Ashok Jain is a 36-year-old Indian national who has over 15 years of experience in the wind and hydro energy industries. He has held various engineering roles at companies such as Vestas Wind Systems, VATech Hydro, and Leroy Somer & Controls, where he performed tasks like failure analysis, testing, design verification, and project coordination. Ashok holds a Bachelor's degree in Electrical Engineering and has expertise in areas including CAD, testing equipment, and PLC programming. He is currently seeking new opportunities.

1. ASHOK JAIN M: +45 60191891
Personnel Information Nationality: Indian
Age: 36 Years
Address Kirkegårdsvej 8a, 1th, Arhus, Denmark -8000
Email: ashokarhus@gmail.com
Qualification Bachelor of Science and Engineering (Electrical)
Proactive and progressive
Development of new methods and ideas
Experience:
JAN2012 –Dec2014 Assist. Lead Engineer at Vestas Wind Systems, Arhus, Denmark
· Process Failure Mode and Effects analysis (PFMEA) of different components of wind
turbine.
· Preparing process flow of the complete nacelle of world’s largest wind turbine.
· Coordinating with projects managers, designers, and technicians at the site.
· Collecting cost out ideas from various sources in production, design and evaluating
the saving potential. Preparing presentation to present to the management..
· Cost breakdown, cost calculation of each items using BOM of the new and old
assembly of different parts of the wind turbine.
· Engineering change management
· Coaching monitoring tools of the value chain.
· Coordination and arranging prototype test on all kind of wind generator upto 3.3MW –
Permanent magnet generator (PMG), Doubly Fed Induction generator (DFIG), IG.
· Test report preparation
· Data analysis of test results and projection to the team.
· Performing resistance measurement, High Voltage test, megger test, Partial
Discharge test etc.

2. · Travelling to various European countries to perform testing on wind generators.
Oct, 2008 - Jan, 2012 Assist. Lead Engineer, Vestas Technology R&D Chennai (Generator)
· Design verification procedures and reports on Permanent magnet generators and
singly fed induction generators (2MW/3MW) used in wind turbines.
· Verification of requirements of high speed PMG (up to 3MW):
Dimensions, Number of poles, heat run (efficiency calculation)Winding, bearing and
magnet temperature, sensors, lubrication, cooling system, power performance,
transportation, short circuit , enclosure protection, humidity, acoustic noise level ,
torque,, hot surface, impulse, , vibration, demonstration of exchange of generator in
nacelle
Sept, 2007 – Oct, 2008 Sr. Officer, VATech Hydro, Bhopal, India.
(Austrian Manuf. of Turbo & Hydro Generators for Hydro Power Plant)
· Tendering Documentation of Turbo & Hydro Generators for various customers
· Design and cost calculations of various parts of generators.
Sept, 2005 to Sept’2007 Sr. Design Engineer, Leroy Somer & Controls, NOIDA, India
(JV between Leroy Somer, France and controls & Switchgear, India)
· Electrical Design calculations & Development of generators.
· Electrical & mechanical verification of Alternators & Induction motors
· Electrical design using Flux 2D (French software),
Calculation of Ampere Turns in each part of magnetic circuit, Voltage profile,
Magnetic circuit calculations & optimization of lamination.
· Managing electrical lab consisting of Alternator Test Bench, Control panel, AC Drive
Panel, Auto Transformer, Inductive load, heating, load, Induction motor etc.
· Validation of Alternator which includes different Electrical Tests like:-
Open circuit, Short circuit, Harmonic, Transient, Resistance, Leakage Reactance
(Poitier’s Method), Temperature rise tests to validate thermal class of insulation,
Excitation curve / Voltage regulation Test, Residual voltage Vs. Frequency curve

3. · Instrumentation used: Fluke make Three Phase power analyzer, Scope meter,
Multimeters, clamp meters, & microhmmeter etc & HBM make Torquemeters &
software of all these instruments.
· DFMEA (Design Failure mode & Effects Analysis)
· Validating Automatic Voltage Regulators (AVR)
· Validated Leroy Somer, Mecccalte , Linz and Sincro alternators in the range of 5kVA
to 40kVA
July2004 to Aug2005 Utility Powertech Limted (JV between Reliance Energy and
National Thermal Power Corporation, India)
· AMC (annual maintenance) work of existing electrical distribution system of one
colony of Delhi which include Load balancing, Augmentation of distribution
Transformers.
· Transformer testing through megger, Transformer oil test, Open & Short Circuit Test,
laying feeder Cables, locating fault, Preventive maintenance of 11KV/415V substation
etc, dealing with vendors
· Manpower management.
· Low voltage distribution system (LVDS) & High voltage distribution system (HVDS)
· Single line Diagram of existing & proposed electrical system using AutoCAD
· Analyze the whole existing electrical system of the area, which is to be designed,
locating Feeders, making plot plan of the existing system.
· Load analysis of Transformer to determine the percentage loading of Transformer
and all its feeders & Feeder Pillars.
· Load loss calculation & voltage profile of the existing system.
· Design of the installation of LT Panels, Feeder pillars, APFC panels,
· Transformers, Package substation, RMUs, selection of cable size.
· Making BOQ, BOM, activity Sheet & Preparing the complete documentation
· Coordinating with erection team.
Training & Course attended during job:-
Institute/ Company Course / duration
CEDRAT, Grenoble France One week training on Flux 2D Software
Leroy Somer, Angouleme France 3 weeks training on Design of Alternators
Engineering Research and Development (ERDA),
Vadodara, India 3 days seminar on Conditioning monitor system of generators and

4. motors
Industiral Automation Training
Institue,Noida,India SCADA & PLC Based Control
Programming of Allen Bradley (SLC-500), Siemens (S7-200 &S7-
300) & Modicon PLCs
Worked with INTOUCH SCADA software for various applications.
Training on Drives & Control Panels
Training & Course attended during Engineering:-
Institute/ Company Course / duration
Bharat Heavy Electricals Ltd Hardwar This was an observational training where manufacturing of Induction
motors, D.C motors & Alternators with their different tests was
observed
RAJASTHAN ATOMIC POWER
STATION,RAWATBHATA,RAJASTHAN Training in ‘layout and working of electrical system' at Nuclear power
plant
Other Expertise:
· Expertise in: Auto CAD, MS office (Excel, power point, word, Visio), mind map manager, Outlook, Mathcad, document
management system., product view
DETAILS OF QUALIFICATIONS:
· B.E from NIT (REC), Jamshedpur, Ranchi University, with 69.33% marks in Electrical Engineering in 2002. (4 year
engineering course).
* PASSED THE GATE 2004 WITH 88.6 Percentile.
ACHIEVEMENT
· Passed the junior general knowledge &intelligence test held by 'CENTRAL INSTITUTE OF GENERAL KNOWLEDGE
TRAINING'
· Awarded Certificate In 'National Mathematics Olympiad Contest’ organized by 'DELHI ASSOCIATION OF
MATHEMATICS TEACHERS'`
· Stood Second Position in state level essay writing competition organized by 'ENVIRONMENT DIVISION' of Rajasthan
govt.
· Awarded Yellow Belt by 'SHOTOKAN KARATE INTERNATIONAL' affiliated to world union of karate-do organization,
Japan.
INTERESTS
· Reading Novels, Listening music, Internet surfing, playing sudoku, kakuro.
· Swimming , Driving ,Traveling, Teaching

5. ASHOK JAIN Arhus, Denmark
(Electrical) 15.12.2014
Ref: -
Karsten Roar Sorensen
Director,NPI
Tech Lead, Vestas,Denmark
M +45 22567499
KAROA@VESTAS.com

6. ASHOK JAIN Arhus, Denmark
(Electrical) 15.12.2014
Ref: -
Karsten Roar Sorensen
Director,NPI
Tech Lead, Vestas,Denmark
M +45 22567499
KAROA@VESTAS.com