DATE: 2019.05
- Design of a gearbox as a power transmission system
- Calculation of mechanical design parameters
- Mechanical design process
- Bearing selection from a given catalog
- Using ISO standards for a mechanical design process
In this project, a suitable gearbox is designed, and bearings are selected for the given prime mover in a screw conveyor machine. Screw conveyors are used for granular material transporting applications such as wheat. The granular medium can be transported efficiently to any desired position, ie. horizontal, vertical or sloped position.
Gurgaon ✡️9711147426✨Call In girls Gurgaon Sector 51 escort service
Gearbox Design and Bearing Selection
1. MECHANICAL ENGINEERING DEPARTMENT
ME 308
MACHINE ELEMENTS II
Spring 2018
Project Title : Gearbox Design and Bearing Selection
Project Group : 72
Prepared by : Samet Baykul
Date Submitted : 8.05.2019
Used Data Set : 2
4. ii
I hereby declare that all information in this document has been obtained and
presented in accordance with academic rules and ethical conduct. I also
declare that, as require by these rules and conduct, I have fully cited and
referenced all material and results that are not original to this work.
Name, Last Name : Samet Baykul
Signature :
7. 5
1. Introduction
In this project, a suitable gearbox is designed, and bearings are selected for the given
prime mover in a screw conveyor machine. Screw conveyors are used for granular material
transporting applications such as wheat. The granular medium can be transported
efficiently to any desired position, ie. horizontal, vertical or sloped position. The
mechanism illustrated in the Figure 1, a horizontal conveyor machine.
During design phase, AGMA and ISO standards are used in order to calculate required
dimensions, orientations and gear types. Transmitted power, and applied forces are
calculated by using geometric relations.
Bevel gears and helical gears attached to shafts transmit power from the prime mover
to the machine. The shafts are supported by tapered roller bearings and deep groove ball
bearings. The gearbox reduces the output shaft speed relative to the input shaft speed.
This study allows me to apply my knowledge from the ME308 course and knowledge
from previous years to real life problems. During the calculations, ME308 class notes,
catalogues, and Shigley’s Mechanical Engineering Design textbook were utilized.
13. 11
Since contact stress is higher than the bending stress, pinion and gear are more
critical for surface failure. So, our mn value becomes 2.5 according to table of
recommended module value.
Module = 2.5mm
No interference.
22. 20
4.Other Considerations
4.1. Mounting of Shaft 1
While mounting ball and roller bearings, selecting the right mounting type is
important. Besides correct tools should be used.
In this project, deep groove ball bearings have been used for shaft 1 and 303 series
tapered roller bearing used for shaft 3. Deep groove ball bearings have numerous
advantages for this project. Deep groove ball bearings are simple, non-separable,
suitable for higher speeds and are robust in operation, requiring little maintenance.
They are the most widely used bearing type, available in many designs, variants and
sizes. Tapered roller bearings have tapered inner and outer ring raceways and tapered
rollers. They are designed to accommodate combined loads or simultaneously acting
radial and axial loads.
Key is a machine element used to connect a rotating machine element to a shaft.
The key prevents relative rotation between the two parts and may enable torque
transmission. Shaft and rotating machine element should have a keyway and key seat.
The whole system is called as a keyed joint.
Seals are purpose of retaining the lubricant within the bearing and to prevent
humidity and impurities. It is very important since if any particle interferes between
shaft and bearing the bearing performance will be affected negatively even if that
particles are too small.
23. 21
4.2. Lubrication of Gearbox
For the helical gears in the gearbox, a proper lubrication system can increase the
heat dissipation rate from the moving parts such as shafts, bearings etc. Lubrication
system also prevents the wear and corrosion on the surfaces of the components inside
the machine.
In this project, oil bath lubrication system is used. In this lubrication system, oil
in the casing which is up to a level that one of the gears (larger one of the gear pair)
is submerged in oil reservoir and lubricating while it is rotating with the mating gear.
In this system, oil level and temperature are important and must be carried out.
Oil level must be optimum that if it is too high there will be excessive agitation and if
it is too low, it cannot cool down the gears. For the temperature problem, we could add
heat sink to carry away the heat more efficiently. In this project, fins seem to be
enough in order to provide required heat dissipation.
24. 22
5. Results
Table 1: Helical Gear Set Manufacturing Data
Pinion Gear
Part Name / Index Helical Pinion Helical Gear
Material HBN 360 HBN 360
Normal Pressure Angle 20 20
Normal Module 2.50 mm 2.50 mm
Helix Angle 30 30
Pitch Diameter 30.00 mm 125.00 mm
Face Width, F 25.00 mm 25.00 mm
Number of Teeth 12 50
Table 2: Bevel Gear Set Manufacturing Data
Pinion Gear
Part Name / Index Bevel Pin Bevel Gear
Material HBN 380 HBN 380
Pressure Angle 20 20
Module, m 8 mm 8 mm
Pitch Diameter 120.00 mm 584.00 mm
Face Width, F 64.00 mm 64.00 mm
Number of Teeth 15 73
25. 23
6. Discussion
In this project, the main task was to design a gearbox that functions as the power
transmission system and to choose suitable bearings for the shafts in the gearbox.
In the design of gearbox, two different gear pair were designed. First one is the
helical gear mesh, it was designed by using the data given in the data set. The
requirements for the helical gear set were met for a certain module that was found
iteratively. The second one, the bevel gear mesh. Similarly, the main parameter that
resolved the gear mesh design was the module as well. In calculation of both of these
gear pairs, AGMA stress equations were utilized with ISO standards.
After the characteristics of the gear pairs were determined, the shafts that these
gear pairs operated on were considered. The calculation of the shaft parameters was
directly related to the selection of bearings on the gearbox.
Throughout this project, the calculations were carried out on Mathcad. In all
calculation section in this document, only the final calculation results were shown
instead of placing all iterations.
As a conclusion, this project was a challenging design task which consist of
different important calculations for cases in real-life.
26. References
[1] Shiegly’s Mechanical Design, Budynas,R.G., Nisbett, J.K., 10th Edition, 2015,
McGraw Hill
[2] Notes to be used in examinations,
http://courses.me.metu.edu.tr/courses/me308/
[3] Bearing Catalogue, http://courses.me.metu.edu.tr/courses/me308/