This document summarizes a research study that examined the use of a metal oxide semiconductor pellet sensor for detecting components of exhaled breath. Specifically, it fabricated a pellet sensor using a mixture of zinc oxide and tin oxide nanopowders. It characterized the sensor's electrical conductivity, sensitivity, response time and recovery time when exposed to exhaled breath and individual exhaled breath components at room temperature. The study found that the pellet sensor's electrical conductivity decreases when exposed to exhaled breath, and that it responds differently to different exhaled breath components. The pellet sensor shows potential for use in disease detection or quantification of exhaled breath components through non-invasive breath analysis.
This document describes the development of an enzymatic biosensing system to detect hydrogen sulfide (H2S) based on the inhibitory effect of H2S on the activity of ascorbate oxidase (AOx). Ascorbate oxidase was immobilized on a nylon membrane using glutaraldehyde. The immobilization parameters, including glutaraldehyde concentration and pH, were optimized using experimental design to achieve the fastest steady-state reaction time of 55 seconds. The biosensing system showed a linear response to H2S concentrations between 1-15 mg/L. Common ions like Fe3+ and SO42- had little effect on the sensor's ability to detect H2S. The sensor could retain
METTLER TOLEDO is the industry leader in analytical measurement solutions. Our dedication to continuously
improving the reliability and durability of our sensors, transmitters
and housings is recognized by thousands of customers. Pharmaceutical manufacturers and breweries the world over rely on our in-line dissolved oxygen systems for ensuring process safety and efficiency.
The high demand of meat causes the seller mix the fresh and not-fresh meat. Electronic nose was used to detect the quality of the meat quickly and accurately. This research is proposed to test and analyze the sensitivity of MOS sensor in the electronic nose and simulate it using Matlab to identify meat classification using neural network. Test parameters based on Indonesian National Standard (SNI 3932-2008) requirement on the quality of carcass and meat. In this simulation, the number of neurons in the hidden layer was varied to find the most accurate identification. The sensitivity analysis of the MOS sensor was conducted by testing the meat sample aroma, calculate the sensitivity, identify the formation of input, hidden layer, outputs, and simulate the result of the varied formation. Then, found the number of the most optimal neurons. The result of the data training will be applied to the real instrument.
Predictive Model for Corrosion Inhibition of Mild Steel in HCl by Crushed Lea...IRJET Journal
The document presents a study on using crushed leaves of the Clerodendrum Splendens plant as a natural corrosion inhibitor for mild steel immersed in hydrochloric acid solutions. Key findings from the study include:
1) The crushed leaves reduced the corrosion rate of mild steel and improved inhibition efficiency as exposure time and leaf quantity increased, with the highest efficiency of 70.7% achieved.
2) A predictive corrosion model was developed using multiple regression and artificial neural networks to predict corrosion rates based on time, acid concentration, and leaf quantity.
3) Analysis of the steel surface suggested the leaves form a protective film associated with functional groups that inhibit corrosion.
Dynamic Stand-Alone Gas Detection SystemIRJET Journal
This document summarizes a dynamic stand-alone gas detection system designed by R.G. Dhokte and Dr. M.H. Nerkar. The system aims to flexibly detect and monitor concentrations of toxic and combustible gases like carbon monoxide, LPG and methane using low-cost sensors. An AVR microcontroller and GSM module allow for control and communication. Compared to standard systems, the results from this system's sensors are approximately equal while being more cost-effective. The system requires 16-22 minutes to provide detection results.
The effect of ethanol extract of leaves of Conyza Dicorides plant on the corrosion inhibition
of mild steel in 1M HCl solution was investigated by weight loss and electrochemical polarization
techniques at temperature range (25–65 ̊C). The Results obtained showed that the percentage
inhibition efficiency increases with the increasing of inhibitor concentration and decreases with the
increasing of temperature. At a concentration of 2 g/L, the percentage inhibition efficiency reached
about (94.87%) at 25 ̊C. The thermodynamic activation functions of dissolution process and
adsorption parameters were calculated and discussed. Adsorption of the additive was found to follow
the Langmuir adsorption isotherm.
1. The document describes a novel technique for glucose sensing using a thin film made of collagen and zinc oxide nanoparticles.
2. Zinc oxide is synthesized using two methods, in ethylenediol medium and water medium, and characterized using FTIR and FT-Raman spectroscopy.
3. A glucose biosensor is created using the zinc oxide collagen thin film, with copper and tin electrodes. Testing shows it can distinguish between low and high glucose concentrations based on electrical output.
Monitoring Industrial Combustion Through Automotive Oxygen Sensordrboon
The monitoring of oxygen percentage in flue gases is one of various ways of controlling efficiency and emissions of industrial combustion. In general, flue gases analyzers are expensive and not accessible to small scale industries. The automotive Lambda sensor is an oxygen sensor which controls the electronic injection of the modern internal combustion vehicles. The aim of this study is to present two methods of measuring the oxygen concentration in flue gases of industrial combustion by the use of the automotive Lambda sensor. One method uses the voltage signals of a heated Lambda sensor and the other one uses the Current Reversal Mode (CRM) of operation of such sensor. Results presented in this article show that such methods are effective to control industrial combustion.
This document describes the development of an enzymatic biosensing system to detect hydrogen sulfide (H2S) based on the inhibitory effect of H2S on the activity of ascorbate oxidase (AOx). Ascorbate oxidase was immobilized on a nylon membrane using glutaraldehyde. The immobilization parameters, including glutaraldehyde concentration and pH, were optimized using experimental design to achieve the fastest steady-state reaction time of 55 seconds. The biosensing system showed a linear response to H2S concentrations between 1-15 mg/L. Common ions like Fe3+ and SO42- had little effect on the sensor's ability to detect H2S. The sensor could retain
METTLER TOLEDO is the industry leader in analytical measurement solutions. Our dedication to continuously
improving the reliability and durability of our sensors, transmitters
and housings is recognized by thousands of customers. Pharmaceutical manufacturers and breweries the world over rely on our in-line dissolved oxygen systems for ensuring process safety and efficiency.
The high demand of meat causes the seller mix the fresh and not-fresh meat. Electronic nose was used to detect the quality of the meat quickly and accurately. This research is proposed to test and analyze the sensitivity of MOS sensor in the electronic nose and simulate it using Matlab to identify meat classification using neural network. Test parameters based on Indonesian National Standard (SNI 3932-2008) requirement on the quality of carcass and meat. In this simulation, the number of neurons in the hidden layer was varied to find the most accurate identification. The sensitivity analysis of the MOS sensor was conducted by testing the meat sample aroma, calculate the sensitivity, identify the formation of input, hidden layer, outputs, and simulate the result of the varied formation. Then, found the number of the most optimal neurons. The result of the data training will be applied to the real instrument.
Predictive Model for Corrosion Inhibition of Mild Steel in HCl by Crushed Lea...IRJET Journal
The document presents a study on using crushed leaves of the Clerodendrum Splendens plant as a natural corrosion inhibitor for mild steel immersed in hydrochloric acid solutions. Key findings from the study include:
1) The crushed leaves reduced the corrosion rate of mild steel and improved inhibition efficiency as exposure time and leaf quantity increased, with the highest efficiency of 70.7% achieved.
2) A predictive corrosion model was developed using multiple regression and artificial neural networks to predict corrosion rates based on time, acid concentration, and leaf quantity.
3) Analysis of the steel surface suggested the leaves form a protective film associated with functional groups that inhibit corrosion.
Dynamic Stand-Alone Gas Detection SystemIRJET Journal
This document summarizes a dynamic stand-alone gas detection system designed by R.G. Dhokte and Dr. M.H. Nerkar. The system aims to flexibly detect and monitor concentrations of toxic and combustible gases like carbon monoxide, LPG and methane using low-cost sensors. An AVR microcontroller and GSM module allow for control and communication. Compared to standard systems, the results from this system's sensors are approximately equal while being more cost-effective. The system requires 16-22 minutes to provide detection results.
The effect of ethanol extract of leaves of Conyza Dicorides plant on the corrosion inhibition
of mild steel in 1M HCl solution was investigated by weight loss and electrochemical polarization
techniques at temperature range (25–65 ̊C). The Results obtained showed that the percentage
inhibition efficiency increases with the increasing of inhibitor concentration and decreases with the
increasing of temperature. At a concentration of 2 g/L, the percentage inhibition efficiency reached
about (94.87%) at 25 ̊C. The thermodynamic activation functions of dissolution process and
adsorption parameters were calculated and discussed. Adsorption of the additive was found to follow
the Langmuir adsorption isotherm.
1. The document describes a novel technique for glucose sensing using a thin film made of collagen and zinc oxide nanoparticles.
2. Zinc oxide is synthesized using two methods, in ethylenediol medium and water medium, and characterized using FTIR and FT-Raman spectroscopy.
3. A glucose biosensor is created using the zinc oxide collagen thin film, with copper and tin electrodes. Testing shows it can distinguish between low and high glucose concentrations based on electrical output.
Monitoring Industrial Combustion Through Automotive Oxygen Sensordrboon
The monitoring of oxygen percentage in flue gases is one of various ways of controlling efficiency and emissions of industrial combustion. In general, flue gases analyzers are expensive and not accessible to small scale industries. The automotive Lambda sensor is an oxygen sensor which controls the electronic injection of the modern internal combustion vehicles. The aim of this study is to present two methods of measuring the oxygen concentration in flue gases of industrial combustion by the use of the automotive Lambda sensor. One method uses the voltage signals of a heated Lambda sensor and the other one uses the Current Reversal Mode (CRM) of operation of such sensor. Results presented in this article show that such methods are effective to control industrial combustion.
Study of cigarette butts extract as corrosiveinhibiting agent in j55 steel ma...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Study of cigarette butts extract as corrosiveinhibiting agent in j55 steel ma...eSAT Journals
This document summarizes a study on using extracts from cigarette butts as a corrosion inhibitor for J55 steel. Weight loss tests and electrochemical techniques showed the cigarette butt extract inhibited corrosion of J55 steel in 15% hydrochloric acid solution. The highest inhibition efficiencies were 99% at 30°C and 61% at 105°C using a 6% concentration of the extract. Scanning electron microscopy confirmed the extract protected the steel surface from corrosion. Therefore, recycling cigarette butts into a corrosion inhibitor provides environmental benefits while inhibiting corrosion of J55 steel used in oil and gas production.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Performance of a two Chambers Reactor for the Treatment of an Oily Effluent b...IJAEMSJORNAL
This work had as objective the development and analysis of a continuum flow reactor and measure its efficiency in the treatment of residual water of the biodiesel purification process using electro flocculation. The reactor was designed with two interconnected chambers with an 0.2 cm opening between then and reaction volume was 0.883 L and an electrolytic area of 351 cm². The electrodes were all aluminum, which were arranged in parallel and with 0.5 cm spacing, whose power was supplied by a DC source. As design variables, the influence of electrical potential (U) and residence time (τ) on: current density, final pH, removal of oils and greases, COD (Chemical Oxygen Demand), turbidity and total solids, in addition to quantification of the sludge mass obtained and the energy cost of the reactor. The best performance was for a potential of 6.0 volts and a τ of 29.43 min, with 90% removal of oils and greases, 53% COD and 4.38 g of sludge, culminating in an energy consumption ranging from 0.708 kWhm-3 to 4.73 kWhm-3. In addition, by visual analysis of the formation of bubbles and the removal of turbidity (94%), it was concluded that the division of the reactor in two chambers reduced the secondary contamination of the treated effluent.
Analysis of calorimetric measurement bismuth and tin system editorijrei
Lead-free soldering alloys with low melting point suitable for use in soldering joints are very essential. Use of lead as a solder is considered dangerous for the environment due to the huge number of printed circuit board and electronic devices, pipe joints etc. needed to be recycled from dumps.
In this work the metallic samples were prepared from Bi in the mass range from 0.75gm. Samples of Sn were dropped into the bath of pure Bi by using an automatic dropping device. System required 40min time interval after every sample of dropped. Calorimetric measurements was done at temperature 830K. The Integral and partial enthalpy of mixing was calculated at this temperatures. The Integral enthalpy of mixing in Bi- Sn system at 830K is endothermic in nature throughout the composition and its maximum value at Xsn = 0.6, is 1005.9061 respectively.
Effects of anion on the corrosion behaviors of carbon steel under artificial ...eSAT Journals
Abstract
Rain is one of the main importance issues for atmospheric corrosion problem. Effects of rainfall on corrosion behaviors of carbon steels were investigated using artificial rainfall equipment. Three types of Atmospheric Corrosion Monitoring (ACM) sensors, which consist of Fe-Ag, Zn-Ag, and Al-Ag galvanic couples, were used to illustrate the correlation between the sensors output, Corrosion Rate (CR), and chemical concentration in the rain. The effects of ionic species on the corrosion behaviors were observed by using NaCl, KCl, Na2SO4, NaNO3, and KNO3 as rainfall solutions. The result revealed that the rainfall rate was insensitive to ACM sensors outputs and CRs. In contrast, the chemical species and their concentrations in the rainfall solution significantly affected the ACM outputs and CRs. The corrosivity of the cations (Na+ and K+) is negligible compared to the anions (Cl-, SO42-, NO3-).For a given number of molar concentration, the CRs resulted from the corrosivity of SO4-2anions were higher than that of Cl- and NO3- anions, respectively. According to the empirical data, the CRs is increased and then reach a steady state as the molar concentration is continuously increased. This research also indicates that the ACM sensors outputs of Fe-Ag and Zn-Ag couples are capable of estimating corrosivity of the atmosphere, while the ACM sensor of Al-Agcouple can be used to determine not only the time of wetness but also the typeofchemical species in the environment. The research methods discussed in this paper proves that the CRs are dependent on the atmospheric composition and can be forecasted through ACM sensors.
Neuro identification of some commonly used volatile organic compounds using e...Alexander Decker
This document describes a study that used an electronic nose system with three gas sensors and an artificial neural network to identify three volatile organic compounds (formaldehyde, acetone, and chloroform). Sensor responses were analyzed and 60% of data was used to train the neural network, which successfully identified the compounds. The system has potential for applications in environmental monitoring and industrial process control.
The document discusses fibre optic sensors for measuring pH. It describes how fibre optic sensors work by modulating light properties like intensity, phase or wavelength. They have advantages for biomedical applications like in vivo monitoring. An ideal fibre optic sensor for biomedicine would be reliable, easy for operators to use, and low cost. The document discusses measuring blood pH, gastric/esophageal pH, and tissue pH using fibre optic sensors. It describes different sensor designs and challenges like sensitivity to light propagation. Fibre optic sensors eliminate drawbacks of traditional glass pH electrodes.
Este documento narra la llegada de Mónica y su sobrina Mariana a la quinta "Palma sola", donde vivirán durante unos meses. Describe la casa y los recuerdos que despierta en Mónica de su infancia. También presenta a Mariana, quien expresa en su diario sentirse sola y aburrida al tener que vivir allí lejos de sus amigos, a la espera del regreso de sus padres.
Inilah cara memasukkan gambar pada microsoft word :
Klik menu insert pada toolbar standar
Klik picture
Akan muncul kotak dialog insert picture
Cari folder dimana picture tersimpan
Klik file gambar yang dikehendaki
Klik insert
File gambar akan muncul dalam dokumen dan dan gambar akan terletak dimana letak kursor tadi berada.
The document describes Amrapali Leisure Park, a new residential project launched by Amrapali Group in Noida Extension. It offers luxury 2 and 3 BHK apartments ranging from 845 to 1730 square feet, priced from 29.15 lacs onwards. The Amrapali Group was established by Anil Sharma, an IIT Kharagpur graduate, and has completed over 100 acre projects with a focus on quality and affordable service.
Because, unlike most of our subjective feelings and their limited role in life, bhakti is an experience which is the objective source of revitalization for the whole universe! Bhakti is nothing else but the phenomenon of the flow of universal blessing through an individual for the rejuvenation of the entire universe forever!
Narayaniyam is a medieval Sanskrit text, comprising a summary study in poetic form of the Bhagavata Purana. It was composed by Melpathur Narayana Bhattathiri, (1560-1666 A.D.) one of the celebrated Sanskrit poets in Kerala. Even though the Narayaneeyam was completed as early as 1586 A.D., it appeared in print only after more than 250 years. The Bhagavata Purana is a major Hindu scripture consisting of about 18,000 verses, mainly devoted to the worship of Krishna.
Agile Maine Meeting - Challenges and options in guiding agile adoptions agilemaine
This document summarizes the key challenges and options for organizations undergoing an agile adoption, as presented by Dave Moran. Some of the major challenges discussed include changing mindsets, copying practices superficially without adopting values, managing pushback to change, and empowering teams. The document provides guidance on addressing these challenges, such as focusing on reducing work-in-process, gaining commitment to change, distributing authority alongside information, and transforming the way the organization operates rather than just its structure. Coaching is presented as an effective way to support teams in learning and applying new approaches while working.
Eva Persson is a photographer whose website is evapersson.com. She has taken pictures for the publications Art+Auction and Helsingin kaupungin asunnot Oy.
Victoria sobre el cáncer - Matthias RathWalther2013
La pandemia de COVID-19 ha tenido un impacto significativo en la economía mundial. Muchos países experimentaron fuertes caídas en el PIB y aumentos en el desempleo debido a los cierres. Ahora, a medida que se levantan las restricciones, la recuperación económica será gradual a medida que los consumidores y las empresas se readaptan a la nueva normalidad.
Narayaniyam is a medieval Sanskrit text, comprising a summary study in poetic form of the Bhagavata Purana. It was composed by Melpathur Narayana Bhattathiri, (1560-1666 A.D.) one of the celebrated Sanskrit poets in Kerala. Even though the Narayaneeyam was completed as early as 1586 A.D., it appeared in print only after more than 250 years. The Bhagavata Purana is a major Hindu scripture consisting of about 18,000 verses, mainly devoted to the worship of Krishna.
This document provides examples to illustrate the use of the present simple and present continuous tenses in English. It shows sentence constructions using different verbs in both tenses and analyzes when each tense would be used based on whether the verb describes an action, state, repeated event, or ongoing activity. Key distinctions are made between verbs that indicate an action which can be used in either tense versus stative verbs which are generally only used in the present simple tense.
Study of cigarette butts extract as corrosiveinhibiting agent in j55 steel ma...eSAT Publishing House
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology
Study of cigarette butts extract as corrosiveinhibiting agent in j55 steel ma...eSAT Journals
This document summarizes a study on using extracts from cigarette butts as a corrosion inhibitor for J55 steel. Weight loss tests and electrochemical techniques showed the cigarette butt extract inhibited corrosion of J55 steel in 15% hydrochloric acid solution. The highest inhibition efficiencies were 99% at 30°C and 61% at 105°C using a 6% concentration of the extract. Scanning electron microscopy confirmed the extract protected the steel surface from corrosion. Therefore, recycling cigarette butts into a corrosion inhibitor provides environmental benefits while inhibiting corrosion of J55 steel used in oil and gas production.
IJRET : International Journal of Research in Engineering and Technology is an international peer reviewed, online journal published by eSAT Publishing House for the enhancement of research in various disciplines of Engineering and Technology. The aim and scope of the journal is to provide an academic medium and an important reference for the advancement and dissemination of research results that support high-level learning, teaching and research in the fields of Engineering and Technology. We bring together Scientists, Academician, Field Engineers, Scholars and Students of related fields of Engineering and Technology.
Performance of a two Chambers Reactor for the Treatment of an Oily Effluent b...IJAEMSJORNAL
This work had as objective the development and analysis of a continuum flow reactor and measure its efficiency in the treatment of residual water of the biodiesel purification process using electro flocculation. The reactor was designed with two interconnected chambers with an 0.2 cm opening between then and reaction volume was 0.883 L and an electrolytic area of 351 cm². The electrodes were all aluminum, which were arranged in parallel and with 0.5 cm spacing, whose power was supplied by a DC source. As design variables, the influence of electrical potential (U) and residence time (τ) on: current density, final pH, removal of oils and greases, COD (Chemical Oxygen Demand), turbidity and total solids, in addition to quantification of the sludge mass obtained and the energy cost of the reactor. The best performance was for a potential of 6.0 volts and a τ of 29.43 min, with 90% removal of oils and greases, 53% COD and 4.38 g of sludge, culminating in an energy consumption ranging from 0.708 kWhm-3 to 4.73 kWhm-3. In addition, by visual analysis of the formation of bubbles and the removal of turbidity (94%), it was concluded that the division of the reactor in two chambers reduced the secondary contamination of the treated effluent.
Analysis of calorimetric measurement bismuth and tin system editorijrei
Lead-free soldering alloys with low melting point suitable for use in soldering joints are very essential. Use of lead as a solder is considered dangerous for the environment due to the huge number of printed circuit board and electronic devices, pipe joints etc. needed to be recycled from dumps.
In this work the metallic samples were prepared from Bi in the mass range from 0.75gm. Samples of Sn were dropped into the bath of pure Bi by using an automatic dropping device. System required 40min time interval after every sample of dropped. Calorimetric measurements was done at temperature 830K. The Integral and partial enthalpy of mixing was calculated at this temperatures. The Integral enthalpy of mixing in Bi- Sn system at 830K is endothermic in nature throughout the composition and its maximum value at Xsn = 0.6, is 1005.9061 respectively.
Effects of anion on the corrosion behaviors of carbon steel under artificial ...eSAT Journals
Abstract
Rain is one of the main importance issues for atmospheric corrosion problem. Effects of rainfall on corrosion behaviors of carbon steels were investigated using artificial rainfall equipment. Three types of Atmospheric Corrosion Monitoring (ACM) sensors, which consist of Fe-Ag, Zn-Ag, and Al-Ag galvanic couples, were used to illustrate the correlation between the sensors output, Corrosion Rate (CR), and chemical concentration in the rain. The effects of ionic species on the corrosion behaviors were observed by using NaCl, KCl, Na2SO4, NaNO3, and KNO3 as rainfall solutions. The result revealed that the rainfall rate was insensitive to ACM sensors outputs and CRs. In contrast, the chemical species and their concentrations in the rainfall solution significantly affected the ACM outputs and CRs. The corrosivity of the cations (Na+ and K+) is negligible compared to the anions (Cl-, SO42-, NO3-).For a given number of molar concentration, the CRs resulted from the corrosivity of SO4-2anions were higher than that of Cl- and NO3- anions, respectively. According to the empirical data, the CRs is increased and then reach a steady state as the molar concentration is continuously increased. This research also indicates that the ACM sensors outputs of Fe-Ag and Zn-Ag couples are capable of estimating corrosivity of the atmosphere, while the ACM sensor of Al-Agcouple can be used to determine not only the time of wetness but also the typeofchemical species in the environment. The research methods discussed in this paper proves that the CRs are dependent on the atmospheric composition and can be forecasted through ACM sensors.
Neuro identification of some commonly used volatile organic compounds using e...Alexander Decker
This document describes a study that used an electronic nose system with three gas sensors and an artificial neural network to identify three volatile organic compounds (formaldehyde, acetone, and chloroform). Sensor responses were analyzed and 60% of data was used to train the neural network, which successfully identified the compounds. The system has potential for applications in environmental monitoring and industrial process control.
The document discusses fibre optic sensors for measuring pH. It describes how fibre optic sensors work by modulating light properties like intensity, phase or wavelength. They have advantages for biomedical applications like in vivo monitoring. An ideal fibre optic sensor for biomedicine would be reliable, easy for operators to use, and low cost. The document discusses measuring blood pH, gastric/esophageal pH, and tissue pH using fibre optic sensors. It describes different sensor designs and challenges like sensitivity to light propagation. Fibre optic sensors eliminate drawbacks of traditional glass pH electrodes.
Este documento narra la llegada de Mónica y su sobrina Mariana a la quinta "Palma sola", donde vivirán durante unos meses. Describe la casa y los recuerdos que despierta en Mónica de su infancia. También presenta a Mariana, quien expresa en su diario sentirse sola y aburrida al tener que vivir allí lejos de sus amigos, a la espera del regreso de sus padres.
Inilah cara memasukkan gambar pada microsoft word :
Klik menu insert pada toolbar standar
Klik picture
Akan muncul kotak dialog insert picture
Cari folder dimana picture tersimpan
Klik file gambar yang dikehendaki
Klik insert
File gambar akan muncul dalam dokumen dan dan gambar akan terletak dimana letak kursor tadi berada.
The document describes Amrapali Leisure Park, a new residential project launched by Amrapali Group in Noida Extension. It offers luxury 2 and 3 BHK apartments ranging from 845 to 1730 square feet, priced from 29.15 lacs onwards. The Amrapali Group was established by Anil Sharma, an IIT Kharagpur graduate, and has completed over 100 acre projects with a focus on quality and affordable service.
Because, unlike most of our subjective feelings and their limited role in life, bhakti is an experience which is the objective source of revitalization for the whole universe! Bhakti is nothing else but the phenomenon of the flow of universal blessing through an individual for the rejuvenation of the entire universe forever!
Narayaniyam is a medieval Sanskrit text, comprising a summary study in poetic form of the Bhagavata Purana. It was composed by Melpathur Narayana Bhattathiri, (1560-1666 A.D.) one of the celebrated Sanskrit poets in Kerala. Even though the Narayaneeyam was completed as early as 1586 A.D., it appeared in print only after more than 250 years. The Bhagavata Purana is a major Hindu scripture consisting of about 18,000 verses, mainly devoted to the worship of Krishna.
Agile Maine Meeting - Challenges and options in guiding agile adoptions agilemaine
This document summarizes the key challenges and options for organizations undergoing an agile adoption, as presented by Dave Moran. Some of the major challenges discussed include changing mindsets, copying practices superficially without adopting values, managing pushback to change, and empowering teams. The document provides guidance on addressing these challenges, such as focusing on reducing work-in-process, gaining commitment to change, distributing authority alongside information, and transforming the way the organization operates rather than just its structure. Coaching is presented as an effective way to support teams in learning and applying new approaches while working.
Eva Persson is a photographer whose website is evapersson.com. She has taken pictures for the publications Art+Auction and Helsingin kaupungin asunnot Oy.
Victoria sobre el cáncer - Matthias RathWalther2013
La pandemia de COVID-19 ha tenido un impacto significativo en la economía mundial. Muchos países experimentaron fuertes caídas en el PIB y aumentos en el desempleo debido a los cierres. Ahora, a medida que se levantan las restricciones, la recuperación económica será gradual a medida que los consumidores y las empresas se readaptan a la nueva normalidad.
Narayaniyam is a medieval Sanskrit text, comprising a summary study in poetic form of the Bhagavata Purana. It was composed by Melpathur Narayana Bhattathiri, (1560-1666 A.D.) one of the celebrated Sanskrit poets in Kerala. Even though the Narayaneeyam was completed as early as 1586 A.D., it appeared in print only after more than 250 years. The Bhagavata Purana is a major Hindu scripture consisting of about 18,000 verses, mainly devoted to the worship of Krishna.
This document provides examples to illustrate the use of the present simple and present continuous tenses in English. It shows sentence constructions using different verbs in both tenses and analyzes when each tense would be used based on whether the verb describes an action, state, repeated event, or ongoing activity. Key distinctions are made between verbs that indicate an action which can be used in either tense versus stative verbs which are generally only used in the present simple tense.
Electrochemical carbon monoxide sensors require regular maintenance to function properly and maximize their lifespan. They work by measuring the current produced from oxidation and reduction chemical reactions between electrodes and electrolytes when exposed to carbon monoxide gas. Typically, electrochemical gas sensors can operate for one to three years, but following manufacturer recommended calibration procedures every six months can extend their lifespan to five to seven years. It is important to calibrate the sensors regularly given the toxicity of carbon monoxide and potential safety consequences if the sensors provide inaccurate readings over time.
Graphene/PSMA composite for gas sensing applicationjournalBEEI
This paper presents the fabrication of conducting polymer sensor which comprise of graphene-poly styrene-co-maleic acid (PSMA) composite that responds to volatile organic compound (VOC) via a change in the electrical resistance of the sensors. Five sensors composed of different material ratio were fabricated to find out the most prominent weight percentage ratio (wt %) for optimum sensor response. Those materials were deposited onto silver electrode using drop-casting method. NI Card PCIE-6323 measures the voltage obtained from the sensor circuit and the resistance of the gas sensor monitored using LabVIEW instrument. It was observed from the experiments that combination of 60% graphene and 40% PSMA gives the highest sensor response.
IRJET- Design of Eco Friendly System in Automobile for Environmental SafetyIRJET Journal
This document discusses the design of an eco-friendly system to monitor vehicle emissions. The system would use sensors to measure levels of harmful gases in a vehicle's exhaust, like carbon monoxide, nitrogen oxides, hydrocarbons and oxygen. It would display the emission levels to the driver using an OLED display to increase awareness of engine health and emissions. For high emission levels, the system could cut off the vehicle's ignition using a controller. The document reviews different sensor technologies that could be used to monitor the key gases and aims to help reduce environmental pollution from vehicle emissions.
Cost Effective Experimental Setup for Gas Sensing Applicationsiosrjce
IOSR Journal of Applied Chemistry (IOSR-JAC) is a double blind peer reviewed International Journal that provides rapid publication (within a month) of articles in all areas of applied chemistry and its applications. The journal welcomes publications of high quality papers on theoretical developments and practical applications in Chemical Science. Original research papers, state-of-the-art reviews, and high quality technical notes are invited for publications.
This document describes the development of a low-cost adjustable gaseous exhaust analyzer for runtime characterization of vehicle emissions. The analyzer uses a telescopic tube arrangement to passively control exhaust temperature for different sensor needs. It can monitor CO, NOx, CO2, and humidity concentrations in real-time. The analyzer was validated against commercial instruments, showing results within 20% error. Future work will incorporate flow sensors and monitor additional gases to allow for a more complete emissions analysis.
Design of Electronic Nose System Using Gas Chromatography Principle and Surfa...TELKOMNIKA JOURNAL
Most gases are odorless, colorless and also hazard to be sensed by the human olfactory system.
Hence, an electronic nose system is required for the gas classification process. This study presents the
design of electronic nose system using a combination of Gas Chromatography Column and a Surface
Acoustic Wave (SAW). The Gas Chromatography Column is a technique based on the compound partition
at a certain temperature. Whereas, the SAW sensor works based on the resonant frequency change. In
this study, gas samples including methanol, acetonitrile, and benzene are used for system performance
measurement. Each gas sample generates a specific acoustic signal data in the form of a frequency
change recorded by the SAW sensor. Then, the acoustic signal data is analyzed to obtain the acoustic
features, i.e. the peak amplitude, the negative slope, the positive slope, and the length. The Support
Vector Machine (SVM) method using the acoustic feature as its input parameters are applied to classify
the gas sample. Radial Basis Function is used to build the optimal hyperplane model which devided into
two processes i.e., the training process and the external validation process. According to the result
performance, the training process has the accuracy of 98.7% and the external validation process has the
accuracy of 93.3%. Our electronic nose system has the average sensitivity of 51.43 Hz/mL to sense the
gas samples.
Drager Fixed Gas Detector - At The Heart Of Gas Detection Systems BrochureThorne & Derrick UK
This document discusses gas detection systems and focuses on electrochemical and catalytic gas sensors. It provides details on how electrochemical sensors use a chemical reaction between electrodes to detect gases. Catalytic sensors detect flammable gases by measuring the temperature increase caused by their catalytic oxidation. The document emphasizes that Dräger sensors are intelligently designed to work reliably with gas detectors to quickly and accurately identify hazards through stored sensor data and testing.
Analysis of various sensors to measure the physical parameters of the oil sto...IRJET Journal
The document discusses various sensors that can be used to measure physical parameters of oil stored in tanks for oil and gas industries in Oman. It describes sensors such as pressure sensors, thermometers, flowmeters, gas analyzers, densitometers, and ultrasonic sensors that can measure properties like pressure, temperature, flow, gas levels, density, and tank level. The document suggests that using a smart monitoring system with suitable sensors can provide a safe environment and enhanced production for oil and gas industries.
Inkjet printed graphene-based flexible humidity sensor for environmental appl...Conference Papers
This document summarizes research on an inkjet-printed graphene-based flexible humidity sensor. Key points:
- Researchers from MIMOS Berhad developed a humidity sensor consisting of an interdigitated electrode made from reduced graphene oxide and silver nanoparticle ink, with graphene oxide as the sensing material, printed on a flexible polyethylene terephthalate substrate.
- The graphene oxide sensing material's dielectric constant changes with humidity, allowing the sensor to detect humidity levels based on capacitance measurements.
- Testing showed the sensor achieved a highest sensitivity of 0.15pF/%RH at 50°C, with a linear response at low humidity and exponential increase above 60%RH. It also demonstrated good temperature dependence below
Recent development in electronic nose data processing for beef quality assess...TELKOMNIKA JOURNAL
Beef is kind of perishable food that easily to decay. Hence, a rapid system for beef quality assessment is needed to guarantee the quality of beef. In the last few years, electronic nose (e-nose) is developed for beef spoilage detection. In this paper, we discuss the challenges of e-nose application to beef quality assessment, especially in e-nose data processing. We also provide a summary of our previous studies that explains several methods to deal with gas sensor noise, sensor array optimization problem, beef quality classification, and prediction of the microbial population in beef sample. This paper might be useful for researchers and practitioners to understand the challenges and methods of e-nose data processing for beef quality assessment.
IRJET- Aircop – An Air Pollution Monitoring DeviceIRJET Journal
1. The document describes a device called AIRCOP that was developed for remote monitoring of air pollution factors using Internet of Things technology.
2. AIRCOP monitors carbon monoxide, air quality, particulate matter, temperature, humidity, atmospheric pressure, and wind speed using low-cost sensors.
3. The sensor data is sent to a cloud-based IoT platform called Thingspeak where it is stored and visualized, allowing continuous monitoring of environmental conditions.
This document describes a novel system for creating stable nanoparticle aerosols from nanopowders. The system uses a minimal amount of test material (200 mg) and follows the concept of a fluidized bed process using a modified V-shaped aerosol generator. It is able to produce stable aerosol generation rates and particle size distributions over long periods of 0.5-2 hours. The system allows for studying aerosol behavior important for toxicological studies and facilitates understanding occupational exposures to nanopowders.
This document summarizes research on synthesizing high resistive Bismuth ferrite (BiFeO3) thin films for ethanol sensing applications using pulsed laser deposition. Key points:
1) BiFeO3 is a promising material for room temperature gas sensing due to a potential redox reaction on film surfaces when exposed to ethanol vapors, causing a change in resistivity.
2) Highly resistive BiFeO3 thin films were grown on substrates like silicon, silicon dioxide, and quartz at different deposition conditions using pulsed laser deposition.
3) X-ray diffraction analysis confirmed the films had a pure perovskite structure without impurities. Resistivity measurements found the films
Accuracy Improvement of PM Measuring Instrumentsijtsrd
The PM10 concentration in the underground areas should be monitored to protect the health of the commuters in the underground subway system. The purpose of this work is to study the reliability of the instruments using light scattering method to measure the PM10 concentrations continuously. A linear regression analysis method is used to improve the performance of the instruments using light scattering method. Some experimental results show that a linear regression technique would be very helpful for the performance improvement of light scattering instruments such as Air test PM2500 and HCT 4103. Tae-In Hyon | Gyu-Sik Kim "Accuracy Improvement of PM Measuring Instruments" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-3 | Issue-5 , August 2019, URL: https://www.ijtsrd.com/papers/ijtsrd26722.pdfPaper URL: https://www.ijtsrd.com/engineering/electrical-engineering/26722/accuracy-improvement-of-pm-measuring-instruments/tae-in-hyon
SIMULATION OF MEMS MICROHOTPLATE FOR METAL OXIDE GAS SENSORS: REVIEWIJEEE
Simulation of gas sensor with integrated micro hotplate (MHP) of ultra low power consumption is reviewed. Various parameters of gas sensor and MHP as power, temperature ,heat insulation ,stress analysis and deflection is studied using various Multiphysics simulation tools like ANSYS and Conventorware
The document summarizes research on using nanoparticles to improve gas sensor performance. It discusses how reducing metal oxide particles sizes to the nanoscale can dramatically increase their surface area and gas detection sensitivity, selectivity, and response time. The researcher has developed gas sensor prototypes using various metal oxide nanomaterials deposited as thick films or multilayer structures. Nanofabrication methods are also being explored to create high surface area sensor platforms using anodic aluminum oxide templates. Overall, the research aims to leverage nanotechnology to develop lower cost, higher performance gas sensors for industrial and environmental monitoring applications.
We specialise in Bioaerosols, Sick Building Syndrome, Fenceline Monitoring, Urban air quality, Industrial air quality, construction air quality, CEMS, CAMS and much more.
Reliable e-nose for air toxicity monitoring by filter diagonalization methodIJECEIAES
This document describes an electronic nose (e-nose) device designed to detect toxic air compounds that could threaten human health. The e-nose uses an array of 6 metal oxide semiconductor sensors to detect gases like carbon monoxide, combustible gas, hydrogen, methane, and smoke. It includes an electronic module for data acquisition and software for signal processing and visualization. This study proposes using the filter diagonalization method to analyze the spectral content of the sensor signals. Preliminary results found the prototype to be functional and the filter diagonalization method suitable for later classification. Potential applications of the e-nose include indoor and hazardous environment monitoring.
This document describes the design and analysis of a surface acoustic wave (SAW) based microelectromechanical systems (MEMS) gas sensor for detecting volatile organic gases. The sensor uses interdigitated transducers on a lithium niobate piezoelectric substrate coated with a polyisobutylene sensing film. Finite element modeling was used to simulate the sensor's response to various gases. The simulations showed shifts in resonant frequency when exposed to different gases, allowing for gas detection via mass loading effects. Sensitivity analysis found the sensor responded most strongly to tetrachloroethene exposure due to its high absorbed partial density in the sensing film. The SAW sensor design could enable applications in chemical industry, environmental monitoring, and other
Submission Deadline: 30th September 2022
Acceptance Notification: Within Three Days’ time period
Online Publication: Within 24 Hrs. time Period
Expected Date of Dispatch of Printed Journal: 5th October 2022
MODELING AND ANALYSIS OF SURFACE ROUGHNESS AND WHITE LATER THICKNESS IN WIRE-...IAEME Publication
White layer thickness (WLT) formed and surface roughness in wire electric discharge turning (WEDT) of tungsten carbide composite has been made to model through response surface methodology (RSM). A Taguchi’s standard Design of experiments involving five input variables with three levels has been employed to establish a mathematical model between input parameters and responses. Percentage of cobalt content, spindle speed, Pulse on-time, wire feed and pulse off-time were changed during the experimental tests based on the Taguchi’s orthogonal array L27 (3^13). Analysis of variance (ANOVA) revealed that the mathematical models obtained can adequately describe performance within the parameters of the factors considered. There was a good agreement between the experimental and predicted values in this study.
A STUDY ON THE REASONS FOR TRANSGENDER TO BECOME ENTREPRENEURSIAEME Publication
The study explores the reasons for a transgender to become entrepreneurs. In this study transgender entrepreneur was taken as independent variable and reasons to become as dependent variable. Data were collected through a structured questionnaire containing a five point Likert Scale. The study examined the data of 30 transgender entrepreneurs in Salem Municipal Corporation of Tamil Nadu State, India. Simple Random sampling technique was used. Garrett Ranking Technique (Percentile Position, Mean Scores) was used as the analysis for the present study to identify the top 13 stimulus factors for establishment of trans entrepreneurial venture. Economic advancement of a nation is governed upon the upshot of a resolute entrepreneurial doings. The conception of entrepreneurship has stretched and materialized to the socially deflated uncharted sections of transgender community. Presently transgenders have smashed their stereotypes and are making recent headlines of achievements in various fields of our Indian society. The trans-community is gradually being observed in a new light and has been trying to achieve prospective growth in entrepreneurship. The findings of the research revealed that the optimistic changes are taking place to change affirmative societal outlook of the transgender for entrepreneurial ventureship. It also laid emphasis on other transgenders to renovate their traditional living. The paper also highlights that legislators, supervisory body should endorse an impartial canons and reforms in Tamil Nadu Transgender Welfare Board Association.
BROAD UNEXPOSED SKILLS OF TRANSGENDER ENTREPRENEURSIAEME Publication
Since ages gender difference is always a debatable theme whether caused by nature, evolution or environment. The birth of a transgender is dreadful not only for the child but also for their parents. The pain of living in the wrong physique and treated as second class victimized citizen is outrageous and fully harboured with vicious baseless negative scruples. For so long, social exclusion had perpetuated inequality and deprivation experiencing ingrained malign stigma and besieged victims of crime or violence across their life spans. They are pushed into the murky way of life with a source of eternal disgust, bereft sexual potency and perennial fear. Although they are highly visible but very little is known about them. The common public needs to comprehend the ravaged arrogance on these insensitive souls and assist in integrating them into the mainstream by offering equal opportunity, treat with humanity and respect their dignity. Entrepreneurship in the current age is endorsing the gender fairness movement. Unstable careers and economic inadequacy had inclined one of the gender variant people called Transgender to become entrepreneurs. These tiny budding entrepreneurs resulted in economic transition by means of employment, free from the clutches of stereotype jobs, raised standard of living and handful of financial empowerment. Besides all these inhibitions, they were able to witness a platform for skill set development that ignited them to enter into entrepreneurial domain. This paper epitomizes skill sets involved in trans-entrepreneurs of Thoothukudi Municipal Corporation of Tamil Nadu State and is a groundbreaking determination to sightsee various skills incorporated and the impact on entrepreneurship.
DETERMINANTS AFFECTING THE USER'S INTENTION TO USE MOBILE BANKING APPLICATIONSIAEME Publication
The banking and financial services industries are experiencing increased technology penetration. Among them, the banking industry has made technological advancements to better serve the general populace. The economy focused on transforming the banking sector's system into a cashless, paperless, and faceless one. The researcher wants to evaluate the user's intention for utilising a mobile banking application. The study also examines the variables affecting the user's behaviour intention when selecting specific applications for financial transactions. The researcher employed a well-structured questionnaire and a descriptive study methodology to gather the respondents' primary data utilising the snowball sampling technique. The study includes variables like performance expectations, effort expectations, social impact, enabling circumstances, and perceived risk. Each of the aforementioned variables has a major impact on how users utilise mobile banking applications. The outcome will assist the service provider in comprehending the user's history with mobile banking applications.
ANALYSE THE USER PREDILECTION ON GPAY AND PHONEPE FOR DIGITAL TRANSACTIONSIAEME Publication
Technology upgradation in banking sector took the economy to view that payment mode towards online transactions using mobile applications. This system enabled connectivity between banks, Merchant and user in a convenient mode. there are various applications used for online transactions such as Google pay, Paytm, freecharge, mobikiwi, oxygen, phonepe and so on and it also includes mobile banking applications. The study aimed at evaluating the predilection of the user in adopting digital transaction. The study is descriptive in nature. The researcher used random sample techniques to collect the data. The findings reveal that mobile applications differ with the quality of service rendered by Gpay and Phonepe. The researcher suggest the Phonepe application should focus on implementing the application should be user friendly interface and Gpay on motivating the users to feel the importance of request for money and modes of payments in the application.
VOICE BASED ATM FOR VISUALLY IMPAIRED USING ARDUINOIAEME Publication
The prototype of a voice-based ATM for visually impaired using Arduino is to help people who are blind. This uses RFID cards which contain users fingerprint encrypted on it and interacts with the users through voice commands. ATM operates when sensor detects the presence of one person in the cabin. After scanning the RFID card, it will ask to select the mode like –normal or blind. User can select the respective mode through voice input, if blind mode is selected the balance check or cash withdraw can be done through voice input. Normal mode procedure is same as the existing ATM.
IMPACT OF EMOTIONAL INTELLIGENCE ON HUMAN RESOURCE MANAGEMENT PRACTICES AMONG...IAEME Publication
There is increasing acceptability of emotional intelligence as a major factor in personality assessment and effective human resource management. Emotional intelligence as the ability to build capacity, empathize, co-operate, motivate and develop others cannot be divorced from both effective performance and human resource management systems. The human person is crucial in defining organizational leadership and fortunes in terms of challenges and opportunities and walking across both multinational and bilateral relationships. The growing complexity of the business world requires a great deal of self-confidence, integrity, communication, conflict and diversity management to keep the global enterprise within the paths of productivity and sustainability. Using the exploratory research design and 255 participants the result of this original study indicates strong positive correlation between emotional intelligence and effective human resource management. The paper offers suggestions on further studies between emotional intelligence and human capital development and recommends for conflict management as an integral part of effective human resource management.
VISUALISING AGING PARENTS & THEIR CLOSE CARERS LIFE JOURNEY IN AGING ECONOMYIAEME Publication
Our life journey, in general, is closely defined by the way we understand the meaning of why we coexist and deal with its challenges. As we develop the "inspiration economy", we could say that nearly all of the challenges we have faced are opportunities that help us to discover the rest of our journey. In this note paper, we explore how being faced with the opportunity of being a close carer for an aging parent with dementia brought intangible discoveries that changed our insight of the meaning of the rest of our life journey.
A STUDY ON THE IMPACT OF ORGANIZATIONAL CULTURE ON THE EFFECTIVENESS OF PERFO...IAEME Publication
The main objective of this study is to analyze the impact of aspects of Organizational Culture on the Effectiveness of the Performance Management System (PMS) in the Health Care Organization at Thanjavur. Organizational Culture and PMS play a crucial role in present-day organizations in achieving their objectives. PMS needs employees’ cooperation to achieve its intended objectives. Employees' cooperation depends upon the organization’s culture. The present study uses exploratory research to examine the relationship between the Organization's culture and the Effectiveness of the Performance Management System. The study uses a Structured Questionnaire to collect the primary data. For this study, Thirty-six non-clinical employees were selected from twelve randomly selected Health Care organizations at Thanjavur. Thirty-two fully completed questionnaires were received.
Living in 21st century in itself reminds all of us the necessity of police and its administration. As more and more we are entering into the modern society and culture, the more we require the services of the so called ‘Khaki Worthy’ men i.e., the police personnel. Whether we talk of Indian police or the other nation’s police, they all have the same recognition as they have in India. But as already mentioned, their services and requirements are different after the like 26th November, 2008 incidents, where they without saving their own lives has sacrificed themselves without any hitch and without caring about their respective family members and wards. In other words, they are like our heroes and mentors who can guide us from the darkness of fear, militancy, corruption and other dark sides of life and so on. Now the question arises, if Gandhi would have been alive today, what would have been his reaction/opinion to the police and its functioning? Would he have some thing different in his mind now what he had been in his mind before the partition or would he be going to start some Satyagraha in the form of some improvement in the functioning of the police administration? Really these questions or rather night mares can come to any one’s mind, when there is too much confusion is prevailing in our minds, when there is too much corruption in the society and when the polices working is also in the questioning because of one or the other case throughout the India. It is matter of great concern that we have to thing over our administration and our practical approach because the police personals are also like us, they are part and parcel of our society and among one of us, so why we all are pin pointing towards them.
A STUDY ON TALENT MANAGEMENT AND ITS IMPACT ON EMPLOYEE RETENTION IN SELECTED...IAEME Publication
The goal of this study was to see how talent management affected employee retention in the selected IT organizations in Chennai. The fundamental issue was the difficulty to attract, hire, and retain talented personnel who perform well and the gap between supply and demand of talent acquisition and retaining them within the firms. The study's main goals were to determine the impact of talent management on employee retention in IT companies in Chennai, investigate talent management strategies that IT companies could use to improve talent acquisition, performance management, career planning and formulate retention strategies that the IT firms could use. The respondents were given a structured close-ended questionnaire with the 5 Point Likert Scale as part of the study's quantitative research design. The target population consisted of 289 IT professionals. The questionnaires were distributed and collected by the researcher directly. The Statistical Package for Social Sciences (SPSS) was used to collect and analyse the questionnaire responses. Hypotheses that were formulated for the various areas of the study were tested using a variety of statistical tests. The key findings of the study suggested that talent management had an impact on employee retention. The studies also found that there is a clear link between the implementation of talent management and retention measures. Management should provide enough training and development for employees, clarify job responsibilities, provide adequate remuneration packages, and recognise employees for exceptional performance.
ATTRITION IN THE IT INDUSTRY DURING COVID-19 PANDEMIC: LINKING EMOTIONAL INTE...IAEME Publication
Globally, Millions of dollars were spent by the organizations for employing skilled Information Technology (IT) professionals. It is costly to replace unskilled employees with IT professionals possessing technical skills and competencies that aid in interconnecting the business processes. The organization’s employment tactics were forced to alter by globalization along with technological innovations as they consistently diminish to remain lean, outsource to concentrate on core competencies along with restructuring/reallocate personnel to gather efficiency. As other jobs, organizations or professions have become reasonably more appropriate in a shifting employment landscape, the above alterations trigger both involuntary as well as voluntary turnover. The employee view on jobs is also afflicted by the COVID-19 pandemic along with the employee-driven labour market. So, having effective strategies is necessary to tackle the withdrawal rate of employees. By associating Emotional Intelligence (EI) along with Talent Management (TM) in the IT industry, the rise in attrition rate was analyzed in this study. Only 303 respondents were collected out of 350 participants to whom questionnaires were distributed. From the employees of IT organizations located in Bangalore (India), the data were congregated. A simple random sampling methodology was employed to congregate data as of the respondents. Generating the hypothesis along with testing is eventuated. The effect of EI and TM along with regression analysis between TM and EI was analyzed. The outcomes indicated that employee and Organizational Performance (OP) were elevated by effective EI along with TM.
INFLUENCE OF TALENT MANAGEMENT PRACTICES ON ORGANIZATIONAL PERFORMANCE A STUD...IAEME Publication
By implementing talent management strategy, organizations would have the option to retain their skilled professionals while additionally working on their overall performance. It is the course of appropriately utilizing the ideal individuals, setting them up for future top positions, exploring and dealing with their performance, and holding them back from leaving the organization. It is employee performance that determines the success of every organization. The firm quickly obtains an upper hand over its rivals in the event that its employees having particular skills that cannot be duplicated by the competitors. Thus, firms are centred on creating successful talent management practices and processes to deal with the unique human resources. Firms are additionally endeavouring to keep their top/key staff since on the off chance that they leave; the whole store of information leaves the firm's hands. The study's objective was to determine the impact of talent management on organizational performance among the selected IT organizations in Chennai. The study recommends that talent management limitedly affects performance. On the off chance that this talent is appropriately management and implemented properly, organizations might benefit as much as possible from their maintained assets to support development and productivity, both monetarily and non-monetarily.
A STUDY OF VARIOUS TYPES OF LOANS OF SELECTED PUBLIC AND PRIVATE SECTOR BANKS...IAEME Publication
Banking regulations act of India, 1949 defines banking as “acceptance of deposits for the purpose of lending or investment from the public, repayment on demand or otherwise and withdrawable through cheques, drafts order or otherwise”, the major participants of the Indian financial system are commercial banks, the financial institution encompassing term lending institutions. Investments institutions, specialized financial institution and the state level development banks, non banking financial companies (NBFC) and other market intermediaries such has the stock brokers and money lenders are among the oldest of the certain variants of NBFC and the oldest market participants. The asset quality of banks is one of the most important indicators of their financial health. The Indian banking sector has been facing severe problems of increasing Non- Performing Assets (NPAs). The NPAs growth directly and indirectly affects the quality of assets and profitability of banks. It also shows the efficiency of banks credit risk management and the recovery effectiveness. NPA do not generate any income, whereas, the bank is required to make provisions for such as assets that why is a double edge weapon. This paper outlines the concept of quality of bank loans of different types like Housing, Agriculture and MSME loans in state Haryana of selected public and private sector banks. This study is highlighting problems associated with the role of commercial bank in financing Small and Medium Scale Enterprises (SME). The overall objective of the research was to assess the effect of the financing provisions existing for the setting up and operations of MSMEs in the country and to generate recommendations for more robust financing mechanisms for successful operation of the MSMEs, in turn understanding the impact of MSME loans on financial institutions due to NPA. There are many research conducted on the topic of Non- Performing Assets (NPA) Management, concerning particular bank, comparative study of public and private banks etc. In this paper the researcher is considering the aggregate data of selected public sector and private sector banks and attempts to compare the NPA of Housing, Agriculture and MSME loans in state Haryana of public and private sector banks. The tools used in the study are average and Anova test and variance. The findings reveal that NPA is common problem for both public and private sector banks and is associated with all types of loans either that is housing loans, agriculture loans and loans to SMES. NPAs of both public and private sector banks show the increasing trend. In 2010-11 GNPA of public and private sector were at same level it was 2% but after 2010-11 it increased in many fold and at present there is GNPA in some more than 15%. It shows the dark area of Indian banking sector.
EXPERIMENTAL STUDY OF MECHANICAL AND TRIBOLOGICAL RELATION OF NYLON/BaSO4 POL...IAEME Publication
An experiment conducted in this study found that BaSO4 changed Nylon 6's mechanical properties. By changing the weight ratios, BaSO4 was used to make Nylon 6. This Researcher looked into how hard Nylon-6/BaSO4 composites are and how well they wear. Experiments were done based on Taguchi design L9. Nylon-6/BaSO4 composites can be tested for their hardness number using a Rockwell hardness testing apparatus. On Nylon/BaSO4, the wear behavior was measured by a wear monitor, pinon-disc friction by varying reinforcement, sliding speed, and sliding distance, and the microstructure of the crack surfaces was observed by SEM. This study provides significant contributions to ultimate strength by increasing BaSO4 content up to 16% in the composites, and sliding speed contributes 72.45% to the wear rate
ROLE OF SOCIAL ENTREPRENEURSHIP IN RURAL DEVELOPMENT OF INDIA - PROBLEMS AND ...IAEME Publication
The majority of the population in India lives in villages. The village is the back bone of the country. Village or rural industries play an important role in the national economy, particularly in the rural development. Developing the rural economy is one of the key indicators towards a country’s success. Whether it be the need to look after the welfare of the farmers or invest in rural infrastructure, Governments have to ensure that rural development isn’t compromised. The economic development of our country largely depends on the progress of rural areas and the standard of living of rural masses. Village or rural industries play an important role in the national economy, particularly in the rural development. Rural entrepreneurship is based on stimulating local entrepreneurial talent and the subsequent growth of indigenous enterprises. It recognizes opportunity in the rural areas and accelerates a unique blend of resources either inside or outside of agriculture. Rural entrepreneurship brings an economic value to the rural sector by creating new methods of production, new markets, new products and generate employment opportunities thereby ensuring continuous rural development. Social Entrepreneurship has the direct and primary objective of serving the society along with the earning profits. So, social entrepreneurship is different from the economic entrepreneurship as its basic objective is not to earn profits but for providing innovative solutions to meet the society needs which are not taken care by majority of the entrepreneurs as they are in the business for profit making as a sole objective. So, the Social Entrepreneurs have the huge growth potential particularly in the developing countries like India where we have huge societal disparities in terms of the financial positions of the population. Still 22 percent of the Indian population is below the poverty line and also there is disparity among the rural & urban population in terms of families living under BPL. 25.7 percent of the rural population & 13.7 percent of the urban population is under BPL which clearly shows the disparity of the poor people in the rural and urban areas. The need to develop social entrepreneurship in agriculture is dictated by a large number of social problems. Such problems include low living standards, unemployment, and social tension. The reasons that led to the emergence of the practice of social entrepreneurship are the above factors. The research problem lays upon disclosing the importance of role of social entrepreneurship in rural development of India. The paper the tendencies of social entrepreneurship in India, to present successful examples of such business for providing recommendations how to improve situation in rural areas in terms of social entrepreneurship development. Indian government has made some steps towards development of social enterprises, social entrepreneurship, and social in- novation, but a lot remains to be improved.
OPTIMAL RECONFIGURATION OF POWER DISTRIBUTION RADIAL NETWORK USING HYBRID MET...IAEME Publication
Distribution system is a critical link between the electric power distributor and the consumers. Most of the distribution networks commonly used by the electric utility is the radial distribution network. However in this type of network, it has technical issues such as enormous power losses which affect the quality of the supply. Nowadays, the introduction of Distributed Generation (DG) units in the system help improve and support the voltage profile of the network as well as the performance of the system components through power loss mitigation. In this study network reconfiguration was done using two meta-heuristic algorithms Particle Swarm Optimization and Gravitational Search Algorithm (PSO-GSA) to enhance power quality and voltage profile in the system when simultaneously applied with the DG units. Backward/Forward Sweep Method was used in the load flow analysis and simulated using the MATLAB program. Five cases were considered in the Reconfiguration based on the contribution of DG units. The proposed method was tested using IEEE 33 bus system. Based on the results, there was a voltage profile improvement in the system from 0.9038 p.u. to 0.9594 p.u.. The integration of DG in the network also reduced power losses from 210.98 kW to 69.3963 kW. Simulated results are drawn to show the performance of each case.
APPLICATION OF FRUGAL APPROACH FOR PRODUCTIVITY IMPROVEMENT - A CASE STUDY OF...IAEME Publication
Manufacturing industries have witnessed an outburst in productivity. For productivity improvement manufacturing industries are taking various initiatives by using lean tools and techniques. However, in different manufacturing industries, frugal approach is applied in product design and services as a tool for improvement. Frugal approach contributed to prove less is more and seems indirectly contributing to improve productivity. Hence, there is need to understand status of frugal approach application in manufacturing industries. All manufacturing industries are trying hard and putting continuous efforts for competitive existence. For productivity improvements, manufacturing industries are coming up with different effective and efficient solutions in manufacturing processes and operations. To overcome current challenges, manufacturing industries have started using frugal approach in product design and services. For this study, methodology adopted with both primary and secondary sources of data. For primary source interview and observation technique is used and for secondary source review has done based on available literatures in website, printed magazines, manual etc. An attempt has made for understanding application of frugal approach with the study of manufacturing industry project. Manufacturing industry selected for this project study is Mahindra and Mahindra Ltd. This paper will help researcher to find the connections between the two concepts productivity improvement and frugal approach. This paper will help to understand significance of frugal approach for productivity improvement in manufacturing industry. This will also help to understand current scenario of frugal approach in manufacturing industry. In manufacturing industries various process are involved to deliver the final product. In the process of converting input in to output through manufacturing process productivity plays very critical role. Hence this study will help to evolve status of frugal approach in productivity improvement programme. The notion of frugal can be viewed as an approach towards productivity improvement in manufacturing industries.
A MULTIPLE – CHANNEL QUEUING MODELS ON FUZZY ENVIRONMENTIAEME Publication
In this paper, we investigated a queuing model of fuzzy environment-based a multiple channel queuing model (M/M/C) ( /FCFS) and study its performance under realistic conditions. It applies a nonagonal fuzzy number to analyse the relevant performance of a multiple channel queuing model (M/M/C) ( /FCFS). Based on the sub interval average ranking method for nonagonal fuzzy number, we convert fuzzy number to crisp one. Numerical results reveal that the efficiency of this method. Intuitively, the fuzzy environment adapts well to a multiple channel queuing models (M/M/C) ( /FCFS) are very well.
Climate Impact of Software Testing at Nordic Testing DaysKari Kakkonen
My slides at Nordic Testing Days 6.6.2024
Climate impact / sustainability of software testing discussed on the talk. ICT and testing must carry their part of global responsibility to help with the climat warming. We can minimize the carbon footprint but we can also have a carbon handprint, a positive impact on the climate. Quality characteristics can be added with sustainability, and then measured continuously. Test environments can be used less, and in smaller scale and on demand. Test techniques can be used in optimizing or minimizing number of tests. Test automation can be used to speed up testing.
GraphSummit Singapore | The Art of the Possible with Graph - Q2 2024Neo4j
Neha Bajwa, Vice President of Product Marketing, Neo4j
Join us as we explore breakthrough innovations enabled by interconnected data and AI. Discover firsthand how organizations use relationships in data to uncover contextual insights and solve our most pressing challenges – from optimizing supply chains, detecting fraud, and improving customer experiences to accelerating drug discoveries.
Essentials of Automations: The Art of Triggers and Actions in FMESafe Software
In this second installment of our Essentials of Automations webinar series, we’ll explore the landscape of triggers and actions, guiding you through the nuances of authoring and adapting workspaces for seamless automations. Gain an understanding of the full spectrum of triggers and actions available in FME, empowering you to enhance your workspaces for efficient automation.
We’ll kick things off by showcasing the most commonly used event-based triggers, introducing you to various automation workflows like manual triggers, schedules, directory watchers, and more. Plus, see how these elements play out in real scenarios.
Whether you’re tweaking your current setup or building from the ground up, this session will arm you with the tools and insights needed to transform your FME usage into a powerhouse of productivity. Join us to discover effective strategies that simplify complex processes, enhancing your productivity and transforming your data management practices with FME. Let’s turn complexity into clarity and make your workspaces work wonders!
Building Production Ready Search Pipelines with Spark and MilvusZilliz
Spark is the widely used ETL tool for processing, indexing and ingesting data to serving stack for search. Milvus is the production-ready open-source vector database. In this talk we will show how to use Spark to process unstructured data to extract vector representations, and push the vectors to Milvus vector database for search serving.
TrustArc Webinar - 2024 Global Privacy SurveyTrustArc
How does your privacy program stack up against your peers? What challenges are privacy teams tackling and prioritizing in 2024?
In the fifth annual Global Privacy Benchmarks Survey, we asked over 1,800 global privacy professionals and business executives to share their perspectives on the current state of privacy inside and outside of their organizations. This year’s report focused on emerging areas of importance for privacy and compliance professionals, including considerations and implications of Artificial Intelligence (AI) technologies, building brand trust, and different approaches for achieving higher privacy competence scores.
See how organizational priorities and strategic approaches to data security and privacy are evolving around the globe.
This webinar will review:
- The top 10 privacy insights from the fifth annual Global Privacy Benchmarks Survey
- The top challenges for privacy leaders, practitioners, and organizations in 2024
- Key themes to consider in developing and maintaining your privacy program
AI 101: An Introduction to the Basics and Impact of Artificial IntelligenceIndexBug
Imagine a world where machines not only perform tasks but also learn, adapt, and make decisions. This is the promise of Artificial Intelligence (AI), a technology that's not just enhancing our lives but revolutionizing entire industries.
UiPath Test Automation using UiPath Test Suite series, part 5DianaGray10
Welcome to UiPath Test Automation using UiPath Test Suite series part 5. In this session, we will cover CI/CD with devops.
Topics covered:
CI/CD with in UiPath
End-to-end overview of CI/CD pipeline with Azure devops
Speaker:
Lyndsey Byblow, Test Suite Sales Engineer @ UiPath, Inc.
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...SOFTTECHHUB
The choice of an operating system plays a pivotal role in shaping our computing experience. For decades, Microsoft's Windows has dominated the market, offering a familiar and widely adopted platform for personal and professional use. However, as technological advancements continue to push the boundaries of innovation, alternative operating systems have emerged, challenging the status quo and offering users a fresh perspective on computing.
One such alternative that has garnered significant attention and acclaim is Nitrux Linux 3.5.0, a sleek, powerful, and user-friendly Linux distribution that promises to redefine the way we interact with our devices. With its focus on performance, security, and customization, Nitrux Linux presents a compelling case for those seeking to break free from the constraints of proprietary software and embrace the freedom and flexibility of open-source computing.
Best 20 SEO Techniques To Improve Website Visibility In SERPPixlogix Infotech
Boost your website's visibility with proven SEO techniques! Our latest blog dives into essential strategies to enhance your online presence, increase traffic, and rank higher on search engines. From keyword optimization to quality content creation, learn how to make your site stand out in the crowded digital landscape. Discover actionable tips and expert insights to elevate your SEO game.
GraphSummit Singapore | The Future of Agility: Supercharging Digital Transfor...Neo4j
Leonard Jayamohan, Partner & Generative AI Lead, Deloitte
This keynote will reveal how Deloitte leverages Neo4j’s graph power for groundbreaking digital twin solutions, achieving a staggering 100x performance boost. Discover the essential role knowledge graphs play in successful generative AI implementations. Plus, get an exclusive look at an innovative Neo4j + Generative AI solution Deloitte is developing in-house.
Driving Business Innovation: Latest Generative AI Advancements & Success StorySafe Software
Are you ready to revolutionize how you handle data? Join us for a webinar where we’ll bring you up to speed with the latest advancements in Generative AI technology and discover how leveraging FME with tools from giants like Google Gemini, Amazon, and Microsoft OpenAI can supercharge your workflow efficiency.
During the hour, we’ll take you through:
Guest Speaker Segment with Hannah Barrington: Dive into the world of dynamic real estate marketing with Hannah, the Marketing Manager at Workspace Group. Hear firsthand how their team generates engaging descriptions for thousands of office units by integrating diverse data sources—from PDF floorplans to web pages—using FME transformers, like OpenAIVisionConnector and AnthropicVisionConnector. This use case will show you how GenAI can streamline content creation for marketing across the board.
Ollama Use Case: Learn how Scenario Specialist Dmitri Bagh has utilized Ollama within FME to input data, create custom models, and enhance security protocols. This segment will include demos to illustrate the full capabilities of FME in AI-driven processes.
Custom AI Models: Discover how to leverage FME to build personalized AI models using your data. Whether it’s populating a model with local data for added security or integrating public AI tools, find out how FME facilitates a versatile and secure approach to AI.
We’ll wrap up with a live Q&A session where you can engage with our experts on your specific use cases, and learn more about optimizing your data workflows with AI.
This webinar is ideal for professionals seeking to harness the power of AI within their data management systems while ensuring high levels of customization and security. Whether you're a novice or an expert, gain actionable insights and strategies to elevate your data processes. Join us to see how FME and AI can revolutionize how you work with data!
Let's Integrate MuleSoft RPA, COMPOSER, APM with AWS IDP along with Slackshyamraj55
Discover the seamless integration of RPA (Robotic Process Automation), COMPOSER, and APM with AWS IDP enhanced with Slack notifications. Explore how these technologies converge to streamline workflows, optimize performance, and ensure secure access, all while leveraging the power of AWS IDP and real-time communication via Slack notifications.
How to Get CNIC Information System with Paksim Ga.pptxdanishmna97
Pakdata Cf is a groundbreaking system designed to streamline and facilitate access to CNIC information. This innovative platform leverages advanced technology to provide users with efficient and secure access to their CNIC details.
Infrastructure Challenges in Scaling RAG with Custom AI modelsZilliz
Building Retrieval-Augmented Generation (RAG) systems with open-source and custom AI models is a complex task. This talk explores the challenges in productionizing RAG systems, including retrieval performance, response synthesis, and evaluation. We’ll discuss how to leverage open-source models like text embeddings, language models, and custom fine-tuned models to enhance RAG performance. Additionally, we’ll cover how BentoML can help orchestrate and scale these AI components efficiently, ensuring seamless deployment and management of RAG systems in the cloud.
Maruthi Prithivirajan, Head of ASEAN & IN Solution Architecture, Neo4j
Get an inside look at the latest Neo4j innovations that enable relationship-driven intelligence at scale. Learn more about the newest cloud integrations and product enhancements that make Neo4j an essential choice for developers building apps with interconnected data and generative AI.