Prosedur recovery password pada switch meliputi dua metode berdasarkan apakah fitur recovery password diaktifkan atau tidak. Jika diaktifkan, prosesnya meliputi inisialisasi flash system, memanggil file helper, mengganti nama file konfigurasi, dan mengubah password. Jika dinonaktifkan, pengguna perlu menyetujui reset konfigurasi sebelum mengikuti langkah serupa untuk mengubah password.
2 KISI-KISI Ujian Sekolah Dasar mata pelajaranPPKn 2024.pdf
Recovery password pada switch
1. Recovery Password pada switch
1. Hubungkan PC dengan software terminal-emulation (ex: Hyper Terminal) ke port
console switch.
2. Seting line speed pada software emulation ke baud 9600.
3. Matikan switch. Hubungkan kembali kabel power ke switch dan, dalam 15 detik tekan
tombol Mode selama LED System yang berwarna hijau berkedip. Terus tekan tombol
Mode sampai LED System berubah warna hijau kekuningan Kemudian hijau terang;
kemudian lepaskan tombol Mode.
Beberapa baris informasi instruksi tampil, memberitahukan jika prosedur recovery
password telah dinontaktifkan atau tidak. Jika melihat informasi seperti :
The system has been interrupted prior to initializing the
flash file system.
The following commands will initialize the flash file
system
Lanjutkan proses pada bagian “Prosedur dengan Recovery Password
diaktifkan”, ikuti langkah-langkah yang ditunjukkan.
Jika pesan yang tampil :
The password-recovery mechanism has been triggered, but is
currently disabled.
Lanjutkan proses pada bagian “Prosedur dengan Recovery Password
dinontaktifkan”, dan ikuti langkah-langkah yang ditunjukkan.
4. Setelah password di recovery, reload switch dengan :
Switch> reload
Proceed with reload? [confirm] y
Prosedur dengan Recovery Password diaktifkan
Jika mekanisme password-recovery diaktifkan, pesan berikut akan tampil:
The system has been interrupted prior to initializing the flash
file system.
The following commands will initialize the flash file system,
and finish loading the operating system software:
2. flash_init
load_helper
boot
Langkah 1. Inisialisasi system file flash:
Switch: flash_init
Langkah 2. Jika kita telah menseting speed port console selain 9600. Ubah line speed
software emulation sesuai dengan port console switch.
Langkah 3. Panggil file-file helper:
Switch: load_helper
Langkah 4. Tampilkan isi dari memory flash:
Switch: dir flash:
Sistem file switch menampilkan :
Directory of flash:
13 drwx 192 Mar 01 1993 22:30:48 c2960-lanbasemz.
122-25.FX
11 -rwx 5825 Mar 01 1993 22:31:59 config.text
18 -rwx 720 Mar 01 1993 02:21:30 vlan.dat
16128000 bytes total (10003456 bytes free)
Langkah 5. Ubah file konfigurasi menjadi config.text.old
File ini berisi pendefinisian password.
Switch: rename flash:config.text flash:config.text.old
Langkah 6. Boot system :
Switch: boot
Kita akan ditanya untuk memulai program setup. Pada prompt berikan jawaban N.
Continue with the configuration dialog? [yes/no]: N
Langkah 7. Pada promt switch, masuk ke mode privilege EXEC:
Switch> enable
Langkah 8. Ubah file konfigurasi ke nama aslinya:
3. Switch# rename flash:config.text.old flash:config.text
Langkah 9. Salin file konfigurasi ke memory:
Switch# copy flash:config.text system:running-config
Source filename [config.text]?
Destination filename [running-config]?
Tekan tombol enter untuk merespon prompt konfirmasi.
File konfigurasi akan dipanggil kembali, dan kita sudah bisa mengubah password
Langkah 10. Masuk ke modus konfigurasi global:
Switch# configure terminal
Langkah 11. Ubah password :
Switch (config)# enable secret password
Secret password bisa 1 sampai 25 karakter alpanumerik, bisa dimulai dengan sebuah
nomor, bersifat case sensitive.
Langkah 12. Kembali ke modul privilege EXEC:
Switch (config)# exit
Switch#
Langkah 13. Simpan running configuration ke file startup configuration:
Switch# copy running-config startup-config
Prosedur dengan Recovery Password dinontaktifkan
Jika mekanisme password-recovery dinonaktifkan, akan tampil pesan berikut:
The password-recovery mechanism has been triggered, but is
currently disabled. Access to the boot loader prompt through the
password-recovery mechanism is disallowed at this point.
However, if you agree to let the system be reset back to the
default system configuration, access to the boot loader prompt
can still be allowed.
Would you like to reset the system back to the default
configuration (y/n)?
Jika kita jawab dengan n(no), proses boot normal akan dilanjutkan; dan kita tidak bisa
mengakses prompt boot loader, akan tampil pesan berikut :
4. Press Enter to continue........
Namun, jika kita jawab y(yes), file konfigurasi pada memory flash dan file database
VLAN akan terhapus. Ketika konfigurasi default dipanggil, kita bisa menset ulang
password.
Langkah 1. Pilih untuk lanjut dengan password recivey dan kehilangan konfigurasi yang
ada:
Would you like to reset the system back to the default
configuration (y/n)? Y
Langkah 2. Panggil file-file helper:
Switch: load_helper
Langkah 3. Tampilkan isi memory flash:
switch: dir flash:
File system switch menampilkan:
Directory of flash:
13 drwx 192 Mar 01 1993 22:30:48 c2960-lanbasemz.122-25.FX.0
16128000 bytes total (10003456 bytes free)
Langkah 4. Boot system:
Switch: boot
Kita akan diminta untuk memulai program setup. Untuk melanjutkan dengan password
recovery, berikan jawaban N pada prompt.
Continue with the configuration dialog? [yes/no]: N
Langkah 5. Pada prompt switch, masuk ke modus privilege:
Switch> enable
Langkah 6. Masuk ke modus konfigurasi global:
Switch# configure terminal
Langkah 7. Ubah password:
Switch (config)# enable secret password
5. Secret password bisa terdiri atas 1 sampai 25 karakter alpanumerik, bisa dimulai
dengan nomor, bersifat case sensitive.
Langkah 8. Kembali ke modul privilege EXEC:
Switch (config)# exit
Switch#
Langkah 9. Salin running configuration ke file startup configuration;
Switch# copy running-config startup-config