Research Paper On Changing Oil

Research Paper On Changing Oil
Have you ever change oil? It is usually, time to the oil when the oil light comes on. Most owner
manuals suggest you should change the oil between 3,000 to 5,000 miles. You also can tell that it is
time to change your oil when your gas starts to run out fast. A standard oil change can be performed
by any adult with common sense, and that is physically capable of doing one if health permits. This
procedure can be performed anywhere that is safe. It is essential to change your oil because not
changing it can result in low gas mileage, blowing your motor, and your car could start to smoke
heavily. If you have never changed oil these are the material you will need: A drive up ramp, 5 to 8
quarts of oil of your choice, an oil filter, tire ... Show more content on Helpwriting.net ...
Then put the socket wrench into the square bolt. You will know the wrench is properly on when you
have a snug feel or tight fit. Once you find the correct wrench stop, and go locate your oil pan, and
place the oil pan directly under the motor under the bolt. Start unloosing the bolt, as you do this
make sure the oil pan is directly under the oil that's draining out the car. While the oil is draining,
locate the oil filter it is white and oval. The oil filter is usually located on the side near the back.
After, you locate the oil filter take it off with the oil filter wrench. Once the oil filter is off dispose of
it in the trash, then get the new filter, and fill it up with oil before attaching it back to the motor. This
step is called priming the car. Priming is when you basically jump starting the motor with whatever
you took out. Now the car should be finished draining oil. You can tell its finish from when you look
under the car near the motor and see no oil coming out. Once, that is noticed get the oil bolt and put
it back in tight, but not too tight because that could strip the bolt out. Finally, after the bolt is secured
tightly, start pouring the new oil into the motor. The place where you would begin to pour in has an
oil bucket on its cap. After the all the oil is in the motor put the cap on then you will be finished with
the oil change. You will know the job is correct when you check the oil level with
... Get more on HelpWriting.net ...

Explain How To Do Oil Changes Essay
Have you ever been told you needed an oil change. You probably have thought to yourself "Hmm I
don't want to go pay someone to do a quick job." Doing oil changes are quick and easy. As long as
you have the proper tools to get the job done.
The first part of getting an oil change done is making sure you bought the right oil and filter. To
make sure you have bought the right oil you rather need to check the oil cap or owner's manual.
Sometimes it's only in the owner's manual. When you discover what kind of oil is needed for your
vehicle, then you need to go purchase it. When you're purchasing the oil you also need the filter. In
order to buy the filter you need to know the year, make, model, and engine type. When you go to
your local car part store or even any store that sells engine oil you can ask the people there what
type of filter you need. After you purchase the materials you should be all set to start the process of
changing your oil. ... Show more content on Helpwriting.net ...
Once the car is lifted with the jack you're going to want to place the jack stands under the vehicle.
After the jack stands are placed where they are needed. You're next job is to remove the cap for the
oil which is on tip of the motor. After the cap is removed then you'll want to find the oil plug. The
oil plug is going to be on the bottom of the engine. Make sure you place the oil drain pan underneath
the oil pan before loosening the plug. Once you have placed the oil drain pan underneath the oil pan
you will want to loosen the plug. Once you loosen the plug make sure you take it out completely.
Once the plug is out oil should start draining from the oil pan. While the oil is draining you will
want to locate the oil filter. The oil filter can usually be located on the top or bottom of the engine.
When you find the oil filter you're going to want to twist it off. Remember "Lefty loosey righty
tighty." Make sure the oil pan can catch the falling oil from the

What Makes Your Owner 's Manual?
One of the simplest car maintenance tasks to handle yourself is changing the oil. Along with
replacing the oil filter, your oil change outlay should come in around $25 or typically half the cost of
having your dealer or service center do the work for you.
We'll take a look at how to change your own oil, including the tools you will need and the
environmentally responsible way for disposing the old oil and the filter. This is a job you can
complete within a half hour.
1. Assemble your materials. Your owner's manual will tell you two things about motor oil for your
vehicle. First, what weight or type of oil to use. Second, how much oil you will need. For most
vehicles, a five–quart container is sufficient and cheaper than buying five one–quart cans of oil. You
also need to select the correct oil filter – that information should be found in your owner's manual.
You can also check the chart at your local automotive parts store to find the right oil filter.
2. Gather your tools. If you do not own the right tools to change the oil, you will need to invest in
them or borrow what you need from a friend. You must have a pair of jack stands or ramps,
especially if your vehicle's ground clearance is low. Work gloves, rags, a socket wrench, a funnel, an
oil filter wrench and an oil drain pan are essential. Invest in a new drain plug if the old one is
stripped.
3. Let's get started. Change the oil only when the car is warm or cold. You will be touching
numerous hot spots and the last

Essay On Changing Oil
Cars are important for everyday life and allow citizens to function normally in society. Whether it is
a personal car, Uber, or rental, cars wear and tear daily and need repairs often. This results in time
and money spent on daily maintenance such as gas, and as big as new transmission or engine blocks
after years of driving. There are more common mechanical issues that need fixing periodically
throughout the year such as an oil change. Assuming the average person drives 1,000 miles a month,
it is recommended to change the car oil every three months. The steps to changing car oil follows
the basic deconstruction, replacing, and reconstruction method almost every mechanical problem
follows. The first step in changing car oil is to ... Show more content on Helpwriting.net ...
Before pouring new oil into the engine block, the drainage bolt must be placed back into the car's oil
pan with the 10–millimeter socket wrench. This assures the new oil will not drip out into the old oil.
To replace the old filter with a new one, the new oil must first be applied to the seal of the new filter.
This lubes the seal on the new filter so it will not break due to friction. If it does break, the filter will
leak and a new oil change will be required. Pouring the new oil in is a relatively easy step compared
to all the other steps. To pour the new oil in, the engine oil cap must be removed. The recommended
amount of oil and oil type, which is different for every car, can be found in the owners–manual or on
the car dealer's website. For instance, if the recommended amount of oil is 8 quarts, pour in 8 quarts,
which can be measured by bottles (usually sold in 2 quart bottles), through a funnel into the engine
block. The reconstructing of the car is important because it will let you know if the oil change was
done successfully. Checking the new oil level is crucial to determining if the oil change was done
right or not. Start the car and let it run for five minutes, but make sure the engine oil cap is back on
so oil does not spew everywhere. When the car is turned off, use the oil dipstick, which is in the
engine bay, to check the oil level. If the stick reads that the level is good, the oil

Car Oil Change
How to Do an Oil Change on Your Own Car
If you own a vehicle, you have probably had to change the oil at least once. It is necessary to change
the oil every few thousand miles because old oil becomes contaminated and burnt, which damages
the motor. The average cost of an oil change is between $40 and $60 which, over the life of the car,
the cost can add up. For those that change the oil themselves, they spend at most $20 a change and it
takes very little time. This can save significant funds over a lifetime. Changing the engine oil and
filter is not innate for people. Once you learn how to change the oil, it will serve as a confidence
booster because it takes some mechanical skill to complete the task. The most important steps to
changing the ... Show more content on Helpwriting.net ...
In the winter only, I recommend letting your vehicle run a few minutes before starting. The oil is
thicker when it is colder so when the vehicle runs it will warm the oil, making the oil flow
easier.With the car off, safely elevate the vehicle with a jack or a set of ramps. Next, you want to
align the bucket so it is under the oil pan plug. Proceed to unscrew the plug with the box end
wrench. Be very careful not to be burned by the oil, because it may be hot. Do not drop the plug in
the oil. Completely take off the plug and let the oil drain into the bucket. The next step is to use an
oil filter wrench, to unscrew the old oil filter. The oil filter is usually a three to five inch tall
cylindrical canister located relatively close to the oil pan. When the oil filter is completely off, dump
any remaining oil from it into the bucket. When it is empty make sure to remove the gasket. The
gasket is a rubber ring around the edge of the filter. Once everything is completed, come out from
underneath the vehicle and set aside the old filter. Take the new oil filter out of the box and make
sure it looks like the old filter. Take a little bit of the new oil into clean hands and smear it around
the gasket of the new filter. This is done to "wake up" the gasket so it has an even seal when it is
attached to the vehicle. Make sure to not get any foreign particles into the filter such as sand or dirt.
Bring the new oil filter back underneath

The Importance Of Checking Tire Pressure
Summer is here and that means lots of families are hitting the road! Whether you're going on a
weekend trip to see family or taking a cross–country road trip, having a reliable and well maintained
vehicle will make your trip safer and more fun. When you purchase a used vehicle from ABC
MotorCredit, you can rest assured that your vehicle is dependable and that you'll be supported if you
run into any trouble. Before you hit the road this summer, take care of these simple tasks to keep
your vehicle running smoothly.
Check your tire pressure
Maintaining proper tire pressure is vital to the functioning of your car. Correctly inflated tires are
safer and help you get the best gas mileage possible. Figure out the correct amount of air to put in
your tires by looking on the side of the tire or in your vehicle handbook. Next, use a tire gauge to
check the actual pressure. Make ... Show more content on Helpwriting.net ...
Having emergency supplies can make the experience much easier. A basic emergency kit for a
vehicle should contain a jack for changing a tire, jumper cables, basic tools in a variety of sizes
(screwdrivers, wrench, pliers, etc), roadside flares, a tire gauge, and a flashlight with extra batteries.
Other supplies that may be useful include two quarts of oil, a gallon of antifreeze, extra fuses, a tire
inflator, duct tape, a funnel for adding fluids, and rags or paper towels. These types of supplies can
hopefully enable you to get your car moving until you reach the nearest town or service station.
Don't forget to also pack supplies for your passengers! Bottled water, granola or energy bars, a first
aid kit, blankets, and supplies for children, the elderly, or ill family members may be the difference
between life and death in the event of an accident. Lastly, make sure you include a list of emergency
contact numbers such as roadside assistance and your insurance agent as well as any relevant
account

Cadillac Car Research Paper
Cadillac cars are some of the most exquisitely crafted automobiles on the road today. With luxury
and quality as a paramount priority, Cadillac cars are constructed to last for the long haul. As a
Cadillac owner, you are certainly a person with an eye for quality. In order to keep your Cadillac at
the highest quality possible, it is a good idea to stay on top of the maintenance from the moment you
bring it home. Below are some tips that will help you to enjoy the longest life possible from your
Cadillac vehicle.
Keep Up With Your Oil Changes
While your Cadillac may sound fine and seem to be running great, a failure to keep up with the
manufacturer's recommended schedule for oil changes is a good way to shorten the life of your
precious car. ... Show more content on Helpwriting.net ...
By getting things done like a servicing your transmission and having other parts reconditioned as
outlined in your owner's manual, you will greatly increase the longevity of your Cadillac. All in all,
staying on top of your car's maintenance will guarantee that you have a long enjoyable ownership of
your Cadillac automobile.
In addition to following the maintenance tips above, it is a good idea to take your Cadillac to the
nearest dealer for servicing if it is showing any signs of trouble. Cadillac service dealers have the
highly trained technicians needed to ensure that your car will be on the road for a long time to come.
So call your Cadillac service department today with any maintenance questions you may have. You
are sure to find that they will be very helpful in maintaining your

Research Paper On Trucks
http://forbiddendiesel.com/c–1206928–dodge–ram–2007–5–2015–dodge–6–7l–cummins–parts–
accessories.html Between 2007 and 2015, the Dodge Cummins 6.7L trucks had a diesel rating at
350 horsepower and 650 lb–ft of torque. They were equipped with AS68RD automatic
transmissions. Two more Chassis Cabs were introduced in 2008. These trucks are the workhorses
that take you to and from your job, no matter how far off the path your job is. As you need more
performance from your Ram, you make changes to the diesel performance parts on your truck. We
carry a number of diesel truck parts like air intake systems, emission systems parts and lifts and
leveling kits. For more performance than standard, we offer a range of programmers and chips, as
well as ... Show more content on Helpwriting.net ...
http://forbiddendiesel.com/c–1206698–dodge–ram–2003–2007–dodge–5–9l–cummins–parts–
accessories.html Between 2003 and 2007, the Dodge Ram debuted the newly designed 2500 and
3500 that included major updates like a new frame, powertrain, suspension, interior and sheet metal.
The crew cab had conventional rear doors that came from the Quad cab trucks base. Independent
front suspension was placed on the 1500, but live axles remained on the 2500 and 3500. Another
facelift was in store for the truck in 2006 with the introduction of the Mega Cab with a 6–plus–foot
cargo box and almost two feet of extra cab room. No matter which year your 5.69L is, we have
diesel performance parts to get more from your truck. Flo–Pro turbo back single exhaust pipes and
BD Diesel high idle kits all help your Ram deliver more for your money. We also have engine parts
like belts, pulleys and tensioners, as well as intake manifolds, gaskets and seals. We have cooling
system upgrades that will help keep you cool no matter how much power you add to your truck. At
Forbidden Diesel, we have a professional parts staff that can answer any of your questions. Order
your new diesel truck parts now. http://forbiddendiesel.com/c–1206008–dodge–ram–1989–1993–
dodge–5–9l–cummins–parts–accessories.html In 1989, the Dodge Ram 5.9L V8 was a throttle–body
fuel injection that raised the horsepower by 20. In 1993, the 5.9L was upgraded with multiport
injections, got new manifolds and came with higher compression

Changing Your Oil Changing your oil is a regularly is a really important thing to do to extend the
life of your vehicle and keep it running in prime condition. It is a fairly easy thing to do and you can
save yourself some money by doing it yourself. Oil should be changed every three thousand miles or
three months, whatever comes first. The tools you are going to need are work clothes as an oil
change can get messy. You are also going to need to get oil for your vehicle and an oil filter. The
type of oil you need depends on the vehicle and can be found on the oil cap on top of the engine.
The Filter will be found at your nearest automotive shop such as AutoZone, A person behind the
counter can help you if you don't know. You are also ... Show more content on Helpwriting.net ...
When you are on the ramps you need to set the parking brake and put a brick or block of wood
behind the back tires to prevent the vehicle from rolling back. Once the vehicle is safely in the air
you should get under it and locate your drain plug which will be located close to the oil filter on the
bottom of the oil pan. If you are having trouble finding it consult your owner's manual or google.
Put your catch pan down so that way when you pull the plug the oil goes into the container. Then
find your socket or wrench and take the plug out and set it to the side. While the oil is draining you
should take this time to undo the oil filter, the oil filter just screws on and off and you should be able
to get without any problems. If you cannot get the oil filter of by hand you can get an oil filter
wrench which will do it no problem. Make sure that you catch all the oil from both the drain plug
and the filter in the catch pan. After all the oil has drained from the vehicle you should tighten the
oil plug back in and take the new filter out of the box. You are going to want to fill the new oil filter
with new oil and screw it back in, this kills the time needed for the vehicle to prime the new oil
filter. Never use an oil filter wrench to put on a new oil filter this will make it next to impossible to
get it off in three thousand miles. When you have the plug and filter back on take the vehicle down
to the ground by taking it off the ramps

I Was Driving Home From School Essay
I was driving home from school when all the sudden I see a light flashing on the dash of my car. It
was the oil light telling me that it was time to have an oil change, so instead of driving home I went
straight to the toyota dealership because at the time I drove a Toyota Landcruiser. When I got there
they handed me a clipboard full of information i needed to fill out. It took me a full ten minutes to
complete and even after all that they still handed me more papers to write my signature on, I thought
to myself, "all that for a simple oil change". After finally completing all the paperwork a man took
me to the dealerships waiting room and told me that my oil change should not take long. I was
happy to hear that because I wanted to be on my way. I only expected to be there for 25 to 30
minutes, so after 20 minutes I started looking at the door hoping someone would walk in and tell me
they finished the oil change. Ten minutes later and still nothing. I was getting very impatient and I
was starting to work an appetite. The worst part is they had the food channel on and no remote for
me to change the channel with, so i got up and went to go find a vending machine. Near the car
displays they had a popcorn machine so i scooped myself a small bag full. The popcorn was super
salty and stale and what made it even worse was there was no water to be found. So now i 'm sitting
back in the waiting room hungry and thirsty with a bag of uneaten popcorn, and still no word about
my car. A

MK19 TM 230 23 PAug 2012 059686
ARMY *TM 9–1010–230–23&P AIR FORCE TO 11W2–5–16–2 MARINE CORPS TM
08521B/09761A–OI NAVY SW 363–C3–MMM–020 TECHNICAL MANUAL FIELD
MAINTENANCE MANUAL (INCLUDING REPAIR PARTS AND SPECIAL TOOLS LIST) FOR
MACHINE GUN, 40 MM, MK19 MOD 3, NSN 1010–01–126–9063 (EIC 4AE) MACHINE GUN,
40 MM, MK19 MOD 3, WITH SIGHT BRACKET NSN 1010–01–490–9697 MACHINE GUN, 40
MM, MK19, UPGUNNED WEAPONS STATION (UGWS) NSN 1010–01–362–6513
*SUPERSEDURE NOTICE – This Technical Manual supersedes TM 9–1010–230–23&P dated 30
November 2005, inlcuding all changes. DISCLOSURE NOTICE – This information is furnished
upon the condition that it will not be released to another nation without the specific authority of the
Department of the Army of the United States, that it will ... Show more content on Helpwriting.net
...
Hand injury or equipment damage may result. Be sure to put bolt in forward position before
removing the backplate pin assembly. Failure to observe this warning will result in injury. In case of
a runaway gun, never try to break the ammo belt with your hands. Injury could result. Lower one
charging handle to prevent the gun from firing. To avoid injury, keep fingers clear of the cocking
lever when firing pin fires. Ensure safety slide block is installed in the position shown. If safety slide
block is improperly installed, the thumb safety will not function, endangering personnel.
WARNING FLYING PARTICLES The shuttle spring and spring housing are held under pressure.
Always use the feed slide tool to secure the spring before removing the screws. Failure to observe
this warning will result in injury. Do not attempt to remove three self–locking shoulder screws from
the feed slide housing. Springs will fly out causing injury. The firing pin is under heavy spring
tension. Always shield the tip of the firing pin whenever it is exposed and cocked. This will prevent
injury if the firing pin sear is accidentally depressed. Helical spring is under tension. Shield helical
spring while pulling out pawl rod. This will prevent injury. b 03/15/2011 Rel(1.8) root(warnsum)
wpno(F00103) TM 9–1010–230–23&P WARNING SUMMARY – Continued GENERAL
SAFETY WARNINGS DESCRIPTION – Continued WARNING FALLING PARTS Ensure stow
pin and

Car Advantages And Disadvantages
The benefits are there for people who know their own vehicle and know a little on how to fix certain
things on their vehicles. This could be anywhere from a little more than how to change a tire; which
some people still don't know how to do. Learning how to do basic stuff like change your own oil,
brake pads, and how to identify an electric or motor issue. With the knowledge on auto repairs,
anyone could get themselves out of tough situations, save time, save money, and there are easy ways
to learn. The practice of auto repairs will eventually make you wiser in how to solve problems, save
you from being scammed by another mechanic, be able to make assessments on purchasing a used
vehicle, make you extra reliable, create potential avenue ... Show more content on Helpwriting.net
...
The greatest benefit for learning cars is you could very well be saving money. Things you typically
get serviced on are oil changes and tire rotations. All together it could round up to be a seventy–
five–dollar job. Natalie Spring says, "you'll notice that even though parts only cost twenty–five
dollars, you were charged three–hundred dollars for the mechanic to do the labor to install that part.
That is where they get you, in the cost of labor" (Spring). The majority of what's being charged is
the "service" and not the "product". It's a luxury that I'm sure if people become more
knowledgeable, they'd rather do it themselves and save money.
There are many ways you can learn how to fix car issues. You could find do–it–yourself (DIY)
articles where non–professionals give the basic tips and even motivation. "Car repairs can drain your
pocketbook fast, but you can do a wide range of repairs yourself, regardless of your technical skill.
We're not just talking oil changes; provided you can hold a wrench, you can fix everything ranging
from fuel filters to alternators" (Klosowski). You could learn by working with a professional
mechanic, read it in a book that is revolved around the make and model of your car, or you can
watch a step by step video on You Tube. I would note that it is important to have a book on the year
and model of your vehicle, because it has a lot of info on car parts you would need.
The

Oil Filter Essay
Not everyone here on this planet knows how to be smart and save money. Who wants to pay $50 for
an oil change in their car and also wait at the dealership for an hour while you could be doing better
things. You will learn how to change your oil twice as fast, rather than waiting an hour and get
ripped off. The first thing your gonna do it go to your local auto store and pick up some oil and a oil
filter. Look in the vehicle's owner's manual to see what kind of oil and oil filter it will take and also
how much oil the vehicle takes. Buying oil is what you make it. If you buy cheap oil, your vehicle
won't last as long, but if you buy expensive oil it will have more ingredients to clean and lubricate
your engine while running. Now that you have your oil and oil filter. Find yourself a jack, 6x6
pieces of wood, a pan to catch your old oil, and a 16mm wrench. Get your jack and put it on the
vehicle frame, and crank up. Now begin to put the 6x6 blocks of wood under the frame to hold the
vehicle up. Next up, take your oil pan to catch the used oil under ... Show more content on
Helpwriting.net ...
Next take your new oil filter and hand tighten it on were the old one screwed on to it. Once that is
done, get your new oil and go to the front of the vehicle and under the hood where you unscrewed
the oil cap earlier. Next get a funnel and pour the oil into the engine. Make sure you are checking the
dipstick to tell you exactly how much oil you have. Once it is to the line on the dipstick, start the
vehicle and let it run for three minutes because the oil need to go into the new filter. Turn off the
vehicle and pour the rest of the correct amount into the engine. After that put the cap back on the
engine. Lower the jack and take the blocks out under the vehicle. Put all your tools away and now
you are done.
Changing your own oil to save money and time is a lot better feeling. So next time you need your oil
change done, follow these steps and you can do it

Oil Change Essay
How to Get a Good Oil Change
People need to understand how to get a good oil change. Many car owners believe that this is a
simple service. They also think that anybody can do it. Although these statements contain a few
glimmers of truth, it's not as easy as it sounds. Yes it's a simple service on some automobiles.
However, on some cars and trucks the maintenance procedure becomes more complicated. Auto
repair shops might have to remove belly pans and stone guards to gain access to the drain plug and
filter. In some cases the oil filter is located over the top of electrical components like alternators or
starter motors. In this situation you don't want oil to drip on these electrical devices. Sidebar: a good
mechanical sees this ... Show more content on Helpwriting.net ...
Regular maintenance remains necessary to keep the engine clean inside. Use of high quality filters
and the correct viscosity of oil becomes another critical component of the oil change. This also
becomes one of the rare opportunities that a professional gets to look over the vehicle. Any
outstanding maintenance or safety problems can be discovered during the short time the automobile
is in the shop. A consumer needs to understand what the shop includes in a lube oil and filter
maintenance service. Then they need to make sure they get what they paid for.
Things Included in a Good Oil Change
A good oil change includes checking all the tire pressure including the spare tire. Car makers hide
the space saver spare away to maximize cargo space and reduce weight. When something is out of
sight it's often out of mind of both the driver and the mechanic. A flat tire from debris on the road
remains a common occurrence.
Digging out the space saver spare and discovering that there's no air in it or that it's low is an
aggravating experience. Therefore, a good oil change service will include properly inflating the
spare tire. Many people don't realize, because of its small size, that a space saver spare has twice the
pressure of a regular tire. This means that 60 to 70 psi inflation is necessary for the spare to operate
correctly.
The higher the pressure the more likely a slow bleed down occurs. A really conscientious mechanic
will go one step further and make

Changing Car Engine Oil Research Paper
Changing Car's Engine Oil
"Money doesn't grow on trees." people use this proverb in their daily conversations to say that
people should not waste money or spend a lot. Wasting money is considered as a bad habit for any
person, and people try very hard to save their money for their children and to build their futures.
Some people work very hard in their lives to make as much money as they can. Trying to find new
ways to save money is not very difficult. People already know some of them, and changing the car's
motor oil is one of the best ways that can save some money within a long period. People can save
from $ 25 to $ 35 when they do it by themselves. Everyone knows this amount of money will go to
the person who will change the oil. People ... Show more content on Helpwriting.net ...
First, Opening the oil filler cap and putting the clean funnel in the oil filler hole on the top of the
engine and start filling the car up with oil. Adding the oil slowly and the car will need four or five
oil bottles, depending on the car engine size. Once the oil is all in, screw on the oil cap and close the
car's hood. Second, the car engine needs to be started and works for a short time, about 3 to 5
minutes. After that, checking the oil in the motor to make sure the oil is at the recommended level
for the car. Next, person has to check if there is any leaking from the oil drain plug or the oil filter.
The old oil needs to be disposed by taking it to a proper disposal location. Transferring the used oil
from the drip pan into a couple of empty old juice jugs. People will need to use their funnel and a
helping hand to make the transfer and screwing on the lids. Putting the jugs in the back of the car,
and drop them off at local quick lube and giving them the old oil

Essay about How to Change Your Vehicles Oil
How to change your vehicle oil
Informative Speech
I. Introduction
A. When you're driving down the road and that mileage reading on your dashboard reaches 3000
what do you? The first thing that pops in your head is there goes another 50 dollars for an oil
change. There are about 450 million cars that travel the streets and roads of the world (Automobile).
B. Almost everyone that owns a vehicle has had to take their vehicle in to a mechanic to get their oil
change on their car. But there's another way to do this its called "DO IT YOURSELF".
C. I've been doing my own oil changes since I've owned my first vehicle. As well as every other
vehicle that the own would allow me to do it on.
D. I will be explaining the steps on changing the ... Show more content on Helpwriting.net ...
Consult your owner's manual for the exact location. iii. Step 3: Place the oil drain pan under the plug
and loosen the plug with a socket wrench. Remember: turn counterclockwise to remove bolts. iv.
Step 4: Remove the plug by hand. Be prepared for the rush of hot oil!
v. Step 5: Let the oil drain into the pan. Hold onto the plug.
D. Installing New Oil and Cleaning Up: i. Step 1: Locate the oil filler cap on top of the engine.
Remove it. ii. Step 2: Place the funnel in the opening and pour in the new oil. Typically, you will use
4 to 5 quarts of oil. Check your manual for the correct oil capacity. iii. Step 3: Replace the cap when
you're finished. iv. Step 4: Run the engine for a minute, and then check the dipstick. Add more oil if
necessary. v. Step 5: Check the area around the oil drain plug and the filter for oil leaks. Tighten the
plug or oil filter if you find leakage (ehow.com).
III. Conclusion. A. I explained two main steps to change your oil in your vehicle. i. I explained the
steps to draining the oil and changing the oil filter. ii. I explained the steps to installing new oil and
cleaning up. B. One should change their oil every three months or every 3000 miles to prevent
buildup of corrosive byproducts of combustion which could erode metal parts and accumulation of
dirt in the oil from debris caused by blow–by

My Ecology Project To Tune Up My Mom's Car
My ecology project is to tune up my mom's car to make it run more efficiently, therefore polluting
less. I will do it at my house, where there are the necessary tools to change the oil, air filter, and
other parts. I will change the oil, air filter, cabin air filter, and radiator fluid. Changing these will not
only make the car have more performance, but also will make the engine run more efficiently,
reducing pollution. I will change all parts at once, most likely occurring on September 23rd. To
correctly maintenance the car, there are several steps to replace each part. To change the oil, I will
remove the drain plug with a ratchet and drain the oil into an oil pan. Following, I will replace the
drain plug and put new oil into the car. To ... Show more content on Helpwriting.net ...
This will be achieved by making the engine run more efficiently, thus using less fuel, thus emitting
less waste. The Environmental Protection Agency states that about 29% of greenhouse gas
emissions comes from transportation. If all vehicles are serviced regularly, this percent will
decrease. The decrease in greenhouse gas emissions will slow global warming and make less
pollution. This will help our desert environment by making the air cleaner.
My relationship with the environment will improve. I will become more aware of the effects of
automobiles on the environment. In addition, I will be more inclined to make more environmentally
friendly decisions due to the experience and knowledge gained from taking part in this project. This
includes servicing cars more often and using less amenities that increase greenhouse gasses and
pollute our skies.
My health will improve after doing this project. Decreasing pollution will make the air healthier to
breathe. Not only will it be healthier for us, but it will improve the health of the plants breathing the
air in our desert. This will cause them to make oxygen more efficiently decreasing greenhouse gas
effects. Having healthier plants will also improve the health of the animals who eat the plants, and
the animals that eat the

Persuasive Speech On How To Change Cars
Who here needs a break from their job? I certainly know that I do! Now think about your vehicle–
that thing that constantly gets you from one place to another, without you having to think about it
too. Doesn't your vehicle deserve a break too? Well luckily, today I am going to teach you how to
treat your car to a spa day. In other words, I'm going to explain how to change the oil in your car. As
some of you may know, there are variances depending on the vehicle you drive. Today, though, I
want teach you the general concepts behind the benefits of regular oil changes, the tools needed, and
the actual steps required to change oil. First of all, the benefits of regular oil changes are almost
insurmountable. Surprisingly, though, these benefits are not just associated with your car. Regular
oil changes are one of easiest ways to extend your vehicle's life. In return, this saves you the time,
money, and inconvenience of breakdowns and repairs. Also, according to Meineke.com, other
benefits of regular oil changes include, "improved gas mileage, better engine performance, and less
vehicle emissions" ("Top Five Reasons Oil Changes Save Vehicles"). Furthermore, Time.com says
having the skills and knowledge to "do it yourself" will save you approximately $25 per oil change
(Renzulli). Next, I will identify the tools, parts, and materials needed to perform an oil change. The
basic items needed are: a wrench, two drain pans, funnel, oil, rags, and an oil filter. I highly
recommend

Changing Oil in Your Car Essay
Changing Oil in Your Car
When the average person's car needs an oil change we drive to a Quick Lube and have it done in 20
minutes. Another alternative would be to change the oil your self, this is a fairly simple process,
most people with some common sense and some basic hand tools can do it at home on a weekend.
The first step is finding out how much oil your car holds and what kind of oil filter fits on your cars
engine. Your car's owner's manual will have a capacity section in the back, down the list till you
come to the engine oil capacity, and the chart will list the number of quarts that your car needs. Also
on most new cars when you can look on the oil cap it should state the oil weight which is
recommended by the cars ... Show more content on Helpwriting.net ...
Once you have the car in the air you will want to put some jack stands under each side and lower the
car down on these, this will prevent the car from falling on you if the jack where to collapse, since
jacks are only designed to pick the car up, not support it all day. Once the car is safely on the jack
stands, you are ready to change the oil.
First, you need to remove the oil fill cap under the hood so the oil will flow out freely. Be sure that
you have a container for the used oil later; take it to recycle centers which are usually located around
town. Remember that it is now illegal to dump oil anywhere. Next find the drain plug, which will be
located on the bottom of the engine block. It is the only plug located usually in the middle of a black
pan in the front of the vehicle. Be careful that you have the right plug because some transmissions
are also equipped with a drain plug. Once the plug has been located, find the right size socket or
wrench to fit it, and be careful not to round of the head of the drain plug when you are removing it.
Then let the oil drain in to your container. When the pan has drained replace the plug, but do not
over–tighten it because you can strip the treads out of pan. Next, you need to find the oil filter,
which should be located on either side of the engine block. Then take the oil filter wrench and put it
around the filter and remove the old filter. Then take your new filter and take a little

Essay On Changing Car Oil
While most people nowadays, rarely think about changing their car oil. But little do they know, that
regularly changing a car's engine oil is one of the most important things you can possibly do to keep
a car running without any problems or mishaps. Without regular oil changes, the old oil inside of a
car, will break down and clog a car's oil filter, causing a hefty price for repairs and replacements.
The general population, might not know this, but changing the oil of a car is both inexpensive and
easy.
The change begins by driving the car into a driveway or a spot with enough allocated space to work
beneath the vehicle and outside the vehicle. This is done to make sure, that an individual does not
cause any accidental damage to a person, ... Show more content on Helpwriting.net ...
As soon as the oil cap bolt has been screwed back on, new oil has to be added. Locate the the fill
hole at the top of the engine. If location cannot be verified, look to the left of the engine, and there
should be a cap. Before anything is done, it is heavily recommended that vehicle capabilities are
checked in the owner's manual, to insure how much oil the vehicle can take. Too much oil intake
may cause blockage, so please be wary.
Once the new oil has been inserted, it is recommended that the engine is turned off and on to double
check that everything is running smoothly with the oil pressure. This can be verified, by checking
the red engine light turn off and on after startup. If that is not the case, then a bolt is not tightened
properly, and is oozing out liquid or oil.
As another verification method, the dipstick can be pulled out of the vehicle to double check the
pressure. This is located to the bottom left of the engine. It generally looks like a long metal rod.
Simply pull this out, and check to see if both holes on the bottom of the stick are shaded in with oil.
If this is the case, then a successful oil change has been

Exploring Corporate Strategy
ECS8C_C01.qxd 22/10/2007 11:54 Page 597 CASE STUDIES ECS8C_C01.qxd 22/10/2007
11:54 Page 598 ECS8C_C01.qxd 22/10/2007 11:54 Page 599 Guide to using the case studies The
main text of this book includes 87 short illustrations and 15 case examples which have been chosen
to enlarge specific issues in the text and/or provide practical examples of how business and public
sector organisations are managing strategic issues. The case studies which follow allow the reader to
extend this linking of theory and practice further by analysing the strategic issues of specific
organisations in much greater depth – and often providing 'solutions' to some of the problems or
difficulties identified in the case. There ... Show more content on Helpwriting.net ...
Pharmaceutical Industry – global forces at work in the ethical pharmaceutical industry. TUI –
competitive forces in the travel industry. HiFi – how can small players survive changing markets?
Amazon (B) – latest developments in a successful dot.com. Formula One – developing the
capabilities for competitive success in a hi–tech industry. Manchester United – clash of expectations
in the football world. Salvation Army – strategic challenges for a global not–for–profit organisation
with a mission. Bayer MS –

Explain How To Change The Oil In A Car
How to change the oil in your car Oil lubricates the moving parts that are within the engine. It also
absorbs heat so that the engine doesn't overheat. Your oil needs to be changed every 3,000 to 5,000
miles. If you would rather change it yourself instead of taking it in somewhere to be done, follow
these steps. Step Action 1. Put the car up on jacks. A. Put the jack under the car so that the drain
plug is angled down. 2. Remove the filler cap. Note: This is under the hood, on top of the engine. 3.
Place an oil pan under the car to catch the old oil. 4. Remove the oil plug. A. Get under the car and
find the oil plug under the engine. B. Use a wrench to start loosening the oil plug if it is too tight. C.
Keep pressure pushed

Igbo Dictionary
onaryDictionary of Ònìchà Igbo 2nd edition of the Igbo dictionary, Kay Williamson, Ethiope
Press, 1972. Kay Williamson (†) This version prepared and edited by Roger Blench Roger Blench
Mallam Dendo 8, Guest Road Cambridge CB1 2AL United Kingdom Voice/ Fax. 0044–(0)1223–
560687 Mobile worldwide (00–44)–(0)7967–696804 E–mail R.Blench@odi.org.uk
http://www.rogerblench.info/RBOP.htm To whom all correspondence should be addressed. This
printout: November 16, 2006 TABLE OF CONTENTS Abbreviations:
................................................................................................................................................. 2 Editor's
... Show more content on Helpwriting.net ...
12 5.1 Alphabet
............................................................................................................................................... 12 5.2
Double vowels ......................................................................................................................................
13 5.3 Syllabic nasal
....................................................................................................................................... 13 5.4
Tones.....................................................................................................................................................
13 5.5 Word division
...................................................................................................................................... 13 5.6 A note on
'y' ......................................................................................................................................... 14 6.
Grammatical sketch
.................................................................................................................................. 15 6.1 Parts of
speech ..................................................................................................................................... 15 6.2
Verbs.....................................................................................................................................................
17 6.2.1. Types of verbs

Demonstration Speech
Demonstration Speech
HOW TO CHANGE THE OIL IN A CAR
General Purpose: To inform
Specific Purpose: To demonstrate to the audience how to properly change the oil in a car.
Central Idea: Changing the oil in your car is a simple task that one can easily perform at home.
INTRODUCTION
I. When you're driving down the road and your odometer trips another 3000 miles you're probably
thinking there goes another 30 dollars for an oil change.
II. Changing the oil in your car is a simple task that one can easily perform at home.
III. All you have to do is gather the proper equipment, drain the old oil, replace the oil filter and fill
the car with new oil.
IV. I have been changing the oil in my car since I started driving when I was ... Show more content
on Helpwriting.net ...
Start the engine. 1. Check for any drips or leaks. If the filter or drain plug aren't tight they may leak
slowly. G. Last check your oil levels to make sure you have enough oil in the car. 1. Remove the
dipstick and wipe it clean. 2. Put the dipstick back in, and then remove it again. 3. You can
determine if the oil levels are full, if the oil comes up to the upper hole or hash mark on the dipstick.
H. Check to make sure no tools or towels are left and then close the hood. (Transition: That
concludes all the steps to changing your oil. ) CONCLUSION
I. Overall, it isn't very hard to change the oil in your car. Just have the proper equipment, drain the
old oil, and replace it with new oil.
II. It is recommended you should change your oil every 3000 miles to maintain the life of the motor.
III. Now next time you're due for an oil change you might be able to save yourself some money and
change it yourself.
Works Cited
Edmunds, Dan. "How to Change Your Oil." Edmunds Answers. Edmunds, 22 Dec. 2011. Web. 02
Oct.

HOW TO CHANGE YOUR OIL SPEECH OUTLINE
COM 181–9:30–10:15 Thursday September 26, 2013 How to change your oil General purpose: To
inform Specific purpose: To inform the audience on how to change the oil in a vehical. Central Idea:
Changing ones oil in a vehicle is a skill that could save you a lot of time and money I. Introduction
A. When you're driving down the road and that mileage reading on your dashboard reaches 3000
what do you? The first thing that pops in your head is there goes another 50 dollars for an oil
change. B. Almost everyone that owns a vehicle has had to take their vehicle in to a mechanic to get
their oil change on their car. But if you want to save time and money you can always do it yourself.
C. My father ... Show more content on Helpwriting.net ...
iii. The oil should roughly take ten to fifteen minutes to drain completely. When the oil stops
draining your ready to remove the oil filter. Just like before with the plug place the oil drain pan
directly under oil filter. This is done because almost always their will still be a little left over oil in
the filter. When removing the filter you want to turn the oil filter counter clockwise to release it from
your vehicle. iv. As soon

Process Analysis
Changing your engine oil is one of the single most important vehicle maintenance acts you can
perform. Over time the oil breaks down and no longer performs its job the way it did when it was
new. Your engine 's oil helps absorb heat from the engine and lubricates moving metal parts that
would otherwise grind together. As you drive, the oil pump circulates oil within your engine and the
oil filter catches the deposits that build up over time. The oil filter performs its own type of car
maintenance by keeping the oil clean. But as the oil gets older, the number of deposits in the oil
continues to build and the filter is unable to extract all of the material. When this happens, the color
of the oil changes and it indicates the oil should be ... Show more content on Helpwriting.net ...
Typically, most engines take between 4 and 6 quarts. Use a funnel to channel the oil to keep it from
spilling out onto the engine. Once you 've added the correct amount of oil, lower the car off of the
ramps or car jacks. It may take a few minutes for the oil to reach the bottom of the pan because it 's
cold and moves slower than hot oil. The oil level should be just below the "full" mark on your
dipstick.Once you 've determined that you have the correct amount of oil added to your engine, turn
the car on and run it for about five minutes to allow the oil to circulate. Once you 've done this,
check for any oil leaks before you clean up.
That is how you change your oil a simple process that saves you money and keeps your car running
for as long as you need

How to Change Oil in a Car Essay
How to Change Oil in a Car
Owning a car is usually a significant investment for an individual. Changing the oil on your car
plays an important part to help keep it functioning at peak performance and to ensure that your
vehicle last for many miles. You might wonder how often does the oil need changing. Well,
manufactures advise that the oil is changed every 3,000 miles or every three months, whichever
occurs first. Changing the oil is not an extremely difficult task, but it is always good to have
someone else there, who has done this before, to help if needed. I would also suggest finding an
outfit you wouldn't mind getting dirty and a pair of rubber gloves to keep your hands clean.
The key to keeping any task, especially this ... Show more content on Helpwriting.net ...
Two empty milk containers should do the trick. If you don't have any laying around, just use the
empty oil bottle containers. A funnel works well when transferring the old oil into the containers.
Last, some old rags are good for cleaning up spills.
Now that all the materials are gathered, we can change into our outfits and get started. Make sure
that your car is parked on a level surface, rather than a hill or an inclined driveway. Start your car
and let it run for about 10 minutes. This process allows the oil to warm up which makes it drain
quicker than cold oil. Shut the car off and engage the parking brake. Place jack under vehicle lift
points, located on the frame rails just behind the front tires. Raise the car by pumping the jack up
and down, giving enough clearance to slid the jack stand under the car. Place the jack stand under
the frame or anywhere sturdy enough to support the weight of the car. Adjust the height of the stands
to allow room for you to get under the car. After jack stands are positioned, slowly lower the car
onto the stands by turning the pole on the jack to left.
Now its time to grab your drain pan and slide under the car to located the oil pan. It is located on the
lowest, very bottom part of the engine. There is a plug, which is a bolt, located on the bottom part of
the oil pan. Make sure you are not directly underneath the plug. The drain pan should be directly
under it. Use a socket wrench or an adjustable wrench to

The task of changing oil in your car is neither as easy as threading a needle nor as difficult as
building a rocket. But this is the least you can do to serve your car at home if you only know and
follow a simple procedure, precautions and tips. Following which can not only save you from the
extra trouble of going to the service station and waiting for an hour or half till the oil is changed but
it also helps you save the money you would pay unnecessarily to the service man at fuel station and
buy him the accessories every time you go to get the oil changed. Moreover, it is always good to
venture out and see how much can you rely upon yourself for the maintenance of your car. The
following is how you do it. Before you change the oil, ... Show more content on Helpwriting.net ...
If the manual you were given with your car is lost, you may search for the appropriate oil type,
weight and oil filter online. There are many tools available online which help you find it. There are
two more very important tasks to be done before the actual oil change process. The first is spreading
a polythene sheet under your car engine so that the floor may not be greasy by the spilling of oil
during the process and the second is grabbing a chair or a table near your car engine to keep the tool
kit consisting of a wrench set, a rubber mallet, a box–end wrench for the plug, jack stand, funnel,
paper towel, rubber gloves and a pan to trickle old oil in so that they can be made readily available
when needed. Now keep the car jack right in the front center of the car and jack it up. Always
remember to support the jack with a stand so that it doesn't fall on you while you work underneath.
It is risky to work under a car supported only with a jack. Then lower it down to the level you are
convenient at while working underneath the car easily. Make sure that your car is set in the parking
mode. Once the car is lifted up, put your safety glasses and rubber gloves on as the oil coming out of
the car can be very hot. As mentioned earlier you should let the car run for a few minutes if it is cold
so that it can get warmer and the sludge trickles down easily. Running car for about ten minutes
before changing oil is recommended by many car experts. Unplug the drain

Changing The Oil In A Car's Engine
How To Change the Oil in your Car's Engine
Automobiles are American's second largest investment after real estate. It is impoprtant to
understand how to keep your car performing at its best.
The major components of a car consist of the engine, transmission, brakes, suspension, and tires.
The purpose of this essay is to guide you through the process of changing the oil in your car's
engine.
An oil change is recommended every 3,000 to 5,000 miles depending on your driving style and
conditions. Your car is more likely to need an oil change at 3,000 miles if you live in a metropolitan
area where you face stop–and–go traffic, polluted air, and very hot temperatures.
Oil change is very easy to do; you don?t always have to go to ... Show more content on
Helpwriting.net ...
The area is shown on most car manuals.
4. Jack the car up about a foot to a foot and a half. Use the jack stands and put them on both sides of
the car. ** This is a very important procedure; in case the jack fails (unlikely but can happen) you
have something to hold up the car.
5. Look under the car to find your oil reservoir, use the socket wrench to remove the nut. Before you
do this, you should have an oil pan ready to keep the dirty oil. After you unscrew the nut, you should
see a stream of motor oil draining out of the oil tank. Allow this process to occur for 5–10 minutes
and make sure the oil is going into the oil pan. This is the most annoying part of the entire procedure
because sometimes things can get messy. Also look for the oil filter and twist in open. We are going
to replace it with a new one in our next step.
6. Check in after 10 minutes, if you don?t see anymore oil dripping out, screw the nut back in tightly
and also screw on the new oil filter. Using a little bit of motor oil on the rubber gasket will ensure a
tight fit.
7. You are now almost done; make sure you have pulled everything out of the bottom of the car.
Now release the jack and let the car slowly come down to the surface. Open the oil cap and pour in

the quarts of motor oil into the oil tank. The amount is specified in the owner?s manual. Close the
oil cap and proceed to start your car. Shut the car off;

The Benefits Of Heavy Machines
Heavy machines are used on a daily basis when it comes to the planting and harvesting of crops.
Combines are used to harvest crops and they are pushed to the limits during harvest. These machines
are used vigorously for the majority of their operating time. Being driven all day, they need to be
lubricated to prevent wear. On each harvest day, the machinery needs to be fueled and each of the
gears, shafts, and bearings need to be well lubricated to prevent damage. If the machines are not
correctly lubricated, there is probability that there could be damage. There is more to servicing then
the lubricating aspect. There is also the fueling and cleaning of the engine compartment. Combine
preparation and lubrication is a task that has to be ... Show more content on Helpwriting.net ...
To check the oil of a combine, the engine must be running for two minutes prior to checking. When
the engine is warm, turn the engine off. When checking the oil, first unscrew the dipstick and wipe it
off with a clean rag. Then screw it all the way in and back out to check the level on the dipstick.
Low levels of oil can indicate a problem in your engine. Oil is added to the engine through the same
hole that the dipstick is secured in. Too much oil added to the engine could cause harm to the
engine. If there is any dirt or water enters, there could be serious damage to the engine. If any dirt or
foreign materials get into the oil, drain the oil by opening the valve near the bottom of the engine.
Oil will then run out of a hose located on the bottom right hand side. Once the oil is drained, close
the valve and fill the engine with fresh oil to the right amount on the dip stick. After the engine
components are serviced, inspection of the clamps and hoses are vital. If a hose has any cracks or
bulges, it will need replaced as soon as possible to prevent damage. If one of these hoses breaks, oil
could spray and cause the engine to overheat or catch fire. If a clamp is loose, or is damaged it also
needs to be replaced. Inspecting these can help prevent damaging in large scale. After the engine
compartment is fully inspected and cleared, the grain bin is the next area for inspection. The first
thing to inspect is the auger pointed at

Engine Removal Research Paper
The removal of a internally damaged engine from your personal car or truck may seem like a
daunting task, but in reality, with the proper tools, equipment, and work space, it can be done within
a 6 hour time frame. Having the proper space to pull the motor is the number one key to the engine
removal. There will be components of the motor that will have to be disassembled at certain periods
during the removal process and if there is no space to lay the parts, then where are you going to put
the motor? The proper tools and equipment is another major concern of an engine removal. Not all
the bolts and nuts that hold the motor and its components together are not always the same size, and
sometimes certain bolts and nuts are in tight spaces so only certain sized ratchets or wrenches will
fit to loosen them. Also, there are specialty tools for loosening ... Show more content on
Helpwriting.net ...
Usually 2 separate pans are needed. One is for oils, such as motor oil and power steering fluid, and
the other is for antifreeze. If the antifreeze fluid is relatively new, it can be saved and reused. The oil
on the other hand should not be reused because if the engine is internally damaged, there may be
small bits of metal in the oil that cannot be seen as well as sludge that can build up making a motor
work harder. Normally the oil filter is left on to keep oil from dripping. Once all the oil and
antifreeze are drained, replace the plugs and tighten. Also, if the vehicle has a working air
conditioner system, a recovery machine is needed to recycle the Freon out of the system. The system
is under high pressure and Freon depletes the ozone layer, so only a certified technician can handle
Freon. Even if your AC compressor is locked up, the system may still have Freon still in its lines. If
you are planning an engine swap, it is best to have a local auto shop recover your Freon for you
before starting the engine removal

Northwest Territories Box 1320 Yellowknife NT X1A 2L9 Canada
Public Works and Services Safety Program
ACCIDENT PREVENTION MANUAL
2002 Public Works and Services Government of the Northwest Territories Box 1320 Yellowknife
NT X1A 2L9 Canada
If you have comments or corrections, write to PWSfeedback@gov.nt.ca
1. PWS Safety Policy
PWS is committed to providing safe and healthy working conditions and to promoting positive
attitudes toward safety and health. Department managers will work actively with employees and
contractors to identify and correct unsafe or unhealthy working conditions and practices. PWS
recognizes that workplace safety is a shared responsibility. Everyone is responsible for the
prevention of accidents.
PWS Accident Prevention
September 2002 Page 1
2. ... Show more content on Helpwriting.net ...
PWS Accident Prevention
September 2002 Page 6
Drive with headlights on at all times. Drive at speeds that fit the weather, traffic, road and vehicle.
Don't drive when conditions are hazardous, except for an emergency. Take the shortest and most
direct route.
After Driving Park in GNWT parking spaces, where provided. Switch off the ignition and remove
the keys when you leave the vehicle. Lock the doors. If the temperature is below –20ºC, plug the
vehicle in. Keep idling time to a minimum. If the vehicle needs repairs, tell your supervisor. Keep

vehicle clean inside. Keep vehicle logs up to date. Return shared or loaned vehicles and keys
promptly. Remove your personal belongings and garbage after using shared or loaned vehicles.
In Case of Accident: Report all accidents to your supervisor and complete a Vehicle Accident Report
form as required by Risk Management. Report to the RCMP accidents with injury or damage over
$1000. (Follow the procedures in Chapter 10 – Accident Reporting.) If damage is caused by your
carelessness, you may have to pay for repairs or damages, and may be disciplined.
Supervisor Responsibilities
When hiring for a job that includes a driving requirement, ask to see their driver's licence. Make
sure they have the right class of licence for the vehicle they would be driving. Make sure your
employees and contractors follow the PWS rules when using vehicles for government business.

Essay On How To Change Your Own Oil
Learning to change your own oil is an excellent way to save money and increase your mechanical
know how. Changing your own oil can save you several hundred dollars a year. It also prevents
premature wear of parts, which can cost even more money to repair. Before you begin, make sure to
understand the risks involved. Getting under a car can be extremely dangerous without the proper
safety equipment. An unsupported car can fall and seriously injure or kill you. Hot oil can burn you
as well, so make sure to give the car some time to cool off before you start. Begin by gathering the
necessary tools and supplies. For tools, you'll need: a metric or standard socket set and wrench
(depends on the make of your vehicle), jack and jack stands, oil ... Show more content on
Helpwriting.net ...
Make sure to keep the drain pan close by. The oil will begin to drain once the drain plug has been
removed. Next, remove the oil filter. This should be located near the oil drain plug. If you have an
oil filter wrench, use this to remove the filter. Otherwise, you should be able to remove it by hand.
After letting the car sit for a minute or two, the oil should be fully drained. Reinstall the oil drain
plug. Use a torque wrench set to 30 ft./lbs. if you have one. Otherwise, tighten it until snug. Then
install the new oil filter. First, lubricate the inner threads, then lubricate the rubber seal around the
edge of the filter. Next, fill the filter with fresh oil. Then tighten the filter by hand until snug. Once
you've installed the filter, begin to fill the engine with oil. The manual will specify how much oil is
needed. Most passenger cars require four to five quarts of oil. Find the oil fill cap on the top of the
engine and remove the cap. Use a funnel to fill the engine up with oil. After filling the engine with
the correct amount of oil, run the car for a few minutes to allow the oil run down into the engine.
Then, let it sit for 30 minutes to get an accurate reading. After the car has sat, remove the dip stick
and check the oil level. It should be between the two dots. If necessary, add more oil. If you're
changing the oil in a newer vehicle, you'll most likely have to reset an oil life monitor on the
dashboard. Consult the vehicle manual for the procedure.

Research Paper On Changing Oil

Recommended

Recommended

More Related Content

Similar to Research Paper On Changing Oil

Similar to Research Paper On Changing Oil (20)

More from Amanda Reed

More from Amanda Reed (20)

Recently uploaded

Recently uploaded (20)

Research Paper On Changing Oil