The document discusses the design and performance of new replaceable coupling beams for shear wall structures, which have the ability to absorb and dissipate energy during seismic events due to their elastic and sacrificial elements. Analysis of the new coupling beams revealed that damage is focused on the replaceable 'fuse,' making repair easier compared to conventional beams that are difficult to fix after damage. The document also includes comparisons of seismic performance through static push-over analysis, demonstrating that while the new coupling beams are weaker in bearing capacity, they exhibit desirable energy-absorbing characteristics.

1. 1
P
a
g
e
|
1
Dr. Hammida

2. 2
P
a
g
e
|
2
‫الربط‬ ‫كمرة‬ ‫تكون‬ ‫ان‬ ‫يمكن‬coupling beam‫من‬
‫كانات‬ ‫مع‬ ‫وافقي‬ ‫قطري‬ ‫بشكل‬ ‫التسليح‬ ‫حديد‬
‫حديد‬Steel concrete coupling beam‫يسمى‬ ‫والذي‬Composite coupling beam‫مقطع‬ ‫استخدام‬ ‫يتم‬ ‫وعادة‬I Beam
Coupling Beams
in High-Rise Core-Wall Structures
Shear wall structures are most important lateral-force-resisting-systems that have been shown to be
very efficient in resisting seismic loads. But previous earthquake damages showed that the coupling
beams were easily damaged in the earthquake and it was often used as an energy dissipation part in
structures.

3. 3
P
a
g
e
|
3

4. 4
P
a
g
e
|
4

5. 5
P
a
g
e
|
5

6. 6
P
a
g
e
|
6

7. 7
P
a
g
e
|
7
‫المصري‬ ‫الكود‬ ‫اشتراطات‬
‫القص‬ ‫جدران‬ ‫ربط‬ ‫كمرات‬

8. 8
P
a
g
e
|
8
‫األمريكي‬ ‫الكود‬ ‫شتراطات‬‫ا‬ Aci- code

9. 9
P
a
g
e
|
9
‫ا‬‫ل‬‫ك‬‫و‬‫د‬‫ا‬‫ل‬‫س‬‫و‬‫ر‬‫ي‬‫ك‬‫م‬‫ر‬‫ا‬‫ت‬‫ر‬‫ب‬‫ط‬‫ج‬‫د‬‫ر‬‫ا‬‫ن‬‫ا‬‫ل‬‫ق‬‫ص‬
‫السوري‬ ‫الكود‬ ‫اشتراطات‬

10. 10
P
a
g
e
|
1
0
‫السوري‬ ‫الكود‬ ‫اشتراطات‬

11. 11
P
a
g
e
|
1
1
‫السوري‬ ‫الكود‬ ‫اشتراطات‬

12. 12
P
a
g
e
|
1
2
‫السوري‬ ‫الكود‬ ‫اشتراطات‬

13. 13
P
a
g
e
|
1
3
‫القصية‬ ‫الجدران‬ ‫بين‬ ‫الربط‬ ‫جوائز‬ ‫تصميم‬

14. 14
P
a
g
e
|
1
4

15. 15
P
a
g
e
|
1
5

16. 16
P
a
g
e
|
1
6

17. 17
P
a
g
e
|
1
7

18. 18
P
a
g
e
|
1
8

19. 19
P
a
g
e
|
1
9

20. 20
P
a
g
e
|
2
0

21. 21
P
a
g
e
|
2
1

22. 22
P
a
g
e
|
2
2

23. 23
P
a
g
e
|
2
3

24. 24
P
a
g
e
|
2
4

25. 25
P
a
g
e
|
2
5

26. 26
P
a
g
e
|
2
6
SUMMARY
A kind of new coupling beams had been designed to be used for shear wall structures, and the
common
characteristics of the beam was that it could be replaced after earthquake damage.
The new replaceable coupling beam was composed of elastic elementsand sacrificial elements
(may also called “fuse”). Elastic elements were made of steel reinforced concrete and sacrificial
elements, whose shape was a steel I-beam with a diamond-shaped hole in middle cross. Due to the
use of sacrificial high energy absorbing elements within these coupling beams, it could absorb and
dissipate large amounts of energy prior to its failure. Also, since these sacrificial elements were
connected toelastic elements by bolt, it could be easily replaced after damage.
In order to study the seismic performance of new replaceable coupling beams before test,
two coupled shear wall calculation models were built, of which one shear wall coupling beams was
replaceable, the other was the conventional coupling beams. Comprehensive calculation analysis
showed that the damage of the new replaceable coupling beams focused on the “fuse”, even the
elastic elements ofthe coupling beam keeping intact.
In contrast, the destruction of conventional coupling beams focused on the end, and it is difficult
to repair the damage. In addition, the four large half-scale models are being produced, to be tested
to further study the seismic performance of the new coupling beams by cyclic loading test.
Keywords: replaceable coupling beams, elastic elements, sacrificial elements, push-over analysis

27. 27
P
a
g
e
|
2
7

28. 28
P
a
g
e
|
2
8
Figure 4.2.The shear wall with replaceable coupling beams
4.2. Static push-over analysis
4.2. Static push-over analysis
For a detailed comparison of the seismic performance between conventional shear wall and new shear
wall, a static push-over analysis was carried out. An axial load of 1600kN was first applied by
prestressed rod until the axial-force-ratio reached0.28. Then, displacement controlled load was
applied until inter-story drift angles of both shear wall reached approximately 1/50. The base shear-top
displacement curves obtained from the analysis were shown in Fig. 4.3 and Fig. 4.4.
By comparing Fig. 4.9 and Fig. 4.10 can be seen, the compression wall
would bear more shear than
tension wall. Particularly the shear of the compression wall was nearly three times than tension wall in
conventional shear wall, which indicated the conventional coupling beams afford more constraint
moment to the wall limbs. In contrast, the shear of the compression wall was a little bigger than
tension wall in new shear wall, which indicatedthe replaceable coupling beams afforded weak
constraint moment to the wall limbs. Because the wall limbs size of two shear wall was the same, so,
the bearing capacity of replaceable coupling beams was weaker than the conventional coupling beams.

29. 29
P
a
g
e
|
2
9

30. 30
P
a
g
e
|
3
0

31. 31
P
a
g
e
|
3
1

32. 32
P
a
g
e
|
3
2
The efficiency of coupled wall systems to resist lateral loads is well known.
In order for the desired behavior of the coupled wall system to be
attained, the coupling beams must be sufficiently strong and stiff.
The coupling beams, however, must also yield before the wall piers, behave in a
ductile manner, and exhibit significant energy absorbing characteristics.

33. 33
P
a
g
e
|
3
3
Figure 5.Coupling beam connection to embedded steel column.

34. 34
P
a
g
e
|
3
4
CONCLUSIONS
. The coupling beams, however, must also yield before the wall
piers, behave in a ductile manner and exhibit significant energy absorbing characteristics.
This paper reviews the current state of the art for the design of conventional reinforced
concrete, diagonally reinforced concrete, steel and composite steel-concrete
coupling beams.
Although not exhaustive, critical aspects of the design of these systems are presented.
In the case of diagonally reinforced concrete coupling beams, only included in ACI
provisions for the first time in ACI 318-99,

35. 35
P
a
g
e
|
3
5
Dr. youssef Hammida