This document summarizes a student's final engineering project on optimizing wireless power transfer coils using finite element simulation. The student aims to investigate and increase the efficiency of inductive coils by optimizing their design using FEMM simulation software. Key steps include modeling coil designs in FEMM, verifying parameters in PSpice, performing mathematical calculations, and testing a practical coil model. Results show efficiency increases with frequency, with a maximum achieved. The student also explores hypotheses for multi-turn coil designs and their effects on efficiency. In conclusion, simulations, calculations, and practical testing supported optimizing coil design for wireless power transfer.
This is Part I of a four-part seminar series on New Energy. Designed for university audiences in Vietnam, we hope it has a general appeal to anyone interested in revolutionary energy solutions. Part I serves as an introduction to the seminar series, establishing the definition and nature of Zero Point Energy, and distinguishing it from mainstream "alternative energy" sources like solar and wind power. The basis of the twentieth-century secrecy regime surrounding New Energy is also discussed as a prelude to Part II, which covers the History of New Energy.
This is Part I of a four-part seminar series on New Energy. Designed for university audiences in Vietnam, we hope it has a general appeal to anyone interested in revolutionary energy solutions. Part I serves as an introduction to the seminar series, establishing the definition and nature of Zero Point Energy, and distinguishing it from mainstream "alternative energy" sources like solar and wind power. The basis of the twentieth-century secrecy regime surrounding New Energy is also discussed as a prelude to Part II, which covers the History of New Energy.
Plenary lecture given by Prof. Katsuhiko Ariga (WPI-MANA, NIMS and University of Tokyo, Japan) on September 12, 2017 in Gramado (Brazil) during the XVI B-MRS Meeting.
Esta é a primeira apresentação do Curso de Análise de Vibrações em Rolamentos que é constituído pelas seguintes partes:
1 Características das vibrações em rolamentos
2 Vibrações em rolamentos - Análise do Envelope
3 Vibrações em rolamentos - Exemplos de análise do envelope
4 Vibrações em rolamentos - Análise por Bandas
5 Vibrações em rolamentos - Exemplos de análise de vibrações em rolamentos
6 Vibrações em rolamentos - Medição de emissão acústica em rolamentos
7 Integração de tecnologias: análise de óleos e vibrações
8 Vibrações em rolamentos - Medição de tensão em veios
9 Proteção de rolamentos em motores com variadores de frequência
NANO106 is UCSD Department of NanoEngineering's core course on crystallography of materials taught by Prof Shyue Ping Ong. For more information, visit the course wiki at http://nano106.wikispaces.com.
“The goal of education is the advancement of knowledge and the dissemination of truth.”
~ John F. Kennedy.
What would you say if I told you that Perpetual Motion Machines are the most prevalent machines in the world and they are virtually everywhere from laptops to automobiles to space shuttles and everything else in between?
Depending on your level of education or indoctrination your reaction may be one of ignorant and naive indifference or ignorant albeit “educated” indignation. In either case the common denominator is always ignorance which is often mixed with emotion.
The perpetual human emotion which perpetuates the ever persistent ignorance is fear.
In fact you may already be having a Pavlovian fear based re-action to the subject – wondering if Men in Black are going to storm in at any moment and assassinate you or your career for even reading this article or entertaining an idea about one of societies greatest taboo subjects.
F.E.A.R. Is an acronym for False Evidence Appearing Real. This article will provide you with access to the truth if you are daring and open minded enough use your Reasoning Mind while keeping the fear based “fight or flight” response at bay for a few short minutes.
Two efficient algorithms for drawing accurate and beautiful phonon dispersionTakeshi Nishimatsu
Purpose: easy drawing of accurate and beautiful phonon dispersion in first-principles calculations
See also: Draw phonon dispersion of Si with Quantum Espresso https://gist.github.com/t-nissie/32c10a148a7fc054b836
Este archivo contiene algunas prácticas realizadas para la materia de control de máquinas eléctricas.
Contiene:
Arranque a tensión reducida
Frenado dinámico
Arranque de motores y relevadores
Modulación senoidal
control de motor con scr
PI con variador de frecuencia
Arranque de motores AC y CC
Variador de velocidad motor universal
Genetic Algorithm based Optimization of Machining ParametersAngshuman Pal
Optimization of a process output with reference to multiple input parameters is an important aspect of any manufacturing or machining process. This project examines and formulates a mechanism to optimize a given process output using the optimization technique of Genetic Algorithm. A new code for this purpose is formulated in MATLAB environment. The code is tested against some standardized functions and some case studies are performed to validate its performance against existing literature. The algorithm is then run over some real process performance data obtained from milling operation, and the optimum input parameters under given constraints required for achieving minimum surface roughness is proposed.
(If visualization is slow, please try downloading the file.)
Part 1 of a tutorial given in the Brazilian Physical Society meeting, ENFMC. Abstract: Density-functional theory (DFT) was developed 50 years ago, connecting fundamental quantum methods from early days of quantum mechanics to our days of computer-powered science. Today DFT is the most widely used method in electronic structure calculations. It helps moving forward materials sciences from a single atom to nanoclusters and biomolecules, connecting solid-state, quantum chemistry, atomic and molecular physics, biophysics and beyond. In this tutorial, I will try to clarify this pathway under a historical view, presenting the DFT pillars and its building blocks, namely, the Hohenberg-Kohn theorem, the Kohn-Sham scheme, the local density approximation (LDA) and generalized gradient approximation (GGA). I would like to open the black box misconception of the method, and present a more pedagogical and solid perspective on DFT.
PROJECT DESCRIPTION
DOWNLOAD
The main objective of this project is to develop a device for wireless power transfer. The concept of wireless power transfer was realized by Nikolas tesla. Wireless power transfer can make a remarkable change in the field of the electrical engineering which eliminates the use conventional copper cables and current carrying wires.
Based on this concept, the project is developed to transfer power within a small range. This project can be used for charging batteries those are physically not possible to be connected electrically such as pace makers (An electronic device that works in place of a defective heart valve) implanted in the body that runs on a battery.
The patient is required to be operated every year to replace the battery. This project is designed to charge a rechargeable battery wirelessly for the purpose. Since charging of the battery is not possible to be demonstrated, we are providing a DC fan that runs through wireless power.
This project is built upon using an electronic circuit which converts AC 230V 50Hz to AC 12V, High frequency. The output is fed to a tuned coil forming as primary of an air core transformer. The secondary coil develops a voltage of HF 12volt.
Thus the transfer of power is done by the primary(transmitter) to the secondary that is separated with a considerable distance(say 3cm). Therefore the transfer could be seen as the primary transmits and the secondary receives the power to run load.
Moreover this technique can be used in number of applications, like to charge a mobile phone, iPod, laptop battery, propeller clock wirelessly. And also this kind of charging provides a far lower risk of electrical shock as it would be galvanically isolated.
Analysis and optimization of wireless power transfer linkAjay Kumar Sah
In this paper, a high efficiency Gallium nitride (GaN), HEMT (High Electron Mobility Transistor) class-E power amplifier for the wireless power transfer link is designed and simulated on PSpice. A four-coil wireless power transfer link is modeled for maximum power transfer efficiency on ADS (Advanced Design System) and frequency splitting phenomenon is demonstrated, explained and analyzed. Two resonant coupling structures, series & mixed, are presented and compared. The efficiency performance of the link is studied using spiral and helical antennas of different wire make. In addition, techniques for improving efficiency of the wireless power transfer systems with changing coupling coefficient viz. frequency splitting phenomenon of the coils are proposed.
Plenary lecture given by Prof. Katsuhiko Ariga (WPI-MANA, NIMS and University of Tokyo, Japan) on September 12, 2017 in Gramado (Brazil) during the XVI B-MRS Meeting.
Esta é a primeira apresentação do Curso de Análise de Vibrações em Rolamentos que é constituído pelas seguintes partes:
1 Características das vibrações em rolamentos
2 Vibrações em rolamentos - Análise do Envelope
3 Vibrações em rolamentos - Exemplos de análise do envelope
4 Vibrações em rolamentos - Análise por Bandas
5 Vibrações em rolamentos - Exemplos de análise de vibrações em rolamentos
6 Vibrações em rolamentos - Medição de emissão acústica em rolamentos
7 Integração de tecnologias: análise de óleos e vibrações
8 Vibrações em rolamentos - Medição de tensão em veios
9 Proteção de rolamentos em motores com variadores de frequência
NANO106 is UCSD Department of NanoEngineering's core course on crystallography of materials taught by Prof Shyue Ping Ong. For more information, visit the course wiki at http://nano106.wikispaces.com.
“The goal of education is the advancement of knowledge and the dissemination of truth.”
~ John F. Kennedy.
What would you say if I told you that Perpetual Motion Machines are the most prevalent machines in the world and they are virtually everywhere from laptops to automobiles to space shuttles and everything else in between?
Depending on your level of education or indoctrination your reaction may be one of ignorant and naive indifference or ignorant albeit “educated” indignation. In either case the common denominator is always ignorance which is often mixed with emotion.
The perpetual human emotion which perpetuates the ever persistent ignorance is fear.
In fact you may already be having a Pavlovian fear based re-action to the subject – wondering if Men in Black are going to storm in at any moment and assassinate you or your career for even reading this article or entertaining an idea about one of societies greatest taboo subjects.
F.E.A.R. Is an acronym for False Evidence Appearing Real. This article will provide you with access to the truth if you are daring and open minded enough use your Reasoning Mind while keeping the fear based “fight or flight” response at bay for a few short minutes.
Two efficient algorithms for drawing accurate and beautiful phonon dispersionTakeshi Nishimatsu
Purpose: easy drawing of accurate and beautiful phonon dispersion in first-principles calculations
See also: Draw phonon dispersion of Si with Quantum Espresso https://gist.github.com/t-nissie/32c10a148a7fc054b836
Este archivo contiene algunas prácticas realizadas para la materia de control de máquinas eléctricas.
Contiene:
Arranque a tensión reducida
Frenado dinámico
Arranque de motores y relevadores
Modulación senoidal
control de motor con scr
PI con variador de frecuencia
Arranque de motores AC y CC
Variador de velocidad motor universal
Genetic Algorithm based Optimization of Machining ParametersAngshuman Pal
Optimization of a process output with reference to multiple input parameters is an important aspect of any manufacturing or machining process. This project examines and formulates a mechanism to optimize a given process output using the optimization technique of Genetic Algorithm. A new code for this purpose is formulated in MATLAB environment. The code is tested against some standardized functions and some case studies are performed to validate its performance against existing literature. The algorithm is then run over some real process performance data obtained from milling operation, and the optimum input parameters under given constraints required for achieving minimum surface roughness is proposed.
(If visualization is slow, please try downloading the file.)
Part 1 of a tutorial given in the Brazilian Physical Society meeting, ENFMC. Abstract: Density-functional theory (DFT) was developed 50 years ago, connecting fundamental quantum methods from early days of quantum mechanics to our days of computer-powered science. Today DFT is the most widely used method in electronic structure calculations. It helps moving forward materials sciences from a single atom to nanoclusters and biomolecules, connecting solid-state, quantum chemistry, atomic and molecular physics, biophysics and beyond. In this tutorial, I will try to clarify this pathway under a historical view, presenting the DFT pillars and its building blocks, namely, the Hohenberg-Kohn theorem, the Kohn-Sham scheme, the local density approximation (LDA) and generalized gradient approximation (GGA). I would like to open the black box misconception of the method, and present a more pedagogical and solid perspective on DFT.
PROJECT DESCRIPTION
DOWNLOAD
The main objective of this project is to develop a device for wireless power transfer. The concept of wireless power transfer was realized by Nikolas tesla. Wireless power transfer can make a remarkable change in the field of the electrical engineering which eliminates the use conventional copper cables and current carrying wires.
Based on this concept, the project is developed to transfer power within a small range. This project can be used for charging batteries those are physically not possible to be connected electrically such as pace makers (An electronic device that works in place of a defective heart valve) implanted in the body that runs on a battery.
The patient is required to be operated every year to replace the battery. This project is designed to charge a rechargeable battery wirelessly for the purpose. Since charging of the battery is not possible to be demonstrated, we are providing a DC fan that runs through wireless power.
This project is built upon using an electronic circuit which converts AC 230V 50Hz to AC 12V, High frequency. The output is fed to a tuned coil forming as primary of an air core transformer. The secondary coil develops a voltage of HF 12volt.
Thus the transfer of power is done by the primary(transmitter) to the secondary that is separated with a considerable distance(say 3cm). Therefore the transfer could be seen as the primary transmits and the secondary receives the power to run load.
Moreover this technique can be used in number of applications, like to charge a mobile phone, iPod, laptop battery, propeller clock wirelessly. And also this kind of charging provides a far lower risk of electrical shock as it would be galvanically isolated.
Analysis and optimization of wireless power transfer linkAjay Kumar Sah
In this paper, a high efficiency Gallium nitride (GaN), HEMT (High Electron Mobility Transistor) class-E power amplifier for the wireless power transfer link is designed and simulated on PSpice. A four-coil wireless power transfer link is modeled for maximum power transfer efficiency on ADS (Advanced Design System) and frequency splitting phenomenon is demonstrated, explained and analyzed. Two resonant coupling structures, series & mixed, are presented and compared. The efficiency performance of the link is studied using spiral and helical antennas of different wire make. In addition, techniques for improving efficiency of the wireless power transfer systems with changing coupling coefficient viz. frequency splitting phenomenon of the coils are proposed.
Design of wireless power transfer system via magnetic resonant coupling at 13...Ajay Kumar Sah
Design of Wireless Power Transfer System via Magnetic Resonant Coupling at 13.56MHz
Abstract: Power is a must to modern systems. Power transmission through wires is common. But not in every field can wires be used because of certain limitations. The implantable biomedical devices like pacemakers, cardiac defibrillators, and artificial hearts require power supply for long term operation. The required power is supplied by driveline cable or by battery. WPT greatly reduces the risk of infection by eliminating the driveline cable which otherwise needs to puncture the skin to provide power and also saves the valuable space inside a person’s body in case of battery powered. In such fields, what we need is wireless transmission. Wireless transmission is useful in cases where instantaneous or continuous energy transfer is needed, but interconnecting wires are inconvenient, hazardous, or impossible. In this paper, a simple design method of a wireless power transfer system using 13.56 MHz ISM band is proposed. The proposed wireless power transfer system consists of rectifier, oscillator, power amplifier, power coil, load coil and two intermediate coils as transmitter antenna and receiver antenna inserted between power coil and load coil.
This project is used to develop a wireless power transfer for vehicles without wires and connections for several applications like vehicles in stores, airports etc
Volume weight cost comparison of a 1 mva 10 kv 400v solid state against a con...Asoka Technologies
Solid-State Transformers (SSTs) are an emergent topic in the context of the Smart Grid paradigm, where SSTs could replace conventional passive transformers to add flexibility and controllability, such as power routing capabilities or reactive power compensation, to the grid. This paper presents a comparison of a 1000 kVA three-phase, low-frequency distribution transformer (LFT) and an equally rated SST, with respect to volume, weight, losses, and material costs, where the corresponding data of the SST is partly based on a full-scale prototype design. It is found that the SST’s costs are at least five times and its losses about three times higher, its weight similar but its volume reduced to less than 80 %. In addition, an AC/DC application is also considered, where the comparison turns out in favor of the SST-based concept, since its losses are only about half compared to the LFT-based system, and the volume and the weight are reduced to about one third, whereas the material costs advantage of the LFT is much less pronounced.
Today we live in a fast changing world. In present modern era power is very important role in our live system. The purpose of this paper practically implement concept of power transmission without wire. Wireless Power Transmission through inductive coupling is one of the new emerging technologies that will bring tremendous change in human life. Wireless power transfer is one of the simplest and inexpensive ways of charging as it eliminate the use of conventional copper cables and current carrying wires. Using inductive coupling concept an alternating current in transmitter coil generates a magnetic field which induces a voltage in the receiver coil. This voltage can be used to power a mobile device or charge a battery etc. Mrs. Jothy Mary Saji "Review Paper on Wireless Power Transfer" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-7 | Issue-4, August 2023, URL: https://www.ijtsrd.com/papers/ijtsrd58616.pdf Paper Url:https://www.ijtsrd.com/engineering/electronics-and-communication-engineering/58616/review-paper-on-wireless-power-transfer/mrs-jothy-mary-saji
220 kv Sub- Station By Akshit Jain Majhola Moradabad .docxAkshit Jain
industrial traing report on 220 kv sub station majhola Moradabad
With the help of this you will better understating about the power stations , its distribution and how are they working with its higher efficiency.
students can learn the operation and performance of an inverter
circuit. This senior design project aims to develop an inverter circuit experiment which addresses
several concepts and techniques used in covering DC to AC inverters.
Design and Implementation of a Programmable Bluetooth Electric Cookerijtsrd
This work focus on design and implementation of a programmable Bluetooth electric cooker. In recent times technology has been helping to improve the way we live and carry out our everyday activities. This includes the way in which we cook and prepare our foods. This improvement has been accompanied by structural developments in the use of technology characterized by the emergence of such communication protocols such as Bluetooth. This system uses an android phone with a Bluetooth device to communicate with a microcontroller which has been programmed embedded in an electric cooker. The system was tested and satisfactory results were obtained. S. O. N. Okonye | V. E Enukpere ""Design and Implementation of a Programmable Bluetooth Electric Cooker"" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-4 , June 2019, URL: https://www.ijtsrd.com/papers/ijtsrd23972.pdf
Paper URL: https://www.ijtsrd.com/engineering/electronics-and-communication-engineering/23972/design-and-implementation-of-a-programmable-bluetooth-electric-cooker/s-o-n-okonye
Similar to Bachelor- thesis, optimization of wireless power transfer coils using finite element simulation-2016 (20)
This presentation for Metal Detector System. The goal is to analyze, design, model, simulate and construct the Metal Detector System. A very simple Design Pattern was used to modulate the system with the use of less number of components. Coils were designed in consideration to the principles of induction for the Metal Detector System. Standard components were used to construct the Signal Processing Unit (ASPU). The design for the ASPU was simulated and tested using advanced simulation software called Pspice. The final Product fulfills the requirements as expected.
This report is documented for Metal Detector System. The goal is to analyze, design, model, simulate and construct the Metal Detector System. A very simple Design Pattern was used to modulate the system with the use of less number of components. Coils were designed in consideration to the principles of induction for the Metal Detector System. Standard components were used to construct the Signal Processing Unit (ASPU). The design for the ASPU was simulated and tested using advanced simulation software called Pspice. The final Product fulfills the requirements as expected.
Digital Communication and Modulation
Project 3 “Satellite Link Budgets and PE”
Arlene Meidahl - s107106 and Danish Bangash-s104712| Digital Communication | 21. maj 2015
Supervisor: John Aasted Sørensen
Finite Element Method Magnetics (FEMM) simulationDanish Bangash
Demonstration of a basic Finite Element Method Magnetics simulation program
*The demonstration is part of exam for FEMM course to operate a basic finite element simulation program took place at Denmark Technical University (2015).
The purpose of the Course DFM was to provide an overview of design for manufacturing techniques which is used to minimize the product cost through design and process improvements. It also describes and evaluates design of a new product from the prototype phase and until the mass production phase from applicable standards and regulations. And to calculate, estimate the lifetime of the electrical product, and to ensure the quality of an electric product through the production. The course leads us to explain different processes, optimum production flow based on cost, quality and high volume. This report will cover some of the major aspects, processes, and considerations for design for manufacturing.
The Automated Poker-Player System provides widely known single player poker game with all requirements and rules of original game. This game has a deck of 52 cards with 13 values each and 4 suits. The automated poker player system is implemented in the ‘C#’ programming environment platform which consist of six classes, Card, DeckOfCards, DrawCards, DealCards, HandEvaluator, and the execution class Program.cs.
Source Code: https://github.com/DanishBangash/Automated-Poker-Player
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Hybrid optimization of pumped hydro system and solar- Engr. Abdul-Azeez.pdffxintegritypublishin
Advancements in technology unveil a myriad of electrical and electronic breakthroughs geared towards efficiently harnessing limited resources to meet human energy demands. The optimization of hybrid solar PV panels and pumped hydro energy supply systems plays a pivotal role in utilizing natural resources effectively. This initiative not only benefits humanity but also fosters environmental sustainability. The study investigated the design optimization of these hybrid systems, focusing on understanding solar radiation patterns, identifying geographical influences on solar radiation, formulating a mathematical model for system optimization, and determining the optimal configuration of PV panels and pumped hydro storage. Through a comparative analysis approach and eight weeks of data collection, the study addressed key research questions related to solar radiation patterns and optimal system design. The findings highlighted regions with heightened solar radiation levels, showcasing substantial potential for power generation and emphasizing the system's efficiency. Optimizing system design significantly boosted power generation, promoted renewable energy utilization, and enhanced energy storage capacity. The study underscored the benefits of optimizing hybrid solar PV panels and pumped hydro energy supply systems for sustainable energy usage. Optimizing the design of solar PV panels and pumped hydro energy supply systems as examined across diverse climatic conditions in a developing country, not only enhances power generation but also improves the integration of renewable energy sources and boosts energy storage capacities, particularly beneficial for less economically prosperous regions. Additionally, the study provides valuable insights for advancing energy research in economically viable areas. Recommendations included conducting site-specific assessments, utilizing advanced modeling tools, implementing regular maintenance protocols, and enhancing communication among system components.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
Cosmetic shop management system project report.pdfKamal Acharya
Buying new cosmetic products is difficult. It can even be scary for those who have sensitive skin and are prone to skin trouble. The information needed to alleviate this problem is on the back of each product, but it's thought to interpret those ingredient lists unless you have a background in chemistry.
Instead of buying and hoping for the best, we can use data science to help us predict which products may be good fits for us. It includes various function programs to do the above mentioned tasks.
Data file handling has been effectively used in the program.
The automated cosmetic shop management system should deal with the automation of general workflow and administration process of the shop. The main processes of the system focus on customer's request where the system is able to search the most appropriate products and deliver it to the customers. It should help the employees to quickly identify the list of cosmetic product that have reached the minimum quantity and also keep a track of expired date for each cosmetic product. It should help the employees to find the rack number in which the product is placed.It is also Faster and more efficient way.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...Dr.Costas Sachpazis
Terzaghi's soil bearing capacity theory, developed by Karl Terzaghi, is a fundamental principle in geotechnical engineering used to determine the bearing capacity of shallow foundations. This theory provides a method to calculate the ultimate bearing capacity of soil, which is the maximum load per unit area that the soil can support without undergoing shear failure. The Calculation HTML Code included.
Sachpazis:Terzaghi Bearing Capacity Estimation in simple terms with Calculati...
Bachelor- thesis, optimization of wireless power transfer coils using finite element simulation-2016
1. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
1
Optimization of wireless power Transfer
coils using Finite Element simulation
BEng (Thesis) . Final Project
Abstract
The limit of powering devices is a huge hurdle due to the limited and unreliable wires.
Imagine a device who does not need any powering wire or even a battery, which will instead
get the power wirelessly over the air. Biometric implantations are the best example for the
current age to have the demand for such wirelessly powered devices. To make such a device
possible the transfer efficiency needs to be increased. To increase the efficiency inductor coil
needs an optimization. This is the aim of this thesis, to investigate the optimization and the
efficiency of the inductor coils using FEMM simulation software.
This report starts with historical background of Wireless Power Transfer (WPT), motivation
behind the project and the objective set to investigate efficiency and optimization WPT coils.
This report continues with a presentation of basic circuit and its theoretical framework
behind WPT, and the framework is then broken down into its basic mathematical expressions
that generates the basic variables.
Furthermore, this report covers documentation of an investigation on WPT inductor coils
using FEMM simulation software. The parameters generated from FEMM simulation models
are then, verified using Pspice simulation software for different frequency range with respect
to distance between coils.
Further, in this report the parameters generated from FEMM simulation verified by Pspice
simulations, by mathematical calculations and implementing a practical model.
Supervisor: Lars Maack
Head of studies, associate professor
Center for Bachelor of Engineering Studies
lmaa@dtu.dk
Student: Danish Bangash : s104712
BEng. Computer and Electronics Engineering
Center for Bachelor of Engineering Studies
dmab@dtu.dk
2. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
2
Dedicated
to
My Parents & my brothers
3. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
3
Table of Contents
Preface..................................................................................................................................................... 6
List of Figures ......................................................................................................................................... 7
List of Tables........................................................................................................................................... 8
List of Plots ............................................................................................................................................. 9
Chapter 1 ............................................................................................................................................... 10
Introduction ....................................................................................................................................... 10
History of wireless Power Transfer................................................................................................... 10
Motivation ......................................................................................................................................... 10
Objectives.......................................................................................................................................... 11
Organization of Thesis ...................................................................................................................... 11
Variables and Abbreviations ......................................................................................................... 11
Chapter 2 ............................................................................................................................................... 12
Introduction ....................................................................................................................................... 12
Basic Circuit...................................................................................................................................... 12
Mathematical Representation of WPT Basic Circuit ........................................................................ 13
Resistance...................................................................................................................................... 13
Inductance ..................................................................................................................................... 13
Coupling Coefficient..................................................................................................................... 14
Load Resistance............................................................................................................................. 14
Reflected Load Theory.................................................................................................................. 15
Voltage Drop across Inductor Coil................................................................................................ 15
Wireless Power Transfer Efficiency of Coils................................................................................ 15
Chapter 3 ............................................................................................................................................... 16
Implementation of practical coils before simulations........................................................................ 16
Chapter 4 ............................................................................................................................................... 18
Wireless Power Transfer modelled in Finite Element Method Magnetics (FEMM) ........................ 18
FEMM Simulation......................................................................................................................... 18
Simulation Setup ........................................................................................................................... 18
4. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
4
Simulation Results......................................................................................................................... 19
Conclusion..................................................................................................................................... 21
Chapter 5 ............................................................................................................................................... 22
Wireless Power Transfer (WPT) Pspice Verification........................................................................ 22
Simulation Setup ........................................................................................................................... 22
Simulation Results Primary Coil................................................................................................... 23
Simulation Results Secondary Coil............................................................................................... 24
Power Transfer Efficiency from Pspice perspective ..................................................................... 25
Time Domain Analysis ................................................................................................................... 26
Conclusion......................................................................................................................................... 28
Chapter 6 ............................................................................................................................................... 29
Wireless Power Transfer (WPT) FEMM Model Mathematical Verifications .................................. 29
Calculations................................................................................................................................... 29
Conclusion......................................................................................................................................... 33
Chapter 7 ............................................................................................................................................... 34
Practical Model Verification ............................................................................................................. 34
Practical Wireless Power Transfer Model Setup........................................................................... 34
Practical Model Results................................................................................................................. 34
Conclusion......................................................................................................................................... 35
Chapter 8 ............................................................................................................................................... 36
FEMM Multi turns Hypothesis for WPT Model After verifications................................................. 36
Hypothesis 1: Four turns Defined within FEMM block properties............................................... 36
Hypothesis 2: Four turns individual 6 mm wire method............................................................... 38
Hypothesis 3: Replacement; 6 mm wire by four 3 mm wires in the same 6 mm area .................. 40
Conclusion:........................................................................................................................................ 42
Chapter 9 ............................................................................................................................................... 43
Initial Conclusion .............................................................................................................................. 43
Simulations and calculations ......................................................................................................... 43
Practical Test................................................................................................................................. 43
5. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
5
Hypothesis......................................................................................................................................... 44
Final Conclusion................................................................................................................................ 44
Future Work ...................................................................................................................................... 45
Appendix............................................................................................................................................... 46
Simulation Figures Chapter 5 (Pspice).............................................................................................. 46
Simulation Figures Primary Coil................................................................................................... 46
Simulation Figures Secondary Coil............................................................................................... 47
Simulation Figures Power transfer efficiency ............................................................................... 49
Practical Model Results figures Chapter 7........................................................................................ 51
Primary Coil Scope measurements................................................................................................ 51
Secondary Coil Scope measurements with Load .......................................................................... 53
Secondary Coil Scope measurements without Load ..................................................................... 56
Bibliography...................................................................................................................................... 58
References ......................................................................................................................................... 58
Time Plan .......................................................................................................................................... 60
Matlab Scripts for FEMM Simulations............................................................................................. 62
Matlab Script for WPT model....................................................................................................... 62
Matlab Scripts for three types of hypothesis ................................................................................. 63
Pspice AC Circuits For all tested frequencies .................................................................................... 69
6. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
6
Preface
This thesis work conducted as the last part of the Bachelor of Engineering program in Computer and
Electronics Engineering at Denmark Technical University (DTU) from, 1 Feb 2016 to 7 June 2016.
An enormous amount of time and energy has been put into the investigation process, research and
studying a wide range of information around the globe. The contents of this report clarifies and
verifies the analysis of Wireless Power Transfer (WPT) coils with an assessment of its practical
applicability in terms of optimization using finite element simulation FEMM, pspice, matlab,
mathematical verification and practical coils implementation.
I would like to thank Denmark Technical University (DTU) and their authorities for providing me the
opportunity to study, BEng. Computer and Electronics program in their tremendous and outstanding
educational environment. Also giving me the opportunity to conduct my final thesis at DTU- Ballerup
Campus. It has been great pleasure to work in a professional environment.
My special thanks to Lars Maack for providing me the opportunity to work under his excellence and
tremendous supervision and providing me a project of interest. It has always been exciting to work and
have discussion on various aspects of the project. Guiding me throughout the whole session of thesis
with his feedback, advices and made sure that everything is on the right track.
7. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
7
List of Figures
Figure 2.1: Basic equivalent circuit for Wireless Power Transfer (WPT) -------------------------------- 12
Figure 2.2: Equivalent circuit for Secondary Coil (WPT) ---------------------------------------------------------------------- 14
Figure 2.3: Equivalent circuit for primary Coil (WPT) ------------------------------------------------------------------------- 15
Figure 3.1: coil design for FEMM Simulation and 6 mm semi-grid coaxial copper wire. -------------------------------- 16
Figure 3.2: coil design for FEMM Simulation and 6 mm semi-grid coaxial copper wire. -------------------------------- 17
Figure 4.1: Axisymmetric model, Primary and secondary coil Simulation setup and Practical Set ---------------------19
Figure 4.2: Axisymmetric model, Primary and secondary coil Simulation result -------------------------------------------19
Figure 5.1: Pspice AC Simulation Diagram ----------------------------------------------------------------------------------------- 22
Figure 5.2: Simulation result for Primary with Real power-peak and Vpeak-peak at 211 kHz--------------------------- 46
Figure 5.3: Simulation result for Primary with Real power-peak and Vpeak-peak at 800 kHz--------------------------- 46
Figure 5.4: Simulation result for Primary side with Real power-peak, Vpeak-peak at 4 MHz---------------------------- 46
Figure 5.5: Simulation result for Primary side with Real power-peak, Vpeak-peak at 6 MHz---------------------------- 47
Figure 5.6: Simulation result for Primary side with Real power-peak, Vpeak-peak at 10 MHz--------------------------- 47
Figure 5.7: Simulation result for Secondary side with Real power-peak, Vpeak-peak at 211 kHz
with efficient load ---------------------------------------------------------------------------------------------------------------------------47
Figure 5.8: Simulation result for Secondary side with Real power-peak, Vpeak-peak at 800 kHz
with efficient load--------------------------------------------------------------------------------------------------------------------------- 48
Figure 5.9: Simulation result for Secondary side with Real power-peak, Vpeak-peak at 4 MHz
with efficient load--------------------------------------------------------------------------------------------------------------------------- 48
Figure 5.10: Simulation result for Secondary side with Real power-peak, Vpeak-peak at 6 MHz
with efficient load-------------------------------------------------------------------------------------------------------------------------- 48
Figure 5.11: Simulation result for Secondary side with Real power-peak, Vpeak-peak at 10 MHz
with efficient load-------------------------------------------------------------------------------------------------------------------------- 49
Figure 5.12: Power efficiency of the system at 211 kHz frequency with efficient load-------------------------------------- 49
Figure 5.13: Power efficiency of the system at 800 kHz frequency with efficient load-------------------------------------- 49
Figure 5.14: Power efficiency of the system at 4 MHz frequency with efficient load---------------------------------------- 50
Figure 5.15: Power efficiency of the system at 6 MHz frequency with efficient load---------------------------------------- 50
Figure 5.16: Power efficiency of the system at 10 MHz frequency with efficient load-------------------------------------- 50
Figure 5.17: Time Domain analysis plot at 211 kHz with max efficient Load------------------------------------------------ 27
Figure 5.18: Time Domain analysis plot at 800 kHz with max efficient Load------------------------------------------------ 27
Figure 5.19: Time Domain analysis plot at 4 MHz with max efficient Load-------------------------------------------------- 27
Figure 5.20: Time Domain analysis plot at 6 MHz with max efficient Load-------------------------------------------------- 28
Figure 5.21: Time Domain analysis plot at 10 MHz with max efficient Load------------------------------------------------ 28
Figure 5.22: Pspice AC simulation Circuits for all tested frequencies--------------------------------------------------------- 69
Figure 5.23: Pspice Time Domain Simulation Circuit for all tested frequencies-------------------------------------------- 69
Figure 7.1: Voltage drop primary coil at 211 kHz frequency------------------------------------------------------------------- 51
Figure 7.2: Voltage drop primary coil at 800 kHz frequency------------------------------------------------------------------- 51
8. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
8
Figure 7.3: Voltage drop primary coil at 4 MHz frequency--------------------------------------------------------- 52
Figure 7.4: Voltage drop primary coil at 6 MHz frequency--------------------------------------------------------- 52
Figure 7.5: Voltage drop primary coil at 10 MHz frequency--------------------------------------------------------- 53
Figure 7.6: Voltage drop secondary coil at 211 kHz frequency with max efficient Load----------------------- 53
Figure 7.7: Voltage drop secondary coil at 800 kHz frequency with max efficient Load----------------------- 54
Figure 7.8: Voltage drop secondary coil at 4 MHz frequency with max efficient Load------------------------- 54
Figure 7.9: Voltage drop secondary coil at 6 MHz frequency with max efficient Load------------------------- 55
Figure 7.10: Voltage drop secondary coil at 10 MHz frequency with max efficient Load---------------------- 55
Figure 7.11: Voltage drop secondary coil at 211 kHz frequency zero load---------------------------------------- 56
Figure 7.12: Voltage drop secondary coil at 800 kHz frequency zero load---------------------------------------- 56
Figure 7.13: Voltage drop secondary coil at 4 MHz frequency zero load------------------------------------------ 57
Figure 7.14: Voltage drop secondary coil at 6 MHz frequency zero load------------------------------------------ 57
Figure 7.15: Voltage drop secondary coil at 10 MHz frequency zero load---------------------------------------- 58
Figure 8.1: Axisymmetric model Hypothesis 1, Primary and secondary coil Simulation setup--------------- 37
Figure 8.2: Axisymmetric model, Primary and secondary coil Simulation result for Hypothesis 1---------- 37
Figure 8.3: Axisymmetric model Hypothesis 2, Primary and secondary coil Simulation setup--------------- 39
Figure 8.4: Axisymmetric model, Primary and secondary coil Simulation result for Hypothesis 2---------- 39
Figure 8.5: Axisymmetric model Hypothesis 3, primary, secondary coil Simulation setup
and zoomed in primary coil------------------------------------------------------------------------------------------------- 41
Figure 8.6: Axisymmetric model, Primary and secondary coil Simulation result for Hypothesis 3 --------- 42
List of Tables
Table 1.1: Organization of thesis------------------------------------------------------------------------------------------- 11
Table 3.1: Design Limits----------------------------------------------------------------------------------------------------- 16
Table 4.1: FEMM Simulated Circuit Properties for Primary Coil at all tested frequencies------------------- 20
Table 4.2: Simulated Circuit Properties for secondary Coil at all tested frequencies--------------------------- 20
Table 5.1: Pspice AC simulation Parametric Sweep ------------------------------------------------------------------- 22
Table 5.2: Pspice AC simulation Parameters Obtained from FEMM simulation-------------------------------- 22
Table 5.3: Pspice AC Simulation circuit properties for primary coil----------------------------------------------- 23
Table 5.4: Pspice AC Simulation circuit properties for Secondary coil with max efficient Load------------- 24
Table 5.5: Pspice AC Simulation circuit properties for Secondary coil without load--------------------------- 24
Table 5.6: maximum power efficiency of the whole system with max efficient Load--------------------------- 25
Table 5.7: Pspice Time Domain analysis Load Parametric Sweep------------------------------------------------- 26
Table 5.8: Pspice Time Domain simulation Results with max efficient Load------------------------------------ 26
Table 6.1: calculation parameters from simulations for verification---------------------------------------------- 29
Table 7.1: Practical Model circuit properties for primary coil----------------------------------------------------- 34
Table 7.2: Practical Model circuit properties for Secondary coil with max efficient Load------------------- 34
Table 8.1: Hypothesis 1: Simulated Circuit Properties Primary Coil--------------------------------------------- 36
Table 8.2: Hypothesis 1: Simulated Circuit Properties for secondary Coil-------------------------------------- 36
9. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
9
Table 8.3: Hypothesis 2: Simulated Circuit Properties primary Coil--------------------------------------------- 38
Table 8.4: Hypothesis 2: Simulated Circuit Properties for single turn secondary Coil------------------------ 38
Table 8.5: Hypothesis 3: Simulated Circuit Properties for primary side----------------------------------------- 40
Table 8.6: Hypothesis 3: Simulated Circuit Properties for single turn secondary Coil------------------------ 40
List of Plots
Plot 4.1: Peak Real power of primary coil as function of all tested frequencies------------------------ 20
Plot 4.2: Voltage Drop -primary coil as function of all tested frequencies------------------------------- 21
Plot 4.3: Voltage Drop -secondary coil as function of all tested frequencies----------------------------- 21
Plot 5.1: Voltage Drop -primary coil as function all tested frequencies---------------------------------- 23
Plot 5.2: Peak Real Power- Primary coil as function all tested frequencies----------------------------- 23
Plot 5.3: Voltage Drop -Secondary coil with max efficient Load as
function all tested frequencies----------------------------------------------------------------------------------- 24
Plot 5.4: Peak Real Power –Secondary Coil with max efficient Load as
function all tested frequencies----------------------------------------------------------------------------------- 25
Plot 5.5: Efficiency as function all tested frequencies------------------------------------------------------- 25
Plot 5.6: Max efficiency Load resistance as function all tested frequencies---------------------------- 26
Plot 6.1: Efficiency as function all tested frequencies------------------------------------------------------- 33
Plot 6.2: Max efficient Load resistance as function all tested frequencies------------------------------ 33
Plot 7.1 Voltage drop primary practical measurements as function all tested frequencies--------- 35
Plot 7.2 Voltage drop secondary practical measurements as function all tested frequencies------- 35
Plot 8.1: Hypothesis 1: Voltage drop primary coil as function all tested frequencies---------------- 36
Plot 8.2: Hypothesis 2: Voltage drop primary coil as function all tested frequencies---------------- 38
Plot 8.3: Hypothesis 3: Voltage drop primary coil as function all tested frequencies---------------- 40
Plot 8.4: Hypothesis 3: peak real power primary coil as function all tested frequencies------------ 41
10. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
10
Chapter 1
Introduction
Interests for biomedical implantable devices is gaining momentum among both professionals and
research, since they offer variety of systems, Example: Automatic drug delivery, Devices to simulate
specific organs and Monitors to communicate internal vital signs to the outer world.
Though all those devices performs different tasks, one of their common issue is that of power
requirements, and it has been a researched area from past decades. This chapter introduces different
researched work in the area of wireless power transfer.
History of wireless Power Transfer
Supplying power wirelessly has been a great challenge for the scientists of the modern world through
the history of technology. Wireless power transfer is not newly emerged technology, but rather it has
been an area of interest and has been implemented and worked on since 20th
century.
Most common wireless power transfer applications by means of electromagnetic field transferring low
power known as Low Power Transmission (LPT). Over the last century, the challenge of transferring
high power at greater distances is still playing a great role of interest for the scientists, but still
implanting a practical reliable application is still pending, the reason for this is the losses associated
with greater distances.
The first practical application of wireless power transfer was, implemented in the late 1899 this
experiment was, performed by Nicola Tesla in Colorado Springs. In his experiment, he managed to
lighten up 20 incandescent lamps using Inductive Power Transfer.
Thus, several experiments has been, performed since the first Nicola tesla model.
Motivation
Transfer of wireless power has been, used since long time in biometric implants mobile phone
chargers and other short distance low power transfer using the phenomena of power transfer through
the electromagnetic field transfer.
Recently there has been a growing interest towards the innovation of a deeply challenging idea for
wireless power applications: Electronics utilities without chords. Transmission of the electrical power
utilizes it in different form of copper wires; these wires are not so reliable.
Sometimes these wires are weird especially when the apparatus is small. These wires easily gives rise
to sparking, short circuit and it may give dangerous shock. Also due to regular use of these wires, it
becomes less reliable and reduces the life span of wires. In case of biometric implants or any
application where mechanical contact is the main reason behind failure of those applications. Wireless
power transfer is the best option to overcome these types of problems.
With this type of technology, there is no longer need to worry about wires. The inventions in the area
of wireless power technology and the area of study were the motivation behind this project.
11. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
11
Objectives
The main objective of the project is to study the fundamentals of wireless power transfer in
terms of the optimization of wireless power transfer coils and the efficiency between the
transmitter and receiver coils.
Two Copper wires (Primary and Secondary) practical implementation and measurements for
comparison with Finite Element Modelling Method Simulations.
Organization of Thesis
Chapter 1 Introduction, history, motivation and research objectives, organization of thesis
Chapter 2 Basic Circuit, Mathematical representation of basic circuit.
Chapter 3 Practical coil implementation before simulations
Chapter 4 Finite Element Method Magnetics, Simulations
Chapter 5 Pspice Verification of FEMM model
Chapter 6 Mathematical Verification of FEMM model
Chapter 7 Practical Coil Measurements and Verification of FEMM model
Chapter 8 Three types of multi turn hypothesis for optimization of coils
Chapter 9 Conclusion
Appendix Simulation images, matlab scripts, practical coil images, spice simulation results
Table 1.1: Organization of thesis
Variables and Abbreviations
WPT: Wireless power Transfer
IPT: Inductive Power Transfer
PTE: Power Transfer Efficiency
RLT: Reflected Load Theory
FEMM: Finite Element Method Magnetics
PTE : Power Transfer Efficiency
FEMM: Finite Element Method Magnetics
12. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
12
Chapter 2
Introduction
Wireless power transfer (WPT) technology is also, called the inductive power transfer (IPT)
technology. It is the transmission of electrical energy from the electrical source to the electrical load
through electrical magnetic field, which eliminates the use of electrical transmission through wires.
This type of technology is very useful in those cases where the use of interconnected wires are
inconvenient and hazardous or almost impossible, wireless power transfer can be used in many
applications like biometric implants, medical sensors, or laptop chargers etc.
Indeed now a day’s wireless power transfer (WPT) used frequently in biometric implants and sensors
related to medical devices. This chapter will cover the basic circuit of wireless power transfer (WPT)
using phenomena of inductive power transmission (IPT) and related mathematical expressions that
will represent the basic circuit of wireless power transfer (WPT).
Basic Circuit
Electromagnetic induction is the phenomena behind the wireless power transfer (WPT) technology or
the inductive power transfer (IPT). [Figure 2.1] shows the basic equivalent circuit for WPT.
Figure 2.1: Basic equivalent circuit for Wireless Power Transfer (WPT)
The transfer of electrical energy via magnetic flux coupling over a large airgap between the primary
coil and the secondary coil is very weak, which results in very poor coupling factor between the
primary coil and the secondary coil.
13. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
13
Mathematical Representation of WPT Basic Circuit
In this section of the report, there will be use of [Figure 2.2] and [Figure 2.3] as equivalent circuits of
Wireless power transfer (WPT) for [Figure 2.1] in relations to the Mathematical expressions for WPT
used to derive the required parameters.
Resistance
Resistance, defined as the opposition to pass current through a conductor. Losses will always be
present when a current moves through a conductor. The power dissipated by the resistor will be in the
form of heat and given by:
Pdiss = I2
∗ R [2.1]
Series resistance of Inductor Coils
An Ideal inductor have no resistance or energy losses but in reality inductors have windings and those
windings creates resistance known as winding resistance which depends on material of wires. Since
the winding resistance appears as series with the inductor, which is often called series resistance.
AC series resistance of an inductor estimated by the product of resistivity of a conductor and length of
the conductor over the effective cross sectional area.
Rac−series =
ρl
Aeff
[2.2]
𝝆 : is the resistivity of a conductor
𝒍 : is the length of the conductor
𝑨_𝒆𝒇𝒇: is the effective cross sectional area
Where
Aeff = δπd = √
ρL
πfµ0
∗ 𝜋𝑑 [2.3]
𝛅: is the skin effect depth
µ 𝟎: is the absolute magnetic permeability of the conductor
Inductance
Inductance is a property of a conductor. Electromagnetic definition of inductance L is the ratio of
magnetic flux linkage λ to the current I
L =
λ
I
[2.4]
Inductance of Looped Coil
In electronics, inductor make use of the principle described by [2.5]. A changing current flows through
the windings of an inductor, creating a changing magnetic field. Each winding of the inductor captures
the flux and produces an induced voltage; back EMF that is self-inductance:
Lloop = N2
µ0µr (
D
2
) ∗ (ln (
8∗D
d
) − 2 [2.5]
14. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
14
Inductor Quality Factor
The inductor series resistance converts electric current through the coil into heat, which causes a loss
in inductive quality. The quality factor of an inductor is the ratio of its inductive reactance to its
resistance at a specific frequency.
Quality factor is a measure on how ideal an inductor is and defined by:
Q =
2πfL
R
[2.6]
Mutual Inductance
The mutual inductance “M” can be, expressed by:
M = K ∗ √LP ∗ LS [2.7]
Coupling Coefficient
Where “K” is the coupling coefficient between two coils primary coil, which is the transmitter, and the
secondary coil, which is the receiver can expressed by “K”.
K = √
LP
LS
∗
VS
Vp
Zero Load [2.8]
Hence LP represents the measurement inductance of the primary coil. Where as LS is the value of
measurement inductance from the secondary coil. The voltage drop across the secondary coil is VS
and the voltage drop across the primary side of the circuit represented by VP.
Load Resistance
Figure 2.2: Equivalent circuit for Secondary Coil (WPT)
[Figure 2.3] gives an overview of secondary coil components. Using reflected load theory the two
equivalent circuits are set to a frequency of operation. It assumes that the efficiency of the energy
transfer maximized, if the load resistance chosen according to [2.9]:
R 𝐿 = √(R S
)2 + (ωLS)2
[2.9]
15. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
15
Reflected Load Theory
Reflected load theory (RLT) has been widely used to analyze transformers. RLT also applied to
wireless power transfer systems. Reflected Load Theory (RLT) states that the load present in the
secondary coil affects the amount of current that flows through the primary coil. This load is not
visible to the primary coil with the same actual value of load, but instead as a function of load value of
secondary coil which is the sum of series resistance of secondary coil and load resistance of the
secondary coil. [Figure 2.3] gives an overview of the Reflected Load Theory (RLT).
R′
= (R 𝑆 + R 𝑃) ∗ k2
[2.10]
Where, RL [2.9] and K [2.8]
Thus,
R′
= [R 𝑃 + (√(R 𝑆)2 + (ωL 𝑆)2)] ∗ K2
[2.11]
Figure 2.3: Equivalent circuit for primary Coil (WPT)
Voltage Drop across Inductor Coil
Voltage drop across the coils estimated as:
V = XL ∗ I [2.12]
Where XL is inductive reactance, which is proportional to the sinusoidal signal frequency and the
inductance: Which depends on the shape of the inductor.
XL = 2πfL [2.13]
Wireless Power Transfer Efficiency of Coils
In order to calculate the efficiency of the power transfer, the theory of energy conversion is applied.
Efficiency =
Pout
Pin
=
Pout
PRs−Prim+PRs−Sec+Pout
[2.14]
16. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
16
Chapter 3
Implementation of practical coils before simulations
This chapter contains practical looped coil implementation. Practical results for both coils presented in
[Chapter 7] after obtaining the required parameters from FEMM [Chapter 4] for verification Design limit
were set to keep system small, make use of materials that are reasonable in price, available and narrow
the scope of simulations. To keep size of coils small, coil radius was limited to 17.2 cm; the thickness
of the wire is set to 6 mm in radius for both primary and secondary coils. Copper (Cu) wires used for
both coils, Copper (Cu) is known to form good inductors. Due to limitations by availability of driver
circuit for real tests, frequency is set in the range of 211 kHz - 10 MHz and peak-peak current limited
to 0.2 A. [Table 3.1] summarizes the design limits.
Coil Radius 𝟏𝟕. 𝟐 𝐜𝐦
Coil type Spherical
Wire type Semi-rigid coaxial
Wire diameter 6 mm
Wire Material Copper Cu
frequency 211 kHz – 10 MHz
Table 3.1: Design Limits
Figure 3.1: coil design for FEMM Simulation and 6 mm semi-grid coaxial copper wire.
17. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
17
Figure 3.2: coil design for FEMM Simulation and 6 mm semi-grid coaxial copper wire.
[Figure 3.1] shows actual single looped practical coil design, and its dimension.
[Figure 3.2] represents both coils at a distance of 5 cm.
18. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
18
Chapter 4
Wireless Power Transfer modelled in Finite Element Method Magnetics
(FEMM)
The simulation of Wireless power transfer model carried out in FEMM simulation software controlled
by Matlab. FEMM is a finite element method program with emphasis on magnetics, which is an ideal
program for magnetics problems before any practical implementation. Matlab is a numerical
computing environment, ideal for implementing analytical expressions and combining them into a
simulator.
The basic circuitry framework presented in [Chapter 2], a script carried out for FEMM using matlab with
different frequency starting from 211 kHz to the limit of 10 MHz with an input peak-peak current
of 0.2 A. In the sections below are the simulated results and parameters of the inductor coils, with
respect to 5 cm distance.
FEMM Simulation
Simulations carried out at different frequencies. The task for the simulation is to find required
parameters for inductor coils, which gives as big power transfer as possible at a specific frequency at
the same time keeping efficiency at reasonable levels. These parameters shows that quality factor is
dependent on the frequency, coil inductance and resistance of the coil. Coupling coefficient [2.8]
depends on inductance of primary and secondary coils, distance between primary and secondary coils
and ratio between output voltage of primary and secondary coil. Coil inductance and resistance can be
broken down to its geometrical and material properties. Parameters are coil type, coil radius, wire
radius, wire type, frequencies and material.
Simulation Setup
Model of power transfer has a symmetry along the separation axis. Therefore, coils designed as 2D-
axisymmetric. Five problems for five different frequency readings (211 kHz, 800 kHz, 4 MHz, 6
MHz, 10 MHz) are simulated. Turns ratio between primary and secondary coil is set to one. The
distance between primary coil and secondary coil is set to 5 cm. A Matlab script carried out to control
FEMM, which makes things a lot easier and quicker.
19. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
19
Figure 4.1: Axisymmetric model, Primary and secondary coil Simulation setup and Practical Set
Simulation Results
Figure 4.2: Axisymmetric model, Primary and secondary coil Simulation result
20. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
20
𝑭𝒓𝒆𝒒𝒖𝒆𝒏𝒄𝒚 𝑰 𝑷 𝑽 𝑷 𝑳 𝑷 𝑹 𝑷 𝑹𝒆𝒂𝒍 𝑷𝒐𝒘𝒆𝒓 𝒑𝒆𝒂𝒌 𝑫𝒊𝒔𝒕𝒂𝒏𝒄𝒆
𝟐𝟏𝟏 𝒌𝑯𝒛 0.2 A 0.096 V 360 nH 0.003788 Ω 75 µW 5 cm
𝟖𝟎𝟎 𝒌𝑯𝒛 0.2 A 0.36 V 359 nH 0.007403 Ω 148 µW 5 cm
𝟒 𝑴𝑯𝒛 0.2 A 1.80 V 358 nH 0.0171 Ω 342 µW 5 cm
𝟔 𝑴𝑯𝒛 0.2 A 2.70 V 358 nH 0.0211 Ω 422 µW 5 cm
𝟏𝟎 𝑴𝑯𝒛 0.2 A 4.5 V 358 nH 0.027 Ω 550 µW 5 cm
Table 4.1: FEMM Simulated Circuit Properties for Primary Coil at all tested frequencies
Frequency 𝑰 𝑺 𝑽 𝑺 𝑳 𝑺 𝑹 𝑺 𝑹𝒆𝒂𝒍 𝑷𝒐𝒘𝒆𝒓 𝒑𝒆𝒂𝒌 𝑫𝒊𝒔𝒕𝒂𝒏𝒄𝒆
𝟐𝟏𝟏 𝒌𝑯𝒛 0 A 0.019 V 360 nH 5 cm
𝟖𝟎𝟎 𝒌𝑯𝒛 0 A 0.073 V 5 cm
𝟒 𝑴𝑯𝒛 0 A 0.36 V 5 cm
𝟔 𝑴𝑯𝒛 0 A 0.55 V 5 cm
𝟏𝟎 𝑴𝑯𝒛 0 A 0.92 V 5 cm
Table 4.2: Simulated Circuit Properties for secondary Coil at all tested frequencies
Simulations made for the Wireless Power Transfer (WPT) system coils equivalent to [Figure 2.1] and.
[Figure 3.2] shows an overview of the coils setup, the disk below represents the transmitter coil (primary
coil) and the disk above represent the receiver coil (secondary coil). [Figure 4.2], [Table 4.1] and [Table 4.2]
show the results of the simulation for five frequency readings (211 kHz, 800 kHz, 4 MHz, 6 MHz, 10
MHz).
Plot 4.1: Peak Real power of primary coil as function of all tested frequencies
21. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
21
Plot 4.2: Voltage Drop -primary coil as function of all tested frequencies
Plot 4.3: Voltage Drop -secondary coil as function of all tested frequencies
Conclusion
As seen from FEMM, simulation results [Table 4.1] and [Table 4.2] when an increase in
frequency, there is an increase in voltage drop at the primary side and secondary side with
respect to distance.
In addition, there is an increase in real power when frequency is increased and series
resistance gets bigger with higher frequency.
It is obvious that real power or other parameters are not visible other than voltage drop across
secondary side. FEMM software takes secondary coil as and open circuit when there is zero
current defined for the secondary coil whilst not known. Until there is a load connected to it
and unfortunately, it is not possible to connect a load in FEMM. For that purpose, Pspice
simulation software used to verify results obtained for the primary circuit and generate the
coupling coefficient using ratio between VP and VS from FEMM simulation. In Pspice, a
dummy load connected to secondary circuit to measure power and other related parameters
associated with secondary circuit. In [Chapter 5], there will be use of derived circuit parameters
[Table 4.1] to create a model for Pspice simulations.
[Plot 4.1] gives a brief overview of real power across the primary coil at all tested frequencies
along with voltage drop across primary coil [Plot 4.2]. Which clearly indicates raise of power
across primary circuit when there is an increase in frequency. In addition, voltage drop
increases with the change in frequency across secondary coil [Plot 4.3].
22. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
22
Chapter 5
Wireless Power Transfer (WPT) Pspice Verification
In this Chapter, Pspice simulation carried out to verify the parameters generated from FEMM simulation
as discussed in [Chapter 4]. Components selection for Pspice simulation circuit are equivalent to the
parameters from FEMM with five frequency readings, each frequency reading generates their own
Parameters. An overview of the components at specific frequency is shown [Table 4.2], following with
Pspice simulation results [Table 4.3], [Table 4.4] and [Table 4.5].
Figure 5.1: Pspice AC Simulation Diagram
𝑷𝒂𝒓𝒂𝒎𝒆𝒕𝒆𝒓𝒔 𝑺𝒕𝒂𝒓𝒕 𝑽𝒂𝒍𝒖𝒆 𝑬𝒏𝒅 𝑽𝒂𝒍𝒖𝒆
𝑹_𝑳𝒐𝒂𝒅_𝟐𝟏𝟏𝒌𝑯𝒛 𝟎. 𝟑 Ω 𝟎. 𝟔 Ω
𝑹_𝑳𝒐𝒂𝒅_𝟖𝟎𝟎𝒌𝑯𝒛 𝟏. 𝟔 Ω 𝟏. 𝟗 Ω
𝑹_𝑳𝒐𝒂𝒅_𝟒𝑴𝑯𝒛 𝟖. 𝟖 Ω 𝟗. 𝟏 Ω
𝑹_𝑳𝒐𝒂𝒅_𝟔𝑴𝑯𝒛 𝟏𝟑. 𝟐 Ω 𝟏𝟑. 𝟔 Ω
𝑹_𝑳𝒐𝒂𝒅_𝟏𝟎𝑴𝑯𝒛 𝟐𝟐. 𝟐 Ω 𝟐𝟐. 𝟔 Ω
Table 5.1: Pspice AC simulation Parametric Sweep
Simulation Setup
With all components selected, the simulation circuit implemented in Pspice equivalent to [Figure 2.1] and
[Figure 3.2] and [Figure 4.1]. Setting up Vac to 0.2 A, along with a parametric sweep set to start value and end
value for load resistance [Table4.1]. [Table 4.2] gives an overview of design limits with respect to its
frequency and optimal load RL calculated by [2.9]. The parameters for the coils obtained from FEMM
simulation as discussed in [Chapter 4]
𝑭𝒓𝒆𝒒𝒖𝒆𝒏𝒄𝒚 𝑳𝒑 𝑳𝒔 𝑹𝒑 𝑹𝒔 𝑹𝑳
211 𝑘𝐻𝑧 360 nH 360 nH 0.003788 Ω 0.003788 Ω 0.5 Ω
800 𝑘𝐻𝑧 359 nH 359 nH 0.007403 Ω 0.007403 Ω 1.8 Ω
4 𝑀𝐻𝑧 358 nH 358 nH 0.0171 Ω 0.0171 Ω 9.05 Ω
6 𝑀𝐻𝑧 358 nH 358 nH 0.0211 Ω 0.0211 Ω 13.5 Ω
10 𝑀𝐻𝑧 358 nH 358 nH 0.027 Ω 0.027 Ω 22.5 Ω
Table 5.2: Pspice AC simulation Parameters Obtained from FEMM simulation
23. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
23
Simulation Results Primary Coil
In Pspice, the AC analysis carried out to study the behavior of the Primary Coil circuit. What is
important is that voltage and power behaves similar to [Table 4.1]. Comparing the results obtained from
FEMM simulation and Pspice simulation there is a slight difference in voltage drop, but the real power
in primary coil FEMM simulation matches with the real power obtained from the Pspice simulation at
the tested frequency range. [Figure 4.1] to [Figure 4.5] are the simulation plots for primary coil at frequency
range 𝟐𝟏𝟏 𝐤𝐇𝐳, 𝟖𝟎𝟎 𝐤𝐇𝐳, 𝟒 𝐌𝐇𝐳, 𝟔 𝐌𝐇𝐳 𝐚𝐧𝐝 𝟏𝟎 𝐌𝐇𝐳 [Table 5.3] is the overview of the results
obtained for primary circuit matched with FEMM simulation results in [Table 4.1].
𝑭𝒓𝒆𝒒𝒖𝒆𝒏𝒄𝒚 𝑰 𝑷 𝑽 𝑷 𝑳 𝑷 𝑹 𝑷 𝑹𝒆𝒂𝒍 𝑷𝒐𝒘𝒆𝒓 𝒑𝒆𝒂𝒌 𝑫𝒊𝒔𝒕𝒂𝒏𝒄𝒆 𝑲
𝟐𝟏𝟏 𝒌𝑯𝒛 0.2 A 0.094 V 360 nH 0.003788 Ω 75.6 µW 5 cm 0.2
𝟖𝟎𝟎 𝒌𝑯𝒛 0.2 A 0.35 V 359 nH 0.007403 Ω 148 µW 5 cm 0.2
𝟒 𝑴𝑯𝒛 0.2 A 1.80 V 358 nH 0.0171 Ω 342 µW 5 cm 0.2
𝟔 𝑴𝑯𝒛 0.2 A 2.70V 358 nH 0.0211 Ω 422 µW 5 cm 0.2
𝟏𝟎 𝑴𝑯𝒛 0.2 A 4.3 V 358 nH 0.027 Ω 540 µW 5 cm 0.2
Table 5.3: Pspice AC Simulation circuit properties for primary coil
Plot 5.1: Voltage Drop -primary coil as function all tested frequencies
Plot 5.2: Peak Real Power- Primary coil as function all tested frequencies
0,00E+00
1,00E-04
2,00E-04
3,00E-04
4,00E-04
5,00E-04
6,00E-04
2,11E+05
8,00E+05
4,00E+06
6,00E+06
1,00E+07
Realpower_Primar
y
24. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
24
Simulation Results Secondary Coil
In Pspice, the AC analysis carried out to study the behavior of the Secondary Coil circuit. What is
important is that voltage behaves similar to [Table 4.2] and the power dissipation in the secondary coil
circuit to get the power efficiency of the whole system. Comparing the Voltage drop results obtained
from FEMM simulation [Table 4.2] with Pspice simulation, there is a slight difference in voltage drop.
To obtain the real power in secondary coil a dummy load is connected to the secondary circuit,
calculated by [2.9] for 𝟐𝟏𝟏 𝐤𝐇𝐳, 𝟖𝟎𝟎 𝐤𝐇𝐳, 𝟒 𝐌𝐇𝐳, 𝟔 𝐌𝐇𝐳 𝐚𝐧𝐝 𝟏𝟎 𝐌𝐇𝐳 . [Figure 5.6] to [Figure 5.10] are
the simulation plots for secondary coil at frequency 𝟐𝟏𝟏 𝐤𝐇𝐳, 𝟖𝟎𝟎 𝐤𝐇𝐳, 𝟒 𝐌𝐇𝐳, 𝟔 𝐌𝐇𝐳 𝐚𝐧𝐝 𝟏𝟎 𝐌𝐇𝐳
[Table 5.4] gives an overview of the results obtained for secondary coil with respect to load resistance.
Frequency 𝑰 𝑺 𝑽 𝑺 𝑳 𝑺 𝑹 𝑺 + 𝑹 𝑳 𝑹𝒆𝒂𝒍 𝑷𝒐𝒘𝒆𝒓 𝒑𝒆𝒂𝒌 𝑫𝒊𝒔𝒕𝒂𝒏𝒄𝒆 𝑲
𝟐𝟏𝟏 𝒌𝑯𝒛 0A 0.014 V 360 nH 0.00378 Ω + 0.5 Ω 189 µW 5 cm 0.2
𝟖𝟎𝟎 𝒌𝑯𝒛 0 A 0.050 V 359 nH 0.007403 Ω + 1.8 Ω 718.7 µW 5 cm 0.2
𝟒 𝑴𝑯𝒛 0 A 0.3 V 358 nH 0.0171 Ω + 9.05 Ω 3.591 mW 5 cm 0.2
𝟔 𝑴𝑯𝒛 0 A 0.4 V 358 nH 0.0211 Ω + 13.5 Ω 5.41 mW 5 cm 0.2
𝟏𝟎 𝑴𝑯𝒛 0 A 0.64 V 358 nH 0.027Ω + 22.5 Ω 8.96 mW 5 cm 0.2
Table 5.4: Pspice AC Simulation circuit properties for Secondary coil with max efficient Load
Frequency 𝑰 𝑺 𝑽 𝑺 𝑳 𝑺 𝑹 𝑺 𝑹𝒆𝒂𝒍 𝑷𝒐𝒘𝒆𝒓 𝒑𝒆𝒂𝒌 𝑫𝒊𝒔𝒕𝒂𝒏𝒄𝒆 𝑲
𝟐𝟏𝟏 𝒌𝑯𝒛 0 A 0.014 V 360 nH 0.00378 Ω 1.4294 µW 5 cm 0.2
𝟖𝟎𝟎 𝒌𝑯𝒛 0 A 0.050 V 359 nH 0.007403 Ω 2.9510 µW 5 cm 0.2
𝟒 𝑴𝑯𝒛 0 A 0.3 V 358 nH 0.0171 Ω 6.8129 µW 5 cm 0.2
𝟔 𝑴𝑯𝒛 0 A 0.4 V 358 nH 0.0211 Ω 8.4546 µW 5 cm 0.2
𝟏𝟎 𝑴𝑯𝒛 0 A 0.64 V 358 nH 0.027 Ω 10.766 µW 5 cm 0.2
Table 5.5: Pspice AC Simulation circuit properties for Secondary coil without load
Plot 5.3: Voltage Drop -Secondary coil with max efficient Load as function all tested frequencies
1,00E-02
1,00E-01
1,00E+00
1,00E+05 1,00E+06 1,00E+07
V_Secondary
25. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
25
Plot 5.4: Peak Real Power –Secondary Coil with max efficient Load as function all tested frequencies
Power Transfer Efficiency from Pspice perspective
In this section of report, maximum peak power output for Wireless Power Transfer (WPT) system will
be generated and the efficiency of the system for the tested frequencies will be derived. [Table 5.6] gives
an overview of maximum peak power and its efficiency with respect to distance and load resistance
[2.9]. [Figure 5.11] to [Figure 5.15] are the Pspice simulation plots for tested frequencies.
(𝟐𝟏𝟏 𝐤𝐇𝐳, 𝟖𝟎𝟎 𝐤𝐇𝐳, 𝟒 𝐌𝐇𝐳, 𝟔 𝐌𝐇𝐳 𝐚𝐧𝐝 𝟏𝟎 𝐌𝐇𝐳).
Frequency 𝑷 𝑴𝒂𝒙−𝒑𝒆𝒂𝒌 𝜼 𝑫𝒊𝒔𝒕𝒂𝒏𝒄𝒆 𝑲 𝑹𝑳
𝟐𝟏𝟏 𝒌𝑯𝒛 710.524 mW 71 % 5 cm 0.2 0.5 Ω
𝟖𝟎𝟎 𝒌𝑯𝒛 826.130 m W 82 % 5 cm 0.2 1.8 Ω
𝟒 𝑴𝑯𝒛 911.346 mW 91 % 5 cm 0.2 9.0 Ω
𝟔 𝑴𝑯𝒛 926.290 mW 93 % 5 cm 0.2 13.5 Ω
𝟏𝟎 𝑴𝑯𝒛 942.162 mW 94 % 5 cm 0.2 22.5 Ω
Table 5.6: maximum power efficiency of the whole system with max efficient Load
Plot 5.5: Efficiency as function all tested frequencies
26. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
26
Plot 5.6: Max efficiency Load resistance as function all tested frequencies
Time Domain Analysis
Time domain simulation performed pspice to verify AC simulation in Pspice where [Table 5.7]
are the Load parameters for tested frequencies.
Time domain simulation results [Table 5.8] verifies peak real power across the load resistor
performed by Ac sweep simulation, with a minute difference which is almost neglect able
[Table 5.8] gives an overview of the peak real power result with respect to the calculated load
resistance and tested frequencies.
𝑷𝒂𝒓𝒂𝒎𝒆𝒕𝒆𝒓𝒔 𝑺𝒕𝒂𝒓𝒕 𝑽𝒂𝒍𝒖𝒆 𝑬𝒏𝒅 𝑽𝒂𝒍𝒖𝒆
𝑹_𝑳𝒐𝒂𝒅_𝟐𝟏𝟏𝒌𝑯𝒛 𝟎. 𝟑 Ω 𝟎. 𝟓 Ω
𝑹_𝑳𝒐𝒂𝒅_𝟖𝟎𝟎𝒌𝑯𝒛 𝟎. 𝟓 Ω 𝟏. 𝟖Ω
𝑹_𝑳𝒐𝒂𝒅_𝟒𝑴𝑯𝒛 𝟕. 𝟎 Ω 𝟗. 𝟎 Ω
𝑹_𝑳𝒐𝒂𝒅_𝟔𝑴𝑯𝒛 𝟖. 𝟓. Ω 𝟏𝟑. 𝟓 Ω
𝑹_𝑳𝒐𝒂𝒅_𝟏𝟎𝑴𝑯𝒛 𝟏𝟐. 𝟓 Ω 𝟐𝟐. 𝟓Ω
Table 5.7: Pspice Time Domain analysis Load Parametric Sweep
Frequency 𝑳 𝑺 𝑹 𝑺 + 𝑹 𝑳 𝑹𝒆𝒂𝒍 𝑷𝒐𝒘𝒆𝒓 𝒑𝒆𝒂𝒌 𝑫𝒊𝒔𝒕𝒂𝒏𝒄𝒆 𝑲
𝟐𝟏𝟏 𝒌𝑯𝒛 360 nH 0.00378 Ω + 0.5 Ω 186 µW 5 cm 0.2
𝟖𝟎𝟎 𝒌𝑯𝒛 359 nH 0.007403 Ω + 1.8 Ω 743.7 µW 5 cm 0.2
𝟒 𝑴𝑯𝒛 358 nH 0.0171 Ω + 9.05 Ω 3.591 mW 5 cm 0.2
𝟔 𝑴𝑯𝒛 358 nH 0.0211 Ω + 13.5 Ω 5.41 mW 5 cm 0.2
𝟏𝟎 𝑴𝑯𝒛 358 nH 0.027Ω + 22.5 Ω 8.96 mW 5 cm 0.2
Table 5.8: Pspice Time Domain simulation Results with max efficient Load
1,00E-01
1,00E+00
1,00E+01
1,00E+02
1,00E+05 1,00E+06 1,00E+07
R_Load
27. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
27
Figure 5.17: Time Domain analysis plot at 211 kHz with max efficient Load
Figure 5.18: Time Domain analysis plot at 800 kHz with max efficient Load
Figure 5.19: Time Domain analysis plot at 4 MHz with max efficient Load
28. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
28
Figure 5.20: Time Domain analysis plot at 6 MHz with max efficient Load
Figure 5.21: Time Domain analysis plot at 10 MHz with max efficient Load
Conclusion
As seen from Pspice simulation results [Table 5.3] and [Table 5.4], as there is increase in the
frequency, there is an increase in voltage drop at the primary side and the secondary side. The
results obtained from Pspice simulations verifies that FEMM simulation and Pspice simulation
has neglect able difference between the results.
In addition, there is an increase in the real power as frequency is increased and the series
resistance gets bigger with higher frequency, which verifies the results obtained from FEMM
simulation for primary coil circuit.
To see the real power on the secondary side a dummy load is connected to the secondary
circuit which is calculated by [2.9] for the tested frequencies and the load resistance parameter
is also generated by FEMM simulation. It concludes that efficiency at high frequency 10 MHz
is approx.92 % , compared to efficiency at the lowest frequency 211 kHz that is 71 % it is
clear that power transfer is more efficient when operating at high frequencies than low
frequencies [Table 5.6].
In addition, [Chapter 6] verifies simulations from FEMM and Pspice mathematically.
29. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
29
Chapter 6
Wireless Power Transfer (WPT) FEMM Model Mathematical Verifications
All parameters derived from FEMM [Chapter 4] and Pspice simulations [Chapter 5] are verified
mathematically using mathematical expressions from [Chapter 2].
Calculations
𝐹𝑟𝑒𝑞𝑢𝑒𝑛𝑐𝑦 𝑉𝑝 𝑉𝑠 𝐿𝑝 𝐿𝑠 𝑅𝑠 𝑅𝑝
211 𝑘𝐻𝑧 0.095 V 0.019 360 nH 360 nH 0.003788 Ω 0.003788 Ω
800 𝑘𝐻𝑧 0.36 V 0.073 359 nH 359 nH 0.007403 Ω 0.007403 Ω
4 𝑀𝐻𝑧 1.80 V 0.36 358 nH 358 nH 0.0171 Ω 0.0171 Ω
6 𝑀𝐻𝑧 2.70 0.55 358 nH 358 nH 0.0211 Ω 0.0211 Ω
10 𝑀𝐻𝑧 4.5 0.92 358 nH 358 nH 0.027 Ω 0.027 Ω
Table 6.1: calculation parameters from simulations for verification
Inductance of Coil
Using equation [2.3], self-inductance of coil calculated as:
Where N = 1, D = 17.2 cm, d = 6 mm, µ0 = 4 ∗ π ∗ e−7
, µr = 1
Hence
Lloop = 4 ∗ π ∗ e−7
(
17.2∗e−2
2
) ∗ (ln (
8∗17.2∗ e−2
6∗e−3
) − 2 [5.1]
Lloop = 371 nH [5.2]
Coupling Coefficient” k”
Using equation [2.8] coupling coefficient derived as:
K = (1 ∗
0.019
0.073
) ∗ 100% [5.3]
K = 0.2 = 20 % [5.4]
The results above assumes that the coupling is very low at distance of 5 cm at all tested frequencies.
Mutual Inductance” M”
Mutual inductance derived by [2.7]
M = 0.2 ∗ √371 nH ∗ 371 nH [5.3]
Where both coils have the same inductance [Table 5.1]
Therefore, the mutual inductance calculated as:
30. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
30
M = 74 nH [5.4]
Primary coil and secondary coil quality factor” Qp, Qs” for all tested frequencies
Due to both coils having same inductance and resistance, it assumes that
𝐿 𝑃 = 𝐿 𝑆 = L
And 𝑅 𝑃 = 𝑅 𝑃 = R
The quality factor for primary and secondary coil derived by [2.6] calculated as:
For 𝟐𝟏𝟏 𝐤𝐇𝐳:
Qp&s =
2∗π∗211 kHz∗371 nH
0.0034
= 144.6 [5.5]
For 𝟖𝟎𝟎 𝐤𝐇𝐳:
Qp&s =
2∗π∗800 kHz∗371 nH
0.0070
= 266.4 [5.6]
For 𝟒 𝐌𝐇𝐳:
Qp&s =
2∗π∗4 MHz∗371 nH
0.015
= 621.6 [5.7]
For 𝟔 𝐌𝐇𝐳:
Qp&s =
2∗π∗6 MHz∗371 nH
0.020
= 699.3 [5.8]
For 𝟏𝟎 𝐌𝐇𝐳:
Qp&s =
2∗π∗10 MHz∗371 nH
0.023
= 1.0𝑒3
[5.9]
Series Resistance of inductor Coils
The series resistance of coils calculated using equation [2.2] and [2.3] for all tested frequencies to verify
the simulation results [Chapter 4] and [Chapter 5].
ρ = 1.678e−8
Ωm
l = 17.2e−2
∗ pi = 54e−2
cm
µ0 = 4πe−7
H/m
For 𝟐𝟏𝟏 𝐤𝐇𝐳:
Rac−series =
(1.678𝑒−8∗54𝑒−2 )
√
1.678𝑒−8
𝜋∗211𝑒3∗(4𝑒−7∗𝜋)
∗𝜋∗6𝑒−3
= 0.0034 [5.10]
31. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
31
For 𝟖𝟎𝟎 𝐤𝐇𝐳:
Rac−series =
(1.678𝑒−8∗54𝑒−2 )
√
1.678𝑒−8
𝜋∗800𝑒3∗(4𝑒−7∗𝜋)
∗𝜋∗6𝑒−3
= 0.0070 [5.11]
For 𝟒 𝐌𝐇𝐳:
Rac−series =
(1.678𝑒−8∗54𝑒−2 )
√
1.678𝑒−8
𝜋∗4𝑒6∗(4𝑒−7∗𝜋)
∗𝜋∗6𝑒−3
= 0.0015 [5.12]
For 𝟔 𝐌𝐇𝐳:
Rac−series =
(1.678𝑒−8∗54𝑒−2 )
√
1.678𝑒−8
𝜋∗6𝑒6∗(4𝑒−7∗𝜋)
∗𝜋∗6𝑒−3
= 0.020 [5.13]
For 𝟏𝟎 𝐌𝐇𝐳:
Rac−series =
(1.678𝑒−8∗54𝑒−2 )
√
1.678𝑒−8
𝜋∗10𝑒6∗(4𝑒−7∗𝜋)
∗𝜋∗6𝑒−3
= 0.023 [5.14]
Voltage drop of inductor coil
The voltage drop across the inductor coil calculated using equation [2.12] and [2.13] for all tested
frequencies to verify the simulation results [Chapter 4] and [Chapter 5].
It is assumed that XL = RL Thus:
For 𝟐𝟏𝟏 𝐤𝐇𝐳:
Vprimary = 2 ∗ π ∗ 211 kHz ∗ 371 nH ∗ 0.2 = 0.095 V [5.15]
For 𝟖𝟎𝟎 𝐤𝐇𝐳:
Vprimary = 2 ∗ π ∗ 800 kHz ∗ 371 nH ∗ 0.2 = 0.37 V [5.16]
For 𝟒 𝐌𝐇𝐳:
Vprimary = 2 ∗ π ∗ 4 MHz ∗ 371 nH ∗ 0.2 = 1.8 V [5.17]
For 𝟔 𝐌𝐇𝐳:
Vprimary = 2 ∗ π ∗ 6 MHz ∗ 371 nH ∗ 0.2 = 2.8 V [5.18]
For 𝟏𝟎 𝐌𝐇𝐳:
Vprimary = 2 ∗ π ∗ 10 MHz ∗ 371 nH ∗ 0.2 = 4.6 V [5.19]
32. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
32
Load Resistance” RL”
Using equation [2.9], the load resistance calculated for all tested frequencies:
For 𝟐𝟏𝟏 𝐤𝐇𝐳:
RL = √(0.0034)2 + (2 ∗ π ∗ 211 kHz ∗ 371 nH)2 = 0.49 Ω [5.20]
For 𝟖𝟎𝟎 𝐤𝐇𝐳:
RL = √(0.007)2 + (2 ∗ π ∗ 800 kHz ∗ 371 nH)2 = 1.86 Ω [5.21]
For 𝟒 𝐌𝐇𝐳:
RL = √(0.015)2 + (2 ∗ π ∗ 4 MHz ∗ 371 nH)2 = 9.3 Ω [5.22]
For 𝟔 𝐌𝐇𝐳:
RL = √(0.020)2 + (2 ∗ π ∗ 6 MHz ∗ 371 nH)2 = 13.9 Ω [5.23]
For 𝟏𝟎 𝐌𝐇𝐳:
RL = √(0.023)2 + (2 ∗ π ∗ 10 MHz ∗ 371 nH)2 = 23.3 Ω [5.24]
Wireless Power Transfer Efficiency for all tested frequencies
The power efficiency of the system for all tested frequencies derived by [2.14] using peak real power
value from [Table 5.3], [Table 5.4] and [Table 5.5]
For 𝟐𝟏𝟏 𝐤𝐇𝐳:
Efficiency =
Pout
Pin
=
189 µW
75.6 µWPeak+1.4294 µW +189 µW
= 710.4 mW ∗ 100 = 71 % [5.25]
For 𝟖𝟎𝟎 𝐤𝐇𝐳:
Efficiency =
Pout
Pin
=
718.7 µW
148 µWPeak+2.9510 µW +718.7 µW
= 826.4 mW ∗ 100 = 82 % [5.26]
For 𝟒 𝐌𝐇𝐳:
Efficiency =
Pout
Pin
=
3.591 mW
342 µWPeak+6.8129 µW +3.591 mW
911.5 mW ∗ 100 = 91% [5.27]
For 𝟔 𝐌𝐇𝐳:
Efficiency =
Pout
Pin
=
5.41 mW
422 µWPeak+8.4546 µW +5.41 mW
= 926.3 mW ∗ 100 = 93% [5.28]
33. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
33
For 𝟏𝟎 𝐌𝐇𝐳:
Efficiency =
Pout
Pin
=
8.96 mW
550 µWPeak+10.766 µW +8.96 mW
= 941.1 mW ∗ 100 = 94% [5.29]
Conclusion
Plot 6.1: Efficiency as function all tested frequencies
Plot 6.2: Max efficient Load resistance as function all tested frequencies
[Plot 6.1] and [Plot 6.2] is an overview of mathematical results for all tested frequency which
verifies that the results obtained from simulations and mathematical calculation has
approximation of results to conclude that the simulations and the theoretical calculation can
have a zero difference or the difference can be neglected.
1,00E-01
1,00E+00
1,00E+01
1,00E+02
1,00E+05 1,00E+06 1,00E+07
R_Load
34. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
34
Chapter 7
Practical Model Verification
This chapter contain results of practical model WPT tests implemented in [Chapter 3] that verifies the
results obtained from FEMM simulation [Chapter 4] and pspice simulation [Chapter 5]
Practical Wireless Power Transfer Model Setup
The WPT model designed in [Chapter 3] built, and serves the source for the required measurements. The
supply voltage taken from a function generator with a current limitation of 0.2 A, and the AC signal
used to trigger at the tested frequency for 10 V peak to peak. The single looped coils were
implemented before carrying out FEMM simulations with the purpose of having a real practical model
as a prototype to simulate on using FEMM [Chapter 4]. In addition, load resistors added to the secondary
side according to the frequency of required parameters. [Table 7.1] is an overview of results obtained
from the practical model WPT along with [Table 7.2] are the results obtained for secondary coil circuit.
Practical Model Results
Primary Coil
𝑭𝒓𝒆𝒒𝒖𝒆𝒏𝒄𝒚 𝐕𝐏 𝐋 𝐏 𝐑 𝐏 𝐃𝐢𝐬𝐭𝐚𝐧𝐜𝐞 𝐊
𝟐𝟏𝟏 𝒌𝑯𝒛 0.094 V 360 nH 0.003788 Ω 5 cm 0.2
𝟖𝟎𝟎 𝒌𝑯𝒛 0.36 V 360 nH 0.007403 Ω 5 cm 0.2
𝟒 𝑴𝑯𝒛 1.80 V 360 nH 0.0171 Ω 5 cm 0.2
𝟔 𝑴𝑯𝒛 2.70 V 360 nH 0.0211 Ω 5 cm 0.2
𝟏𝟎 𝑴𝑯𝒛 4.5 V 360 nH 0.027 Ω 5 cm 0.2
Table 7.1: Practical Model circuit properties for primary coil
Secondary Coil
Frequency 𝐕𝐒 𝐋 𝐒 𝐑 𝐒+ RL 𝐃𝐢𝐬𝐭𝐚𝐧𝐜𝐞 𝐊
𝟐𝟏𝟏 𝒌𝑯𝒛 0.014 V 360nH 0.00378 Ω + 0.5 Ω 5 cm 0.2
𝟖𝟎𝟎 𝒌𝑯𝒛 0.048 V 360nH 0.007403 Ω + 1.8 Ω 5 cm 0.2
𝟒 𝑴𝑯𝒛 0.30 V 360nH 0.0171 Ω + 9.05 Ω 5 cm 0.2
𝟔 𝑴𝑯𝒛 0.39 V 360nH 0.0211 Ω + 13.5 Ω 5 cm 0.2
𝟏𝟎 𝑴𝑯𝒛 0.64 V 360nH 0.027Ω + 22.5 Ω 5 cm 0.2
Table 7.2: Practical Model circuit properties for Secondary coil with max efficient Load
35. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
35
Conclusion
Plot 7.1 Voltage drop primary practical measurements as function all tested frequencies
Plot 7.2 Voltage drop secondary practical measurements as function all tested frequencies
To conclude, practical model results [Table 7.1] and [Table 7.2] clearly indicates resemblance
between the FEMM simulations [Chapter 4] and Pspice Simulations [Chapter 5].
The scenario of practical model implementation verifies that FEMM simulation software can
give good results as in real world model before even building the real world model.
There are some deviations in practical results compared to FEMM simulation results, which
are to be expected due to the quality of materials and components used. Fine results can be
achieved by good quality of coils and other components.
1,00E-02
1,00E-01
1,00E+00
1,00E+01
1,00E+05 1,00E+06 1,00E+07
V_Primary
36. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
36
Chapter 8
FEMM Multi turns Hypothesis for WPT Model After verifications
As concluded FEMM is a valid software with respect to magnetics problems. FEMM used to perform
more experiments to make the system more efficient. Previously one turn coil were used, while
keeping one-coil turn increasing in the frequency was the conclusion to obtain better power efficiency.
Now question arises: What if the coil turns are increased while keeping frequency low?, for the sake of
argument this chapter will cover three types of hypothesis FEMM can offer for carrying out
simulations for multi turns coils. Due to lack of time, the three types of hypothesis analyzed briefly,
while keeping multi turns limited to the primary coil with respect to all tested frequencies [Table 3.1]
Hypothesis 1: Four turns Defined within FEMM block properties
𝑭𝒓𝒆𝒒𝒖𝒆𝒏𝒄𝒚 𝑰 𝑷 𝑽 𝑷 𝑳 𝑷 𝑹 𝑷 𝑹𝒆𝒂𝒍 𝑷𝒐𝒘𝒆𝒓 𝒑𝒆𝒂𝒌 𝑫𝒊𝒔𝒕𝒂𝒏𝒄𝒆
𝟐𝟏𝟏 𝒌𝑯𝒛 0.2 𝐴 1.63 𝑉 6.15 µ𝐻 0.0063 𝛺 126 µ𝑊 5 𝑐𝑚
𝟖𝟎𝟎 𝒌𝑯𝒛 0.2 𝐴 6.18 𝑉 6.15 µ𝐻 0.0066 𝛺 132 µ𝑊 5 𝑐𝑚
𝟒 𝑴𝑯𝒛 0.2 𝐴 30.9 𝑉 6.15 µ𝐻 0.0073 𝛺 147 µ𝑊 5 𝑐𝑚
𝟔 𝑴𝑯𝒛 0.2 𝐴 46.4𝑉 6.15 µ𝐻 0.0076 𝛺 153 µ𝑊 5 𝑐𝑚
𝟏𝟎 𝑴𝑯𝒛 0.2 𝐴 77.3 𝑉 6.15 µ𝐻 0.0081 𝛺 163 µ𝑊 5 𝑐𝑚
Table 8.1: Hypothesis 1: Simulated Circuit Properties Primary Coil
Frequency 𝑰 𝑺 𝑽 𝑺 𝑫𝒊𝒔𝒕𝒂𝒏𝒄𝒆
𝟐𝟏𝟏 𝒌𝑯𝒛 0.2 𝐴 0.077 𝑉 5 𝑐𝑚
𝟖𝟎𝟎 𝒌𝑯𝒛 0 𝐴 0.294 𝑉 5 𝑐𝑚
𝟒 𝑴𝑯𝒛 0 𝐴 1.5 𝑉 5 𝑐𝑚
𝟔 𝑴𝑯𝒛 0 𝐴 2.2 𝑉 5 𝑐𝑚
𝟏𝟎 𝑴𝑯𝒛 0 𝐴 3.6 𝑉 5 𝑐𝑚
Table 8.2: Hypothesis 1: Simulated Circuit Properties for secondary Coil
Plot 8.1: Hypothesis 1: Voltage drop primary coil as function all tested frequencies
1,00E+00
1,00E+01
1,00E+02
1,00E+05 1,00E+06 1,00E+07
V_Primary
37. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
37
Figure 8.1: Axisymmetric model Hypothesis 1, Primary and secondary coil Simulation setup
Figure 8.2: Axisymmetric model, Primary and secondary coil Simulation result for Hypothesis 1
[Table 8.1] shows the hypothetical results for using multi turns for WPT primary coil.
[Plot 7.1] indicates how voltage drop increases at primary when more turns added with respect to
frequency
It is not clear yet that real power is the correct power using this hypothesis. It might be the
mesh size or precision solver that not give precise power at primary side, which is lack in this
hypothesis until a deep analysis made to form precise simulation clarify the problem.
However, the rest of parameters are vital with mathematical calculations using [Chapter 2].
38. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
38
Hypothesis 2: Four turns individual 6 mm wire method
𝑭𝒓𝒆𝒒𝒖𝒆𝒏𝒄𝒚 𝑰 𝑷 𝑽 𝑷 𝑳 𝑷 𝑹 𝑷 𝑹𝒆𝒂𝒍 𝑷𝒐𝒘𝒆𝒓 𝒑𝒆𝒂𝒌 𝑫𝒊𝒔𝒕𝒂𝒏𝒄𝒆
𝟐𝟏𝟏 𝒌𝑯𝒛 0.2 𝐴 1 𝑉 4.0 µ𝐻 0.029 𝛺 591 µ𝑊 5 𝑐𝑚
𝟖𝟎𝟎 𝒌𝑯𝒛 0.2 𝐴 4 𝑉 3.9 µ𝐻 0.060 𝛺 1.2 𝑚𝑊 5 𝑐𝑚
𝟒 𝑴𝑯𝒛 0.2 𝐴 20 𝑉 3.9 µ𝐻 0.14 𝛺 2 𝑚𝑊 5 𝑐𝑚
𝟔 𝑴𝑯𝒛 0.2 A 30 V 3.9 µH 0.17 Ω 3.5 mW 5 cm
𝟏𝟎 𝑴𝑯𝒛 0.2 A 50 V 3.9 µH 0.23 Ω 4 mW 5 cm
Table 8.3: Hypothesis 2: Simulated Circuit Properties primary Coil
Frequency 𝑰 𝑺 𝑽 𝒔 𝑫𝒊𝒔𝒕𝒂𝒏𝒄𝒆
𝟐𝟏𝟏 𝒌𝑯𝒛 0.2 A 0.064 V 5 cm
𝟖𝟎𝟎 𝒌𝑯𝒛 0 A 0.24 V 5 cm
𝟒 𝑴𝑯𝒛 0 A 1.22 V 5 cm
𝟔 𝑴𝑯𝒛 0 A 1.83 V 5 cm
𝟏𝟎 𝑴𝑯𝒛 0 A 3.0 V 5 cm
Table 8.4: Hypothesis 2: Simulated Circuit Properties for single turn secondary Coil
Plot 8.2: Hypothesis 2: Voltage drop primary coil as function all tested frequencies
[Table 8.3] shows the hypothetical results for using multi turns for WPT primary coil with air gap
between wires of a coil.
[Plot 8.2] indicates how voltage drop increases at primary when the wires of a coil has gap
between them
This method can be useful only if coils are gaped mostly happened when thick wires are used
or maybe a requirement of having gap between wires of a coil then it is a useful method to
1,00E+00
1,00E+01
1,00E+02
1,00E+05 1,00E+06 1,00E+07
V_Primary
39. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
39
simulate on such gaped coils but to say that it gives a better result for such types of wires can
only be assumed.
Figure 8.3: Axisymmetric model Hypothesis 2, Primary and secondary coil Simulation setup
Figure 8.4: Axisymmetric model, Primary and secondary coil Simulation result for Hypothesis 2
40. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
40
Hypothesis 3: Replacement; 6 mm wire by four 3 mm wires in the same 6 mm area
𝑭𝒓𝒆𝒒𝒖𝒆𝒏𝒄𝒚 𝑰 𝑷 𝑽 𝑷 𝑳 𝑷 𝑹 𝑷 𝑹𝒆𝒂𝒍 𝑷𝒐𝒘𝒆𝒓 𝒑𝒆𝒂𝒌 𝑫𝒊𝒔𝒕𝒂𝒏𝒄𝒆
𝟐𝟏𝟏 𝒌𝑯𝒛 0.2 A 1.45 V 5.4 µH 0.054 Ω 1.1 mW 5 cm
𝟖𝟎𝟎 𝒌𝑯𝒛 0.2 A 5.5 V 5.4 µH 0.11 Ω 2.1 mW 5 cm
𝟒 𝑴𝑯𝒛 0.2 A 27.3 V 5.4 µH 0.24 Ω 4.8 mW 5 cm
𝟔 𝑴𝑯𝒛 0.2 A 41.0 V 5.4 µH 0.3 Ω 6.1 mW 5 cm
𝟏𝟎 𝑴𝑯𝒛 0.2 A 68.3 V 5.4 µH 0.4 Ω 7.8 mW 5 cm
Table 8.5: Hypothesis 3: Simulated Circuit Properties for primary side
Frequency 𝑰 𝑺 𝑽 𝑺 𝑫𝒊𝒔𝒕𝒂𝒏𝒄𝒆
𝟐𝟏𝟏 𝒌𝑯𝒛 0 A 0.077 V 5 cm
𝟖𝟎𝟎 𝒌𝑯𝒛 0 A 0.29 V 5 cm
𝟒 𝑴𝑯𝒛 0 A 1.47 V 5 cm
𝟔 𝑴𝑯𝒛 0 A 2.2 V 5 cm
𝟏𝟎 𝑴𝑯𝒛 0 A 3.7 V 5 cm
Table 8.6: Hypothesis 3: Simulated Circuit Properties for single turn secondary Coil
Plot 8.3: Hypothesis 3: Voltage drop primary coil as function all tested frequencies
1,00E+00
1,00E+01
1,00E+02
1,00E+05 1,00E+06 1,00E+07
V_Primary
41. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
41
Plot 8.4: Hypothesis 3: peak real power primary coil as function all tested frequencies
[Table 8.5] shows the hypothetical results for using multi turns for WPT primary coil.
[Plot 8.3] indicates how voltage drop increases at primary coils if more wires are used in same
area of WPT coil 6 mm [Figure 8.5] and [Figure 8.6] which is another way making WPT coil and in
fact it can give better and efficient results.
Due to lack of deep analysis on these phenomena, it can only be an assumption that this way
of making coils can give better results.
Figure 8.5: Axisymmetric model Hypothesis 3, primary, secondary coil Simulation setup and zoomed in primary coil
1,00E-03
1,00E-02
1,00E-01
1,00E+05 1,00E+06 1,00E+07
Real Power
42. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
42
Figure 8.6: Axisymmetric model, Primary and secondary coil Simulation result for Hypothesis 3
Conclusion:
To conclude, which one of the three types of assumptions made above is better way to
simulate on wireless power transfer coils is hard at this point until a deep analysis is carried
out, which is a project on its own. It can only be assumed that all three types of methods give
good results as looking at the simulation setups for all three types clearly indicates that it fairly
depends on the type of the coil used for WPT.
If coils are looped and tightly coupled the [Hypothesis 1], will be useful tool to simulate on such
coil and can give better and precise results according to theory [Chapter 2], which can make
system more efficient even at low frequencies.
If the wires of a coil have gap between them then [Hypothesis 2] will give good results [Table 8.3],
as seen in [Figure 8.4] those gaps can matter a lot regarding the efficiency of the system. To have
a better system minute details have to be taken into account.
In addition, if the case is that four 3 mm wires are used in same area as the single looped coil
[Figure 4.1] which is 6 mm, then [Hypothesis 3] will do the job more precisely than the two types
mentioned above.
Finally, it is all dependent on the need of the type of coils, simulations will be carried out
accordingly using FEMM simulation software and validly the results will be obtained as
expected.
43. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
43
Chapter 9
Initial Conclusion
This chapter summarizes the work done in this thesis with perspective to software, theory, practical
implementation and documentation processes and possible future work in the area of wireless power
transmission. The main conducted features related to the optimization of wireless power transfer coils
are as followed:
The wireless power transfer model extended with the theory [Chapter 2] and implemented
FEMM simulation model [Chapter 4] with actual material and geometrical properties as input
parameters [Chapter 3]. An optimization technique applied through increase in frequency.
In addition, the parameters obtained from FEMM simulation used to create the Pspice model
[Chapter 5] for verification of FEMM results and obtained real power simulation results for
secondary coil.
Verifying the result of FEMM simulation and obtaining the real power for the secondary coil
using Pspice the process extended to additional verifications of the power efficiency and other
related parameters using mathematical expression [Chapter 6] related to theoretical aspects of
wireless power transfer systems for the power transfer efficiency between both coils.
Simulations and calculations
Choosing design limits that makes the system reasonable sized coils using the geometrical and
material properties for the coils [Figure 3.1] a FEMM model simulation [Figure 4.1] carried out [Figure 4.2] for
a set of frequencies [Table 3.1] to obtain a set of optimized parameters for each of tested frequencies [Table
4.1] [Table 4.2] . A Pspice model [Figure 5.1] carried out for each frequency using parametric sweep [Table 5.1]
for load and verified FEMM simulation results obtained from FEMM simulation. In addition, power
parameters for secondary coil obtained [Table 5.4], which were not visible in FEMM simulation results
[Table 4.2] other than the voltage drop of secondary coil because FEMM considering secondary coil as
an open circuit due to zero current defined for secondary side. Power transfer efficiency for the whole
system simulated in Pspice for all tested frequencies resulting 71% for the lower frequency 211 kHz
and 94% for the highest frequency 10 MHz for a single looped coil [Table 5.6]. In addition, mathematical
calculation carried out using theoretical expressions from [Chapter 2] to verify the results obtained from
FEMM simulation and Pspice simulation theoretically [Chapter 6]. Some deviation expected between
results obtained from FEMM, Pspice and mathematical calculations, because some components
expressions were approximations. However, the similarity between the curves with respect to tested
frequencies gives FEMM simulation software validity.
Practical Test
The practical measurements will always differ from the simulations because of an approximated
practical model and difference in the load resistance calculated and the resistors obtained from
component shop at campus have a little bit of difference due to zero availability of precise
components. In [Chapter 7] it is clearly visible that even there is slight difference between the calculated
44. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
44
components and practically used components the difference in the results obtained from FEMM
simulation [Chapter 4] Pspice simulations [Chapter 5] and mathematical calculations [Chapter 6] along with the
practical measurements [Chapter 7], almost neglect able difference. Which is not much to have any sort
of impact on the results and verification of FEMM simulation; it is still valid that FEMM simulation
software is to rely on. FEMM is a lot compact, easy to use and controlled by matlab to generate plots
and other results required for magnetic problems. Although the difference can be eliminated by having
a professionally made coils by a manufacturer and precise components matching the calculated
components, which is the same as generated from FEMM simulation.
Hypothesis
Three types of hypothesis [Chapter 8] simulated in FEMM simulation after verifying the software as valid
for magnetics problems. As seen from [Chapter 8], that each of the technique hypothetically can provide a
better and efficient result for multi turn coils. It is important to take into account that if there were tight
coupling between the turns of the coil [Hypothesis 1] would be a better option to obtain better results,
which is to define the turns into the block parameters associated with FEMM software. In addition if
there is a gap between the turns due to thick wires or even thin wires but if the requirements is the gap
between the turn then [Hypothesis 2] can give a better and efficient result compared to [Hypothesis 1]. If more
wires are used in same area as single looped coil, [Figure 4.1] which is 6 mm, then [Hypothesis 3] expected
to give a precise and efficient result for simulating WPT systems in FEMM simulation software. The
reason why three types of methods [Chapter 8] are hypothesis is that due to lack of time the chances for
digging deep into those phenomena’s and analysis has been cutoff even though it’s not a project scope
but a good discussion panel in FEMM for simulating different types of coils.
The results obtained from those multi turn hypothesis [Chapter 8] clearly indicates that more turns in a
coil increases the voltage drop across the coils and so is the real power across the coils.
Final Conclusion
FEMM simulation software gives a way to optimize coils and power transfer efficiency for a system
given the design limits. Coil optimized to a specific frequency with a higher efficiency rate and higher
power transfer using single looped coil compared to lower frequencies. In that sense the objective of
the project thesis have met in all four cases FEMM simulation [Chapter 4], Pspice simulation [Chapter 5],
mathematical calculations [Chapter 6] and Practical measurements [Chapter 7]. Which verifies the fact that
FEMM simulation software is a good freeware for magnetics problems and using FEMM for further
investigation of optimization of wireless power transfer coils and the power transfer efficiency.
Pspice simulations and more deep analysis of the hypothesis can extend the work done in [Chapter 8] so
that they can be verified and will be a lot useful in future for different shapes and types of coils which
also gives a good review on FEMM being bold and open for different types of coils. However, at this
point it can only be assumed! that the three types of methods described in [Chapter 8] gives more
efficient and fine results.
45. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
45
Future Work
The model can possibly be improved by adding more turns to the coil at low frequencies due to the
fact that, qualitatively at low frequencies and within the limits increasing the number of turns N
improves Q because L varies as N2
while R varies linearly with N. Which is verified hypothetically in
[Chapter 8] that more turn can give more power, but a deep analysis is required in future to conclude the
assumptions made regarding the hypothesis carried out in [Chapter 8]. Similarly, increasing radius (r) of
the inductor improves the Q as well, because L varies as r2
and R varies linearly with r. Both of these
predictions assumes that the diameter of the coils remains the same so both predictions proportionally
uses more copper.
To obtain precise results professionally manufactured components, exact tuning as well as doing the
measurements with a network analyzer would be a good idea.
46. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
46
Appendix
Simulation Figures Chapter 5 (Pspice)
Simulation Figures Primary Coil
Figure 5.2: Simulation result for Primary with Real power-peak and Vpeak-peak at 211 kHz
Figure 5.3: Simulation result for Primary with Real power-peak and Vpeak-peak at 800 kHz
Figure 5.4: Simulation result for Primary side with Real power-peak, Vpeak-peak at 4 MHz
47. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
47
Figure 5.5: Simulation result for Primary side with Real power-peak, Vpeak-peak at 6 MHz
Figure 5.6: Simulation result for Primary side with Real power-peak, Vpeak-peak at 10 MHz
Simulation Figures Secondary Coil
Figure 5.7: Simulation result for Secondary side with Real power-peak, Vpeak-peak at 211 kHz with efficient load
48. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
48
Figure 5.8: Simulation result for Secondary side with Real power-peak, Vpeak-peak at 800 kHz with efficient load
Figure 5.9: Simulation result for Secondary side with Real power-peak, Vpeak-peak at 4 MHz with efficient load
Figure 5.10: Simulation result for Secondary side with Real power-peak, Vpeak-peak at 6 MHz with efficient load
49. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
49
Figure 5.11: Simulation result for Secondary side with Real power-peak, Vpeak-peak at 10 MHz with efficient load
Simulation Figures Power transfer efficiency
Figure 5.12: Power efficiency of the system at 211 kHz frequency with efficient load
Figure 5.13: Power efficiency of the system at 800 kHz frequency with efficient load
50. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
50
Figure 5.14: Power efficiency of the system at 4 MHz frequency with efficient load
Figure 5.15: Power efficiency of the system at 6 MHz frequency with efficient load
Figure 5.16: Power efficiency of the system at 10 MHz frequency with efficient load
51. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
51
Practical Model Results figures Chapter 7
Primary Coil Scope measurements
Figure 7.1: Voltage drop primary coil at 211 kHz frequency
Figure 7.2: Voltage drop primary coil at 800 kHz frequency
52. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
52
Figure 7.3: Voltage drop primary coil at 4 MHz frequency
Figure 7.4: Voltage drop primary coil at 6 MHz frequency
53. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
53
Figure 7.5: Voltage drop primary coil at 10 MHz frequency
Secondary Coil Scope measurements with Load
Figure 7.6: Voltage drop secondary coil at 211 kHz frequency with max efficient Load
54. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
54
Figure 7.7: Voltage drop secondary coil at 800 kHz frequency with max efficient Load
Figure 7.8: Voltage drop secondary coil at 4 MHz frequency with max efficient Load
55. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
55
Figure 7.9: Voltage drop secondary coil at 6 MHz frequency with max efficient Load
Figure 7.10: Voltage drop secondary coil at 10 MHz frequency with max efficient Load
56. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
56
Secondary Coil Scope measurements without Load
Figure 7.11: Voltage drop secondary coil at 211 kHz frequency zero load
Figure 7.12: Voltage drop secondary coil at 800 kHz frequency zero load
57. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
57
Figure 7.13: Voltage drop secondary coil at 4 MHz frequency zero load
Figure 7.14: Voltage drop secondary coil at 6 MHz frequency zero load
58. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
58
Figure 7.15: Voltage drop secondary coil at 10 MHz frequency zero load
Bibliography
James W. Nilsson Electric Circuits Fourth Edition
http://www.femm.info/Archives/doc/manual42.pdf
http://www.femm.info/Archives/doc/octavefemm.pdf
References
1) https://en.wikipedia.org/wiki/Inductor
2) http://www.witricity.com.
3) http://www.wirelesspowerconsortium.com.
4) http://olev.kaist.ac.kr/en/
5) https://en.wikipedia.org/wiki/Vacuum_permeability
6) https://www.eeweb.com/toolbox/coil-inductance/
7) https://en.wikipedia.org/wiki/Electrical_reactance
8) https://en.wikipedia.org/wiki/Magnetic_flux
9) https://en.wikibooks.org/wiki/Circuit_Theory/Inductors
10) http://www.learnabout-electronics.org/ac_theory/reactance61.php
59. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
59
11) http://meettechniek.info/passive/inductance.html
12) http://eit.lm1.dk/23434lmaweblog3901/notes/simulation-of-magnetics/femm4-2-
magnetic-simulation-examples/
13) http://www.electronics-tutorials.ws/inductor/mutual-inductance.html
14) http://www.ijritcc.org/download/1435302043.pdf
15) https://en.wikipedia.org/wiki/Copper_wire_and_cable
16) http://powerelectronics.com/alternative-energy/optimize-wireless-power-transfer-link-
efficiency-part-1
17) https://www.wirelesspowerconsortium.com/technology/quality-factor.html
18) http://www.softschools.com/formulas/physics/efficiency_formula/29/
19) http://www.allaboutcircuits.com/textbook/alternating-current/chpt-11/true-reactive-and-
apparent-power/
20) https://www.physicsforums.com/threads/how-to-calculate-resistance-inductance-
impedance-and-capacitance-of-coil-in-ac.658646/
21) http://chemandy.com/calculators/round-wire-ac-resistance-calculator.htm
22) http://www.egnret.ewg.apec.org/workshops/EVWorkshop/[2]%20Inductive-power-
transfer.pdf
60. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
60
Time Plan
Project week From
From 1st
Feb – 7th
June
Dates Phase Task
1 01-02-2016 – 05-02-2016 Research Project plan, Meeting
with LMA 01-02-2016
Project scope
discussion
2 08-02-2016 – 12-02-2016 Research Report structure,
meeting with LMA 08-
02-2016 report
discussion and project
plan
3 15-02-2016 - 19-02-2016 Project definition and
planning
Chapter 1:
Abstract, Introduction,
Report. Meeting with
LMA 15-02-2015
general discussion on
Finite Element
simulation Modeling
and circuit for
Wireless Power
Transfer (WPT
4 22-02-2016 – 26-02-2016 Project definition and
planning
Report: History of
WPT, Motivation
5 29-02-2016 – 04-03-2016 Project definition and
planning
Objectives,
Organization of thesis,
Discussion with Lars
Maack
6 07-03-2016 – 11-03-2016 Practical Model Plan
for WPT
Coil research for
primary coil (TX coil)
7 14-03-2016 – 18-03-2016 Practical Model of
WPT
Implementation of
primary coil (TX coil)
Measurements of the
primary coil using
impedance analyzer
Testing the Primary
coil measurements on
the scope
8 21-03-2016 – 25-03-2016 FEMM Model for
WPT, WPT Report
Generating FEMM
model for the primary
side for comparison
with the practical
model of primary side.
61. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
61
Report: Chapter 2
Introduction.
9 28-03-2016 – 01-04-2016 WPT Report: Basic Circuit for IPT
10 04-04-2016 – 08-04-2016 WPT Report: Mathematical
representation of basic
circuit
Meeting with Lars
Maack regarding
FEMM, report and
basic circuit
11 11-04-2016 – 15-04-2016 Practical Model for
WPT
Coil research for
secondary side,
implementation of
secondary coil.
12 18-04-2016 – 22-04-2016 Secondary Coil
Measurements
Measurements of the
secondary coil using
impedance analyzer
13 25-04-2016 – 29-04-2016 Testing Practical
Model
Time to test the
primary and secondary
coil and the transfer of
power between both
coils providing an
input from the function
generator down in the
Lab-
: A meeting with Lars
to have discussion on
the practical model.
14 02-05-2016 – 06-05-2016 Testing Practical
Model
Measurements of the
system in the Lab
15 09-05-2016 – 13-05-2016 Final FEMM model
for WPT.
Finalizing the FEMM
model for both
primary and secondary
side.
16 16-05-2016 – 20-05-2016 Comparison Comparison of the
whole System:
Mathematically,
Practically, and
FEMM simulation.
Discussion with Lars
Maack
17 23-05-2016 – 27-05-2016 Final Look up: Report,
measurements,
simulations.
Final check up on
everything.
Discussions with Lars
62. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
62
Maack would be
needed,
18 30-05-2016 – 03-06-2016 Finalizing report
19 06-05-2016 – 07-06-2016 Finalizing Project
report , delivery
Matlab Scripts for FEMM Simulations
Matlab Script for WPT model
openfemm;%opens femm
create(0);%create a new document 0 is for megnetic problem
mi_probdef(211e3,'millimeters','axi',1e-008,31,30,(0)); % Define Problem
%//////////////////////////////////////////////////////////////////////////
%////Create Outer Core////////
mi_addnode(0,-180);%--- from 0 to -180 mm y axis
mi_addnode(0,180); %--- from 0 to +180 mm y axis
mi_addsegment(0,-180,0,180); % add 360 mm of segment from -180 to 180 on y axis
mi_addarc(0,-180,0,180,180,3);
mi_addblocklabel(50,-30);
mi_selectlabel(50,-30);%---- Selcting the label
mi_setblockprop('Air',1,0,'',0,0,0);%---> defining bllock properties
mi_clearselected; %----> clear all selected items
%////////////////////////////
%//////Primary Coil////////
mi_addnode(80.5,-0);
mi_addnode(86,-0);
mi_addarc(80.5,-0,86,-0,180,1);
mi_addarc(86,-0,80.5,-0,180,1);
mi_addblocklabel(83.25,-0);
mi_selectlabel(83.25,-0);%---- Selcting the label
mi_setblockprop('Copper',1,0,'Primary Coil',0,0,1);%---> defining bllock properties
mi_clearselected; %----> clear all selected items
%///////////////////////////
%///////Secondary Coil/////
mi_addnode(80.5,50);
mi_addnode(86,50);
mi_addarc(80.5,50,86,50,180,1);
mi_addarc(86,50,80.5,50,180,1);
mi_addblocklabel(83.25,50);
mi_selectlabel(83.25,50);%---- Selcting the label
mi_setblockprop('Copper',1,0,'Secondary Coil',0,0,1);%---> defining bllock properties
mi_clearselected; %----> clear all selected items
%///////////////////////////
%////Boundary Properties////
mi_addboundprop('Boundary',0,0,0,0,0,0,0,0,3);%--->Add boudary properties
63. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
63
mi_selectarcsegment(0,-180);
mi_setarcsegmentprop(1,'Boundary',0,0);%---- Defining boundary prop to arcs
mi_clearselected;
%///////////////////////////
%///Get Materials///////////
mi_getmaterial('Air');
mi_getmaterial('Copper');
%///////////////////////////
%/////Circuit Properties////
mi_addcircprop('Primary Coil',0.2,1);
mi_addcircprop('Secondary Coil',0,1);
%///////////////////////////
mi_saveas('WirelessPowerTransferModel1.FEM');
mi_analyze(1);
mi_loadsolution;
mo_showdensityplot(1,0,6e-5,4e-10,'mag');
mo_savebitmap('Wirlesspowertransfer.bmp')
Matlab Scripts for three types of hypothesis
Hypothesis 1:
openfemm;%opens femm
create(0);%create a new document 0 is for megnetic problem
mi_probdef(211e3,'millimeters','axi',1e-008,31,30,(0)); % Define Problem
%//////////////////////////////////////////////////////////////////////////
%////Create Outer Core////////
mi_addnode(0,-180);%--- from 0 to -180 mm y axis
mi_addnode(0,180); %--- from 0 to +180 mm y axis
mi_addsegment(0,-180,0,180); % add 360 mm of segment from -180 to 180 on y axis
mi_addarc(0,-180,0,180,180,3);
mi_addblocklabel(50,-30);
mi_selectlabel(50,-30);%---- Selcting the label
mi_setblockprop('Air',1,0,'',0,0,0);%---> defining bllock properties
mi_clearselected; %----> clear all selected items
%////////////////////////////
%//////Primary Coil////////
mi_addnode(80.5,-0);
mi_addnode(86,-0);
mi_addarc(80.5,-0,86,-0,180,1);
mi_addarc(86,-0,80.5,-0,180,1);
mi_addblocklabel(83.25,-0);
mi_selectlabel(83.25,-0);%---- Selcting the label
mi_setblockprop('Copper',1,0,'Primary Coil',0,0,4);%---> defining bllock properties
64. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
64
mi_clearselected; %----> clear all selected items
%///////////////////////////
%///////Secondary Coil/////
mi_addnode(80.5,50);
mi_addnode(86,50);
mi_addarc(80.5,50,86,50,180,1);
mi_addarc(86,50,80.5,50,180,1);
mi_addblocklabel(83.25,50);
mi_selectlabel(83.25,50);%---- Selcting the label
mi_setblockprop('Copper',1,0,'Secondary Coil',0,0,1);%---> defining bllock properties
mi_clearselected; %----> clear all selected items
%///////////////////////////
%////Boundary Properties////
mi_addboundprop('Boundary',0,0,0,0,0,0,0,0,3);%--->Add boudary properties
mi_selectarcsegment(0,-180);
mi_setarcsegmentprop(1,'Boundary',0,0);%---- Defining boundary prop to arcs
mi_clearselected;
%///////////////////////////
%///Get Materials///////////
mi_getmaterial('Air');
mi_getmaterial('Copper');
%///////////////////////////
%/////Circuit Properties////
mi_addcircprop('Primary Coil',0.2,1);
mi_addcircprop('Secondary Coil',0,1);
%///////////////////////////
mi_saveas('WirelessPowerTransferModel1.FEM');
mi_analyze(1);
mi_loadsolution;
mo_showdensityplot(1,0,6e-5,4e-10,'mag');
mo_savebitmap('Wirlesspowertransfer.bmp')
65. 01-02-2016
BEng. Final Project
Wireless Power Transfer
Department of Electrical technology
DTU Diplom
Lautrupvang 15, 2750 Ballerup
65
Hypothesis 2
openfemm;%opens femm
create(0);%create a new document 0 is for megnetic problem
mi_probdef(211e3,'millimeters','axi',1e-008,31,30,(0)); % Define Problem
%//////////////////////////////////////////////////////////////////////////
%////Create Outer Core////////
mi_addnode(0,-180);%--- from 0 to -180 mm y axis
mi_addnode(0,180); %--- from 0 to +180 mm y axis
mi_addsegment(0,-180,0,180); % add 360 mm of segment from -180 to 180 on y axis
mi_addarc(0,-180,0,180,180,3);
mi_addblocklabel(50,-30);
mi_selectlabel(50,-30);%---- Selcting the label
mi_setblockprop('Air',1,0,'',0,0,0);%---> defining bllock properties
mi_clearselected; %----> clear all selected items
%////////////////////////////
%//////Primary Coil////////
mi_addnode(80.5,-0);
mi_addnode(86.5,-0);
mi_addnode(80.5,-6.25);
mi_addnode(86.5,-6.25);
mi_addnode(80.5,-12.50);
mi_addnode(86.5,-12.50);
mi_addnode(80.5,-18.75);
mi_addnode(86.5,-18.75);
mi_addarc(80.5,-0,86.5,-0,180,1);
mi_addarc(86.5,-0,80.5,-0,180,1);
mi_addarc(80.5,-6.25,86.5,-6.25,180,1);
mi_addarc(86.5,-6.25,80.5,-6.25,180,1);
mi_addarc(80.5,-12.50,86.5,-12.50,180,1);
mi_addarc(86.5,-12.50,80.5,-12.50,180,1);
mi_addarc(80.5,-18.75,86.5,-18.75,180,1);
mi_addarc(86.5,-18.75,80.5,-18.75,180,1);
mi_addblocklabel(83.25,-0);
mi_addblocklabel(83.25,-6.25);
mi_addblocklabel(83.25,-12.50);
mi_addblocklabel(83.25,-18.75);
mi_selectlabel(83.25,-0);%---- Selcting the label
mi_selectlabel(83.25,-6.25);%---- Selcting the label
mi_selectlabel(83.25,-12.50);%---- Selcting the label
mi_selectlabel(83.25,-18.75);%---- Selcting the label
mi_setblockprop('Copper',1,0,'Primary Coil',0,0,1);%---> defining bllock properties
mi_clearselected; %----> clear all selected items
%///////////////////////////
%///////Secondary Coil/////
mi_addnode(80.5,50);
mi_addnode(86,50);
mi_addarc(80.5,50,86,50,180,1);
mi_addarc(86,50,80.5,50,180,1);