Electronic test equipment, Oscilloscope, Spectrum, Analyzer ,DMM

NO Maker Model Description
1 Advantest R3261D 9kHz-3.6GHz with 1Hz maximum resolution. Specialized signal measurement modes including RF power.
2 AC/DC EL300 Electronic load. 300Wt max. Hi/Low range, small size
3 Acterna TTC-310 Protocol analyzer with DS1/DS3 interface; opt 1 and 3
4 Acterna 8630 Protocol analyzer GSM, GPRS, CDMA, UMTS, V5, ISDN, SS#7. Operating system not loaded! E1/T1
interface available
5 Acterna 4000 Communication analyzer. Two interface slots allow mixing of different test modules in one analyzer.
6 Acterna 6000A Communication analyzer. Inteface modules are available.
7 Acterna 6005 GPIB Inteface module for TTC6000A analyzer
8 Acterna 40200 RS-449 interface for the TTC 4000, 6000 analyzers
9 Acterna 40202 V.35 Interface module for TTC 4000, 6000 analyzers
10 Acterna 40204 Interface module for TTC 4000, 6000 analyzers
11 Acterna 40895 T1 channel monitor for TTC209
12 Acterna 41440 T1/FT1 interface for the TTC6000 analyzer. Unused condition
13 Acterna 41440A T1/FT1 interface for the TTC6000A analyzer.
14 Acterna 41704-01 V35 inteface plug-in for TTC 6000
15 Acterna 2262/90.01 Acterna E1/T1 Module for the Acterna 8630 analyzer
16 Acterna ANT-20SE With STM-64 and OC-192 Interface module. Contact us for the list of installed options.
17 Acterna 310 Communication Analyzer. With option S.. Options are available separately
18 Adtech AX/4000 10GB Ethernet test system. Incl. 16slot chassi, 401427 control module, 403100 Generator/Analyzer, 403335
Test interface
19 Adtech 403335 Test interface for Adtech AX/4000 system
20 Adtech 401427 Control module for AX/4000 system.
21 Adtech 403100 Generator/Analyzer module for AX/4000 system.
22 Advantest TR4131 10kHz-3.5GHz portable spectrum analyzer. GPIB, RS-232, Video out, Audio jack. .
23 AgiHP 6443B 0-120V, 0-2.5A. Constant voltage or current. Fine adjustment controls.
24 Agilent 1670D 136 channel, 100MHz/250MHz, Deep memory logic analyzer. 1MB per channel, Ethernet port
25 Agilent 1672E 68 channel, 100MHz/250MHz, Deep memory logic analyzer. 1MB per channel Hard drive, Ethernet port
26 Agilent E4406A Communication Analyzer. Option BAC ( CDMA measurement personality )
27 Agilent 4155A Repair Service.
28 Agilent 4155B Semiconductor Parameter Analyzer. 4 SMU's and 2 VSU's, Color Graphics.
29 Agilent 4156B Semiconductor Parameter Analyzer. 4 HiRes SMU's and 2 VSU's, Color Graphics.
31 Agilent 4155B Repair Service.
32 Agilent 4155C Repair Service.
34 Agilent 4156C Repair Service.
35 Agilent 86130A BERT Analyzer 3.5GigaBit/s. Pattern generator and Error Detector. Windows GUI.
36 Agilent 33120A 15MHz Functions/Arbitrary waveform generator. New in a box!
37 Agilent 8493A 12.5GHz attenuator. SMA connectors. Available values: 3,6,10,20,30dB
38 Agilent 8494B Programmable step attenuator, DC-18GHz, 11dB, "N" connectors (opt 002)
39 Agilent 8494G Programmable step attenuator, DC-4GHz, 11dB, SMA conn. 5VDC. opt 002, 011
40 Agilent 8495G Programmable step attenuator, DC-4GHz, 70dB, SMA conn.. 5VDC opt 002, 011
The following items (ID-SS8267-1-1) are subject to prior sale without notice. These items are only for end users.
sales@semistarcorp.com 1 of 37 Email us for the availability pls. Appreciate your time!

41 Agilent 8495H Programmable step attenuator, DC-18GHz, 70dB, SMA connectors (opt 002)
42 Agilent 33320H Programmable step attenuator, DC-18 GHz, 11dB, SMA conn. Sold as set of 2
43 Agilent 33321H Programmable step attenuator, DC-18 GHz, 70dB, SMA conn. Sold as a set of 2
44 Agilent 33322H Programmable step attenuator, DC-18 GHz, 70dB, SMA conn., 24VDC.
45 Agilent 33322H Programmable step attenuator, DC-18 GHz, 70dB, SMA connectors, 24VDC.
46 Agilent 10833A GPIB/IEEE-488 Cable. MSRP . Multiple quantity discount.
47 Agilent 10833B GPIB/IEEE-488 Cable, 2 meter length (6ft). Multiple quantity discount.
48 Agilent 10833C GPIB/IEEE-488 Cable, 4 meter length (13ft). Multiple quantity discount.
49 Agilent N2262A Multiplexer card for Agilent data acquisition systems. Connector block included
50 Agilent N2266A Multiplexer board for Agilent data acquisition systems. Connector block included
51 Agilent 82340A GPIB-16 bit board for PC.
52 Agilent 3497A Switch/Control Unit. GPIB,. Cards are availabled separately
53 Agilent 3499B Switch/Control Unit. GPIB, RS-232, 2 Card slots
54 Agilent 44476A RF switch card for the HP3488A, 3499A switch unit.
55 Agilent 54845B 1.5GHz, 8Gs/s, 4 channel, Color, USB, GPIB, CDROM, FDD..
56 Agilent 5062-7345 Rack mount kit for the Agilent & HP 54600 series oscilloscopes.
57 Agilent E2613A Wedge Probe Adapter for TQFP and PQFP, 3 Signal. New in a box.
58 Agilent E2614A Wedge Probe Adapter for TQFP and PQFP, 8 Signal. 0.5mm pitch. New in a box.
59 Agilent E2615A Wedge Probe Adapter for TQFP and PQFP, 3 Signal. New in a box.
60 Agilent E3642A 0-8V, 0-5A or 8-20V at 0-2.5A. NEW EQUIPMENT.
61 Agilent 66101A 0-8V, 0-16A, programmable plug-in for the Agilent 66000A mainframe
62 Agilent E3615A 0-20V, 0-3A. Digital displays...
63 Agilent 6632B 0-20V, 0-5A. Programmable power supply. 4.5 digit resolution. GPIB & RS232 interfaces. Free rack mount
64 Agilent 6544A 0-60V, 0-3.5A!
65 Agilent E3612A 0-120V, 500mA below 60V, 250mA above 60V. Constant voltage or current. 3.5 digit displays.
66 Agilent 6645A 0-120V, 0-1.5A. 3.5 digit setting accuracy. GPIB interface. Digital and analog front panel controls
67 Agilent G3170-80018 Bipolar HED power supply for the Agilent 5975 GC systems. Applied Kilovolts p/n HF007PZZ425
68 Agilent G1969-80108 Detector power supply for TOF III. Applied Kilovolts p/n HP010RZZ366
69 Agilent E3004-61030 Power supply for Agilent 94000 analog IC tester.
70 Agilent J2904A Internet Advisor ISDN module. New in a box with software and cables
71 American
Reliance
AR-180T
Transmission loss tester. Handheld tester with DMM function. Combines a 0dBm/-13dBm transmitter and AC
voltmeter with dB scale. Olso measures DCV, and Ohms
72 American
Reliance
AR-180T
Transmission loss tester with DMM function. Combines a 0dBm/-13dBm transmitter and AC voltmeter with
dB scale. Olso measures DCV, and Ohms
73 American
Reliance
AR-180T
Transmission loss tester. Handheld tester with DMM function. Combines a 0dBm/-13dBm transmitter and AC
voltmeter with dB scale. Olso measures DCV, and Ohms
74 Ameritec AM5 Transmission Impairment Measurement Set. Runs on AC or battery power .
75 Ameritec AM8A PCM/VF Call analyzer. Computer interface. Runs on AC or a built in rechargable battery
76 Amprobe A50-1 Current transformer. Extend the range of your clamp-on AC current probe to 1200A. With carrying case.
77 Amrel SPS20-60-002 0-20V, 0-60A. Digital displays, only 1.5" high, 19" rack ready. optional GPIB interface.
78 Amrel PPS-1322 0-30V, 0-2V programmable power supply. 1mV, 1mA meter resolution, GPIB interface. sold
79 Andy Gish ESD255 ESD Generator. 25kV, Event counter, Manual or variable repetition rate, External trigger input. Specs
80 Anritsu 41KA-6 Attenuator 6 dB, 2Wt, DC-18GHz, NEW! QIV

81 Anritsu 41KA-20 Attenuator 20dB, 2Wt, DC-18GHz, NEW!
82 B&K 1670A 0-30V, 0-3A, 5V @ 0.5A, 12V @ 0.5A Digital V & A readouts.. iii
83 B&K 1050 Universal telephone analyzer. Test telephones, faxes, modems, answ mach. etc.
84 B&K Precision 1660 2x 0-30V @ 2A ea. and 4-6.5V @ 5A. Tracking mode. Series/Parallel LED displays.
85 Bertan 105-03R 3kV, 333mA, Constant current or voltage mode. Reversable polarity, digital display, remote analog
86 Bertan 105-30R 30kV, 33mA, Constant current or voltage mode. digital display, high resolution V/I controls, remote analog
87 Biorad 200/2.0 0-200V, 0-2A. 200Wt max. CV or CC mode. Programmable On/Off time.
88 Bio-Rad 760 Switcher for Pulsed DNA electrophoresis. Switches up to760VDC at programmable time intervals from 0.1-
99,999sec.
89 Bird 43 RF Wattmeter. 100mW-10kW, 450kHz-2700MHz (element dependent). Free 50Wt, 2MHz-30MHz slug!
90 BK 1803B 100MHz handheld frequency counter. Rechargable or AA batt. and AC operation.
91 BK 1050 Universal telephone analyzer. Test telephones, faxes, modems, answ mach. etc.
92 BK Precision 3017A 2MHz Sweep/Function Generator with Main, TTL and CMOS outputs. 20V p-pk
93 BMI 4800 AC power analyzer and data recorder. Detect virtually any type of problem with AC power.
94 BMI A600 AC current probe. 600A contunuous current capacity. For BMI power analyazers.
95 Boonton 4400A RF Peak Power Analyzer. Repair service. Flat rate
96 Boonton 4400L RF Peak Power Analyzer. Repair service. Flat rate
97 Boonton 72BD Capaciance Meter, 1MHz test freq., Digital display, 0.01pF resolution. With a test fixture
98 California
Instruments
1001T
AC power source, 1000 Watt, 100-270VAC, 45Hz -5kHz , 8000T oscillator
99 Clarke-Hess 263 Watt, Power Factor meter. Plus ACA & VAC. Digital. Requires current transformer
100 Colby Instruments CPLD Programmable delay line 10pS to100pS. GPIB interface. Optional rack-mount kit included.
101 Cole-Parmer 1481-61 E-C E-C Meter & DIP cell probe. Six ranges, automatic temp compensation mode
102 Consultronics DLS200 Wireline simulator for DSL and ISDN with Impairment generator option. 10 standard test loops plus crosstalk,
impulse, powerline and longitudal noise impairments
103 Data Check 5010-ACP XYZ display. Substitute HP model.
104
Datapulse 201
Data-Pulse generator. Generate 16 bit serial data streams up to 10 MHz. Adjustable amplitude 0-10V and
offset: +/-10V. Manual or Auto trigger. Sync clock outputs. requires external drive signal sinewave ( 1Vrms) or
squarewave ( +/-0.5V).
105 DATRON 1082 7.5 digit DMM. AC/DC, Ohm, GPIB.
106
Dranetz 606-1
600 VAC max. Detects and measures Impulse, Sag/Surge, Slow Average. Clock with backup records time
of of the event. Automatically prints disturbance information. Built in printer.
107 Dranetz 626-PA-
6002
DC voltage monitoring module for Dranetz 626 power analyzer
108 Dranetz 626-PA-
6003
AC voltage monitoring module for Dranetz 626 power analyzer
109 Dranetz 626-PA-
6006
AC neutral line monitoring board for Dranetz 626 power analyzer
110 Dranetz 626-PA-
6030
AC Graphics monitor for Dranetz 626 analyzer
111 Dranetz 808 Power demand analyzer with built in printer. Accurate record of power consumption over time
112 Dwyer 470 Dwyer Thermal Anemometer. Low range:0.2-3 m/s, High range: 2-30 m/s. With probe.

113
Eaton 384M
1MHz - 4GHz., Synthesized signal generator , +18.5dBm max. power, Digital sweep, FSK/ FM/ AM/Phase
modulation. 1Hz max resolution. PC programmable. With optional Eaton 255 modulator. Other plug-ins avail.
114 EG&G 410 C-V plotter for silicone wafer analysis. Built in 1MHz capacitance meter
115 EG&G 5101 Lock-in amplifier. 5Hz-100kHz, 1uV-500mV.
116 EIP 545A 18GHz , -30dB sensitivity 12 digit resolution. Option 8 (GPIB). Up to 100 meas/sec..
117 EIP 548A 26.5GHz Microwave counter. Covers 10MHz to 26.5GHz frequency range..
118 EIP 548B 110GHz Microwave counter. Option 6 included. GPIB interface. . wj.
119 EIP 575 18GHz Source Locking Microwave counter with GPIB Interface. Opt 9 (rear input)..
120 Elgar 1001SL AC power source 2000VA, 0-260VAC, 45Hz to 5kHz variable frequency SD400 plug-in.
121 Elgar 1751SX-14 AC power source with 9012 variable frequency plug-in and GPIB interface
122 Elgar 9012 Variable frequency plug-in for Elgar 1751SX AC power source
123 ELGEN 1000 DC-2MHz, 170V p-pk output. 10mA max. High voltage pulse generator or high voltage sinewave.
124 EMI EMS7.5-75-1-D 0-7.5V, 0-75A, Constant current or voltage mode. Only 1.5" high. Digital high resolution displays.
125 EMI EMS10-60-1-D 0-10V, 0-60A, Constant current or voltage mode. Only 1.5" high. Digital high resolution displays.
126 EMI EMS40-125-2-D 0-40V, 0-125A, Constant current or voltage mode. Digital high resolution. Requires 3 phase AC.
127 EMS TCR7.5S300 0-7.5V, 0-300A, Constant current or voltage mode. FREE GPIB controller! For use on 190-250VAC lines
128 EMS ESS-40-25 0-40V, 0-25A, Constant voltage or current mode. LCD displays, 1.5" height. (add GPIB)
129 Fluke 1953A Universal Counter. 100MHz, dual channel. Options: 5,14,15,16. Rack mount kit available
130 FLUKE 77 III DMM. True RMS, Frequency, Capacitance, 10A current, Display with bargraph.
131 FLUKE 8000A 3.5 Digit Bench DMM. Measures voltages up to 1200V RMS
132 FLUKE 8050A 4.5 Digit Bench DMM dBm, Conductance, True RMS SOLD
133 FLUKE 8840A 5.5 digit, System DMM. DC voltage/current and Ohms only. option for AC and GPIB sold
134 FLUKE 8842A 5.5 digit, System DMM. AC-DC voltage/current (opt 09). GPIB interface (opt 05)..
135 FLUKE 8506A 6.5 digit, System DMM. with options 02A/09 (GPIB and Ohm's. No ACV
136 Fluke 80k-40 High voltage probe. Measure DC voltages up to 40kV with any digital multimiters
137 Fluke 90i-610S AC-DC current probe. 2 to 600A, 40Hz-400Hz. Works with any DMM or an oscilloscope. Retail price:
138 FLUKE 6011A 11MHz Synthesized Programmable Function Generator. GPIB interface.
139 Fluke 6160B Frequency Synthesizer 1-160MHz, Opt 002 (Hi stability time base), 13dBm max output.
140 Fluke PM5418TD Video Signal Generator PAL/SECAM/NTSC, 15 Sound formats, Baseband or RF out.
141 Fluke 105B Hand held oscilloscope/DMM. COMPLETE. 100MHz, 2 Chan., 2.5GS/s, RS-232.
142 Fluke VP190 200MHz, Oscilloscope probe with accesories. New with complete set of accesories. Sold as a pair.
143 Fluke PM2811 0-30V, 0-10A, 60Wt max., GPIB programmable..
144 Fluke 686 Network & Cable tester. Analyze data errors as well as wiring problems with Ethernet and Token ring
networks up to 100MHz
145 FW Bell 4048 Gauss Tesla Meter & probe. AC/DC fields, Peak hold, Auto/manual range. Handeld with LCD display.
146 FW Bell 640 Incremental Gauss Meter & probe. AC/DC fields from 1 to 3000 gauss. Differential probe avaliable
147 FW Bell 1776 Clamp-on AC, DC and AC on DC Current meter. 10, 100, 1000 A range. Peak hold. 5kHz BW, +/-1% DC or
AC Accuracy. With 10A probe
148 GGBoprobe 28 1 GHz oscilloscope probe. With power supply
149 GN Nettest 742S GN Nettest 7500 plug-in. Combines a source and power meter in one module 1310-1550nm
150 GN Nettest 7500 OTDR. Flexible configuration with optional plug-in modules.
151 GR 1265A 0 to 400V, 0 to 5A (200Wt max) Const. voltage or constant current mode. Line regulation 0.2%.
152 G-R 1390B Random noise generator, 3 ranges: 20kHz, 500kHz, 5MHz, 5V max output, 5 decades of attenuation. Pink

153 GW Instek GW-830 100MHz, 100MS/s, 50K Samples memory. RS-232, Printer port, Video output. X-Y mode, Voltage & Time
cursors.
154 GW Instek GDS-2204 200MHz, 4 channel 1GS/s, 25K Samples memory. USB, Color LCD, RS-232, X-Y mode. Full Specs
155 Hioki 2101 Megohm meter. Measure resistances up to 500 MOhm. 400V Test voltage. Remote control, Output terminals.
Pass/Fail test mode with alarm.
156 Hitachi VC-6155 100 MHz, Digital-Analog combination scope. Compact size, Frequency counter. 2mV sensitvity
157 Hitachi V-1560 100MHz, 2 Chan, 2mV sensitivity. One button autosetup. TV-sync trigger. 90 day warranty
158 HP 141T Spectrum Analyzer Mainframe. Storage mode 100% operational.
159 HP 3580A 5Hz-50kHz. 100nV to 20V amplitude, 80dB dynamic range. Opt 002 Rechargeable batt option
160 HP 3588A 10Hz-150MHz. Built in signal source. 0.25dB amplitude accuracy.
161 HP 8555A 10MHz-18GHz RF section Shown with optional display unit & IF section.
162 HP 8557A 10kHz-300MHz, 70dB attenuator, -60dBm sensitivity. Add HP 182 Large screen display oprion
163 HP 8562E 9kHz -13GHz. Available options: 001, 005, 007, 008. Memory module included
164 HP 8568B 100Hz-1.5GHz Synthesized accuracy delivers 10Hz resolution. Memory. RF SECTION only
165 HP 8569A 10kHz-22GHz, Signal storage, memory, GPIB output to printer or plotter. .
166 HP 8590A 10kHz -1.5GHz, Portable spectrum analyzer. 1 kHz resolution, opt 021 ( GPIB). New CRT .
167 HP 8591A 10kHz -1.8GHz, Portable spectrum analyzer. 1kHz resolution, 4 digit accuracy. .
168 HP 8595E 9kHz -6.5GHz Spectrum analyzer. 30Hz resolution. Available options: 021, 041, 140. .
169 HP 11729C Carrier-Noise test set. 10MHz-18GHz. Input signal: +7dBm to 20dBm.
170 HP 70904A RF Section for the HP 70000 series Spectrum analyzer. 100Hz-2.9GHz.
171 HP 339A Distortion Analyzer with built in Signal source. Signal range: 1mV-300V, 10Hz-110kHz.
172 HP 3580A Spectrum Analyzer. 5Hz-50kHz. 100nV to 20V amplitude, 80dB dynamic range. Opt 002
173 HP 8903A Audio signal analyzer. SINAD, amplitude measurements to 110kHz. Autoranging.
174 HP 1630D 100MHz Timing-25MHz State 43 channels. Glitch capture capability, 16 Timing channels and 27 state
channels. simultaneously.
175 HP 1631D 50MHz 200MS/s Scope & 100MHz & 43 Channel Logic analyzer. Flexible triggering. A001
176 HP 1650A 100MHz Timing-25MHz State 80 chan. . Menu driven user interface, Floppy
177 HP 1650B 100MHz Timing-35MHz State 80 chan. Menu driven user interface, floppy
178 HP 1651A 100MHz Timing-25MHz State 32 chan. ALL PROBES INCLUDED . Menu driven user interface, Floppy
179 HP 1651B 100MHz Timing-35MHz State 32 chan. . Menu driven user interface, Floppy
180 HP 1653B 100/35MHz Timing/State 32 channels with 100MHz DSO. Floppy drive storage ALL PROBES
181 HP 1661C 500/100MHz Timing/State 102 channels 8kb/chan memory. HP Mouse.
182 HP 1662AS 500MHz Timing-100MHz State 68 channels & 250MHz, 1Gs/s oscilloscope. 8kb/chan. Mouse, ..
183 HP 1660CS 500/100MHz Timing/State 136 chan. & 250MHz, 1Gs/s oscilloscope. 8kb/chan. Mouse,
184 HP 16500A Logic Analyzer mainframe. Color 9" CRT, floppy, 4MB memory lets you use 16550A/16555A
185 HP 16500A 100/35MHz Timing/State 80 chan. . Color Display, FDD, 4MB memory.
186 HP 16500A 500/100 MHz Timing/State 80 chan . . Color, floppy, Printer port, 4MB memory
187 HP 16500A Logic Analyzer-DSO .WITH PROBES Color, FDD, 4MB memory. Price is based on configuration. 6mo. warr.
188 HP 16500B Logic Analyzer 500MHz /110MHz Timing/State, 68 Chan. . 2MB memory.
189 HP 16500C Logic Analyzer 500MHz /110MHz Timing/State, 68 Chan. .2MB memory.
190 HP 16505A Prototype Analyzer. High level language debugging in windows environment for HP 16500C/D.
191 HP 16510A 100/35MHz Timing/State, 80 channels. For HP 16500A/B/C.
192 HP 16520A 100MHz 16 channel. . With optional 54650A GPIB interface

193 HP 16550A 500/100 MHz Timing/State, 102 chan. 4K/8K per channel. For 16500A/B/C.
194 HP 16555A 500/110 MHz Timing/State, 68 chan. 2MB memory.
195 HP 16555D 500/110MHz Timing/State, 68 chan. 2MB memory.
196 HP 54620A 16 channel logic analyzer. Automatic freq., period, hold & setup time. GPIB interface included.
197 HP 4195A Repair Service.
198 HP 8753A Network analyzer. 300kHz to 3GHz, opt 010 Time domain measurements. Bright CRT!
199 HP 8753B Network analyzer. 300kHz to 6GHz, opt 002, 006, 010. Excellent CRT display.
200 HP 8405A Vector voltmeter 1-1000MHz, 1uV-1V input, PLL capable. Sampling amp output adds 1GHz BW to any
oscilloscope
201 HP 8505A Vector network analyzer 500kHz-1300MHz. Measure Phase, Group Delay, Gain, Attenuation, Impedance,
Return Loss, S-Parameters, Reflection Coefficient, Deviation From Linear Phase and Transfer Function.
202 HP 8510B Network analyzer. Option 10. Eligible for Agilent trade in program for MXA & PXA analyzers.
203 HP 8755C Scalar Network analyzer. 3 channel, 10MHz-18.5GHz. With HP182T display.
204 HP 8757A Scalar Network analyzer. Opt 001, 4th Input channel. Color LCD display!.
205 HP 4145B Repair Service.
206 HP 4145A Semiconductor Parameter Analyzer. 4 SMU's and 2 VSU's, GPIB interface to LabView
207 HP 4145B Semiconductor Parameter Analyzer. 4 SMU's and 2 VSU's, GPIB interface to LabView
208 HP 4155A Semiconductor Parameter Analyzer. 4 SMU's and 2 VSU's, Color Graphics.
209 HP 4155B Semiconductor Parameter Analyzer. 4 SMU's and 2 VSU's, Color Graphics.
210 HP 4156B Semiconductor Parameter Analyzer. 4 HiRes SMU's and 2 VSU's, Color Graphics.
212 HP 4155B Repair Service.
213 HP 4155C Repair Service.
215 HP 4156C Repair Service.
217 HP 83480A Communication analyzer mainframe. Plug-ins are available separately..
218 HP 8750A Storage Normalizer unit. Adds digital storage to HP 8755, 8754A, 8505A, 8410/8412B.
219 HP 8901A Modulation analyzer. Measure AM/FM mod. with 1% accuracy. Also measures freq. & RF power 150kHz-
1.3GHz
220 HP 8901B Modulation analyzer. Measure AM/FM mod. with 1% accuracy. Measures freq. & power. 150kHz-1.3GHz. opt
001, 003
221 HP 8970A Noise figure meter. Provides accurate noise measurements up to 1500MHz.IN STOCK.
222 HP 41501A SMU-PGU expansion unit for HP 4155A, 4156A and other Semiconductor parameters analyzers
223 HP 5314A 100 MHz Universal Counter. Measure freq, period, ratio, time interval, totalize. 2 channels, 25mV sensitivity
Optional 001 High stability Time base ( <1 part in 10E7
224 HP 5315A 100MHz Universal Programmable Counter. 7 digit resolution. Measure freq., period, ratio, time interval,
totalize. 2 channels, 10mV sensitivity, x1 and x20 attenuator, adj. trigger level. Options available
225 HP 5315B 1.3GHz Universal Programmable Counter. 7 digit resolution. Period, ratio, time interval. opt 001
226 HP 5316A 1 GHz 3 channel Universal Programmable Counter. 8 digit resolution. Measure freq., period, ratio, time
227 HP 5316B Two channel Universal Programmable Counter. 8 digit resolution. Measure freq., period, ratio, time interval,
totalize. 10mV sensitivity, x1 and x20 attenuator, adj. trigger level..

228 HP 5316B 1 GHz 3 channel Universal Programmable Counter. 8 digit resolution. Measure freq., period, ratio, time
interval, totalize. 10mV sensitivity, x1 and x20 attenuator, adj. trigger level. Opt 001 & 003
229 HP 5334B Options 010 & 060. 9 Digits of resolution. Frequency, period, Rise/Fall time, Time interval, AC/DC voltage
230 HP 5335B 1.3 GHz 3 channel. Option 030 & 010 or opt 020 & 040. 9 Digits of resolution. Frequency, period, Rise/Fall
time, Time interval, AC/DC voltage, Pulse width, Math functions, GPIB.
231 HP 5335B Option 020 & 040. Frequency, period, Rise/Fall time, Time interval, AC/DC voltage, Pulse width, Math
functions, GPIB.
232 HP 5345A Universal Counter 500MHz, 25mV sensitivity, 9000 measurements per sec. Opt 011 (GPIB interface).
233 HP 5355A Converter plug-in for the HP5345A counter. Extends frequency range to 40GHz
234 HP 5370A Time interval counter. 100MHz max, pS resolution. -1.3 to 2V trigger range, GPIB
235 HP 3478A 5.5 digit resolution DMM. DCV, ACV, Ohms, AC/DC Curent. GPIB, Auto/Manual. SOLD
236 HP 4271B LCR meter. 1MHz test frequency, 3.5-digit display. Dissipation measurement. optional GPIB
237 HP 4275A LCR meter. 10MHz max test freq. DC Bias control (opt 001), GPIB (opt 017). 4 digit accuracy.
238 HP 4278A Capacitance meter. 1kHz/1MHz test frequency. opt 201 Handler interface.
239 HP 4140A Picoamp meter and Voltage source. Measure I, I-V and quasi-static C-V. Analog output (001), GPIB (101),
240 HP 400EL AC voltmeter. 10MHz, -60 to +30dBm.
241 HP 435B Power Meter. RF power measurements to 40GHz. Sensors & cable available separately.
242 HP 436A RF Power Meter with GPIB (opt. 022). 90 day warranty. Newest s/n. Eligible for Agilent trade-in program
towards EMP purchase.
243 HP 438A RF Power Meter. Dual channel, OPT 002 (rear connectors) RF power measurements to 40GHz. GPIB,
autorange.
244 HP 5004A Signature Analyzer Digital circuit troubleshooting tool lets you identify defective boards quickly without
technical help. With leads.
245 HP 5005B Signature Analyzer/Voltmeter/Frequency Counter/Ohm meter in one compact unit.
246 HP 5006A Signature Analyzer. Digital circuit troubleshooting tool lets you identify defective boards quickly without
technical help. GPIB interface (opt 040)
247 HP 8405A Vector voltmeter. 1-1000MHz range, 1uV-1V input, PLL capab.Also used as sampling amplifier.
248 HP 3324A 21MHz Synthesized Programmable Sweep/Function Generator.1mHz to 21MHz @ +/-5PPM.
249 HP 3325A 21 MHz Synthesized Programmable Sweep/Function , 1 mV to 10 V.. Option 001 available
250 HP 3325A 21 MHz Sweep/Function generator. Opt 001 (High stability). Output: 1 mV to 10 V into 50 Ohm load
251 HP 3325B 21MHz Synthesized Function generator. Programmable Sweep, uHz resolution, 1 mV-10 V..
252 HP 8116A 50MHz Pulse/Function generator. 3 digit resolution for frequency and voltage setting. Reliabity upgraded.
253 HP 8165A 50MHz Pulse Function Generator: 1.000 mHz to 50.00 MHz. Sine, Square, Triangle, Pulse, Ramp, Modes:
CW, VCO, trigger, gate, AM/FM modulation inputs and counted burst.
254
HP 8165A
50MHz Pulse Function Generator: 1.000 mHz to 50.00 MHz. Sine, Square, Triangle, Pulse, Ramp, Modes:
CW, VCO, trigger, gate, AM/FM modulation inputs and counted burst. Optional Sweep (opt 002), Rear
outputs opt 003.
255 HP 8904A Waveform synthesizer. Opt. 001, 002. FM and Stereo Modulation, 2nd output channel, DTMF sequences.
256 HP 4 Tone Gen. 800-900MHz, 0-30dBm output, 10kHz & 0.1dBm set point resolution, CW only.
257 HP 8350B Sweep oscillator mainframe. For HP 83000 and HP 86000 series plug-ins
258 HP 8656B Synthesized signal generator 0.1-990 MHz. -127dBm to +13dBm output. Opt.2
259 HP 8657A Synthesized signal generator 0.1-1047 MHz. From -127dBm to +13dBm output .
260 HP 8657B Synthesized signal generator 0.1-2060 MHz. From -127dBm to +13dBm output..

261 HP 8614A RF generator. 0.8-2.4GHz range. +10dBm (10mW) max power, 120dB attnuator, ext.AM/FM/Pulse
262 HP 8620C RF Sweep generator. Accepts plug-ins, that cover 10MHz to 22GHz range. 862XX plug-ins are listed below.
GPIB interface
263 HP 83525A Sweep oscillator plug-in. 10MHz-8.4GHz . Late serial number..
264 HP 83570A Sweep oscillator plug-in. 18GHz-26.5GHz. For HP 8350A/B sweep oscillator.
265 HP 86220A Sweep oscillator plug-in. Frequency range: 10MHz to 1.3GHz.. 13dBm max. output
266 HP 86222B Sweep oscillator plug-in. Frequency range: 10MHz to 2.4GHz.. 13dBm max. output
267 HP 86240C Sweep Oscillator Plug-in. 3.6 to 8.6 GHz., +20dBm For HP8620 & HP8350A/B with adapter
268 HP 86241A Sweep Oscillator Plug-in. 3.2 to 6.5 GHz, +8 dBm MAX level output, EXT. AM/FM mod.
269 HP 86242D Sweep Oscillator Plug-in. 5.9 to 9 GHz, 10 mV MAX LEVEL OUTPUT. For HP 8620
270 HP 86260A Sweep Oscillator Plug-in. 12.4 to 18.0 GHz, 10 mW MAX level output. Opt 001
271 HP 86290B 2-18 GHz Sweeper Plug-in . Sweep or CW mode. 10 dBm max leveled output; Power variation: +/-0.9 dB
internally leveled.
272 HP 86602A Sweep Oscillator Plug-in. 1 to 1300MHz. For HP 8660 Generator
273 HP 8007B 100MHz, max repetition rate. Rise/Fall time <2nS-250uS, DC offset, TTL, ECL, pos/neg output
274 HP 8011A 20MHz, Period: 50ns to 10s Pulse width: 25ns to 8 100ms. Pulse burst option 0-9999 pulse per cycle
275 HP 8012B 50MHz. Adjustable rise & fall time time (5nS min). adjuastable DC offset for TTL, ECL, CMOS .
276 HP 8013B 50MHz. Adjustable rise & fall time time (5nS min). adjustable DC offset for TTL, ECL, CMOS
277 HP 8015A 50MHz. Two outputs with independent amplitude control, adjustable transition times. 1-9999 pulses burst
278 HP 8018A 50MHz Serial Data/PRBS Generator, 2048 bit, dual channel memory, Variable word and pattern lenght, TTL,
ECL, CMOS compatible, Programmable, prbs and mixed data. HPIB interface.
279 HP 8082A 250MHz repetition rate, 2.3nS min pulse width, 1nS rise/fall time. 5V into 50Ohm. Two outputs.
280 HP 8112A 50MHz, adjustable transition times, burst mode, GPIB interface. Reliability upgraded
281 HP 8131A 500MHz Dual channel (opt 002), <200pS transition, 5V p-pk, Jitter < 0.025%. opt 001
282 HP 8175A Digital data generator. 32 TTL/CMOS channels. All pods and flying lead probes included. option 002/005
283 HP 204D Sinewave oscillator 0.1Hz-1.2MHz, low distortion 600Ohm output.
284 HP 651A Sinewave oscillator 10Hz-10MHz, low distortion. 60dB attenuator. Newer serial number
285 HP 59308A GPIB timing generator. Test GPIB interface timing accuracy.
286 HP 59309A GPIB addressable clock. Accepts external reference signal to produce accurate time clock
287 HP 16520A Data pattern generator. Cables included!. Probes are available separately. II STOCK.
288 HP 16521A Data pattern generator. Cables included! Probes are available separately..
289 HP 16522A Data pattern Vector generator for HP 16500 series analyzers. PROBES & PODS INCLUDED. option for
HP16500B
290 HP 8492A Attenuator with APC-7 connector. Available values: 3,6,10,20db
291 HP 11713A Step Attenuator Switch driver. With 2 attenuator control cables. GPIB interface
292 HP 8120-2703 Control cables for HP Step sttenuators. Brand New
293 HP 33320H Programmable step attenuator, DC-18 GHz, 11dB, SMA connectors. Get HP33321H option
294 HP 33321H Programmable step attenuator, DC-18 GHz, 70dB, SMA connectors. Get HP33320H option
295 HP 33322H Attenuator DC-18GHz, 110dB max, 10 dB step. FREE CONTROL CABLE
296 HP E1326A DMM card for the HP E1301A/B systems.
297 HP E1330B Multiplexer card for VXI systems with terminal blocks.
298 HP E1352A Multiplexer card for VXI systems; E1301B, E1302A
299 HP E1364A 16 Channel Form C switch. For VXI systems

300 HP 85A Computer with built in display and printer. With HP 82937A ( HPIB interface)
301 HP 3488A Switch/Control unit with GPIB interface. Up to 50 channels. DC to 26.5GHz. Cards are available separately
see list below
302 HP 37203A HPIB Range extender. Operate GPIB or IEEE-488 instruments at greater distances. Optional fiber optic
303 HP 44421A Data acquisition input multiplexer board (20 channel) with terminal block. vii
304 HP 44422A T/C interface card with terminal block for HP3497A data acquisition system
305 HP 44426A Conter module for the HP3497A data aquisition system
306 HP 44425A Digital output board with terminal block.
307 HP 44428A Actuator interface card with terminal block for HP3497 data acquisition system
308 HP 44431A High voltage actuator interface card with terminal block for HP3497 data acquisition system
309 HP 44470A Multiplexer card with connector block for HP 3488A switch unit. ii
310 HP 44471A Multiplexer card with connector block for HP 3488A switch unit. iv
311 HP 44472A Coaxial multiplexer card for the HP3488A switch unit.
312 HP 44473A Relay multiplexer card for the HP3488A switch unit. New in a box. iv
313 HP 44474A Digital I/O card for the HP3488A switch unit. vii
314 HP 44478B RF multiplexer switch card for the HP3488A switch unit. ii
315 HP 44703B Memory card for the HP3852A DAQ unit. 1MB total memory
316 HP 44705F Relay multiplexer card for the HP3852A and 3853A. Newer serial number
317 HP 44710A T/C interface card. 20 channels. for the HP3852A and 3853A. Newer serial number
318 HP 44711A High speed FET multiplexer for the HP3852A/3853A.. Connector block not included.
319 HP 44724A 16 channel digital output card for the HP3852A and 3853A.. Newer serial number
320 HP 44729A 20 Channel multiplexer card for the HP3852A, 3853A.. Newer serial number
321 HP 44788A HPIB controller for HP 3582A and HP 3583A
322 HP 59301A ASCII to Parallel converter. Permits control of many older HP instruments via GPIB interface
323 HP 59306A Relay actuator. Control six form-C relays by pushbuttons or via GPIB interface
324 HP 59307A VHF Switch. Dual Single pole 4 throw. GPIB or pushbutton. DC-500MHz, 50 Ohm
325 HP 59501A Power supply programmer. Control power supplies with analog programming capabilities with a PC via GPIB
interface. Isolated. Range +/-1V or +/-10V. 1mV/10mV resolution. LabView supported.
326 HP 59501B Power supply programmer. Control power supplies with analog programming capabilities with a PC via GPIB
interface. Isolated. Range +/-1V or +/-10V. 1mV/10mV resolution. LabView supported.
327 HP 1662AS 250 MHz, 1GS/s, 2 Chan oscilloscope with 500MHz 68Channel Logic analyzer. FDD, Mouse.
328 HP 16531A 100 MHz, 400MS/s, 2 Channel module. For use with HP16500 logic analyzer chassis
329 HP 16532A 250 MHz, 1GS/s, 2Chan. 8kB per channel. For use with HP16500B/C (available separately)
330 HP 54110D 1 GHz, 2 Ch, 40 MS/s, 10 bit vertical resolution, Color, Autosetup, IEEE-488 interface
331 HP 54111D 500 MHz, 2 CH., 2GS/s max, 8K points record, Color, Autosetup, GPIB. HP 54114A included.
332 HP 54120T Digital oscilloscope. 20GHz Bandwith, TDR, 4 channels HP54121A Test set with HP54120A
333 HP 54200A 50MHz, 2 Channel, GPIB interface
334 HP 54200A 50MHz, 2 Channel. GPIB interface.
335 HP 54501A 100MHz, 4 channel. Auto waveform & parameter measurements, GPIB interface.
336 HP 54504A 400MHz, 2 channel. Auto waveform & parameter measurements, GPIB
337 HP 54510A 250MHz, 1GS/s, 2 channels. Auto waveform & parameter measurements, Autosetup. GPIB
338 HP 54520A 500MHz, 1GS/s-500MS/s, 2 Channel, Floppy drive, Printer port. Large screen display.
339 HP 54603B 60MHz, 20MS/s, 2 Channel, DSO. 9" easy to read display. RS-232, GPIB, Paralle interfaces are available

340 HP 54602A 150MHz, 20MS/s, 4 Chan.DSO. 9" easy to read display. RS-232, GPIB, Parallel interfaces are available
341 HP 54602B 150MHz, 20MS/s, 2 Chan. DSO. 9" easy to read display. RS-232, GPIB, Parallel interfaces are available
342 HP 54721A 1GHz Vertical amplifier plug-in. For 54700 series oscilloscopes
343 HP 1340A XY display. Z axis input. High speed and high resolution display..
344 HP 37461A GPIB programmable display. 6" Hi-res CRT. .
345 HP 54701A 2.5GHz Active probe with complete set of accesories. Available w/o accesories option
346 HP 6281A 0-7.5V, 0-5A, Constant current or voltage mode. Add PC interface for option (GPIB)
347 HP 6282A 0-10V, 0-10A Const voltage or Current mode. Add PC interface for option (GPIB)
348 HP 6111A 0-20V, 0-1A. 5 decades of resolution permit setting output voltage with 1mV accuracy
349 HP 6286A 0-20 VDC, 0-10A, Voltage Regulation 0.01%. Add PC interface for option (GPIB). Simulate 120Wt solar
panel output for inverter testing
350 HP 6264B 0-20 VDC, 0-20A, Voltage Regulation 0.01%. Add PC interface for option (GPIB) Simulate 220Wt solar
panel output for inverter testing. (GPIB interface with HP59501A)
351 HP 6284A 0-20V, 0-3A Constant current or voltage mode. Add PC interface for option (GPIB)
352 HP 6552A 0-20V, 0-25A New surpus units. Free rack mount kit. Simulate 500Wt solar panel output for inverter testing.
Free GPIB interface
353 HP 6033A 0-20V, 0-30A. Autoranging, 240Wt max. GPIB interface.
354 HP 6261B 0-20V, 0-50A, Linear, Const. voltage or current. 115VAC (opt 26), 10 turn V/A pots (opt 9). GPIB interface
with HP59501A
355 HP 6215A 0-25V, 0-400 mA. Const voltage mode. 1mV ripple, size: 5.25x3.25x8" Fine V adj.
356 HP 6334B 0-36V, 0-10A, Constant current or voltage, Only 3" high. Volt and amp meter
357 HP 6104A 0-40V @1A or 2A from 0 to 20V. Precision power supply. Line regulation: 0.0005%+40uV, Load regulation:
0.0005%+100uV, Drift: 0.005%+50uV
358 HP 6200B 0-40 V, 0-0.75A, or 0-20V at 0-1.5A. Constant voltage or current. Regulation: 0.01%.
359 HP 6266B 0-40 V, 0-5A, Constant voltage or current. Regulation: 0.01%. Add PC interface for option (GPIB)
360 HP 6268B 0-40V, 0-30A, Constant voltage/constant current mode. Regulation 0.01%. opt 26 & 28 avail. (GPIB interface
with HP59501A)
361 HP 6012A 0-60V, 0-50A, 1000Wt. 90day warranty.
362 HP 6206B 0-60V @ 0.5A or 0-30 @ 1A dual range. 0.01% regulation, 200uV rms ripple
363 HP 6217B 0-60V, 0-250mA. Const voltage mod.. Very small; 5.25"x3.25"x8". Fine voltage adj. controls
364 HP 6218A 0-60V, 0-250mA. Const voltage or current modes. Very small; 5.25"x3.25"x8".
365 HP 6294A 0-60V, 0-1A Constant current or constant voltage mode. 0.01% regulation. Linear.
366 HP 6296A 0-60V, 0-3A Constant current or constant voltage mode. 0.01% regulation. Linear.
367 HP 6034L 0-60V, 0-10A, 200Watt max., Computer programmable (GPIB)
368 HP 6274B 0-60V, 0-15A, Const voltage or Current mode. Analog remote programming. Latest serial number
369 HP 6116A 0-100V, 0.2A Precision voltage setting with 0.1%+1mV accy, 200uV resolution.
370 HP 6115A 0-100V, 0.8A max Output voltage control with 4 digit accuracy.
371 HP 6035A 0-500V, 0-5A, 1000Wt, Constant voltage or current. GPIB interface.
372 HP 6621A Two outputs 0-20VDC@ 0-2A or 0-7V @ 0-10A, GPIB interface
373 HP 6227B 0-25V @ 0-2A. Dual output, CV/CC,Tracking mode. Low noise, single output winding produces continuous
voltage up to 50V!
374 HP 6234A 0-25V @ 0.2A dual or 0-50V single @ 0.2A. Small size: 3.64"x6.17"x8.25".
375 HP 6253A 0-20 @ 0-3A ea., 0.01% regulation, 200uV rms ripple. Constant voltage or current mode. Double output rating

376
HP 6255A
0-40 @ 0-1.5A ea. 0.01% regulation, 200uV rms ripple. Const. voltage or current modes. Double output
rating. Single output winding produces continuous voltage. NOTE: All inexpensive offshore P/S makers use
two transformer windings to achive 40V output, hence they cannot produce linear continuous output.
377 HP 6237B 0-18V @ 1A and two 0-20V outputs at 0.5A each. Tracking mode.
378 HP 4141B Programmable DC source/monitor for use in HP4062 semiconductor analysis systems
379 HP 6177B DC current source 0 to 500mA, 0-50V. 500uA resolution, 5mA, 50mA, 500mA range.
380 HP 6186B 0 to 100mA, 0-300V. 3 ranges; 1mA, 10mA, 100mA
381 HP J2301B Protocol analyzer opt 220, 220, 221. DS-3/E3 and Relay,ISDN,X.25,HDLC,SDL. RS232, RS449 & more.
382 HP 28687A Wiring Tester. Test any wiring harness for continuity and signal integrity (attenuation, crosstalk, burst). Tests
24 pairs simultaneously. Loopback adapters included.
383 HP 3779D Primary Multiplexer Analyzer for Bell/CCITT/Japanese networks
384 HP 37701B T1 Datcomm tester. ASYNC, SYNC, BERT. Ligthweight, Battery option available
385 HP E4200B Broadband Test System modules; PDH, Line Interface Modules, Cell processors
386 HP E4480A SONET Test Set. STS-1, STS-3, STS-3c, DS3..
387 HP E4480A SONET Test Set. opt: STS-1, DS3, DS1, DS0, Jitter for STS1,DS1,DS3.
388 HP E4480A SONET Test Set. opt: ST1, STS-3, STS-3C, DS0, DS1, DS3, V1.5, FT1, Jitter: STS1, DS3, DS1, DS3 Pulse
Mask.
389 HP E4480A SONET Test Set. opt: ST1, STS-3, STS-3C, STS-12, DS3, DS3 Pulse mask, V1.5, E1, DS0, DS1, TS, FM1,
ATM, GPIB
390 HP 156MTS SONET Test Set. STS-1, STS-3, STS-3c, DS3.
391 HP 156MTS SONET Test Set. opt: STS-1, DS3, DS1, DS0, Jitter for STS1,DS1,DS3.
392 HP 156MTS SONET Test Set. opt: ST1, STS-3, STS-3C, DS0, DS1, DS3, V1.5, FT1, Jitter: STS1, DS3, DS1, DS3 Pulse
Mask.
393 HP 156MTS SONET Test Set. opt: ST1, STS-3, STS-3C, STS-12, DS3, DS3 Pulse mask, V1.5, E1, DS0, DS1, TS, FM1,
ATM, GPIB
394 HP 3784A Digital communication analyzer. With Option 002.
395 HP 4934A Transmission Impairment and Noise Measurment test set available with opt 001 Rechargable batt or RS-232
interface
396 HP 4944A Transmission Impairment and Noise Measurment test set ( TIMS).
397 HP 4945A Transmission Impairment and Noise Measurment test set ( TIMS). 110kHz max freq.
398 HP 4951C Portable protocol analyzer 19.2 kbps max. Floppy disk to store setups and data. Supports HDLC, SDLC,
SNA, ISDN, CCITT X.25, Async/Sync/Bysync, IPARS, DDCMP.
399 HP 4952A Portable protocol analyzer 64 kbps max. Floppy Drive. Supports HDLC, SDLC, SNA, ISDN, CCITT X.25,
Async/Sync/Bysync, IPARS, DDCMP. Option 002 is available.
400 HP 18135A RS-232C Interface pod with Analyzer and DUT "Y" cable for HP4954A and other models
401 HP 18136A RS-449 Interface pod with Analyzer and DUT "Y" cable for HP4954A and other models
402 HP 18160A V-35 interface pod for HP 4951A/B/C, HP4952A and 4957A
403 HP 18173A RS-232C interface pod for HP 4951A/B/C, HP4952A and 4957A
404 HP 18179A RS-232C interface pod for HP 4951A/B/C, HP4952A and 4957A
405 HP 18180A RS-449 and RS232C interface pod for HP 4951A/B/C , HP4952A and HP4957A
406 Hughes 1077H11 TWT Amplifier 18 to 26.5 GHz, 1 Watt output. Full specs are available.
407 Hughes 8000H TWT Amplifier 3-5 GHz, 20 Watt output. Fulls specs are available upon request.
408 Hughes 8000H TWT Amplifier 10-15GHz, 40 Watt output. Fulls specs are available upon request.

409 IFR A7550 Portable spectrum analyzer. 10kHz-1GHz coverage, Tracking generator. 70dB dynamic range. Monitor any
type of FM/AM signals
410 IFR A-7550 Portable spectrum analyzer. 10kHz-1GHz coverage, Tracking generator. 70dB dynamic range. Monitor any
type of FM/AM signals
411 Impulse Semi TLP Transmission Line Pulse Test System. Accurately measure ESD parameters for wafers or packaged devices.
412 INCLUDED.
413 Instek GDM-8040 DMM, Benchtop, Frequency, Capacitance, Max/Min, Relative, Temperature, 20A AC/DC current
414 Instek GDS-2204 200MHz, 4 channel 1GS/s, 25K Samples memory. USB, Color LCD, RS-232, X-Y mode.
415 Interface
Technology
RS-690 250MHz digital word generator. 64 channels, up to 16kB of data per chan. Min pulse width 4nS. Options
included: Floppy disk, ECL pods, Variable current data pod (50Ohm)
416 ISCO 494 0-2000V, 0-200mA ( 100mA @ 2000V )Constant voltage, current or power mode Electrophoresis power
417 JFW 50DR-46-SMA Manual variable step attenuator. 50dB in 1dB steps. DC-2GHz, 2Wt, SMA connectors.
418 JVC TM-550U PAL/NTSC studio monitor. Three way power source 12VDC/120VAC or 12V batt. small size.
419 Kalmus 166AP Pulse amplifier. 400-450MHz, 300Wt output power. Linear gain.
420 Keithley 175 4.5 digit DMM V/A/Ohms, 4.5 digit resolution, dB, Relative, Logging, Auto/Man
421 Keithley 175 DMM with GPIB interface. V/A/Ohms, 4.5 digit resolution, dB, Relative, Logging, Auto/Man
422 Keithley 197 Microvolt meter dB, Relative, Logging, Auto/Man, GPIB
423 Keithley 175 DMM with GPIB interface. V/A/Ohms, 4.5 digit resolution, dB, Relative, Logging, Auto/Man
424 Keithley 610B Electrometer with proportional analog output. Input Resistance >10E14 Ohms
425 Keithley 1992 Scanner card for Keithley 199 DMM
426 Keithley 2000 DMM/Scanner 6.5 digit resolution, 2000 reading/s (4.5 digit), GPIB, RS-232
427 Keithley 619 Electrometer/DMM 5.5digit resolution, GPIB interface 6193 and 6194 input module. 10fA-2A, 10mOhm-
2TOhm, 1uV-200V. 2nd channel 6 module available option
428 Keithley AIM7 T/C Interface board for the Keithley 575 system
429 Keithley 706 Scanner/Switch unit. 10 slot for Keithley 7000 series control cards.
430 Keithley 7001 Scanner/Switch unit. 2 slot for Keithley 7000 series control cards.
431 Keithley 7011C Multiplexer card for the Keithley 7001, 7002 switch control unit. ii.
432 Keithley 7052 Relay matrix card 4x5 form factor. For Keithley 700, 7000 series mainframes
433 Keithley 7054 High voltage Relay matrix. For Keithley 705, 706 mainframes
434 Keithley 7055 Relay matrix card for Keithley 705, 706 mainframes
435 Keithley 7062 RF Relay switching card. For Keithley 705, 706 mainframes
436 Keithley 7071-4 Switching matrix card for Keithley 707. Dual 4x12 matrix with 5MHz BW.
437 Keithley 7072 Matrix card for 707 chassi.. Best Price
438 Kenwood PD35-20D 0-35V, 0-20A Digital displays, constant current or voltage modes. Linear design with extremely quiet output.
439 Kenwood PWR18-1T 2 of 0-18V @ 1A and 0-6V @ 5A. Tracking mode, 3 setup memory, output off control
440 Kepco BOP20-5D Power amplifier Bipolar power supply. +/-20V, +/-5A. Works as a power op amp to driver loads up to 210Wt.
441 Kepco BOP20-50MG Power amplifier Bipolar power supply. +/-20V, +/-50A.
442 Kepco BOP36-6M Power amplifier Bipolar power supply. +/-36V, +/-6A. Works as a power op amp to driver loads up to 210Wt.
443 Kepco ATE15-3 0-15V, 0-3A Constant current or voltage mode. Remote programming. Fast response Add GPIB interface for
option
444 Kepco JQE75-8M 0 to 75V, 0 to 8A, Constant voltage or current mode. High resolution V/I control.
445 Kepco ABC-200 0-200V, 0-150mA. 6.3VAC, Grid control output. CV or CC mode
446 Kepco HB4A 0-325V, in 5 ranges. 400mA. Constant voltage mode only.

447 Kepco BOP1000M 0 to +/-1000V, 40mA Bipolar DC Power supply and AC amplifier. Add GPIB interface with HP59501A
448 Kikusui PLZ300W Electronic load. 300Wt max. Static or Dynamic mode. Constant current or resistance.
449 Kikusui PAD8-5L 0-8V, 0-5A, Constant current or voltage mode. Small size. Linear design
450 Kikusui PAD35-5 0-35V, 0-5A Compact size, Remote control. Master/slave mode with tracking. add GPIB option
451 Kikusui PAB110-0.6 0-110V, 0-0.6A. CV or CC mode. LCD readouts. Analog programming. 00-0010
452 Kikusui PAD160-7L 0-160V, 0-7A. Constant duty power supply. CV or CC mode. Digital amp meter
453 Kikusui PAB250-0.25 0-250V, 0-250mA. CV or CC mode. LCD readout. Analog signal remote programming
454 Kikusui PAB350-0.1 0-350V, 0-1000mA. CV or CC mode. LCD readout. Analog signal remote programming
455 Lambda UP6-33 0-6VDC, 0-33A, Programmable power supply. RS-232/485 interface. Compact high efficiency design.
456
Lambda LT801-V1
5-12V, 0-100A Adjustable power supply. Const. Voltage or Current modes, Digital display, very compact and
light weight. Line voltage: 208-260 VAC
457 Lambda LLS4018 0-18V, 0-2A, Const current or voltage mode, digital controls & displays.
458 Lambda LLS6018 0-18V, 0-9A, Const current or voltage mode, digital controls & displays. Small size Simulate solar panel
459 Lambda LGSF24 24V, 41Amp, LED readout for V & A. Model # LGS-F-24-0V-R
460 Lambda LP-412A-FM 0-40V, 0-1A lab power supply, constant current or constant voltage mode, Separate meters for V and A. Low
noise and low ripple.
461 Lambda LP-522FM 0-40V, 0-2A lab power supply, constant current or constant voltage modes, Analog meters for V and A. Small
size. Low noise and low ripple. Cosmetically imperfect.
462 Lambda LP-532FM 0-40V, 0-3A lab power supply, constant current or constant voltage modes, analog meters for V and A. Low
noise and low ripple. Line regulation: 0.01%
463 Lambda LQ-532 0-40V, 0-5A. Digital display. Constant current or constant voltage mode. Remote control capability
464 Lambda LQ-523 0-60 V, 0-900 mA, digital V/A display, CV/CC mode, small size. Remote analog programming.
465 Lambda LQ-533 0-60V, 0-3.3A. Digital display. Constant current or constant voltage mode. 0.01% regulation.
466 Lambda LPT-7202FM 2 of 0-20V @ 1.5A each and 0-7V @ 5A. Separate volt and amp meters for each output.
467 Leader LMV-181A AC Millivoltmeter. 100uV-300V sensitivity, 5Hz-1MHz, dBV, dBM, V scales..
468 Leader LDM-170 Distortion/SINAD Meter with Voltmeter function. 1mV-300V input, 20Hz-20kHz. Filtering function
469 Leader LCG-399 PAL Video Signal Generator. Selectable audio modulation formats, Composite video, Full channel coverage..
470 Leader LCG-400 Video Signal Generator NTSC. Sound, Variable Sync option, Gen-Lock, Optional Multiburst module, TV
modulator
471 Leader LCG-409 Video Signal Generator NTSC. Composite & Channels 2 to 86, Sound, RGB, Battery/AC pwr.
472 Leader LBO-5860L TV waveform monitor. Dual channel, Line selection, field selection functions.
473 Leader LVS-5851A PAL/NTSC Vectroscope. Dual channel..
474 Leader LTC-905B Semiconductor curve tracer. Test BJT's, MOSFET's, UJT's, Diode's, SCR's on any oscilloscope!
475 Leader LPS-152 2 of 0-25V @ 1A and 0-6V @ 5A. Tracking mode. <3mV p-pk ripple
476 LeCroy 9211 Pulse generator plug-in. 250MHz repetition rate.. 300pS rise time, 5V into 50Ohm.
477 LeCroy 9214 Pulse generator plug-in. 300MHz repetition rate. 300pS rise time, 5V into 50Ohm.
478 LeCroy LW420 Programmable Arbitrary Waveform Gen. 100MHz, 400Ms/s, dual channel, 1MB memory
479 LeCroy 9310L 300MHz, 2CH, with 1MB points memory per channel option ("L"). GPIB, RS-232, PCMCIA, 9" display
480 LeCroy 9354AM 500MHz, 2CH, with 1MB points memory. GPIB, RS-232, PCMCIA, 9" display
481 LeCroy 9361C 300MHz, 2.5GS/s, 2 Chan, 25kSamples mem., 9" display, FDD, GPIB, RS232, Centronics ports.
482 LeCroy 9362C 1.5GHz, 10GS/s, 2 Channel, 9" display, FDD, GPIB, RS232, Centronics ports.
483 LeCroy PP006 500MHz, 10MOhm, General purpose oscillscope probe. Can be used with any scope. New!
484 LeCroy D300 4GHz Differential probe for use with Lecroy 9000 series oscilloscopes

485 LG OS-9020A 20MHz, 2 Channel, easy to use full featured oscilloscope.
486 LG OS-9020G 20MHz, 2 Channel with 1MHz Function generator. 10V p-pk output into 50Ohm, Sine, Triangular, Square
waves. DC offset
487 Link Instruments ADF25A High voltage differential probe. 20MHz, 1000V rms. Works with any oscilloscope.
488 Mini-Circuits TIA-1000-4 Power amplifier 100MHz-1GHz, 19dB gain, 4Wt linear, 12.5Wt saturated.
489 Mini-Circuits ZHL-32A-S Amplifier 0.05-130MHz, 25dB gain, +29dBm max. output, SMA, IP3: +38dBm Full specs
490 Mini-Circuits ZHL-2-8-S Amplifier 10-1000MHz, 31dB min. gain, +29dBm max. output, SMA, IP3: +38dBm. Full specs
491 Minolta TV-2130 Color and Luminance analyzer. Analyzer any color LCD or CRT for color purity and consistency.
494 Narda 4779-6 6dB Attenuator, DC-18GHz, SMA (m/f), 2Wt . QVI
495 Netcom X-1000 Fast Ethernet tester/simulator/analyzer for IEEE802.3.ture
496 Netcom JET-210 Jitter generator/standard for IEEE802.3 Ethernet standard
497 Netcom JET-211 Jitter generator/standard for IEEE802.3 Ethernet standard
498 Nettest 742S GN Nettest 7500 plug-in. Combines a source and power meter in one module 1310-1550nm
499 Nettest 7500 OTDR. Flexible configuration with optional plug-in modules.
500 Network
Communications
NP7100 Communication analyzer. T1, T1/2Mb, BERT, Digital TIMS, VOM, oscope, VT220 emulator, Tone generator..
Interfaces: RS232 V.24, RS-422, V35, T1, Telco, ISDN
501 NI BNC-2080 BNC interface board. p/n 181630
502 NI GPIB-TNT National Instruments GPIB board for a PC. 16 bit. For any PC with ISA slot
503 NI 182009-04 GPIB interface cable, standard to Single-End Male. p/n 182009-04 X5 Double-Shielded, 4 meter
504 NI 776857 GPIB interface with PCMCIA card. New in a box! National Instruments.
505 NI GPIB-PCMCIA GPIB interface with PCMCIA card. New in a box! National Instruments p/n 776857
506 NI SB-GPIB-TNT National Instruments GPIB board for SB bus
507 NI SCXI-1300 General-purpose terminal block with an onboard temperature sensor for cold-junction compensation.
508 NI SCXI-1102B 32 channel amplifier board. 200Hz BW. 333 kS/s maximum sampling rate
509 NI SCXI-1163R 32 channel opto-isolated solid state relay module
510 NI SB-GPIB-TNT National Instruments GPIB board for SB bus
511 NI VXI-MXI-2 National Instruments VXI CPU card.
512 NI 183105A-01 National Instruments VXI CPU card.
513 NI 182429H-20 National Instruments VXI CPU card.. VXIPC-486 model 566
514 NI 777145-01 National Instruments I/O connector block. New in a box!.
515 NI 763061-03 National Instruments 4.1m GPIB cable
518 NI 763061-4 National Instruments 8m GPIB cable
519 Noisecom NC9656 Programmable noise generator. 500MHz-9GHz, 0dBm max output, 80dB attenuator with 1 dB step resolution,
GPIB interface, Filter function.
520
NoiseCom
UFX/BER IBS/IDR Noise generator capable of Carrier-to-noise (C/N), Carrier-to-noise density (C/No), Bit energy-to-noise
density (Eb/No), Carrier-to-interferer (C/I), RF power and Precision noise generator. Optional Automatic
Gain control (Tracking)
521 NoiseKen FVC-777 EMI Analyzer. Measure spectral density of Electromagnetic fields from 100kHz to 1GHz.. Complete
system! datasheet

522 Philips PM5715 50MHz pulse generator. 10V output into 50 Ohm, adjustable transition times.
523 Philips PM5418TD Video Signal Generator PAL/SECAM/NTSC, 15 Sound formats, Baseband or RF out..
524 Philips PM2813 3 of 60V @ 5A each, 60Wt maximum. Programmable, with GPIB interface. PM2813/113
525 PM 1038-N10 Scalar Network Analyzer. Detectors and mainframe are available separately
526 PM 1038-D14M Scalar Network Analyzer chassi. Detectors and PM1038-N10 module are available separately
527 Polar 550 Milliohmmeter with short locator. Measure resistance down to 1 mOhm or locate short circuits on any PCB
board., Built-in current source. Ohmmeter 200 mOhm to 20 kOhm in 4 ranges.
528 Power Design TP325 2 of 0-32V @ 1A each and 0-6V @ 5A Tracking mode. This P/S will not cause IC lockup on power up. Specs
529 Power Design TP340 2 of 0-32V @ 1A each and 0-6V @ 5A or 0-15V @ 2.5A Tracking mode. This P/S will not cause IC lockup on
power up. Specs vii
530 Power Design TP343A 2 of 0-25V @ 2A each and 0-6V @ 5A or 0-15V @ 2.5A. Tracking mode. This P/S will not cause IC lockup
on power up. Specs xiv
531 Power Design TP343B 2 of 0-20V @ 2A each and 0-6V @ 5A or 0-15V @ 2.5A Tracking mode. This P/S will not cause IC lockup on
power up. Specs
532 Power Desing TW5005W Dual 0-50V, 0-0.5A output with tracking function. Single range with no output voltage jumps
533 Power Ten 4600D-20125 0-20V, 0-125A, LCD displays, Const current or voltage mode. Line requirements: 190-253VAC sinlge or 3
534 Power Ten 3300D-6010 0-60V, 0-10A, LCD displays, Height: 1.5" Const current or voltage mode.
535 Power Ten 4600D-15033 0-150V, 0-33A, LCD displays, Const current or voltage mode. Line requirements: 190-253VAC single or 3
536 Prism PPS 50S-1 0-50V, 0-1A, Programmable power supply. GPIB interface. High resolutions (4 digit)
537 Quantum Data 801GX Video generator. PAL/NTSC, VGA, MAC, SUN, S-Video, RGB. 100 built in patterns, 300 custom patterns.
GPIB, RS-232C.
538 Quantum Data 8701E 285 MHz analog video generator. Supports all forms of EIA composite sync. With. ACV 285 unit
539 R&S SMIQ02 2.2GHz Vector Signal Generator. -140 to +13dBm with 0.1dB step. SSB phase noise <-126 opt B19.
540 Rohde & Schwartz
CMT55
Radio Communication Analyzer with Optional GSM measurements mode. 0.1MHz-2000MHz, RF power,
Frequency, Modulation, Modulation amplitude, SINAD, Oscilloscope, Transmitter or Receiver test mode.ture
Options CMU-20, CMT-U26
541 Rohde Schwartz UPSF Video noise meter. 40 MHz BW, High resolution, filter functions..
542 Rohde Schwartz UPSF2E2 UPSF2 noise meter measurement module.
543 Schaffner NSG222 Interference generator. For use with Schaffner mainframe chassi only
544 Sencore SCR250 SCR tester for use with LC102 analyzer.
545 Sorensen XTS7-6M5 0-7V, 0-6A with Opt M5 analog programming interface. Const current or voltage mode, 3.5 digit digital
546 Sorensen XHR7.5-130 0-7.5V, 0-130A, with opt M9B (RS-232C), Constant current or voltage mode. High efficiency, small footprint.
547 Sorensen XTS15-4 0-15V, 0-4A Constant current or voltage mode. With opt GPIB-M
548 Sorensen HPD15-20S 0-15V, 0-20A Constant current or voltage mode. Digital display with analog bargraph.
549 Sorensen DCS20-150 0-20V, 0-150A, Constant current or voltage mode. High efficiency. Line requirements: Single or 3 phase 190-
240VAC. a001
550 Sorensen DCS33-33E 0-33V, 0-33A, opt M9; GPIB/RS232.. v
551 Sorensen DCS50-40M16 0-50V, 0-40A, 1 or 3 phase AC input, current monitor output.
552 Sorensen XTS60-1 0-60V, 0-1A Constant current or voltage mode. Digital display with analog bargraph
553 Sorensen QRD60-1.5 0-60V, 0-1.5A Constant current or voltage mode.
554 Sorensen XTS60-1 0-60V, 0-1A Dual output. Constant current or voltage mode. Digital display with analog bargraph.
555 Sorensen DCS60-18 0-60V, 0-18A, Const voltage or Current mode. Only 1.5" tall, rackmount standard.
556 Sorensen DHP100-50M9D 0-100V, 0-50A. option M9D (GPIB interface). Line requirements: 200-240VAC, 3 Phase

557 Sorensen DHP130-115 0-130V, 0-115A. Line requirements: 200-240VAC, 3 Phase
558 Sorensen DCS150-7E 0-150V, 7A, Constant current or voltage mode. High efficiency, rack mountable, only 1.5" in height. GPIB
interface is available
559 Sorensen DCR150-3B 0-150V, 0-3A, Constant current or voltage mode.
560 Sorensen DCR150-18B 0-150V, 0-18A, Constant current or voltage mode. Line voltage: 115VAC
561 Sorensen XT250-0.25 0-250V, 0-250mA. Constant voltage or current mode. 3 1/2 digit digital meters
562 Sorensen LT18-5 2 of 0-18V @ 5A each, 5V @ 3A. 18V outputs can be used in series to double the voltage to 36V, or in
parallel to get 10A.
563 Spectracom 8160a Standard Frequency receiver with 10 MHz output.
564 Spirent AX/4000 10GB Ethernet test system. Incl. 16slot chassi, 401427 control module, 403100 Generator/Analyzer, 403335
Test interface
565 Spirent 403100 10GB Ethernet test system. 403100 Generator/Analyzer, 403335 Test interface
566 Spirent 403335 10GB Ethernet test system. 403100 Generator/Analyzer, 403335 Test interface
567 Spirent DLS200 Wireline simulator for DSL and ISDN with Impairment generator option. 10 standard test loops plus crosstalk,
impulse, powerline and longitudal noise impairments
568 Spirent SMB-1000 Network tester mainframe. We have wide variety of plug-in cards for this tester
569 Spirent SMB-2000 Network tester mainframe. We have wide variety of plug-in cards for this tester
570 Spirent SMB1000 Network tester mainframe. We have wide variety of plug-in cards for this tester
571 Spirent SMB2000 Network tester mainframe. We have wide variety of plug-in cards for this tester
572 Spirent SE-6205 Interface card for Smartbits 1000 and 2000 systems. Quantity discount.
573 Spirent ST-6405 Interface card for Smartbits 1000 and 2000 systems. Quantity discount.
574 Spirent SX-7205 Interface card for Smartbits 1000 and 2000 systems. Quantity discount.
575 Spirent SX-7405 Interface card for Smartbits 1000 and 2000 systems. Quantity discount.
576 Spirent XPS/26-R24 Programmable Transmission Line simutaltor. Up to 15500 feet, GPIB interface. Rev. 6
577 SRS DG535 Repair service for your Stanford Research Systems DG535 Digital delay generator.
578 SRS DG535 Digital delay pulse generator. Opt 001.
579 SRS SR245 Computer Interface for NIM chassi.!
580 SRS SR250 Intergator Box Car Averager for the NIM chassi.! II
581 SRS SR280 Power supply and Display module for SRS NIM chassi.
582 Stanford Research DS335 3.1MHz Synthesized Sweep-Function generator. GPIB & RS232. 1uHz resolution, 10 Vpp into 50Ohm
583 Stanford Research DS345 30MHz Synthesized Function/Arbitrary/ /Sweep generator. GPIB (opt 001). 1 µHz to 30.2 MHz, 1 µHz
resolution. Sine, square, ramp, triangle and noise, AM/FM/Burst/Phase. Info
584 Sunrise Telco Sunset xDSL Portable Test Set. With opt. AD7: TDR/Line/DVM, AA0, SSXDSL-4: Alcatel ADSL ATU-C module
585 Systron Donner TL8-3 2 of 0-32 @ 1A each, 0-8V @ 3A. Separate meters for each output.
586 T-Com 324A T1 hand-held tester. Built in generator with BERT functions. Non intrusive DS1 monitoring and HDSL testing.
587 TEK TDS784D 1GHz, 4 Chan., 4GS/s. Options: 13,1F, HD, 2M, 2F
588
TEK 577/D2
Curve tracer 100Wt, 10A continuous, 20A peak pulse current power. Test any semiconductor device for V-I
characteristics. Also test batteries, lamps, relays. With 177 test fixture. Device adapters are available.
589 TEK 576 Tektronix 576 Curve tracer Flat Rate Repair Service.
590 TEK 5A14N 4 Channel Vertical amplifier plug-in for the Tektronix 5000 series oscilloscopes.
591 Tektronix TLA7M2 68Ch, 2GHz timing, 100MHz state analyzer module for TLA 700 series analyzers
592 Tektronix TLA704 Logic analyzer system. Boards are available separately.
593 Tektronix 1241C Test probes and ROM packs only

594 Tektronix VX4820 Digital Test Module for testing TTL systems. 64 channel. C-size, VXM bus module. ii
595 Tektronix VM700A Vidio signal analyzer Options 1, 11, 40.
596 Tektronix VM700T Vidio signal analyzer Options 1, 11.
597 Tektronix DAS9200SE Digital analysis system. Boards are available separately..
598 Tektronix RFM151 CATV signal analyzer. Complete signal measurements from 5MHz-1080MHz. RS-232 interface.
599 Tektronix TFS3031 OTDR. Single Mode Optical Time Domain Reflectometer. 1310 nm & 1550 nm single mode version. Unused,
with optional printer, FDD (opt 11), opt 8, Carrying case, New battery, Transit case
600 Tektronix DC504A 100Mz Universal Counter Timer. Measure Freq., Period, Time, Events & more. For TM chassis
601 TEKTRONIX DC509A 135 MHz, Dual channel Universal Counter/Timer. 8 digit Display, 5 ps max resolution, Auto trigger, Probe
compensation, A and B outputs, high stability Oven Time Base (opt 1). Works in TM 500/5000 chassis
602 Tektronix DC5010 350Mz Universal Counter Measure Freq., Period, Time, Events, GPIB interface. For TM500X
603 Tektronix DM502A DMM with RTD Thermometer option. Requires TM 500/5000 series chassi
604 Tektronix AWG2020 250MS/s arbitrary waveform generator. Digital outputs (opt 003), FFT editor (opt 009)
605 Tektronix AWG2040 500MHz arbitrary waveform generator opt 1,3,9. 4MB record length (opt 001), Digital outputs (opt 003),
FFT editor (opt 009)
606 Tektronix DG2020A Progrmmable Data generator. 200MHz data rate, 64k word memory. Simulates LCD and CCD signals
607 Tektronix DG2020A Progrmmable Data generator with TEK P3420 pod. 200MHz data rate, 64K word pattern memory
608 Tektronix PG501 50 MHz Pulse generator. <20nS to 200mS period, <10nS to 100mS pulse duration . +/-5V output into 50
ohms, Square wave mode, <3nS Rise time, Ext. trigger In/Out Dual adjustable complim. outputs.
609 Tektronix PG502 10Hz-250MHz Pulse generator, 1nS rise time, +/-5V output (5V p-pk max). Single pulse mode.
610 Tektronix PG505 High voltage pulse generator. 1MHz repetition rate. 80V pk-pk into 4kOhm, Variable Transition times.
611 Tektronix TG501 Time mark generator for calibrating any oscilloscope time base. Optional 5MHz time base.
612 TEKTRONIX SG502 Oscillator, 5Hz to 500kHz Sine and Square Waves, Low distortion Sine Wave, 5 V RMS, 600Ohm output
impedance, 70dB attenuator with 10dB steps.
613 Tektronix SG503 250 MHz leveled sinewave generator with Freq. counter. Requires TM 500 chassi. Newer s/n
614 Tektronix SG504 1024 MHz sinewave generator w/o output head. Requires TM 500 chassi.
615 Tektronix AGL1 Analog Generator Lock module for TG2000 mainframe.
616 Tektronix AVG1 Analog Multiformat generator module for Tektronix TG2000 mainframe.
617 Tektronix BG1 Black Generator module for Tektronix TG2000.
618 Tektronix DVG1 Digital Generator module for Tektronix TG2000.
619 Tektronix TSG130 Miltiformat video test signal generator with audio outputs. NTSC format.
620 Tektronix TSG131A Miltiformat video test generator with audio outputs.Option 003. PAL format.
621 Tektronix TSG170 Video test generator. 15 test patterns. Digital genlock. NTSC format.
622 Tektronix TSG 170 Video test generator. 15 test patterns. Digital genlock. NTSC format.
623 Tektronix TSG601 Video generator for serial digital format. Audio channels. Built in 50m coax cable simulator. Handheld size.
Soft case included
624 Tektronix 1410 Video test generator with SPG2, TSG7, TSP1, TSG3, TSG5, TSG6 .
625 Tektronix 1411 Video test generator with SPG12, TSG11, TSP11, TSG13, TSG15, TSG16.
626 Tektronix 1910 Video test generator/ Inserter. Studio, transmitter abd transmission test signals. 10-Bit signal generation. Opt
1 avail.
627 Tektronix VITS 100 Video test generator/ Inserter. NTC 7, FCC, and VIR Signals. FCC composite, multiburst
628 Tektronix VITS100 Video test generator/ Inserter. NTC 7, FCC, and VIR Signals. FCC composite, multiburst
629 Tektronix VITS 200 Generator/Inserter NTC7, FCC, VIRS, and GCR Signals Cable Multiburst and Sweep Signals.

630 Tektronix VITS200 Generator/Inserter NTC7, FCC, VIRS, and GCR Signals Cable Multiburst and Sweep Signals.
631 Tektronix DBI200 VBI Data Broadcasting Insertion System. All the features of VITS200 with addition of a computer interface.
New in a box
632 TEKTRONIX AM502 Differential amplifier with Hi/Lo pass filter.Gain from 1 to x100,000 in 5 decades. 1MHz BW, CMRR 100dB.
633 Tektronix SI5010 Programmable scanner for the TEK TM5000 series chassis. 16 channels. BNC connector
634 Tektronix 7D20 Digitaizer plug-in.Digital storage oscilloscope plug in for the TEK 7000 series oscilloscopes
635 Tektronix DSA602A Digital signal analyzer/DSO. 1GHz BW, 2Gs/s up to 12 input channels. Plug-ins available
636 Tektronix RTD710 Waveform digitizer. 200MS/s, 10 bit resolution. Works with any X-Y display.!
637 Tektronix RTD720 Waveform digitizer. 2GS/s, optional 1MB memory (opt 11).!
638 Tektronix TWD 120 Color Digital Storage oscilloscope on any PC. 100 Megasaples/sec. 8 bit vertical resolution. 5000 points
record per channel. Smaller than a laptop. Windows 3.1/95/98 software, Carrying case, Manual, SCSI card
and cable. t1, Pic2 Demo download
639 Tektronix 222 Handheld 10MHz, 2 Chan. Digital storage, 10Ms/s, Battery or 12VDC operation.
640 Tektronix TDS320 100MHz, 2 Chanel, 500MS/s, 2mV sensitivity. Measure 11 waveform parameters automatically.
641 Tektronix TDS340A 100MHz, 2 Chan., 500MS/s, 2mV sensitivity. GPIB, RS-232, VGA, Floppy Drive and Printer port.
642 Tektronix TDS350 200MHz, 2 Channel, 1GS/s, 2mV sensitivity. Measure 11 waveform parameters automatically.
643 Tektronix TDS360 200MHz, 2 Channel, 1GS/s, 2mV sensitivity. Measure 11 waveform parameters. Floppy drive
644 Tektronix TDS 360 200MHz, 2 Chan., 1GS/s, 2mV sensitivity. Measure 11 waveform parameters Floppy drive
645 Tektronix TDS460 350MHz, 4 Channel, Options: 1F (floppy drive). Rackmount kit available..
646 Tektronix TDS460A 400MHz, 4 Channel, Options: 1F (floppy drive). Rackmount kit available..
647 Tektronix TDS460A 400MHz, 4 Channel, Options: 1M, 05, 2F, 13. Rackmount kit available ..
648 Tektronix TDS460A 400MHz, 4 Channel, Options: 1M, 05, 2F, 13. Optional portable printer (opt. TDS4F5P)
649 Tektronix TDS460AXL 400MHz, 4 Chan., Options: 1M (120K memory), 05 (Video), 2F (FFT & Waveform Math), 13 (GPIB, RS-232,
Centronics). Rackmount kit available
650 Tektronix TDS 460AXL 400MHz, 4 Chan., Options: 1M (120K memory), 05 (Video), 2F (FFT & Waveform Math), 13 (GPIB, RS-232,
Centronics). Rackmount kit available
651 Tektronix TDS520C 500MHz, 1GS/s, FFT (opt 2F), HD (160MB hard drive), FDD (opt 1F)
652 Tektronix TDS520 REPAIR SERVICE
653 Tektronix TDS524A REPAIR SERVICE
654 Tektronix TDS540 500MHz, 1GS/s, 4 channel. Flexible triggering, 50K points record per channel (opt 1M), Opt 2F (FFT), opt 13
(RS-232, Parallel Inteface)
659 Tektronix TDS520D REPAIR SERVICE
662 Tektronix TDS540C REPAIR SERVICE

670 Tektronix TDS754C REPAIR SERVICE
673 Tektronix TLS216 REPAIR SERVICE
675 Tektronix TDS210 60MHz, 2 Channel, 1GS/s, LCD display, automatic waveform measurements, math functions, X-Y mode
676 Tektronix TDS784D 1GHz, 4 Chan., 4GS/s. Options: 05,13,1F, HD, 2F, 2C
677 Tektronix 2201 20MHz, 10MS/s, 2Ch, Digital storage and Analog scope in one instrument. 2mV to 5V per/div
678 Tektronix 2220 60MHz, 20MS/s, 2Ch, digital storage and analog scope in one instrument. 2mV to 5V per/div sensitivity.
679 Tektronix 2221 60MHz, 100MS/s, 2Ch, digital storage and analog scope in one instrument. 2mV to 5V per/div sensitivity.
Optional GPIB port
680 Tektronix 11403A Oscilloscope mainframe. 3GHz Bandwith. Option 1S. Plug-ins are available separetely
681 Tektronix TAS465 100MHz, 2 Channel, Automatic measurment of waveform parameters. 90 day warranty
682 Tektronix TAS475 100MHz, 4 Chan, Automatic measurment of waveform parameters. 90 day warr.
683 TEKTRONIX 2213 60MHz portable oscilloscope. 2mV sensitivity,. Lightweight: 13 lb. 6month warr.
684 TEKTRONIX 2225 50 MHz, 2 Channel, 2mV max sensitivity, Dual time base.Weights only 13lb.
685 Tektronix AN/USM-488 100MHz , 2Ch,. 2mV sensitivity, dual time base. TV triggering.. only 13lb, 6month warr.
686 TEKTRONIX 2235 100MHz , 2Chanel,. 2mV sensitivity, dual time base. TV triggering.. only 13lb, 6month warr.
687 TEKTRONIX 2235A 100MHz , 2Channel,. 2mV sensitivity, dual time base. TV triggering.. only 13lb, 6month warr.
688 TEKTRONIX 2236 100MHz oscilloscope with Frequency Counter and 4.5 digit Digital multimeter. 6 month warranty
689 TEKTRONIX 2245A 100MHz , 4Ch. 2mV sensitivity, dual time base. Cursor measurements. Automatic setup
690
TEKTRONIX 2247A
100MHz , 4Ch. 2mV sensitivity, dual time base. Autosetp and automatically measurement of waveform
parameters.
691 Tektronix 2445 150MHz, 4 channel. Dual time base. Portable, weight 22.4 lb. 90 day warranty
692
TEKTRONIX 2445B
200MHz, 4 ch. with cursor measurements of V & time. Dual time base. Portable, weight 22.4 lb. 90 day warr.
two 200MHz probes, GPIB and other options are available
693 TEKTRONIX 2465 300MHz, 4 channel. two 300MHz probes, 45 day warranty. Option 11 (active probe power supply)
694 TEKTRONIX 2465CTS 300MHz 4 channel with Counter-Timer and GPIB IEEE-488 interface. 6 month warr.
695 Tektronix 2465A 350MHz 4 channel analog oscilloscope. Autosetup, on screen waveform parameter measurements.
696 Tektronix 2465ADV 350MHz 4 channel analog oscilloscope with DMM option
697 Tektronix 2465B REPAIR & CALIBRATION. ANY PROBLEM. Includes NIST traceable calibration
698
Tektronix 2465B
400MHz 4 ch 500pS rise time. Auto setup feature, on-screen measurements of 12 waveform parameters. 90
day warranty, Different options are available
699
Tektronix 2465BDM
400MHz 4 ch 500pS rise time. Auto setup feature, on-screen measurements of 12 waveform parameters.
optional built in 4.5 digit DMM, Frequency Counter, GPIB interface.
700 Tektronix 2467B 400MHz 4 channel. Autosetup & Automatic waveform measurements. GPIB interface.
701 Tektronix 5103N 2MHz analog storage oscilloscope.
702 Tektronix 5111 2MHz analog storage oscilloscope.
703 Tektronix 5115 2MHz analog storage oscilloscope. Up to 8 traces simultaneously with 5A14 plug-ins.
704 Tektronix 5440 50 MHz analog oscilloscope. Up to 4 analog channels. Rack mount version is available

705 TEKTRONIX 7603 100MHz Modular oscilloscope. Up to 4 input channels.
706 Tektronix 7623A 100MHz, Analog storage oscilloscope. Choose from many types of plug-ins.
707 Tektronix 7633 100MHz, Analog storage oscilloscope. Choose from many types of plug-ins. SOLD
708 Tektronix 7834 400MHz, Analog storage oscilloscope. 4 input channels.
709 Tektronix 7104 1GHz Oscilloscope, the fastest, real-time oscilloscope ever made. Ultra-high writing speed of 20 cm/us. 350
ps rise time. Complete dual channel dual time base system
710 Tektronix C-5C Oscilloscope camera. Capture single shot events with analog Tektronix oscilloscopes.
711 Tektronix WFM300 TV Waveform Monitor. Betacam mode (opt. 10)..
712 Tektronix WFM601E Video Waveform Monitor for 270MB serial component operating enviroment.
713
Tektronix 5CT1N
Semiconductor curve tracer. Up to 0.5W. 10nA/div to 20mA/div, 0.5V/div to 20V/div horisontal factors. FET or
Bipolar devices.
714 Tektronix 528A Waveform Monitor for NTSC
715
Tektronix 577/D1
Curve tracer 100Wt, 10A continuous, 20A peak pulse current power. Storage Mode. Test any semiconductor
device for V-I characteristics. Also test batteries, lamps, relays. With 177 test fixture. Device adapters are
available.
716 Tektronix 576 Semicunductor Curve tracer. 220Wt, 1500V. Device adapters are available.
717 Tektronix 067-0405-02 Calibration fixture for TEK TDS7000 series oscilloscopes
718 Tektronix 1420 NTSC Vectroscope with two separate input channels. Phase adjustment. Open frame chassi
719 Tektronix 1485R NTSC/PAL Waveform Monitor. User selectable display for line, field and sync. two inputs, variable vertical
720 Tektronix 1503B Metallic cable TDR. Find faults in coaxial cables up to 50,000ft. long.
721 Tektronix 1503C Metallic cable TDR. Find faults in coaxial cables up to 50,000ft. long. Option 04 (YT-1 Printer)
722 Tektronix 1710B Waveform Monitor for NTSC systems..
723 Tektronix 1720 Waveform Monitor/Vectroscope. NTSC..
724 Tektronix 1725 NTSC/PAL Waveform Monitor/Vectroscope..
725 Tektronix 1730 Waveform Monitor. Dual channel, Microprocessor control. Front panel setup memory.
726 Tektronix 1730D Waveform Monitor. Dual channel. Computer interface..
727 Tektronix 1735 Waveform Monitor. Dual system; NTSC/PAL. .
728 Tektronix 1740 Waveform Monitor/Vectroscope and Phase display. NTSC.
729 Tektronix 1750 Waveform Monitor/Vectroscope and Phase display. NTSC.
730 Tektronix 1751 Waveform Monitor/Vectroscope and Phase display. PAL system
731 Tektronix 1780R Video measuring system; Waveform Monitor & Vectroscope. NTSC.
732 Tektronix 5A22 Differential amplifier plug-in for the TEK 5000 series oscilloscopes. Hi pass-Low pass filter
733 Tektronix 5S14N 1 GHz Time equivalent sampler for 5000 series. Rise time <350pS, Dual ch., 2V p-p max
734 Tektronix 7A13 Differential comparator for Tektronix 7000 series oscilloscopes..
735 Tektronix 7A24 350 MHz dual channel vertical amplifier for 7000 series oscilloscopes. 5mV to 5V per/div.
736 Tektronix 7S11 Sampling unit which accept diffirent types of sampling heads. t
737 Tektronix K212 Oscilloscope cart. Fits TEK 2400, TDS series and many other types of equipment.
738 Tektronix K218 Equipment cart. 3 shelfs.
739 Tektronix 11A34 Vertical amp pluig-in for 11XXX and DSA series oscilloscopes. 4 channel
740 Tektronix 11A71 Vertical amp pluig-in for 11XXX and DSA series oscilloscopes.
741 Tektronix AM503A Current probe amplifier with TM502A chassi. For TEK A6302, A6303 probes.
742 Tektronix A622 Current probe AC/DC, 100kHz BW, 50mA-50A max. For DMM's and oscilloscopes
743 Tektronix P2200 200MHz x1/x10 passive probe for any oscilloscope. New with complete set of accesories

744 Tektronix P2220 200MHz x1/x10 passive probe for any oscilloscope. New with complete set of accesories
745 Tektronix P5100 High voltage oscilloscope probe x100 with complete set of accesories
746 Tektronix P5200 High voltage differential probe. 25MHz, 1300V, 10MOhm, 4.7pF input. x50/x500 attenuation. With power
supply and clips
747 Tektronix P6109 150 MHz probe, Rugged modular construction. 11.8pF. For any oscilloscope. With accessories
748 Tektronix P6015 HV probe. 40kV max. measurment. Works with any oscilloscope. Probe will be charged with dialectric fluid
before shipment.
749 Tektronix P6046 Differential probe. 100MHz BW, CMRR: 10,000 @ 50kHz.. COMPLETE set of hard to find accesories. a001
750 Tektronix P6130 250 MHz probe, 10.8pF, x10, 1.5m long. For any oscilloscope
751 Tektronix P6133 150 MHz probe, 11.4pF, x10, 1.3 or 2.0m long. For any oscilloscope
752 Tektronix P6138 400 MHz general purpose oscilloscope probe for 1MOhm oscilloscope inputs, x10. With standard accesories
753 Tektronix P6139 500 MHz general purpose oscilloscope probe for 1MOhm oscilloscope inputs, x10. With standard accesories
754 Tektronix P6562 SMT oscilloscope probe. 350MHz BW, x10 attenuation. With accesories and storage case
755 Tektronix P6202A 500MHz FET probe for 50 Ohm or 1 MOhm systems. 2pF input capacitance. Dynamic range +/-6.0V ( 60V
with external attenuator). 10x attenuation. DC Offset nulling.
756 Tektronix P6106A 250MHz, x10 oscilloscope probe. With ground lead and Spring Hook tip. Lenght: 2m
757 Tektronix P6230 1GHz active probe for use with any oscilloscope. Tektronix probe pwr jacks. TEK1101A P/S required if no
jacks available
758 Tektronix P6467 High speed probe adapter for the TLA520 series logic analyzers
759 Tektronix S-3A Sampling head DC- 1GHz with probe. Rin= 100kOhm, <2.3pF. Complete set of accesories.
760 Tektronix S-4 Sampling head DC-14GHz for Tektronix 7S11 or 7S12 plug-ins
761 Tektronix S-6 Sampling head DC-11.5GHz for 7S11 or 7S12 plug-ins. ii
762 Tektronix SD-26 Sampling head DC-26.5GHz.
763 Tektronix S-52 Pulse generator head 25pS rise time for Tektronix 7S11 or 7S12 TDR ii
764 Tektronix TD100 Data managment computer for the Tektronix TDS series oscilloscope family. Adds hard drive storage thru an
oscilloscope GPIB interface.
765 Tektronix 067-0484-01 Deskew fixture for the TEK P6246, P6247, P6248 probes.
766 Tektronix 015-0310-01 Comparator Head for use with Tektronix calibration plug-ins
767 Tektronix 016-1166-00 Rack mount kit for the Tektronix TDS 300 & TDS 400 series oscilloscopes
768 Tektronix PS2510G 0-36V, 0-3.5A, GPIB programmable..
769 Tektronix PS501-1 Precision power supply. 0-20 V with 10mV resolution setting 0-400mA, 5VDC @ 1A fixed output. For TEK TM
series chassies
770 Tektronix PS503A 2 of 0-20V @ 0-1A max and 5V @ 1A. Tracking mode. For TEK TM500/5000 chassis only
771 Tektronix PS280 2 of 0-30V @ 0-2A max and 5V @ 3A. Tracking, Parallel, Series modes on 30V outputs..
772 Tektronix GB1400 GigaBert Tester and Generator. Computer interface. Internal or external clock mode
773 Telebyte 453 Transmission line simulator. From 500 to 18500 feet. Remote control capability
774 Teltone TLS-4 Telephone line simulator. 4 simulated phone lines with 2 simultaneous independent conversations. Add your
own audio signal. Test dialing, ringing, ringback, busy tone response and much more.
775 Teltone TLS-4A-01 Telephone line simulator. 4 simulated phone lines with 2 simultaneous independent conversations. Add your
own audio signal. Test dialing, ringing, ringback, busy tone response and much more.
776 Tenma 72-7210 5MHz Sweep-Function generator with frequency counter. 1:1000 Sweep control (10mS-5sec), Pulse function,
20dB attenuator, DC offset. Measure frequency up to 50MHz with internal counter.

777 Topward TFG 4613 12 MHz function generator, Sine, Square, Triangular, Pulse. AM/FM/Sweep functions, dual output, Variable
symmetry. Clone of the HP 3312A
778 Topward TPS-3000 Dual 0-30V, 0-2A output with tracking function. Four separate meters for simultaneous monitoring of voltage
and current
779 Topward TPS-4000 2 of 0-30V @ 6A each. Four analog meters for simultaneous monitoring of voltage & current, Tracking mode,
ture
780 Topward 6303A 2 of 0-30V @ 6A ea., 5V @ 5A. Four analog meters, Tracking mode, CV or CC mode.
781 Topward 6306D 2 of 0-30V @ 6A ea., 5V @ 5A. Digital meters, Tracking mode, CV or CC mode.
782 Transistor Devices DLP50-60- 1000A 1000Wt, 60A, Static or dynamic mode. Three current ranges: 6, 18, 60A.
783 Transistor Devices DLP50-20-100 Electronic load with LCD displays. Hi/Lo range, Constant current or constant voltage mode. Available in a
rack of 4 units
784 TTC PR-40A Portable Thermal printer. For use with TTC analyzers
785
TTC 224
Protocol analyzer with options 11704 ENH ESF/SLC, 41500 T1/FT1/DDS BERT, 12041 G.821 PERF, 12042
ADV STRESS PAT, 13963 SMRT Loopback, 42659 DSP opt BD, 12708 Digital Analysis, 12709
SS7/ISDN mon, 13964 Caller ID, 14875 VF, 41934 Signalling
786 TTC 310 Protocol analyzer with DS1/DS3 interface; opt 1 and 3
787 TTC 2000 Bit Error Analyzer. Up to 64 kBaud. With RS-232 interface.
788 TTC 4000 Communication analyzer. Two interface slots allow mixing of different test modules in one analyzer.
789 TTC 6000A Communication analyzer. Inteface modules are available separately
790 TTC 6005 GPIB Inteface module for TTC6000A analyzer
791 TTC 40200 RS-449 interface for the TTC 4000, 6000 analyzers iii
792 TTC 40202 V.35 Interface module for TTC 4000, 6000 analyzers
793 TTC 40204 Interface module for TTC 4000, 6000 analyzers
794 TTC 40849 T1 channel monitor and lid for the TTC209.
795 TTC 41440 T1/FT1 interface for the TTC6000 analyzer. Unused condition
796 TTC 41440A T1/FT1 interface for the TTC6000A analyzer.
797 TTC 41704-01 V35 inteface plug-in for TTC 6000
798 Valhalla 2101 W-A-V meter. Wide band AC or DC up to 300V, 20A. Low range 200mA.
799 VEB RFT PSI 202 Sound level meter. Impulse, Fast, Slow response. 17 to 140dB, 20Hz to 40kHz. Vibration analisys
(accelerometer required). Filter port allow band measurements.
800 Velonex 510 Surge Transient generator. Connects directly to AC mains and generates up to 2.5kV transients.
801 Wavetek 8501 RF Peak Power meter. Works with Gigatronics power sensors.. wj
802 Wavetek 8531 RF Power meter. Measure power up to 26GHz. GPIB, Analog and digital display. W/o sensor
803 Wavetek 22 11 MHz Frequency stabilized Sweep/Function Generator. Frequency accuracy is 0.09% over its 100 Hz to 11
MHz. LCD display, Lin/LOg sweep, 20V p-p, 6 functions, small size
804 Wavetek 131 2MHz Function Gen. with Freq. control by ext.voltage, 50/600Ohm output, -60dB to +10dB
805 Wavetek 180 2MHz Function Gen. with Sweep control. Standard waveforms plus var. symmentry
806 Wavetek 186 Phase lock generator. 0.0001Hz to 5MHz, phase lock to external frequency. Rack mount case.
807 Wavetek 275 Function-Arbitrary waveform generator. 10mHz-12MHz, Record length 8192 points (opt 4)
808 Wavetek 288 20MHz Synthesized Function Generator, 30V p-p output, FM/AM/Sweep/Phase Angle.
809
Wavetek 955
Signal source 7.5-12.4 GHz, +10dBm, +/-0.1dB flatness, 25dB control range, Long term stability: 0.009%,
Harmnonics: <-20dBc, Spurios noise: -55dBc. internal AM/FM modulation, Sweep or CW. External power
leveling and Phase lock

810 Wavetek 1084 3500-4500 MHz Sweep/CW generator with digital readouts.+13dBm to -60dBm..
811 Wavetek 680-3 100 MHz Pulse Generator Modules. Add channels to your Wavetek 869 modular pulse gen.
812 Wavetek 802 50MHz Pulse Generator. 5nS Rise/Fall time. Rack mout case option.
813 Wavetek EH2000 200MHz max repetition rate. 1nS rise time, 5V p-pk into 50Ohms. Fully programmable
814 Wavetek 1391 50MHz Pulse generator. VXI chassi.. BEST PRICE
815 Wayne Kerr 3245 Impedance Analyzer. Can test transformers and large value inductors. Option BCI-A installed
816 Weinschel 3T-10 10dB Attenuator. DC-12.4GHz, SMA (f/m). NEW! QIII
817 Weinschel 3T-20 20dB Attenuator. DC-12.4GHz, SMA (f/m). NEW! QII
818 Weinschel 33-20-12 3dB, 50Wt Attenuator. DC to 8.5GHz, 3.5mm connectors.
819 Weinschel 33-3-12 20dB, 50Wt Attenuator. DC to 8.5GHz, 3.5mm connectors.
820 Weinschel 5872 DC-20GHz, 0-90dB step attenuator, 24V.
821 Weinschel 152A-70-1 DC-26.5GHz, 70dB step attenuator, 24V.
822 Weinschel 167-110 DC-18GHz, 110dB step attenuator, 24V.
823 WG ANT-20 Advanced netwok tester. Contact for list of options
824 WG ANT-20SE With STM-64 and OC-192 Inteface module. Contact us for the list of installed options.
825 WG ANT20SE With STM-64 and OC-192 Inteface module. Contact us for the list of installed options.
826 WG 2262/90.1 Acterna E1/T1 Module for the Acterna 8630 analyzer
827 WG PKN-1 Transmission Line simutaltor. 10kHz to 10MHz, 75Ohm impedance. BNC connectors
828 WG PA-20 Portable PCM channel analyzer. Complete with accesories and carring case.
829 WG BN9305/00.17 Wan Analyzer module for DA-30 analyzer
830 WG BN7511/00.18 ISDN BRA Line interface for DA-30 analyzer
831 Wiltron 560 Scalar network analyzer, 10MHz to 40GHz. Three input channels. Detectors available
832 Wiltron 562 Scalar network analyzer, 10MHz to 40GHz. Four channels. Detectors are available.
833 Xantrex XFR7.5-140 0-7.5V, 0-140A. Only 1.5" tall.
834 Xantrex XHR7.5-130 0-7.5V, 0-130A, with opt M9B (RS-232C), Constant current or voltage mode. High efficiency, small footprint.
835 Xantrex XTS15-4 0-15V, 0-4A Constant current or voltage mode. With opt GPIB-M
836 Xantrex HPD15-20S 0-15V, 0-20A Constant current or voltage mode. Digital display with analog bargraph.
837 Xantrex XTS60-1 0-60V, 0-1A Constant current or voltage mode. Digital display with analog bargraph
838 Xantrex XTS60-1 0-60V, 0-1A Dual output. Constant current or voltage mode. Digital display with analog bargraph.
839 Xantrex XTS250-0.25 0-250V, 0-250mA. Constant voltage or current mode. 3 1/2 digit digital meters
840 Xantrex 6060D 0-60 @ 0-1A dual output.. Same as two Xantrex XTS60-1 mounted in one chassi.
841 Yokogawa 321345A Insulation tester. Measure up to 2000 MOhm, 1000V test voltage. Carrying case
842 Yokogawa 2404-15 Insulation tester Megohm meter.Up to 2000 MOhm, 300VAC test voltage, Handcrank generator, no batt or
AC power needed to do the testin Dim: 7"x4x4. Carrying case
843 Yokogawa 700988 400MHz, 10MOhm, x10 oscilloscope probe. 600V max

Electronic test equipment, Oscilloscope, Spectrum, Analyzer ,DMM

Recommended

Recommended

More Related Content

What's hot

What's hot (19)

Similar to Electronic test equipment, Oscilloscope, Spectrum, Analyzer ,DMM

Similar to Electronic test equipment, Oscilloscope, Spectrum, Analyzer ,DMM (20)

More from Emily Tan

More from Emily Tan (20)

Recently uploaded

Recently uploaded (20)

Electronic test equipment, Oscilloscope, Spectrum, Analyzer ,DMM