Teks tersebut membahas tentang pengujian sumur minyak yang meliputi definisi dan fungsi well testing, metode manual dan otomatis well testing, komponen well testing seperti test header, test line, test tank, test separator, serta cara menghitung hasil produksi sumur berdasarkan data yang diperoleh dari well testing seperti BFPD, BS&W, BWPD, dan BOPD. Juga dijelaskan tahapan persiapan dan pelaksanaan well testing mulai dari memeriksa peralatan hingga mem
Dokumen tersebut membahas tentang produksi packer untuk penyelesaian sumur, termasuk overview produksi packer, komponen utama, cara penyiapan dan penggunaannya, cara pengaturan dan pelepasannya, serta penyebab kegagalan. Produksi packer digunakan untuk menyekat atau memisahkan annulus antara rangkaian tubing dan casing produksi, dan dibagi menjadi tiga jenis berdasarkan cara pengaturannya.
This document discusses squeeze cementing techniques and considerations. Squeeze cementing involves pumping cement slurry under pressure against a permeable formation to create a cement seal. Key aspects covered include reasons for squeeze cementing, slurry design factors like viscosity and fluid loss control, laboratory testing methods, and primary concerns like establishing an injection rate and avoiding formation fracture. Detailed explanations are provided for methods like running squeezes through packers or cement retainers and different injection techniques.
Teks tersebut membahas tentang pengujian sumur minyak yang meliputi definisi dan fungsi well testing, metode manual dan otomatis well testing, komponen well testing seperti test header, test line, test tank, test separator, serta cara menghitung hasil produksi sumur berdasarkan data yang diperoleh dari well testing seperti BFPD, BS&W, BWPD, dan BOPD. Juga dijelaskan tahapan persiapan dan pelaksanaan well testing mulai dari memeriksa peralatan hingga mem
Dokumen tersebut membahas tentang produksi packer untuk penyelesaian sumur, termasuk overview produksi packer, komponen utama, cara penyiapan dan penggunaannya, cara pengaturan dan pelepasannya, serta penyebab kegagalan. Produksi packer digunakan untuk menyekat atau memisahkan annulus antara rangkaian tubing dan casing produksi, dan dibagi menjadi tiga jenis berdasarkan cara pengaturannya.
This document discusses squeeze cementing techniques and considerations. Squeeze cementing involves pumping cement slurry under pressure against a permeable formation to create a cement seal. Key aspects covered include reasons for squeeze cementing, slurry design factors like viscosity and fluid loss control, laboratory testing methods, and primary concerns like establishing an injection rate and avoiding formation fracture. Detailed explanations are provided for methods like running squeezes through packers or cement retainers and different injection techniques.
This document provides an introduction to hydraulic workover and snubbing solutions. It discusses the history of hydraulic workover which has been used since the 1920s. It defines snubbing as running and pulling tubulars with surface pressure present. It outlines the benefits of hydraulic workover such as remaining in production and completing work without killing the well. It also describes potential applications like fishing, drilling, completions, and abandonment. Finally, it explains the mechanics of hydraulic workovers including the use of traveling and stationary slips to move tubulars through blowout preventer rams.
Dokumen tersebut membahas tentang perencanaan sumur gas lift, meliputi penentuan titik injeksi gas, jumlah gas yang diinjeksikan, spasi valve, dan tekanan setting valve. Langkah-langkah perencanaan mencakup plot kurva tekanan, penentuan gradient cairan dan gas, serta perhitungan berbagai parameter seperti produksi, GLR, dan tekanan.
This document discusses cementation jobs in oil and gas wells. It begins by explaining the objective of cementing wells, which is to isolate zones and support the casing. It then describes how cementing works, including preparing the cement slurry, pumping it down the casing using plugs, and allowing it to harden. The document discusses primary cementing techniques like single-stage and multi-stage cementing. It also covers API cement classifications and discusses the use of additives like accelerators, retarders, and fluid loss additives. In summary, the document provides an overview of the cementing process and various techniques used to isolate zones and support casing in oil and gas wells.
Dokumen tersebut membahas tentang pengertian dasar Workover dan Wellservices serta peralatan yang digunakan oleh Elnusa dalam melakukan pekerjaan tersebut seperti Hydraulic Workover Unit, Cementing & Pumping Unit, Coil Tubing Unit, dan Slickline Unit."
This presentation is a course a bout wellheads which includes the basic components of the well head and the advanced techniques.
helping students who are cared about petroleum industry to increase their knowledge about this tool that is important for both drilling and production.
For Further information, use the following LinkedIn account:
https://www.linkedin.com/in/mohamed-abdelshafy-abozeima-9b7589119/
1. Open-hole completions, also called 'barefoot' completions, involve setting casing above the productive interval and drilling into and through the reservoir, leaving it uncased and exposed to the wellbore.
2. For a simple open-hole well completion, the process involves setting production casing above the zone of interest before drilling into it, leaving it open to the wellbore, and then installing wellhead equipment to control flow.
3. Key steps include drilling into the formation, installing wellhead valves and pipes to direct and burn off initial flow, and cleaning the well until the flow stabilizes before testing and starting production.
After drilling is completed, wells undergo completion procedures to prepare them for production. This involves setting production casing and cementing it through the target zone. Tubing is run inside the casing with a packer to isolate the production zone. A Christmas tree is installed to control flow. Completion types include open hole, liners, and perforated casing. Perforating creates holes through casing into the formation. Some formations require stimulation like acidizing to improve permeability or fracturing to create conductive fractures held open by proppant. This increases flow into the wellbore.
01. drilling rig sistem tenaga power system okrusihan
Sistem tenaga pada rig pemboran terdiri dari dua komponen utama yaitu power supply equipment dan distribution equipment. Power supply equipment menghasilkan tenaga melalui prime mover seperti mesin diesel. Tenaga kemudian didistribusikan ke peralatan bor melalui transmisi mekanis menggunakan sprocket dan rantai atau transmisi listrik menggunakan kabel. Sistem ini penting untuk mendukung seluruh operasi pemboran.
Wellhead equipment Introduction Based on API 6a & NACEAmir Rafati
1. Typical Onshore Wellhead and Casing Head Types
• CSG HEAD NO.1
• CSG HEAD NO.3
• CSG HEAD NO.6
• CSG HEAD NO.8
• CSG HEAD NO.9
• CSG HEAD DESIGN DUE TO FIELD EXPERIENCES
• AG(H)-10K
• B(H)-10K
• C(H)-5K
• V(H)-5K
• T(H)-3K,5K
• WELLHEAD DESIGN DUE TO FIELD EXPERIENCES
2. Brief Description of Wellhead Equipment and their Types
• Sealings and Ring Gaskets
• Safety valves
• Gate valves
• Double Studded Adaptors
• Spools
• Hangers
• Flanges
3. Install and Testing Wellhead and Casing Head Equipment
• Safety valves
• Gate valves
• Double Studded Adaptors
• Spools
• Hangers
• Flanges
4. Introduction to API 6A applications
• PSL: PRODUCT SPECIFICATION LEVELS
• PR: PERFORMANCE REQUIREMENT
• T/C: TEMPERATURE CLASS
• M/C: MATERIAL CLASS
Laporan ini membahas tentang praktikum analisis semen pemboran yang meliputi pembuatan suspensi semen dan cetakan sampel, pengujian densitas, rheologi, thickening time, free water, filtration loss, compressive strength, shear bond strength, dan luas permukaan bubuk semen. Hasil pengujian digunakan untuk mengetahui kualitas semen yang akan digunakan dalam konstruksi sumur minyak dan gas.
BAB II membahas kegiatan-kegiatan yang dilakukan sebelum operasi pengeboran, meliputi persiapan jalan ke lokasi pengeboran, persiapan lokasi pengeboran seperti meratakan lokasi, membuat kolam cadangan dan cellar, serta persiapan air dan peralatan pengeboran. Kegiatan terakhir adalah transportasi peralatan ke lokasi dan pendirian menara pengeboran."
Primary cementing involves pumping a cement slurry down the casing or drill pipe to isolate formations and support the casing. It is critical to well integrity. Some key points covered in the document include:
- Cementing is done after lowering casing to isolate formations and support the casing.
- Primary cementing techniques can include single-stage, multi-stage, or liner cementation depending on well conditions.
- Secondary cementing techniques like squeeze cementing are used to remedy issues with prior cement jobs or isolate specific formations.
- Cementing is a critical operation that requires careful planning and execution to achieve well integrity on the first attempt, as there are no second chances.
Dokumen tersebut memberikan informasi mengenai persiapan peralatan untuk kegiatan pemboran minyak dan gas, termasuk sistem pengangkat, sistem pemutar, sistem sirkulasi, sistem daya, dan sistem pencegah semburan liar. Dijelaskan pula fungsi dan jenis-jenis peralatan utama yang digunakan dalam kegiatan pemboran seperti derrick, rig, block and tackle, drawwork, bit, dan blowout preventer system.
Formation damage can occur through physical, chemical, and bacterial mechanisms. The formation damage process involves filter cake formation and drilling mud formulation. Formation damage sources include drilling, completion, workover, stimulation, production, and injection operations. Common damage mechanisms are particle invasion, clay swelling/dispersion, scale precipitation, and fines migration. Remedial measures include acidizing, fracturing, clay stabilization, and surfactant treatments. Proper mud system design aims to minimize invasion and filtrate loss into the formation.
Modul ini membahas sistem instrumentasi untuk operator pengendali pabrik, mencakup drawing dan sistem udara instrument, sistem pengukuran variabel proses seperti tekanan dan temperatur, control valve, sistem pengendalian proses, dan metode tuning controller. Tujuannya adalah meningkatkan pemahaman operator tentang alat ukur dan sistem kontrol yang digunakan dalam proses produksi.
This document provides an introduction to hydraulic workover and snubbing solutions. It discusses the history of hydraulic workover which has been used since the 1920s. It defines snubbing as running and pulling tubulars with surface pressure present. It outlines the benefits of hydraulic workover such as remaining in production and completing work without killing the well. It also describes potential applications like fishing, drilling, completions, and abandonment. Finally, it explains the mechanics of hydraulic workovers including the use of traveling and stationary slips to move tubulars through blowout preventer rams.
Dokumen tersebut membahas tentang perencanaan sumur gas lift, meliputi penentuan titik injeksi gas, jumlah gas yang diinjeksikan, spasi valve, dan tekanan setting valve. Langkah-langkah perencanaan mencakup plot kurva tekanan, penentuan gradient cairan dan gas, serta perhitungan berbagai parameter seperti produksi, GLR, dan tekanan.
This document discusses cementation jobs in oil and gas wells. It begins by explaining the objective of cementing wells, which is to isolate zones and support the casing. It then describes how cementing works, including preparing the cement slurry, pumping it down the casing using plugs, and allowing it to harden. The document discusses primary cementing techniques like single-stage and multi-stage cementing. It also covers API cement classifications and discusses the use of additives like accelerators, retarders, and fluid loss additives. In summary, the document provides an overview of the cementing process and various techniques used to isolate zones and support casing in oil and gas wells.
Dokumen tersebut membahas tentang pengertian dasar Workover dan Wellservices serta peralatan yang digunakan oleh Elnusa dalam melakukan pekerjaan tersebut seperti Hydraulic Workover Unit, Cementing & Pumping Unit, Coil Tubing Unit, dan Slickline Unit."
This presentation is a course a bout wellheads which includes the basic components of the well head and the advanced techniques.
helping students who are cared about petroleum industry to increase their knowledge about this tool that is important for both drilling and production.
For Further information, use the following LinkedIn account:
https://www.linkedin.com/in/mohamed-abdelshafy-abozeima-9b7589119/
1. Open-hole completions, also called 'barefoot' completions, involve setting casing above the productive interval and drilling into and through the reservoir, leaving it uncased and exposed to the wellbore.
2. For a simple open-hole well completion, the process involves setting production casing above the zone of interest before drilling into it, leaving it open to the wellbore, and then installing wellhead equipment to control flow.
3. Key steps include drilling into the formation, installing wellhead valves and pipes to direct and burn off initial flow, and cleaning the well until the flow stabilizes before testing and starting production.
After drilling is completed, wells undergo completion procedures to prepare them for production. This involves setting production casing and cementing it through the target zone. Tubing is run inside the casing with a packer to isolate the production zone. A Christmas tree is installed to control flow. Completion types include open hole, liners, and perforated casing. Perforating creates holes through casing into the formation. Some formations require stimulation like acidizing to improve permeability or fracturing to create conductive fractures held open by proppant. This increases flow into the wellbore.
01. drilling rig sistem tenaga power system okrusihan
Sistem tenaga pada rig pemboran terdiri dari dua komponen utama yaitu power supply equipment dan distribution equipment. Power supply equipment menghasilkan tenaga melalui prime mover seperti mesin diesel. Tenaga kemudian didistribusikan ke peralatan bor melalui transmisi mekanis menggunakan sprocket dan rantai atau transmisi listrik menggunakan kabel. Sistem ini penting untuk mendukung seluruh operasi pemboran.
Wellhead equipment Introduction Based on API 6a & NACEAmir Rafati
1. Typical Onshore Wellhead and Casing Head Types
• CSG HEAD NO.1
• CSG HEAD NO.3
• CSG HEAD NO.6
• CSG HEAD NO.8
• CSG HEAD NO.9
• CSG HEAD DESIGN DUE TO FIELD EXPERIENCES
• AG(H)-10K
• B(H)-10K
• C(H)-5K
• V(H)-5K
• T(H)-3K,5K
• WELLHEAD DESIGN DUE TO FIELD EXPERIENCES
2. Brief Description of Wellhead Equipment and their Types
• Sealings and Ring Gaskets
• Safety valves
• Gate valves
• Double Studded Adaptors
• Spools
• Hangers
• Flanges
3. Install and Testing Wellhead and Casing Head Equipment
• Safety valves
• Gate valves
• Double Studded Adaptors
• Spools
• Hangers
• Flanges
4. Introduction to API 6A applications
• PSL: PRODUCT SPECIFICATION LEVELS
• PR: PERFORMANCE REQUIREMENT
• T/C: TEMPERATURE CLASS
• M/C: MATERIAL CLASS
Laporan ini membahas tentang praktikum analisis semen pemboran yang meliputi pembuatan suspensi semen dan cetakan sampel, pengujian densitas, rheologi, thickening time, free water, filtration loss, compressive strength, shear bond strength, dan luas permukaan bubuk semen. Hasil pengujian digunakan untuk mengetahui kualitas semen yang akan digunakan dalam konstruksi sumur minyak dan gas.
BAB II membahas kegiatan-kegiatan yang dilakukan sebelum operasi pengeboran, meliputi persiapan jalan ke lokasi pengeboran, persiapan lokasi pengeboran seperti meratakan lokasi, membuat kolam cadangan dan cellar, serta persiapan air dan peralatan pengeboran. Kegiatan terakhir adalah transportasi peralatan ke lokasi dan pendirian menara pengeboran."
Primary cementing involves pumping a cement slurry down the casing or drill pipe to isolate formations and support the casing. It is critical to well integrity. Some key points covered in the document include:
- Cementing is done after lowering casing to isolate formations and support the casing.
- Primary cementing techniques can include single-stage, multi-stage, or liner cementation depending on well conditions.
- Secondary cementing techniques like squeeze cementing are used to remedy issues with prior cement jobs or isolate specific formations.
- Cementing is a critical operation that requires careful planning and execution to achieve well integrity on the first attempt, as there are no second chances.
Dokumen tersebut memberikan informasi mengenai persiapan peralatan untuk kegiatan pemboran minyak dan gas, termasuk sistem pengangkat, sistem pemutar, sistem sirkulasi, sistem daya, dan sistem pencegah semburan liar. Dijelaskan pula fungsi dan jenis-jenis peralatan utama yang digunakan dalam kegiatan pemboran seperti derrick, rig, block and tackle, drawwork, bit, dan blowout preventer system.
Formation damage can occur through physical, chemical, and bacterial mechanisms. The formation damage process involves filter cake formation and drilling mud formulation. Formation damage sources include drilling, completion, workover, stimulation, production, and injection operations. Common damage mechanisms are particle invasion, clay swelling/dispersion, scale precipitation, and fines migration. Remedial measures include acidizing, fracturing, clay stabilization, and surfactant treatments. Proper mud system design aims to minimize invasion and filtrate loss into the formation.
Modul ini membahas sistem instrumentasi untuk operator pengendali pabrik, mencakup drawing dan sistem udara instrument, sistem pengukuran variabel proses seperti tekanan dan temperatur, control valve, sistem pengendalian proses, dan metode tuning controller. Tujuannya adalah meningkatkan pemahaman operator tentang alat ukur dan sistem kontrol yang digunakan dalam proses produksi.
Dokumen tersebut membahas tentang manajemen alat berat yang meliputi biaya kepemilikan (owning cost), biaya operasi (operating cost), contoh perhitungan biaya, dan penyusunan jadwal proyek pembangunan jalan yang mencakup tahapan clearing, stripping, spreading, dan pemampatan.
Mata kuliah ini membahas tentang alat berat yang mencakup prinsip kerja, komponen, jenis, pemecahan masalah, perbaikan dan perawatan. Mahasiswa diharapkan mampu menganalisis operasi alat berat. Materi mencakup hidrolik, sistem kerja, aplikasi, dan penilaian mahasiswa melalui tugas dan ujian.
Dokumen tersebut membahas tentang fasilitas produksi lepas pantai yang mencakup beberapa hal seperti: jenis-jenis anjungan produksi lepas pantai seperti steel jacket platform, concrete gravity platform, dan floating production storage and offloading (FPSO); fasilitas transportasi produksi; fasilitas pemisahan minyak dan gas seperti separator, scrubber gas, dan free water knockout tank; serta peralatan-peralatan pada anjungan kompresor seperti kompresor, scrubber gas, dan generator engine.
This document provides an overview of the oil and gas industry in Indonesia, covering topics such as:
1. The geological origins and formation processes of oil and gas, including both organic and abiogenic theories.
2. Reservoir types and characteristics, including different geological structures that can trap hydrocarbons, as well as reservoir drive mechanisms.
3. Exploration techniques such as aerial and satellite surveys, gravity and magnetic studies, 2D and 3D seismic acquisition and analysis, and well drilling.
4. Details of the drilling process and data acquisition methods like well logging.
It includes a table of contents outlining the various chapters and their subsections on these important oil and gas concepts and methods.
This document provides a preface and overview for a textbook on petroleum production engineering. It discusses how modern computer technologies have revolutionized the petroleum industry and motivated the authors to write this textbook. The textbook is intended to provide production engineers with guidelines for designing, analyzing, and optimizing petroleum production systems using computer-assisted approaches. It covers topics like well performance, artificial lift methods, and production enhancement techniques across 18 chapters in 4 parts. The preface provides details on the intended audience, topics covered, and goals of presenting engineering principles through examples and companion computer programs.
The document discusses oil and gas production and surface facilities. It begins with an introduction to the upstream, midstream, and downstream sectors of the oil and gas industry. It then covers well types at the production phase, including oil, gas, and water injection wells. It describes key wellhead components like the casing head, tubing head, Christmas tree, and safety control subsurface safety valve. It provides details on various artificial lift methods and their relative advantages and disadvantages. It concludes with descriptions of hook-up and flow line components used to transport oil and gas from wells.
This document summarizes a minor project report on subsurface safety valves. It discusses the history and operation of safety valves, which provide protection against uncontrolled flow from oil and gas wells. Safety valves have evolved from simple downhole devices in the 1940s to complex systems integral to offshore well completions worldwide. There are two main types - surface operated and subsurface operated valves. Surface operated valves are further divided into pressure differential and pressure operated types, while subsurface operated valves include wireline retrievable and tubing mounted varieties. The project aims to develop an understanding of safety valve applications and parameters that affect their performance and efficiency.
The Two Way Valve JDS-X is used to change the direction of material flow in pneumatic conveying systems. It is suitable for a wide range of materials and industries due to its compact design that requires little installation space. The stainless steel and cast iron construction makes it durable and low maintenance. Dimensions and technical specifications are provided for various models.
Dokumen tersebut menjelaskan ketentuan dan prosedur program Kerja Praktek dan Tugas Akhir mahasiswa di PT Chevron Pacific Indonesia. Beberapa poin pentingnya adalah permohonan harus diajukan minimal 3 bulan sebelumnya, lama KP maksimal 1 bulan dan TA 2 bulan, serta dokumen yang diperlukan antara lain surat pengantar dari fakultas, transkrip nilai, proposal, dan CV.
Teks tersebut menjelaskan proses pembentukan minyak bumi yang memerlukan waktu jutaan tahun, meliputi penguburan organisme laut di dasar laut, pembentukan batuan sedimen, migrasi hidrokarbon ke batuan reservoir, dan jebakan geologis. Proses ini melibatkan faktor temperatur dan tekanan bawah tanah selama jutaan tahun.
Dokumen tersebut membahas tentang reservoir minyak dan gas bumi. Ia menjelaskan bahwa reservoir terdiri atas batuan reservoir berpori yang mengandung minyak dan gas, dilindungi oleh lapisan penutup impermeabel. Reservoir harus memiliki batuan sumber yang menghasilkan minyak dan gas. Dokumen ini juga menjelaskan sifat-sifat reservoir seperti porositas, permeabilitas, saturasi, dan kebasahan yang mempengaruhi aliran fluida di reservoir.
Dokumen tersebut membahas tentang reservoir minyak dan gas bumi. Ia menjelaskan bahwa reservoir terdiri atas batuan reservoir berpori yang mengandung minyak dan gas, dilindungi oleh lapisan penutup impermeabel. Reservoir harus memiliki batuan sumber yang menghasilkan minyak dan gas. Dokumen ini juga menjelaskan sifat-sifat reservoir seperti porositas, permeabilitas, saturasi, dan kebasahan yang mempengaruhi aliran fluida di reservoir.
Dokumen tersebut membahas tentang reservoir minyak dan gas bumi. Ia menjelaskan bahwa reservoir terdiri atas batuan reservoir berpori yang mengandung minyak dan gas, dilindungi oleh lapisan penutup impermeabel. Reservoir harus memiliki batuan sumber yang menghasilkan minyak dan gas. Dokumen ini juga menjelaskan sifat-sifat reservoir seperti porositas, permeabilitas, saturasi, dan kebasahan yang mempengaruhi aliran fluida di reservoir.
Dokumen tersebut membahas sejarah pengeboran minyak di dunia dan Indonesia. Pada tahun 1859, Kolonel Drake melakukan pengeboran minyak pertama di Pennsylvania dan memperoleh hasil produksi 2000 barel minyak pada tahun pertama. Di Indonesia, pengeboran minyak pertama dilakukan oleh J. Reerink pada tahun 1871 di Majalengka, 12 tahun setelah pengeboran Kolonel Drake.
Buku panduan ini memberikan pengenalan dasar tentang bermain gitar, meliputi pengenalan komponen gitar, sistem jari dan nada, serta penjelasan awal tentang chord dasar. Tujuannya adalah membantu pemula mempelajari dasar-dasar bermain gitar secara mandiri dan efektif.
Banyak orang menganggap mempelajari kitab Wahyu adalah sulit. Selain karena membicarakan simbol-simbol yang tidak biasa, kitab Wahyu juga memiliki tema-tema yang kompleks. Nah, bagaimana cara terbaik membedah kitab Wahyu?
Mari kita pelajari bersama lebih dahulu 3 pasal pertama dari kitab ini dalam kelas diskusi "Bedah Kitab Wahyu" (BKW) pada 19—26 Juni 2024 melalui grup WA.
Sebelum kelas dimulai, ikuti lebih dahulu pemaparan materinya via Zoom pada:
Rabu, 19 Juni 2024.
- Pagi: pkl. 10.30—12.00 WIB
- Malam: pkl. 19.00—20.30 WIB
Daftarkan diri Anda segera di https://bit.ly/form-mlc.
Kontak:
WA: 0821-3313-3315 (MLC)
E-Mail: kusuma@in-christ.net
Modul Projek Kearifan Lokal - Warung Pasundan - Fase B (1).pdf
Wellhead hanger xmastree
1. BUKU PINTAR MIGAS INDONESIA
Wellhead, Hangers dan X-Mas Tree
Wellhead merupakan salah satu komponen penting dalam proses pengeboran selain semen
atau packer. Wellhead ini dipasang pada setiap akhir dari casing dan tubing string di
permukaan sumur. Di dalam kelompok wellhead, termasuk pula casing head, casing head
spool, tubing head spool, dan christmas tree.
Wellhead memiliki dua fungsi penting, yaitu :
1. Sebagai penyangga casing string
Setiap casing dan tubing yang dimasukkan ke dalam sumur secara fisik tergantung pada
wellhead.
2. Sebagai tempat terpasangnya alat pengontrol aliran
Wellhead dirancang untuk dapat dihubungkan dengan alat pengontrol aliran dari dan ke
dalam sumur. Pada tahap pengeboran, alat pengontrol aliran ini dikenal sebagai blow out
preventer stack atau BOP. BOP ini dipasang pada permukaan wellhead dan digunakan
terus hingga tubing masuk ke dalam sumur. Pada tahap completion, tugas BOP diganti
dengan sistem pengontrol aliran atau yang dikenal dengan nama Christmas Tree.
Ada empat tipe dasar dari wellhead, yaitu :
1. Wellhead Sistem Konvensional Spool
2. Wellhead Sistem Compact Spool
3. Wellhead Sistem Mud Line Suspension
4. Subsea Wellhead
1. Wellhead Sistem Konvensional Spool
Pada tipe ini, conductor atau surface string joint yang terakhir di-install ke casing head
dengan sambungan ulir untuk threaded connection atau sambungan las untuk welded
connection. Profil dalam casing head disiapkan untuk menyangga casing yang selanjutnya.
Untuk melengkapi proses ini, pada joint terakhir casing dipasang hanger dan didudukkan di
dalam casing head. Tipe hanger tersebut dikenal dengan nama slip hanger. Hanger jenis ini
hanya cocok untuk berat casing ringan dan menengah. Untuk hanger alternatif dapat
digunakan mandrel hanger dimana casing joint terakhir disambungkan ke hanger tersebut
melalui ulir yang telah tersedia.
Gambar 1.1 Wellhead Sistem
Konvensional Spool
Wellhead, Hangers dan X-Mas Tree
Gambar 1.2 Tubing Head Spool lengkap dengan
Christmas Tree
Halaman 1 dari 4
Kontributor : Johannes Julianto
2. BUKU PINTAR MIGAS INDONESIA
Untuk menyangga casing berikutnya, dipasang casing head spool diatas casing head. Casing
head spool ini memiliki profil dalam yang serupa dengan casing head. Akhirnya, untuk
menyangga production tubing string, digunakan spool yang dikenal dengan nama tubing head
spool dan dipasang diatas casing head spool. Setelah completion string terpasang, barulah
BOP dilepas kemudian dipasang Christmas tree.
2. Wellhead Sistem Compact Spool
Wellhead sistem compact spool biasanya dikenal juga dengan beberapa nama seperti
Unihead, Uni Wellhead atau Unitized Wellhead. Sistem ini adalah pengambangan dari sistem
konvensional spool dimana casing head spool dan tubing head spool terintegerasi menjadi
satu kesatuan. Sehingga sistem ini dapat menghemat waktu drilling dan meningkatkan
keamanan karena tidak perlu melepas BOP seperti yang terjadi pada sistem konvensional
dimana BOP harus dilepas pada setiap pemasangan casing head spool atau tubing head
spool. Untuk diketahui, dilepasnya BOP memiliki potensi yang membahayakan bagi
keamanan sumur, karena hidrokarbon dapat muncul ke permukaan dengan tekanan tinggi
secara tidak terduga mengingat bagian bawah sumur merupakan daerah yang mengadung
hidrokarbon.
Secara garis besar sistem compact spool atau sistem dengan satu spool, profil dalamnya
telah disiapkan untuk menyangga lebih dari satu casing string, misalnya penyangga
intermediate casing string, production casing string dan production tubing string berada dalam
satu spool. Dengan menggunakan sistem satu spool ini, selama proses drilling, BOP tidak
perlu untuk dilepas dari spool hingga tahap completion.
Sistem ini juga mencakup pengembangan pada casing dan tubing hanger. Pengembangan
tersebut yaitu casing hanger dan tubing hanger yang digunakan sudah memiliki sistem
sealing dan penguncian yang terintegrasi dengan badan casing hanger atau tubing hanger.
Gambar 2.1 Wellhead Sistem Compact
Spool (Konfigurasi 3 lubang dalam 1
Conductor)
Wellhead, Hangers dan X-Mas Tree
Gambar 2.2 Unitized Wellheads dalam
fixed platform
Halaman 2 dari 4
Kontributor : Johannes Julianto
3. BUKU PINTAR MIGAS INDONESIA
3. Wellhead Sistem Mud Line Suspension
Pada sistem ini, wellhead dipasang di dasar laut tetapi production casing dan production
tubing-nya disambung hingga platform atau production well jacket. Meski demikian, berat
production casing dan production tubing tidak disangga oleh platform atau production well
jacket.
Wellhead ini terdiri dari dua bagian utama, yakni:
1. Wellhead yang dipasang di dasar laut akan digunakan sebagai penyangga casing
string.
2. Perpanjangan (extension) casing string yang dipasang dari wellhead di dasar laut
hingga subsidiary wellhead di platform dimana BOP dan Christmas Tree akan
terpasang.
Ketika sumur akan selesai, christmas tree dipasang di atas wellhead di dalam laut atau di
atas permukaan laut dengan menggunakaan jacket kecil. Jika christmas tree akan dipasang
pada kedalaman laut, maka perpanjangan casing dilepaskan dari wellhead lalu christmas tree
dipasang.
Sistem ini dapat dijadikan alternatif jika penggunaan sumur ingin ditunda sementara waktu.
Hal ini dapat dilakukan dengan menutup wellhead setelah perpanjangan casing string dilepas
dari mudline.
Gambar 3.1 Wellhead Sistem Mud Line
Suspension dan Christmas Tree
Gambar 3.2 Christmas Tree untuk
Wellhead Sistem Mud Line Suspension
4. Subsea Wellhead
Pada offshore exploration, subsea wellhead ini dapat dijadikan alternatif dimana wellhead ini
dipasang pada sumur di dasar laut yang dalam (deep water) atau sangat dalam (ultra deep
water). Subsea wellhead merupakan sistem wellhead yang tidak memerlukan fixed platform.
Wellhead, Hangers dan X-Mas Tree
Halaman 3 dari 4
Kontributor : Johannes Julianto
4. BUKU PINTAR MIGAS INDONESIA
Prinsip kerja dan fungsi subsea wellhead ini sama seperti wellhead di permukaan (surface),
hanya saja wellhead ini dipasang di dasar laut. Kondisi kerja dan lingkungan yang berbeda
mengakibatkan peralatan dan proses pemasangan menjadi sangat berbeda dengan wellhead
di permukaan.
Dikarenakan wellhead dipasang di dasar laut, maka BOP dan christmas tree juga terpasang
di dasar laut,
Gambar 4.1 Subsea Wellhead
Gambar 4.2 Christmas Tree untuk Subsea
Wellhead
Gambar 4.3 Konfigurasi Subsea Wellhead pada Dasar Laut
*****
Kontributor :
Johannes Julianto
PT. Kvaerner Oilfield Products Indonesia
Wellhead, Hangers dan X-Mas Tree
Halaman 4 dari 4
Kontributor : Johannes Julianto