5g-solution-overview

1. Etisalat&Ericsson
5Gcooperationandknowledgesharingsessions
5G

2. Ericsson Internal | 2018-02-21
5GFinaltopology,NSAoption3x
gNB BB6630 (midBand)
eNB BB5216 (800,2100)
DUS
DUW
DUG
Router 6471 +TDM1001
Intelligent Connectivity GPS GM Synch
NGS Sych
10G
E1
5G E/// EPC
+ UDC
• Add 5G in co-loc w/ 4G site in NSA with band 4G, FDD
• For FOA sites (B42), anchoring band will be B1 or B20
• Replace TCU/SIU with R6471 with Time/Phase Synch source (GPS GM, 1588v2) and 10Gbps ports
• Both scenarios are shown here; GPON and MW. Dark fiber to be considered for some sites as well
IP/MPLS
PE
ML
10G SFTP+
1G
TCU
1G
10G
WNC Pocket
Router
GPON
OLT
PE
NR AIR6488
B42
5G/4G NSA
Antenna
2G/3G/4G
eCPRI

3. 2018-08-12 | Ericsson Internal | Page 7
IP/MPLS
DAS VRF
BSC
RNC
EPC
ENM
LTE2300
3G900
3G2100
LTE1800
5G
TDM1001
PE-AGG
2G DUG
GPON
R6471
1/10
1/1
1/2
1/3
1/4
1/5
1/9
R6471+TDM1001Connectivity
GPON/DarkFiberBH
RJ45
1G SFP
E1 Cable
10G SFP

4. 2018-08-12 | Ericsson Internal | Page 10
5G New hardware
BaseBand 6630
AIR 6488
Router6471 + TDM1001

5. 2018-08-12 | Ericsson Internal | Page 11
Advanced Antenna System (AAS)
—
64
— TX/64RX with 128 AE (B42 with 192 AE)
Up to
— 200W
EIRP
— upto 76 dBm
Up to
— 100 MHz IBW
Up to
— 3 carriers NR and/or LTE (band dependent)
Max total carrier BW is
— 100MHz for NR, or 60MHz for LTE
3
— x 10 Gbps eCPRI
Weight: ~
— 45 kg
Size (H x W x D): ~
— 810 x 400 x 200 mm (band depended)
— -48 VDC
— -40 to +55 ̊C
AIR 6488

6. 2018-08-12 | Ericsson Internal | Page 8
LTE2300
3G2100
LTE1800
3G900
5G
GPON
DUG1_9
RJ45
1G SFP
E1 Cable
R6471+TDM1001Connectivity
GPON/DarkFiberBH
GPS
DUG2_9
DUG1_18
10G SFP

7. 2018-08-12 | Ericsson Internal | Page 12
AIR6488B42
Technical Specification
Antenna Elements 128
Antenna Branches 64T64R
Antenna Matrix (row x col) 8 x 8, (2x1 subarray)
Band – B42D (FOA) 3500-3600Mhz
Band –B42F 3420-3600Mhz
IBW 100 MHz
Output Power 200 W
Power Consumption <1200 W
Weight ~45 Kg
Dimensions 800*400*150
Type of cooling Passive
CEPT compliance
Multi-layer MU MIMO: Up to 16 layers
NOTE: AIR B42D will be the 1st available in Q3/4, then B42F and B43 in late Q4
Technical Specification
Antenna Elements 128
Antenna Branches 64T64R
Antenna Matrix (row x col) 8 x 8, (2x1 subarray)
Band 3600-3800Mhz
IBW 100 MHz
Output Power 200 W
Power Consumption <1200 W
Weight ~45 Kg
Dimensions 800*400*150
Type of cooling Passive
CEPT compliance
Multi-layer MU MIMO: Up to 16 layers
AIR6488B43
BASEBAND 6630
AIR6488, BB6630, Router
Typical
(W)
Max (W)
Power
supply
Fuse Rating(A)
Total Power
Consumption (W)
3 x AIR6488 1200 -48V DC 3*40 (min 50max) 4200
1x Baseband 6630 120 180 -48V DC 1*30 180
Router 6471/2 35 60 -48V DC 1*6 60
Total/5G 3sectors 4440

8. 2018-08-12 | Ericsson Internal | Page 13
The AIR unit is designed for outdoor use but to ensure optimal
operation, avoid the following:
• Hot microclimates caused by, for example, heat radiated or
reflected from dark or metallic walls or floors .
• Chimney mouths or ventilation system outlets
• Large glass or concrete surfaces .
Avoid radio interference by keeping the area directly in front of
the antenna clear of the following:
• Metal surfaces or objects such as railings, ladders, or chains .
• Equipment generating electromagnetic fields, for example,
electric motors in air conditioners or diesel generators .
• RBS equipment
AIR 6488 Outdoor Installation
Environments to Avoid

9. 2018-08-12 | Ericsson Internal | Page 14
AIR Unit Fuse and Circuit Breaker Recommendations
AIR Unit Parts
Hardware & Power

10. 2018-08-12 | Ericsson Internal | Page 15
AIR 6488 Unit Connection Interfaces

11. 2018-08-12 | Ericsson Internal | Page 16
The AIR unit is equipped with optical indicators that show the system status.
AIR 6488 Optical Indicators

12. 2018-08-12 | Ericsson Internal | Page 17
—Optimized for main-remote configurations
— 19 inch wide, 1U high, <352mm deep
— 15 SFP/SFP+ for CPRI inter-connect to Radio Units reducing the need for Baseband R503
— 2 optical 1/10Gbps SFP/SFP+ ports and 2 electrical 1Gbps RJ45 ports
— Eight External Alarm ports
— Dual 48V DC power feeding
— Self-contained environmental control & field replaceable fan unit
— Hardware Prepared for NR (5G) and eCPRI
Baseband 6630

13. 2018-08-12 | Ericsson Internal | Page 18
comparison
› Baseband 6630/20 is standalone & has its own
climate control
› Baseband 6630/20 has 15 CPRI ports & dual
power feeding
› Typical power consumption estimated to
(at 25°C and typical load)
Baseband 6630: 123W
Baseband 6620: 93W
The RBS
› 6000 chassis is mandatory for Baseband
5216/12
Baseband R
› 503 needed to increase number of CPRI
ports
Baseband
› 6630 will have > 50W lower power
consumption compared to the corresponding
Baseband Main Unit (6601) + Baseband 5216 +
Baseband R503 configuration
Baseband Main Unit (6601) + Baseband 5216/5212 + dummy
OR
Baseband Main Unit (6601) + Baseband 5216/5212 + Baseband
R503
HWAC to enable more than 6 CPRI ports
Main
Unit
6601
Baseband
5212/16
Baseband
R503
6620/30
Baseband

14. 2018-08-12 | Ericsson Internal | Page 19
—In controlled environments
—Mounting in 19 inch racks or in Transmission (TM) compartment in Ericsson enclosures
BB6630 Mounting
D
U
x
D
U
x
PDU
SCU
PCF
R
U
S
R
U
S
R
U
S
R
U
S
R
U
S
R
U
S
SHU
TCU 04
PDU
3.5U subrack
TM Space
Air restrictor plate incl CM
Cable management

15. 2018-08-12 | Ericsson Internal | Page 20
BB6630 Front & rear view

16. 2018-08-12 | Ericsson Internal | Page 21
BB6630 Front panel Interfaces

17. 2018-08-12 | Ericsson Internal | Page 22
BB6630 Factory & power reset
— Use a pen to press down the Factory Reset Button for more than 8 seconds. Wait until the
unit has been restarted and the Operational optical indicator once again is flashing slowly at
0.5 Hz, before releasing the button

18. 2018-08-12 | Ericsson Internal | Page 23
BB6630 installation
• The standard brackets are movable and can be placed in two different positions to adjust the baseband unit
in the right position in the hosting rack.
• When installing the baseband unit in an RBS, make sure to have the brackets in the 50 mm position.
• For cooling purposes the minimum free space is 30 mm behind the baseband unit.

19. 2018-08-12 | Ericsson Internal | Page 24
GROUNDING
• Ground the baseband unit by connecting it to an grounding cable.
• If the unit is installed in an RBS or Enclosure, the grounding cable is not required.

20. 2018-08-12 | Ericsson Internal | Page 25
Hardened and cost effective CSR for emerging market and
suburban sites.
— 30G Full Duplex Forwarding Capacity
— 2x1/10G SFP+, 4x1G SFP, 4x1G RJ-45
— 2 Gbps IPSec ⃰
— 128 L3VPN, 768 PW
— 8Gb packet buffer, 512 queues
— 1RU, 33W(TYP)
— 219 mm x 41mm x 220mm (250mm depth with optional fan)
— -40ºC to 65ºC
— Passive cooling with optional fan accessory for temp above 55C
— Advance sync features
— Programmability and SDN support
Router 6471
Indoor small site router
⃰ HW prepared for 8 Gbps

21. 2018-08-12 | Ericsson Internal | Page 26
6471 interfaces & capacity
Dual power
feed
2x GE/10GE SFP+ ports
4x GE SFP ports
4x 100/1000 Base-T RJ45 ports
1x GE Base-T Ethernet for
out-of-band management
1x USB 2.0 port
1x RJ45 Alarm port for 3 input
and 1 output alarm contacts
1x RJ45 console
port
Synchronization interfaces:
1x RJ45 port 1PPS+TOD (ITU-T G.703)

22. 2018-08-12 | Ericsson Internal | Page 27
— 8xE1/T1 Abis over IP
— 16 x T1/E1 CES
— 1 x GigE RJ-45/SFP combo port
— 1 x Ethernet management port
— 1RU, 20W(TYP)
— 219 mm x 41mm x 220mm
— -40ºC to 65ºC,
— Passive cooling
— Managed as Attached Unit of any indoor Router 6000 variants
(e.g. No seperate IP address)
— Can be installed in the same 1RU hosting shelf next to Router
6471
TDM 1001
E1 CES/ABIS expansion module
19”
1RU
Router 6471
TDM 1001
Hosting Shelf

23. 2018-08-12 | Ericsson Internal | Page 28
TDM 1001 interfaces & capacity
1x GE SFP
1x 100/1000 Base-T RJ45 ports
1x GE Base-T Ethernet for
out-of-band management
Dual power feed
8x RJ45 ports for up to 16x E1/T1 interfaces
1x RJ45 console port

24. Ericsson.com