This document provides specifications for an agitator for an ash mixing tank for ITC Limited's new recovery boiler in Bhadrachalam, Andhra Pradesh, India. The agitator will mix ESP ash with black liquor in a 15 cubic meter tank. It must withstand temperatures up to 105 degrees Celsius and be resistant to black liquor which has a pH of 10-11 and viscosity of 250 Cp. The agitator shaft, impeller and other parts must be made of corrosion resistant AISI 304 stainless steel. Performance data, drawings, test certificates and manuals must be provided.
Metal Seated Ball Valves Manufacturers. Madhukar VB
Microfinish Valves Inc. manufactures various types of ball valves mainly floating ball valves, trunnion mounted ball valves. Floating ball valves come in the following varieties: forged and cast ball valves, one piece flanged
Ball valves, cast two piece, cryogenic ball valves, ASME B16.34 API 6D Floating Ball Valves, three way ball valves. for more info visit: http://www.microfinishvalvesinc.com
Metal Seated Ball Valves Manufacturers. Madhukar VB
Microfinish Valves Inc. manufactures various types of ball valves mainly floating ball valves, trunnion mounted ball valves. Floating ball valves come in the following varieties: forged and cast ball valves, one piece flanged
Ball valves, cast two piece, cryogenic ball valves, ASME B16.34 API 6D Floating Ball Valves, three way ball valves. for more info visit: http://www.microfinishvalvesinc.com
Failure Mode Analysis Of Torsion Shaft In Garrett-5 Engine Using Two Test PiecesIJERA Editor
This work deals with “Failure Analysis of Internal splines in Torsion Shaft” of “TPE 331-5-252D - GARRET ENGINE” which is used in Dornier aircraft. Garret Engine is a type of air breathing engine. It comes under the category of Turboprop engines of Gas turbine engine. As separate shafts are used for propeller and turbine, this aids them to rotate at different RPM. A torsion shaft is used to transmit the torque from main shaft to propeller shaft. Torsion shaft is used to give a deflection which is also used to measure the torque of the engine. This torsion shaft is internally connected with the main power transmission shaft and its other end is coupled to a coupler shaft with engagement of its internal splines to the external splines of coupler shaft. Further this coupler connects to the gearing system and transmits power to the propeller shaft. Due to Continues variable load over internal splines, it is subjected to high rate of wear and tear. This problem can be rectified by Failure Mode Analysis Method, in which heat treatment process of torsion shaft is being carried out. Two test pieces are heat treated separately at different temperatures of 5800C and 5400C at variable time durations. Tuffriding which is a Liquid nitriding process is done with this two test pieces and results are analyzed. The hardness of the material is increased to desired values and its life time is also increased which overcomes the problem.
1. ENMAS ANDRITZ PRIVATE LIMITED
ITC-PSPD – 400 TDS/D NEW REC. BOILER
CUSTOMER : M/s. ITC LIMITED-PSPD,
UNIT: BHADRACHALAM, ANDHRA PRADESH
PROJECT : NEW RECOVERY BOILER - 400TDS/D
SUBJECT : TECHNICAL SPECIFICATIONS FOR AMT AGITATOR
1. INTRODUCTION
Ash mixing tank agitator specified below is required for operation in chemical
recovery boiler.
2. SCOPE OF SUPPLIES
i. Complete agitator with supports, Geared motor, Coupling etc., as per the enclosed
specification.
3. SPECIFIC ASPECTS
i. SITE CONDITIONS:
a.) Mill site is situated 60 m above the MSL and temperature varies +20 to 51 OC.
b.) Seismic area classification equals to zone III as per IS 1893
c.) Power supply: 415 V +10 %, 3 Phase 50 Hz + 3 %.
ii. Geared motor drive power to be selected with adequate margin over the power
absorbed.
iii. Please quote for spares for 2 years operation with item wise price.
4. DATA / DOCUMENTS TO BE FURNISHED ( X )
ALONGWITH
Sl. No. DETAILS OF DOCUMENTS OFFER ORDER SUPPLY
3 SETS 3 SETS 6 SETS
1. DETAIL PERFORMANCE DATA X X --
2. DETAIL DIMENSIONAL DATA / CATALOGUES X -- X
3. ARRANGEMENT DRAWINGS X X --
4. MATERIAL TEST CERTIFICATE -- -- X
5. PERFORMANCE TEST, GUARANTEE CERTIFICATE -- -- X
INSTALLATION, OPERATION & MAINTENANCE
6.
MANUAL -- -- X
Name Date Job Code : BB 290 M
Prepared SMR 05.01.10 Doc No. : J/BB290M/SPECN/15
Checked SMR 05.01.10 Rev No. : 0
Approved NAP 05.01.10 Rev Date Name Description Sheet 1 of 3
H:PENGG HBOILERPROJECTITC BOOSTER
BOILERB.O.CINDENTEDAGITATORagitator_amt specn.doc
2. ENMAS ANDRITZ PRIVATE LIMITED
ITC-PSPD – 400 TDS/D NEW REC. BOILER
5. TECHNICAL DATA
TAG NUMBER 542-T-005
DESCRIPTION AMT AGITATOR ASSEMBLY
Application To mix ESP ash with Black liquor
Fluid Black liquor
Specific gravity 1.4
pH 10-11
Viscosity Cp 250
Temperature Deg C 105
Tank capacity m³ 15 (Approx)
Tank size
Dia mm 2770
Height mm 2800
Baffles 2 nos.
Type of agitator Supplier to specify
Material of construction
Shaft AISI 304
Impeller AISI 304
Rotation speed rpm Supplier to specify
Blade dia mm Supplier to specify
Shaft length mm Supplier to specify
Motor Power kW Supplier to specify
Motor Speed rpm 1500 / 1450
Dimensions of tank Attached
Propeller blades to be removable inside the tank. Agitator
Specific requirement
to have bottom guide arrangement.
Painting For Carbon steel parts like drive support etc.
Quantity No. 1 (One)
Name Date Job Code : BB 290 M
Prepared SMR 05.01.10 Doc No. : J/BB290M/SPECN/15
Checked SMR 05.01.10 Rev No. : 0
Approved NAP 05.01.10 Rev Date Name Description Sheet 2 of 3
H:PENGG HBOILERPROJECTITC BOOSTER
BOILERB.O.CINDENTEDAGITATORagitator_amt specn.doc
3. ENMAS ANDRITZ PRIVATE LIMITED
ITC-PSPD – 400 TDS/D NEW REC. BOILER
ESP ash characteristics
a) Bulk density - 80 to 100 kg/m3
b) Particle size – 5micron to 100 micron
c) Ash flow - 4.2 T/hr (approx)
d) Ash composition
Na2SO4 - 75%
NaCl -15%
Na2CO3 - 10%
Black liquor flow to AMT - 55 m3/hr
Name Date Job Code : BB 290 M
Prepared SMR 05.01.10 Doc No. : J/BB290M/SPECN/15
Checked SMR 05.01.10 Rev No. : 0
Approved NAP 05.01.10 Rev Date Name Description Sheet 3 of 3
H:PENGG HBOILERPROJECTITC BOOSTER
BOILERB.O.CINDENTEDAGITATORagitator_amt specn.doc