The document discusses checking parameters on the RBS side to ensure Hsdsch is enabled properly. It lists attributes from the RbsLocalCell MO that show the hsCodeResourceId is correctly set to 1 for each cell. It also provides commands to check the radio control cell configuration and logical channel availability at the RNC. The final section demonstrates restarting a node using the shm restart command and checking the status.

2. IF Hsdsch disabled side RNC

3. Plz to check the paramattres
hsCodeResourceId side RBS should be 1
194621> get RbsLocalCell= hsCodeResourceId
210804-15:43:13 10.203.139.110 19.0n RBS_NODE_MODEL_U_4_910 stopfile=/tmp/4486
====================================================================================
MO Attribute Value
====================================================================================
RbsLocalCell=S1C1 hsCodeResourceId 1
RbsLocalCell=S1C2 hsCodeResourceId 1
RbsLocalCell=S2C1 hsCodeResourceId 1
RbsLocalCell=S2C2 hsCodeResourceId 1
RbsLocalCell=S3C1 hsCodeResourceId 1
RbsLocalCell=S3C2 hsCodeResourceId 1
====================================================================================
Total: 6 MOs
194621>

4. • Finaly you can check again side RNC with
lst 194621 1.*0 &
lst 194621 1.*1

5. CELL LOGICAL CHANNEL AVAILABILITY
SUPERVISION
• rxasp:mo=rxotg-401;
• rxmfp:mo=rxocf-401,subord,faulty;
• RLSLC:CELL=19301b,LVA=0,CHTYPE=TCH,CHRATE=HR;
• RLSLC:CELL=19213b,LVA=32,CHTYPE=SDCCH;
• RLSLC:CELL=19213b,LVA=16,CHTYPE=SDCCH;
• rxtcp:moty=rxotg,cell=19213b;
• rxcdp:mo=rxotg-31;
• rlcrp:cell=19213b;
• rlslp:cell=19213b;
• RLSLC:CELL=19301b,LVA=16,CHTYPE=SDCCH;
• RLSLC:CELL=19301b,LVA=8,CHTYPE=SDCCH;
• RLSLC:CELL=19301b,LVA=13,CHTYPE=TCH,CHRATE=FR;
• RLSLC:CELL=19301b,LVA=13,CHTYPE=TCH,CHRATE=FR,spv=2;
• RLSLC:CELL=19301b,LVA=13,CHTYPE=TCH,CHRATE=FR,spv=3;
• rxcdp:mo=rxotg-401;
• RLSLC:CELL=19301b,LVA=12,CHTYPE=TCH,CHRATE=FR,spv=2;
• RLSLC:CELL=19301b,LVA=12,CHTYPE=TCH,CHRATE=FR,spv=3;
• RLSLC:CELL=19301b,LVA=12,CHTYPE=TCH,CHRATE=FR;
• rlslp:cell=19301a;
• rlslp:cell=19301b;
• rlcrp:cell=19301b;
• allip:PRCA=43;
•

6. • ALLIP Alarm Functions, Alarm List, Print
• RLCCP Radio Control Cell, Configuration Control Channel Data, Print
• RLCRP Radio Control Cell, Resources, Print
• RLSLC Radio Control Cell, Supervision of Logical Channels Availability Data, Change
• RLSLP Radio Control Cell, Supervision of Logical Channels Availability Data, Print
• RLSTC Radio Control Cell, State, Change
• RLSVP Radio Control Cell, Power Savings Data, Print
• RXCDP Radio X-Ceiver Administration, Managed Object Configuration Data, Print
• RXMOP Radio X-ceiver Administration, Managed Object Data, Print
• RXMSP Radio X-ceiver Administration, Managed Object Status, Print
• RXTCP Radio X-ceiver Administration, TG to Channel Group, Print

11. • Command Line Interface
• »shm restart -n 194584 -rn PLANNED_RECONFIGURATION
• WARNING: Restart is a traffic affecting action. Changes may result in network traffic disturbance.
•
• »shm restart -n 194584 -rn PLANNED_RECONFIGURATION --force
• NodeRestart is initiated on specified node(s) with job name: Shm_Cli_NodeRestart_zmennani_21082021223042
•
• To check the status, run the following command: shm status --jobname
Shm_Cli_NodeRestart_zmennani_21082021223042
•
•
•
Note: This command was forced for execution following automatic Preview Mode
• »shm status --jobname Shm_Cli_NodeRestart_zmennani_21082021223042
• Job Name : Shm_Cli_NodeRestart_zmennani_21082021223042
• Job Type : NODERESTART