Groschopp 05150 specsheet
•
0 likes•21 views
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, 50Hz, and speed of 1220 rpm. Key specifications include a rating of 1215.2 rpm at 0.8 lb-in of torque drawing 0.23 amps of current. Charts show torque and efficiency at various speeds both when cold and hot. The motor has a continuous duty cycle and efficiency of 26.2%. It stalls at 0.30 amps and 0.97 lb-in of torque.
Report
Share
Report
Share
Download to read offline
Recommended
Groschopp 05130 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, speed of 1500 rpm, output of 15 watts, and efficiency of 31.4%. The motor draws 0.25 amps of current at full speed of 1495.5 rpm and generates 0.8 lb-in of torque. Charts show the motor's speed and torque characteristics when cold and hot, with torque ranging from 0 to 1.4 lb-in over 0 to 1800 rpm.
Groschopp 05157 specsheet
This document provides specifications for an AC 3 Phase 6540 TENV motor with a rating of 1207.1 rpm and 1.5 lb-in of torque consuming 0.23 amps of current. The motor produces 21 watts of output power equivalent to 0.0279 horsepower. Under breakdown and pullup conditions, the motor reaches lower speeds and higher torques. The motor has a continuous duty cycle with peak efficiencies of 36% for the gearbox, motor, and overall system. It produces higher current and torque under start or stall conditions. A graph shows efficiency decreases with increasing torque from a peak of 90% at lower torques.
Groschopp 05122 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 115V, speed of 1490 rpm, and no gearbox. Key specifications include a rated speed of 1491.8 rpm, torque of 1.0 lb-in, current of 0.49 amps, output power of 17 watts, and output horsepower of 0.0227 HP. The motor has a breakdown speed of 1024.29 rpm, pullup torque of 1.06 lb-in, and continuous duty cycle. Start/stall conditions are a current of 0.71 amps and torque of 1.06 lb-in. A graph shows efficiency levels between 0-1600 rpm.
Groschopp 05126 specsheet
The document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 115V, speed of 3150 rpm, and no gearbox. Key specifications include a rating of 3152.3 rpm and 1.1 lb-in of torque at 0.69 amps and 41 watts of output. The motor has a breakdown speed of 2462.14 rpm and pullup speed of 0 rpm. It has a continuous duty cycle and system efficiency of 52.6%. Start/stall conditions are 1.58 amps and 0.93 lb-in of torque. Performance charts show efficiency and torque curves versus speed in both cold and hot conditions.
Groschopp 05128 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, speed of 1490 rpm, and no gearbox. Key specifications include a rating of 1493.1 rpm and 1.0 lb-in of torque drawing 0.33 amps of current. Performance tests found a breakdown speed of 1015.34 rpm and pullup speed of 0 rpm. The motor has a continuous duty cycle and system efficiency of 28.6%. Startup requires 0.43 amps and produces 1.27 lb-in of torque. A graph shows efficiency decreases with increasing torque from 90% at 0 rpm to 20% at 1600 rpm.
Groschopp 05137 specsheet
The document provides specifications for an AC 3 Phase 6540 TENV motor with a rating of 1563.8 rpm and 1.2lb-in of torque consuming 0.25 amps of current. The motor produces 23 watts of output power and 0.0304 HP. Under cold conditions, the motor reaches 948.42 rpm with 2.64 lb-in of torque and stalls at 0 rpm with 2.39lb-in of torque. The motor, gearbox, and system efficiencies are listed as 37.8% and it can operate continuously under any load conditions.
Groschopp 05317 specsheet
This document provides specifications for an AC 1 Ph 8060 TENV motor with a rating of 2614.4 rpm, 0.1180 HP, and 88 watts of output power. The motor runs at 2610 rpm on 230v 50Hz power and has a maximum torque of 4.27 lb-in. Charts show the motor's speed and efficiency at different torque levels both when cold and hot.
Groschopp 05300 specsheet
The document provides specifications for an AC 3 Phase 8060 TENV motor with a rating of 1350 rpm and 5.1 lb-in of torque. It lists various performance metrics like breakdown torque, pullup torque, start/stall conditions, and efficiency curves across a range of torques and speeds. The motor has a continuous duty cycle and 59.1% efficiency. It was prepared by Groschopp.com and is available from Electromate.
Recommended
Groschopp 05130 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, speed of 1500 rpm, output of 15 watts, and efficiency of 31.4%. The motor draws 0.25 amps of current at full speed of 1495.5 rpm and generates 0.8 lb-in of torque. Charts show the motor's speed and torque characteristics when cold and hot, with torque ranging from 0 to 1.4 lb-in over 0 to 1800 rpm.
Groschopp 05157 specsheet
This document provides specifications for an AC 3 Phase 6540 TENV motor with a rating of 1207.1 rpm and 1.5 lb-in of torque consuming 0.23 amps of current. The motor produces 21 watts of output power equivalent to 0.0279 horsepower. Under breakdown and pullup conditions, the motor reaches lower speeds and higher torques. The motor has a continuous duty cycle with peak efficiencies of 36% for the gearbox, motor, and overall system. It produces higher current and torque under start or stall conditions. A graph shows efficiency decreases with increasing torque from a peak of 90% at lower torques.
Groschopp 05122 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 115V, speed of 1490 rpm, and no gearbox. Key specifications include a rated speed of 1491.8 rpm, torque of 1.0 lb-in, current of 0.49 amps, output power of 17 watts, and output horsepower of 0.0227 HP. The motor has a breakdown speed of 1024.29 rpm, pullup torque of 1.06 lb-in, and continuous duty cycle. Start/stall conditions are a current of 0.71 amps and torque of 1.06 lb-in. A graph shows efficiency levels between 0-1600 rpm.
Groschopp 05126 specsheet
The document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 115V, speed of 3150 rpm, and no gearbox. Key specifications include a rating of 3152.3 rpm and 1.1 lb-in of torque at 0.69 amps and 41 watts of output. The motor has a breakdown speed of 2462.14 rpm and pullup speed of 0 rpm. It has a continuous duty cycle and system efficiency of 52.6%. Start/stall conditions are 1.58 amps and 0.93 lb-in of torque. Performance charts show efficiency and torque curves versus speed in both cold and hot conditions.
Groschopp 05128 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, speed of 1490 rpm, and no gearbox. Key specifications include a rating of 1493.1 rpm and 1.0 lb-in of torque drawing 0.33 amps of current. Performance tests found a breakdown speed of 1015.34 rpm and pullup speed of 0 rpm. The motor has a continuous duty cycle and system efficiency of 28.6%. Startup requires 0.43 amps and produces 1.27 lb-in of torque. A graph shows efficiency decreases with increasing torque from 90% at 0 rpm to 20% at 1600 rpm.
Groschopp 05137 specsheet
The document provides specifications for an AC 3 Phase 6540 TENV motor with a rating of 1563.8 rpm and 1.2lb-in of torque consuming 0.25 amps of current. The motor produces 23 watts of output power and 0.0304 HP. Under cold conditions, the motor reaches 948.42 rpm with 2.64 lb-in of torque and stalls at 0 rpm with 2.39lb-in of torque. The motor, gearbox, and system efficiencies are listed as 37.8% and it can operate continuously under any load conditions.
Groschopp 05317 specsheet
This document provides specifications for an AC 1 Ph 8060 TENV motor with a rating of 2614.4 rpm, 0.1180 HP, and 88 watts of output power. The motor runs at 2610 rpm on 230v 50Hz power and has a maximum torque of 4.27 lb-in. Charts show the motor's speed and efficiency at different torque levels both when cold and hot.
Groschopp 05300 specsheet
The document provides specifications for an AC 3 Phase 8060 TENV motor with a rating of 1350 rpm and 5.1 lb-in of torque. It lists various performance metrics like breakdown torque, pullup torque, start/stall conditions, and efficiency curves across a range of torques and speeds. The motor has a continuous duty cycle and 59.1% efficiency. It was prepared by Groschopp.com and is available from Electromate.
Groschopp 05136 specsheet
The document provides specifications for an AC 3 Phase 6540 TEFC motor with a voltage of 230V and speed of 1570 rpm. The motor has a rating of 1569.7 rpm and 1.4 lb-in of torque drawing 0.31 amps of current and producing 27 watts of output power equivalent to 0.0357 HP. The motor has a continuous duty cycle with peak efficiency of 34.4% and can produce up to 2.51 lb-in of torque when starting or stalling, drawing 0.59 amps of current. Performance charts show torque and efficiency at varying speeds. The motor is sold and serviced by Electromate.
Groschopp 05132 specsheet
The document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, frequency of 60Hz, and speed of 3100rpm. Key specifications include a rating of 3100.8rpm at 1.0lb-in of torque drawing 0.38amps, with an output of 38watts and 0.0513HP. Startup current is 0.78amps with 0.75lb-in of torque. Efficiency is provided in a graph showing the relationship between speed, torque, and efficiency for both cold and hot operating conditions. The motor has a 4uF 440V capacitor and is sold and serviced by Electromate.
Groschopp 01011 specsheet
This document provides specifications for a 12V DC motor including its voltage, speed, torque, current, output power, efficiency ratings, start/stall conditions, and speed vs. torque and efficiency curves. The motor runs at 2750 rpm without a gearbox, has a maximum torque of 6.31 lb-in, efficiency of 61.1%, and was manufactured by Groschopp.com.
Groschopp 47779 specsheet
This document provides specifications for a small AC motor including its voltage, speed, gearbox ratio, product ID number, ratings for speed, torque, current and output. It also details startup, stall, efficiency and speed vs torque performance curves for the motor both cold and hot. The motor is to be continuously run and is sold and serviced by Electromate.
Groschopp 74529 specsheet
This document provides specifications for a motor including its AC voltage, speed in RPM, gearbox ratio, product ID number, ratings for speed, torque, current and output. It also lists breakdown, pullup, duty cycle, and start/stall condition details. Charts show torque and efficiency at varying speeds when cold and hot. The motor is sold and serviced by Electromate.
Groschopp 74527 specsheet
This document provides specifications for an AC 3 Phase 8040 TENV motor with a 230V 50Hz voltage and 1350RPM speed coupled to a RA 2600T 60:1 ratio gearbox. Key specifications include a 22.8RPM speed and 88.8lb-in torque at 0.42A and 24W output, with continuous duty cycle and maximum efficiencies of 50.9% for the motor and 24.8% for the overall system. Startup conditions draw 1.17A and produce 256.41lb-in of torque. Performance charts also show torque and speed values across a range of RPMs.
Groschopp 05120 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 115V, speed of 1480 rpm, and no gearbox. Key specifications include a rated speed of 1483 rpm, torque of 1.1 lb-in, current of 0.64 amps, output of 20 watts, and efficiency of 30.6%. Performance data is provided showing torque and speed curves for cold and hot operation.
Groschopp 05159 specsheet
This document provides specifications for an AC 3 Phase 6540 TENV motor with a voltage of 230V, frequency of 50Hz, and speed of 2710rpm without a gearbox. Key specifications include a rating of 2710rpm and 1.5lb-in of torque at 0.34amps and 48watts of output, or 0.0645HP. Breakdown and pullup torque and speed are also listed, along with duty cycle, efficiency curves, and start/stall conditions. The motor is sold and serviced by Electromate.
Groschopp 05130 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, speed of 1500 rpm, output of 15 watts, and efficiency of 31.4%. The motor draws 0.25 amps of current at full speed of 1495.5 rpm and generates 0.8 lb-in of torque. Charts show its torque and efficiency characteristics at different speeds both when cold and hot.
Groschopp 05157 specsheet
This document provides specifications for an AC 3 Phase 6540 TENV motor with a rating of 1207.1 rpm and 1.5 lb-in of torque consuming 0.23 amps of current. The motor produces 21 watts of output power equivalent to 0.0279 horsepower. Under breakdown and pullup conditions, the motor reaches lower speeds and higher torques. The motor has a continuous duty cycle with peak efficiencies of 36% for the gearbox, motor, and overall system. Startup requires 0.40 amps of current producing 2.55 lb-in of torque. A graph shows efficiency decreases with speed above 750 rpm.
Groschopp 05128 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, speed of 1490 rpm, and output of 18 watts. Key specifications include a rating of 1493.1 rpm and 1.0 lb-in of torque at 0.33 amps of current. The motor has a breakdown speed of 1015.34 rpm and pullup torque of 1.27lb-in. It has a continuous duty cycle and system efficiency of 28.6%. Start/stall conditions are 0.43 amps and 1.27 lb-in of torque. A graph shows efficiency versus torque from 0 to 1600 rpm. It is sold and serviced by Electromate.
Groschopp 05122 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 115V, speed of 1490 rpm, and no gearbox. Key specifications include a rated speed of 1491.8 rpm, torque of 1.0 lb-in, current of 0.49 amps, output power of 17 watts, and output horsepower of 0.0227 HP. The motor has a breakdown speed of 1024.29 rpm, pullup torque of 1.06 lb-in, and continuous duty cycle. Start/stall conditions are a current of 0.71 amps and torque of 1.06 lb-in. A graph shows efficiency levels between 0-1600 rpm.
Groschopp 05126 specsheet
The document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 115V, speed of 3150 rpm, and no gearbox. Key specs include a rating of 3152.3 rpm and 1.1 lb-in of torque at 0.69 amps and 41 watts of output. The motor has a breakdown speed of 2462.14 rpm and pullup speed of 0 rpm. It has a continuous duty cycle and system efficiency of 52.6%. Start/stall conditions are 1.58 amps and 0.93 lb-in of torque. Performance charts show efficiency versus torque and speed.
Groschopp 05320 specsheet
This document provides specifications for an AC 1 Ph 8040 TENV motor with a voltage of 115V, speed of 1510 rpm, and no gearbox. Key specifications include a rated speed of 1507.5 rpm, torque of 2.4 lb-in, current of 0.76 amps, output of 42 watts, and efficiency of 47.8%. Performance charts show torque and speed values at various RPMs as well as efficiency curves for cold and hot operation.
Groschopp 05320 specsheet
This document provides specifications for an AC 1 Ph 8040 TENV motor with a voltage of 115V, speed of 1510 rpm, and no gearbox. Key specifications include a rated speed of 1507.5 rpm, torque of 2.4 lb-in, current of 0.76 amps, output of 42 watts, and efficiency of 47.8%. Start/stall conditions are listed as 1.34 amps current and 2.28 lb-in torque. A graph shows efficiency and speed versus torque from 0 to 1800 rpm. Notes indicate a 10uF 250V capacitor. The motor is sold and serviced by Electromate.
Groschopp 05137 specsheet
The document provides specifications for an AC 3 Phase 6540 TENV motor with a rating of 1563.8 rpm and 1.2lb-in of torque consuming 0.25 amps of current. The motor produces 23 watts of output power and 0.0304 HP. Under cold conditions, the motor reaches 948.42 rpm with 2.64 lb-in of torque and stalls at 0 rpm with 2.39lb-in of torque. The motor, gearbox, and system efficiencies are listed as 37.8% and it can operate continuously under start/stall conditions of 0.52 amps and 2.39 lb-in of torque.
Groschopp 05301 specsheet
This document provides specifications for an AC 3 Phase 8060 TEFC motor with a voltage of 230V, frequency of 50Hz, and speed of 1360rpm without a gearbox. Key specifications include a rated speed of 1355rpm, torque of 7.9lb-in, current of 1.02amps, output of 127watts, and efficiency of 56.4%. Start/stall conditions are listed as 2.69amps current and 19.94lb-in torque. A graph shows efficiency and speed curves versus torque. The motor is sold and serviced by Electromate.
Groschopp 05301 specsheet
This document provides specifications for an AC 3 Phase 8060 TEFC motor with a voltage of 230V, frequency of 50Hz, and speed of 1360rpm without a gearbox. Key specifications include a rated speed of 1355rpm, torque of 7.9lb-in, current of 1.02amps, output of 127watts, and efficiency of 56.4%. Start/stall conditions are listed as 2.69amps current and 19.94lb-in torque. A graph shows efficiency and speed curves versus torque. The motor is sold and serviced by Electromate.
Groschopp 05120 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 115V, speed of 1480 rpm, and no gearbox. Key specifications include a rated speed of 1483 rpm, torque of 1.1 lb-in, current of 0.64 amps, output of 20 watts, and efficiency of 30.6%. Performance data is provided showing torque and speed curves for cold and hot operation.
Groschopp 05148 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, frequency of 50Hz, and speed of 1190 rpm. Key specifications include a rating of 1189.4 rpm and 1.1 lb-in of torque drawing 0.31 amps of current. Performance tests found breakdown torque of 1.59 lb-in at 790.15 rpm and start/stall torque of 1.37 lb-in drawing 0.39 amps. A graph shows efficiency peaks at 25.4% between 450-1050 rpm. It has a 3.5uF 440V capacitor and is sold and serviced by Electromate.
Groschopp 05148 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, frequency of 50Hz, and speed of 1190 rpm. Key specifications include a rating of 1189.4 rpm and 1.1 lb-in of torque drawing 0.31 amps of current. Performance tests found breakdown torque of 1.59 lb-in at 790.15 rpm and start/stall torque of 1.37 lb-in drawing 0.39 amps. A graph shows efficiency peaks at 25.4% between 450-1050 rpm. It has a 3.5uF 440V capacitor and is sold and serviced by Electromate.
Groschopp 05136 specsheet
The document provides specifications for an AC 3 Phase 6540 TEFC motor with a voltage of 230V and speed of 1570 rpm. Key specifications include a rating of 1569.7 rpm and 1.4 lb-in of torque drawing 0.31 amps of current. The motor produces 27 watts of output power and 0.0357 HP. Startup conditions draw 0.59 amps with maximum torque of 2.51 lb-in. Efficiency is shown to vary from 10-90% over torque ranges from 0.3-2.4 lb-in. The motor has a continuous duty cycle and is sold and serviced by Electromate.
More Related Content
What's hot
Groschopp 05136 specsheet
The document provides specifications for an AC 3 Phase 6540 TEFC motor with a voltage of 230V and speed of 1570 rpm. The motor has a rating of 1569.7 rpm and 1.4 lb-in of torque drawing 0.31 amps of current and producing 27 watts of output power equivalent to 0.0357 HP. The motor has a continuous duty cycle with peak efficiency of 34.4% and can produce up to 2.51 lb-in of torque when starting or stalling, drawing 0.59 amps of current. Performance charts show torque and efficiency at varying speeds. The motor is sold and serviced by Electromate.
Groschopp 05132 specsheet
The document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, frequency of 60Hz, and speed of 3100rpm. Key specifications include a rating of 3100.8rpm at 1.0lb-in of torque drawing 0.38amps, with an output of 38watts and 0.0513HP. Startup current is 0.78amps with 0.75lb-in of torque. Efficiency is provided in a graph showing the relationship between speed, torque, and efficiency for both cold and hot operating conditions. The motor has a 4uF 440V capacitor and is sold and serviced by Electromate.
Groschopp 01011 specsheet
This document provides specifications for a 12V DC motor including its voltage, speed, torque, current, output power, efficiency ratings, start/stall conditions, and speed vs. torque and efficiency curves. The motor runs at 2750 rpm without a gearbox, has a maximum torque of 6.31 lb-in, efficiency of 61.1%, and was manufactured by Groschopp.com.
Groschopp 47779 specsheet
This document provides specifications for a small AC motor including its voltage, speed, gearbox ratio, product ID number, ratings for speed, torque, current and output. It also details startup, stall, efficiency and speed vs torque performance curves for the motor both cold and hot. The motor is to be continuously run and is sold and serviced by Electromate.
Groschopp 74529 specsheet
This document provides specifications for a motor including its AC voltage, speed in RPM, gearbox ratio, product ID number, ratings for speed, torque, current and output. It also lists breakdown, pullup, duty cycle, and start/stall condition details. Charts show torque and efficiency at varying speeds when cold and hot. The motor is sold and serviced by Electromate.
Groschopp 74527 specsheet
This document provides specifications for an AC 3 Phase 8040 TENV motor with a 230V 50Hz voltage and 1350RPM speed coupled to a RA 2600T 60:1 ratio gearbox. Key specifications include a 22.8RPM speed and 88.8lb-in torque at 0.42A and 24W output, with continuous duty cycle and maximum efficiencies of 50.9% for the motor and 24.8% for the overall system. Startup conditions draw 1.17A and produce 256.41lb-in of torque. Performance charts also show torque and speed values across a range of RPMs.
Groschopp 05120 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 115V, speed of 1480 rpm, and no gearbox. Key specifications include a rated speed of 1483 rpm, torque of 1.1 lb-in, current of 0.64 amps, output of 20 watts, and efficiency of 30.6%. Performance data is provided showing torque and speed curves for cold and hot operation.
Groschopp 05159 specsheet
This document provides specifications for an AC 3 Phase 6540 TENV motor with a voltage of 230V, frequency of 50Hz, and speed of 2710rpm without a gearbox. Key specifications include a rating of 2710rpm and 1.5lb-in of torque at 0.34amps and 48watts of output, or 0.0645HP. Breakdown and pullup torque and speed are also listed, along with duty cycle, efficiency curves, and start/stall conditions. The motor is sold and serviced by Electromate.
What's hot (8)
Similar to Groschopp 05150 specsheet
Groschopp 05130 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, speed of 1500 rpm, output of 15 watts, and efficiency of 31.4%. The motor draws 0.25 amps of current at full speed of 1495.5 rpm and generates 0.8 lb-in of torque. Charts show its torque and efficiency characteristics at different speeds both when cold and hot.
Groschopp 05157 specsheet
This document provides specifications for an AC 3 Phase 6540 TENV motor with a rating of 1207.1 rpm and 1.5 lb-in of torque consuming 0.23 amps of current. The motor produces 21 watts of output power equivalent to 0.0279 horsepower. Under breakdown and pullup conditions, the motor reaches lower speeds and higher torques. The motor has a continuous duty cycle with peak efficiencies of 36% for the gearbox, motor, and overall system. Startup requires 0.40 amps of current producing 2.55 lb-in of torque. A graph shows efficiency decreases with speed above 750 rpm.
Groschopp 05128 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, speed of 1490 rpm, and output of 18 watts. Key specifications include a rating of 1493.1 rpm and 1.0 lb-in of torque at 0.33 amps of current. The motor has a breakdown speed of 1015.34 rpm and pullup torque of 1.27lb-in. It has a continuous duty cycle and system efficiency of 28.6%. Start/stall conditions are 0.43 amps and 1.27 lb-in of torque. A graph shows efficiency versus torque from 0 to 1600 rpm. It is sold and serviced by Electromate.
Groschopp 05122 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 115V, speed of 1490 rpm, and no gearbox. Key specifications include a rated speed of 1491.8 rpm, torque of 1.0 lb-in, current of 0.49 amps, output power of 17 watts, and output horsepower of 0.0227 HP. The motor has a breakdown speed of 1024.29 rpm, pullup torque of 1.06 lb-in, and continuous duty cycle. Start/stall conditions are a current of 0.71 amps and torque of 1.06 lb-in. A graph shows efficiency levels between 0-1600 rpm.
Groschopp 05126 specsheet
The document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 115V, speed of 3150 rpm, and no gearbox. Key specs include a rating of 3152.3 rpm and 1.1 lb-in of torque at 0.69 amps and 41 watts of output. The motor has a breakdown speed of 2462.14 rpm and pullup speed of 0 rpm. It has a continuous duty cycle and system efficiency of 52.6%. Start/stall conditions are 1.58 amps and 0.93 lb-in of torque. Performance charts show efficiency versus torque and speed.
Groschopp 05320 specsheet
This document provides specifications for an AC 1 Ph 8040 TENV motor with a voltage of 115V, speed of 1510 rpm, and no gearbox. Key specifications include a rated speed of 1507.5 rpm, torque of 2.4 lb-in, current of 0.76 amps, output of 42 watts, and efficiency of 47.8%. Performance charts show torque and speed values at various RPMs as well as efficiency curves for cold and hot operation.
Groschopp 05320 specsheet
This document provides specifications for an AC 1 Ph 8040 TENV motor with a voltage of 115V, speed of 1510 rpm, and no gearbox. Key specifications include a rated speed of 1507.5 rpm, torque of 2.4 lb-in, current of 0.76 amps, output of 42 watts, and efficiency of 47.8%. Start/stall conditions are listed as 1.34 amps current and 2.28 lb-in torque. A graph shows efficiency and speed versus torque from 0 to 1800 rpm. Notes indicate a 10uF 250V capacitor. The motor is sold and serviced by Electromate.
Groschopp 05137 specsheet
The document provides specifications for an AC 3 Phase 6540 TENV motor with a rating of 1563.8 rpm and 1.2lb-in of torque consuming 0.25 amps of current. The motor produces 23 watts of output power and 0.0304 HP. Under cold conditions, the motor reaches 948.42 rpm with 2.64 lb-in of torque and stalls at 0 rpm with 2.39lb-in of torque. The motor, gearbox, and system efficiencies are listed as 37.8% and it can operate continuously under start/stall conditions of 0.52 amps and 2.39 lb-in of torque.
Groschopp 05301 specsheet
This document provides specifications for an AC 3 Phase 8060 TEFC motor with a voltage of 230V, frequency of 50Hz, and speed of 1360rpm without a gearbox. Key specifications include a rated speed of 1355rpm, torque of 7.9lb-in, current of 1.02amps, output of 127watts, and efficiency of 56.4%. Start/stall conditions are listed as 2.69amps current and 19.94lb-in torque. A graph shows efficiency and speed curves versus torque. The motor is sold and serviced by Electromate.
Groschopp 05301 specsheet
This document provides specifications for an AC 3 Phase 8060 TEFC motor with a voltage of 230V, frequency of 50Hz, and speed of 1360rpm without a gearbox. Key specifications include a rated speed of 1355rpm, torque of 7.9lb-in, current of 1.02amps, output of 127watts, and efficiency of 56.4%. Start/stall conditions are listed as 2.69amps current and 19.94lb-in torque. A graph shows efficiency and speed curves versus torque. The motor is sold and serviced by Electromate.
Groschopp 05120 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 115V, speed of 1480 rpm, and no gearbox. Key specifications include a rated speed of 1483 rpm, torque of 1.1 lb-in, current of 0.64 amps, output of 20 watts, and efficiency of 30.6%. Performance data is provided showing torque and speed curves for cold and hot operation.
Groschopp 05148 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, frequency of 50Hz, and speed of 1190 rpm. Key specifications include a rating of 1189.4 rpm and 1.1 lb-in of torque drawing 0.31 amps of current. Performance tests found breakdown torque of 1.59 lb-in at 790.15 rpm and start/stall torque of 1.37 lb-in drawing 0.39 amps. A graph shows efficiency peaks at 25.4% between 450-1050 rpm. It has a 3.5uF 440V capacitor and is sold and serviced by Electromate.
Groschopp 05148 specsheet
This document provides specifications for an AC 1 Ph 6540 TEFC motor with a voltage of 230V, frequency of 50Hz, and speed of 1190 rpm. Key specifications include a rating of 1189.4 rpm and 1.1 lb-in of torque drawing 0.31 amps of current. Performance tests found breakdown torque of 1.59 lb-in at 790.15 rpm and start/stall torque of 1.37 lb-in drawing 0.39 amps. A graph shows efficiency peaks at 25.4% between 450-1050 rpm. It has a 3.5uF 440V capacitor and is sold and serviced by Electromate.
Groschopp 05136 specsheet
The document provides specifications for an AC 3 Phase 6540 TEFC motor with a voltage of 230V and speed of 1570 rpm. Key specifications include a rating of 1569.7 rpm and 1.4 lb-in of torque drawing 0.31 amps of current. The motor produces 27 watts of output power and 0.0357 HP. Startup conditions draw 0.59 amps with maximum torque of 2.51 lb-in. Efficiency is shown to vary from 10-90% over torque ranges from 0.3-2.4 lb-in. The motor has a continuous duty cycle and is sold and serviced by Electromate.
Groschopp 05300 specsheet
The document provides specifications for an AC 3 Phase 8060 TENV motor with a rating of 1350 rpm and 5.1 lb-in of torque. It lists various operating parameters like current, output, efficiency, start/stall conditions, and speed vs. torque and efficiency curves. The motor has no gearbox and was produced by Groschopp.com for product ID 5300.
Groschopp 66378 specsheet
This document provides specifications for an AC motor including its voltage, speed, gearbox ratio, and performance metrics like torque and efficiency at varying speeds. Key specifications include a voltage of 115v, speed of 1510rpm, gearbox ratio of 90:1, and torque of 115.33lb-in at start/stall. Charts show torque and efficiency curves across a range of speeds from 0-225rpm.
Groschopp 05154 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, 50Hz, and speed of 2580 rpm. Key specifications include a rating of 2582.3 rpm and 1.0 lb-in of torque at 0.33 amps of current and 32 watts of output power. Charts show torque and efficiency curves for the motor when cold and hot.
Groschopp 05154 specsheet
This document provides specifications for an AC 1 Ph 6540 TENV motor with a voltage of 230V, 50Hz, and speed of 2580 rpm. Key specifications include a rating of 2582.3 rpm and 1.0 lb-in of torque at 0.33 amps and 32 watts of output. Breakdown and pullup tests were also performed. The motor has a continuous duty cycle and system efficiency of 47.6%. Start/stall conditions are 0.66 amps and 0.83 lb-in of torque. A graph shows efficiency versus torque from 0-2700 rpm. Notes indicate a 4uF 440V capacitor. The motor is sold and serviced by Electromate.
Groschopp 47756 specsheet
This document provides specifications for an AC motor including its voltage, speed, gearbox ratio, product ID, ratings for speed, torque, current and output. It also details breakdown, pullup, duty cycle, efficiency and start/stall conditions. Performance curves are shown for speed, torque and efficiency under cold and hot operating conditions. Notes indicate it uses a 16uF 250V capacitor and is sold and serviced by Electromate.
Groschopp 47756 specsheet
This document provides specifications for an AC motor including its voltage, speed, gearbox ratio, product ID, ratings for speed, torque, current and output. It also details breakdown, pullup, duty cycle, efficiency and start/stall conditions. Performance curves are shown for speed, torque and efficiency under cold and hot operating conditions. Notes indicate it uses a 16uF 250V capacitor and is sold and serviced by Electromate.
Similar to Groschopp 05150 specsheet (20)
More from Electromate
Automated screw thread quality checking using SMAC LAR55 actuator new produc...
The document discusses an automated screw thread quality checking solution using SMAC LAR55 actuators. It allows 100% inspection of screw threads to check for issues like oversizing, cross-threading, depth, and pitch. This can help automakers meet higher quality standards by eliminating defective parts and providing immediate feedback. The LAR55's precision Z-theta motion makes it suitable for automatically checking screw threads.
An overview of the various kinematic models in both parallel and serial robot...
This document provides an overview of kinematic models for parallel and serial robotic mechanisms and their suitability for precision applications. It introduces Ilian Bonev, a professor at École de technologie supérieure who is an expert in parallel robots and precision robotics. It then describes some parallel robots that have been developed at the Control and Robotics Laboratory including ones for medical, manufacturing, and research applications. The document concludes with sections on robot calibration methods and the differences between serial and parallel mechanisms.
Galil motion control robotic symposium presentation-linear motion from non-li...
The document discusses non-linear robotic motion control solutions. It describes how Galil Motion Control provides controllers for various types of non-linear robots like SCARA and delta robots. It covers topics like selecting the robot topology, designing each joint, motor selection, forward and inverse kinematics equations, vibration reduction techniques, and examples of implementing motion control for SCARA robots.
Advanced motion controls robotics symposium presentation-open standard tools ...
This document discusses the development of control software for a linear delta robot used in 3D printing. It describes using PLCopen function blocks and XML files to create reusable software components for robot kinematics and handling G-code from slicing programs. Function block diagrams are created to process G-code, set coordinate systems, and represent the overall project logic. The solution involves creating user-defined function blocks to handle the robot's inverse kinematics and translate G-code commands into motions.
Maxon motor ag robotic symposium presentation-impedance control overview and ...
The document discusses impedance control, an approach to robot control that models mechanical systems as electrical circuits using impedance. It defines electrical and mechanical impedance analogously and describes how components like resistors, inductors, and capacitors correspond to dampers, masses, and springs physically. The document outlines applications of impedance control and emphasizes the importance of selecting low-inertia motors, high-efficiency gears, and fast, accurate sensors and controllers. Overall, the document argues that impedance control requires creative engineering of mechanical designs and electrical components.
Kollmorgen robotic symposium presentation-motor design impacts on the optimiz...
The document discusses how motor design impacts the optimization of robotic systems. It explains that frameless motors can enable smaller, lighter and faster robots through their direct drive capabilities and high torque density. The document also covers various motor topologies and important concepts like torque constant, motor size constant, and how they relate to continuous torque capacity, efficiency and losses. Application examples discussed include collaborative robots, surgical robots, and mobile robots.
Harmonic drive llc robotics symposium presentation-designing from the inside ...
The document discusses defining robot performance requirements and how customized solutions from Harmonic Drive can help meet those requirements. It provides an overview of Harmonic Drive's product line and gear technologies, then discusses how mechanical modifications and performance customizations can be made to their gear components and systems to optimize robots for specific design requirements and applications. Customizations like increased accuracy, stiffness, torque properties and materials can be made, with varying levels of difficulty and cost implications discussed.
Thomson Linear Dual Shaft Rail 2DA Modular Specs
This document provides specifications and dimensional drawings for Thomson Industries' Dual Shaft Rail linear guides with modular carriages. It includes part numbers, dimensions, load ratings and descriptions of the components. Linear guides use dual linear race shaft rails and modular carriages with open type Super Smart Ball Bushings. They are used in continuously supported applications requiring rigidity and are adaptable to any drive system.
Thomson Linear 2DA QuickSlide System with Brake
This document provides specifications for Thomson Industries' 2DA QuickSlide system with brake, including:
- It offers manual locking with infinite positioning, no carriage surface deflection when locked, and immediate availability in common sizes.
- The locking mechanism does not increase load on the bearing and allows zero axial movement during locking.
- It provides a fully supported dual shaft assembly for maximum rigidity and unlimited travel.
Thomson Linear RoundRail 2CA Web Universal Carriage Specs
This document contains specifications for Thomson Industries' Twin Shaft Web Linear Guide system. It includes dimensions, part numbers, load ratings and descriptions of the components. The linear guides use a double shaft and welded web design for improved torque strength and deflection characteristics. They are designed to move medium loads with low friction and are commonly used when bridging gaps.
Thomson Linear RoundRail 1VC Double End Supported Specs
The document provides specifications for various FluoroNyliner linear guide components including:
- Pillow blocks, twin pillow blocks, shaft end support blocks, and mounting table tops for different size linear guides ranging from 0.375 to 1.5 inches in diameter.
- It lists the part numbers, dimensions, materials, weights, and other specifications for each component.
- It also includes an illustration of a double end supported linear guide system with pillow blocks, shafts, end supports, and a size B mounting table top.
Thomson Linear RoundRail 2CA Web Flanged Carriage Specs
This document provides specifications for Thomson Industries' Twin Shaft Web Linear Guide system. It includes dimensions, load capacity information, and part numbers for various components of the 2CA linear guide, which features a flanged carriage design and double linear race shaft for improved torque and deflection characteristics. Configuration and installation details are also listed.
Thomson Linear RoundRail Twin Shaft Web 2CA
The document provides specifications for Thomson RoundRail linear guides and components. It includes dimensions, features, and part numbering for twin shaft web linear guides in both vertical and horizontal configurations ranging from 0.5 to 1 inch in diameter. Load capacity charts are provided for different guide sizes and configurations that can support loads between 165 to 3000 pounds depending on the model. Maximum guide lengths are listed as 72 inches and engineering calculations for shaft deflection are also noted.
Thomson Linear RoundRail 1VC Double Unsupported Specs
The document contains specifications for various FluoroNyliner linear guide parts, including dimensions, part numbers, materials, load ratings, and performance notes. It lists 14 different linear guide parts with nominal diameters ranging from 0.375 to 1.5 inches. For each part, it provides dimensions for components like bearing blocks, carriages, and table tops. It also includes general information on specifying linear guides and product notes on materials and lubrication.
Thomson Linear WhisperTrak Actuators
The Thomson WhisperTrak electric linear actuator offers a compact, quiet, and durable solution for applications requiring linear motion. It is particularly well-suited for personal mobility, medical, and rehabilitation equipment due to its small size and silent operation. The actuator provides reliable, maintenance-free movement and has an IP67 rating, making it protected against water and dust. Its flexibility and high performance in a small package make it suitable for a wide range of industries.
Thomson T-Series Profile Rail
The document provides information on the T-Series Ball Profile Rail from Thomson, including:
- It is lightweight, highly flexible, and forgiving, making it suitable for applications with poor misalignment.
- It has a low cost of installation as it can be mounted directly to non-machined bases without special tools.
- It offers industry standard dimensions and dimensions interchangeable with other rail brands, allowing for easy replacement.
Thomson Linear RoundRail Accessories Collapsable Bellows Specs
This document provides specifications for various bellows that can be used to protect slides and shafts. It lists different part numbers for bellows with a range of nominal shaft diameters from 1/4 to 1 1/2 inches. The bellows are made of polyester cover and PVC stiffeners. Dimensions such as length, width, and height are provided for each part number. Some bellows are single shaft while others are dual shaft or for horizontal vs vertical systems. Each bellows comes with attachment pieces like Velcro or mounting brackets.
Thomson Linear Roundrail Dual Shaft Rail 2DA Specs
The document provides specifications for Danaher Motion's dual shaft rail linear guides with integrated carriages. It includes dimensions, load ratings, dynamic capacities, and part numbering for the 2DA series linear guides available in nominal diameters of 0.5, 0.75, and 1.0 inches. Both full and short length carriage options are detailed along with components, material specifications, and the supplier contact information.
Thomson Linear RoundRail Continuous Support 1PC Specs
This document provides specifications for various linear guide assemblies with table tops from Thomson Industries. It includes dimensions, part numbers, load ratings and limit data for single rail linear guides with sizes ranging from M12 to M40 diameter in configurations with 4 pillow blocks, 2 twin pillow blocks or no pillow blocks and size E or F table tops. Mounting details and specifications are provided for the various components including rails, pillow blocks and table tops.
Thomson Linear RoundRail Continuous Support 1PB Specs
The document contains specifications for various continuously supported linear guide assemblies and their components. It lists part numbers, dimensions, load ratings, and other technical specifications for linear guides, support rails, pillow blocks, and bearings. Materials include aluminum alloys and bearings include ball bushings. Linear guides are specified by part number plus length and provide continuous support for applications requiring rigidity.
More from Electromate (20)
Automated screw thread quality checking using SMAC LAR55 actuator new produc...
Automated screw thread quality checking using SMAC LAR55 actuator new produc...
An overview of the various kinematic models in both parallel and serial robot...
An overview of the various kinematic models in both parallel and serial robot...
Galil motion control robotic symposium presentation-linear motion from non-li...
Galil motion control robotic symposium presentation-linear motion from non-li...
Advanced motion controls robotics symposium presentation-open standard tools ...
Advanced motion controls robotics symposium presentation-open standard tools ...
Maxon motor ag robotic symposium presentation-impedance control overview and ...
Maxon motor ag robotic symposium presentation-impedance control overview and ...
Kollmorgen robotic symposium presentation-motor design impacts on the optimiz...
Kollmorgen robotic symposium presentation-motor design impacts on the optimiz...
Harmonic drive llc robotics symposium presentation-designing from the inside ...
Harmonic drive llc robotics symposium presentation-designing from the inside ...
Thomson Linear RoundRail 2CA Web Universal Carriage Specs
Thomson Linear RoundRail 2CA Web Universal Carriage Specs
Thomson Linear RoundRail 1VC Double End Supported Specs
Thomson Linear RoundRail 1VC Double End Supported Specs
Thomson Linear RoundRail 2CA Web Flanged Carriage Specs
Thomson Linear RoundRail 2CA Web Flanged Carriage Specs
Thomson Linear RoundRail 1VC Double Unsupported Specs
Thomson Linear RoundRail 1VC Double Unsupported Specs
Thomson Linear RoundRail Accessories Collapsable Bellows Specs
Thomson Linear RoundRail Accessories Collapsable Bellows Specs
Thomson Linear Roundrail Dual Shaft Rail 2DA Specs
Thomson Linear Roundrail Dual Shaft Rail 2DA Specs
Thomson Linear RoundRail Continuous Support 1PC Specs
Thomson Linear RoundRail Continuous Support 1PC Specs
Thomson Linear RoundRail Continuous Support 1PB Specs
Thomson Linear RoundRail Continuous Support 1PB Specs
Recently uploaded
Observability Concepts EVERY Developer Should Know -- DeveloperWeek Europe.pdf
Monitoring and observability aren’t traditionally found in software curriculums and many of us cobble this knowledge together from whatever vendor or ecosystem we were first introduced to and whatever is a part of your current company’s observability stack.
While the dev and ops silo continues to crumble….many organizations still relegate monitoring & observability as the purview of ops, infra and SRE teams. This is a mistake - achieving a highly observable system requires collaboration up and down the stack.
I, a former op, would like to extend an invitation to all application developers to join the observability party will share these foundational concepts to build on:
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
The choice of an operating system plays a pivotal role in shaping our computing experience. For decades, Microsoft's Windows has dominated the market, offering a familiar and widely adopted platform for personal and professional use. However, as technological advancements continue to push the boundaries of innovation, alternative operating systems have emerged, challenging the status quo and offering users a fresh perspective on computing.
One such alternative that has garnered significant attention and acclaim is Nitrux Linux 3.5.0, a sleek, powerful, and user-friendly Linux distribution that promises to redefine the way we interact with our devices. With its focus on performance, security, and customization, Nitrux Linux presents a compelling case for those seeking to break free from the constraints of proprietary software and embrace the freedom and flexibility of open-source computing.
Building RAG with self-deployed Milvus vector database and Snowpark Container...
This talk will give hands-on advice on building RAG applications with an open-source Milvus database deployed as a docker container. We will also introduce the integration of Milvus with Snowpark Container Services.
Encryption in Microsoft 365 - ExpertsLive Netherlands 2024
In this session I delve into the encryption technology used in Microsoft 365 and Microsoft Purview. Including the concepts of Customer Key and Double Key Encryption.
GraphSummit Singapore | The Future of Agility: Supercharging Digital Transfor...
Leonard Jayamohan, Partner & Generative AI Lead, Deloitte
This keynote will reveal how Deloitte leverages Neo4j’s graph power for groundbreaking digital twin solutions, achieving a staggering 100x performance boost. Discover the essential role knowledge graphs play in successful generative AI implementations. Plus, get an exclusive look at an innovative Neo4j + Generative AI solution Deloitte is developing in-house.
GraphSummit Singapore | Enhancing Changi Airport Group's Passenger Experience...
Dr. Sean Tan, Head of Data Science, Changi Airport Group
Discover how Changi Airport Group (CAG) leverages graph technologies and generative AI to revolutionize their search capabilities. This session delves into the unique search needs of CAG’s diverse passengers and customers, showcasing how graph data structures enhance the accuracy and relevance of AI-generated search results, mitigating the risk of “hallucinations” and improving the overall customer journey.
Mind map of terminologies used in context of Generative AI
Mind map of common terms used in context of Generative AI.
Video Streaming: Then, Now, and in the Future
In his public lecture, Christian Timmerer provides insights into the fascinating history of video streaming, starting from its humble beginnings before YouTube to the groundbreaking technologies that now dominate platforms like Netflix and ORF ON. Timmerer also presents provocative contributions of his own that have significantly influenced the industry. He concludes by looking at future challenges and invites the audience to join in a discussion.
Communications Mining Series - Zero to Hero - Session 1
This session provides introduction to UiPath Communication Mining, importance and platform overview. You will acquire a good understand of the phases in Communication Mining as we go over the platform with you. Topics covered:
• Communication Mining Overview
• Why is it important?
• How can it help today’s business and the benefits
• Phases in Communication Mining
• Demo on Platform overview
• Q/A
20 Comprehensive Checklist of Designing and Developing a Website
Dive into the world of Website Designing and Developing with Pixlogix! Looking to create a stunning online presence? Look no further! Our comprehensive checklist covers everything you need to know to craft a website that stands out. From user-friendly design to seamless functionality, we've got you covered. Don't miss out on this invaluable resource! Check out our checklist now at Pixlogix and start your journey towards a captivating online presence today.
Introducing Milvus Lite: Easy-to-Install, Easy-to-Use vector database for you...
Join us to introduce Milvus Lite, a vector database that can run on notebooks and laptops, share the same API with Milvus, and integrate with every popular GenAI framework. This webinar is perfect for developers seeking easy-to-use, well-integrated vector databases for their GenAI apps.
Essentials of Automations: The Art of Triggers and Actions in FME
In this second installment of our Essentials of Automations webinar series, we’ll explore the landscape of triggers and actions, guiding you through the nuances of authoring and adapting workspaces for seamless automations. Gain an understanding of the full spectrum of triggers and actions available in FME, empowering you to enhance your workspaces for efficient automation.
We’ll kick things off by showcasing the most commonly used event-based triggers, introducing you to various automation workflows like manual triggers, schedules, directory watchers, and more. Plus, see how these elements play out in real scenarios.
Whether you’re tweaking your current setup or building from the ground up, this session will arm you with the tools and insights needed to transform your FME usage into a powerhouse of productivity. Join us to discover effective strategies that simplify complex processes, enhancing your productivity and transforming your data management practices with FME. Let’s turn complexity into clarity and make your workspaces work wonders!
Presentation of the OECD Artificial Intelligence Review of Germany
Consult the full report at https://www.oecd.org/digital/oecd-artificial-intelligence-review-of-germany-609808d6-en.htm
Uni Systems Copilot event_05062024_C.Vlachos.pdf
Unlocking Productivity: Leveraging the Potential of Copilot in Microsoft 365, a presentation by Christoforos Vlachos, Senior Solutions Manager – Modern Workplace, Uni Systems
UiPath Test Automation using UiPath Test Suite series, part 5
Welcome to UiPath Test Automation using UiPath Test Suite series part 5. In this session, we will cover CI/CD with devops.
Topics covered:
CI/CD with in UiPath
End-to-end overview of CI/CD pipeline with Azure devops
Speaker:
Lyndsey Byblow, Test Suite Sales Engineer @ UiPath, Inc.
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...Edge AI and Vision Alliance
For the full video of this presentation, please visit: https://www.edge-ai-vision.com/2024/06/building-and-scaling-ai-applications-with-the-nx-ai-manager-a-presentation-from-network-optix/
Robin van Emden, Senior Director of Data Science at Network Optix, presents the “Building and Scaling AI Applications with the Nx AI Manager,” tutorial at the May 2024 Embedded Vision Summit.
In this presentation, van Emden covers the basics of scaling edge AI solutions using the Nx tool kit. He emphasizes the process of developing AI models and deploying them globally. He also showcases the conversion of AI models and the creation of effective edge AI pipelines, with a focus on pre-processing, model conversion, selecting the appropriate inference engine for the target hardware and post-processing.
van Emden shows how Nx can simplify the developer’s life and facilitate a rapid transition from concept to production-ready applications.He provides valuable insights into developing scalable and efficient edge AI solutions, with a strong focus on practical implementation.How to Get CNIC Information System with Paksim Ga.pptx
Pakdata Cf is a groundbreaking system designed to streamline and facilitate access to CNIC information. This innovative platform leverages advanced technology to provide users with efficient and secure access to their CNIC details.
Recently uploaded (20)
Observability Concepts EVERY Developer Should Know -- DeveloperWeek Europe.pdf
Observability Concepts EVERY Developer Should Know -- DeveloperWeek Europe.pdf
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...
Building RAG with self-deployed Milvus vector database and Snowpark Container...
Building RAG with self-deployed Milvus vector database and Snowpark Container...
Encryption in Microsoft 365 - ExpertsLive Netherlands 2024
Encryption in Microsoft 365 - ExpertsLive Netherlands 2024
GraphSummit Singapore | The Future of Agility: Supercharging Digital Transfor...
GraphSummit Singapore | The Future of Agility: Supercharging Digital Transfor...
GraphSummit Singapore | Enhancing Changi Airport Group's Passenger Experience...
GraphSummit Singapore | Enhancing Changi Airport Group's Passenger Experience...
Mind map of terminologies used in context of Generative AI
Mind map of terminologies used in context of Generative AI
Communications Mining Series - Zero to Hero - Session 1
Communications Mining Series - Zero to Hero - Session 1
20 Comprehensive Checklist of Designing and Developing a Website
20 Comprehensive Checklist of Designing and Developing a Website
Introducing Milvus Lite: Easy-to-Install, Easy-to-Use vector database for you...
Introducing Milvus Lite: Easy-to-Install, Easy-to-Use vector database for you...
Monitoring Java Application Security with JDK Tools and JFR Events
Monitoring Java Application Security with JDK Tools and JFR Events
Essentials of Automations: The Art of Triggers and Actions in FME
Essentials of Automations: The Art of Triggers and Actions in FME
Presentation of the OECD Artificial Intelligence Review of Germany
Presentation of the OECD Artificial Intelligence Review of Germany
UiPath Test Automation using UiPath Test Suite series, part 5
UiPath Test Automation using UiPath Test Suite series, part 5
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
“Building and Scaling AI Applications with the Nx AI Manager,” a Presentation...
How to Get CNIC Information System with Paksim Ga.pptx
How to Get CNIC Information System with Paksim Ga.pptx
Groschopp 05150 specsheet
- 1. Prepared by: Groschopp.com 02/24/14 Motor: Voltage: Speed: Gearbox: AC 1 Ph 6540 TENV 230 v 50 Hz 1220 rpm 4 Poles None Product ID: 5150 SPECIFICATIONS Rating: Speed: Torque: Current: Output: Output: 1215.2 rpm 0.8lb-in 0.23 amps 11 watts 0.0151 HP Breakdown (Cold): Speed: Torque: 786.42 rpm 1.17 lb-in Pullup (Cold): Speed: Torque: 0.0 rpm 0.97lb-in Duty Cycle: On: Off: Continuous Efficiency: Gearbox: Motor: System: 26.2 % 26.2 % Start/Stall Conditions: Current: Torque: 0.30 amps 0.97 lb-in Torque (lb-in) Speed RPM Efficiency 150 0 0.0 0.1 300 0.2 450 0.4 600 0.5 750 0.6 900 0.7 1050 0.8 1200 1.0 1350 1.1 90.0 80.0 70.0 60.0 50.0 40.0 30.0 20.0 10.0 Speed, Efficiency Vs. Torque Cold Hot Notes: Capacitor - 2.5uF 440V Sold & Serviced By: ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com