Concept of Particles and Free Body Diagram
Why FBD diagrams are used during the analysis?
It enables us to check the body for equilibrium.
By considering the FBD, we can clearly define the exact system of forces which we must use in the investigation of any constrained body.
It helps to identify the forces and ensures the correct use of equation of equilibrium.
Note:
Reactions on two contacting bodies are equal and opposite on account of Newton's III Law.
The type of reactions produced depends on the nature of contact between the bodies as well as that of the surfaces.
Sometimes it is necessary to consider internal free bodies such that the contacting surfaces lie within the given body. Such a free body needs to be analyzed when the body is deformable.
Physical Meaning of Equilibrium and its essence in Structural Application
The state of rest (in appropriate inertial frame) of a system particles and/or rigid bodies is called equilibrium.
A particle is said to be in equilibrium if it is in rest. A rigid body is said to be in equilibrium if the constituent particles contained on it are in equilibrium.
The rigid body in equilibrium means the body is stable.
Equilibrium means net force and net moment acting on the body is zero.
Essence in Structural Engineering
To find the unknown parameters such as reaction forces and moments induced by the body.
In Structural Engineering, the major problem is to identify the external reactions, internal forces and stresses on the body which are produced during the loading. For the identification of such parameters, we should assume a body in equilibrium. This assumption provides the necessary equations to determine the unknown parameters.
For the equilibrium body, the number of unknown parameters must be equal to number of available parameters provided by static equilibrium condition.
2. • Statics will build upon what you were
supposed to learn in your basic
physics and mathematics courses.
• We will talk about forces – vector
forces – about moments and torques,
reactions and the requirements of
static equilibrium of a particle or a
rigid body.
WHY Statics?
3. • You have seen a good bit of the basic
stuff of this course before, but we will
not assume you know the way to talk
about, or work with, these concepts,
principles, and methods so
fundamental to our subject.
• So we will recast the basics in our own
language, the language of engineering
mechanics.
WHY Statics?
4. • Think of this course as a language text; of
yourself as a language student beginning
the study of Engineering Mechanics
(Statics).
• You must learn the language if you aspire
to be an engineer.
• But this is a difficult language to learn,
unlike any other foreign language you have
learned.
WHY Statics?
5. • It is difficult because, on the surface, it
appears to be a language you already know.
But you will have to be on guard, careful,
not to presume the word you have heard
before bears the same meaning.
Words and phrases you have already used
now take on a more special and, in most
cases, narrower meaning; a couple of forces
is more than just two forces.
WHY Statics?
6. • The best way to learn a new language is
to use it – speak it, read it, listen to it on
audio tapes, watch it on television; better
yet, go to the land where it is the language
in use and use it to buy a loaf of bread, get
a hotel room for the night, ask to find the
nearest post office.
WHY Statics?
7. • So too in statics, we insist you begin to
use the language. Doing problems and
exercises, taking quizzes and the final, is
using the language.
• Statics course contains exercises
explained, as well as exercises for you to
tackle such as homeworks...
WHY Statics?
8. Chapter Outline
• Mechanics (an introduction)
• Fundamental Concepts (Newton’s Laws
of Motion)
• The International System of Units
(principles for applying the SI)
• Units of Measurement
• Numerical Calculations (procedures for
performing numerical calculations)
• General Procedure for Analysis (solving
problems)
9. Mechanics
• Mechanics can be divided into 2 branches:
1- Rigid-body Mechanics
2- Deformable-body Mechanics
- Solid bodies
- Fluids (liquids and gases
• Rigid-body Mechanics deals with
- Statics
- Dynamics
13. Force
– “push” or “pull” exerted by one body on another
– Occur due to direct contact between bodies
Eg: Person pushing against the wall
– Occur through a distance without direct contact
Eg: Gravitational, electrical and magnetic forces
Fundamentals Concepts
14. Fundamentals Concepts
• Particles
– Consider mass but neglect size
Eg: Size of Earth insignificant compared to its
size of orbit
• Rigid Body
– Combination of large number of particles
– Neglect material properties
Eg: Deformations in structures, machines and
mechanism
15. Fundamentals Concepts
• Concentrated Force
– Effect of loading, assumed to act at a point on
a body
– Represented by a concentrated force,
provided loading area is small compared to
overall size
Eg: Contact force between
wheel and ground
16. Fundamentals Concepts
Newton’s Three Laws of Motion
• First Law
“A particle originally at rest, or moving in a
straight line with constant velocity, will remain in
this state provided that the particle is not
subjected to an unbalanced
force”
First Law:
ΣF = 0
17. Fundamentals Concepts
Newton’s Three Laws of Motion
• Second Law
“A particle acted upon by an unbalanced force F
experiences an acceleration ‘a’ that has the
same direction as the force and a magnitude that
is directly proportional to the
force”
Second Law:
ΣF =
18. Fundamentals Concepts
Newton’s Three Laws of Motion
• Third Law
“The mutual forces of action and reaction
between two particles are equal and opposite
and collinear”
Third law:
Faction= Freaction
19. Fundamentals Concepts
WEIGHT
• m is the mass (kg)
• g is the acceleration due to gravity
(m/s2
)
• Most engineering calculations, g
at sea level and at a latitude of 45°
is enough. g=9.81 m/s2
W mg=
20. Fundamentals Concepts
• At the standard location,
g = 9.806 65 m/s2
• For calculations, we use
g = 9.81 m/s2
• Thus,
W = mg (g = 9.81m/s2
)
• Hence, a body of mass 1 kg has a weight
of 9.81 N, a 2 kg body weighs 19.62 N
21. Units of Measurement
Basic Quantities
• Length
– Locate position and describe size of physical
system
– Define distance and geometric properties of a
body
22. Units of Measurement
Basic Quantities
• Mass
– Comparison of action of one body against
another
– Measure of resistance of matter to a change in
velocity
24. Units of Measurement
SI Units
• Système International d’Unités
• F = ma is maintained only if
– Three of the units, called basic units, are
arbitrarily defined
– Fourth unit is derived from the equation
• SI units specifies:
length in meters (m),
time in seconds (s) and
mass in kilograms (kg)
• Unit of force, called Newton (N) is derived from
F = ma
26. The International
System of Units
Prefixes
• For a very large or very small numerical
quantity, the units can be modified by
using a prefix
• Each represent a multiple or sub-multiple
of a unit
Eg: 4 000 000 N = 4 000 kN (kilo-Newton)
= 4 MN (Mega- Newton)
0.005 m = 5 mm (milli-meter)
27. International System
of Units
Exponential
Form
Prefix SI
Symbol
Multiple
1 000 000 000 109
Giga G
1 000 000 106
Mega M
1 000 103
Kilo k
Sub-Multiple
0.001 10-3
Milli m
0.000 001 10-6
Micro μ
0.000 000 001 10-9
nano n
28. International System
of Units
Rules for Use
• Never write a symbol with a plural “s”.
Easily confused with second (s)
• Symbols are always written in lowercase
letters, except the 2 largest prefixes, mega
(M) and giga (G)
• Symbols named after an individual are
capitalized Eg: Newton (N)
29. International System
of Units
Rules for Use
• Quantities defined by several units which
are multiples, are separated by a dot
Eg: N = kg.m/s2
= kg.m.s-2
• The exponential power represented for a
unit having a prefix refer to both the unit
and its prefix
Eg: μN2
= (μN)2
= μN. μN
30. • If a derived unit is obtained by dividing a basic unit
to an other basic unit, the prefix should always be
used for the unit at the numerator and never for the
unit at the denominator.
• Ex: If under 100 N load, a spring elongates 20 mm,
the elongation constant ‘k’ of the spring is:
�=(100 N)/(20 mm)=(100 N)/(0.02 m) = 5000 N/m
or = 5 kN/m
Never k = 5 N/mm
International System
of Units
31. International System
of Units
Rules for Use
• Physical constants with several digits on
either side should be written with a space
between 3 digits rather than a comma (,)
Eg: 73 569.213 427
32. Numerical
Calculations
Significant Figures
- The accuracy of a number is specified by the
number of significant figures it contains.
- A significant figure is any digit including even
zero. The location of the decimal point of a
number is not important
Eg: 5 604 and 34.52 both have four significant
numbers
33. Numerical
Calculations
Significant Figures
- When numbers begin or end with zero, we make
use of prefixes to clarify the number of significant
figures
Eg: 400 → as 1 significant figure would be 0.4 (103
)
or 4 (102
)
2 500 → as 3 significant figures would be 2.50 (103
)
34. Numerical
Calculations
Rounding Off Numbers
For numerical calculations, the accuracy
obtained from the solution of a problem
would never be better than the accuracy of
the problem data!
Often handheld calculators or computers
involve more figures in the answer than the
number of significant figures in the data.
36. Numerical
Calculations
To ensure the accuracy of the final results,
always give your answers 3 digits after the
decimal point.
Eg: 45.703
101.007
1 398.400
37. Numerical
Calculations
For plane angles used in trigonometry, in this
course, please give your answers in 4 digits
after the decimal point both for the angles and
their trigonometric equivalencies.
Eg: Sin 35.0000˚
= 0.5736
Cos 45.0380˚
= 0.7066
Tan-1
1.3459 = 53.3878˚
38. General Procedure
for Analysis
• Most efficient way of learning is to
solve problems:
• To be successful at this, it is important to present
the work in a logical and orderly way as
suggested:
1) Read the problem carefully and try to correlate
actual physical situation with theory;
2) Draw any necessary diagrams and tabulate
the problem data;
39. General Procedure
for Analysis
3) Apply relevant principles, generally in
mathematical forms;
4) Solve the necessary equations, algebraically
as far as practical, making sure that they are
dimensionally homogenous, using a consistent
set of units and complete the solution
numerically;
40. General Procedure
for Analysis
5) Report the answer with no more significance
figures than accuracy of the given data;
6) Study the answer with technical judgment and
common sense to determine whether or not it
seems reasonable.