This document summarizes a lab report on designing and testing an open loop buck converter circuit. The circuit was first designed and tested in simulations to ensure it met specifications. Key parameters like inductor and capacitor values were calculated. Simulation tests showed the output voltage met requirements when load current was varied and efficiency was above 75% at maximum load. Hardware was then implemented using the simulated design. Testing of the built circuit showed results matching simulations, with output voltage and current values meeting requirements when load was changed and dynamic voltage changes below 0.75V.
Boost Converter and analysis its characteristicsADARSH KUMAR
ABSTRACT
The switching mode power supply market is flourishing quickly in today’s world. Design engineers aren’t always supplied with the desired amount of voltage they need in order to make their design function properly. Adding an extra voltage supply to a design is not always cost efficient. This project is proposed to provide a method of boosting DC voltage from 5 Volts to 15 Volts, by using a boost converter designed specifically for this task. All aim, calculations, tests, data and conclusions have been documented within this project. Results of simulation show that the switching converter will boost voltage from 5 volts to 15 volts with power conversion efficiency of 94.16 percent.
Boost Converter and analysis its characteristicsADARSH KUMAR
ABSTRACT
The switching mode power supply market is flourishing quickly in today’s world. Design engineers aren’t always supplied with the desired amount of voltage they need in order to make their design function properly. Adding an extra voltage supply to a design is not always cost efficient. This project is proposed to provide a method of boosting DC voltage from 5 Volts to 15 Volts, by using a boost converter designed specifically for this task. All aim, calculations, tests, data and conclusions have been documented within this project. Results of simulation show that the switching converter will boost voltage from 5 volts to 15 volts with power conversion efficiency of 94.16 percent.
Control And Programingof Synchronous Generatorfreelay
author: International Team
publisher: Daniel Garrido
licence: Creative Commons
place: University of Southern Denmark- Odense
@fomenting colaborational knowledge
Voltage Mode Control of Buck ConverterManish Kumar
Voltage Mode Control of Buck Converter (Dec 2012 - April 2013): The Buck-converter converts an input voltage into a lower output voltage, it is also called step-down converter. The buck converter is designed in continuous current conduction mode. To get the regulated output voltage, compensation mechanism using voltage mode control is used. This project involved simulation, design and hardware construction of voltage mode control of buck converter using PID compensator. The error signal is compared with a saw-tooth ramp voltage and desired PWM signal.
• Designed and developed a buck converter circuit using the PID Compensator to get a stable output of 5V-5A from an input of 12V.
• Circuit Simulation using ORCAD (PSpice); Stability analysis of the closed loop system for desired phase and
gain margin using MATLAB; Designed PID compensator by modifying the open loop buck converter circuit obtained by Simulation using ORCAD (PSpice). Implemented Compensator and PWM scheme using NXP LPC1768 Micro-controller.
A Five – Level Integrated AC – DC ConverterIJTET Journal
This paper presents the implementation of a new five – level integrated AC – DC converter with high input power factor and reduced input current harmonics complied with IEC1000-3-2 harmonic standards for electrical equipments. The proposed topology is a combination of boost input power factor pre – regulator and five – level DC – DC converter. The single – stage PFC (SSPFC) approach used in this topology is an alternative solution to low – power and cost – effective applications.
Introduction
Working Principle
Step Down and Step Up Cycloconverter
Single phase to single phase cycloconverter
Mid-Point and Bridge type cycloconverter
Advantages and disadvantages
Applications
It’s a power electronics project. It is able to give output voltage(DC) more and less than input voltage as per requirement.
We can generate variable DC voltage which is less than input, but, the special things about this converter is, it has capability to produce variable DC voltage as high as twice the input voltage.
We have specially designed and manufactured inductor for this project.
Control And Programingof Synchronous Generatorfreelay
author: International Team
publisher: Daniel Garrido
licence: Creative Commons
place: University of Southern Denmark- Odense
@fomenting colaborational knowledge
Voltage Mode Control of Buck ConverterManish Kumar
Voltage Mode Control of Buck Converter (Dec 2012 - April 2013): The Buck-converter converts an input voltage into a lower output voltage, it is also called step-down converter. The buck converter is designed in continuous current conduction mode. To get the regulated output voltage, compensation mechanism using voltage mode control is used. This project involved simulation, design and hardware construction of voltage mode control of buck converter using PID compensator. The error signal is compared with a saw-tooth ramp voltage and desired PWM signal.
• Designed and developed a buck converter circuit using the PID Compensator to get a stable output of 5V-5A from an input of 12V.
• Circuit Simulation using ORCAD (PSpice); Stability analysis of the closed loop system for desired phase and
gain margin using MATLAB; Designed PID compensator by modifying the open loop buck converter circuit obtained by Simulation using ORCAD (PSpice). Implemented Compensator and PWM scheme using NXP LPC1768 Micro-controller.
A Five – Level Integrated AC – DC ConverterIJTET Journal
This paper presents the implementation of a new five – level integrated AC – DC converter with high input power factor and reduced input current harmonics complied with IEC1000-3-2 harmonic standards for electrical equipments. The proposed topology is a combination of boost input power factor pre – regulator and five – level DC – DC converter. The single – stage PFC (SSPFC) approach used in this topology is an alternative solution to low – power and cost – effective applications.
Introduction
Working Principle
Step Down and Step Up Cycloconverter
Single phase to single phase cycloconverter
Mid-Point and Bridge type cycloconverter
Advantages and disadvantages
Applications
It’s a power electronics project. It is able to give output voltage(DC) more and less than input voltage as per requirement.
We can generate variable DC voltage which is less than input, but, the special things about this converter is, it has capability to produce variable DC voltage as high as twice the input voltage.
We have specially designed and manufactured inductor for this project.
This project is proposed to integrate the Fuel cell emulator with a boost converter and load the DC motor
and the performance analysis is done. Fuel cell as a renewable energy source is considered to be one of the most
promising sources of electrical power. The characteristics of fuel cell is such that the DC power extracted from it is
at low voltage level, this project proposes a prototype of a new power electronics based fuel cell emulator. After
proposing a fuel cell emulator, it is integrated with a boost converter and DC motor is loaded. After the successful
working of the boost converter, it can be directly connected with the actual Fuel Cell Systems (FCS) to satisfy the
DC motor load which is integrated with fuel cell emulator and boost converter.
AC-DC converters are widely used in industrial and domestic applications. Input AC voltage is rectified and
filtered using filtering circuit which consists of large electrolytic capacitors. These capacitors draw a large
amount of current and the efficiency of the converter system decreases drastically. large ripple factor have made the converter system inefficient .This paper
analyses about different converter topology and proposes a different design which is based on converting Ac signal to specified Dc signal of about 5V by which ripple factor can be reduced to make the system enough efficient. The implification of this project is for charging or operating semiconductor devices .The results of respective topologies are shown through P-simulation program with integrated circuit emphasis (PSPICE) simulation and their
parameters are calculated. Three parameters are considered for the comparison of these topologies
This paper introduces a new topology of multilevel inverter, which is able to operate at high performance. This proposed circuit achieves requirements of reduced number of switches, gate-drive circuits, and high design flexibility. In most cases fifteen-level inverters need at least twelve switches. The proposed topology has only ten switches. The inverter has a quasi-sine output voltage, which is formed by level generator and polarity changer to produce the desired voltage and current waveforms. The detailed operation of the proposed inverter is explained. The theoretical analysis and design procedure are given. Simulation results are presented to confirm the analytical approach of the proposed circuit. A 15-level and 31-level multilevel inverters were designed and tested at 50 Hz.
Comparative Steady State Analysis of Boost and Cascaded Boost Converter with ...IAES-IJPEDS
In this paper, an overall comparison between the Boost Converter (BC) &
Cascaded Converter/ Cascaded Boost Converter (CBC) has been depicted in
terms of ideal condition, as well as with the consideration of Equivalent
Series Resistance (ESR) of inductor(s). The loss comparison in the two
converters due to the ESR is also included in this paper. It can be seen that in
CBC, voltage gain is more but the power loss due to ESR is also more
compared to BC. The parameters of the converters are derived with a
consideration of per unit ripple quantity of inductor current and capacitor
voltage. A boundary condition between the continuous conduction mode
(CCM) & discontinuous conduction mode (DCM) of the inductor current is
also shown. The behaviour of the capacitor current for the converters is
discussed during ON and OFF condition of the switch(es) during DCM. At
the end, the simulation results of both the converters are given for a
20V/100V, 100 W output. The analysis and simulation results are presented
in this paper for the verification of the feasibility.
Supplementary material for the article: “Pseudo DC-link EV Home Charger with ...Hamed Heydari
THE supplementary information for the paper:” Pseudo DC-link EV Home Charger with a High Semiconductor Device Utilization Factor” [1] is presented in this document. [1] H. Heydari-doostabad, S. H. Hosseini, R. Ghazi, and T. O’Donnell, “Pseudo DC-link EV Home Charger with a High Semiconductor Device Utilization Factor,” IEEE Trans. Ind. Electro., vol. 1, no. 1, p. 1, 2021.
A New Multilevel Inverter Structure For High-Power Applications using Multi-c...IJPEDS-IAES
In recent, several numbers of multilevel inverter structures have been
introduced that the numbers of circuit devices have been reduced. This paper
introduces a new structure for multilevel inverter which can be used in highpower
applications. The proposed topology is based on cascaded connection
of basic units. This topology consists of minimum number of circuit
components such as IGBT, gate driver circuit and antiparallel diode. For
proposed topology, two methods are presented for determination of dc
voltage sources values. Multi-carrier PWM method for 25-level proposed
topology is used. Verification of the analytical results is done using
MATLAB simulation.
A High Step Up Hybrid Switch Converter Connected With PV Array For High Volt...ijitjournal
T
his paper
presents
a
ste
p up DC
-
to
-
DC converter with
hybrid switch capacitor technique having
high
voltage conversion ratio with small
switch voltage stress
. The converter is suitable for the applications
where high voltage conversion is required. The proposed
DC
-
DC converter
has low voltage ratted
MOSFET switch and is connected to PV array to get high output voltage at small duty ratios.
Hence it has
high efficiency.
The principles of operations and the theoretical analysis are presented in this paper.
All the
simulations are
done in MATLAB
-
SIMULINK Environment and
results were obtained with voltage
conversion ratio of 4.
A LOW VOLTAGE DYNAMIC SYNCHRONOUS DC-DC BUCK-BOOST CONVERTER FOUR SWITCHES P singh
This paper presents the design and modeling of synchronous DC-DC buck-boost converter four switches controlled with PID controller for mobiles devices applications. The design of the converter circuit needs modeling and simulating its mathematical equations using MATLAB/SIMULINK. The evaluation of the output performance has been based on dynamic respond in term of rise time, settling time and peak time. Also the goal of the designer is regulated the output voltage to 3.24 regardless the variation of the input voltage, with input voltage [2.5V-5V] and switching frequency is 50 MHz. The converter is operated in Buck (step-down) and Boost (step-up) modes.
Electrical, Electronics and Computer Engineering,
Information Engineering and Technology,
Mechanical, Industrial and Manufacturing Engineering,
Automation and Mechatronics Engineering,
Material and Chemical Engineering,
Civil and Architecture Engineering,
Biotechnology and Bio Engineering,
Environmental Engineering,
Petroleum and Mining Engineering,
Marine and Agriculture engineering,
Aerospace Engineering.
2. 1 Introduction
The purpose of this lab is to use the theory of the buck converter to build one. This lab report is a
follow up from the simulations and will focus on the hardware part. The simulation results will
be presented again for comparison purposes and then the physical circuit will undergo tests that
were similarly ran in simulations. Finally, these results will be presented to check if the built
circuit will be able to replicate the results from the simulated circuit.
1.1 Design Specifications
a) Input voltage: 10V DC
b) Output voltage: 5V DC
c) Maximum load: 1000 mA
d) Minimum load: 100 mA
e) Output Ripple Voltage 0.2 Vpp
f) Efficiency: > 75 % at Maximum Load
g) Converter frequency: 50 kHz – 200 kHz.
h) Worst case dynamic voltage change: 0.75 V
2 Design Using Simulation
2.1 Inductor Value Selection
The following parameter values are given in Table 1 to find the inductor value needed for the
design:
Table 1. Given and Set/Chosen Parameters for the OpenLoop Buck Converter
Parameter Value
Input Voltage 10 V (DC)
Output Voltage 5 V (DC)
Max Load Current 1000 mA
Min Load Current 100 mA
Peaktopeak Ripple Voltage 0.2 V
Converter Frequency 50 kHz (chosen)
3.
In order to find the inductor value needed, delta inductor current had to be found first using the
following equation below:
.5 (1)D = V in
V out
= 5
10 = 0
i .2A (2)∆ L = Lfs
(V −V )Din out
= (5)(0.5)
(50k)(250μH) = 0
Then, the delta inductor current value was used to find the inductor value. Because we chose our
design to completely avoid discontinuous mode, the minimum load current was used in the
following equation below:
50μH (3)Lcrit = 2I fomin s
(V −V )Din out
= (10−5)(0.5)
(2)(0.1)(50k) = 2
The end calculations presented that a 250 inductor was needed to fulfill the design.Hμ
2.2 Capacitor Value Selection
Using the same parameters given in Table 1 and the delta inductor current, the following
equation was used to find the capacitance value needed:
≥ .5μF (4)C
∆iL
8V f0 s
= 0.2
(8)(0.2)(50k) = 2
With the given equation above, the design needed a capacitor value of at least 2.5 F in parallel μ
with the load. However, there are no 2.5 F capacitor values available; thus, a 3.3 F capacitor μ μ
was used for the simulation.
3 Open Loop Buck Converter Design
Figure 1 is the open loop buck converter design that will be built in this lab. The gate of the
MOSFET is connected to a similar representation of the MC34151 driver as it was not provided
in MULTISIM, but is replaced by the drive in the actual circuit.
5. 4.2 Inductor Current
Figure 3. Transient Analysis of the Buck Converter at different loads
Figure 3 shows two plots of the current load at different loads. The green waveform represents
the inductor current at high load current (Rload = 5 Ω) and the blue waveform represents the
inductor current at low load current (Rload = 50 Ω). The average, steadystate currents are near
what they should be in specifications.
4.3 Rapid Step Load Variation (Maximum to Minimum)
Figure 4. Transient Analysis of the output voltage ripple.
Figure 4 shows the output voltage when there is dynamic loading from maximum loading current
to minimum loading current. As of now, this voltage spike is too high and needs to be addressed
when building the hardware. One of the suggestions is to add a higher valued capacitor to reduce
the dynamic voltage change.
6. 4.4 Rapid Step Load Variation (Minimum to Maximum)
Figure 5. Transient Analysis of the output voltage ripple.
Similarly, Figure 5 shows the output voltage when there is dynamic loading from minimum
loading current to maximum loading current. As of now, this voltage spike is too high and needs
to be addressed when building the hardware. Mentioned before, adding a capacitor would be able
to reduce this dynamic voltage change.
4.5 Maximum Load (Rload = 5 Ω)
The sections below are analysis at maximum load current:
4.5.1 Voltage Ripple at Max Load
Figure 6. Transient Analysis of the output voltage ripple.
7. Figure 6 above shows the output voltage ripple at maximum load current. This plot shows that
the voltage ripple ranges from 0 to 4% which is within the acceptable range for the design.
4.5.2 Efficiency at Max Load
Figure 7. Transient Analysis of the Efficiency
Figure 7 displays the efficiency of the circuit, which shows that once in steady state, the
efficiency comes to be around 88%, which is above design’s requirement of 75% efficiency.
Cursor values: Pin avg = 5.0448 W; Pout avg = 4.436 W
00% 7.93 % (5)η = Pin
Pout
* 1 = 8
4.6 MOSFET Waveform
Figure 8. Transient Analysis of the Vgs and Vds of the MOSFET, the voltage of the diode, and the output voltage
8. Figure 8 displays the drain to source voltage of the MOSFET, the voltage of the diode, and the
voltage of the output. MOSFET turns on when the Vds is at least 10.65 V and the Vgs is at least
0.62 V. Thus, these values are the turn on settings for the MOSFET. Additionally, at these
voltage settings, the diode is turned off (the blue waveform) and in reverse bias, which would
also prove that the MOSFET is on in the buck converter.
5 Hardware Implementation
With the simulation results and calculations shown, the hardware test will be presented as
follows.
Before starting the hardware testing procedures, the inductor needed to be built using copper
wiring and a core. The calculation for the number of turns is as follows:
39.16 (6) N =
√ L
Al =
√163 10*
−9
250 10*
−6
=
The result was rounded to 40 turns and the resulting inductance was around 252 uH.
In addition, the capacitance value was increased to 1800 uF to reduce the output voltage ripple
and the dynamic voltage change, and a resistor of 1kΩ was added to the gate to smooth the gate
voltage and to reduce spiking.
5.1 Varying Load Current
Table 2: Different parameters of the circuit when the load current is varied from minimum to maximum
via change in load resistance
Rload(Ω) Vout(V) Iload(A) Vo/Vin
50 5.20 0.104 0.520
30 5.11 0.170 0.511
20 5.01 0.251 0.501
10 4.99 0.499 0.499
5 4.91 0.982 0.491
Table 2 summarizes the values of the load current and the ratio of the output and input voltages
when the load current is varied from minimum to maximum via change in load resistance.
9.
Figure 9. Load current vs Vo/Vin
Figure 9 shows the plot of the ratio of the output to the input voltage versus the load current. the
above plot is very similar to the theoretical version of the graph. In addition, this plot shows how
once load current reaches below a certain threshold, the circuit slowly goes into discontinuous
conduction mode.
5.2 Inductor Current
Figure 10 and 11 below show the current through the inductor for the highest and lowest load
currents. Although our waveform had large spikes for every new switching cycle of the
MOSFET due to transient effects of the switching, the ripple voltage without the peaks ranged
from 0.1 to 0.2 V, which is within specifications of the design.
Figure 10 shows the inductor current at maximum load
11. 5.4 Rapid Step Load Variation (Minimum to Maximum)
Figure 13 shows the shows a waveform of Vo versus time for rapid (step) load variation from
minimum to maximum. Similarly, using the higher capacitor value reduced the dynamic voltage
change from 7.5 V to at most 0.8 V.
Figure 13. Rapid load variation from min to max.
5.5 Maximum Load (Rload = 5 Ω)
Similar to the simulation tests, the following are measurements/waveforms of the circuit when
the circuit is operating a maximum load.
5.5.1 Output Voltage Ripple
Figure 14 shows the Output waveform and output voltage ripple versus time at max load.
Figure 14. Output voltage vs. Time at Max Load.
12. The calculations for the output voltage ripple are as follows at maximum load:
I 982 .964 A (7)ΔiL = 2 Omax = 2 * . = 1
v 0.0027 V (8)Δ o =
ΔiL
8Cfs
= 1.964
8 (50kHz)(1800μF)*
=
Although the measured output peaktopeak voltage ripple are different from the calculated as
done above, the measured output peaktopeak voltage of 0.12 V is within the specifications of
the lab.
5.5.2 Max Load Efficiency
Using the following measured parameters given below, the calculations for the efficiency are as
follows:
VMaxLoad = 4.91V Vin = 10V
Iout = 0.982 A IL = 0.54 A
Pout = 4.822 W Pin = 5.4W
RLoad = 5 ohm
Pout / Pin = Efficiency = 89.89% (9)
Calculations show that efficiency comes out to be around 89%, which is above the specification
requirement of 75%.
5.6 Power Loop Losses
From the max load efficiency section, the measured power loss comes out to be 0.578 W. The
following are the power dissipation for each element (note these are values at which the circuit
has reached steady state):
MOSFET Dissipation: 0.081 W
Inductor Dissipation: 0.093 W
Capacitor Dissipation(ESR): 0.200 W
Diode Dissipation: 0.373 W
R_Gate Dissipation: 0.126 W
13. 5.7 MOSFET Waveforms
Figure 15. Waveform of Vs(yellow), Vd(blue), and Vds(orange) of the MOSFET
As shown on Figure 15, the waveforms of the Vd, Vs, and Vds of the MOSFET were taken to
observe the turn on behavior. Similar to the simulation, the MOSFET turns on when Vds =
10.2V and when the source voltage becomes negative, which would mean that the diode is in
reverse bias. Although not pictured in the waveform, through calculations from the
measurements of the waveform, the MOSFET turns on when Vgs = 0.58 V.
5.8 Varying Vcc (Supply Voltage)
Figure 16. Output voltage at which Vcc = 10V
14. Additionally, the test was done to see what effect the output voltage would have if the supply
voltage were to decrease. In this case, the supply voltage decreased from 16V to 10V and
consequently, the output voltage decreased by 1.6 V (DC). This is the case because this would
decrease the output from the driver and in turn decrease Vgs. Consequently, the source current
that is fed into the inductor would decrease. Overall, this effectively reduces the current that
passes through the load, which in turn decrease the output DC voltage.
5.9 ESR Calculations
Figure 17. Test Circuit to find the ESR of C1
In order to calculate the ESR for one of the capacitor, the test circuit in Figure 17 was used. With
the capacitor nearly fully charged, the decay behavior needed to be observed when R2 = 1Ω &
2Ω. Figure 18 and Figure 19 display both decay behaviors. With these graphs, two points were
able to be extracted, respectively.
Figure 18. Exponential Decay Behavior with R2 = 1Ω
15.
Figure 19. Exponential Decay Behavior with R2 = 2Ω
Then using the following functions below, the tau values were able to be calculated along with
the ESR.
.39Eτ1 = 9 − 4
.41Eτ2 = 1 − 3
R21 = 1Ω, R22 = 2Ω
With all the calculations, ESR value of the 470 uF comes out to be approximately 0.99Ω, which
is high and expected of a highcapacitancevalued, electrolytic capacitor.
3 Conclusion
By using the current knowledge of the openloop buck converter, the parameters including the
capacitor and the inductor values needed were able to be found. Then we ran simulation tests in
order to prove that most of the circuit design was sufficient. The actual circuit was then built
with new adjustments as suggested from the simulation, which included adding a gate resistor
and a higher valued capacitor. As a result, the dynamic voltage change was greatly reduced to
within lab specifications along with the spiking. Overall, running the simulations and testing the
actual buckconverter circuit enabled us to learn the intricacies of the design, which helped us
improve our initial design and fix most of the problem associated with the hardware.