direction control valve

1. APPLICATION OF DIRECTIONAL CONTROL
VALVE IN AUTOMATIC TRANSMISSION
GUIDED BY,
SRI . U.PRAKASH
(ASSOCIATE PROFESSOR
MECHANICAL
DEPARTMENT)
SUBMITTED BY,
DENY M THOMAS
121
U7
1

2. INTRODUCTION
Directional control valves
• As the name implies directional control valves are used to control the
direction of flow in a hydraulic circuit. They are used to extend, retract,
position or reciprocate hydraulic cylinder and other components for linear
motion.
• Valves contains ports that are external openings for fluid to enter and leave
via connecting pipelines
• The number of ports on a directional control valve (DCV ) is usually
identified by the term “ way”. For example, a valve with four ports is named
as four-way valve 2

3. Classification of Directional control
valves
1. According to type of construction :
• Poppet valves
• Spool valves
2. According to number of working ports :
• Two- way valves
• Three – way valves
• Four- way valves.
3. According to number of Switching position:
• Two – position
• Three – position
4. According to Actuating mechanism:
• Manual actuation
• Mechanical actuation
• Solenoid ( Electrical ) actuation
• Hydraulic ( Pilot ) actuation
• Pneumatic actuation 3

4. Poppet valves
Directional poppet valves consists of a housing bore in which one or more suitably
formed seating elements ( moveable ) in the form of balls, cones are situated.
When the operating pressure increases the valve becomes more tightly seated in
this design.
The main advantage of poppet valves are;
• No Leakage as it provides absolute sealing.
• Long useful life, as there are no leakage of oil flows.
• May be used with even the highest pressures, as no hydraulic sticking (pressure
dependent deformation ) and leakages occurs in the valve.
The disadvantages of these valves are;
• Large pressure losses due to short strokes
• Pressure collapse during switching phase due to negative overlap ( connection of
pump, actuator and tank at the same time ).
4

5. 5

6. spool valves
• The spool valve consists of a spool which is a cylindrical member that has large-
diameter lands machined to slide in a very close- fitting bore of the valve body.
• The degree of sealing depends on the size of the gap, the viscosity of the fluid and
especially on the level of pressure.
• The amount of leakage is primarily dependent on the gap between spool and
housing. Hence as the operating pressure increases the gap must be reduced or
the length of overlap increased. The radial clearance is usually less than 20 μ.
6

7. 7

8. DCV FLOW PATH TERMINOLOGY
Valve Type Valve Use
2 way On or off functions for fluid supply
3 way Single acting cylinders & uni-
directional motors
4 way Double acting cylinders, bi-directional
motors
5 way Pneumatic systems with dual air
pressure
The above description refer to the total number of directions in which a
fluid can travel through a directional control valve
8

9. DCV FLOW PATH TERMINOLOGY
• 2 POSITION
• 3 POSITION
• 4 POSITION
The positions refer to which direction the fluid happens to going when a valve is shifted
9

10. DCV SCHEMATIC SYMBOLS
The basic valve symbol is a blank envelope.
DCV ‘S have atleast two envelops which corresponds with 2 position valve.
A 3 position valve will have three envelope and so forth.
10

11. Arrows are added to indicate a direction that fluid can travel through the
valve in that position. Each arrow crossing represents two ports . The above
example indicates four ports.
11

12. 3 way valve 2 way valve
The little ‘T’ Emblem
represents blocked
port
The arrow indicate
one inlet port and
one outlet port
12

13. 4 WAY 3 POSITION DCV
The cutaway diagram shows how a spool can connect and
disconnect passages
13

14. WORKING
• If spool is shifted to right ,port A is connected to the port which is being fed
by the pump,port P. At the same time port B IS connected to the tank port T.
•The fluid from the port P flows through the port A and tank T receives the
fluid from port B
14

15. •If the spool is shifted to left ,the spool connects port P with port B , and port A
withport T which gives a reversal of the previous flow path
15

16. DCV OPERATORS
•An operator is a device that physically
moves a spool or poppet.
•Manual operators such as the push
button,handlever,and foot pedal use
human power for actuation.
•Mechanical operators use a machine
component to contact a roller or ball
bearing.
•Pilot operators use a fluid to move the
spool.
•A solenoid uses electro-mechanical force
to move a spool or poppet.
16

17. SOLENOID OPERATION
•A solenoid is an electrical-mechanical device that takes electrical energy and
produces a linear force in the direction of valve spool.
•When solenoid is energized ,the air gap is closed quickly and a force is developed
in the direction of the valve spool.
•A spring holds the spool against the solenoid push pin when the solenoid is de-
energized.
17

18. DETENTS(OPERATOR)
•Detents are used to hold a valve spool in place.
•They keep the spool from moving due to vibration or possibly from gravity where
the valve is placed in an upright position.
•The above fig shows a ball and spring type detent
18

19. SUB PLATE MOUNTED 4 WAY VALVES
•Sub plate or sub base mounting is convenient way of attaching a DCV to a
system and reducing the time required to replace it should the need arise.
•The DCV is held into place by four fasteners and a seal is made with O rings. The
time savings is in to having to remove pipe connections
19

20. PIGGY-BACK DCV
•Piggy-backing is a term used to describe two valves connected as a Unit where small
valve controls the operation of larger valve.
•This arrangement makes used of the powerful force of fluid in order to actuate a
largeflow DCV.
20

21. CENTER CONDITIONS
• OPEN CENTER
• In open- center circuit, all ports are open to each other in the center position. When the
valve is in open center position, the pump flow is directed to the tank at atmospheric
pressure.
•At the same time the actuator can be moved freely by applying an external force. Open
center valve help to prevent heat buildup.
21

22. CLOSED CENTER
•In closed center DCV all ports are closed to each other. Hence
the actuator connected to ports A and B is hydraulically locked and cannot be moved by
an external force .
•This not only waste pump design power but promotes wear and shortens pump life. Also
the temperature of oil is raised due to heat buildup in the system. This promotes oil
oxidation , viscosity drop, which further raises the wear of parts and increased leakage.
22

23. TANDEM CENTERED
• In the center configuration, the working ports A and B are blocked , and the pump
port P is connected to tank port T.
• The tandem center also results in a locked actuator . However, it also unloads the
pump at atmospheric pressure.
•The application of this design may be to hold a cylinder or fluid motor under load.23

24. FLOATING CENTERED
• In this position the pump port is blocked and the two working ports A and B are
connected to tank port T. Since the working ports A and B are connected to tank T,
the actuator can be moved freely without any external force and hence the name
floating.
•The pump produce flow at the high pressure setting of the pressure relief valve,
which builds up heat in the circuit. Hence this center configuration is used only in
special case.
24

25. APPLICATION OF CV IN AUTOMATIC
TRANSMISSION
•Control valves can also react to changes in pressure.
This simple shift valve is held at the end of its bore by spring tension and blocks the fluid
under pressure at port A.
•The larger differential area at port C is subject to governor pressure and as vehicle road
speed increases, the increasing pressure forces the valve to the left and allows fluid to flow
across from port A to port B. This can be directed to operate the next clutch or servo and
change the transmission to a higher ratio.
•As road speed falls and governor pressure diminishes, the spring moves the valve back to
cut off the fluid supply and the transmission downshifts.
25

26. APPLICATIONS IN AUTOMOTIVE AREA
• Control valves are applied in each area where hydraulic control and
actuation tasks occur.
• In the automotive area, Supply, control and regulating of actuations for
automated manual transmissions (AMT), double clutch transmissions
(DCT), continuous variable automatic transmissions (CVT) or automatic
transmissions (AT).
• Control of automated clutch actuations in hybrid drives.
• Control of differential locks.
26

27. C0NCLUSION
• Directional control valve is used to direct the supply of oil to the actuator
in a hydraulic system.
• Directional control valves are essentially used for distribution of energy in
a fluid power system. They establish the path through which a fluid
traverses a given circuit. For example they control the direction of motion
of a hydraulic cylinder or motor.
• These valves are used to control the start, stop and change in direction of
flow of pressurized fluid.
27

28. REFERENCE
• Jagadheesha T-fluid power control systems-hydraulics control in machine
tools(chpter2)
• Maher yahya sallom,Zahurrin samad-MAGNETO-RHEOLOGICAL
DIRECTIONAL CONTROL VALVE-Date:21May2011
• V.J Sonavane,T.J Rane,P.C Gawade-DESIGN AND ANALYSIS OF GLOBE VALVE
AS CONTROL VALVE USING CFD SOFTTWARE-Date:16 July 2012
28

29. THANK YOU
29