaces into GSM networks and was prepared under the guidance of Er. Debashish Mishra to fulfill degree requirements.
Report
Share
Report
Share
Recommended
Cables and Connectors
This document discusses cables and connectors used in audio applications. It covers the different types of cables including straight pair, twisted pair, coaxial, and fiber optic cables. Straight pair cables are used to power speakers while microphone cables use XLR or D-sub connectors. Coaxial cables transmit digital audio signals. The document also discusses balanced and unbalanced signals, various audio connectors, and applications of different cables and connectors in audio systems.
1.government college of engineering
This seminar report discusses flexible electronics. It begins with an introduction to flexible electronics, including a brief history. It then describes flexible circuit structures and components such as resistors, capacitors, batteries, and displays. The report outlines the manufacturing process for flexible electronics using thin film transistors. Finally, it discusses the future scope and applications of flexible electronics, highlighting growth in markets. Potential applications include wearable devices, cell phones, and military/space uses. Both advantages like flexibility and disadvantages like high costs are noted.
2.1.3short Circuit
A short circuit occurs when a current travels along an unintended path with low resistance, allowing excessive current to flow. This can damage electrical equipment by overheating wires or melting insulation. Proper protective devices like fuses or circuit breakers are installed to detect abnormal currents and disconnect power before damage occurs.
WIRELESS POWER TRANSMISSION
THIS PPT IS BASED ON THE WIRELESS POWER TRANSMISSION AND THIS PPT IS MAINLY BASED ON THE UPCOMING WIRELESS TRANSMISSION IN THE CHARGING OF VEHICLES AND MOBILE PHONES THROUGH THE UPCOMING TECHNOLOGY IN THE POWER TRANSMISSION AND THIS IS SO HELP FULL TO THE ELECTRICAL AND ELECTRONICS ENGINEERING STUDENTS
Unit 4 ac voltage controller
This document was prepared by Meraj Akhtar of the Electrical Department at Jahangirabad Institute of Technology in Barabanki, Uttar Pradesh, India. It discusses electrical topics related to Meraj Akhtar's work in the Electrical Department at the Jahangirabad Institute of Technology.
Unit 1 power electronics devices
The document is a report prepared by Meraj Akhtar of the Electrical Department at Jahangirabad Institute of Technology in Barabanki, Uttar Pradesh. It discusses electrical topics and was created by Meraj Akhtar for the Electrical Department at their university.
EE-55 Power Cables Testing & Fault Location
Dr. Adel Al-Faraskoury will teach a course on power cable testing and fault location from December 27-31, 2015 in Dubai, UAE. The course will cover topics such as partial discharge techniques, very low frequency testing, cable fault location methods, and cable failures and their analysis. It is aimed at engineers and technicians from electrical utilities and will help participants better understand cable testing and maintenance. Registration must be completed and paid for 25 days prior to the course date to receive an early bird discount.
ND
This document awards Whaleed Shadly Theron with the National Diploma in Engineering: Electrical from the Cape Peninsula University of Technology. Theron's student number is listed as 207083851. The document is signed by the Vice-Chancellor and dated 209 177.
Recommended
Cables and Connectors
This document discusses cables and connectors used in audio applications. It covers the different types of cables including straight pair, twisted pair, coaxial, and fiber optic cables. Straight pair cables are used to power speakers while microphone cables use XLR or D-sub connectors. Coaxial cables transmit digital audio signals. The document also discusses balanced and unbalanced signals, various audio connectors, and applications of different cables and connectors in audio systems.
1.government college of engineering
This seminar report discusses flexible electronics. It begins with an introduction to flexible electronics, including a brief history. It then describes flexible circuit structures and components such as resistors, capacitors, batteries, and displays. The report outlines the manufacturing process for flexible electronics using thin film transistors. Finally, it discusses the future scope and applications of flexible electronics, highlighting growth in markets. Potential applications include wearable devices, cell phones, and military/space uses. Both advantages like flexibility and disadvantages like high costs are noted.
2.1.3short Circuit
A short circuit occurs when a current travels along an unintended path with low resistance, allowing excessive current to flow. This can damage electrical equipment by overheating wires or melting insulation. Proper protective devices like fuses or circuit breakers are installed to detect abnormal currents and disconnect power before damage occurs.
WIRELESS POWER TRANSMISSION
THIS PPT IS BASED ON THE WIRELESS POWER TRANSMISSION AND THIS PPT IS MAINLY BASED ON THE UPCOMING WIRELESS TRANSMISSION IN THE CHARGING OF VEHICLES AND MOBILE PHONES THROUGH THE UPCOMING TECHNOLOGY IN THE POWER TRANSMISSION AND THIS IS SO HELP FULL TO THE ELECTRICAL AND ELECTRONICS ENGINEERING STUDENTS
Unit 4 ac voltage controller
This document was prepared by Meraj Akhtar of the Electrical Department at Jahangirabad Institute of Technology in Barabanki, Uttar Pradesh, India. It discusses electrical topics related to Meraj Akhtar's work in the Electrical Department at the Jahangirabad Institute of Technology.
Unit 1 power electronics devices
The document is a report prepared by Meraj Akhtar of the Electrical Department at Jahangirabad Institute of Technology in Barabanki, Uttar Pradesh. It discusses electrical topics and was created by Meraj Akhtar for the Electrical Department at their university.
EE-55 Power Cables Testing & Fault Location
Dr. Adel Al-Faraskoury will teach a course on power cable testing and fault location from December 27-31, 2015 in Dubai, UAE. The course will cover topics such as partial discharge techniques, very low frequency testing, cable fault location methods, and cable failures and their analysis. It is aimed at engineers and technicians from electrical utilities and will help participants better understand cable testing and maintenance. Registration must be completed and paid for 25 days prior to the course date to receive an early bird discount.
ND
This document awards Whaleed Shadly Theron with the National Diploma in Engineering: Electrical from the Cape Peninsula University of Technology. Theron's student number is listed as 207083851. The document is signed by the Vice-Chancellor and dated 209 177.
Design of Handphone Wireless Charger System Using Omnidirectional Antenna
Using cable as power transmission medium cause problem in flexibility and aesthetics. Wireless
power transmission for charging handphone releasednowadays still using antenna with radiation pattern
focus in one direction, that is just toward the top, and if the antenna was shifted then power transmitted will
be lose. The purpose of this research is to produce wireless power charger system used for charging
handphone power using resonator based on omnidirectional antenna and test the performance.
The device in this research was designed in two main part, that is transmitter and receiver. In
transmission section, there is power supply used for supplying power to oscillator to generate oscillating
signal in the form of electrical power to be transmitted to receiver via antenna in the form magnetic field. In
receiver section, receiver antenna received the power transmitted that is still in the reach of magnetic field
generated by transmitter. The power that is still in the form of oscillating signal, then stabilized for the
purpose of handphone power using rectifier and voltage regulator.
Design has been made successfully to the form of handphone battery power wireless
chargerusing omdirectional antenna which consist of two main part, that is transmitter and receiver. The
transmitted power is 3.058 watt with frequency 714 KHz, and receiver received the power and then
stabilized the signal to produce output power 58.706 miliwatt. This device can transmit power in all
directions horizontally (angle 360°). This device also tested with some kind of obstacle, with the result
almost all obstacle still could transmit the power except metal.
Even & Odd Signals |Solved Problems|
This document discusses even and odd signals in digital signal processing. It presents four problems related to classifying signals as even or odd. The problems are part of a lecture on digital signal processing and its applications being taught by Dr. M. Bakrutheen and Mr. K. Karthik Kumar in the Department of Electrical and Electronics Engineering at National Engineering College.
Front page & cert
This seminar report discusses the electrical machines used in electric power steering applications. It was submitted by Abhishek C Babu to the Department of Electrical and Electronics Engineering at Universal Engineering College in Thrissur, India, in partial fulfillment of the requirements for a Bachelor of Technology degree. The report was certified by the seminar coordinator, guide, and head of the department as covering electrical machines used for electric power steering.
2.2.7relays
This document discusses applied electrical technology. It focuses entirely on applied electrical technology by repeating that phrase multiple times. In a concise manner, the document covers applied electrical technology.
2.3.7earth Leakage
This document discusses applied electrical technology. It focuses entirely on applied electrical technology by repeating that phrase multiple times. In a concise manner, the document covers applied electrical technology.
2.3.3ratings
This document discusses applied electrical technology. It focuses entirely on applied electrical technology by repeating that phrase multiple times. In a concise manner, the document covers applied electrical technology.
2010fall ch7 zolboo
This document discusses outside plant technology including supporting structures, cable characteristics, underground cable, feeder and distribution cable, protection methods, and outside plant application issues. It describes the different types of supporting structures for cable including aerial, underground in conduit, and directly buried. Cable characteristics like twisted pair and sheath materials are also covered. The document outlines various protection methods for outside plant like insulating equipment, shielding cables, grounding, opening circuits, and separating power and telecom lines. Finally, it mentions considering plans for both fiber and copper cable and using flexible conduit for underground installation depending on the number of stations.
Elektronik
Electronics deals with electrical circuits that involve active electrical components such as vacuum tubes, transistors, diodes and integrated circuits, and associated passive interconnection technologies. The nonlinear behaviour of active components and their ability to control electron flows makes amplification of weak signals possible and electronics is widely used in information processing, telecommunications, and signal processing. The ability of electronic devices to act as switches makes digital information processing possible. Interconnection technologies such as circuit boards, electronics packaging technology, and other varied forms of communication infrastructure complete circuit functionality and transform the mixed components into a regular working system.
http://misscareful.blogspot.com/2013/09/elektronik.html
2.4.3derived
This document discusses applied electrical technology and its applications. It focuses on how electrical technology can be applied in practical and useful ways. The key topic covered is applying electrical principles to benefit and assist people in their daily lives and work.
Coursera powerelectronics 2015
Anant Kumar Verma completed the 9 week online course "Introduction to Power Electronics" through Coursera with distinction. The certificate was issued by Prof. Robert Erickson of the University of Colorado Boulder's Department of Electrical, Computer, and Energy Engineering and verified through Coursera, though it does not confer university credit.
azhar ali cv new 2
Azhar Ali is an electronic engineer seeking a position displaying his skills in power systems and projects. He has over 5 years of experience in testing, commissioning, protection, and maintenance of substations up to 500kV. His responsibilities include testing transformers, relays, circuit breakers, and more. He has a bachelor's degree in electronic engineering and technical training in transformer and line protection.
2.3.6physical
This document discusses applied electrical technology. It focuses on how electrical technology can be applied in practical ways. The key topic covered is applied electrical technology.
Flexible electronics paper
Flexible electronics is a new technology that uses flexible plastic substrates to assemble electronic circuits. This allows electronics to be lightweight, robust, high density, and conformable. Flexible circuits can be rolled up when not in use. There are several manufacturing techniques for flexible electronics including using polymers like PDMS and conducting adhesives. Applications include displays, solar cells, smart textiles, electronic paper, and healthcare devices. However, challenges remain regarding electrical stability, flexible substrate handling, and flexible conductor properties. The future of flexible electronics is promising with a growing market expected to reach $300 billion by 2028 as the technology enables new applications.
Flexible Electronics
It gives about the definition,history,manufacturing,applications,advantages and disadvantages of flexible electronics.
Cell tower radiation report
This document summarizes research on cell phone tower radiation and associated health risks. It discusses:
1) Radiation levels from cell towers are much higher than needed for communication near the towers, exposing some residents to radiation levels equivalent to being in a microwave oven for 19 minutes per day.
2) International safety guidelines vary widely, with some countries adopting limits 100-1000 times lower than India's guidelines.
3) Numerous studies have found health effects from radiation levels below current safety guidelines, including increased cancer risk, DNA damage, and effects on brain function, fertility, and more. Therefore, current safety limits may not adequately protect public health.
4) Both thermal and non-thermal effects of radiation need
JMV LPS Ltd Make in India Product for SolarPv,High Energy Storage and Electri...
JMV LPS Ltd Make in India Product for SolarPv,High Energy Storage and Electri...Mahesh Chandra Manav
JMV LPS Ltd Offer Electrical Safety Product for Solar PV ,High Energy Storage ,Electric Vehicle Charging Infra Earthing ,Lightning and Surge Protection ,AJB/DCDB, MC4 Connectors,
Useful Information for SECI,MNRE,NTPC,BHEL,NHPC,SVJN, State Electricity Board,State Power Generation Companies, State Renewable Power Generation Companies, Smart City Projects by States,Ministry of Power ,Ministry of Renewable,Discom Companies,Solar Power Developers,Solar EPC Companies Ground Mounted,Roof Top Projects, Indian Railways ,DMRC,2.3.5circuitbreaker
This document discusses applied electrical technology, with the phrase "Applied Electrical Technology" repeated multiple times. In a concise manner, it focuses on electrical technology and its applications, as the core subject of the content.
Latest ese type la nfc17 102(2011) -1
The document discusses the French Standard NFC 17-102 for Early Streamer Emission (ESE) lightning protection systems from September 2011. It provides an overview of how the standard harmonizes with other European standards EN 62305 and EN 50164 for lightning protection. The standard includes comprehensive testing requirements for ESE lightning protection components and systems to ensure proper functioning and quality. It aims to provide design requirements and quality standards for ESE lightning protection technology and become an international reference for countries using ESE systems.
Gps interface in gsm network
Anup Kumar submitted a seminar report on a GPS interface in a GSM network. He expressed gratitude to his guide Er. Debasish Mishra and the Head of the Electrical Engineering Department Prof. Dr. N.R. Samal for their support and guidance. The report described a vehicle tracking system that uses GPS and GSM technologies to track the location of a vehicle and transmit it to a monitoring unit via SMS. The system provides security against vehicle theft and allows owners to monitor vehicles' locations from anywhere. Potential applications include stolen vehicle recovery, fleet management, and delivery services.
Gps interface in gsm network
This document discusses the integration of GPS and GSM technologies for vehicle tracking. It begins with introductions to GPS and GSM systems, explaining how GPS provides location data via satellites and GSM enables wireless communication. The working principle is described, involving GPS receivers detecting satellite signals to determine position, which is then sent via GSM. A block diagram of the GPS tracker circuit is presented. Advantages include stolen vehicle recovery and remote location monitoring. Future applications could include animal tracking and delivery services. The document concludes that combining GPS, GSM, and a web app allows for more secure vehicle monitoring.
Modelling of Speed Observer System PPT
This document summarizes a student project on modeling a speed observer system for sensorless control of a three-phase induction motor. It includes:
1) An introduction to commonly used speed sensors and their disadvantages, leading to the motivation for sensorless control which estimates speed without sensors.
2) Explanations of key concepts needed for the speed observer system like coordinate transformations between reference frames, Clarke and Park transformations, and modeling of motor quantities like currents and voltages in the d-q reference frame.
3) An overview of the speed observer system including its basic block diagram and how it estimates speed for sensorless control by placing an observer in the control loop without direct speed feedback.
14. a variable speed, sensorless, induction motor drive
The document presents a new sensorless control strategy for a three-phase induction motor drive using only DC link current measurements. The strategy estimates motor speed and torque through signal reconstruction rather than direct sensor readings. It includes independent speed and torque control loops as well as current regulation. Simulation results on a 2.2 kW induction motor show fast dynamic response and good agreement between actual and estimated torque and speed values. The proposed drive requires only one current sensor in the DC link, making it suitable for low-cost sensorless motor applications.
More Related Content
What's hot
Design of Handphone Wireless Charger System Using Omnidirectional Antenna
Using cable as power transmission medium cause problem in flexibility and aesthetics. Wireless
power transmission for charging handphone releasednowadays still using antenna with radiation pattern
focus in one direction, that is just toward the top, and if the antenna was shifted then power transmitted will
be lose. The purpose of this research is to produce wireless power charger system used for charging
handphone power using resonator based on omnidirectional antenna and test the performance.
The device in this research was designed in two main part, that is transmitter and receiver. In
transmission section, there is power supply used for supplying power to oscillator to generate oscillating
signal in the form of electrical power to be transmitted to receiver via antenna in the form magnetic field. In
receiver section, receiver antenna received the power transmitted that is still in the reach of magnetic field
generated by transmitter. The power that is still in the form of oscillating signal, then stabilized for the
purpose of handphone power using rectifier and voltage regulator.
Design has been made successfully to the form of handphone battery power wireless
chargerusing omdirectional antenna which consist of two main part, that is transmitter and receiver. The
transmitted power is 3.058 watt with frequency 714 KHz, and receiver received the power and then
stabilized the signal to produce output power 58.706 miliwatt. This device can transmit power in all
directions horizontally (angle 360°). This device also tested with some kind of obstacle, with the result
almost all obstacle still could transmit the power except metal.
Even & Odd Signals |Solved Problems|
This document discusses even and odd signals in digital signal processing. It presents four problems related to classifying signals as even or odd. The problems are part of a lecture on digital signal processing and its applications being taught by Dr. M. Bakrutheen and Mr. K. Karthik Kumar in the Department of Electrical and Electronics Engineering at National Engineering College.
Front page & cert
This seminar report discusses the electrical machines used in electric power steering applications. It was submitted by Abhishek C Babu to the Department of Electrical and Electronics Engineering at Universal Engineering College in Thrissur, India, in partial fulfillment of the requirements for a Bachelor of Technology degree. The report was certified by the seminar coordinator, guide, and head of the department as covering electrical machines used for electric power steering.
2.2.7relays
This document discusses applied electrical technology. It focuses entirely on applied electrical technology by repeating that phrase multiple times. In a concise manner, the document covers applied electrical technology.
2.3.7earth Leakage
This document discusses applied electrical technology. It focuses entirely on applied electrical technology by repeating that phrase multiple times. In a concise manner, the document covers applied electrical technology.
2.3.3ratings
This document discusses applied electrical technology. It focuses entirely on applied electrical technology by repeating that phrase multiple times. In a concise manner, the document covers applied electrical technology.
2010fall ch7 zolboo
This document discusses outside plant technology including supporting structures, cable characteristics, underground cable, feeder and distribution cable, protection methods, and outside plant application issues. It describes the different types of supporting structures for cable including aerial, underground in conduit, and directly buried. Cable characteristics like twisted pair and sheath materials are also covered. The document outlines various protection methods for outside plant like insulating equipment, shielding cables, grounding, opening circuits, and separating power and telecom lines. Finally, it mentions considering plans for both fiber and copper cable and using flexible conduit for underground installation depending on the number of stations.
Elektronik
Electronics deals with electrical circuits that involve active electrical components such as vacuum tubes, transistors, diodes and integrated circuits, and associated passive interconnection technologies. The nonlinear behaviour of active components and their ability to control electron flows makes amplification of weak signals possible and electronics is widely used in information processing, telecommunications, and signal processing. The ability of electronic devices to act as switches makes digital information processing possible. Interconnection technologies such as circuit boards, electronics packaging technology, and other varied forms of communication infrastructure complete circuit functionality and transform the mixed components into a regular working system.
http://misscareful.blogspot.com/2013/09/elektronik.html
2.4.3derived
This document discusses applied electrical technology and its applications. It focuses on how electrical technology can be applied in practical and useful ways. The key topic covered is applying electrical principles to benefit and assist people in their daily lives and work.
Coursera powerelectronics 2015
Anant Kumar Verma completed the 9 week online course "Introduction to Power Electronics" through Coursera with distinction. The certificate was issued by Prof. Robert Erickson of the University of Colorado Boulder's Department of Electrical, Computer, and Energy Engineering and verified through Coursera, though it does not confer university credit.
azhar ali cv new 2
Azhar Ali is an electronic engineer seeking a position displaying his skills in power systems and projects. He has over 5 years of experience in testing, commissioning, protection, and maintenance of substations up to 500kV. His responsibilities include testing transformers, relays, circuit breakers, and more. He has a bachelor's degree in electronic engineering and technical training in transformer and line protection.
2.3.6physical
This document discusses applied electrical technology. It focuses on how electrical technology can be applied in practical ways. The key topic covered is applied electrical technology.
Flexible electronics paper
Flexible electronics is a new technology that uses flexible plastic substrates to assemble electronic circuits. This allows electronics to be lightweight, robust, high density, and conformable. Flexible circuits can be rolled up when not in use. There are several manufacturing techniques for flexible electronics including using polymers like PDMS and conducting adhesives. Applications include displays, solar cells, smart textiles, electronic paper, and healthcare devices. However, challenges remain regarding electrical stability, flexible substrate handling, and flexible conductor properties. The future of flexible electronics is promising with a growing market expected to reach $300 billion by 2028 as the technology enables new applications.
Flexible Electronics
It gives about the definition,history,manufacturing,applications,advantages and disadvantages of flexible electronics.
Cell tower radiation report
This document summarizes research on cell phone tower radiation and associated health risks. It discusses:
1) Radiation levels from cell towers are much higher than needed for communication near the towers, exposing some residents to radiation levels equivalent to being in a microwave oven for 19 minutes per day.
2) International safety guidelines vary widely, with some countries adopting limits 100-1000 times lower than India's guidelines.
3) Numerous studies have found health effects from radiation levels below current safety guidelines, including increased cancer risk, DNA damage, and effects on brain function, fertility, and more. Therefore, current safety limits may not adequately protect public health.
4) Both thermal and non-thermal effects of radiation need
JMV LPS Ltd Make in India Product for SolarPv,High Energy Storage and Electri...
JMV LPS Ltd Make in India Product for SolarPv,High Energy Storage and Electri...Mahesh Chandra Manav
JMV LPS Ltd Offer Electrical Safety Product for Solar PV ,High Energy Storage ,Electric Vehicle Charging Infra Earthing ,Lightning and Surge Protection ,AJB/DCDB, MC4 Connectors,
Useful Information for SECI,MNRE,NTPC,BHEL,NHPC,SVJN, State Electricity Board,State Power Generation Companies, State Renewable Power Generation Companies, Smart City Projects by States,Ministry of Power ,Ministry of Renewable,Discom Companies,Solar Power Developers,Solar EPC Companies Ground Mounted,Roof Top Projects, Indian Railways ,DMRC,2.3.5circuitbreaker
This document discusses applied electrical technology, with the phrase "Applied Electrical Technology" repeated multiple times. In a concise manner, it focuses on electrical technology and its applications, as the core subject of the content.
Latest ese type la nfc17 102(2011) -1
The document discusses the French Standard NFC 17-102 for Early Streamer Emission (ESE) lightning protection systems from September 2011. It provides an overview of how the standard harmonizes with other European standards EN 62305 and EN 50164 for lightning protection. The standard includes comprehensive testing requirements for ESE lightning protection components and systems to ensure proper functioning and quality. It aims to provide design requirements and quality standards for ESE lightning protection technology and become an international reference for countries using ESE systems.
What's hot (18)
Design of Handphone Wireless Charger System Using Omnidirectional Antenna
Design of Handphone Wireless Charger System Using Omnidirectional Antenna
JMV LPS Ltd Make in India Product for SolarPv,High Energy Storage and Electri...
JMV LPS Ltd Make in India Product for SolarPv,High Energy Storage and Electri...
Viewers also liked
Gps interface in gsm network
Anup Kumar submitted a seminar report on a GPS interface in a GSM network. He expressed gratitude to his guide Er. Debasish Mishra and the Head of the Electrical Engineering Department Prof. Dr. N.R. Samal for their support and guidance. The report described a vehicle tracking system that uses GPS and GSM technologies to track the location of a vehicle and transmit it to a monitoring unit via SMS. The system provides security against vehicle theft and allows owners to monitor vehicles' locations from anywhere. Potential applications include stolen vehicle recovery, fleet management, and delivery services.
Gps interface in gsm network
This document discusses the integration of GPS and GSM technologies for vehicle tracking. It begins with introductions to GPS and GSM systems, explaining how GPS provides location data via satellites and GSM enables wireless communication. The working principle is described, involving GPS receivers detecting satellite signals to determine position, which is then sent via GSM. A block diagram of the GPS tracker circuit is presented. Advantages include stolen vehicle recovery and remote location monitoring. Future applications could include animal tracking and delivery services. The document concludes that combining GPS, GSM, and a web app allows for more secure vehicle monitoring.
Modelling of Speed Observer System PPT
This document summarizes a student project on modeling a speed observer system for sensorless control of a three-phase induction motor. It includes:
1) An introduction to commonly used speed sensors and their disadvantages, leading to the motivation for sensorless control which estimates speed without sensors.
2) Explanations of key concepts needed for the speed observer system like coordinate transformations between reference frames, Clarke and Park transformations, and modeling of motor quantities like currents and voltages in the d-q reference frame.
3) An overview of the speed observer system including its basic block diagram and how it estimates speed for sensorless control by placing an observer in the control loop without direct speed feedback.
14. a variable speed, sensorless, induction motor drive
The document presents a new sensorless control strategy for a three-phase induction motor drive using only DC link current measurements. The strategy estimates motor speed and torque through signal reconstruction rather than direct sensor readings. It includes independent speed and torque control loops as well as current regulation. Simulation results on a 2.2 kW induction motor show fast dynamic response and good agreement between actual and estimated torque and speed values. The proposed drive requires only one current sensor in the DC link, making it suitable for low-cost sensorless motor applications.
MEMS Techanology full seminar report
Mems techanology full seminar report.
full details of mems technolgy total 33 page report.
plz downlod and enjoy now thanks.
Coin based mobile charging using solar tracking system
Now a days students and many other people use the public transportation , people who are making very long journey in order attend business conventions, conferences, or for any private purpose don’t know that their battery level is low and they often forget their charger at home or in hotel rooms. In rural areas there is no continuous power supply about 13-14 hours. Many times battery becomes flat in the middle of conversation particularly at inconvenient times when access to a standard charger isn't possible . Many critics argued that long distance traveling vehicles provides power points. Even though one or two power points are provided at a particular place in the vehicles it is not all sufficient for all the passengers, therefore need to provide a public charging service is essential and coin-based mobile battery chargers are designed to solve these problems
Coin based mobile charger project report
This document provides an overview of a coin-based mobile phone charging system. The system uses a coin recognition module to detect valid coins, and a microcontroller then activates the charging mechanism for a predefined period of time. It is intended for use in public places to allow mobile phone users to charge their phones for a small fee. The document describes the components, including the microcontroller, LCD display, and crystal oscillator used to generate the system clock signal. It provides block diagrams and explanations of how the various modules interact and function within the overall system.
Dcs course
This document provides an overview of distributed control systems (DCS) and programmable logic controllers (PLC). It defines DCS and PLCs, compares them, and describes their basic components and functions. The key aspects covered are:
1) DCS are integrated control systems used for complex, large-scale processes, while PLCs are used for discrete and small-scale control.
2) Both have centralized processing units and input/output modules to interface with field devices.
3) DCS are designed for continuous long-term use, while PLCs are more modular project-based systems.
vector control of induction motor
1) The document describes speed control of an induction motor using vector control. Vector control allows independent control of the flux and torque producing components of stator current.
2) A Clarke transformation converts the 3-phase stator currents to a 2-phase stationary reference frame. Then a Park transformation aligns one component with the rotor flux to control flux and the other to control torque.
3) Simulation results show the rotor speed, torque, stator currents in the direct-quadrature frame, and calculated three-phase voltages matching the objectives of vector control.
Speed detection-of-moving-vehicle-using-speed-cameras
Speed detection-of-moving-vehicle-using-speed-cameras IS A WAY OF TRAFFIC RULE IMPLETENTION USING VISUAL CAMERA TECHNOLOGY
Distributed Control System
A distributed control system (DCS) provides safe, efficient, and reliable control of critical components in a thermal power plant. Key benefits of a DCS include high reliability, improved response time, improved operator interface, and historical data storage. A DCS uses controller cards, input/output cards, and communication cards to monitor and control elements like valves, pumps, temperatures, and pressures. Operators interact with the DCS through workstations with displays for alarms, graphics, trends, and reports. Automatic controls help optimize processes while interlocks ensure safe operation during startups, run cycles, and shutdowns.
DCS Or PLC
This document discusses the differences between programmable logic controllers (PLCs) and distributed control systems (DCSs) in order to help determine which type of system is best suited for different applications. It outlines seven key questions to consider regarding the manufacturing process, product value, system requirements, operator needs, engineering expectations, and whether the application is hybrid in nature. PLCs are generally better for discrete and simple batch control, while DCSs are more suitable for complex batch processes and facilities that require flexibility and recipe management where system availability is critical. A hybrid system may be needed if an application requires both fast logic control and regulatory analog loop control.
Mems (Detail Presentation)
Micro-Electro-Mechanical Systems (MEMS) are small integrated devices that combine electrical and mechanical components. MEMS fabrication involves depositing thin films, lithography to pattern the films, and etching to selectively remove material. MEMS can be fabricated using processes like thermal oxidation, deposition, doping, etching, and lithography. Applications of MEMS include sensors, actuators, mirrors, and biomedical devices. MEMS technology is expected to continue advancing and enabling new applications in fields such as computing, communications, and transportation.
Advantages and Disadvatages of AC/DC Motor
Simple explanation on advantages and disadvantages of AC and DC motor. Focusing on main point only since the slides is for presentation. Originally design by me.
Power generation from speed breakers
This document describes a design for a speed bump that generates electricity from the kinetic energy of passing vehicles. It discusses two mechanisms - a spring coil mechanism and rack pinion mechanism - that use vehicles compressing the speed bump to power an electrical generator. The spring coil mechanism uses compressed air from the speed bump to power an air turbine connected to the generator. The design aims to reduce wasted energy from vehicles braking at speed bumps and provide a small amount of renewable energy.
mems ppt
MEMS (micro-electro-mechanical systems) combine mechanical and electrical functions on a single chip using microfabrication technology. The fabrication process for MEMS is similar to that used for making electronic circuits and involves steps such as chemical deposition, physical deposition, lithography, and etching. MEMS can be used to develop microsensors using materials like metals, polymers, ceramics, semiconductors, and composites. Common applications of MEMS include accelerometers, which have advantages over conventional accelerometers such as lower cost, smaller size, and lower power requirements.
Li-Fi
In simple terms, Li-Fi can be thought of as a light-based Wi-Fi. That is, it uses light instead of radio waves to transmit information. And instead of Wi-Fi modems, Li-Fi would use transceiver-fitted LED lamps that can light a room as well as transmit and receive information. Since simple light bulbs are used, there can technically be any number of access points.
This technology uses a part of the electromagnetic spectrum that is still not greatly utilized- The Visible Spectrum. Light is in fact very much part of our lives for millions and millions of years and does not have any major ill effect. Moreover there is 10,000 times more space available in this spectrum and just counting on the bulbs in use, it also multiplies to 10,000 times more availability as an infrastructure, globally.
Gsm.....ppt
Global System for Mobile (GSM) is a second generation cellular standard developed for voice services and data delivery using digital modulation. It has a network subsystem including components like the MSC, HLR, VLR, and AuC that handle call processing and subscriber information. The radio subsystem consists of BSCs controlling multiple BTSs to manage radio network access. GSM provides international roaming, high quality voice calls, and supports data services like SMS and fax in addition to voice.
coin based mobile battery charger
This document proposes the design of a solar-powered public mobile phone charging station. It includes an introduction, objectives, assumptions, block diagram, description of components, charging requirements, flow chart, powering details, specifications, advantages, applications, and conclusion with references. The key components are a solar panel, microcontroller, coin sensor, LCD display, and mobile phone charging terminals that can accommodate different types of phones. It is presented as a low-cost solution for charging mobile phones in rural areas without reliable grid access.
Viewers also liked (20)
14. a variable speed, sensorless, induction motor drive
14. a variable speed, sensorless, induction motor drive
Coin based mobile charging using solar tracking system
Coin based mobile charging using solar tracking system
Speed detection-of-moving-vehicle-using-speed-cameras
Speed detection-of-moving-vehicle-using-speed-cameras
GPS INTERFACE IN GSM NETWORK
- 1. A SEMINAR REPORT ON GPS INTERFACE IN GSM NETWORK In partial fulfilment for award of the degree of Bachelor of Technology In Electrical Engineering Under the guidance of Er.Debashish Mishra ORISSA ENGINEERING COLLEGE, BHUBANESWAR BIJU PATNAIK UNIVERSITY OF TECHNOLOGY, ODISHA Submitted by: Name: Anup Kumar Roll No: 125120 Regd. No: 1201211212 Session: 2012-16 Department of Electrical Engineering