Successfully reported this slideshow.
We use your LinkedIn profile and activity data to personalize ads and to show you more relevant ads. You can change your ad preferences anytime.
Electrical Basics
Test & Measure
Basic Electricity
Basic components of an electrical circuit.
Switch
LoadGround
Hot
Neutral
What is AC & DC
• “AC” stands for Alternating Current “DC”
stands for Direct Current
• AC is denoted by the the words “AC”...
Typical Measurements
• Current
– 1 amp is equal to 1000 milliamps
– 1 amp is equal to 1,000,000 micro
amps
– 1 milliamp is...
• Voltage is the amount of electrical force (pressure) it takes to push
current (electrons) through an electrical conducto...
V AC Voltage
Typical application types:
• Household Outlets, Switches, Doorbells, panels, circuit breakers
• Heating eleme...
Typical application types:
• Automotive Testing
• DC Motor Controls
• Batteries
Check for proper voltage in automotive and...
• Current is the amount of electrons flowing through a circuit.
(1 Ampere = 6.5 billion-billion electrons-per-second flowi...
Typical application types:
• Circuit Board Testing
• Power Supplies; In-Rush Current
• Circuit Breaker Panels
Verify that ...
• Resistance is the amount of “friction” in a wire or circuit.
• Resistance is stated in Ohms
• Resistance is most commonl...
Ω Resistance
Typical application types:
• Ground Circuits
• Resistor Value Verification
• Circuit Board Testing
Check the ...
Typical application types:
• Switches, Outlets, Extension Cords, fuses, and heating coils
• Unenergized Low Voltage Wiring...
Thank you for viewing!
13
Upcoming SlideShare
Loading in …5
×

Sperry Electricity Basics

51,199 views

Published on

This power point gives basic information about electricity.

Published in: Self Improvement
  • Be the first to comment

Sperry Electricity Basics

  1. 1. Electrical Basics Test & Measure
  2. 2. Basic Electricity Basic components of an electrical circuit. Switch LoadGround Hot Neutral
  3. 3. What is AC & DC • “AC” stands for Alternating Current “DC” stands for Direct Current • AC is denoted by the the words “AC” or the symbol • DC is denoted by the words “DC” or the symbol • The majority of applications are AC Ohm’s Law V = I x R volts = amps x resistance Electricity is made up of voltage, current, and resistance. Using the analogy of water flowing through a hose: Voltage is the pressure at the ends of the hose. Current is the water flowing through the hose. Resistance is the diameter of the hose (wire). Basic Electricity
  4. 4. Typical Measurements • Current – 1 amp is equal to 1000 milliamps – 1 amp is equal to 1,000,000 micro amps – 1 milliamp is equal to .001 amps – 1 micro amp is equal to .000001 amps • Milli is depicted as a lower case m in front of the symbol – i.e. mA or mV • Micro is depicted as a µ in front of the symbol – i.e. µA or µV Symbols Basic Electricity V – Voltage A – Current (in amps) Ω Hz NCV F°/C° – Resistance (in ohms) – Frequency – Non-Contact Voltage – Temperature – AC Voltage – DC Voltage – Capacitance – Continuity – AC & DC Voltage – Diode Check
  5. 5. • Voltage is the amount of electrical force (pressure) it takes to push current (electrons) through an electrical conductor (wire). • Voltage can be either “AC” or “DC”. (Alternating Current or Direct Current) • Voltage is what is typically measured at an outlet or electrical box. Typical Testers Used For Detecting or Measuring Voltage Dual Lead Probes Non-Contact Probes V = I x R Volts = amps x resistance Digital MultimetersSolenoid Tester Typical Application An appliance or piece of equipment is not working or an end-user wants to install a new wiring device so they want to find out if voltage is present. What is Voltage?
  6. 6. V AC Voltage Typical application types: • Household Outlets, Switches, Doorbells, panels, circuit breakers • Heating elements, Security Systems Check for energized circuits and verify proper voltage in typical home applications. Why? Incorrect voltage can cause improper operation or premature failure of electrical devices. For example, a home that has a voltage of 137 volts may burn out ceiling fan motor. Alternately, too little voltage can cause failure as well. Symbols
  7. 7. Typical application types: • Automotive Testing • DC Motor Controls • Batteries Check for proper voltage in automotive and industrial circuits. DC is found more in industrial applications than residential. Why? Incorrect voltage can cause improper operation or premature failure of electrical devices. Just as with AC Voltage, too much or too little voltage can cause heating issues within motors and other electric components. DC VoltageV Symbols
  8. 8. • Current is the amount of electrons flowing through a circuit. (1 Ampere = 6.5 billion-billion electrons-per-second flowing through a wire) • The measurement of current is stated in “Amps” or “milli-Amps (mA)” (1000th of an amp). • Current can be either “AC” or “DC”. (Alternating Current or Direct Current) • Current is typically measured with a clamp meter Typical Tester Used For Measuring Current V = I x R Volts = amps x resistance Digital Clamp Meter Typical Application A circuit breaker keeps on tripping so an end user wants to find out the amount of amps being used by an appliance, light fixture or piece of equipment. What is Current?
  9. 9. Typical application types: • Circuit Board Testing • Power Supplies; In-Rush Current • Circuit Breaker Panels Verify that the current draw does not exceed the maximum value of the component. Why? Too much current can cause heating issues that will reduce the life of electric and electronic components. For example, an incorrectly wired fan motor’s life may be reduced by 50% if there is too much current draw. AC/DC CurrentA Symbols
  10. 10. • Resistance is the amount of “friction” in a wire or circuit. • Resistance is stated in Ohms • Resistance is most commonly measured using a multimeter set to the Ohms position • Continuity is a circuit with very low resistance and this is typically tested with a continuity tester or digital multimeter. (a wire that has a break in it does not have continuity) Typical Testers Used For Measuring Resistance / Continuity Continuity Tester Digital Multimeters V = I x R Volts = amps x resistance Voltage/Continuity Testers Typical Application A user wants to test if a fuse is blown or if a power cord is good and does not have a break in it. What is Resistance?
  11. 11. Ω Resistance Typical application types: • Ground Circuits • Resistor Value Verification • Circuit Board Testing Check the resistance values of outlet grounds or resistors found on circuit boards. Measurement is in Ohms. Why? Too much resistance may cause stray current to find another path to ground. For example, a receptacle ground wire incorrectly connected may cause excess heating in the ground wire. Symbols
  12. 12. Typical application types: • Switches, Outlets, Extension Cords, fuses, and heating coils • Unenergized Low Voltage Wiring Check for a continuous circuit. Why? Verify the status of fuses, extension cords, and other types of wiring. For example, landscaping lighting is typically buried around gardens. Digging may actually cut a wire, rendering the circuit useless. Continuity Symbols
  13. 13. Thank you for viewing! 13

×