Tp link error codes

http://www.routersupport.ca/tp-link-extender-setup.html
http://www.routersupport.ca/tp-link-router-troubleshooting.html
http://www.routersupport.ca/tp-link-router-technical-support.html
http://www.routersupport.ca/tp-link-router-support.html
http://www.routersupport.ca/tp-link-router-setup.html
http://www.routersupport.ca/tp-link-router-login.html
TP-Link Router Error Codes
About TP-Link Router Error Codes
There can many TP-Link errors and many forms of codes are available on the internet.
When using Windows 7 built-in PPPoE wizard with a modem working in bridge mode, it fails
and error code 651 appears. The similar problem happens on Windows Vista or previous
versions as well. For example, Error code 678 on Windows XP is equivalent to error code 651 on
Windows 7.
About that problem, if it happens to you, it is highly recommended to adopt following attempts.
Take TD-8616 as an example.
1. Confirm ADSL indicator on TD-8616 is solid on.
If it is flashing on or off, excluding a splitter issue, please check the phone line with your ISP
and make it synchronized.
Since maybe it is not an ISP problem, please hard reset TD-8616. If ADSL light is still not on,
please RMA it.
If ADSL light is solid on but the problem continues, you may go to our website or contact us to
get the latest firmware and upgrade your modem.
2. Set up a new PPPoE connection on your Windows 7.
To find how to set up PPPoE connection of Windows 7.
If necessary, after testing this new connection works, delete the old connection to avoid any
future confusion over which connection should be used.
3. Update rasppoe.sys file and NIC driver.
The root of the problem is believed to be caused by the RAS PPPoE file raspppoe.sys found in
the folder C:WindowsSystem32Drivers. To fix this problem, we will have to replace the
file raspppoe.sys with a new one.
2) After you get the file, before pasting it into C:WindowsSystem32Drivers, be sure that
you rename the original file to something like raspppoe_ori.sys, so that if something weird
happen you have a backup of your original file.

3) Paste the new raspppoe.sys into the directory after you’ve renamed the original file. Try to
connect your modem and it should work fine now.
4. Boot the computer in Safe mode. Disable anti-virus software.
It is suggested to boot the computer in safe mode with networking and check if you are able to
connect to the internet without any issues, safe mode starts Windows with a limited set of files
and drivers. Startup programs do not run in safe mode, and only the basic drivers needed to start
Windows are installed, follow the steps to boot the computer in safe mode with networking:
1. Restart your computer if it is powered on.
2) Tap the F8 key after your computer initially powers on.
3) Once you see the Advanced Boot Options menu you can stop tapping.
4) Use the up/down arrow keys to highlight your selection.
5) Select Safe Mode with Networking and press Enter.
6) You should see drivers loading, and then please wait.
7) You should then be at the Welcome Screen.
8) Logon to your computer using an account with Administrator privileges.
If this step fails then try Disabling Firewall/Security Software if any.
Power cycling your Modem and Router might resolve the problem, here are the steps:
1) Save all your current work, close all open applications, then shut down your computer. Wait
for a minute.
2) Turn your Router off and wait for a couple of minutes.
3) Turn off your modem.
4) Disconnect all the Ethernet cables that are connected to the router and modem and the PC.
5) Reconnect them and ensure that there are no loose connections in between them.
6) Now, switch on your PC and let it boot.

7) Switch on the modem first and after it gets initialized, switch on the router.
6. Modify Link Speed & Duplex Mode to be 100Mbps Full Duplex and disable IPv6.
1) Go to control panel, Network and Internet, Network and Sharing Center. On you left side,
go to change adapter settings.
2) Right click on Local Area connection and go to Properties.
3) Click on Configure. Choose Advance tab. Select Link Speed & Duplex from the Property.
Modify Value to be 100Mbps Full Duplex. Press OK.
In Local Area Connection Properties Window, uncheck Internet Protocol Version 6 (TCP/IPv6).
Press OK to disable IPv6.
Error Code: 52000
Unable to connect to your wireless network
Likely cause: It appears that the security settings entered into the ROUTERSUPPORT.CA are
not the same as what your wireless router is set to allow, or your router is not able to assign the
ROUTERSUPPORT.CA an IP address.
How to fix: Make sure the security key and security type are entered into the
ROUTERSUPPORT.CA exactly as they appear in your router's settings; manually assign an IP
address to the ROUTERSUPPORT.CA.
Manually assign an IP address to your ROUTERSUPPORT.CA.
Assigning an IP address to your ROUTERSUPPORT.CA is easy!
Check for wireless interference, which can affect the signal strength to the
ROUTERSUPPORT.CA. To help minimize wireless interference, try the following:
 Make sure other wireless devices such as cordless phones or wireless speakers are turned
off, and that the ROUTERSUPPORT.CA is an open area without objects or electronics
blocking the signal.
 Change your router's channel setting to 1 or 11. By default, most routers broadcast on
channel 6, which overlaps with other channels and may be weaker. For help doing this,
click here and select your router brand and model (if available). The information you
need is found in the "Broadcast Channel:" area.

If any of the above TP-Link Router Error Codes occurs on your system, You may contact to our
toll free number or visit us at routersupport.ca. We Will help you with no wait resolution.

Tp link error codes

Recommended

Recommended

More Related Content

What's hot

What's hot (7)

Similar to Tp link error codes

Similar to Tp link error codes (20)

More from PPCChamp - Digital Marketing & Consulting Company

More from PPCChamp - Digital Marketing & Consulting Company (12)

Recently uploaded

Recently uploaded (20)

Tp link error codes